Savitech SA9800-A1 802.11b/g/n WiFi Module User Manual Hochleistungs

Savitech corp. 802.11b/g/n WiFi Module Hochleistungs

Contents

Users Manual

Model Name: SA9800-A1
802.11b/g/n Wireless Module
User Manual
Savitech Corp, 2014
Contents
Chapter 1
Introduction....................................................................
1
Chapter 2
Freatures.......................................................................
1
Chapter 3
Setting up SAVI9800.......................................................
2
Appendix
Regulatory Compliance Information.............................
3
SAVI9800
1
Chapter 1: Introduction
SA9800 is a wireless module. It is a hostless design and no extra host MCU
required for wireless speaker. The internal high speed processor can handle all
of network and audio functions. Auto group function let user easily set multiple
wireless devices into a group to make multi-room broadcasting.
Chapter 2: Features
2.1 Features
Built-in IEEE 802.11n 150 Mbps.
• USB 2.0 interface to connect hi-end USB audio SoC
•• UART for advance host command interface
• APP or web browser for easily configure
• Wakeup from WiFi
• OTA firmware upgrade
2.2 Wireless Spec
Wireless Specification
Feature
Detailed Description
Standard
IEEE 802.11 b/g/n One Path 2.4 GHz
Data Rate
Up to 150 Mbps
Security
WEP, WPA-PSK, WPA2-PSK
Antenna
I-PEX connector
Range
Up to 50 meter LOS
Storage
Temperature -40°C to +85°C
Operating
Temperature 0°C to +70°C
DC Input Voltage
3.3V +/- 10%
DC input Current
Max. 800mA @ 5V (Power Board)
Dimension
PCB
Board 60x40x1.6 mm
RF
Board (Shielding Case) 60x40x7.6 mm
2.3 Pin Definition
Pin
No.
Description
Pin
No.
Type
Description
1
VDD3.3V
16
I
RXIN
2
GND
17
O
TXON
3
USB_DM
18
G
GND
4
GND
19
I/O
I2S_WS
5
LED
20
I
I2S_SDI
6
FUNCTION LED
21
G
GND
7
GND
22
I
UART_RX
8
UART_TX
23
G
GND
9
GND
24
O
I2C_CLK
10
I2S_MCLK
25
I/O
I2C_DATA
11
I2S_SCK
26
I/O
Tack-SW
12
I2S_SDO
27
O
WLAN LED
13
GND
28
I/O
USB_DP
14
TXOP
29
G
GND
15
RXIP
30
P
VDD3.3V
2
2.3 The Status Lights
The LEDs is located in front panel, it can indicate some device information
LEDs
Status
Definition
LED 1
Off
unplugged
On
Power on
LED 2
Off
No connection. SA9800 is not set up or cannot establish a connection to the
network or the Internet
on
Network Ready
Flash
WAC mode
LED 3
Off
No definition
Flash
Show the status of client mode connecting to network. If connection is sucessful,
the LED will turn off, otherwise LED will keep flashing
on
Playing Music
LED 4
Flash
Wireless enable
n
Chapter 3: Setting up SA9800
Use SAVI9800 Utility on your computer or Wi-Fi settings on an iOS device to do one of
the following:
Set up your SAVI9800 Express to create a new network that wireless
computers and devices can use to connect to the Internet.
Set up your SAVI9800 Express to join an existing network. If the network is
connected to the Internet, all the computers and wireless devices on the SAVI9800
network can use the Internet connection. If the network is set up to be extended,
SAVI9800 can extend the range of that network.
You can do all of your basic network setup and configuration with the setup
assistant in SAVI9800 Utility on a Mac or Windows computer, or with Wi-Fi settings on
an iOS device. To manage your network and configure advanced options, see
“Setting Advanced Options”
System Requirements
To set up SAVI9800 Express using a Mac, you need: Mac computer with an WLAN
card installed.
Mac OS X v10.5.7 or later
Use Software Update to get the latest version of SAVI9800 Utility.
To set up SAVI9800 Express using a Windows PC, you need:
Windows computer with a 300 MHz or higher processor and Wi-Fi certified wireless
capability (to set it up wirelessly), or a Windows computer connected to the SAVI9800
with a WLAN network.
3
Setting up your SA9800
To set up SAVI9800 Express using a computer:
1. Connect to SAVI9800 through WLAN connection.
2. Open web browser(Safari, Internet explore or Google chrome)
3. Key in “192.168.6.1” to enter web setup
4. Follow the onscreen instructions for creating a new network or joining an
existing one.
Regulatory Compliance Information
CE Mark Warning:
This is a Class B product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
FCC Statement:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communication. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
4
IMPORTANT NOTICE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body. This transmitter must not
be co-located or operating in conjunction with any other antenna or transmitter.
FCC Alert Statement:
The availability of some specific channels and/or operational frequency bands are
country dependent and are firmware programmed at the factory to match the intended
destination. The firmware setting is not accessible by the end user.
Manual information to the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF
module in the user's manual of the end product which integrates this module.
The end user manual shall include all required regulatory information/warning as show
in this manual and the final end product
must be labeled in a visible area with the following: " Contains FCC ID : 2ABTG-
SA9800-A1.
The product is used dipole antenna and antenna Gain is 3.14 dBi.

Navigation menu