SPAL USA MULTIRCU7TX 7 Channel Control Module User Manual users manual

Download:
Mirror Download [FCC.gov]
Document ID	249536
Application ID	uLxi/tjoGrUWDUiehqQzIQ==
Document Description	users manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	53.11kB (663897 bits)
Date Submitted	2002-06-13 00:00:00
Date Available	2002-06-12 00:00:00
Creation Date	2002-04-23 11:40:39
Producing Software	Acrobat 5.0 Image Conversion Plug-in for Windows
Document Lastmod	2002-04-23 11:50:44
Document Title	users manual
Document Creator	Acrobat 5.0 Image Conversion Plug-in for Windows

AMENI TY
Installation Manual &
Operation Instructions
SHAVED DOOR KIT
MODELS:
SHAVED
SHA VED-2-A CT
SHAVED-2—SIL35
MADE IN THE U.S.A.
Note: Read this instruction manual
thoroughly before installation.
TECH SUPPORT: 800-454-7725
EMBII I(I'I' IllfllllllES I'll!
I’llllllWIllll BOMI’IIIIEII'I'S:
(1) Multi-RCU Unit
(1) Shaved Harness
(2) #10 Blue Rings
(1) Emergency Switch
(2) HELLA 40 Amp Relays
SHAVED-2-SIL35
(2) 35-Pound Solenoid Kits
(4) Mounting Bolts
(4) Nuts
(4) Washers
(2) Yellow Butt Connectors
(2) Yellow 5/16 Rings
SHAVED-2-ACT
(2) 8-Pound Actuators
(2) Blue Butt Connectors
i I ‘I m
Installation instructions for
AMENITY Shaved Door Handle Kit
SHAVED-2-ACT/SHAVED-2-SIL35
This kit is designed to operate two or more functions. Both doors and five other func-
tions can be controlled with the AMEN/TY four-button remote control The additional
channels can be used to operate power door releases, trunk releases, roll up or down
power windows or control linear actuators.
Channels 3 through 7 are all negative outputs. Please refer to the diagrams near the
end of the instruction manual for positive, negative and reverse trigger diagrams.
Wiring is important to the overall finished project. Make sure all wires are properly
- grounded, free of potential damage and are correctly fused.
Basic functions of the AMEN/TY Shaved Door Kit:
The remote control supplied with your kit is seven channel, four button.
Channel 1: opens driver’s side door.
Channel 2: opens passenger's side door.
Channel 3:
Channel 4' Optional 250 mA (milliampere) negative outputs.
Channel 5- Additional relays are required for each channel.
Channel 6:
Channel 7:
Basic functions of the remote control:
Channel 1: Button 1
Channel 2: Button 2
Channel 3: Button 3
Channel 4: Button 4
Channel 5: Button 1 + Button 2
Channel 6: Button 1 + Button 3
Channel 7: Button 1 + Button 4
Mounting and wiring instructions:
10-Pin Wiring Harness (by color) 10-Pin Wiring Harness (Qy function)
GRAY Channel 1 Channel 1 GRAY
RED +12 VDC to battery Channel 2 BLUE
BLUE Channel 2 Channel 3 WHITE
BLACK Ground Channel 4 YELLOW
WHITE Channel 3 Channel 5 BROWN
YELLOW Channel 4 Channel 6 PURPLE
PINK Channel 7 Channel 7 PINK
PURPLE Channel 6 Power (+12 VDC) RED
BROWN Channel 5 Ignition ORANGE
ORANGE Ignition Ground BLACK
Receiver mounting and wiring:
The receiver is the item that provides all of the outputs to activate the different functions,
Because of the nature of the receiver module, it must be mounted in the interior of the
vehicle where there is no moisture.
Notes:
Do not plug in the receiver module until the all of the wiring is complete!
Do not ground the antenna wire!
Options:
Hidden Switch: (optional)
It is a good idea to mount the provided external switch on the vehicle to allow entrance to
the vehicle in case of lost transmitters or leaving the keys in the vehicle. (See diagram.)
(continued)
Channels Three through Seven (optional)
These wires are negative outputs for an optional accessories. Each can be used as either a
trunk/hatch release, power window up or down, remote starter, control linear actuators or any-
thing else you can imagine See diagram for installation ideas.
NOTES: One additional relay is required to operate each channel
Connecting or activating the additional relays is not required for optimal use.
Actuator mounting and wiring: (SHAVED-Z-ACT)
The actuators are to be mounted in the vehicles doors either vertically or horizontally. Mount
the motors vertically so that the motors face upward so there is less of a chance for water to
condensate inside the actuator. They are to be attached to the latch in the same position as
the exterior door handle (see diagram). The actuators have two wires and can push or pull
depending on how you mount them in the door (see table below).
Actuator movement Red wire Blue wire
Connect to blue relay wire Connect to ground
Connect to ground
Remote jumper leads on the batteg: (optional)
