SABINE SW60 UHF HANDHELD TRANSMITTER User Manual 1

Sabine, Inc. UHF HANDHELD TRANSMITTER 1

Contents

User Manual 1

SMART SPECTRUM®WI R E LE S S   SYSTE M SOperating GuideSWM6000 915 MHz SystemsSWM7000 2.4 GHz SystemsWIRELESS MICROPHONESthe sound of innovation™
2Sabine Smart Spectrum® Wireless© 2009  Sabine, Inc.Need other EC docs hereDeclaration of Conformity
3Sabine Smart Spectrum® WirelessLIT-SWM6-7000-OG-EN-090215.indd - rr© 2009  Sabine, Inc.Declaration of ConformityEC - DECLARATION OF CONFORMITYCE MarkingWe, the ManufacturerSABINE, INC.13301 NW US HIGHWAY 441ALACHUA, FLORIDA USAdeclare that the productRECEIVERSABINE MODEL SWM7000Is in conformity withCouncil Directive: 73/23/EEC and 89/336/EEC (EMC Directives)Standards to which conformity is declared:EN 60065: 2001EN 55022: 1998 Class BEN 50082-1: 1998      Manufacturer Signature: __________________________     Date: __________   Name:  __________________________ Doran Oster, President28 April, 2003
4Sabine Smart Spectrum® Wireless© 2009  Sabine, Inc.Table of ContentsThis operating guide written for receivers using Sabine SWM Remote Control Software version 2.0 and above.9.  DE-ESSER  339.1.  De-mystifying De-essers  339.2.  The Sabine De-esser  339.3.  Using the De-esser  3310.  PROGRAM SAVE & RECALL  3410.1.  Saving a Preset  3410.2.  Loading a Preset  3410.3.  Naming a Preset  3410.4.  Power Off Memory  3411.  MULTIPLE SYSTEMS OPERATION  3511.1.  Overview  3511.1.1.  Multiple System Interference  3511.1.2.  Setup Complexity  3511.2.  Antenna Distribution Amplier  3611.3.  Antenna Distribution Amplier Connection  3612.  EXTENSION ANTENNAS  3812.1.  Overview  3812.2.  Antenna Cabling & Cable Loss  3813.  REMOTE CONTROL OPERATION  4013.1.  Overview  4013.1.1.  Single vs. Multiple Receiver Control   4013.1.2  Features & Controls Added Software  4013.1.3. Software Multiple Unit Control  4213.2.  Software Installation   4213.2.1.  Requirements & Recommendations  4213.2.2.  Connections  4213.2.3.  Installing the Software  4313.3.  Launching the software  4313.3.1.  Off-Line Edit/Demo  4313.3.2.  Connecting Receivers.  4313.4.  Remote Control Operation  4413.4.1.  Two Views, Two Sets of Controls  4413.4.2.  Menus, Icons & Hot Keys  4414.  TIPS & TROUBLESHOOTING  4814.1.  Tips for Maximum Performance  4814.2.  Troubleshooting  4814.3.  Common Sources of RF Interference  4914.3.1 RF Sources  4915.  FBX THEORY & PRACTICE  5115.1.  Introduction to FBX®  5115.2.  The Advantages of FBX Filters    5115.3.  Parametric Filters and FBX  5215.3.1.  The FBX & True Mobility® Advantage   5314.3.2.  FBX Fixed & Dynamic Filters  5314.3.3.  FBX Filter Width  5414.3.4. Who Benefits from FBX?  5415.  APPENDICES  55Appendix A:  Beltpack Connector Wiring Diagrams  55Appendix B:  Antenna System Diagrams  55Appendix C:  Specications  56Appendix D:  Dip Switch Settings  58Appendix E:  Frequency Chart  59Appendix F:  Battery Endurance Tests (Typical)  60Appendix G:  Changing Audix Mic Capsules (SW70-H)  6016.  CAUTIONS & WARRANTY  61INDEX  631.  INTRODUCTION  51.1.  Section Contents  52.  PRODUCT VIEWS  62.1.  Receivers  62.1.1.  Front panel views  62.1.2.  Back panel Views  62.2.  Transmitters  72.2.1.  Handheld  72.2.2.  Beltpack  72.3.  Components  73.  QUICK SETUPS  83.1.  Receiver & Transmitter Quick Setup   83.2.  FBX Quick Setup  83.3.  Tips for Good RF Performance  123.4.  Common Sources of RF Interference  124.  TRANSMITTER OPERATION  144.1.  First step 144.2.  Displays and Settings 144.2.1.  LCD Display 144.2.2.  Accessing Transmitter Controls  154.2.3.  Adjusting Transmitter Settings  164.2.4.  Transmitter Battery Management  175.  RECEIVER OPERATION  205.1.  LCD Display.   205.2.  Parameter Control & LCD Display  225.2.1.  One set of Controls for 1 or 2 Channels  225.2.2.  Channel Select / Contrast Button.  225.2.3.  Special LCD Display Messages.  235.3.  RF Channel Select  235.4.  Output Level  235.5.  Channel Mixing  235.5.1.  How to toggle channel mixing mode  235.5.2.  Controlling the reciever in channel mixing mode  245.6. Guitar Cord Simulating  24 5.7. Receiver Antenna Placement   245.7.1.  Multi-path Interference  245.7.2.  Receiver & Antenna Placement Tips  246.  MIC SUPERMODELING™  266.1.  Introduction  266.2.  Emulation Choices  266.3.  Mic Modeling Front Panel Control  266.4.  Future Microphone Modeling Choices  276.4.1.  Mic Model Upgrade Instructions  277.  FBX FEEDBACK EXTERMINATOR®  287.1.  FBX Introduction  287.1.1.  FBX Fixed Filters  287.1.2.  FBX Dynamic Filters  287.1.3.  Balancing Fixed & Dynamic Filters  287.1.4.  FBX Filter Width  287.2.  FBX Set Up  287.2.  FBX Bypass Button  298.  COMPRESSOR/LIMITER OPERATION  308.1.  Basics of Compression  308.2.  Using the Compressor  308.3.  Suggested Compression Settings  318.3.1.  Vocal Settings  318.3.2.  Guitar Settings  31
5Sabine Smart Spectrum® WirelessLIT-SWM6-7000-OG-EN-090215.indd - rr© 2009  Sabine, Inc.1.  INTRODUCTIONCongratulations on purchasing a Sabine 2.4 GHz Smart Spectrum True Mobility™ Wireless System. True Mobility™ Wireless Systems give you all the built-in processing you need on every microphone, and offer unique and powerful features unavail-able with any other wireless microphone1.1.  Section ContentsSection 2 Product Views — illustrates system components (front & back panel views, transmitters, accessory lists and part numbers).Section 3 Quick Setup — gives the Quick Setup procedures for Receiver & Transmitter Operation and using the FBX Feedback Exterminator®. Note that there is also a quick-start label on top of your True Mobility receiver for the Sabine FBX Feedback Exterminator®, Compressor/Limiter and De-Esser functions. Section 4 Transmitter Operation — details transmitter setup and operation.Section 5 Receiver Operation — details receiver installation and setup.Section 6 Mic SuperModeling™ — explains the use of the Sabine Mic SuperModeling™ and lists the microphones modeled.Section 7 FBX Feedback Exterminator® — explains how to set up your FBX filters.Section 8 Compressor/Limiter — explains the use of the Compressor.Section 9 De-Esser — details operation of the adaptive De-Esser.Section 10 Program Save & Recall — explains