Sharp HRO00025 Cordless Telephone System User Manual Table
Sharp Corporation Cordless Telephone System Table
Sharp >
Contents
- 1. Users Manual 1
- 2. Users Manual 2
- 3. Users Manual 3
- 4. Replacement page of manual
Users Manual 1
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 236374 |
| Application ID | QQkwO9ccL2V2wLG8d/+XJQ== |
| Document Description | Users Manual 1 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 149.13kB (1864090 bits) |
| Date Submitted | 2002-04-11 00:00:00 |
| Date Available | 2002-06-03 00:00:00 |
| Creation Date | 2002-03-29 11:20:13 |
| Producing Software | Acrobat PDFWriter 4.05 Windows |
| Document Lastmod | 2002-03-29 11:21:00 |
| Document Title | æ©¡Table.PDF |
| Document Creator | æ©¡Microsoft Word |
| Document Author: | æ©¡IKEZAWA |
UX-CL220
MODEL
UX-CL220
FACSIMILE
CSI
FA
OPER
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Installation
Setting Up and Using OpenLCR
Using the Answering System
Using the Cordless Handset
Sending Faxes
Receiving Faxes
Making Copies
Special Functions
Printing Lists
Maintenance
Troubleshooting
ANUA
NM
ATIO
all.book
Page 1
Wednesday, February 13, 2002
10:00 AM
WARNING - FCC Regulations state that any unauthorized changes or modifications to this equipment
not expressly approved by the manufacturer could void the user’s authority to operate this equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
IMPORTANT NOTICE
Fax machine
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for at uncontrolled
equipment.
This equipment should be installed and operated with minimum distance at least 20cm
between the radiator and persons body (excluding extremities: hands, wrists, feet and legs)
and must not be co-located or operated with any other antenna or transmitter.
Cordless handset
For body worn operation, this phone has been tested and meets FCC RF exposure gudelines
when used with an accessory that no metal and that positions the handset a minimum of
1.5cm from the body.
Use of other accessories may not ensure compliance with FCC RF exposure guidelines.
ABOUT THE TELEPHONE CONSUMER PROTECTION ACT OF 1991
"The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a
computer or other electronic device to send any message via a telephone facsimile machine
unless such message clearly contains in a margin at the top or bottom of each transmitted
page or on the first page of the transmission the following information:
(1) The date and time of transmission.
(2) Identification of either the business, business entity or individual sending the message.
(3) Telephone number of either the sending machine, business, business entity or individual.
In order to program this information into your facsimile machine, please refer to the
appropriate instructions in the operation manual."
As an ENERGY STAR partner, SHARP has
determined that this product meets the ENERGY
STAR guidelines for energy efficiency.
all.book
Page 1
Wednesday, February 13, 2002
10:00 AM
Introduction
Welcome, and thank you for
choosing a Sharp fax
machine! The features and
specifications of your new
Sharp fax are shown below.
Fax machine and general specifications.
Automatic dialing
30 numbers
Imaging film
Initial starter roll (included with machine):
32 ft. (10 m) (approx. 30 letter-size pages)
Replacement roll (not included):
UX-5CR 164 ft. (50 m) (one roll yields
approx. 150 letter-size pages)
Memory size*
504 KB (approx. 30 average pages with no
voice messages recorded and ECM turned
off, or 20 minutes of voice messages
(including OGMs) with no faxes in memory)
Modem speed
14,400 bps with automatic fallback to lower
speeds.
Transmission time*
Approx. 6 seconds (only when ECM is on)
Resolution
Horizontal: 203 pels/inch (8 pels/mm)
Vertical:
Standard: 98 lines/inch (3.85 lines/mm)
Fine /Halftone:
196 lines/inch (7.7 lines/mm)
Super fine:
391 lines/inch (15.4 lines/mm)
Automatic document
feeder
10 pages max. (letter/A4, 20 lb paper)
Recording system
Thermal transfer recording
Display
16-digit LCD display
*Based on Sharp Standard No. 1 Chart at standard resolution in Sharp special mode,
excluding time for protocol signals (i.e., ITU-T phase C time only).
all.book
Page 2
Wednesday, February 13, 2002
10:00 AM
Halftone (grayscale)
64 levels
Compression scheme
MR, MH, MMR
Applicable telephone line Public switched telephone network
Paper tray capacity
Letter: Approx. 50 sheets (20-lb. copier paper
at room temperature; maximum stack height
should not be higher than the line on the tray)
Legal: 5 sheets
Recommended paper weight: 20-lb. Copy
Bond
Compatibility
ITU-T (CCITT) G3 mode
Input document size
Automatic feeding:
Width: 5.8 to 8.5" (148 to 216 mm)
Length: 5.5 to 11" (140 to 279 mm)
Manual feeding:
Width: 5.8 to 8.5" (148 to 216 mm)
Length: 5.5 to 23.6" (140 to 600 mm)
Effective scanning width
8.3" (210 mm) max.
Effective printing width
8.3" (210 mm) max.
Contrast control
Automatic/Dark selectable
Reception modes
TEL/FAX/TAD
Copy function
Single / Multi (99 copies/page)
Telephone function
Yes (cannot be used if power fails)
Power requirements
120 V AC, 60 Hz
Operating temperature
41 - 95°F (5 - 35°C)
Humidity
25 - 85% RH
Power consumption
Standby: 4.3 W
Maximum: 100 W
Dimensions (without
attachments)
Width: 13.9" (353 mm)
Depth: 7.6" (193 mm)
Height: 6.9" (174 mm)
Weight (without
attachments)
Approx. 6.2 lbs. (2.8 kg)
all.book
Page 3
Wednesday, February 13, 2002
10:00 AM
Cordless handset specifications.
Frequency
2.4 GHz (2.405 to 2.475 GHz)
Dimensions
Width: 1.8" (46 mm)
Depth: 1.7" (42 mm)
Height: 7.1" (180 mm) (not including antenna)
Weight
Approx. 0.3 lbs. (115 g) (without battery)
Battery
3.6 V Ni-MH battery; capacity: 850 mAh
Power consumption
Initial charging
Battery life
Battery life in standby
mode
Approx. 1.0 W (in standby mode)
Approx. 10 hours for initial charge
Approx. 4 hours (240 minutes) (at room
temperature)
Approx. 3 days with one full charge (at room
temperature)
Battery life (both normal and in standby
mode) may vary depending on usage, range
from base machine, and environmental
conditions such as temperature.
As a part of our policy of continuous improvement, SHARP reserves the right to make
design and specification changes for product improvement without prior notice. The
performance specification figures indicated are nominal values of production units. There
may be some deviations from these values in individual units.
Important:
This fax machine is not designed for use on a line which has call waiting, call forwarding,
or certain other special services offered by your telephone company. If you attempt to use
the fax machine in conjunction with any of these services, you may experience errors
during transmission and reception of facsimile messages. The fax machine is not
compatible with digital telephone systems.
