Servis Rhino Brush Cutter Fs15 Users Manual FS15,FS10 COVER.p65

FS15 to the manual 2b5a5326-a850-4986-9382-b6d49691de70

2015-02-02

: Servis-Rhino Servis-Rhino-Brush-Cutter-Fs15-Users-Manual-490774 servis-rhino-brush-cutter-fs15-users-manual-490774 servis-rhino pdf

Open the PDF directly: View PDF PDF.
Page Count: 84

FS15
FLEX-WING
ROTARY CUTTER
MASTER PARTS BOOK
S/N 00101 TO 10429
PARTS LISTING
Rhino
An Alamo Group Company
1020 S. Sangamon Ave.
Gibson City, Il 60936
1-800-446-5158
Email: parts@servis-rhino.com
© 2005 Alamo Group Inc.
®
Published 07-05 P/N 00773425MB
TO THE OWNER/OPERATOR/DEALER
All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who
recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to
be used with all its safety equipment properly attached to minimize the chance of accidents.
BEFORE YOU START!! Read the safety messages on the implement and shown in your manual.
Observe the rules of safety and common sense!
WARRANTY INFORMATION:
Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration Form
in full and return it within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Card
and on the Warranty Form that you retain. The use of "will-fit" parts will void your warranty and can cause catastrophic
failure with possible injury or death.
PARTS
SECTION
Parts Section – 1
Parts Section – 2
©2005 Alamo Group Inc.
For maximum safety and to guarantee optimum product reliability, always use
genuine Servis-Rhino Parts. The use of inferior replacement parts may cause
premature or catastrophic failure which could result in serious injury or death.
Direct any questions regarding parts to:
The following instructions are offered to help eliminate needless delay and error in processing
purchase orders for the equipment in this section.
1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the
basic machine featured in this manual. Part Numbers and Descriptions are given to help
locate the parts and quantities required.
2. The Purchase Order must include the name and address of the person or organization
ordering the parts, who should be charged, and if possible, the serial number of the machine
for which the parts are ordered.
3. The Purchase Order must clearly list the quantity of each part, the complete and correct part
number (be sure to include all periods), and the basic name of the part.
4. The Manufacturer reserves the right to substitute parts where applicable.
5. Some parts are unlisted items which are special production items not normally stocked and
are subject to special handling. Request a quotation for such parts before sending a
Purchase Order.
6. The Manufacturer reserves the right to change prices without prior notice.
NOTE: Please refer to The Safety Section in the front of this Manual for the proper
Part Number when ordering Replacement Safety Decals.
PARTS ORDERING GUIDE
RHINORHINO
RHINORHINO
RHINO®
1020 S. Sangamon Ave.
Gibson City, IL 60936
800-446-5158
Email: parts@servis-rhino.com
PART NAME INDEX
AXLE ASSEMBLY - CTR & WING S/N 00101 - 10147 OCT 1977 - JAN 1988.................................................................... 5
AXLE ASSEMBLY - CTR & WING S/N 10148 - 10429 JAN 1988 - MAY 1988.................................................................... 6
BLADE BAR ASSEMBLY - CTR HEAVY DUTY S/N 01162 - 10429 DEC 1980 - MAY 1988.............................................. 7
BLADE BAR ASSEMBLY - CTR STANDARD S/N 00101 - 01162 OCT 1977 - DEC 1980 ................................................. 8
BLADE BAR ASSEMBLY - WING HEAVY DUTY S/N 01162 - 10429 DEC 1980 - MAY 1988 ........................................... 9
BLADE BAR ASSEMBLY - WING STANDARD S/N 01162 - 10429 OCT 1977 - DEC 1980............................................. 10
BLADE PAN ASSEMBLY - CTR HEAVY DUTY S/N 01162 - 10429 DEC 1980 - MAY 1988............................................ 11
BLADE PAN ASSEMBLY - CTR STANDARD S/N 00101 - 01162 OCT 1977 - DEC 1980 ............................................... 12
BLADE PAN ASSEMBLY - WING HEAVY DUTY S/N 01162 - 10429 DEC 1980 - MAY 1988 ......................................... 13
BLADE PAN ASSEMBLY - WING STANDARD S/N 00101 - 01162 OCT 1977 - DEC 1980............................................. 14
CHAIN GUARD - CENTER & WING SECTION S/N 01497 - 10429 JUN 1982 - MAY 1988 ............................................. 15
CHAIN GUARD - REAR CENTER SECTION S/N 01497 - 10429 JUN 1982 - MAY 1988................................................. 16
CHAIN GUARD - REAR WING SECTION S/N 01497 - 10429 JUN 1982 - MAY 1988...................................................... 17
CYLINDER ASSEMBLY - CENTER AXLE S/N 00101 - 01377 OCT 1977 - JAN 1982...................................................... 18
CYLINDER ASSEMBLY - CENTER AXLE S/N 00101 - 10429 OCT 1977 - MAY 1988..................................................... 19
CYLINDER ASSEMBLY - CENTER AXLE S/N 01376 - 10429 JAN 1982 - MAY 1988 ..................................................... 20
CYLINDER ASSEMBLY - LEVEL LIFT - 2-1/2 X 8 SLAVE CYL S/N 00101 - 10429 OCT 1977 - MAY 1988................... 21
CYLINDER ASSEMBLY - LEVEL LIFT - 2-3/4 X 8 SLAVE CYL S/N 00101 - 10429 OCT 1977 - MAY 1988................... 22
CYLINDER ASSEMBLY - LEVEL LIFT - 3 X 8 SLAVE CYL S/N 00101 - 10429 OCT 1977 - MAY 1988......................... 23
CYLINDER ASSEMBLY - LEVEL LIFT REPLACEMENT ASSY (P/N 8719) S/N 00101 - 10429 OCT 1977 - MA............ 24
CYLINDER ASSEMBLY - LEVEL LIFT REPLACEMENT ASSY (P/N 8720) S/N 00101 - 10429 OCT 1977 - MA............ 25
CYLINDER ASSEMBLY - LEVEL LIFT REPLACEMENT ASSY (P/N 8721) S/N 00101 - 10429 OCT 1977 - MA............ 26
CYLINDER ASSEMBLY - WING-HYDRAULIC CYLINDER & HOSE GROUP S/N 00101 - 01376 OCT 1977 - JAN ....... 27
CYLINDER ASSEMBLY - WING-LANTEX HYDRAULIC CYL & HOSE GRP S/N 01377 - 10429 JAN 1982 - MAY......... 28
CYLINDER ASSEMBLY - WING-REPLACEMENT S/N 00101 - 10429 OCT 1977 - MAY 1988........................................ 29
DECALS S/N 00101 - 10429 OCT 1977 - MAY 1988.......................................................................................................... 30
DEFLECTOR - REAR WING S/N 01497 - 10429 JUN 1982 - MAY 1988 .......................................................................... 31
DEFLECTOR - RUBBER FRONT CENTER S/N 00101 - 10429 OCT 1977 - MAY 1988 .................................................. 32
DEFLECTOR - RUBBER FRONT WING LEFT & RIGHT S/N 00101 - 10429 OCT 1977 - MAY 1988 ............................. 33
DEFLECTOR - RUBBER LEFT & RIGHT CENTER S/N 00101 - 10429 OCT 1977 - MAY 1988...................................... 34
DRIVELINE ASSEMBLY - CTR GEARBOX SQUARE SHAFT SLIP 35R S/N 00101 - 10429 OCT 1977 - MAY 19......... 35
DRIVELINE ASSEMBLY - OUTBOARD SQUARE SHAFT ASSEMBLY 35R S/N 00101 - 10429 OCT 1977 - MAY 1..... 36
DRIVELINE ASSEMBLY - PTO SQUARE SHAFT ASSEMBLY 44R S/N 00101 - 10429 OCT 1977 - MAY 1988............ 37
DRIVELINE ASSEMBLY - SHIELDING ASSEMBLY SQUARE SHAFTS S/N 00101 - 10429 OCT 1977 - MAY 198 ....... 38
GEARBOX ASSEMBLY - CENTER SECTION S/N 00101 - 10429 OCT 1977 - MAY 1988 .............................................. 40
GEARBOX ASSEMBLY - DIVIDER (COMER) S/N 01901 - 10429 FEB 1985 - MAY 1988 ............................................... 42
GEARBOX ASSEMBLY - DIVIDER S/N 00101 - 01900 OCT 1977 - FEB 1985 ................................................................ 44
GEARBOX ASSEMBLY - LEFT WING S/N 00101 - 10429 OCT 1977 - MAY 1988 .......................................................... 46
GEARBOX ASSEMBLY - RIGHT WING S/N 00101 - 10429 OCT 1977 - MAY 1988........................................................ 48
GEARBOX ATTACHMENT - DIVIDER & CENTER GEARBOX S/N 00101 - 10429 OCT 1977 - MAY 1988.................... 50
GEARBOX ATTACHMENT- RIGHT & LEFT WING GEARBOX S/N 00101 - 10429 OCT 1977 - MAY 1988 ................... 51
HOSE BRACKET COMPONENTS S/N 00101 - 10429 OCT 1977 - MAY 1988................................................................. 52
HUB ASSEMBLY - CENTER & OUTBOARD S/N 10148 - 10428 JAN 1988 - MAY 1988 ................................................. 53
HUB ASSEMBLY - OUTBOARD AXLES S/N 00101 - 10147 OCT 1977 - JAN 1988 ........................................................ 54
HUB ASSEMBLY - STANDARD CENTER AXLE S/N 00101 - 10147 OCT 1977 - JAN 1988 ........................................... 55
HYDRAULIC CONTROL VALVE MOUNTING KIT S/N 00101 - 10429 OCT 1977 - MAY 1988 ........................................ 56
HYDRAULIC HOSE ADAPTERS S/N 00101 - 10429 OCT 1977 - MAY 1988 ................................................................... 57
HYDRAULIC VALVE ASSEMBLY - DETENT W/SPRING ASSEMBLY S/N 00101 - 10429 OCT 1977 - MAY 1988........ 58
HYDRAULIC VALVE ASSEMBLY - OPEN/CLOSED CENTER VALVE S/N 00101 - 10429 OCT 1977 - MAY 1988........ 59
JACK ASSEMBLY - TOP WING S/N 00101 - 10429 OCT 1977 - MAY 1988 .................................................................... 60
LEFT SCREW S/N 00101 - 10429 OCT 1977 - MAY 1988................................................................................................. 61
LEVEL LIFT KIT FIELD INSTALLATION S/N 00101 - 10429 OCT 1977 - MAY 1988 ....................................................... 62
LEVEL LIFT ROD ASSEMBLY S/N 10148 - 10428 JAN 1988 - MAY 1988 ....................................................................... 63
MAINFRAME ASSEMBLY S/N 00101 - 01900 OCT 1977 - FEB 1985............................................................................... 64
MAINFRAME ASSEMBLY S/N 01901 - 10429 FEB 1985 - MAY 1988 .............................................................................. 65
NOTES.................................................................................................................................................................................. 39
SIDE SHOE & SIDE SKIRT - OFFSET MODELS CTR SECTION S/N 00101 - 10429 OCT 1977 - MAY 1988................ 66
SIDE SHOE & SIDE SKIRT S/N 00101 - 10429 OCT 1977 - MAY 1988 ........................................................................... 67
SKID SHOE ASSEMBLY S/N 00101 - 00466 OCT 1977 - FEB 1979 ................................................................................ 68
SKID SHOE ASSEMBLY S/N 00101 - 10429 OCT 1977 - MAY 1988................................................................................ 69
SPRING ASSEMBLY - CENTER AXLE S/N 00101 - 10429 OCT 1977 - MAY 1988......................................................... 70
SPRING ASSEMBLY - WING S/N 00101 - 10429 OCT 1977 - MAY 1988 ........................................................................ 71
TIRE/WHEEL ASSEMBLY S/N 00101 - 10429 OCT 1977 - MAY 1988 ............................................................................. 72
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 3
PART NAME INDEX
TONGUE ASSEMBLY S/N 00101 - 10429 OCT 1977 - MAY 1988.................................................................................... 73
TORQUE LIMITER ASSEMBLY S/N 00101 - 10001 OCT 1977 - AUG 1987..................................................................... 74
TORQUE LIMITER ASSEMBLY S/N 10001 - 10429 AUG 1987 - MAY 1988 .................................................................... 75
WEIGHT BOX S/N 00101 - 10429 OCT 1977 - MAY 1988................................................................................................. 76
WINCH AND STAND ASSSEMBLY S/N 00101 - 10429 OCT 1977 - MAY 1988............................................................... 77
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 4
AXLE ASSEMBLY - CTR & WING S/N 00101 - 10147 OCT 1977 - JAN 1988
ITEM PART NO. QTY. DESCRIPTION
1 0656060100 1 CENTER AXLE WELD NOT SHOWN
0656280100 1 DOUBLE AXLE WELD SHOWN
5 0656070110 1 AXLE WLD R.H. ONLY
0656070100 1 AXLE ASSY
6 0656070210 1 AXLE WLD L.H. ONLY
0656070200 1 AXLE ASSY
7 20BH5012 4 PIN-SPIRAL 5/16 X 1 1/2 *
8 15B1600 4 WASHER 1 SAE P *
9 65106A4 4 WLDMT,AXLE PIVOT PIN *
10 D121 1 DECAL ADJ-NUTS
11 D301 1 DECAL,RHINO
15 0652140220 1 WLDMT, AXLE ARM - LEFT **
0652140210 15 LEFT AXLE ASSY **
16 0652140260 1 WLDMT, AXLE ARM - RIGHT
0652140250 1 RIGHT AXLE ASSY **
Note: This Axle uses hub #3741247 assembly on center and hub #271033 assembly on wing. Washers are welded to
spindle on center axle but not on the wing.