how to save and recall individual program settings.Section 11 Multiple Systems — how multiple systems interface, computer control of multiple systems, suggestions for maximizing the number of collocated systems.Section 12 Extension Antennas — how to get maximum performance using a Sabine Extension Antennas (Antenna Distribution Amplifier also available for multi-receiver installations).Section 13 Sabine Remote Control Software — how to control up to 70 channels from one PC.Section 14 Tips & Troubleshooting — gives tips on how to get the best performance from your Sabine Wireless, and describes some possible operating problems and their solutions.Section 15 Appendices  — wiring diagrams, frequency charts, specifications, typical system diagrams and dip switch settings for Sabine 2.4 GHz Wireless systems.Section 16 Cautions & Warranties — states caution and warranty information for your True Mobility™ Wireless sys-tem.IndexIntroductionImportant note about using this Operating GuideThis guide covers the operation of both the SWM6000 and SWM7000 Wireless Systems.  The basic operating procedures for these two series are the same.  The crucial differences are the frequency bands each of these series uses, and the number of available channels.SWM6000:  Offers XX channels, and uses the 915 MHz band.  All transmitters and receiv-ers include the number “6” or the designation “M9” in the part number to denote this series.SWM7000:  Offers 70 channels, and uses the 2.4 GHz band. All transmitters and receivers include the number “7” or the designation “M1” in the part number to denote this series.These products may be used together in the same location, but remember that transmitters and receivers must always work together.  For example, in order for an SWM6000 Series system to work, the transmitters and receivers must both be from that series.  Other components in your system can be mixed between these two series. These include lavalier and headworn mics, mic clips and chargers, cables and adaptors, and anything that is not involved in the transmission or reception of the wireless signal.
6Sabine Smart Spectrum® Wireless© 2009  Sabine, Inc.Product ViewsCh. AChannel Select,ContrastCh. BChannel Select,ContrastFig. 2b - SW71-R (SW62-R) One-channel ReceiverFig. 2a - SW72-NDR & SW72-R (SW62-NDR & SW62-R) Two-channel Receivers Antenna 1 Front MountCh. ADisplayAntenna 2 Front MountPowerCh. B DisplayProgramOutput LevelRF Ch. SelectCompressorLimiterDe-esserMic ModelFBXFig. 2e - SW71-R (SW61-R) One-channel ReceiverFig. 2d - SW72-R (SW62-R) Two-channel ReceiverFig. 2c - SW72-NDR (SW62-NDR) Two-channel Receiver w/Network & Digital InterfaceAntenna 2 AES3Digital OutputSync InputAC Power& FusesRS485 Net-workRS232 SerialUSB Port,Dip SwitchesMic/Line Balanced Output BMic/Line Balanced Output AAntenna 12.  PRODUCT VIEWS2.1.  Receivers2.1.1.  Front panel views2.1.2.  Back panel ViewsSee Page 55 for the chart of DIP Switch Settings
7Sabine Smart Spectrum® WirelessLIT-SWM6-7000-OG-EN-090215.indd - rr© 2009  Sabine, Inc.Product ViewsProduct ViewsFig. 2h - SWC70CL - SW70-H13 (SW60-H13), SW70-H15 (SW60-H15) & SW70-H19 (SW60-H19) Mic Clip with Built-in ChargerFig. 2i - SW65 and 75-T Beltpack Transmitter2.3.  Components (for a complete list see the Sabine Catalog)ReceiversSW62 and 72-NDR: 2-Ch. Receiver w/Network & Digital InterfaceSW62 and 72-R: 2-Ch. ReceiverSW61 and 71-R: 1-Ch. Receiver MicrophonesSWT31L-TA4: Cardioid Lavalier MicSWT56W-TA4: Headworn MicSVT70BW-TA4: Voice Technologies Omni Headworn Mic (Black)SVT70LW-TA4: Voice Technologies Omni Headworn Mic (Tan)SVT80BW-TA4: Voice Technologies Cardioid Headworn Mic (Black)SWTVT50-TA4: Voice Technologies Miniature Omni Lavalier SVT40L-TA4:  Voice Technologies Sub-Mini Omni Lavalier SWT70G-TA4: Instrument Input w/cableTransmittersSW65 and 75-T: Beltpack TransmitterSW60 and 70-H13: Handheld Mic w/Dynamic Element (Audix OM3)SW60 and 70-H15: Handheld Mic w/Dynamic Element (Audix OM5)SW60 and 70-H19: Handheld Mic w/Condenser Element (VT)AntennasSWA700: TNC Front to Rear Converter Kit (Set of 2)SWA6SS: 2.4 GHz Antenna Distribution Amp for 6 systemsSWASS-EXT: Extension Antenna Kit (Set of 2)SWAANT-2.4: 2.4 GHz Antennas (2)SWATNC-N: RF Adaptor cable, Set of 4, TNC to NBSWATNC-MCA: TNC Male Crimp Connector 2.4 GHzSWACA15(or 30)-TNC: RF Cables, RG58, TNC, One PairBatteriesSWBAA2: Rechargeable NiMH AA set for SW75-T & H1Mic & Transmitter AccessoriesSWCRJ45: RS485 Serial Cable for ND ReceiversSWC70CL-1: SW60/70-H Mic Holder w/Built-in ChargerSWC70CL-12: Stage clip for SW70-HSWCPOWR-EXT: Charger extension cable (3 meters)SWCPOWR: Plug-in charger for SW60/70 Series TransmittersSWC4P-TA4: Standard Mini-XLR ConnectorALKALINE BATTERY CAUTION       Alkaline batteries must be one of following types: NEDA: 14A  ANSI: 14A  IEC: LR14!!AntennaSwitchTA4Mini-XLR ConnectorTop viewBelt clipSWC-POWR plug-in char-ger jackselecton   on   onoff  mute  on2.4 GHz SMART SPECTRUM12BatterySWC-POWRplug-in charger jackShown with cable attached. Requires assembly.Switch BatteryLCDTransmitter Controls1  Select Button2  Up  Button3  Down Button2.2.  Transmitters2.2.1.  Handheld —  DO NOT USE RECHARGEABLE ALKALINE BATTERIES  — 2.2.2.  Beltpack123up down3(for a complete list see the Sabine Catalog)