Important safety information
Do not disassemble this machine or attempt any procedures not described in this manual.
Refer all servicing to qualified service personnel.
Do not install or use the machine near water, or when you are wet. For example, do not
use the machine near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet
basement, or near a swimming pool. Take care not to spill any liquids on the machine.
Unplug the machine from the power outlet and telephone jack and consult a qualified
service representative if any of the following situations occur:
- Liquid has been spilled into the machine or the machine has been
exposed to rain or water.
- The machine produces odors, smoke, or unusual noises.
all.book
Page 4
Wednesday, February 13, 2002
10:00 AM
- The power cord is frayed or damaged.
- The machine has been dropped or the housing damaged.
Do not allow anything to rest on the power cord, and do not install the machine where
people may walk on the power cord.
This machine must only be connected to a 120 V, 60 Hz, grounded (3-prong) outlet.
Connecting it to any other kind of outlet will damage the machine and invalidate the
warranty.
Never insert objects of any kind into slots or openings on the machine. This could create a
risk of fire or electric shock. If an object falls into the machine that you cannot remove,
unplug the machine and consult a qualified service representative.
Do not place this machine on an unstable cart, stand or table. The machine could be
seriously damaged if it falls.
Never install telephone wiring during a lightning storm.
Never install telephone jacks in wet locations unless the jack is specifically designed for
wet locations.
Never touch bare telephone wires or terminals unless the telephone line has been
disconnected at the network interface.
Use caution when installing or modifying telephone lines.
Avoid using a telephone (other than a cordless type) during an electrical storm. There
may be a remote risk of electric shock from lightning.
Do not use a telephone to report a gas leak in the vicinity of the leak.
The power outlet must be installed near the equipment and must be easily accessible.
Battery
Use only the battery specified in this manual. Use only the provided charger to charge the
battery.
Do not open or mutilate the battery pack. Corrosive fluid may leak out and cause injury or
burns to the eyes and skin. The fluid may be toxic if swallowed. In case of contact with
eyes, flush with clean water (do not rub), and seek medical attention immediately.
Do not store or carry the battery with other metal objects such as keys or pins. These may
short the battery and cause it to overheat.
Do not allow the battery to become wet.
Do not dispose of the battery in a fire or heat the battery. The battery may explode.
Health care facilities and equipment
Radio frequency energy emitted from the cordless handset equipment may cause
medical equipment to malfunction. Verify that any personal medical equipment you are
using is adequately shielded from external radio frequency energy before using the
cordless handset equipment. Do not use the cordless handset equipment in health care
facilities where such use is prohibited.
all.book
Page 5
Wednesday, February 13, 2002
10:00 AM
Table of Contents
A Look at the Operation Panel
1. Installation
Unpacking Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting Up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Loading the Imaging Film . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Loading Printing Paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Entering Your Name and Fax Number . . . . . . . . . . . . . . . . . . . . . . .
Setting the Date and Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the Reception Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Volume Adjustment - Fax Machine. . . . . . . . . . . . . . . . . . . . . . . . . .
Volume Adjustment - Cordless Handset. . . . . . . . . . . . . . . . . . . . . .
12
12
13
21
23
25
27
29
30
31
2. Setting Up and Using OpenLCR
33
3. Using the Answering System
43
Recording an Outgoing Message . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating the Answering System . . . . . . . . . . . . . . . . . . . . . . . . . . .
Optional Answering System Settings . . . . . . . . . . . . . . . . . . . . . . . .
Transfer Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Override Ringing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4. Using the Cordless Handset
43
44
48
50
53
55
61
Making a Phone Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Receiving a Phone Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Receiving a Fax Using the Cordless Handset . . . . . . . . . . . . . . . . . 63
Storing and Using Auto-Dial Numbers . . . . . . . . . . . . . . . . . . . . . . . 63
Redial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Using the Intercom Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Transferring Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Using REMOTE MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
5. Sending Faxes
73
Transmittable Documents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
all.book
Page 6
Wednesday, February 13, 2002
10:00 AM
Table of Contents
Loading the Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Adjusting the Resolution and Contrast . . . . . . . . . . . . . . . . . . . . . . . 75
Sending a Fax by Normal Dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Sending a Fax by Automatic Dialing . . . . . . . . . . . . . . . . . . . . . . . . . 78
Sending a Fax From Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
6. Receiving Faxes
87
Using FAX Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Using TEL Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Optional Reception Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Substitute Reception to Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
7. Making Copies
93
8. Special Functions
95
Caller ID (Requires Subscription to Service) . . . . . . . . . . . . . . . . . . 95
Distinctive Ring (Requires Subscription to Service) . . . . . . . . . . . . 101
Blocking Reception of Unwanted Faxes . . . . . . . . . . . . . . . . . . . . . 102
9. Printing Lists
103
10. Maintenance
107
Replacing the Cordless Handset Battery . . . . . . . . . . . . . . . . . . . . 110
11. Troubleshooting
112
Problems and Solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Messages and Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Clearing Paper Jams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Ordering Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
FCC Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Quick Reference Guide
129
Guía de referencia rápida
131
Index
133
all.book
Page 7
Wednesday, February 13, 2002
10:00 AM
A Look at the Operation Panel
ABC
UP
TEL FAX
REC/
MEMO
PLAY
GHI
INTERCOM
RESOLUTION/ REDIAL
RECEPTION MODE
STOP
COPY/HELP START/MEMORY
FUNCTION
10 11 12 13
PQRS
14
15
MNO
TUV
WXYZ
SPEAKER
D OW N
JKL
OpenLCR
DEF
TAD
REPEAT
SKIP
16
17
DELETE
18
Display
This displays messages and prompts to help you operate the machine.
INTERCOM key
Press this key to page or locate the cordless handset.
REC/MEMO key
Press this key to record an outgoing message, phone conversation, or memo.
PLAY key
Press this key to play recorded messages.
Left and right arrow keys
Auto-dial numbers: When sending a fax or making a phone call, press these
keys to scroll through your auto-dial numbers, the “REVIEW CALLS” list (only
available if you have Caller ID), and the last number dialed (redial).
FUNCTION key settings: Press the right arrow key after scrolling with the up
and down arrow keys to select a FUNCTION key setting.
Number keys
Use these keys to dial numbers, and enter numbers and letters when storing
auto-dial numbers.
Panel release
Press this release to open the operation panel.
STOP key
Press this key to cancel an operation before it is completed.
all.book
Page 8
Wednesday, February 13, 2002
10:00 AM
COPY/HELP key
When a document is in the feeder, press this key to make a copy of a
document. At any other time, press this key to print out the Help List, a quick
reference guide to the operation of your fax machine.