FOR REPLACEMENT PARTS ONLY
*QTY SHOWN FOR 1 MACHINE, COMPLETE
**USED W/FACTORY LEVEL LIFT ONLY ITEM #15 AND #16
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 5
AXLE ASSEMBLY - CTR & WING S/N 10148 - 10429 JAN 1988 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
1 00756458 1 AXLE CENTER ASSY NOT SHOWN
00756456 1 AXLE DOUBLE CENTER SHOWN
2 00756461 1 AXLE ARM ASSY (R.H.), COMPLETE W/1 HUB
3 00756464 1 AXLE ARM ASSY(L.H.), COMPLETE W/1 HUB
4 00756455 1 DOUBLE AXLE ARM WELD SHOWN
00756457 1 CENTER AXLE WELD NOT SHOWN
5 00756459 1 AXLE WELD (R.H.) ONLY
6 00756462 1 AXLE WELD (L.H.) ONLY
7 20BH5012 4 PIN-SPIRAL 5/16 X 1 1/2 *
8 15B1600 4 WASHER 1 SAE P *
9 65106A4 4 WLDMT,AXLE PIVOT PIN *
10 D121 1 DECAL ADJ-NUTS
11 D301 1 DECAL,RHINO
12 00756466 1 LEFT AXLE ARM ASSY
13 00756468 1 RIGHT AXLE ARM ASSY
15 00756465 1 LEFT AXLE ARM WELD N/S
16 00756467 1 RIGHT AXLE ARM WELD
Note: This axle center & win uses hub #00757241 assembly.
FOR REPLACEMENT PARTS ONLY.
*QTY SHOWN FOR 1 MACHINE, COMPLETE
**USED W/FACTORY HYDRAULIC LEVEL LIFT ONLY ITEM #12 THRU #16
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 6
BLADE BAR ASSEMBLY - CTR HEAVY DUTY S/N 01162 - 10429 DEC 1980 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
1 0656160100 1 WLDMT, BLADE CARRIER
2 0652010030 2 BLADE, CCW/CW FLAT
3 571044 2 BOLT SHOULDER
4 571045 2 WASHER
5 5GL16140 2 LOCKNUT 1 -14 LH TLN PL
6 0622010330 2 BLADE, CCW FAN
7 0656150200 2 WASHER,SQ HOLE HT
Note: This carrier was optional until Dec. 1980 then, it became standard. These blade bolts have square shoulders.
The blade bolt hole is 1-25/64 diameter. Check Before Ordering Parts
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 7
BLADE BAR ASSEMBLY - CTR STANDARD S/N 00101 - 01162 OCT 1977 - DEC 1980
ITEM PART NO. QTY. DESCRIPTION
1 701021R 1 CARRIER,BAR BLADE
2 701022R 2 BLADE
3 36107A2ALH 2 BOLT SHOULDER L.H THREAD
4 481043 2 SPCR 1-1/4 X 3/4 X 5/16
5 5GL12160 2 LOCKNUT TLM 3/4 NF PLB L.H. THREAD
6 71103 2 BLD,OFT/FAN,CCW
Note: This blade carrier was standard till Dec. 1980. These Blade bolts have round shoulder.
The blade bolt hole is 1-1/64 dia. Check Before Ordering Parts
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 8
BLADE BAR ASSEMBLY - WING HEAVY DUTY S/N 01162 - 10429 DEC 1980 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
1 0656180100 1 WLDMT, BLADE CARRIER, FS15
2 0652010030 2 BLADE, CCW/CW FLAT
3 0622010330 2 BLADE, CCW FAN
0652010330 3 BLADE, CW FAN
4 571044 2 BOLT SHOULDER
5 571045 2 WASHER
6 5GL16140 2 LOCKNUT 1 -14 LH TLN PL
7 0656150200 2 WASHER,SQ HOLE HT
Note: This was optional till Dec. 1980. These blades bolts have square shoulders.
The blade bolt hole is 1-25/64 dia. Check Before Ordering Parts
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 9
BLADE BAR ASSEMBLY - WING STANDARD S/N 01162 - 10429 OCT 1977 - DEC 1980
ITEM PART NO. QTY. DESCRIPTION
1 711021 1 BLADE CARRIER
2 701022R 2 BLADE
0656240000 2 BLADE STD FAN
3 71103 2 BLD,OFT/FAN,CCW
4 36107A2ALH 2 BOLT SHOULDER
5 5312316 2 WASHER (SPECIAL)
6 5GL12160 2 LOCKNUT TLM (LH) 3/4 NF PLB
Note: This blade carrier was optional till Dec. 1980.
The blade bolt hole is 1-1/64 dia. Check Before Ordering Parts
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 10
BLADE PAN ASSEMBLY - CTR HEAVY DUTY S/N 01162 - 10429 DEC 1980 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
1 0656150100 1 BALDE CARRIER WELDMENT
2 701332 1 DISHPAN
3 0652010030 2 OFFSET FLAT BLADE
0652010030 3 HARD SURFACED OFFSET FLAT BLADE
4 0622010330 2 OFFSET FAN BLADE
5 571044 2 OFFSET HARD SURFACED FAN BLADE
6 7AH5101816 4 BOLT
7 0656150200 2 SPACER WASHER
8 571045 2 SHOULDER BOLT
9 W67 4 HARD WASHER
10 00749136 4 LOCKNUT
11 5GL1640 2 LOCKNUT L.H. THREAD
Note: This carrier was optional until Dec. 1980 then, it became standard. These blade bolts have square shoulders.
The blade bolt hole is 1-25/64 diameter. Check Before Ordering Parts
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 11
BLADE PAN ASSEMBLY - CTR STANDARD S/N 00101 - 01162 OCT 1977 - DEC 1980
ITEM PART NO. QTY. DESCRIPTION
1 701333 1 CARRIER BLADE WELDMENT
2 701332 1 DISHPAN
3 701022R 2 BLADE, OFFSET FLAT
4 71103 2 BLADE, OFFSET FAN
HS71103 2 BLADE OFFSET FAN (HARD SURFACED)
5 36107A2ALH 2 SHOULDER BLADE BOLT
6 7AH5101816 4 BOLT
7 671044 2 SPACER WASHER
8 681064 2 WASHER (HARDENED)
9 W67 4 WASHER (HARDENED)
10 5GR10180 4 NUT-TOPLOCK
11 5GL12160 2 NUT-TOPLOCK LH THREAD
Note: This blade carrier was standard till Dec. 1980. These Blade bolts have round shoulder.
The blade bolt hole is 1-1/64 dia. Check Before Ordering Parts
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 12
BLADE PAN ASSEMBLY - WING HEAVY DUTY S/N 01162 - 10429 DEC 1980 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
1 0656170100 1 BLADE CARRIER, WELDMENT
2 671042 1 BLADE PAN
3 0652010030 2 OFFSET FLAT BLADE, CCW
0652010030 3 OFFSET FLAT BLADE, HARD SURFACED, CCW
0652010030 2 OFFSET FLAT BLADE, CW
0652010030 3 OFFSET FLAT BLADE, HARD SURFACED, CW
4 0622010330 2 OFFSET FAN BLADE, CCW
0622010330 4 OFFSET FAN BLADE, HARD SURFACED, CCW
0652010330 2 OFFSET FAN BLADE, CW
0652010330 2 FAN, BLADE HARD SURFACED, CW
5 571044 2 SHOULDER BOLT (L.H. THREADS)
6 571045 2 SHOULDER BOLT WASHER
7 7AH5101816 4 BOLT
8 W67 4 WASHER
9 00749136 4 LOCKNUT
10 5GL16140 2 LOCKNUT L.H. THREADS
11 0656150200 2 WASHER SPACER
Note: This was optional till Dec. 1980. These blades bolts have square shoulders.