The installation of remote jumper leads on the battery will allow you to jump-start or charge
your battery in case of a power failure.
Note: Always plan for the worst case scenario when building custom cars or trucks. Think
about the application for the product you are installing and the problems that could hap—
pen. Take the time and come up with a solution that will let you remedy the situation with
the least amount of hassles.
If you have any technical questions feel free to call us at 1-800-454-7725.
R ro rammin the Remote Controls
Turn off ignition. Press and release the valet switch on the unit three times, the LED will
flash twice and come on solid the third time. Next, press button one (1) on one remote,
the LED will go off then come back on. Then press button one (1) on the other remote,
the LED will go off then come back on. When the LED remains on, programming is com-
plete.
AMENITY Attach to latch olitem to be pulled
35-Pound . fl
Solenoid W
Mounting
Diagram
Boll to door skin or panel
a/
4—— While: Power line
AMENITYSeven-Channel
Shaved Door Handle Kit
Wiring Diagram
GRAY - Channel 1 — Driver’s Door
RED - +12 VDC Power Supply
BLACK - Ground —12 VDC
WHITE - Channel 3
YELLOW - Channel 4
PINK - Channel 7
PURPLE — Channel 6
BROWN — Channel 5
ORANGE - Ignition
RED: +12 banery
I I
— +
Battery
fl
IE]
GRAY To Back up Swnch
GREEN: Channel One (1)
Note:
Additional Relays are NOT included.
BLUE: Channel Two (2)
I B in m
Actuator Installation
Instructions
1. Attach rod to actuator.
2. Attach rod to door latch or
item to be pulled/pushed.
3. Mount actuator to door
paneL
Remember, if possible, mount the
motor vertically to allow for water
drainage.
Hidden Switch Wiring Diagram
8nd. Slick“:
Channels 3 - 7 Wiring Options
Wiring suggestions of the optional negative
outputs using a SPDT automotive relay
Positive Trigger
Works on trunk/door pops
and other +12 VDC systems
Channel Three Output 85
Negative Trigger
Works on trunk/door pops
and other —12 VDC systems
I Th
Channe ree Output 85
Reverse Trigger
For power windows and linear
actuators
Channel Three Output 55
+12 VDC (Fuse Correctly)
+12 VDC Output to use
+12 VDC (Use 5Amp Fuse)
-12 VDC Output to use
+12 vdc (Fuse Correctly)
Power Vlfindow ln ctioris
Cut the power window wire in half.
(You can use the up or down wire
depending on which direction you
want the window to go.) Then splice
a relay in between per the diagram.
Please note that you will need one
relay per window for this flirtation.
Limited Warranty Statement
I.E.I. AMENITY LINE WARRANTY STATEMENT
I.E.I. warrants this product to be free from defects in mate—
rial and workmanship for a period of one (1) year from the
date of sale to the original purchase, and not more than
two (2) years from the date of manufacture. I.E.I. will
repair this product free of charge if, in the judgment of
I.E.l., it has been proven defective within the warranty
period. The product should be returned, at the customer
expense, to Iowa Export-Import, 512 Tuttle Street, Des
Moines, Iowa 50309-4618. This warranty does not cover
any expenses incurred in the removal and/or reinstallation
of the product.
This warranty does not apply to any product damaged by
improper installation, accident, misuse, abuse, improper
line voltage, fire, flood, lightning, other acts of God, or a
product altered or repaired by anyone other than I.E.I.
This warranty is in lieu of other warranties, expressed or
implied, including any implied warranty of merchantability.
No person is authorized to assume for LEI. any other lia-
bility concerning the sale of this product.
IMPORTANT — KEEP YOUR INVOICE
WITH THIS WARRANTY STATEMENT !
® gem: I @WA
AbVANCEo rrcrwotosizs ”119555111110”
512 Tuttle St, Des Moines, IA 50309, info@spal-usa.com, www.spai-usa.com
Main/Sales: 800-345-0327, Sales: 888-SPAL-USA, Technical: 800-454-7725

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Modify Date                     : 2002:04:23 11:50:44-04:00
Create Date                     : 2002:04:23 11:40:39-04:00
Creator                         : Acrobat 5.0 Image Conversion Plug-in for Windows
Page Count                      : 8
Mod Date                        : 2002:04:23 11:50:44-04:00
Creation Date                   : 2002:04:23 11:40:39-04:00
Producer                        : Acrobat 5.0 Image Conversion Plug-in for Windows
Metadata Date                   : 2002:04:23 11:50:44-04:00
Has XFA                         : No

EXIF Metadata provided by EXIF.tools