10
START/MEMORY key
Press this key after dialing to begin fax transmission. Press this key before
dialing to send a fax through memory. The key can also be pressed in the date
and time display to show the percentage of memory currently used.
11
RESOLUTION / RECEPTION MODE key
When a document is in the feeder, press this key to adjust the resolution for
faxing or copying. At any other time, press this key to select the reception
mode (an arrow in the display will point to the currently selected reception
mode).
12
FUNCTION key
Press this key followed by the arrow keys to select special functions and
settings.
13
OpenLCR key
Press this key to register for OpenLCR service and receive rate information to
your fax.
14
UP and DOWN arrow keys
Enlarge/reduce setting: When making a copy of a document, press these
keys to select an enlarge/reduce setting.
Volume setting: When a document is not in the feeder, press these keys to
change the handset volume when the handset is lifted, the speaker volume
when the SPEAKER key has been pressed, or the ringer volume at any other
time.
FUNCTION key settings: Press these keys after pressing the FUNCTION
key to scroll through the FUNCTION MODE settings.
15
SPEAKER key
Press this key to listen to the line and fax tones through the speaker when
faxing a document.
Note: This is not a speakerphone. You must pick up the handset to talk with
the other party.
16
REPEAT key
Press this key while listening to a message to play it again.
17
SKIP key
Press this key while listening to a message to skip to the next message.
18
DELETE key
Press this key to erase recorded messages.
all.book
Page 9
Wednesday, February 13, 2002
10:00 AM
12
13
FUNCTION
/PAUSE
REVIEW
START
REMOTE
/FLASH
DOWN
GHI
14
22
SEARCH
OFF
TALK
ABC
DEF
JKL
MNO
15
16
23
RECEPTION
PQRS
PLAY
TUV
PLAY NEW
WXYZ
STOP
REPEAT
10
UP
INTER
COM
SKIP
DELETE
REDIAL
HOLD
17
18
19
ERASE
11
20
21
Antenna
Display
This displays messages and prompts to help you use the cordless handset.
UP and DOWN arrow keys
Receiver volume: When talking on the cordless handset, press these keys to
adjust the receiver volume. This also adjusts the volume when using a
headset (purchased separately) connected to the cordless handset.
Ringer volume: When not talking on the cordless handset, press these keys
to adjust the cordless handset ringer volume.
Scroll through numbers: Press these keys to scroll when searching for an
auto-dial number or reviewing received calls (only available when you have
Caller ID).
FUNCTION/PAUSE key
Press this key to after pressing
SEARCH to store a new auto dial number.
When entering an auto-dial number, press this key to insert a pause between
digits.
all.book
Page 10
Wednesday, February 13, 2002
10:00 AM
TALK key
Press this key to make or answer a call.
REVIEW (left) arrow key
Press the REVIEW arrow key and then the UP or DOWN arrow key to scroll
through your 30 most recent calls (only available if you have Caller ID). This
key can also be used to move the cursor left when entering or editing an autodial number or name.
Number keys
Use these keys to dial numbers, and enter numbers and letters when storing
auto-dial numbers.
PLAY NEW key
Press this key after pressing
REMOTE
/FLASH
to listen to new messages recorded in the
answering system.
PLAY key
Press this key after pressing
REMOTE
/FLASH
to listen to all messages recorded in the
answering system.
10
REPEAT key
Press this key while listening to a message to play it again.
11
INTERCOM key
Press this key to page the fax machine.
12
START key
Press this key to start fax reception from the cordless handset, or to complete
entries when storing, editing, or deleting auto-dial numbers.
13
REMOTE/FLASH key
Press this key to perform remote operations on the fax machine. The key is
also used to access special services from your phone company that require
subscription (contact your phone company for details).
14
OFF key
Press this key to end a call.
15
SEARCH (right) arrow key
Press the SEARCH arrow key and then the UP or DOWN arrow key to scroll
through your auto-dial numbers. This key can also be used to move the cursor
right when entering or editing an auto-dial number or name.
10
all.book
16
Page 11
Wednesday, February 13, 2002
10:00 AM
RECEPTION key
Press this key after pressing
REMOTE
/FLASH
to change the reception mode on the fax
machine.
17
STOP key
Press this key to stop playback of messages recorded in the answering
system.
18
DELETE
Press this key while listening to a message to delete it. To delete all your
messages, press this key after playback ends (while the display shows
REMOTE MODE), followed by
START
19
HOLD/ERASE key
Hold: Press this key during a call to put the other party on hold.
Erase: Press this key to delete a phone number when searching through your
recently received calls (only when you have Caller ID), or when searching
through your auto-dial numbers. Press the key to delete a digit or character
when storing or editing an auto-dial number.
20
SKIP key
Press this key while listening to your messages to skip to the next message.
21
REDIAL key
Press this key to redial the last number dialed using the cordless handset.
22
Headset jack
This jack lets you connect a headset (purchased separately) to the cordless
handset.
23
Battery cover
Remove this cover to install or replace the handset battery.
11
all.book
Page 12
Wednesday, February 13, 2002
10:00 AM
1. Installation
Unpacking Checklist
Before setting up,
make sure you
have all of the
following items.
If any are missing,
contact your
dealer or retailer.
Paper tray
Paper tray
extension
Operation
manual
Gears (2)
Handset
Handset
cord
Telephone
line cord
Imaging film
(initial starter roll)
Cordless
handset
12
Battery
cover
Battery
pack
AC adapter
Cordless
handset charger
Page 13
Wednesday, February 13, 2002
10:00 AM
Setting Up
Setting Up
Selecting a location for the fax machine
To maximize the talking range of the cordless handset and minimize
interference, we recommend installing the fax machine in a high and central
location away from obstructions such as walls.
High and central
location with no
obstructions
Keep the fax machine away
from other electrical
appliances such as TVs,
microwave ovens,
computers, and other
cordless phones.
Do not place the
machine in direct
sunlight.
Do not place the
machine near
heaters or air
conditioners.
Keep dust away from
the machine.
Keep the area
around the
machine clear.
13
1. Installation
all.book
all.book
Page 14
Wednesday, February 13, 2002
10:00 AM
Setting Up
Connecting the handset
Connect the handset as shown and place it on the handset rest.
♦ The ends of the handset cord are identical, so they will go into either jack.
Make sure the handset
cord goes into the jack
marked with a handset
symbol on the side of
the machine!
Use the handset to make ordinary phone calls,
or to transmit and receive faxes manually.
Connecting the power cord
Plug the power cord into a 120 V, 60 Hz, grounded AC (3-prong) outlet.
Caution!
Do not plug the power cord into any other kind of outlet. This will damage the
machine and is not covered under the warranty.
The machine does not
have a power on/off
switch, so the power is
turned on and off by
simply plugging in or
unplugging the power
cord.