The blade bolt hole is 1-25/64 dia. Check Before Ordering Parts
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 13
BLADE PAN ASSEMBLY - WING STANDARD S/N 00101 - 01162 OCT 1977 - DEC 1980
ITEM PART NO. QTY. DESCRIPTION
1 671041 1 CARRIER, BLADE (WELDMENT)
2 671042 1 BLADE PAN
3 701022R 2 BLADE, OFFSET, CCW
0656240000 2 BLADE, OFFSET, CW (HARD SURFACE)
0656240000 2 BLADE, OFFSET, CW
4 71103 2 BLADE, SUCTION, CCW
0656240000 2 BLADE, SUCTION, CW
71103 2 BLADE, SUCTION, HARD SURFACED, CCW
0656240000 2 BLADE, SUCTION, HARD SURFACED, CW
5 36107A2ALH 2 BOLT, SHOULDER L.H. THD.
6 5312316 2 WASHER, SPECIAL (HEAT TREATED)
7 7AH5101816 4 BOLT
8 W67 4 WASHER, HARD
9 00749136 4 NUT, LOCK HEX.
10 5GI12160 2 NUT, LOCK HEX.
11 671044 2 WASHER, SPACER
Note: This blade carrier was optional till Dec. 1980.
The blade bolt hole is 1-1/64 dia. Check Before Ordering Parts
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 14
CHAIN GUARD - CENTER & WING SECTION S/N 01497 - 10429 JUN 1982 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
0652100000 - CHAIN GUARDS, FRONT
1 0652100100 1 CTR SECT FRNT CHN GD ASSY
2 0652100200 1 FRNT CHN GD ASSY, WING *
3 0652100110 1 WLDMT, MOUNTING BRACKET
4 0652100201 1 GUARD MNTING BRKT *
5 0652100101 69 CHAIN 5/16 5-LINKS
0652100203 63 CHAIN 5/16, 6 LINK *
6 0652100202 1 ROD CHAIN *
7 0652100104 2 ROD CHAIN
8 0652100102 1 ROD CHAIN
9 0652100105 2 ROD CHAIN
10 7A81312 7 C/S1/2 X 1 1/2 NC
5 (WING) *
11 00013300 2 HEXB 1/2 NC 2 PL5 *
12 15B800 7 WASHER 1/2 SAE ZP
7 (WING) *
13 5GR8130 7 NUT,LOCKNUT 1/2 NC
7 (WING) *
Note: These replace assembly used prior to Serial #07497 June 1982. Chain Guards with chain links welded on longer
available.
Leading edge of mower will be turned down 90` approximately.
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 15
CHAIN GUARD - REAR CENTER SECTION S/N 01497 - 10429 JUN 1982 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
0652110000 - CHAIN GUARDS, REAR *
0652110100 1 REAR CHN GD ASSY, CTR SECT
1 0652110101 1 MOUNTING BRACKET
2 0652100203 57 CHAIN 5/16, 6 LINK
3 0652110102 1 ROD,CHAIN GUARD 52 1/2 LG
4 00748823 4 HHCS 1/2-13UNC 1-1/2 PL5
00752680 2 HHCS 1/2-13UNC X 4LG PL5
5 15B800 6 WASHER 1/2 SAE ZP
6 00001800 6 LOCKNUT TLM 1/2 NC PLB
7 0652110103 2 ROD,CHAIN GUARD 11 1/2 LG
?8 652053 2 SPACER
Note: These chain guards as an assembly replace earlier chain guards prior to serial #01497 June 1982. Chain guards
with chain links welded on bracket are no longer available.
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 16
CHAIN GUARD - REAR WING SECTION S/N 01497 - 10429 JUN 1982 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
1 0652110300 1 LEFT REAR WING CHN GD
0652110200 1 RT REAR CHN GD ASSY
2 0652110210 1 MOUNTING BRKT, RIGHT
0652110310 2 MOUNTING BRKT, LEFT
3 00751126 110 CHAIN 5/16 WLD 6 LINK
4 0652110201 2 ROD CHAIN
5 00013300 2 HEXB 1/2 NC 2 PL5
9 652053 8 SPACER
10 00752680 6 HHCS 1/2-13UNC X 4LG PL5
12 7A81336 2 C/S1/2 X 4-1/2 NC PL5
Complete Rear Chain Guard Assembly to include center, left and right wing. See Center Chain Guard Section. These are
the same for all previous serial #’s listed without modification. Chain Guards with welded on links are no longer available.
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 17
CYLINDER ASSEMBLY - CENTER AXLE S/N 00101 - 01377 OCT 1977 - JAN 1982
ITEM PART NO. QTY. DESCRIPTION
1 65113B1 1 CYLINDER
00759946 1 CYLINDER 3 X 8 W/1-1/4 ROD
00755234 1 CONTROL SPACER KIT
2 651302 1 HOSE #6 - 8 MP - 8 MP 180 LG
3 94514 1 ADAPTER, HYD, ELBOW SWIVEL
4 691354 1 CLEVIS 1 1/4-12 NF THD
65113A3 1 CLEVIS 1/16-12 NF THD
7 65113B6 1 COLLAR
651136 1 COLLAR
9 65113B8 1 HEAD 1 1/4 ROD 3 BR
65113A8 1 HEAD 1 1/16 ROD 3 BR
10 65113A9 1 ROD 1 1/4
651139 1 ROD, 1-1/16 DIA.,3/4NF THDS.
11 6511310 1 TUBE CENTER CYL
12 691315 1 PISTON, 3, O RING SEAL
6511311 1 PISTON, 3, UCUP SEAL
13 65113A12 1 CLEVIS BASE 1/2
0651130001 1 CLEVIS BASE 7/16
14 8354 2 PIN-HYD. CYLINDER
15 37107B13 2 CLIP-X HAIR PIN
16 65113A16 4 TIE ROD 1/2 - 13
0651130017 4 TIE ROD
17 6511320 1 NUT, PISTON (3/4-NF HEX)
18 00001200 1 NUT,HEX 1/2 NC PL
00999316 4 NUT HEX 7/16 NC PL
19 6511322 1 BOLT
20 00013901 1 NUT HEX 3/8 NC PL
21 6511324 1 BREATHER,1/2 SQ HD CORED
22 00749508 1 PLUG 1/2-14 NPT
2717100 - SEAL KIT 1 1/4
6511325A - SEAL KIT,3 CROSS CYLINDER 1 1/16
Note: This cylinder was used approx. through 1982. Always check length of barrel, type of stroke control, size and rod
(Item #10), size of tie rods. (Item #16) before ordering parts. Replacement part # for complete assembly is 00759946 and
the stroke control spacer kit is 00755234. This cylind
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 18
CYLINDER ASSEMBLY - CENTER AXLE S/N 00101 - 10429 OCT 1977 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
00759946 CYLINDER 3 X 8 W/1-1/4 ROD
1 8354 2 PIN-HYD. CYLINDER
2 163016 2 PIN, COTTER 3/16 X 2
3 00760199 1 SEAL KIT (3 DIA HYD CYL)
4 4675M 1 NUT PISTON
5 7339 1 BREATHER, CYLINDER
6 00023100 1 HHCS 3/8 -16UNC 1-1/2 PL5
7 00760661 1 PISTON FOR 3BORE CYL
8 00760194 1 TUBE, CYL 3X8
9 00760200 1 PISTON ROD
10 4376 1 NUT HEX 1/2-20 NF PL
11 4690W 8 INSTALL SHEET-BELT TENSIONER&S
12 00760197 1 HEAD, CYL 3
13 8754 1 CLEVIS,OUTER
14 00760196 1 BASE, CYL 3
15 00760202 4 ROD,CYL TIE (1/2NFX13)3X8 CYL
19 00755234 1 CONTROL SPACER KIT
00760199 SEAL KIT (3 DIA HYD CYL)
REPLACEMENT PARTS ONLY
Replacement cylinder not used in production. Used as replacement assembly. Parts WILL NOT interchange with earlier
cylinder.
Note: No screw on stroke control - use clip on spacers. (Item # 19)
Seal Kit # 00760199 contains both old and new style piston seals. New style seal can be installed in old style piston.
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 19
CYLINDER ASSEMBLY - CENTER AXLE S/N 01376 - 10429 JAN 1982 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
1 65113B1 1 CYLINDER
2 651302 1 HOSE #6 - 8 MP - 8 MP 180 LG
3 94514 1 ADAPTER, HYD, ELBOW SWIVEL
4 0651130001 1 CLEVIS BASE
5 0651130005 1 PISTON
6 0651130006 1 ROD
7 0651130007 1 BARREL
8 00750208 1 PLUG,BREATHER 1/2 NPTM - 007
9 0651130012 1 STROKE CONTROL
10 5B6240 1 NUT,ROD CLEVIS
11 7E62414 1 SHCS 3/8 NF 1-3/4
12 02816800 8 NUT 1/2 NF HEX
13 0651130016 1 HEAD 3 HYD CYL 1-1/4 ROD
14 0651130017 4 TIE ROD
15 691351 1 NUT
16 8354 2 PIN-HYD. CYLINDER
17 00000400 4 PIN-COTTER 1/8 X 1-1/2 PLATED
18 0651130022 1 CLEVIS 1-14 NF THD
0651130014 - SEAL KIT,3 LANTEX CYLINDER
Note: This cylinder was used approx. after 1982. Always check length of barrel, and type of stroke control before ordering
part. Replacement part # for complete cylinder assy is 00759946, and stroke control spacer kit is 00755234. Parts Will
Not Interchange.
This is an lantex cylinder length of barrel (Item #7) is 10 1/8" long. Stroke control (Item #9) is round with notches cast into
it.