8Sabine Smart Spectrum® Wireless© 2009  Sabine, Inc.3.  QUICK SETUPS3.1.  Receiver & Transmitter Quick Setup Please read Section Four Transmitter Operation and Section Five Receiver Operation for a complete understanding of how to set up your Sabine Smart Spectrum True MobilityTM System.Quick Setups  Turn  the  OUTPUT  LEVEL of the  receiver and mixer gain to the mini-mum settings.2  Connect the output (¼-inch or XLR jack) of your receiver to the mic or line input of your mixer or amplifier (the receiver output gain can be adjusted to match the mixer input).3Mixer Balanced Input (XLR)Mixer Unbalanced Input (TRS)1.  Turn on the receiver.2.  Tap the Channel Select/Contrast button to edit a receiver channel. (Not necessary on 1-channel SW71-R & SW61-R receivers).3.  Turn the RF Channel Selector knob to the de-sired channel.NOTE: Dual channel receivers will not allow you to select the same RF channel for both channels.4Power SwitchRF Channel Selector Channel Select/Contrast button (selects receiver channel to edit)Transmitter range is 100 meters line-of-sight  Be sure that all transmitters are off.  Position receiver so that the antennas are within visual range of the intended transmitter locations. Transmitter range is about 100 meters, but structural objects in the transmission path can reduce that range. For best results, maintain a line-of-sight path between receiver antennas and transmitters (see Section 12). Use the TNC Rear-to-Front Kit (SWA700) included with the receiver to move antennas to front if necessary. See Appendix B for more information on multiple-system connection.Use Sabine’s SWASS-EXT Extension Antenna Kit when line-of-sight path is not possible from receiver location.1NOTE: Front panel RF Signal display will only register Sabine transmitters. It will not show RF interference. Use the RF Scan function in the software to scan for potential RF interference.Selecting RF Channels: It is best to keep the system’s  channels  close together  at  the low or high end of the spectrum, i.e. chan-nels 1, 2,3,4,5 or channels 65, 66, 67, 68.   If there is another 2.4 GHz source in the room, grouping the channels reduces the chances of an overlap.  Do not start by spreading your channels throughout the full channel range of the system – you are more likely to encounter interference this way.
9Sabine Smart Spectrum® WirelessLIT-SWM6-7000-OG-EN-090215.indd - rr© 2009  Sabine, Inc.6  Gain Adjustment Settings  1. Transmitter (PAD Adjustment).  Adjust the Transmitter PAD setting if last segment of the Transmitter or Receiver Audio Level Meter lights up often, or remains on when mic or beltpack is used.  1. Use the Transmitter  Select button to scroll through functions until PAD flashes in the Transmitter LCD.  2. Use the Up or Down buttons to select the desired setting. Selec-tion is stored after 3 seconds of inactivity.  3. Check to see if Audio Level Meter stays out of Clipping Zone1.  Turn on the transmitter.2.  Use the SELECT button until CHANNEL appears in the LED. NOTE: the transmitter is muted during editing.3.  Use the UP or DOWN button until the desired channel appears above CHANNEL.4.  Check that the receiver’s RF SIGNAL display now indicates a strong signal (at least 3 bars).5Quick SetupsTo  Close: Push  door  up  and  snap closed.To Open: Pull down on both battery door releases and then pull door open.  2. Receiver.   Adjust the receiver Output Level to supply a strong input level to the mixer, amplifier or active loud-speaker.  If your receiver output is connected to a microphone level input on the mixer, keep the receiver output gain lower than when connecting to a line level mixer input. NOTE: -10 is a good place to start.  3. Mixer.  Adjust the output gain of the mixer so that the mixer output meters approach clipping when all the inputs to the mixer are active, and the audio program reaches its peak level.  4. Amplifier/active loudspeaker/crossover.   Finally, adjust the amplifier gain control (and/or crossover gain, if one is used) to provide the desired level of sound pressure in the auditorium or listening area.Adjust PAD setting so that Receiver Audio Level Meter stays out  of the  clipping zone (last segment)SELECTSee Section 4.2.3 Adjusting Transmitter Settings for more information.Transmitter Controls1  Select Button2  Up Button3  Down Button123To  Close:  Turn  the housing  and  push up until  it  meets  the threads, then screw on.To  Open:  Unscrew lower portion of  mi-crophone.  Pull down as you continue to turn the housing.selecton   on   onoff  mute  on2.4 GHz SMART SPECTRUM12up down3Beltpack Opening/Closing Instructions
10Sabine Smart Spectrum® Wireless© 2009  Sabine, Inc.Fig. 3d - FBX: SETUP Fig. 3e - SETUP indicator flashingQuick Setups3.2.  FBX Quick Setup   Place microphone and speakers in primary position.12  Press and hold the SETUP button (Fig. 3d) on the receiver until the LCD SETUP indicator (Fig. 3e) flashes 4 times and SETUP stays lit — then release it.   NOTE: DO NOT TALK INTO YOUR SYSTEM while in Setup Mode. Slowly raise the gain on the mixer or amp until FBX eliminates the first few feedback tones. With each new feedback frequency, you will hear a short, quiet burst of feedback that will disappear immediately as a filter is set.  Pause raising the gain, and move the microphone to another area where it will be used.  Resume slowly raising the mixer gain, until FBX eliminates a few more feedback tones.  NOTE: When choosing microphone setup locations, try to anticipate likely areas where the microphone will be positioned or moved to, or areas that may be especially prone to feedback problems (e.g., under an overhead speaker).Location #1Location #2Location #3  Repeat until the SETUP  indicator automatically turns off and the READY indicator comes on.  NOTE: You may quit SETUP mode at any time prior to its auto-matic exit by simply pressing the READY button. This will enable ready-to-operate status, but with fewer fixed FBX filters in place.  In the default factory setting, dynamic FBX filters will still be held in reserve to catch and eliminate new feedback, regardless of how or when SETUP mode is exited. (See Section 14.3.2 for details on the differences between fixed and dynamic FBX filters and Section 13.4.2.1 for instructions on changing the balance 543FBX BYPASS CAUTIONBypassing FBX filters may allow suppressed feedback to be released!Location #4(if necessary)Mixer Channelof fixed versus dynamic FBX filters using the Remote Control Software or Appendix D for using the Dip Switches on the back of the receiver).3.2.2. FBX BypassThe BYPASS button (Fig. 3d) bypasses only the FBX filters, and not the additional signal processing (de-essing, compression and Mic SuperModelingTM) available on the True MobilityTM Wireless Receiver. This is a useful button that allows comparison of the sound quality when FBX filters are in place, to the sound with no filters (the qual-ity should be very similar).  Before pressing BYPASS, take care to reduce your overall system gain so that you do not release suppressed feedback!
