Samsung Electronics Co SLS-BU10G 4G LTE Network Extender 2 for Enterprise User Manual

Samsung Electronics Co Ltd 4G LTE Network Extender 2 for Enterprise Users Manual

a href="https://usermanual.wiki/Samsung-Electronics-Co" itemprop="url"> Samsung Electronics Co >

Users Manual

Product ContentsMounting ProcedureConnection Overview PrerequisitesEthernet and Backhaul (B/H) RequirementsFor optimum performance regarding backhaul bandwidth requirements and specific firewall settings, please refer to the online 4G LTE Network Extender 2 for Enterprise User Guide found at http://support.verizonwireless.com/clc/devices/index.html?p=SLS-BU10G&m.GPS SignalThe Network Extender requires a strong GPS signal from the provided indoor GPS antenna. For installation other than with the provided GPS antenna, please refer to the online 4G LTE Network Extender 2 for Enterprise User Guide.Placement The Network Extender can be installed vertically, horizontally, on a wall, floor or ceiling.Place the unit at least 10 feet away from products that generate electromagnetic radiation (e.g., microwave oven). 1. Identify a location for the Network Extender, central to users, but no more than 21 feet from an exterior window or wall to allow for a strong GPS signal. 2. Identify a power source for the Network Extender. 3. Follow device mounting, installation and power up steps. 1. Remove the holding tape that was attached to fix the ceiling clip.For general safety and precautions, see Product Safety and Warranty Information.Your 4G LTE Network Extender 2 for Enterprise contains the following components: Connecting GPS, Antennae, and Power Cables 1. Gently remove protective covers for the power, Ethenet, and LMT ports. 2. Connect the GPS antenna cable (indoor use only) to the GPS port of the Network Extender.Mounting Procedure (Continued) 2. Remove the ceiling clip from the mount bracket. 3. Place the mount bracket on the wall. Mark and drill 4 screws in the appropriate spots. 4. Use a hammer to insert 4 plastic anchors into the drilled holes on the wall. Align the inserted plastic anchors and the screw holes of the bracket. Fix the bracket to the wall by fastening four M4 x L28 screws. 5. Align the Network Extender with the 3 holes on the mount bracket and then turn clockwise to fix it in place.Note: For ceiling mount, please refer to the Network Extender Installation Manual.LAA NE for Enterprise QSG_10162017.indd 1-6 10/16/2017 9:50:11 AM
StartupThe following Status LED sequence will occur. Upon successful setup, the LED will blink green.Note: If the LED fails to turn green after one hour or is slower blinking orange (1 pulse per 3 seconds), consult the troubleshooting section in the online 4G LTE Network Extender 2 for Enterprise User Guide.No GPS SignalA triple red blinking LED indicates no GPS signal. Check the About Network Extender page in the Advanced Settings web interface, on the tabs for “Status and Alerts” or “GPS” to see the status of the GPS constellation.Is my wireless device connected to the Network Extender?Using the web interface, sign in and check the Connected Devices panel for indication of connected users.Cannot reach Network Extender GUI or locked out of device.Press the RESET button for 10 seconds to reset the system to factory default settings.Port DownIn the event of an alternating red/blue LED, please check the Advanced Settings web interface on the tab for “Status and Alerts”. Follow the appropriate steps in the 4G LTE Network Extender 2 for Enterprise User Guide.Where to go for help.For complete installation and operational information, please see the online 4G LTE Network Extender 2 for Enterprise User Guide at http://www.verizonwireless.com/NetworkExtender.Call Customer Care toll Free at 800-922-0204 or *611 from your Verizon Wireless mobile phone.• Antennae extension cables • Power over Ethernet (POE) Injectors and SwitchesSee the 4G LTE Network Extender 2 for Enterprise User Guide for full details.For a full list of optional accessories, please see the 4G LTE Network Extender 2 for Enterprise Installation Guide.SLS-BU10G EP68-00556A Revision 1Verizon 4G LTENetwork Extender 2for EnterpriseQuick Start GuideConnecting GPS, Antennae, and Power Cables (Continued) 3. Attach an Ethernet cable from your router or modem LAN port to the Network Extender B/H port for network connectivity. 4. Attach the power cable for the Network Extender. Automatic power up will begin. The power supply can be mounted on a wall, floor or ceiling using the supplied screws and anchors.Power OnAt startup, the Network Extender will conduct self-configuration. This may take between 30 - 60 minutes the first time the Network Extender turns on.© 2017 Verizon Wireless. All rights reserved. Verizon Wireless is a trademark of Verizon Trademark Services LLC.Accessing Advanced SettingsTo access advanced settings and manage the Network Extender, you can Sign In to the web interface by following the steps below: 1. Use a computer connected to the same LAN as the Network Extender. 2. Open a web browser and enter the IP address of the Network Extender. http://<ip address of network extender>. 3. Sign in using the default admin password: enterpriseFemtØFor more detailed information on changing the TCP/IPv4 settings of the laptop, please see the 4G LTE Network Extender 2 for Enterprise User Guide.TroubleshootingOptional AccessoriesLAA NE for Enterprise QSG_10162017.indd 7-12 10/16/2017 9:50:13 AM
EP68-00557A Printed in KoreaVerizon Wireless4G LTE Network Extender 2 for EnterpriseProduct Safety and WarrantyPlease read this manual before operating yourdevice and keep it for future referenceLAA NE for Enterprise PSW.indd 1 9/28/2017 10:46:57 PM
Download:
Mirror Download [FCC.gov]
Document ID3686411
Application IDToIo5FI/cSpfA+6HPQAUKg==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeYes
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize205.28kB (2565951 bits)
Date Submitted2017-12-20 00:00:00
Date Available2018-06-15 00:00:00
Creation Date2017-11-08 19:06:56
Producing SoftwareAdobe PDF Library 11.0
Document Lastmod2017-11-21 18:34:05
Document TitleUsers Manual
Document CreatorAdobe InDesign CC 2014 (Windows)
FCC ID Filing: A3LSLS-BU10G

Navigation menu