Samsung Electronics Co WIDT20R Wi-Fi Module User Manual

Samsung Electronics Co Ltd Wi-Fi Module manual

a href="https://usermanual.wiki/Samsung-Electronics-Co" itemprop="url"> Samsung Electronics Co >

manual

1. Introduction WIDT20R is a USB embedded module compliant with IEEE802.11n standard. The core chipset is from Ralink, part number is RT5572. 2. Hardware Architecture: 2.1 Main Chipset Information 2.2 Circuit Block Diagram The major internal components and external interfaces of WIDT20R are illustrated in Figure 1-1. Figure 1-1 WIDT20R Major Component and System Interface 3. Antennas Information Two SMD antennas supporting both TX & RX. Hz+VGO 8GPFGT 2CTVPWODGT0$&%%35DGLR7UDQVFHLYHU3$ 5DOLQN 57* Information for OEM integrator : The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user manual of the end product. The user manual which is provided by OEM integrators for end users must include the following information in a prominent location. “To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.” Label for end product must include “Contains FCC ID: A3LWIDT20R/ IC ID:649E-WIDT20R or “ A RF transmitter inside, FCC ID: A3LWIDT20R/ IC ID:649E-WIDT20R”. gThe major internal components and external interfaces of WIDT20R are illustrated in Figure 1-1. Figure 1-1 WIDT20R Major Component and System Interface 2.2 CircuitBlockDiagram+VGO8GPFGT2CTVPWODGT0$&%%35DGLR7UDQVFHLYHU3$ 5DOLQN 57* Information for OEMintegrator :The OEM integrator has tobe awarenot to provideinformation tothe end user regarding how to install or removethis RFmodule inthe user manualof the endproduct. Thlhihiid dbOEMit tfdtildthfll iif tiiitlti1. Introduction WIDT20R is a USB embedded module compliant with IEEE802.11n standard. Thecore chipset is from Ralink, part number is RT5572. m2. Hardware Architecture: 2.1 Main Chipset Information The user manual which isprovidedby OEM integratorsfor end users mustinclude the followinginformation in a prominentlocation. “To complywith FCC RFexposure compliance requirements, theantennaused for this transmitter mustbe installedtoprovide a separationdistance of at least 20 cm from all persons and must notbe co-locatedor operatinginconjunction with any other antenna or transmitter.”Label for end product must include “ContainsFCC ID: A3LWIDT20R/ ICID:649E-WIDT20Ror “ A RF transmitter inside, FCC ID: A3LWIDT20R/ IC ID:649E-WIDT20R”.
4. Operational Description WIDT20R is the 802.11a/b/g/n RF Module, that acts as a communication hub for users of a wireless device to connect to a wired LAN. MIMO typeProduct type: WLAN (11b mode: 1TX, 1RX, 11g mode: 1TX, 1RX, n mode: 2TX, 2RX) Time base of the transmission frequencyFor IF and RF frequency, Crystal is a clock reference. SynthesizerSynthesizer inside Transceiver. Internal voltage controlled oscillator (VCO) provides the desired LO signal base on the phase-locked loop (PLL) with a relatively wide tuning range for this application.TransmissionBase-band Processing (BBP) IC has DSSS (BPSK/QPSK/CCK) and OFDM (BPSK/QPSK/16QAM/64QAM) modulation function, it provides transmission data rate are 1, 2, 5.5, 11 Mbps on DSSS and 6, 12, 18, 24, 36, 48, 54 Mbps on OFDM. Digital data signal will be converted to analog (TX IQ) signals through DAC in BBP IC, TX IQ pass through to low pass filter. TX I/Q signal use direct conversion (zero-IF) architecture converter to generate carrier frequency signal. Transceiver IC and internal PA magnify output power. ReceiverReverse direction isolation of LNA inside Transceiver IC suppresses unwanted radiation. Then RF signal will be directly down to IF signal (RX IQ) and high frequency spurious emissions are suppressed by LPF. At last RX IQ signal will be demodulated digital data. Base band Processing1. Channel selection is controlled by BBP IC to support data modulation: - DSSS (BPSK/QPSK/CCK) - OFDM (BPSK/QPSK/16QAM/64QAM) Power Control LevelIt uses closed-loop power control function to limit RF output power level. Transmit/Receive SwitchEUT has Transmit/Receive Switch and Antenna switch. End user can’t select any power setting. Channel Selection RestrictionFor product available in the USA/Canada/Taiwan market, only channel 1~11 can be operated. Selection of other channels is not possible. But product also could be available in the Europe/Japan market, channel 1~13 can be operated under the manufacturer change the different driver.Data Rate ControlThe operation date rate is changing during data transfer base on the optimization of driver. Discontinue Transmitting with absence of Data or operational failure states“The device shall automatically discontinue transmission in case of either absence of information to transmit or operational failure. These provisions are not intended to preclude the transmission
Download:
Mirror Download [FCC.gov]
Document ID1644231
Application IDNvXL7/GFTWDSfSA2lE+mfw==
Document Descriptionmanual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize26.81kB (335136 bits)
Date Submitted2012-02-27 00:00:00
Date Available2012-08-25 00:00:00
Creation Date2012-01-06 11:24:23
Producing SoftwareAcrobat Distiller 8.1.0 (Windows)
Document Lastmod2012-01-06 11:25:39
Document TitleMicrosoft Word - WiDT20R_Operation description.docx
Document CreatorPScript5.dll Version 5.2.2
Document Author: katie_gu
FCC ID Filing: A3LWIDT20R

Navigation menu