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 20
CYLINDER ASSEMBLY - LEVEL LIFT - 2-1/2 X 8 SLAVE CYL S/N 00101 - 10429 OCT 1977 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
0652141500 - CLY, LEVEL LIFT
1 0652141501 1 PISTON ROD
2 0652141312 1 PLUG, STRAIGHT ADAPTER
3 0652141502 1 TUBE
4 0652141503 1 HEAD
5 0652141504 1 PISTON
6 5JRC10180 1 NUT TOPLOCK 5/8 NF PLC
7 0652140305 4 TIEROD,HYD CYL W/NUT
8 0652141506 1 CLEVIS,BASE
9 0652140307 1 CLEVIS, ROD
10 691356 2 PIN
11 37107B13 4 CLIP-X HAIR PIN
12 0652141311 2 ADP HYD STGHT 8MB - 8FP
13 691302 1 HYD HOSE-3/8-8W/ 1/2 FITTING (NOT SHOWN)
14 B651302 1 HOSE #6 - 8MP - 8MP - 180LG (NOT SHOWN)
15 6513015 1 HOSE #6 - 8 MP - 8 MP 216 LG (NOT SHOWN)
16 B65113A2 1 HYD HOSE ONE (NOT SHOWN)
17 94514 6 ADAPTER, HYD, ELBOW SWIVEL (NOT SHOWN)
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 21
CYLINDER ASSEMBLY - LEVEL LIFT - 2-3/4 X 8 SLAVE CYL S/N 00101 - 10429 OCT 1977 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
0652141400 - HYD CYL KIT
1 0652141401 1 ROD,PISTON
2 0652141312 1 PLUG, STRAIGHT ADAPTER
3 0652141402 1 TUBE HYD CYL
4 0652141403 1 GLAND,ROD END
5 0652141404 1 PISTON
6 5JRC12100 1 NUT TOPLOCK 3/4
7 0652140305 4 TIEROD,HYD CYL W/NUT
8 0652141406 1 CLEVIS,BASE
9 0652140307 1 CLEVIS, ROD
10 691356 2 PIN
11 37107B13 4 CLIP-X HAIR PIN
12 0652141311 2 ADP HYD STGHT 8MB - 8FP
13 691302 1 HYD HOSE-3/8-8W/(1/2FITTING (NOT SHOWN)
14 B651302 1 HOSE #6 - 8MP - 8MP - 180LG (NOT SHOWN)
15 6513015 1 HOSE #6 - 8 MP - 8 MP 216 LG (NOT SHOWN)
16 B65113A2 1 HYD HOSE ONE (NOT SHOWN)
17 94514 6 ADAPTER, HYD, ELBOW SWIVEL (NOT SHOWN)
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 22
CYLINDER ASSEMBLY - LEVEL LIFT - 3 X 8 SLAVE CYL S/N 00101 - 10429 OCT 1977 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
0652141300 - HYD CYL KIT
1 0652141301 1 PISTON ROD
2 0652141312 1 PLUG, STRAIGHT ADAPTER
3 0652141302 1 TUBE
4 0652141303 1 HEAD
5 0652141304 1 PISTON
6 6511320 1 NUT, PISTON (3/4-NF HEX)
7 0652140305 4 TIEROD,HYD CYL W/NUT
8 0652141306 1 BASE CLEVIS
9 0652140307 1 CLEVIS, ROD
10 691356 2 PIN
11 37107B13 4 CLIP-X HAIR PIN
12 691302 1 HYD HOSE-3/8-8W/ 1/2FITTING (NOT SHOWN)
13 B651302 1 HOSE #6 - 8MP - 8MP - 180LG (NOT SHOWN)
14 6513015 1 HOSE #6 - 8 MP - 8 MP 216 LG (NOT SHOWN)
15 B65113A2 1 HYD HOSE ONE (NOT SHOWN)
16 94514 6 ADAPTER, HYD, ELBOW SWIVEL (NOT SHOWN)
Note; Center Cylinder has stroke control (Item 13) on shaft. The unit must already have hydraulic cylinders to fit arms and
deck.
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 23
CYLINDER ASSEMBLY - LEVEL LIFT REPLACEMENT ASSY (P/N 8719) S/N 00101 - 10429 OCT 1977 - MA
ITEM PART NO. QTY. DESCRIPTION
8719 1 HYDRAULIC CYLINDER
1 8772 1 CAP
2 4705M 1 PISTON NUT
3 8768 1 PISTON
4 8769 1 TUBE
5 4706 1 PISTON ROD
6 8754 1 CLEVIS,OUTER
7 8773 4 TIE ROD
8 4689 8 NUT HEX 9/16-18NF PL
9 8774 1 HEAD
10 8764 1 SEAL KIT
11 8354 2 PIN-HYD. CYLINDER
12 163016 4 PIN, COTTER 3/16 X 2
?13 00755234 1 CONTROL SPACER KIT (NOT SHOWN.)
Note: Center cylinder WILL NOT have screw on stroke control. The unit must already have hydraulic level left for these
cylinders it mount to axle arms and deck.
REPLACE CYL’S ONLY NOT USED IN PRODUCTION UNIT, PARTS WILL NOT INTERCHANE WITH EARLIER
CYLINDERS.
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 24
CYLINDER ASSEMBLY - LEVEL LIFT REPLACEMENT ASSY (P/N 8720) S/N 00101 - 10429 OCT 1977 - MA
ITEM PART NO. QTY. DESCRIPTION
8720 - WING AXLE 3 1/4 X 8 SLAVE CYLINDER
1 8778 1 BASE CLEVIS
2 4705 1 PISTON NUT
3 8775 1 PISTON
4 8776 1 TUBE
5 4706 1 PISTON ROD
6 8754 1 ROD CLEVIS
7 8773 4 TIE ROD
8 4689 8 NUT 9/16 - 18
9 8779 1 HEAD
10 8765 1 SEAL KIT
11 8354 2 PIN, CLEVIS
12 163016 4 COTTER PIN
Note: Center cylinder WILL NOT have screw on stroke control. The unit must already have hydraulic level left for these
cylinders it mount to axle arms and deck.
REPLACE CYL’S ONLY NOT USED IN PRODUCTION UNIT, PARTS WILL NOT INTERCHANE WITH EARLIER
CYLINDERS.
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 25
CYLINDER ASSEMBLY - LEVEL LIFT REPLACEMENT ASSY (P/N 8721) S/N 00101 - 10429 OCT 1977 - MA
ITEM PART NO. QTY. DESCRIPTION
8721 1 CYL HYD LEVEL LIFT 3 DIA
1 8784 1 CAP (HYD. CYLINDER)
2 4675M 1 NUT PISTON
3 8780 1 PISTON
4 8781 1 TUBE
5 8753 1 PISTON ROD
6 8754 1 CLEVIS,OUTER
7 8785 4 TIE ROD
8 4376 8 NUT HEX 1/2-20 NF PL
9 8786 1 HEAD
10 8766 1 SEAL KIT
11 8354 2 PIN-HYD. CYLINDER
12 163016 4 PIN, COTTER 3/16 X 2
Note: Center cylinder WILL NOT have screw on stroke control. The unit must already have hydraulic level left for these
cylinders it mount to axle arms and deck.
REPLACE CYL’S ONLY NOT USED IN PRODUCTION UNIT, PARTS WILL NOT INTERCHANE WITH EARLIER
CYLINDERS.
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 26
CYLINDER ASSEMBLY - WING-HYDRAULIC CYLINDER & HOSE GROUP S/N 00101 - 01376 OCT 1977 - JAN
ITEM PART NO. QTY. DESCRIPTION
1 00759947 1 CYLINDER 3 X 14 W/1-1/4 ROD
2 6513015 1 HOSE #6 - 8 MP - 8 MP 216 LG
3 94514 1 ADAPTER, HYD, ELBOW SWIVEL
4 691351 2 NUT
65130A12 1 CLEVIS 1 1/8-12 NF THD
5 65113B8 1 HEAD 1 1/4 ROD 3 BR
65130A4 1 HEAD 3 BORE X 1-1/8 ROD
65130A4 1 HEAD 3 BORE X 1-1/8 ROD
6 65130B15 1 ROD,CYL 1-1/4 DIA,1-1/4-12 THD
651306 1 ROD
7 651307 1 TUBE OUTBOARD
8 691315 1 PISTON, 3, O RING SEAL
6511311 1 PISTON, 3, UCUP SEAL
9 65113A12 1 CLEVIS BASE 1/2
0651130001 1 CLEVIS BASE 7/16
10 8354 2 PIN-HYD. CYLINDER
11 00000400 4 PIN-COTTER 1/8 X 1-1/2 PLATED
12 65130A8 4 TIE ROD 1/2 X 19
0651300003 4 ROD
13 6511320 1 NUT, PISTON (3/4-NF HEX)
14 00001200 8 NUT,HEX 1/2 NC PL
5B7140 8 NUT 7/16 NC HEX
15 6511322 1 BOLT
16 00013901 1 NUT HEX 3/8 NC PL
17 00750208 1 PLUG,BREATHER 1/2 NPTM - 007
18 00749508 1 PLUG 1/2-14 NPT
65113A30 - SEAL KIT 3 CR CYL, 1 1/4
6513011A - SEAL KIT,3 CROSS CYLINDER 1 1/8
Note: This cylinder used throught approx 1982. Check length of barrel before ordering replacement pars. If the cylinder
was used check size of tie rods (Item #12) and size of cylinder rod (Item #6).
REPLACEMENT PARTS FOR THIS COMPLETE CYLINDER ASSY IS 00759947.
PARTS WILL NOT INTERCHANGE.
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 27
CYLINDER ASSEMBLY - WING-LANTEX HYDRAULIC CYL & HOSE GRP S/N 01377 - 10429 JAN 1982 - MAY
ITEM PART NO. QTY. DESCRIPTION
1 65130B1 1 HYD. CYL. 3" BORE X 14" STROKE 1-1/4" DIA. ROD BASE END
2 6513015 1 HOSE #6 - 8 MP - 8 MP 216 LG
3 94514 1 ADAPTER, HYD, ELBOW SWIVEL
4 0651130001 1 CLEVIS BASE
5 0651130005 1 PISTON
6 0651300001 1 ROD
7 0651300002 1 TUBE
8 5B6240 1 NUT,ROD CLEVIS
9 7E62414 1 SHCS 3/8 NF 1-3/4
10 0651130022 1 CLEVIS 1-14 NF THD
11 02816800 8 NUT 1/2 NF HEX
12 0651130016 1 HEAD 3 HYD CYL 1-1/4 ROD
13 0651300003 4 ROD
14 691351 1 NUT
15 8354 2 PIN-HYD. CYLINDER
16 00000400 4 PIN-COTTER 1/8 X 1-1/2 PLATED
17 00750208 1 PLUG,BREATHER 1/2 NPTM - 007
0651130014 - SEAL KIT,3 LANTEX CYLINDER
Note: This cylinder used approx. After 1982 always check barrel lenght (Item #7) before ordering replacement parts.
REPLACE THIS CYLINDER ASSY WITH #00759947.
PARTS WILL NOT INTERCHANGE.
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 28
CYLINDER ASSEMBLY - WING-REPLACEMENT S/N 00101 - 10429 OCT 1977 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
1 00759947 1 CYLINDER 3 X 14 W/1-1/4 ROD
2 00756496 1 HOSE-#4-6MP-6MP-216LG
3 94517 1 ADAPTER, HYD, ELBOW SWIVEL
4 7329 1 ADAPTER, HYD, STGHT RESTRICTOR
5 94507 1 ADAPTER, HYD, REDUCER
5 00760196 1 BASE, CYL 3
6 00760198 1 PISTON
7 00760201 1 ROD, CYL 3X14
8 00760195 1 TUBE, CYL 3X14
9 00013901 1 NUT HEX 3/8 NC PL
10 00023100 1 HHCS 3/8 -16UNC 1-1/2 PL5
11 8754 1 CLEVIS,OUTER
12 4690W 8 INSTALL SHEET-BELT TENSIONER&S
13 00760197 1 HEAD, CYL 3
14 00760203 4 TIE ROD, CYL 3X14
15 4675M 1 NUT PISTON
16 8354 2 PIN-HYD. CYLINDER
17 162012 2 PIN,COTTER
18 6511324 1 BREATHER,1/2 SQ HD CORED
?19 00760199 SEAL KIT (3 DIA HYD CYL)
Note: This is a replcaement cylinder and was not used in production.
