Samsung Electronics Co SIP007AFS00 ARTIK-0710 User Manual
Samsung Electronics Co Ltd ARTIK-0710
Contents
User Manual
ARTIK 7 User Manual
Model: SIP007AFS00
1. ARTIK 7 RF PART Circuit Description
1.1 ZIGBEE : EM3587(U10)
The Ember EM3587 is a fully integrated System-on-Chip that integrates a 2.4 GHz, IEEE 802.15.4-
2003-compliant transceiver, 64-bit ARM® Cortex-A53 microprocessor, flash and RAM memory,
and peripherals of use to designers of ZigBee-based systems.
64-bit ARM® Cortex-A53 processors
2.4 GHz IEEE 802.15.4-2003 transceiver & lower MAC
256 or 512 kB flash, with optional read protection
32 or 64 kB RAM memory
AES128 encryption accelerator
Flexible ADC, UART/SPI/TWI serial communications, and general purpose timers
Optional USB serial communications
24 highly configurable GPIOs with Schmitt trigger inputs
1.2 WLAN/BT : BCM43455(U8)
BCM43455 is the combo module for IEEE 802.11 a/b/g/n/ac Wireless LAN and Bluetooth 4.1 + LE
at embedded and mobile applications. Wireless local area network (WLAN) compliant with the
IEEE 802.11 b/g/n specification
WLAN - IEEE 802.11ac Draft compliant
Single-stream spatial multiplexing up to 433.3Mbps data rate
Supports 20, 40, and 80MHz channels with optional SGI (256 QAM modulation)
Full IEEE 802.11 a/b/g/n legacy compatibility with enhanced performance
Tx/Rx low-density parity check (LDPC) support for improved range and power efficiency
Bluetooth – Bluetooth 4.1 + Low Energy
Bluetooth Class 1 or Class 2 transmitter operation
Supports extened synchronous connections(eSCO), for enhanced voice quality by allowing for retransmission
of dropped packets
FM unit supports HCI for communication.
FM receiver : 65MHz to 108 MHz FM band;supports the European radio data systems(RDS) and the North
American radio broadcast data system(RBDS) standards.
(1) Description for 2.4GHz
Description
Frequency
2412 ~ 2472 MHz
DFS attestations
Client without radar detection capability
Frequency tolerance
802.11 b / g / n : ± 20 ppm
IEEE802.11 mode
b / g / n
Data rate
up to 300 Mbps defined by the IEEE 802.11 b/g/n
Channel Bandwidth
20MHz, 40MHz
DFS channel
Not Support
Ad-hoc/WiFi direct
Not Support
WiFi display
Not Support
Data Modulation
DSSS : CCK, BPSK, QPSK for 802.11b
OFDM : BPSK, QPSK,16QAM, 64QAM for 802.11g/n
(2) Description for 5GHz
Description
Frequency
5150 ~ 5350MHz, 5470~5825MHz
DFS attestations
Client without radar detection capability
Frequency tolerance
802.11 a / n /ac : ± 20 ppm
IEEE802.11 mode
a / n / ac
Data rate
up to 867 Mbps defined by the IEEE 802.11 a/n/ac
Channel Bandwidth
20MHz, 40MHz, 80MHz
Scan behavior
Not mentioned
DFS channel
Use DFS range, No ability of radar detection
Ad-hoc/WiFi direct
Not Support
WiFi display
Not Support
Data Modulation
OFDM : BPSK, QPSK,16QAM, 64QAM, 256QAM for 802.11a/n/ac
(3) Description for Bluetooth
Description
Frequency
2402~2480
Power Class
Class 1 or 2
Bluetooth Standard
Bluetooth 4.1 + EDR
Data rate
up to 3Mbps defined by the Enhanced Data Rate
Data Modulation
FHSS : GFSK, OQPSK, 8DPSK, π /4DPSK for Bluetooth
2. ARTIK 7 Baseband Circuit Description
2.1 AP : S5P6818(U1)
Nexell S5P6818 is a system-on-a-chip (SoC) based on the 64-bit RISC processor for Smartphone
tablet, laptop, and desktop PCs. Designed with the 28 nm low power process, Nexell S5P6818
provides the best performance features such as CORTEX-A53 Octa core CPU, highest memory
bandwidth, Full HD display, 1080p 60 fps (frames per second) video decoding and 1080p 30
frame encoding hardware, 3D graphics hardware and high-speed interfaces such as eMMC4.5,
and USB 2.0.
ARM Cortex-A53 Octa CPU as high performance processor
- 64KB RAM, 20KB ROM and 512KB L2 Cache
Supports ARM TrustZone technology
Supports Security functions (AES, DES/TDES, SHA-1, MD5 and PRNG) and Secure JTAG
High Performance 3D Graphic Accelerator
Supports Dual Display up to 1920x1080, TFT-LCD, LVDS, HDMI 1.4a, MIPI-DSI and CVBS output
Supports various boot modes including NAND (with ECC detection and correction), SPI Flash/EEPROM,
NOR, SD(eMMC), USB and UART
2.2 Memory : KLM4G1FEPD-B031 (U2)
The Samsung KLM4G1FEPD-B031 is a 4 GB eMMC flash memory
embedded MultiMediaCard Ver. 5.0 compatible. Detail description is referenced by JEDEC Standard
SAMSUNG eMMC supports features of eMMC5.0 which are defined in JEDEC Standard
- Supported Features : Packed command, Cache, Discard, Sanitize, Power Off Notification, Data Tag,
Partition types, Context ID, Real Time Clock, Dynamic Device Capacity, HS200, HS400,Field Firmware
Update
- Non-supported Features : Large Sector Size (4KB)
Full backward compatibility with previous MultiMediaCard system specification (1bit data bus, multi-eMMC
systems)
Data bus width : 1bit (Default), 4bit and 8bit
MMC I/F Clock Frequency : 0 ~ 200MHz
MMC I/F Boot Frequency : 0 ~ 52MHz
Temperature : Operation (- -
Power : Interface power → VDD(VCCQ) (1.70V ~ 1.95V or 2.7V ~ 3.6V) , Memory power → VDDF(VCC)
(2.7V ~ 3.6V)
2.3 PMIC : S2MPS11B02(S2MPS11B2) (U4)
S2MPS11 is an advanced Power Management IC (PMIC) designed for mobile applications.