14
Page 15
Wednesday, February 13, 2002
10:00 AM
Setting Up
Connecting the telephone line cord
Insert one end of the line cord into the jack on the back of the machine
marked TEL. LINE. Insert the other end into a standard (RJ11C) single-line
wall telephone jack.
TE
L.L
INE
Setting the dial mode
The fax machine is set for tone dialing. If you are on a pulse dial line, you must
set the fax machine for pulse dialing. Press the panel keys as follows:
Press
FUNCTION
once and
twice.
Display:
OPTION SETTING
Press
once and
Press
once.
Select the dial mode:
TONE:
Press
STOP
PULSE:
twice.
DIAL MODE
1=TONE, 2=PULSE
The display briefly shows
your selection, then:
DISTINCTIVE
to exit.
15
1. Installation
all.book
all.book
Page 16
Wednesday, February 13, 2002
10:00 AM
Setting Up
Note: If your area experiences a high incidence of lightning or power surges,
we recommend that you install surge protectors for the power and telephone
lines. Surge protectors can be purchased at most telephone specialty stores.
About condensation
If the machine is moved from a cold to a warm place, it is possible that
condensation may form on the scanning glass, preventing proper scanning of
documents for transmission. To remove the condensation, turn on the power and
wait approximately two hours before using the machine.
Attach the paper tray and paper tray extension
Attach the paper tray.
Attach the paper tray extension.
Click!
Insert
horizontally
and rotate up
Note: The paper tray extension has a top side
and a bottom side. If the tabs do not go into
the holes, turn the support over.
16
Page 17
Wednesday, February 13, 2002
10:00 AM
Setting Up
Raising the base antenna
Raise the base antenna to ensure clear communication with the cordless
handset.
Connecting the cordless handset charger
Connect the AC adapter to the cordless
handset charger.
Fit the cord into
the holders.
Plug the AC adapter into a standard
120 V AC outlet.
Important: Never cover the charger and AC adapter with a blanket, cloth, or
other material. Excessive heating may result and cause fire.
17
1. Installation
all.book
all.book
Page 18
Wednesday, February 13, 2002
10:00 AM
Setting Up
Installing the battery and charging the cordless handset
Connect the battery connector ➊, and then place the battery pack in the
cordless handset.
• Place the wires as shown.
Red
Black
Red
Black
Place the battery cover on the cordless
handset, making sure it snaps firmly
into place.
• Make sure the wires are not caught or
pinched by the cover.
Place the cordless handset in the
charger with the dial pad facing
forward.
• Important! The dial pad must face
forward, or the battery will not charge.
• The battery charges automatically while
the cordless handset is in the charger.
While charging, the display shows
CHARGING. When charging is
completed, the display shows IN
CHARGER.
• The cordless handset and charger may
Charge the battery
at least 10 hours
the first time!
feel warm while charging. This is
normal.
The battery cannot be overcharged. When not using the cordless handset,
keep it in the charger to ensure that it is always charged.
18
Page 19
Wednesday, February 13, 2002
10:00 AM
Setting Up
When the battery needs charging, LOW BATTERY will appear in the display
and you will hear beeps during a phone conversation. If you need to continue
the conversation, press
INTER
COM
to transfer the call to the fax machine. Place the
cordless handset in the charger and let it charge.
Note: If the battery is extremely low, nothing may appear in the display during
the first several minutes that the cordless handset is in the charger. The
battery will begin to charge normally after several minutes.
To ensure that the battery
charges properly, wipe the
charger contacts once a
month with a cotton swab.
Talking range
The talking range of the cordless handset is approximately 1200 ft. (400 m)
(line of sight). If you hear noise or interference while talking on the cordless
handset, move closer to the fax machine.
♦ When outside the talking range, OUT OF RANGE appears in the display. If
you move out of the talking range while talking on the cordless handset,
the handset will beep and you may hear interference.
Aluminum sash
Metal
Reinforced concrete
Large metal objects,
metal structures, and
thick walls reduce the
talking range.
19
1. Installation
all.book
all.book
Page 20
Wednesday, February 13, 2002
10:00 AM
Setting Up
Connecting a headset
You can connect a headset (purchased separately) to the headset jack.
Remove the cap and insert the connector as shown.
20
Page 21
Wednesday, February 13, 2002
10:00 AM
Loading the Imaging Film
Loading the Imaging Film
Your fax uses a roll of imaging film to create printed text and images. The print
head in the fax applies heat to the imaging film to transfer ink to the paper.
Follow the steps below to load or replace the film.
The initial starter roll of
imaging film included with
your fax can print about
30 letter-size pages.
When replacing the film,
use a roll of Sharp UX5CR imaging film. One
roll can print about 150
letter-size pages.
Use only Sharp Genuine
Supplies with this logo:
Remove the paper from the paper tray
and open the operation panel (press
➊).
If you are loading the imaging film for
the first time, go to Step 4.
Remove the used film and
empty spool.
Remove the two green gears from the
spools.
DO NOT DISCARD THE TWO GREEN
GEARS!
21
1. Installation
all.book
isif.fm
Page 22
Tuesday, February 19, 2002 8:45 AM
Loading the Imaging Film
Remove the new roll of imaging film
from its packaging.
• Cut the band that holds the rolls
together.
Insert the green gears.
1 slot
Make sure the
gears fit into the
slots in the ends
of the rolls.
Insert the film into the print
compartment.
2 slots
Fit ends of rolls
onto hubs
Thick roll
to rear
22
Rotate the front gear as shown until
the film is taut.
Close the operation panel (press down
on both sides to make sure it clicks
into place).
Page 23
Wednesday, February 13, 2002
10:00 AM
Loading Printing Paper
Loading Printing Paper
You can load letter or legal size paper in the paper tray. Recommended paper
weight is 20-lb. Copy Bond. The maximum number of sheets is as follows:
Letter size:
Legal size:
Approx. 50 sheets (20-Ib. copier paper at room temperature;
maximum stack height should not be higher than the line on the
tray)
5 sheets
Fan the paper, and then tap the edge
against a flat surface to even the stack.
Make sure the stack edges are even.
Insert the stack of paper into the tray, PRINT SIDE DOWN.
• If paper remains in the tray, take it out and combine it into a single stack
with the new paper.
• Be sure to load the paper so that printing takes place on the print side of
the paper. Printing on the reverse side may result in poor print quality.
• GENTLY LOAD PAPER INTO THE PAPER TRAY.
• DO NOT FORCE IT DOWN INTO THE FEED SLOT.
The stack
should not
be higher
than this line
Note: Do not use paper that has already been printed on, or paper that is curled.
Note: If at any time the display shows the
alternating messages at right, check the printing
paper. If the tray is empty, add paper. If there is
paper in the tray, take it out and then reinsert it.