PARTS WILL NOT INTERCHANGE WITH EARLIER CYLINDERS.
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 29
DECALS S/N 00101 - 10429 OCT 1977 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
1 D303 3 DECAL,RHINO
2 D301 1 DECAL,RHINO
3 D337 3 DECAL-FLX-S-15
5 D121 1 DECAL ADJ-NUTS
6 D122 1 DECAL(PREV. STREAKNG)
7 999200 1 DECAL GENERAL WARNING ALL UNIT
8 D112 1 DECAL USE SAE GER LUB
9 D103 1 DECAL,OPERATE AT 540 RPM
10 D102 1 DECAL PTO SFT TO HTCH
11 D101A 4 DECAL OIL LEVEL
12 D137 1 DECAL CCW BLADE ROTATION
13 99203 2 DECAL, RED REFLECTOR
14 D138 1 DECAL-CW BLADE ROTATION
15 D131 1 DECAL NOTICE
16 D304 2 DECAL (RHINO)
17 NFS 1 SERIAL NUMBER PLATE
18 999403 1 DECAL-DANGER, OFFSET WGT. BOX
21 00756494 3 DECAL-DANGER,DRIVELINE
23 99204 1 DECAL-YELLOW REFLECTOR
24 999401 2 DECAL, ROTATING BLADE
26E127001 A/R PAINT,1 QT,RH ORANGE
26E127004 A/R PAINT, 1 GAL,RH ORNG
26E127000 A/R PAINT,(SPRAY)RHINO ORANGE
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 30
DEFLECTOR - REAR WING S/N 01497 - 10429 JUN 1982 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
6 00002700 10 FLATWASHER 1/2 PL STD
7 00001800 10 LOCKNUT TLM 1/2 NC PLB
8 00756876 2 WING REAR COVER
13 02030700 7 HHCS 1/2-13UNC 1-1/4 PL5
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 31
DEFLECTOR - RUBBER FRONT CENTER S/N 00101 - 10429 OCT 1977 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
00758370 1 DEFLECTOR, ASY, FRT CTR
1 00758261 1 BAND RUBBER GD FRT CTR
2 00758263 1 PANEL RUBBER GD FRT CTR
3 02030700 3 HHCS 1/2-13UNC 1-1/4 PL5
4 00001800 3 LOCKNUT TLM 1/2 NC PLB
Note: These will not fit earlier serial numbers. Complete of deflectors front-center, left and right wings assembly
#00758355.
For 10 foot unit order assembly #00756994.
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 32
DEFLECTOR - RUBBER FRONT WING LEFT & RIGHT S/N 00101 - 10429 OCT 1977 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
00758368 1 DEFLECTOR ASSEMBLY
1 00758264 1 PANEL
2 00758259 1 BAND
3 02030700 7 HEX BOLT
4 00001800 7 LOCKNUT
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 33
DEFLECTOR - RUBBER LEFT & RIGHT CENTER S/N 00101 - 10429 OCT 1977 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
00758369 1 DEFLECTOR, ASY, FRT L-R CTR
1 00758262 1 PANEL RUBBER GD L&R CTR
2 00758260 1 BAND, RUBBER GD LH & RH
3 02030700 2 HHCS 1/2-13UNC 1-1/4 PL5
4 00001800 2 LOCKNUT TLM 1/2 NC PLB
Note: These will not fit earlier serial numbers. Complete of deflectors front-center, left and right wings assembly
#00758355.
For 10 foot unit order assembly #00756994.
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 34
DRIVELINE ASSEMBLY - CTR GEARBOX SQUARE SHAFT SLIP 35R S/N 00101 - 10429 OCT 1977 - MAY 19
ITEM PART NO. QTY. DESCRIPTION
1 0657070000 1 DRIVELINE, SLIP ASSY
W707LSA 1 CTR D/L,S15,
2 W341 1 SHAFT SQ
3 W324 1 YOKE 1 3/16 SQ HOLE PAINT BLK
4 9C482010 1 SHSS 1/2 NF 1-1/4
5 5B8200 1 NUT 1/2 NF HEX
6 W318 1 YOKE W/TAPERED SHAFT PAINT BLK
W284A 1 YOKE,SLIDE COLLAR PAINT BLACK
7 W3071 1 YOKE, TORQUE LIMITER (7-1/16
8 271105B 1 BUSHING SP & TL YOKE
9 7AH551816 4 HEXB 5/16NC 2
10 5JRC5180 4 NUT TOPLOCK 5/16
11 W279R 2 CROSS REPAIR KIT, CTR
12 W324A 1 YOKE,1-3/16 SQ HOLE W/SETSCREW
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 35
DRIVELINE ASSEMBLY - OUTBOARD SQUARE SHAFT ASSEMBLY 35R S/N 00101 - 10429 OCT 1977 - MAY 1
ITEM PART NO. QTY. DESCRIPTION
1 W705RB7 1 SHFT, SHLD,SM TL YK
2 W316B 1 YK & SHFT ASSY 39-1/8
3 W3071 1 YOKE, TORQUE LIMITER (7-1/16
4 271105B 1 BUSHING SP & TL YOKE
5 W279R 1 CROSS REPAIR KIT, CTR
6 7AH551816 4 HEXB 5/16NC 2
7 5JRC5180 4 NUT TOPLOCK 5/16
8 W702RZ4 1 HSG, SHLD,TPR YOKE
W702RZ 1 HSG, SHLD,QD YOKE
9 W312Z 1 YOKE TB & SLV 50
10 W318 1 YOKE W/TAPERED SHAFT PAINT BLK
W284A 1 YOKE,SLIDE COLLAR PAINT BLACK
11 17C1981 1 GREASE ZERK
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 36
DRIVELINE ASSEMBLY - PTO SQUARE SHAFT ASSEMBLY 44R S/N 00101 - 10429 OCT 1977 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
1 W805O4 1 SHFT, SHLD,TPR YK PAINT BLACK
W805O11 1 SHAFT 44R SQ ASY 1-3/4-20 SPL
2 W816A 1 YOKE SHAFT PAINT BLACK
3 W826 1 YOKE,SAE TAPER PAINT BLACK
W827A 1 YOKE,CLP,1-3/4-20SP PAINT BLK
4 W840 1 CROSS REPR KIT
5 W802B 1 HSG,SHLD,QD YK PAINT BLACK
6 W812A 1 YOKE SLEEVE PAINT BLACK
7 W821A 1 YOKE,Q.D. 6BSPLN PAINT BLACK
8 W44B2A 1 QD REPAIR KIT
9 W44B3 1 SPRING-PIN LOCK
10 W44B4A 1 WASHER X
11 17C1981 1 GREASE ZERK
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 37
DRIVELINE ASSEMBLY - SHIELDING ASSEMBLY SQUARE SHAFTS S/N 00101 - 10429 OCT 1977 - MAY 198
ITEM PART NO. QTY. DESCRIPTION
1 W811Q AR SHIELD D/L OUTER PAINT BLACK
W815R AR SHLD IN ASSY PAINT BLACK
2 W315RA1 AR SHIELD ASSY, INNER
4 W311RZ1 AR SHIELD, OUTER
5 W335 AR BEARING, NYLON
00751176 AR RETAINER, NYLON BRG.
6 W936 AR WASHER THRUST
7 W937 AR RING SNAP
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 38
NOTES
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 39
GEARBOX ASSEMBLY - CENTER SECTION S/N 00101 - 10429 OCT 1977 - MAY 1988
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 40
GEARBOX ASSEMBLY - CENTER SECTION S/N 00101 - 10429 OCT 1977 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
1 7010414 1 HOUSING MAIN
2 00748532 1 HOUSING-BEARING CAP
3 00752155 1 CAP BEARING RETAINING
4 7010416 1 SHAFT, INPUT 1-3/8-6
5 701047R 1 OUTPUT SHAFT & GEAR
6 00752159 1 GEAR BEVEL-22 TOOTH
7 00748527 1 BEARING CONE TIMKEN #LM603049
8 00748525 1 BEARING CUP
9 00753738 1 BEARING CONE 16137
10 00753737 1 BEARING CUP 16282
11 00748522 2 BEARING CONE
12 701044R 2 BEARING CUP 363
13 00749509 1 SEAL
14 00748519 1 OIL SEAL
15 7010422 1 RING
16 00748526 2 RING, RETAINING
17 701046R 1 SPACER
18 00758647 A/R SHIM, ADJUSTMENT .010 OR .25M
19 7010419 A/R SHIM KIT
20 00758648 1 SHIM ,ADJUSTMENT O.5
21 00011400 8 HHCS 3/8 NC 1 PL5
22 02030700 4 HHCS 1/2-13UNC 1-1/4 PL5
23 7AH5121620 4 C/S 3/4 X 2 1/2 NF 5
24 00011700 8 LOCKWASHER 5/16 PL STD
25 00753743 4 LOCKWASHER
26 00748547 1 FLATWASHER 1-1/32 X 2-3/16X.22
27 00748539 4 NUT TOPLOCK 3/4 NF PLB
28 5E16140 1 NUT CASTLE 1 -14 STD PL
29 00606000 1 PIN-COTTER 3/16 X 2
30 00565000 1 PLUG, HEX HEAD PIPE 1/8-27NPT
31 00749508 2 PLUG 1/2-14 NPT
32 5312316 4 WASHER (SPECIAL)
NOTE: ITEM 15,23,27, & 32 NOT INCLUDED WITH GEARBOX ASSEMBLY AND MUST BE SPECIFIED WHEN
ORDERING 701041 GEARBOX ASSEMBLY.
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 41
GEARBOX ASSEMBLY - DIVIDER (COMER) S/N 01901 - 10429 FEB 1985 - MAY 1988
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 42
GEARBOX ASSEMBLY - DIVIDER (COMER) S/N 01901 - 10429 FEB 1985 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
0656030000 DIVIDER GEARBOX
1 00753232 1 CASING
2 00753240 1 COVER
3 00753233 1 SHAFT
4 00753221 2 SHAFT
5 00753234 1 CROWNWHEEL
6 00753228 2 BEVEL PINION
7 00753223 4 BEARING
8 00755070 2 BEARING
9 00753238 2 OIL SEAL
10 00753225 2 OIL SEAL
11 00753237 2 INTERNAL CIRCLIP
12 00753237 2 INTERNAL CIRCLIP
13 00753239 1 OIL FILLER PLUG
14 00753226 2 PLUG
15 00753230 6 HEXB METRIC 8-P1.25- 30MM PL5
16 00753231 6 SCHNORR WASHER
17 00755069 1 GASKET
19 00753222 2 SHIM
21 00753235 2 SHIM
22 00753227 2 TAKE-UP RING
NOTE: ITEMS 30 AND 31 ARE NOT FURNISHED WITH THE GEARBOX ASSEMBLY. THIS GEARBOX HAS 1 3/8
TAPER SHAFTS.