S2MPS11, coupled with Multi Core Samsung Application Processors (Exynos5410), is used in a
wide variety of mobile applications such as smart phones and tablet PCs.
I2C-Bus interface @3.4MHz and 400kHz
High Efficiency Step-down DC/DC Converters
Low Drop Voltage Regulators
USB External device interface
5ch-GPIO
Real-Time Clock (RTC)
Package CSP0606-85(0.5mm pitch) or CSP0608-80(0.65mm pitch)
Process CMOS
2. ARTIK 7 Antenna Description
The antennas supplied with the ARTIK developer kit are of the following specifications.
Antenna type
Dipole Antenna
Antenna peak gain
+1.43dBi(2484MHz) / +0.91(5320MHz)
Frequency
2.4GHz, 5GHz (for Wi-Fi, BT, ZigBee)
Connector type
SMA-M
FCC (United States) Compliance Statement
Replacement antennas must be of the same type, must be of equal or less gain than an antenna
previously authorized under the same grant of certification (A3LATKM052000 for ARTIK 5), and
must have similar in-band and out-of-band characteristics (consult specification sheet for cutoff
frequencies). Any new antenna type, or higher gain antenna, approved under Part 15 requires a
Class II permissive change, and the requirements of § 15.203 must be met.
IC (Canada) Compliance Statement
This radio transmitter (649E-ATKM052000 for ARTIK 5) has been approved by Industry Canada to
operate with the antenna types listed above with the maximum permissible gain indicated.
Antenna types not included in this list, having a gain greater than the maximum gain indicated
for that type, are strictly prohibited for use with this device. (RSS-GEN clause 8.3)
DB2/ 30119155.1
DRAFT 04/12/16 5:16PM 4:05PM
MODULE DISCLOSURES – QUICK START GUIDE
FCC REGULATORY DISCLOSURES
This device complies with Part 15 of the FCC`s Rules. Operation is subject to the following two
Conditions: (1) This device may not cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause undesirable operation
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/ TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20cm between the
transmitter’s radiating structure(s) and the body of the user or nearby persons.
This module is intended for OEM integration. The OEM integrator is responsible for FCC compliance and
compliance with all applicable regulations including those for modular transmitters 47 C.F.R. 15.212.
The OEM product must comply with all applicable labeling requirements including those contained in 15
C.F.R. 15.19. The OEM is solely responsible for certification and testing and labeling of its own products.
In addition to any independently required labels, the OEM shall also affix to the outside of a device into
which the module is installed a label referring to the enclosed module. This exterior label should be
prepared in a legible font and permanently affixed and using the wording “Contains Transmitter Module
FCCID: [A3LSIP007AFS00]
The OEM is required to ensure that the end product integrates this module so as to maintain a minimum
distance of 20 cm between the equipment’s radiating structure(s) and the body of the user or nearby
persons. The OEM shall also advise its end user of this requirement as required by applicable rules.
The OEM shall require that the end user of its product be informed that the FCC radio frequency
exposure guidelines for an uncontrolled environment can be satisfied. The OEM shall further inform its
DB2/ 30119155.1
DRAFT 04/12/16 5:16PM 4:05PM
end user that any change or modifications to this module not expressly approved by the manufacturer
will void the warranty and the users’ authority to operate the equipment.
INDUSTRY CANADA REGULATORY DISCLOSURES
INDUSTRY CANADA STATEMENT
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s). L'opération est
soumise aux deux conditions suivantes:(1) cet appareil ne peut causer d'interférences, et
(2) cet appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un
mauvais fonctionnement de l'appareil.
INDUSTRY CANADA RADIATION EXPOSURE STATEMENT AND LIMITATIONS ON USE
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20 cm between
the radiator and your body. This equipment should be installed and must not be co-located or operating
in conjunction with any other antenna or transmitter.
This equipment is restricted to indoor use in the 5.15-5.25 GHz range. This equipment is not able to be
operated at 5600-5650. In the United States and Canada, only Channel 1~11 can be operated and these
channel assignments deal only with the 2.4 GHz range.
The end product must be labeled to display the Industry Canada certification number of the module.
“Contains transmitter module IC: 649E-SIP007AFS00”
Le dispositif d'accueil doivent être étiquetés pour afficher le numéro de certification d'Industrie Canada
du module.
Contient module émetteur IC : 649E- SIP007AFS00
DB2/ 30119155.1
DRAFT 04/12/16 5:16PM 4:05PM
EU REGULATORY DISCLOSURES
CE STATEMENT *
The following statement must be supplied with each product but can be printed in the user manual, the
packaging, or provided as a separated leaflet.
Hereby, Samsung declares that this IoT Module is in compliance with the essential requirements
and other relevant provisions of Article 3 of the R&TTE Directive 1999/5/EC, 2004/108/EC and
RoHS directive 2011/65/EU.
“The declaration of conformity may be consulted at [www.artik.io/]”