When you are finished, press
START/MEMORY
ADD PAPER &
PRESS START KEY
23
1. Installation
all.book
all.book
Page 24
Wednesday, February 13, 2002
10:00 AM
Loading Printing Paper
Setting the paper size
The fax has been set at the factory to scale received faxes to letter size paper.
If you loaded legal paper, you must change the paper size setting to LEGAL.
Press
Press
once and
Press
once.
Select the paper size:
FUNCTION
LETTER:
Press
once and
STOP
Display:
twice.
OPTION SETTING
PAPER SIZE SET
1=LETTER,2=LEGAL
LEGAL:
twice.
The display briefly shows
your selection, then:
COPY CUT-OFF
to return to the date and time display.
Print contrast setting
Your fax has been set at the factory to print at normal contrast. If desired, you
can change the print contrast setting to LIGHT.
Press
Press
once and
Press
once.
Select the print contrast:
FUNCTION
NORMAL:
24
Press
STOP
once and
twice.
3 times.
Display:
OPTION SETTING
PRINT CONTRAST
1:NORMAL
LIGHT:
The display briefly shows
your selection, then:
PAPER SIZE SET
to return to the date and time display.
Page 25
Wednesday, February 13, 2002
10:00 AM
Entering Your Name and Fax Number
Entering Your Name and Fax Number
Before you can begin sending
faxes, you must enter your
name and fax (telephone)
number. You also need to set
the date and time.
Once you enter this
information, it will
automatically appear at
the top of each fax page
you send.
Important!
FCC regulations require that your name, telephone/fax number, and the date and
time appear on each fax message you send. Enter your name and fax number
here and set the date and time as explained in the following section to have the fax
machine include this information automatically at the top of your fax messages.
STOP
START/MEMORY
Press
FUNCTION
once and
FUNCTION
3 times.
Display:
ENTRY MODE
Press
once.
Press
once.
OWN NUMBER SET
ENTER FAX #
25
1. Installation
all.book
all.book
Page 26
Wednesday, February 13, 2002
10:00 AM
Entering Your Name and Fax Number
Enter your fax number by pressing the number keys (max. 20 digits).
• To insert a space between digits, press
• To clear a mistake, press
START/MEMORY
SPEAKER
Press
Enter your name by pressing number keys for each letter as shown in
the chart below. Up to 24 characters can be entered.
to enter the fax number in memory.
Example: SHARP = 7777 44 2 777
G=
N=
A=
H=
O=
V=
B=
I =
P=
W=
C=
J=
Q=
X=
D=
K=
R=
Y=
E=
L=
S=
Z=
F=
M=
T=
SPACE =
U=
♦ To enter two letters in succession that require the same key, press
after entering the first letter.
♦ To clear a mistake, press
SPEAKER
♦ To enter a lower case letter, continue pressing the key for the letter until the
lower case letter appears. To enter one of the following symbols, press
or
26
Press
Press
repeatedly: . / ! " # $ % & ’ ( ) + + , - : ; < = > ? @ [ ¥ ] ^ _ ' { | } ) (
START/MEMORY
STOP
Display:
DATE&TIME SET
to return to the date and time display.
Page 27
Wednesday, February 13, 2002
10:00 AM
Setting the Date and Time
Setting the Date and Time
The date and time appear
in the display and are
printed at the top of every
page you fax. Set the date
and time as shown below.
Do not set the date
and time if you are
using OpenLCR!
OpenLCR
automatically sets the
date and time each
time your fax calls
OpenLCR and
receives rate data. To
ensure accurate use
of the rate data, do not
change the date and
time setting yourself.
STOP
START/MEMORY
FUNCTION
Press
Press
Press
Enter a two-digit number for the month (“01” for January, “02” for
February, “12” for December, etc.).
FUNCTION
once and
3 times.
once and
once.
• To correct a mistake, press
ENTRY MODE
DATE&TIME SET
The currently set date
appears (example):
Example: January
Display:
DATE 08-15-2002
DATE 01-15-2002
to move the cursor back to the mistake and
then enter the correct number.
Enter a two-digit number for the day (“01” to “31”).
Example: the 5th
DATE 01-05-2002
27
1. Installation
all.book
all.book
Page 28
Wednesday, February 13, 2002
10:00 AM
Setting the Date and Time
Example: 2002
The currently set time
appears (example):
Enter the year (four digits).
TIME 12:19 PM
Enter a two-digit number for the hour (“01” to “12”) and a two-digit
number for the minute (“00” to “59”).
Example: 9:25
Press
Press
10
Press
to select A.M. or
START/MEMORY
STOP
TIME 09:25 PM
to select P.M.
ANTI JUNK #
to start the clock.
to return to the date and time display.
Daylight Saving Time
If desired, you can set the clock to move forward and backward automatically
at the beginning and end of Daylight Saving Time. Follow these steps:
28
Press
Press
once and
Press
once.
Press
Press
FUNCTION
once and
twice.
STOP
DAY LIGHT SAVE
5 times.
to select YES, or
OPTION SETTING
1=YES, 2=NO
to select NO.
RECEIVE RATIO
to return to the date and time display.
Page 29
Wednesday, February 13, 2002
10:00 AM
Setting the Reception Mode
Setting the Reception Mode
Your fax has three modes for receiving incoming faxes:
FAX mode:
Select this mode when you only want to receive faxes on your line. The fax
machine will automatically answer all calls on four rings and receive incoming
faxes.
TEL mode:
Select this mode when you want to receive both phone calls and faxes on the
line connected to the fax machine. All calls, including faxes, must be
answered by picking up the fax machine's handset or an extension phone
connected to the same line.
TAD mode:
Select this mode when you go out and want the answering system to answer
all calls. Voice messages will be recorded, and fax messages will be received
automatically (“TAD” stands for “Telephone Answering Device”.)
Setting the reception mode
Make sure a document is not loaded in the document feeder, and then
press
RESOLUTION/
RECEPTION MODE
until the arrow in the display points to the desired mode.
RESOLUTION/
RECEPTION MODE
TEL FAX
JAN-01 10:30
TAD
RESOLUTION/
RECEPTION MODE
TEL FAX
JAN-01 10:30
TAD
TEL FAX
JAN-01 10:30
TAD
Note: TAD mode cannot be selected unless a general outgoing message has
been recorded as explained on page 43.
For more information on receiving faxes in FAX and TEL modes, see Chapter
6, Receiving Faxes. For more information on using TAD mode, see Chapter 3,
Using the Answering System.
29
1. Installation
all.book
all.book
Page 30
Wednesday, February 13, 2002
10:00 AM
Volume Adjustment - Fax Machine
Volume Adjustment - Fax Machine
You can adjust the volume
of the speaker, handset,
and ringer using the up
and down arrow keys.
SPEAKER
Speaker
Press
Press
SPEAKER
• Press
or
SPEAKER
until the display shows the desired volume level.
again to turn off the speaker.