P/N 651033 GEAR REPLACE BY P/N 00757028.
Offest units used gearbox#0651030000 (same as #65103 except only on wing out put shaft) Cover #0682053, 6 bolts
#0682053, 6 bolts #7A10118, &6 lockwashers #131000.
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 43
GEARBOX ASSEMBLY - DIVIDER S/N 00101 - 01900 OCT 1977 - FEB 1985
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 44
GEARBOX ASSEMBLY - DIVIDER S/N 00101 - 01900 OCT 1977 - FEB 1985
ITEM PART NO. QTY. DESCRIPTION
65103 GEARBOX ASSY
1 16212012 4 COTTER PIN
2 5312315 3 CASTE NUT (SPECIAL THIN)
3 5312316 4 SPECIAL WASHER (HEAT TREATED)
4 651035 1 INPUT SHAFT
5 651037 1 BEARING CARRIER CAP
6 7A1101110 18 PLACE BOLT
7 00757028 3 BEVEL GEAR, 18-TEETH
8 651031 1 PRIMARY GEAR BOX HOUSING
9 5312312 3 SHIM SET
10 PT204A 3 GASKET
11 531232 2 DRIVE SHAFT HOUSING
12 651036 2 OUTPUT SHAFT
13 W84 3 BEARING CUP
14 W83 3 BEARING CONE
15 PT103 2 OIL SEAL
16 271096 2 BEARING COLLAR
17 5312310 4 KEY (HEAT TREATED)
18 PT104 2 LOCKNUT
19 PT105 2 LOCKWASHER
20 531237 3 BEARING CUP
21 531238 3 BEARING CONE
22 PT209 3 WOODRUFF KEY
23 5310415 2 OIL SEAL
24 651034 1 GASKET
25 00001300 8 LOCKWASHER
26 00750959 8 CAPSCREW
27 301021 1 BREATHER PLUG
28 651032 1 GEAR BOX COVER PLATE
29 00751003 1 PIPE PLUG
30 00010300 6 LOCKWASHER
31 00752658 6 CAPSCREW
32 5DR12160 1 NUT
33 D112 1 DECAL (USE SAE GEAR LUBE)
34 D101A 1 DECAL (OIL LEVEL)
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 45
GEARBOX ASSEMBLY - LEFT WING S/N 00101 - 10429 OCT 1977 - MAY 1988
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 46
GEARBOX ASSEMBLY - LEFT WING S/N 00101 - 10429 OCT 1977 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
0656230000 GEARBOX
1 00563900 1 MAIN HOUSING
2 00564300 1 CAP, BEARING
3 711052 1 CAP W/SPACER
4 0656230001 1 SHAFT,1-3/8-6 INPUT W/PILOT
5 00564000 1 PINION OUTPUT SHAFT
6 00564600 1 INPUT GEAR
7 00564800 1 BEARING,BALL
8 00563700 3 BEARING, BALL
9 00757682 1 SPACER, BEARING
10 00564400 A/R SHIM
11 00563600 1 GASKET
12 00612703 2 SNAP-RETAINER RING
13 00564500 1 RING,RETAINING
14 00564100 3 RING, RETAINING
15 00563500 1 SEAL, OIL OUTPUT
16 00564200 1 OIL SEAL
17 00565000 1 PLUG, HEX HEAD PIPE 1/8-27NPT
18 00749508 1 PLUG 1/2-14 NPT
19 00011400 6 HHCS 3/8 NC 1 PL5
20 00753642 4 HHCS,3/8NC X 1-1/4,ZP,GRD5
22 7AH5101816 4 C/S 5/8 X 2 NF GR5
24 W67 4 WASHER
25 00011700 10 LOCKWASHER 5/16 PL STD
26 00748547 1 FLATWASHER 1-1/32 X 2-3/16X.22
28 5E16140 1 NUT CASTLE 1 -14 STD PL
29 00606000 1 PIN-COTTER 3/16 X 2
30 00749136 4 NUT TOPLOCK 5/8 NF PLB
IMPORTANT NOTE: Item #3 and Item #9 must be replaced together at the same time, do not change one without the
other. If #711052 or #6710510 is ordered a cup and spacer will be shipped together as a kit so order one # or the other,
not both.
ITEMS 12,22,24,29, AND 30 ARE NOT FURNISHED WITH GEARBOX ASSEMBLY AND MUST BE SPECIFIED, IF
REQUIRED.
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 47
GEARBOX ASSEMBLY - RIGHT WING S/N 00101 - 10429 OCT 1977 - MAY 1988
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 48
GEARBOX ASSEMBLY - RIGHT WING S/N 00101 - 10429 OCT 1977 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
0656220000 - GEARBOX
1 0656220001 1 HOUSING
2 0656220003 1 CAP
3 00757683 1 CAP, OUTPUT
4 0656220002 1 SHAFT
5 00564000 1 PINION OUTPUT SHAFT
6 00564600 1 INPUT GEAR
7 00564800 1 BEARING,BALL
8 00563700 3 BEARING, BALL
9 00757682 1 SPACER, BEARING
10 00564400 A/R SHIM
11 00563600 1 GASKET
12 00612703 2 SNAP-RETAINER RING
13 00564500 1 RING,RETAINING
14 00564100 3 RING, RETAINING
15 00563500 1 SEAL, OIL OUTPUT
16 00564200 1 OIL SEAL
17 00565000 1 PLUG, HEX HEAD PIPE 1/8-27NPT
18 00749508 1 PLUG 1/2-14 NPT
19 00011400 6 HHCS 3/8 NC 1 PL5
20 00753642 4 HHCS,3/8NC X 1-1/4,ZP,GRD5
22 7AH5101816 4 C/S 5/8 X 2 NF GR5
23 00751003 1 PIPE PLUG 1/4 NPTM STANDARD
24 W67 4 WASHER
25 00011700 10 LOCKWASHER 5/16 PL STD
26 00768547 1 DECAL - PC2040
28 5E16140 1 NUT CASTLE 1 -14 STD PL
29 00606000 1 PIN-COTTER 3/16 X 2
30 00749136 4 NUT TOPLOCK 5/8 NF PLB
IMPORTANT NOTE: Item #3 and Item #9 must be replaced together at the same time, do not change one without the
other. If #711052 or #6710510 is ordered a cup and spacer will be shipped together as a kit so order one # or the other,
not both.
ITEMS 12,22,24,29, AND 30 ARE NOT FURNISHED WITH GEARBOX ASSEMBLY AND MUST BE SPECIFIED, IF
REQUIRED.
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 49
GEARBOX ATTACHMENT - DIVIDER & CENTER GEARBOX S/N 00101 - 10429 OCT 1977 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
1 0651470000 1 SHIELD ASSEMBLY
0656130100 1 SHIELD, PRIMARY GEARBOX
2 0656520000 1 CTR GEAR BOX SHIELD
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 50
GEARBOX ATTACHMENT- RIGHT & LEFT WING GEARBOX S/N 00101 - 10429 OCT 1977 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
1 0656451210 1 SHIELD WLD
0656451110 1 SHIELD WLD
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 51
HOSE BRACKET COMPONENTS S/N 00101 - 10429 OCT 1977 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
1 0651140100 1 WLDMT, HYD. HOSE BRKT
2 0651150100 1 HYD. HOSE BRKT.
3 02675800 2 HHCS 5/8-11UNC 1-1/2 PL5
4 00010400 2 NUT 5/8 NC HEX PL
5 00010300 2 LOCKWASHER 5/8 PL STD
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 52
HUB ASSEMBLY - CENTER & OUTBOARD S/N 10148 - 10428 JAN 1988 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
00757241 WHEEL HUB, PREASSY
3 00756576 1 BEARING CUP OUTSIDE
4 00750434 1 BEARING CONE INSIDE
5 00756577 4 BEARING CUP INSIDE
6 00752177 5 BOLT, STUD 1/2-20 NF X 1-7/8
7 00750614 5 NUT 1/2-20NF 90DEG.CONE LUG PL
8 00756490 1 NUT SLOTTED THIN 1 NF PLC
9 00750616 1 OIL SEAL
10 00756493 1 WASHER
11 00756492 1 DUST CAP
12 00026200 1 PIN-COTTER 5/32 X 1-1/2
13 00003500 1 ZERK FITTING 1/8 STRAIGHT
14 00756489 1 HUB W/ CUPS & STUBS
15 0371242102 1 BEARING CONE
Note: This hub was used on all center and outboard, standard, level lift axles between these serial numbers. this hub has
no washer behind seal on spindle and logo cast into backside of hub.
When using sectional tires install item #7 flat against wheel, opposite picture.
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 53
HUB ASSEMBLY - OUTBOARD AXLES S/N 00101 - 10147 OCT 1977 - JAN 1988
ITEM PART NO. QTY. DESCRIPTION
271033 HUB GROUP ASSY
3 PT108 1 BEARING CUP
4 00006500 1 BEARING CONE
5 00016900 1 BEARING CUP
6 13198 5 BOLT, HUB
7 00750614 5 NUT 1/2-20NF 90DEG.CONE LUG PL
8 5DR12160 1 NUT 3/4 NF SLOTTED
9 00771458 1 OIL SEAL
10 15B1200 1 WASHER 3/4 P SAE
11 PT112 1 HUB CAP
12 1621/2010 1 CTR
13 00003500 1 ZERK FITTING 1/8 STRAIGHT
14 PT110SA 1 WHEEL HUB
15 PT109 1 BEARING CONE
Note: When using sectional tires install item #7 flat against wheel, opposite picture.
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 54
HUB ASSEMBLY - STANDARD CENTER AXLE S/N 00101 - 10147 OCT 1977 - JAN 1988
ITEM PART NO. QTY. DESCRIPTION
371247 HUB, ASY
3 00016900 1 BEARING CUP
4 371247E 1 BEARING CONE 342A
5 371247D 1 BEARING CUP 332
6 13198 5 BOLT, HUB
7 00750614 5 NUT 1/2-20NF 90DEG.CONE LUG PL
8 371247J 1 NUT, 7/8-14 UNF STD SLOTTED
9 371247F 1 SEAL
10 371247H 1 WASHER
11 371247H 1 WASHER
12 1621/2012 1 PINS-CTR 5/32 X 1 1/2
13 00003500 1 ZERK FITTING 1/8 STRAIGHT
14 371247SA 1 HUB
15 371247C 1 BEARING CONE
Note: Spindel will have washer welded to it behind seal. When using sectional tires install item #7 flat against wheel,
opposite picture.