11 Sabine Smart Spectrum® WirelessLIT-SWM6-7000-OG-EN-090215.indd - rr© 2009  Sabine, Inc.Quick SetupsVocal Settingsratio  A soft voice could be set to 2:1, whereas a loud voice might require a ratio setting of 6:1.thresh  The higher the threshold setting, the more signal is required to initiate compression.  Ideally this should be set to reign in peak levels, and allow signals of lower gain to pass uncompressed.  Threshold settings will depend on the nature and variety of the signal source.attack  Short attack times usually work well for voice.  However, too strong a compression ratio, too low a threshold, and too fast an attack may attenuate speech consonants, which provide important intel-ligibility cues to the audience, thus compromising clarity.Guitar Settingsratio  A high compression ratio (with gain makeup) will add sustain to held notes and chords.thresh  Moving the threshold  will change the audible thick/thinness of the guitar tone, but generally you want to compress all the notes played. attack  Be wary of too quick an attack, which may reduce the percussive attack of the guitar notes.In general, be wary of too much gain makeup, and too high a compression ratio, which may make a noisy guitar amplifier more objectionable. Ratio settings might range from 6 to 19:1, threshold variable, slower attack, soft knee, output gain boosted slightly to significantly depending on amount of compression.Bass Guitar Settingsratio  Set to 4:1thresh  Set to compress peaks only.attack  Quick attack, medium release, hard knee; (try various release settings, depending on the speed of notes played).gain  Output boosted slightly.MIC SUPERMODELINGTMDE-ESSERratiothrEshattaCkratiothrEshattaCkNOTE:    Use these settings as a place from which to start, then adjust to your own satisfaction.VocalsShort attack is better for vocals. Be careful not to over attenuate speech consonants.Soft voice Loud voiceSoft voice Loud voiceGuitarLess Sustain More SustainThinner sound Thicker soundBe wary of too quick an attack, which may re-duce the percussive attack of the guitar notes.NOTE: Mic SuperModelingtm is not avail-able using beltpack transmitters.COMPRESSOR/LIMITERMiC supErModElingScroll through  available  microphone settings.  See website for additional downloadable microphones.Less reduction More reductiondE-EssEr
12Sabine Smart Spectrum® Wireless© 2009  Sabine, Inc.Quick Setups3.3.  Tips for Good RF Performance•  It is best to keep the system’s channels close together at the low or high end of the spectrum, i.e. channels 1, 2, 3, 4, 5 or channels 65, 66, 67, 68 (41, 42, 43 on the SWM6000 series).   If there are other 2.4 GHz or 900 MHz sources in the room, grouping the channels reduces the chances of overlap.  Do not start by spreading your channels throughout the full channel range of the system -- you are more likely to encounter interference this way. •  Avoid potential sources of RF interference by performing a scan using Sabine’s Remote Control Software., which will reveal the ambient RF level in your area on each channel of your system. Please refer to Section 13.4.2.5. for information on the RF Scan function, which will automatically determine the best RF channels to use.•  If you cannot perform a scan then proceed to use your system, beginning with Channel 1.  If you hear any RF “hits” or dropouts, then move to another of the available channels. If you have multiple mics keep all your channels grouped together.•  For best results, maintain line-of-sight from transmitter to receiver.  Use either front or rear panel antenna mounting to maintain line-of-sight.•  Mount receiver antennas at 90 degrees to one another, leaning away at 45 degree angles, in the same plane. •  When using multiple receivers, try to maintain at least 1 foot (30 cm) distance between antennas from different units. When such antenna spacing proves difficult or impossible, we  recommend using  Sabine’s  SWA6SS  Antenna Distribution Amplifier.  The SWA6SS works with up to six receivers, or 12 channels.•  Maximize the distance between the receiver and light sources, such as fluo-rescent bulbs or neon signs, which may emit very short-range, broadband interference. •  Maximize the  distance between  transmitters and  receivers and  potential sources of RF interference.•  Maintain a minimum distance of at least 3 meters (10 feet) between transmit-ters and receivers or extension antennas. This can solve many anomalies.•  Turn on your system one component at a time, beginning with the first re-ceiver.•  Be careful not to set more than one transmitter to the same channel; each paired transmitter and receiver should be set to unique corresponding chan-nels, until all channels are receiving clearly and cleanly.3.4.  Common Sources of RF Interference•  Microwave ovens:  In the vast majority of situations, interference from mi-crowave ovens will not affect performance of your SWM series microphone systems.  Since barriers such as walls work to block interference, a microwave oven will likely present a problem only when located in fairly close proximity within the same room as the wireless receiver (or reception antenna). See caution at left.•  Wireless Local Area Networks (WLANS):  These computer network devices allow computers to connect via wireless devices that act as both receivers and transmitters.  These low-powered transceivers often have selectable channels and can utilize the entire 2.4 GHz band.  In general, Sabine microphones should not be  affected by these WLANS  because their spread  spectrum technology does not present a problem for the Sabine Smart SpectrumTM system. The Sabine wireless system will not interfere with the WLAN. See caution at left.As a general precaution, keep 2.4 GHz or 900 MHz cordless telephones, microwave ovens, WLAN  antennas and  2.4  GHz wireless video camera transmitters twice the distance  from  your Sabine wireless microphone system antennas as that of your Sabine transmitters.Antenna Placement Caution
13 Sabine Smart Spectrum® WirelessLIT-SWM6-7000-OG-EN-090215.indd - rr© 2009  Sabine, Inc.•  2.4 GHz or 900 MHz Cordless phones:  These home telephones broadcast at very low power and should not present interference problems for your Sabine wireless.  This is especially true if the telephone uses spread spectrum technology. See caution at left.•  Wireless Video  Cameras:    Certain  wireless video cameras  (X10,  for  example) use the 2.4 GHz band.  These devices are also very low power and, in general, should not present a problem when using the SWM system.  See Section 5 Receiver Operation for methods of optimizing clear reception and minimizing interference. See caution at left. In the event problems still arise, see Section 5 Receiver Operation for methods of optimizing clear reception and minimizing interference.