Fax machine handset
When talking through the handset,
Display:
press
or
until the display
shows the desired volume level.
RECEIVER: HIGH
• Note: The volume reverts to MIDDLE
RECEIVER: MIDDLE
each time you replace the handset.
RECEIVER: LOW
30
Page 31
Wednesday, February 13, 2002
10:00 AM
Volume Adjustment - Cordless Handset
Fax machine ringer
Display:
Press
or
until the display
shows the desired volume level.
RINGER: HIGH
SPEAKER
(Make sure
has not been
pressed, the handset is not lifted, and a
document is not loaded in the feeder.)
• The ringer rings once at the selected
level, and then the date and time
reappear in the display.
RINGER: MIDDLE
RINGER: LOW
RINGER: OFF OK ?
If you selected “RINGER: OFF OK ?” to
turn off the ringer, press
START/MEMORY
Volume Adjustment - Cordless Handset
You can adjust the volume
of the ringer and handset,
receiver using the up and
down arrow keys.
31
1. Installation
all.book
all.book
Page 32
Wednesday, February 13, 2002
10:00 AM
Volume Adjustment - Cordless Handset
Cordless handset receiver volume
When talking on the cordless handset,
Cordless handset display:
RECEIVER: HIGH
press
or
until the display
shows the desired volume level.
• Note: The volume reverts to MIDDLE
each time you hang up (press
OFF
OFF
).
RECEIVER: MIDDLE
RECEIVER: LOW
Cordless handset ringer
When you are not talking on the
cordless handset, press
or
until the display shows the desired
ringer volume level.
• The ringer will ring once at the selected
level.
Cordless handset display:
RINGER: HIGH
RINGER: MIDDLE
RINGER: LOW
RINGER: OFF OK ?
OK: PRESS START
If you selected “RINGER: OFF OK ?” to
turn off the ringer, press
32
START
all.book
Page 33
Wednesday, February 13, 2002
10:00 AM
Your fax machine features OpenLCR technology, which helps you save money
on long distance and international phone calls (both fax and voice) by
automatically routing each call for the best available rate.
♦ OpenLCR service is free of charge. The only cost to you is that of a periodic
call (usually once every three months) to OpenLCR to receive the latest
rate data. (Once you have registered with OpenLCR, your fax machine
automatically makes this call.)
♦ All calls routed by OpenLCR are consolidated on your monthly phone bill.
To take advantage of this
feature, you will need to
register with OpenLCR
and download the rate
data to your fax machine.
You can register with OpenLCR by fax, phone, or through OpenLCR’s Web
site (www.OpenLCR.com).
♦ Before registering, be sure to read the information on the openLCR
Registration form and OpenLCR TERMS OF SERVICE sheet included
with your fax machine. If you have any questions, call OpenLCR at 970206-1207.
♦ OpenLCR uses Caller ID for identification purposes when your fax calls
OpenLCR to receive rate information. Even if you have requested your
telephone company to withhold your Caller ID information when you place
calls, your fax will still automatically transmit this information only when it
calls OpenLCR.
♦ It is possible to register for and use OpenLCR if you do not subscribe to a
Caller ID service; however, in some instances where rate data must be
changed on an emergency basis, your fax may not be able to respond
automatically to OpenLCR’s call to notify your fax that it must receive new
rate data. If this occurs, old, incorrect data will continue to be used.
♦ Please note that the agreement you enter into by registering is between you
and OpenLCR; it is not between you and any carriers.
33
2. Setting Up
OpenLCR
2. Setting Up and Using OpenLCR
all.book
Page 34
Wednesday, February 13, 2002
10:00 AM
Setting Up and Using OpenLCR
Registering by fax
To register by fax, fill in the openLCR Registration form, and then fax the
form as follows:
Place the form with the side you wrote
on face down, and push it gently into
the document feeder of the fax
machine.
READY TO SEND
Press
OpenLCR
5 , and then
START/MEMORY
• Your fax automatically calls OpenLCR and sends the form. After the form
is sent, your fax will automatically receive the rate data. When downloading
is completed, the display will briefly show DOWNLOAD OK!! and then
revert to the date and time. Your fax will print out the registration form to
confirm that it was received.
• OpenLCR will also program the date and time and your fax number in your
fax machine.
Registering by phone
To register by phone, follow these steps:
34
Pick up the handset on the fax
machine.
Press
OpenLCR
and then
1 .
all.book
Page 35
Wednesday, February 13, 2002
10:00 AM
Setting Up and Using OpenLCR
If the display shows the alternating
messages at right, press the number
keys to enter your fax/phone number,
including the area code (the number
must be 10 digits long). When finished,
press
START/MEMORY
10 DIGITS
(If the message at right doesn’t appear,
this step is not necessary.)
SET OWN NUMBER
Important!
Be sure that you enter your correct
area code and fax number. If not,
your fax may not dial the correct
number to connect to OpenLCR.
Follow the instructions you hear.
♦ If you are on a pulse dial line, press
before pressing the number keys
to respond. (This makes your fax temporarily issue tone signals when you
press the number keys.)
♦ When registration is completed, your fax machine will receive the rate data
from OpenLCR. This will last one or two minutes. When downloading is
completed, the display will briefly show DOWNLOAD OK!! and then revert
to the date and time.
♦ OpenLCR will also program the date and time and your fax number in your
fax machine.
Registering through OpenLCR’s Web site
You can also register at OpenLCR’s Web site, www.OpenLCR.com. After
registering you will need to receive the rate data manually (service is not
activated until your fax receives the rate data). See Downloading (receiving)
the rate data manually on the following page.
If you move, you
must re-register!
The rate data that you receive is based
on the address you provide when
registering with OpenLCR. If you move,
the rate data will not be correct for your
new location. In this case, repeat the
registration procedure to give
OpenLCR your new address.
35
2. Setting Up
OpenLCR
all.book
Page 36
Wednesday, February 13, 2002
10:00 AM
Setting Up and Using OpenLCR
Note: If you wish to connect more than one OpenLCR-enabled device to the same
line, please call OpenLCR at 970-206-1207. If you replace an old OpenLCRenabled device with a new one, you must re-register with OpenLCR to use the new
device.
Note: OpenLCR cannot be used if your fax machine is connected to a Private
Branch Exchange (PBX).
Downloading (receiving) the rate data manually
Your fax machine will automatically call OpenLCR and download updated rate
data about once every three months. Normally you will not need to download
the rate data manually.
♦ If you register through OpenLCR’s Web site, you must manually download
the rate data to activate service.
♦ If the fax machine is unplugged or some other interruption occurs in the
power, you will need to manually download the rate data.