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 55
HYDRAULIC CONTROL VALVE MOUNTING KIT S/N 00101 - 10429 OCT 1977 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
1 651401 1 MT BKT WLD
2 00016200 6 HHCS 5/16NC 2 PL5
3 13500 6 L WSHR 5/16
4 5B5180 6 NUT 5/16 NC HEX
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 56
HYDRAULIC HOSE ADAPTERS S/N 00101 - 10429 OCT 1977 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
2 00275400 3 Q.D, COUPLER #8
4 651311 3 QD COUPLER HALF FEMALE
5 651312 3 COUPLER HALF, MALE
Note: Choice of couplers is up to the customer.
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 57
HYDRAULIC VALVE ASSEMBLY - DETENT W/SPRING ASSEMBLY S/N 00101 - 10429 OCT 1977 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
18 6514016 1 HOUSING DETENT
19 6514017 1 SLEEVE
20 6514018 1 WASHER
21 6514019 1 SPRING CENTERING (25#)
22 6514020 1 COLLAR STEP
23 6514021 1 WASHER
24 7E42012 1 C/S1/4 X 1 1/2 SK HD
25 6514022 1 CAP,END
26 7D42014 4 BOLT
27 6514023 1 BALL 1/4 STEEL
28 6514024 1 SPRING
29 6514025 1 PLUG
30 65140A54 1 WASHER
Standard quantities for one Detent Assembly 3 required per hydraulic valve.
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 58
HYDRAULIC VALVE ASSEMBLY - OPEN/CLOSED CENTER VALVE S/N 00101 - 10429 OCT 1977 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
1 19E13/41/2 2 PIPE BUSHING
2 65140A47 3 HANDLE
3 65140A48 3 KIT-PIN
4 7E4204 6 SHCS 1/4 NC 1/2
5 65140A46 3 BRKT
6 6514012 6 PLATE RETAINER
7 6514013 6 SEAL, O-RING
8 6514026 3 POPPET
9 6514027 3 SPRING,LIFT CHECK
10 6514028 3 SEAL, O-RING
11 6514029 3 PLUG
12 6514030 3 PLATE,1/16 ORIFICE
13 6514031 3 RETAINER
14 65140A50 1 NON -ADJUSTABLE RELIEF ASSEMBLY (OPEN CENTER ONLY)
15 6514042 1 CLOSED CENTER ASSEMBLY (CLOSED CENTER ONLY)
16 6514039 1 CONVERSION PLUG ASSEMBLY
17 6514037 1 NO-RELIEF ASSEMBLY (CLOSED CENTER ONLY)
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 59
JACK ASSEMBLY - TOP WING S/N 00101 - 10429 OCT 1977 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
1 0811140000 1 PARKING JACK
2 00749892 1 PIN-JACK RETAINING
3 00751685 1 PIN-CLIP HAIR
4 651081W 1 BKTS PARKING JACK
5 7A101116 2 BLT 5/8 X 2 ZP
6 131000 2 LOCK WASHER
7 5B10110 2 NUT 5/8 HEX, ZP
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 60
LEFT SCREW S/N 00101 - 10429 OCT 1977 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
1 0656510000 1 MANUAL-LIFT SCREW
2 651062F 2 FITTING,GREASE (DRIVE TYPE)
3 00609200 2 HEXB 1 NC 4 GR5
4 02030300 2 NUT TOPLOCK 1 NC PLB
5 00760135 1 HANDLE,MANUAL LIFT SCREW
6 00756579 1 TOP LINK THREAD LOCK
?7 0656510001 1 MANUAL-LIFT SCREW
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 61
LEVEL LIFT KIT FIELD INSTALLATION S/N 00101 - 10429 OCT 1977 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
1 0652140120 1 WLDMT, BASE
2 0652140130 1 WLDMT, PIVOT ARM
3 0652140140 1 WLDMT, SPRING ROD
4 0652140150 1 SPRING GUIDE
5 371063A 1 SPRING
6 0652140160 1 PIN
7 691154 1 PIN
8 5GR12100 1 LOCKNUT TLM 3/4 NC PL
9 7AH5101132 2 C/S 5/8 X 4 NC GR.5
10 02956948 2 LOCKNUT 5/8 NC PLC
11 15B1600 1 WASHER 1 SAE P
12 163016 1 PIN, COTTER 3/16 X 2
13 65107A3C 1 WASHER
14 0652150100 1 AXLE LUG ASSEMBLY
0652150000 LEVEL LIFT KIT FS15
Note: Factory level lift did not use bracket #14 on axle arms. Axle arms had longer lugs on them.
To order complete field installation level lift kit, including hydraulic cylinders and hoses, order bundle #0652150000. (Most
current type cylinder used will be used shipped)
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 62
LEVEL LIFT ROD ASSEMBLY S/N 10148 - 10428 JAN 1988 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
1 584042 2 WLDMT-ROD CONTROL
2 651101 2 ROD
3 00770485A 2 NUT,EXTENDED ADJUSTMENT
4 651102 4 PIN-DRILLED
5 5C1490 2 HEXNUT 7/8 JAM ZP
6 00606000 8 PIN-COTTER 3/16 X 2
7 15B1200 8 WASHER 3/4 P SAE
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 63
MAINFRAME ASSEMBLY S/N 00101 - 01900 OCT 1977 - FEB 1985
ITEM PART NO. QTY. DESCRIPTION
1 0656011000 1 WLDMT, FS15 CTR SECT M.FF
2 0656020200 1 L/H O/B FRAME WLD
3 0656020100 1 R/H O/B FRAME WLD
4 65109 2 PIN HINGE
5 20A4012E 2 PIN
6 5710121 3 COVER PLATE
7 5F5180 6 NUT 5/16 NC WING
8 0656270000 2 T,SPACER,LONG
9 0656261000 2 SPACER,SHORT HINGE
0656260000 2 SPACER,SHORT
Note: Later models replaced lock pin w/bolts and nut. Part number 7A51812 bolt, 5GR5180 locknut.
PART NUMBER 0656261000 REPLACES PART NUMBER 0656260000 FOR SERIAL # 00631 AND ON. PART
NUMBER 0656261000, 21-5/8" LONG. PART #0656260000, 171/4" LONG.
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 64
MAINFRAME ASSEMBLY S/N 01901 - 10429 FEB 1985 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
1 0656011000 1 WLDMT, FS15 CTR SECT M.FF
2 0656020200 1 L/H O/B FRAME WLD
3 0656020100 1 R/H O/B FRAME WLD
4 65109 2 PIN HINGE
5 20A4012E 2 PIN
6 5710121 3 COVER PLATE
7 5F5180 6 NUT 5/16 NC WING
8 0656270000 2 T,SPACER,LONG
9 0656261000 2 SPACER,SHORT HINGE
0656260000 2 SPACER
Note: Later models replaced lock pin w/bolts and nut. Part number 7A51812 bolt, 5GR5180 locknut.
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 65
SKID SHOE & SIDE SKIRT - OFFSET MODELS CTR SECTION S/N 00101 - 10429 OCT 1977 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
1 652071 1 SIDESKIRT WLDMT, LEFT SIDE
2 65203L 1 SHOES SLIDE
3 2A381312 3 BOLT,PLOW 1/2 NC X 1-1/2 GR.5
4 00001200 8 NUT,HEX 1/2 NC PL
5 00001300 8 LOCKWASHER 1/2 PL STD
6 281316 3 CARB 1/2NC X 2
7 00748823 2 HHCS 1/2-13UNC 1-1/2 PL5
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 66
SKID SHOE & SIDE SKIRT S/N 00101 - 10429 OCT 1977 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
1 65202RW 1 SKIRT SIDE
2 65202LW 1 SKIRT SIDE
3 65203R 1 SHOES SLIDE
4 65203L 1 SHOES SLIDE
5 15B800 12 WASHER 1/2 SAE ZP
6 00001200 18 NUT,HEX 1/2 NC PL
7 7A81312 12 C/S1/2 X 1 1/2 NC
8 13800 18 LOCK WASHER
9 2A381312 6 BOLT,PLOW 1/2 NC X 1-1/2 GR.5
10 D303 2 DECAL,RHINO
11 D337 2 DECAL-FLX-S-15
Note: This side skirt is 1/4" thick. Replace old 3/16" Thick side skirt with out modification.
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 67
SKID SHOE ASSEMBLY S/N 00101 - 00466 OCT 1977 - FEB 1979
ITEM PART NO. QTY. DESCRIPTION
1 0656490010 1 ASY,RIGHT SKID SHOE
0656490020 1 ASY,LEFT SKID SHOE
2 2A381312 2 BOLT,PLOW 1/2 NC X 1-1/2 GR.5
3 00001200 5 NUT,HEX 1/2 NC PL
4 13800 5 LOCK WASHER
5 00013300 3 HEXB 1/2 NC 2 PL5
6 15B800 2 WASHER 1/2 SAE ZP
7 0656490107 1 WEAR PLATE
Note: Later Models have item 1 welded to center section of the mainframe at assembly. These can be used to replace
skid shoe mount broken off on units
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 68
SKID SHOE ASSEMBLY S/N 00101 - 10429 OCT 1977 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
1 0656490107 1 WEAR PLATE
2 2A381312 2 BOLT,PLOW 1/2 NC X 1-1/2 GR.5
3 00001200 2 NUT,HEX 1/2 NC PL
4 13800 2 LOCK WASHER
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 69
SPRING ASSEMBLY - CENTER AXLE S/N 00101 - 10429 OCT 1977 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
1 0656460110 1 UPPER SPRING WLD
2 0656460120 1 LOWER SPRING WLD
3 5JRC12100 4 NUT TOPLOCK 3/4
4 371063A 4 SPRING
5 65107A4 4 GUIDE SPRING
6 00002701 4 FLATWASHER,3/4,TYPE AW,ZP
7 02023800 4 HEXB 3/4 NC 6-1/2PL
8 37107B13 2 CLIP-X HAIR PIN
9 0656460240 2 WLDMT-PIN
Note: Center Spring Assembly was optional eqpt.