14Sabine Smart Spectrum® Wireless© 2009  Sabine, Inc.4.  TRANSMITTER OPERATION4.1.  First stepBefore you begin, let’s look at a few basics regarding your transmitters.  The handheld mic is ready to go — the microphone and transmitter are combined in one unit.  To use the belt pack transmitter, however, you will have to con-nect a lavalier or headworn microphone (or instrument pickup) to its input.  Sabine lavalier and headworn mics, and Sabine’s guitar/instrument connec-tor (SW70G-TA4)  come equipped with the proper TA4F connector, and are ready to plug right in.  Be sure to line up the pins properly — do not force the connector into the belt pack.  If you are using a different microphone with the Sabine belt pack, please refer to the Appendix A for the required wiring plan.  Failure to use the proper wiring scheme may damage your mic or the belt pack, and void your warranty.Use the clip on the back of the belt pack transmitter to attach it to your belt or clothing.  The spring clip can be removed and reversed, to allow the trans-mitter and antenna to point either up or down in its clipped-on position. You can also remove the clip if you choose to keep the transmitter in your pocket.  NOTE: it is essential that transmitters retain a line-of-sight relationship with the receiver antennas.4.2.  Displays and SettingsYour Sabine Smart Spectrum handheld microphone and belt pack transmit-ter have many powerful features, all of which are easily monitored (using the transmitter LCD display) and adjusted. The  controls and  displays  for  both handheld and belt pack transmitters are almost identical in function, though positioning differs (compare figures 4b & 4c).  The LCD display and one control switch are located on the exterior of the transmitters.  A more powerful set of recessed controls is located under the hinged access panel, to prevent accidental or inappropriate alteration of settings.4.2.1.  LCD DisplayWhen the transmitter is first turned on, it shows an initial test screen (Fig. 4f), followed by the default screen (Fig. 4g). The LCD also reverts to this default display within a few seconds after any programming changes are made with the recessed controls. The default LCD display always shows transmission channel, audio level, and battery voltage level; additional information will appear to indicate important changes caused either by user adjustments, or automatically as transmitter status changes.Fig. 4aExternal SwitchFixedAntennaTA4F connectorBelt clip1. Select Button2. Up  Button3. Down Button4. Programmable Control of External Switch5. External Switch6. Recessed control and battery compartmentsFig. 4c SW65 & 75-T Transmitter Control Setting Buttons6Fig. 4b SW-H series Handheld Control Setting Buttons24513Transmitter Operation12346
15 Sabine Smart Spectrum® WirelessLIT-SWM6-7000-OG-EN-090215.indd - rr© 2009  Sabine, Inc.4.2.2.  Accessing Transmitter ControlsControl of all your transmitter functions is made using the Select button and the Up/Down buttons. These control buttons are located inside the access compartment on the beltpack or handheld transmitters.Opening the Beltpack Transmitter Access Compartment:1.  Using your thumb and forefinger, grab both tabs and simultaneously pull down toward the bottom of the beltpack.  This releases the locks.  2.  Gently pull the door open. Closing the Beltpack Transmitter Access Compartment:3.  Swing the door back up and close it by firmly pushing the top part of the door in until you hear the locks click.Opening the Handheld Transmitter Access Compartment:1.  Unscrew lower portion of the case.  Continue turning as you pull down.Closing the Handheld Transmitter Access Compartment:2.  Begin by turning the lower portion of the case as you push up.  When threads meet screw on until snug.NOTE: Do NOT attempt to unscrew the mic capsule from the body.  This will void your warranty!CHARGE:  Illuminates when the transmitter battery is being charged (i.e., when the charger is connected, either by direct plug-in or by placing the handheld mic in the Sabine charging clip).BATTERY VOLTAGE LEVEL METER: Indicates measured battery voltage; the more segments illuminated, the higher the voltage, and the greater the remaining battery life.AUDIO LEVEL METER: Shows the audio output level of the transmitter (affected by the pad setting).The last and largest segment indicates clip-ping.PARAMETER VALUE: In default mode this indicates the RF TRANSMIS-SION CHANNEL chosen for the transmitter.   In conjunction with the Select button (see figures 4b & 4c),  this field will also display battery run-time hours, or when a low frequency roll-off filter or an attenuation (pad) is ac-tive (see Fig. 4g).“TIME”: Displays when battery run-time hours are being displayed.“MUTE”: Indicates output is currently muted.“PAD”: Illuminates when the microphone pad is turned on. Use this if the audio meter shows clipping.“MIC”  INSTR”: Indicates SW65 & 75-T beltpack (only) is set to accept either mic or intrument input.“ON”:  Illuminates when either the audio and RF transmission, or the RF transmission only, are turned on. (SW-H Series only)“CHANNEL”: Illuminates in default mode to display transmission channel.Fig. 4f: Start up Transmitter LCD displaysTransmitter LCD Display IndicatorsFig. 4d: SW65 & 75-TFig. 4e: SW70-HTurn off transmitter before changing battery(s).BEFORE CHANGING BATTERYTransmitter Operation12312SW-H SeriesSW65 & 75-T
16Sabine Smart Spectrum® Wireless© 2009  Sabine, Inc.4.2.3.  Adjusting Transmitter SettingsDEFAULT/CHANNEL:  Press the Select button to enter Edit Mode, and repeat until the CHANNEL indicator flashes.  In this mode, the Up/Down buttons will adjust Transmission Channel.INPUT: (SW65 & 75-T Beltpack Transmitter only) Either “MIC” or “INSTR” for microphone or instrument.  You are required to choose the input in order to program both the transmitter and the receiver to optimize the input settings.  Choosing MIC automatically selects the 75 Hz roll-off filter.  You can choose to remove that but the extended low frequency response of the SW65 & 75-T may reproduce too much low energy for your system, so beware.  Choosing INSTR automatically removes the 75 Hz roll off filter for that added bottom end in your instruments.  NOTE: You can manually change that filter setting as needed.Electric Guitar/Bass & FBX: For best results, when using the SW65 & 75-T Beltpack Transmitter for electric guitar or bass, put your receiver’s FBX Feedback Exterminator into BYPASS mode. FBX BYPASS is acces-sible via the receiver front panel or Remote Software control.PAD:  Transmitter PAD setting. Press the Select button until the PAD indicator flashes. The Up/Down buttons will adjust attenuation (SW-H Series) 0, -6, -14, -20 dB; SW65 & 75-T: 0, -3, -6, -10, -14, -17, -20, -23, -26, -30, -34, -37, -40 dB).  