Press
OpenLCR
and 2
to call OpenLCR and initiate downloading. Downloading
lasts one or two minutes. During this time the display will show LCR
DOWNLOADING. When downloading is completed, the display will briefly
show DOWNLOAD OK!! and then revert to the date and time. OpenLCR will
also program the date and time and your fax number in your fax machine.
Using OpenLCR
When you have registered with OpenLCR and downloaded the rate data to
your fax machine, a highlighted “C” will appear in the date and time display to
indicate that the OpenLCR feature is activated.
TEL FAX
JAN-19 02:16
TAD
“C” indicates that
OpenLCR is activated
Each time you make a long distance phone or fax call, the fax machine will
automatically route the call through the least expensive carrier based on the
downloaded rate information.
Don’t unplug the
fax, or the rate
data will be lost!
36
Page 37
Wednesday, February 13, 2002
10:00 AM
Setting Up and Using OpenLCR
Caution! If you unplug the fax machine or an interruption occurs in your
power supply, the rate data will be erased. If this happens, the highlighted “C”
in the display will blink to alert you.The fax machine will automatically call
OpenLCR within the next 24 hours to receive new rate data; however, if you
want to use OpenLCR service before that time, you should download the rate
table manually as explained on page 36.
♦ We recommend that you do not unplug the fax machine on a regular basis
(for example at night or on the weekends), as this may result in a large
number of calls to OpenLCR and a higher phone bill.
Symbols related to OpenLCR that may appear in the display are shown below.
Mark
Meaning
OpenLCR has been activated and is ready for use.
(Blinking)
OpenLCR cannot be used because the rate data has been erased.
Your fax will automatically call OpenLCR within the next 24 hours to
receive new data, or you can download the data manually if you need
to use OpenLCR immediately (see page 36).
The rate data in the fax is no longer correct and the fax cannot connect
to OpenLCR to obtain new data. See What to do if “E” appears in the
display on page 39.
OpenLCR has been temporarily turned off. See Temporarily turning off
OpenLCR below.
Rate data was not yet available when your fax called OpenLCR. Your
fax will automatically call OpenLCR again when the rate data is
available. Until that time, long distance calls will be routed through
your primary carrier.
Your fax will automatically call OpenLCR within the next 24 hours to
learn when correct rate data will be available.
(Blinking)
Your fax did not receive the rate data because Open LCR was unable
to identify your Caller ID. This problem could be noise on the phone
line, or because your caller ID signal is blocked. Try retrieving the rate
data several more times. If "C" appears, you have retrieved the rate
data successfully. If you are still having problems, contact your phone
company and make sure they support Caller ID. You can remove the
"H" in your display by turning off the Open LCR function (press the
OpenLCR key followed by #, 1, 8, 4, and #). You can also register for
OpenLCR by phone to retrieve the rate data (see page 34).
37
2. Setting Up
OpenLCR
all.book
all.book
Page 38
Wednesday, February 13, 2002
10:00 AM
Setting Up and Using OpenLCR
Temporarily turning off OpenLCR
If needed, you can temporarily turn off OpenLCR.
♦ When you temporarily turn off OpenLCR, long distance and international
calls will not be routed by OpenLCR. However, your fax will still call
OpenLCR periodically to receive rate data.
Display:
Press
Press
once.
LCR DIAL
Press
once.
1=YES, 2=NO
Press 2 (NO) to turn off OpenLCR. (Press 1
OpenLCR back on.)
FUNCTION
once and
once.
LCR SETTING
(YES) to turn
• When you turn off OpenLCR, the highlighted “C” in the display will change
to “-”.
Press
STOP
to return to the date and time display.
To stop using OpenLCR
If you want to stop using the Open LCR feature, press this sequence of keys:
OpenLCR
1 ,
8 ,
4 ,
♦ Calls will not be routed by OpenLCR and the fax machine will not call
OpenLCR to update data.
To resume use of OpenLCR, press
38
OpenLCR
1 ,
8 ,
6 ,
all.book
Page 39
Wednesday, February 13, 2002
10:00 AM
Setting Up and Using OpenLCR
Changing your user profile
machine, and then press
OpenLCR
followed by
2. Setting Up
OpenLCR
If you need to change your user profile, pick up the handset on the fax
3 . Follow the instructions you
hear.
♦ If the display shows the alternating messages SET OWN NUMBER / 10
DIGITS, press the number keys to enter your fax/phone number, including
the area code (the number must be 10 digits long). When finished, press
START/MEMORY
♦ If you are on a pulse dial line, press
before pressing the number keys
to respond to the instructions. (This makes your fax temporarily issue tone
signals when you press the number keys.)
What to do if “E” appears in the display
A highlighted “E” will appear in the display in place of “C” if the rate data in the
fax is out-of-date and the fax is unable to obtain new data. When this
happens, OpenLCR routing will not take place.
TEL FAX
JAN-19 02:16
TAD
“E” indicates that the rate
data is out-of-date.
This will only occur if the fax machine is unable for some reason to make its
periodic call to OpenLCR to receive new rate data.
First try downloading the rate data manually by pressing
OpenLCR
and
as
explained in Downloading (receiving) the rate data manually on page 36. If
this doesn’t work, proceed to the following section, What to do if you cannot
connect to OpenLCR.
What to do if you cannot connect to OpenLCR
If you are unable to connect to OpenLCR when you use the OpenLCR key to
register or manually download data, it is likely that the phone number that the
fax machine dials when you press the OpenLCR key is no longer correct.
39
all.book
Page 40
Wednesday, February 13, 2002
10:00 AM
Setting Up and Using OpenLCR
To obtain the correct phone number, call OpenLCR at 970-206-1207, and
then program the number into the fax machine as explained below.
♦ Note: The number that you will obtain is the number for manually
downloading rate data (dialed by pressing the OpenLCR key and 2). When
you manually download the rate data, the new numbers for registering
(dialed by pressing the OpenLCR key and 1, 3, or 5) will also be
programmed in your fax machine.
Press
FUNCTION
once and
once.
Display:
LCR SETTING
Press
once and
Press
once.
Press
once.
CENTER # MODE
1=SET, 2=CLEAR
(SET) to set the new phone number.
• Note: If you wish to restore the factory-set number, press 2 for CLEAR
and then go to Step 6.
Press the number keys to enter the new phone number.
Press
Press
Press
START/MEMORY
STOP
OpenLCR
to store the number.
to return to the date and time display.
to download new rate data.
• If you have not yet registered with OpenLCR, your fax will receive new
phone numbers that will allow you to connect to OpenLCR. Register using
one of the procedures described at the beginning of this chapter.
40
all.book
Page 41
Wednesday, February 13, 2002
10:00 AM
Setting Up and Using OpenLCR
2. Setting Up
OpenLCR
Note: The following settings are not required as of the printing
of this manual. OpenLCR will inform you through its Web site
(www.OpenLCR.com) if the settings become necessary in the future.
