Sercomm SZESW02N ZigBee Energy Switch User Manual

Sercomm Corporation ZigBee Energy Switch Users Manual

a href="https://usermanual.wiki/Sercomm" itemprop="url"> Sercomm >

Users Manual

SZ-E(B)SW02(N)  V0.4 SZ-ESW02N, SZ-ESW02, SZ-BSW02N Power on/off Switch Installation Guide This  is an electrical power measuring device, which is compatible with ZigBee enabled devices with its embedded radio frequency (RF) technology. It can also be used with other devices with the ZigBee logo regardless of the manufacturer. Furthermore, it can work as a signal repeater that will extend the wireless transmission range and increase the reliability of your network. With a ZigBee compatible gateway and software program, you’ll be able to monitor and inform the energy usage of the connected appliance.  Specification    Radio Frequency 2.4GHz LED Indicator Green x 1 Input Power 120V / 60Hz Max Load 15A Resistive / 400W Incandescent Operation Temperature 0° -  40°C (32° - 104°F) Storage Temperature -20° - 70°C (-4° - 158°F) Alarm Over voltage protection & Over current protection     Package Contents     SZ-ESW02(N) or SZ-BSW02N  ZigBee Energy Switch                                                                     Installation & Operation Manual                       Warnings and Cautions   •    Please install and/or use in accordance with appropriate electrical codes and regulations. •    If you are unsure about any part of these instructions, please consult a qualified electrician. •    To reduce the risk of overheating, do not install the device near heat sources, such as fires, boilers or heating vents. •    Do not locate the device facing direct sunlight or humid place. •    This instruction sheet contains important technical data. Please keep it for future reference.  LED   Power (Green)    On (Green) - Power On. Blinking (Green) - The join function is being processed.  Installation   NOTE: In order to use SZ-ESW02(N) or  SZ-BSW02N in a ZigBee network, the device must be connected to the network via ZigBee coordinator. Please refer to the instruction sheet for complete information. 1.    Put the SZ-ESW02(N) or SZ-BSW02N into a wall receptacle. Make sure the receptacle is working properly. If it is controlled by a wall switch, please ensure it is set to ON all the time.  2.    Attach the appliance to the SZ-ESW02(N) or SZ-BSW02N.
 SZ-E(B)SW02(N)  V0.4 Operation                            1. On/Off  and Pairing Button 2. On/Off , Pairing and alarm LED (Green)   MANUAL Operation: •    ON/OFF: Press this button of the device to turn the appliance on/off.  NOTE: The appliance will be turned Off  regardless of its previous setting.  Join / Leave Function  Auto Joining State: A sensor that does not have a network shall search for a network that is open for joining. 1. Illuminate the LED indicator for 2 seconds to indicate a successful boot.  2. The sensor should resume scanning the next time a user-trigger occurs. This allows user interaction to cause the sensor to      resume scanning.  Joined State: A sensor that has joined shall resume the network.          1. Illuminate the LED indicator for 2 seconds to indicate a successful boot.          2. Resume operation with the existing network.  Manual Defaulting: Default a sensor puts it into a state where it is ready to be joined to a coordinator.          The process for manually default a sensor shall be as follows:          1. With the sensor powered down, press the button and hold it.          2. Power it up again. The sensor should illuminate the LED once all boot up/initialization tasks are complete.          3. Release the button while the LED has been illuminated (in 4 seconds).          4. The sensor shall then wipe any knowledge of the previous network and other configuration parameters and begin searching  for a new network(Auto Joining State). Troubleshooting     If the device appears to be functioning improperly, please follow the suggested steps: 1. Confirm that the device is being supplied from a 120V power source. 2. Confirm that the device is being controlled in a proper way (local switch is ON). 3. Ensure that the appliance does not exceed 15A current.
Download:
Mirror Download [FCC.gov]
Document ID3209245
Application IDJmsgkOpmicEUtQdPcktDow==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize12.11kB (151399 bits)
Date Submitted2016-11-28 00:00:00
Date Available2016-11-28 00:00:00
Creation Date2016-11-10 14:38:09
Producing SoftwareMicrosoft® Office Word 2007
Document Lastmod2016-11-10 14:38:09
Document TitleSZ-ESW01-AU ZigBee Energy Switch Installation Guide
Document CreatorMicrosoft® Office Word 2007
Document Author: Alex Huang
FCC ID Filing: P27SZESW02N

Navigation menu