When any level of attenuation is programmed, the default screen will illuminate PAD. See margin notes on this page and p.15 for settings instructions.TIME:  Battery Run-Time Hours.  Selecting this option changes the display to indicate the length of power-on time (hours and minutes) since the last battery change or recharge.NOTE: Battery run-time hours will reset when the transmitter (with battery in place) is connected to a charger. In the case of the charger, run-time hours will not start again until the charger is disconnected. You can manually reset the run-time hours by pressing both the up and down arrows. Use this to count hours when you use alkaline batteries.LOW FREQUENCY ROLL-OFF:  Selecting this option adds a 12 dB/octave low frequency roll-off filter, starting at 75 Hz, to the audio output of the transmitter. A roll-off filter may help reduce microphone handling noise, or other unwanted low frequency content. Pressing the Up or Down button toggles between the conditions of no filter (indicated in the display as L 0) or low roll-off (indicated by L 75).INTERNAL  CONTROL OF  EXTERNAL  SWITCH: The recessed  controls include a  3-position  switch,  which  in turn  determines how  the transmitter’s external two-position switch behaves (see figures 4a, 4b & 4h). From left-to-right, the 3 positions of the internal switch correspond to the following external switch operations: Transmitter OperationTransmitter LCD Display CyclePressing the Parameter Select button cycles the LCD through each of the editable functions on the transmitter. Individual screens appear for approximately 4 seconds, during which the function is editable.  The LCD for the SW65 & 75-T is shown.  The LCD for the SW-H Series displays the same information in a different layout.  See the previous page for a comparative look at both LCDs. Fig. 4gChannel Select Battery Run-Time DisplayPAD Select Low CutFig. 4h - Programmable Control of External SwitchProgrammable External SwitchHandheld MicrophonePAD SettingsYour  new Sabine  wireless  handheld  micro-phone is designed to accept a wide range of input levels, from spoken word all the way up to screaming vocals.  In order to accommodate this broad range of inputs, the transmitter has a PAD  setting.    Handheld  mics are  set to  a factory default of -14 dB, which is the preferred setting for concert vocal performance.If you need more output out of a microphone  (the receiver LCD audio meter shows the mic output level) then change the PAD settings as described below. When any level of attenua-tion is  programmed,  the  default  screen  will illuminate PAD.Transmitter PAD Adjustment(See Fig. 4b, 4f & 4g)1. Use the Transmitter Select button to scroll through functions until PAD flashes in the Transmitter LCD.2. Use the Up or Down buttons to select the desired setting. Selection is stored after 3 seconds of inactivity.3. Check to see if the receiver’s Audio Level Meter stays out of the Clipping Zone.InputSelectSuggested PAD SettingsPADVenueSpeech  0 dBLoud speech& vocal performance  -6 dBStrong vocalperformance (default)  -14 dBVery strong vocalperformance  -20 dBNOTENOTEGuitar Cord Simulator (Beltpack Transmitter Only)This feature allows you to fine tune the sound of your instrument while it is patched into your Sabine wireless beltpack.  For instructions please refer to page 22.(SW75-T only)
17 Sabine Smart Spectrum® WirelessLIT-SWM6-7000-OG-EN-090215.indd - rr© 2009  Sabine, Inc.1.  ON/OFF.   In internal position #1, the  external switch acts as a typical on/off switch.  Use this setting if you trust the microphone user to switch the microphone on and off as needed, and/or wish to conserve transmitter battery life during down times.  In the ON position the transmitter  LCD will display ON.  Both audio and RF are on.  In the OFF position the LCD ON is no longer illuminated.  Both RF and audio are off, and the battery run-time hours meter is off.  Note that Sabine’s squelch system prevents any “popping” when switching the transmitter on and off.  However, this protection causes a very short “power-on”  delay in the reactivation of the audio when the external switch is turned from OFF to ON.2.  ON/MUTE.  In internal position #2, the external switch acts as a typical mute switch.  Use this setting if you trust the microphone user to switch the microphone audio output on and off as needed; it will not conserve battery life in MUTE condition, but will allow the receiver to monitor and display the RF signal strength in either switch position. In the on position the default LCD will display ON.  Both audio and RF are on.  In the off position the word MUTE is displayed in the LCD.  The audio is muted but the transmitter is still transmitting the RF signal, and the battery run-time meter is running. There are no audible  pops when switching the transmitter between MUTE and ON. Switching from MUTE to ON will instantaneously pass audio signal (there will be NO delay as with internal position #1).3.  ON/ON.    In  internal  position  #3,  the external  switch is  disabled.   The transmitter (both RF and audio) is always on, and the word ON is always displayed in the transmitter  LCD screen.  Use this setting if you do not want to allow the speaker or performer to turn off the transmitter, or are worried that a transmitter may be accidentally turned off.  Caution:  When your program is over we suggest you move this switch to another setting so you can turn off the transmitter and save your battery.  You may also elect to remove the battery (though replacing the same one will restart the run-time meter and affect its accuracy accordingly).   Once you have completed the transmitter setup, you are ready to work with your receiver (see Section 5).  First, however, let’s talk about the issues and solutions concerning the source of transmitter power: the battery.4.2.4.  Transmitter Battery Management4.2.4.1.  Battery problems and Sabine solutionsRechargeable Battery memory.  Batteries that are repeatedly recharged prior to a complete discharge may fail more quickly in subsequent uses.  This problem is usually  referred  to as “battery  memory.”    Fortunately, Sabine’s innovative Tireless Wireless™ Charger takes steps to avoid this problem, by automatically reconditioning the battery whenever its intelligent diagnostics determine this is appropriate.  Sabine’s Tireless Wireless™ Charger will insure maximum life per battery charge, and also prolong the useful multiple-charge life span of rechargeable batteries.Battery  life.   