Scientech Electronics PIR3 PIR Motion Detector User Manual

Scientech Electronics Co., Ltd. PIR Motion Detector

a href="https://usermanual.wiki/Scientech-Electronics" itemprop="url"> Scientech Electronics >

User Manual

ACCESSORIES The LS-30 system includes a full range of accessories, so you can customize many feature of your security system. All the radio transmitters used in the LS-30 system, except the Remote Controller, have a unique random code that is set by the factory with 16,777,216 combinations in total. Also with specially designed transmission timing control, the LS-30 system can effectively prevent mutual interference from other transmitters in the system. The Remote Controller uses copy-preventing hopping-code technology, changing its radio code every time you press the button. The combinations possible through this hopping-code are up to 7.3 X 1019. To comply with the regulations in most countries, radio power is limited to below 10mW, and effective range is about 100 meters measured at open field. The range may be somewhat less indoors, depending on the layout of building construction and furniture. You may enroll all the wireless accessories and change their related settings, either through the guidance of the interactive LCD display on the Base Unit explained in the “INSTALLATION” section that follows, or by using a computer with the proprietary software “HyperSecureLink” through an interface adapter, which offers a quicker and simpler way to perform the installation in. NOTE: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The comply with the FCC RF exposure compliance requirements, this device and its antenna must not be co-located or operating to conjunction with any other antenna or transmitter. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
PIR MOTION DETECTOR INTRODUCTION The PIR-3SP Passive Infrared Detector detects the movement of human body heat within its effective coverage; thus, when an intruder crosses or enters the area, the resulting change in infrared energy from the intruder will be detected and an alarm signal will transmit to the Base Unit. PET IMMUNE DETECTOR  This detector is immune to one domestic pet up to 18 kg or 60 cm moving on the floor.  If animal activity takes place above 1 meter high, the pet immunity allowance will be significantly reduced. It is therefore recommended to select a mounting location that can avoid animal moving within 1.8 m of the detector.  This detector should be mounted on the wall or corner at 2.3 m high and perpendicular to the floor.  Do NOT use any mounting bracket with swivel adjustment. Should you must use a bracket, it should be used for horizontal alignment only, do not tilt down.  The weight of the animal can only be used as a reference. Other factors such as height and color of fur could also affect the level of immunity.  Do NOT aim the detector at stairways that animal can pass.  Place the PCB at the “P” scale position. And Jumper JP5 at “PET” position.  It’s a must to verify the pet immune function after installation. In case animal is detected, sliding the PCB to -1 or 0 scale to test again. IMPORTANT NOTE To get the best sensitivity, PIR should be mounted to detect movement of the intruder across a room rather than toward the detector. AAA BatteryX 2Tamper Switch LED ON/OFFJumper Pulse Count JumperTest SwitchReed SwitchPCB Scale Infrared Sensor(Don’t touch) PCB Fixing Screw Jumper JP5Fig. 1
Download:
Mirror Download [FCC.gov]
Document ID625824
Application IDGqqJGA6CSqsgykimaaDatQ==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize8.51kB (106425 bits)
Date Submitted2006-02-03 00:00:00
Date Available2006-01-31 00:00:00
Creation Date2006-01-19 10:59:09
Producing SoftwareAcrobat Distiller 6.0 (Windows)
Document Lastmod2006-01-19 11:15:26
Document Titleuntitled
FCC ID Filing: TYLPIR3

Navigation menu