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 70
SPRING ASSEMBLY - WING S/N 00101 - 10429 OCT 1977 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
0656460200 OUTBOARD SPRING ASSY
1 0656460220 1 ROCKER ARM WLD
2 0656460210 1 SPRING BASE WLD
3 37107B13 2 CLIP-X HAIR PIN
4 0656460230 1 PIN-WLD
5 65107A4 1 GUIDE SPRING
6 371063A 1 SPRING
7 00037200 1 NUT TOPLOCK 3/4 NC PLC
8 02023800 1 HEXB 3/4 NC 6-1/2PL
9 0656460240 1 WLDMT-PIN
10 00002701 1 FLATWASHER,3/4,TYPE AW,ZP
Note: These sere not used on units with hyd level lift. See level lift section for spring assy’s used
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 71
TIRE/WHEEL ASSEMBLY S/N 00101 - 10429 OCT 1977 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
1 00008700 1 WHEEL, 15 X 5.00 DC (RIM ONLY)
1 00019200 1 WHEEL 14 X 5.00 DC (RIM ONLY)
2 00025200 1 LAMINATED PUNCTURE-PROOF TIRE & WHEEL ASSEMBLY (21" OD) 6.00 X 9
00749700 14" AIRPLANE TIRE AND WHEEL
ALSO AVAILABLE
Used 14" Airplane Tire and Wheel - P/N 00749700 (not shown)
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 72
TONGUE ASSEMBLY S/N 00101 - 10429 OCT 1977 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
1 B65105 1 TONGUE
651051 1 WLDMT, TONGUE
2 0656050200 1 WLDMT, TONGUE HITCH, FS15 PART
651052 1 CLEVIS, TONGUE
3 0656050300 1 TNG-HITCH CONT ROD
651053 1 ROD HITCH CONTROL
4 651054 2 PIN-TONGUE PIVOT
5 7AH5121620 2 C/S 3/4 X 2 1/2 NF 5
6 00752161 1 HHCS 3/4 NF 3 PL5
7AH5121636 6 C/S 3/4 X 4 1/2 NF 5
7 00748539 3 NUT TOPLOCK 3/4 NF PLB
8 00606000 2 PIN-COTTER 3/16 X 2
Note: Item #6 has ears cast on to it. Check before ordering. Item #5 bronze bushing
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 73
TORQUE LIMITER ASSEMBLY S/N 00101 - 10001 OCT 1977 - AUG 1987
ITEM PART NO. QTY. DESCRIPTION
70105 TORQUE LIMITER ASSY
1 701052 1 DRIVE PLATE
2 00748832 1 PLATE,PRESSURE
3 00748833 2 DISC,CLUTCH
4 701054R 1 HUB, TORQUE LIMITER
5 00748825 1 BUSHING
6 701055R 1 NUT ADJ TOPLOCK
7 00748831 4 SPRING, BELLEVILLE
8 701053R 1 PLUG BRONZE
9 9C16163 1 SHSS CUP POINT 3/8NC X 3/8 PL
10 00748834 1 BACK PLATE
Note: Item #7 is hex shaped nut. Check before ordering.
Notice: Most Parts are interchangeable with the Warner-Motive Torque Limiter (70105). To prevent damage to the
assembly, do not use or mix 0731070006 spring together with 701056 spring on the sam assemly. Also, replacement of
the disc and spring with Warner parts will lower the capacity of the
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 74
TORQUE LIMITER ASSEMBLY S/N 10001 - 10429 AUG 1987 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
0731070000 TORQUE-LIMITER 3SPG
1 00748829 1 HUB
2 00748834 1 BACK PLATE
3 0731070003 2 DISK, FRICTION
4 0731070004 1 PLATE,DRIVE
5 0731070005 1 PLATE, PRESSURE
6 0731070006 3 SPRING, BELLVILLE
7 0731070007 1 NUT, ADJUSTING
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 75
WEIGHT BOX S/N 00101 - 10429 OCT 1977 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
1 0656390100 1 WEIGHT BOX WELD
2 0656390300 1 COVER
3 12BF6168 6 SCREW 3/8 X 1 NC
4 00012101 6 LOCKWASHER 3/8 PL HVY
5 00757359 1 BRACE STRAP
6 7A121016 1 C/S 3/4 X 2 NC ZP
7 00003901 1 LOCKWASHER 3/4 PL HEAVY
8 00000200 1 NUT 3/4 NC HEX PL
9 15B1200 1 WASHER 3/4 P SAE
10 20A4012E 1 PIN
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 76
WINCH AND STAND ASSSEMBLY S/N 00101 - 10429 OCT 1977 - MAY 1988
ITEM PART NO. QTY. DESCRIPTION
1 0656200100 1 STAND WINCH FS15
2 00011400 3 HHCS 3/8 NC 1 PL5
3 00748823 2 HHCS 1/2-13UNC 1-1/2 PL5
4 15B600 1 WASHER 3/8 SAE P
5 00012101 3 LOCKWASHER 3/8 PL HVY
6 00001300 2 LOCKWASHER 1/2 PL STD
7 00013901 3 NUT HEX 3/8 NC PL
8 00001200 2 NUT,HEX 1/2 NC PL
9 B651202 1 WINCH & CABLE
10 651202 1 WINCH
11 651203 1 CABLE, 1/4 AIRCRAFT W/THIMBLE
12 65111 1 BAR, TRANSPORT
13 37107B13 2 CLIP-X HAIR PIN
Note: this winch will fit and work in place of all previous winches with no modifications.
FS15 Master Parts Book (July-05)
©2005 Alamo Group Inc. Parts Section – 77
LIMITED WARRANTY
1. LIMITED WARRANTIES
1.01.Servis-Rhino warrants for one year from the purchase date to the original non-commercial, governmental, or municipal
purchaser (“Purchaser”) and warrants for six months to the original commercial or industrial purchaser (“Purchaser”)
that the goods purchased are free from defects in material or workmanship.
1.02.Manufacturer will replace for the Purchaser any part or parts found, upon examination at one of its factories, to be
defective under normal use and service due to defects in material or workmanship.
1.03.This limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use,
negligence, alteration, modification, or accident, damaged due to lack of maintenance or use of wrong fuel, oil, or
lubricants, or which has served its normal life. This limited warranty does not apply to any part of any internal
combustion engine, or expendable items such as blades, shields, guards, or pneumatic tires except as specifically found
in your Operator’s Manual.
1.04.Except as provided herein, no employee, agent, Dealer, or other person is authorized to give any warranties of any
nature on behalf of Manufacturer.
2. REMEDIES AND PROCEDURES.
2.01.This limited warranty is not effective unless the Purchaser returns the Registration and Warranty Form to Manufacturer
within 30 days of purchase.
2.02.Purchaser claims must be made in writing to the Authorized Dealer (“Dealer”) from whom Purchaser purchased the
goods or an approved Authorized Dealer (“Dealer”) within 30 days after Purchaser learns of the facts on which the
claim is based.
2.03.Purchaser is responsible for returning the goods in question to the Dealer.
2.04.If after examining the goods and/or parts in question, Manufacturer finds them to be defective under normal use and
service due to defects in material or workmanship, Manufacturer will:
(a) Repair or replace the defective goods or part(s) or
(b) Reimburse Purchaser for the cost of the part(s) and reasonable labor charges (as determined by Manufacturer)
if Purchaser paid for the repair and/or replacement prior to the final determination of applicability of the warranty
by Manufacturer.
The choice of remedy shall belong to Manufacturer.
2.05.Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by Manufacturer and
for returning the goods to the Dealer, whether or not the claim is approved. Purchaser is responsible for the trans-
portation cost for the goods or part(s) from the Dealer to the designated factory.
3. LIMITATION OF LIABILITY.
3.01.MANUFACTURER DISCLAIMS ANY EXPRESS (EXCEPT AS SET FORTH HEREIN) AND IMPLIED WARRANTIES
WITH RESPECT TO THE GOODS INCLUDING, BUT NOT LIMITED TO, MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE.
3.02.MANUFACTURER MAKES NO WARRANTY AS TO THE DESIGN, CAPABILITY, CAPACITY, OR SUITABILITY FOR
USE OF THE GOODS.
3.03.EXCEPT AS PROVIDED HEREIN, MANUFACTURER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO
PURCHASER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS, OR DAMAGE
CAUSED OR ALLEGED TO BE CAUSED DIRECTLY OR INDIRECTLY BY THE GOODS INCLUDING, BUT NOT
LIMITED TO, ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES RESULTING FROM
THE USE OR OPERATION OF THE GOODS OR ANY BREACH OF THIS WARRANTY. NOT WITHSTANDING THE
ABOVE LIMITATIONS AND WARRANTIES, MANUFACTURER’S LIABILITY HEREUNDER FOR DAMAGES
INCURRED BY PURCHASER OR OTHERS SHALL NOT EXCEED THE PRICE OF THE GOODS.
3.04.NO ACTION ARISING OUT OF ANY CLAIMED BREACH OF THIS WARRANTY OR TRANSACTIONS UNDER
THIS WARRANTY MAY BE BROUGHT MORE THAN TWO (2) YEARS AFTER THE CAUSE OF ACTION HAS
OCCURRED.
4. MISCELLANEOUS.
4.01.Proper Venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe County,
Texas.
4.02.Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall
be deemed to be a waiver of any other term.
4.03.If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the
invalidity of such provision shall not invalidate any other provisions herein.
4.04.Applicable law may provide rights and benefits to purchaser in addition to those provided herein.
KEEP FOR YOUR RECORDS
ATTENTION: Purchaser should fill in the blanks below for his reference when buying repair parts and/or for proper machine
identification when applying for warranty.
Servis-Rhino Implement Model _______________________________ Serial Number ________________________________
Date Purchased __________________________________________ Dealer ______________________________________
ATTENTION:
READ YOUR OPERATOR'S MANUAL
SERVIS-RHINO
1020 S. Sangamon Ave.
Gibson City, IL 60936
800-446-5158
Email: parts@servis-rhino.com
RHINO®
TO THE OWNER/OPERATOR/DEALER
To keep your implement running efficiently and safely, read your manual thoroughly and follow these directions and
the Safety Messages in this Manual. The Table of Contents clearly identifies each section where you can easily
find the information you need.
The OCCUPATIONAL SAFETY AND HEALTH ACT (1928.51 Subpart C) makes these minimum safety
requirements of tractor operators:
REQUIRED OF THE OWNER:
1. Provide a Roll-Over-Protective Structure that meets the requirements of this Standard; and
2. Provide Seatbelts that meet the requirements of this paragraph of this Standard and SAE J4C; and
3. Ensure that each employee uses such Seatbelt while the tractor is moving; and
4. Ensure that each employee tightens the Seatbelt sufficiently to confine the employee to the protected
area provided by the ROPS.
REQUIRED OF THE OPERATOR
1. Securely fasten seatbelt if the tractor has a ROPS.
2. Where possible, avoid operating the tractor near ditches, embankments, and holes.
3. Reduce speed when turning, crossing slopes, and on rough, slick, or muddy surfaces.
4. Stay off slopes too steep for safe operation.
5. Watch where you are going - especially at row ends, on roads, and around trees.
6. Do not permit others to ride.
7. Operate the tractor smoothly - no jerky turns, starts, or stops.
8. Hitch only to the drawbar and hitch points recommended by the tractor manufacturer.
9. When the tractor is stopped, set brakes securely and use park lock, if available.
Keep children away from danger all day, every day...
Equip tractors with rollover protection (ROPS) and keep all machinery
guards in place...
Please work, drive, play and live each day with care and concern for
your safety and that of your family and fellow citizens.
Printed U.S.A.
FS15 PL 07-05 P/N 00773425MB

Navigation menu