Both  handheld  and  beltpack transmitters can  work  with disposable alkaline, disposable heavy-duty (manganese dioxide-carbon zinc), or rechargeable Nickel Metal Hydride (NiMH) batteries. We specifi-cally caution against using NiCad rechargeables due to well-known battery memory problems, and specifically recommend using the Sabine-supplied SWBAA2 (AA for the H1 Series handhelds and beltpack) batteries.  The rechargeable SWBAA2  batteries  will  last about 8  hours  per  recharge (typically, alkaline AA batteries will last about 10 hours). NOTE: Heavy-duty batteries will fall somewhere in the middle, between rechargeables and alkalines.Transmitter OperationBeltpack TransmitterPAD SettingsThe SW65 & 75-T beltpack transmitter has a broad range of PAD settings, which allow you to use it with almost any microphone or instru-ment. As in all audio equipment, the setting of the input level is crucial to achieving the best sound quality. Setting minimal PAD levels (-3, -6, or -10 dB) may produce a distorted sound if you are using a high output microphone or in-strument. Conversely, setting a more extreme PAD level  (-40,  -37,  or  -34  dB)  may require you to raise your system gain unnecessarily, resulting in a noisier output.  Watch the input meter on either the transmitter or the receiver (see illustrations) and set your level so there are at  least  three  indicators  illuminated for normal program level, with an occasional move to the  fourth indicator. The  fifth and  biggest indicator denotes clipping – watch out! If you see clipping, choose a lower pad setting (for example, from -10 to -14 dB).Transmitter PAD Adjustment(See Fig. 4c, 4f & 4g)1. Use the Transmitter Select button to scroll through functions until PAD flashes in the Transmitter LCD.2. Use the Up or Down buttons to select the desired setting. Selection is stored after 3 seconds of inactivity.3. Check to see if the receiver’s Audio Level Meter stays out of the Clipping Zone.Suggested PAD SettingsPADVenueLow output microphones  -10 dBStandard mics; acousticinstruments with low-gainpickups  -17 dBElectric guitars with low-gain pickups & mics withhigher gain  -23 dBMost standard electricguitars  -26 to -34 dB  Instruments with high-gain pre-amps  -37 dBSee the Transmitter Quick Guide that came with your transmitter for a complete look at the sug-gested pad settings. Default pad setting is -30 for SW65 & 75-T.
18Sabine Smart Spectrum® Wireless© 2009  Sabine, Inc.Sabine rechargeable battery advantages.  Here are several more good reasons why you can feel more confident about using rechargeable bat-teries:1.  All transmitters report two types of battery status information.  The first report is the all-important voltage the battery is supplying. Second, you’ll know how long the battery has been in use (battery run time hours).  Each receiver channel also receives telemetry information from its associated transmitter, regarding the battery voltage, and displays the information in the receiver LCD (see  figure 5b).  When the voltage reaches a level  indicating an estimated 30 remaining minutes of useful battery life, both transmitter and receiver automati-cally flash warnings in their LCD displays. As an alternative means of anticipating battery depletion, you can check the number of hours of use, by checking the transmitter LCD display (see Section 4.2.2 and figure 4g), or the Remote Control Software.2.  The handheld microphone clip that we provide with each handheld transmitter not only holds the microphone — it also can double as an unobtrusive charger housing.  Anytime the mic is parked in the clip (and the clip is connected to the charger power supply), the mic is being  charged.   As  an additional  safety  margin  against battery failure, the mic placed in the powered clip gets its power from the charger, not the battery, so it will work perfectly even if the battery is completely dead.3.  Sabine’s  intelligent charger circuitry detects the type of  battery  in place within the battery compartment, and automatically turns  off the charger if the battery is not compatible with the charger.4.  The Tireless Wireless™  Charger  detects  when a  battery  is  fully charged, and turns off the charging cycle.5.  The Tireless Wireless™ Charger prevents futile attempts to resus-citate dead batteries — if the battery is unresponsive, the charging cycle is stopped.6.  Beltpack and handheld batteries can be recharged without removing them from the transmitters. Just connect charger plug to the transmit-ter jack (see Fig. 4l).NOTE: In the “most discharged” battery condition, a full recharge may take up 8 to 12 hours depending on the mA value of the AA batteries used with the handheld and beltpack transmitter. The charging system will charge a batteries with a mA value of up to 2400.  When in doubt, charge the bat-teries overnight. Sabine’s battery-protection circuit will shut the charger down when charging is completed.Transmitter OperationTurn off transmitter before changing battery(s).BEFORE CHANGING BATTERYYour  Sabine True  Mobility®  transmitter comes with  one  or  more  rechargeable NiMH batteries.  For best results, charge the battery for at least 8 hours before using it for the first time.  Please note that the full charging potential of the bat-tery will be achieved after the first 5 charg-ing cycles have been completed.NiMH rechargeable batteries  are highly resistant to “memory effect,” which affects some other  rechargeable  batteries. The included NiMH batteries will provide more lifetime charges and longer battery life for each charge than many other recharge-able batteries.FIRST-TIME BATTERY CHARGING  NEDA: 14A  ANSI: 14A  IEC: LR14Alkaline batteries must be one of following types:SW70-H1, SW65- & 75-T Transmitters2 “AA” size (14.5x50.5mm,•  NiMH Rechargeable (Sabine part #: SWBAA2)•  Alkaline:  NEDA 14A   -   ANSI 14A   -   IEC LR14•  Heavy Duty batteries (NOT recommended))Acceptable Batteries for use withHandheld & Beltpack TransmittersIMPORTANT BATTERY INFORMATIONWARNING!   DO NOT USEAlkaline Rechargeable BatteriesAlkaline “AA”RechargeableBatteriesAlkaline Rechargeable