Selecting a long or short call
Before you make a long distance or international phone/fax call, select
whether the call will be a long call or a short call.
♦ Your fax needs to know whether the call will be long or short to route it for
the best rate.
Press
OpenLCR
FUNCTION .
• Note: If the display shows TABLE NOT
Display:
LCR TABLE SELECT
EXIST, you must first download the rate
data.
Press 1 to select the SHORT TIME setting, or 2
TIME setting.
to select the LONG
• The initial SHORT TIME setting is 2 minutes, and the initial LONG TIME
setting is 4 minutes. If desired, you can change these settings as explained
on the following page.
• The short/long time selection will remain in effect for all calls until you
change it.
Changing the SHORT TIME and LONG TIME settings
The initial SHORT TIME setting is 2 minutes, and the initial LONG TIME
setting is 4 minutes. If the typical durations of your short and long calls are
different, you should change the time settings to ensure that OpenLCR routes
your calls for the best rate.
♦ For example, if your fax transmissions normally last about 3 minutes and
your phone calls last about 5 minutes, set 03 for the SHORT TIME and 05
for the LONG TIME. Before sending a fax, select the SHORT TIME setting
(03MIN) in the procedure on the preceding page. Before making a phone
call, select the LONG TIME setting (05MIN).
41
all.book
Page 42
Wednesday, February 13, 2002
10:00 AM
Setting Up and Using OpenLCR
♦ When you change the SHORT TIME and/or LONG TIME setting, the fax
machine will automatically call OpenLCR and receive rate data for the new
times.
Press
FUNCTION
once and
Display:
once.
LCR SETTING
Press
Press
Enter a 2-digit number (“01” to “ 29”)
for the number of minutes of the
SHORT TIME setting. (If the number is
less than 10, enter a 0 before the
number.)
once and
once.
LCR TIME
SHORT TIME
Enter a 2-digit number for the number
of minutes of the LONG TIME setting.
(The number must be greater than the
SHORT TIME setting and no more than
30.)
The display briefly shows
your selection, then:
LONG TIME
The display briefly shows
your selection. If the
settings were changed, it
will then show:
START: DOWNLOAD
• Note: If the display shows NO
SERVICE, you must first download the
rate data.
Press
START/MEMORY
to begin receiving the rate data for the new settings.
• Your fax calls OpenLCR and receives the data. This lasts one or two
minutes.
• Note: If you do not press
START/MEMORY
revert to their previous state.
42
to receive new data, the settings will
all.book
Page 43
Wednesday, February 13, 2002
10:00 AM
3. Using the Answering System
The answering system allows you to receive both voice messages and faxes
while you are out.
3. Answering
Machine
To use the answering system, you
will first need to record an outgoing
message. When you go out, turn on
the answering system by setting the
reception mode to TAD.
Recording an Outgoing Message
The outgoing message (OGM) is the greeting that the system plays after
answering a call to inform callers that they can leave a message or send a fax.
Follow the steps below to record a message.
Example:
“Hello. You've reached ______ . No one is available to take your call right now.
Please leave a message after the beep or press your facsimile Start key to
send a fax. Thank you for calling.”
Note: Do not lift the handset until Step 3 below.
Press
Press
Display:
REC/
MEMO
once and
once.
once.
OGM1(GENERAL)
LIFT HANDSET OR
• If you have already recorded a
message and wish to check it,
press
PLAY
PLAY: PLAYBACK
Lift the handset.
43
all.book
Page 44
Wednesday, February 13, 2002
10:00 AM
Operating the Answering System
Press
START/MEMORY
and speak into the handset to record a message.
• The outgoing message can be up to 60 seconds long. While recording, the
display will show the time left to record.
When finished, replace the handset or press
STOP
To listen to the outgoing message
To listen to the outgoing message, follow Steps 1 and 2 of the above
procedure and then press
PLAY
. Note that the general outgoing message
cannot be erased. If you need to change it, simply repeat the recording
procedure.
Operating the Answering System
Activating the answering system
To turn on the answering system so that callers can leave messages, press
RESOLUTION/
RECEPTION MODE
until the arrow in the display points to TAD. (TAD stands for
“Telephone Answering Device”.)
RESOLUTION/
RECEPTION MODE
TEL FAX
TAD
♦ The outgoing message will play (you can stop playback by pressing
STOP
).
♦ It will not be possible to set the reception mode to TAD if an outgoing
message has not been recorded.
44
all.book
Page 45
Wednesday, February 13, 2002
10:00 AM
Operating the Answering System
Note: In TAD mode, the machine will automatically switch to fax reception if it
detects six seconds of silence after answering a call. For this reason, if a
caller pauses for this length of time while leaving a message, they will be cut
off.
The number of rings on which the machine answers incoming calls in TAD
mode depends on whether the Toll Saver function is turned on, and if it is on,
whether you have messages.
♦ The Toll Saver function is initially turned on.
Toll Saver
No received messages
Hello!
Hi!
ing Ring R
g R
ing
Rin
OFF
Received messages
NOTHING
4 Rings
Toll Saver
ON
Hi!
2 Rings
Ring
To turn off the Toll Saver
function, see page 55.
Ring
(Answer according to
NUMBER OF RINGS setting)
ing Ring R
g R
ing
Rin
To adjust the NUMBER
OF RINGS setting, see
page 87.
45
3. Answering
Machine
Number of rings in TAD mode (Toll Saver function)
all.book
Page 46
Wednesday, February 13, 2002
10:00 AM
Operating the Answering System
Listening to received messages
When you return, the display will show the number of messages recorded.
Follow the steps below to listen to your messages.
Press
PLAY
• If you only want to listen to new messages (messages not previously
listened to), continue to hold
PLAY
down for at least two seconds.
The messages will play.
• As each message plays, the date and time of recording will appear briefly in
the display. If no messages were received, NO MESSAGES will appear.
• Repeat: To listen to a message a second time, press
before
REPEAT
playback of that message ends. To move back to the previous message,
press
within 3 seconds of the beginning of the current message.
REPEAT
• Skip: To skip forward to the next message, press
0 .
SKIP
Note: Playback will stop if you receive a call, lift the handset, or press
STOP
♦ You can print out a list of your received messages that shows the date and
time that each was received. See page 103.
46
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Modify Date : 2002:03:29 11:21:00+09:00 Create Date : 2002:03:29 11:20:13+09:00 Title : .橡.Table.PDF Author : .橡.IKEZAWA Creator : .橡.Microsoft Word Producer : Acrobat PDFWriter 4.05 Windows Page Count : 48 Mod Date : 2002:03:29 11:21:00+09:00 Creation Date : 2002:03:29 11:20:13+09:00 Metadata Date : 2002:03:29 11:21:00+09:00EXIF Metadata provided by EXIF.tools