Senao Networks AP102 Wireless 802.11abgn Access Point User Manual

Senao Networks, Inc. Wireless 802.11abgn Access Point AP102 QSG 032414

a href="https://usermanual.wiki/Senao-Networks" itemprop="url"> Senao Networks >

Contents

User Manual.pdf

Quick Start GuideWatchGuard® APAP102WatchGuard® Technologies, Inc.Guide de démarrage rapide Kurzanleitung Guida introduttivaGuía RápidaGuia de início rápido快速設定手冊
1. Loosen the two screws on the rear cover of the AP device and remove the cover.2. If you plan to use an AC power adapter, remove the plug from the right gasket opening. Then, connect the power adapter and push the cord into the right gasket opening. Note: If you use PoE, do not remove the plug from the right gasket opening.3. Connect an Ethernet cable and push the cable into the left gasket opening.4. Put the gasket cover over the gasket opening and push it in place.5. Replace the AP device cover and tighten the screws.6. Connect the other end of the Ethernet cable to your network.7. Connect your power supply.The device powers on. The light on the front of the device ashes amber while the device boots up and then changes to steady green when the device is ready.Assign an IP Address to the WatchGuard AP DeviceThere are two ways the WatchGuard AP device can get an IP address: • Automatic IP Address Conguration by DHCP - When rst powered on, the WatchGuard AP device automatically requests an IP address from a DHCP server on your network.• Manual IP Address Conguration - If you do not use DHCP on your network, you must directly connect to the WatchGuard AP device to assign a static IP address. To set the IP address on your WatchGuard AP device:• Connect an Ethernet cable from the AP device to your computer.• Congure your computer to use these settings: IP Address: 192.168.1.2, Subnet mask: 255.255.255.0, Gateway: 192.168.1.1.• Open a web browser and type https://192.168.1.1.• To log in to the WatchGuard AP web UI, type the default password: wgwap.• Set the IP address of the AP device to an IP address on the same network as your XTM device. Connect the WatchGuard AP DeviceEnglish1Pair the AP DeviceYou can now pair the WatchGuard AP device with a Firebox or XTM device.1. Use Policy Manager or the Fireware XTM Web UI to edit the Firebox or XTM device conguration.2. Select Network > Gateway Wireless Controller.3. Enable the Gateway Wireless Controller, and save the conguration to the Firebox or XTM device. 4. In the Gateway Wireless Controller conguration, on the Access Points tab, click Refresh to discover the AP device.5. Select the unpaired Access Point and click Pair.6. In the Pairing Passphrase dialog box, type the passphrase of the AP device. The default passphrase is wgwap.For detailed information about WatchGuard AP pairing, management, and conguration with your Firebox or XTM device, see the WatchGuard AP Device Setup section of the product Help at http:www.watchguard.com/help/documentation/xtm.asp2Package Contents• AP device and mounting kit• Quick Start Guide
Download:
Mirror Download [FCC.gov]
Document ID2238526
Application ID7aGFJ7+v/OLBTuujNEghaA==
Document DescriptionUser Manual.pdf
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize126.85kB (1585661 bits)
Date Submitted2014-04-10 00:00:00
Date Available2014-04-10 00:00:00
Creation Date2014-04-07 14:17:10
Producing SoftwarePDF-XChange Viewer [Version: 2.0 (Build 40.7) (Nov 25 2008; 17:31:42)]
Document Lastmod2014-04-09 14:35:18
Document TitleAP102_QSG_032414
Document CreatorAdobe InDesign CC (Macintosh)
Document Author: WatchGuard Technologies
FCC ID Filing: U2M-AP102

Navigation menu