19 Sabine Smart Spectrum® WirelessLIT-SWM6-7000-OG-EN-090215.indd - rr© 2009  Sabine, Inc.4.2.4.2.  Charging Your BatteriesEquipment Connections.  Each SW65- & 75-T or SW-H Series trans-mitter comes equipped with an SWC-POWR Tireless Wireless™ plug-in charger (see Fig. 4l). In addition, each SW-H comes with its own battery-charging mic clip (SWC70-CL). The SWC-POWR charger can be plugged directly into either the transmitter or into the clip.  A Sabine rechargeable battery (SWBC1) will charge whenever the mic clip is connected to the Sabine SWC-POWR charger and the handheld is properly placed within the mic clip.Charging Indicators.  Much like your cell phone, the transmitters will let you know the charging status of the battery. When the battery is charg-ing, the battery meter will flash to indicate the relative level of the charge — one, two, three or four elements will flash (see Fig. 4i).Once the battery is fully charged, all four elements in the battery meter will flash. This indicates that the charging circuit is no longer on (see Fig. 4j). NOTE: The right-side indicator segment will flash for several minutes when charging is first attempted (see Fig. 4h). The lower the battery level, the longer this initial “testing/not charging” flashing sequence will continue. During this time, the Tireless Wireless battery circuit is evaluat-ing the suitability and charge status of the battery in place. When it has completed its evaluation, it will either commence the progressive flashing depicted in figure 4i (CHARGING), or continue to flash (TESTING/NOT CHARGING). All segments flashing in unison signifies that the battery is fully charged (see Fig. 4j).These same indications will also be displayed on the receiver LCD, and on the Remote Control Software screen.NOTE: The Tireless Wireless battery charger will only charge NiMH rechargeable batteries.  If  you place  any other  kind  of  battery  in the transmitter, and then attempt to charge it by connecting the charger, the Tireless Wireless circuit will detect the type of battery and will not begin charging.   Again,  the battery  indicator on the  transmitter will flash  the right-side element indicating testing/no charging (see Fig. 4h). Battery Warnings.  When the transmitter battery voltage drops below a critical threshold, the battery icon (which normally displays the voltage level) will begin to flash. This will occur on the transmitter and receiver and is an indication that you need to replace the battery, or charge it by placing the handheld mic in the charger clip. NOTE: Microphone will still transmit audio  when  placed  in clip.  Alternatively,  you can  connect  the charger directly to the transmitter using the built-in charger jack located on the side of the beltpack transmitter and near the antenna on the handheld transmitter (see Fig. 4l). If the battery is not changed or recharged, the transmitter will eventually turn off (see Fig. 4k).Transmitter OperationFig. 4l: SWC-POWR plug-in charger for SW70 Series Transmitters & SWC70CL Mic ClipFig.  4h:    TESTING/NOT CHARGINGRight-side battery  indicator segment will flash to indicate that the  battery  is  being tested. This  occurs  prior to charging  a  NiMH  battery  and  whenever  a non-rechargeable battery is placed on charge. Charging is not occuring when indicator lights in this fashion.Fig. 4j:  FULL CHARGEBattery  indicator  segments will flash  in  unison  to  indi-cate that the battery is fully charged.NOTE: Battery  can be  left connected to the charger and will receive peri-odic maintenance charging.Fig. 4i:  CHARGINGBattery  indicator  segments will flash progressively start-ing from the relative charge state of  the  battery. This example depicts a fully dis-charged battery being charged. As the charge progresses, left-side segments will remain vis-ible as right side segments continue to flash, until all segments are visible. At that point, all segments will flash on and off in unison (see Fig. 4j).Fig. 4k:  Battery CHARGE LEVEL displaysNOTE: When the battery has reached a specific discharge level, the transmitter will  automatically  turn off, and  the  transmit-ter LCD will display the message at right.Very Low (Flashing)Very UsedPartially UsedFully ChargedSW65/75TSW70H1SWC70CL(Mic Clip for SW70H1)
20Sabine Smart Spectrum® Wireless© 2009  Sabine, Inc.5.  RECEIVER OPERATION5.1.  LCD Display. The receiver LCD display is shown below (Fig. 5b). Two-channel receivers feature two LCDs, one for each channel. The display provides a snapshot report of the condition of your wireless channel, including battery status information sent from the transmitter by telemetry.The right two-thirds of the display primarily shows status information regarding the condition of your receiver channel, as follows:Receiver OperationFig. 5a: SW72-R (SW62-R) front panelFig. 5b: Receiver LCD Compete Display Receiver LCD Status BarsRelative Position Indicator Function Value DisplayFunction Display MessagesFBX, Lock and Edit Status Indicators
21 Sabine Smart Spectrum® WirelessLIT-SWM6-7000-OG-EN-090215.indd - rr© 2009  Sabine, Inc.Receiver OperationDiversity Status: Either 1 or 2 is lit, showing the active antenna.RF Signal Strength Indicator:  Indicates presence of RF (from transmitter, or external sources) on the chosen reception channel.  The greater the number of illuminated icons, the stronger the RF signal detected.Compression Meter:  Shows the active gain reduction applied to the receiver channel’s audio output.Audio Level Meter:  Shows the audio input level (received audio signal).Battery Voltage Level Meter:  Indicates the battery voltage of the corresponding transmitter; the more segments are illuminated, the higher the voltage, and the greater the remaining battery life. Receiver LCD Status BarsFBX, Lock and Edit Status IndicatorsFBX Status:  SETUP is illuminated while the receiver is in SETUP MODE.   READY is the normal operational mode, indicating SETUP has been performed and FBX filters are active.  BYPASS indicates the audio signal is NOT going through FBX filters (but all other DSP processing is active).Front Panel Lock Status:  LOCK 1 indicates all front panel controls are locked to prevent intentional tampering, or accidental programming.  LOCK 2 indicates a subset of  controls  are  locked,  allowing selected  others  to  be adjusted  with software only.  Default LOCK 2 setting locks out all functions except FBX and Program Load.Edit Status:   In a 2-channel receiver, this field illuminates when the corresponding Channel Button is pushed, indicating Controls are assigned to this channel.Firmware Version:   Displays for 2 seconds  on power up;  shows the receiver firmware version.Transmitter Battery Low:  You have 15 minutes or less to change transmitter batteries.Mute:  Transmitter muted; the transmitter on/off switch is set to mute.Front Panel Locked:  Front Panel is locked and the selected function cannot be edited. See Appendix D for an explanation of front panel locking.De-Esser:  The De-Esser is actively reducing sibilance.Function Display Messages

Navigation menu