Shen Zhen WFLY Technology Development WFT07 RADIO CONTROL SYSTEM User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1346004
Application ID	EuBdgD2Dpl/VlaLq2h52dg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	138.69kB (1733642 bits)
Date Submitted	2010-09-20 00:00:00
Date Available	2010-09-20 00:00:00
Creation Date	0000-00-00 00:00:00
Producing Software	Acrobat Distiller 7.0 (Windows)
Document Lastmod	0000-00-00 00:00:00
Document Title	Users Manual
Document Creator	PScript5.dll Version 5.2
Document Author:	Administrator

WFT07 2.4GHZ MULTI-LANGUAGE REMOTE CONTROL DEVICE
7 CHANNELS
INSTRUCTION MANUAL V1
Attention
▲ pls read the instruction before using the product
▲ Please keep this manual
ww w . wf lysz . com
WFT07 REMOTE CONTROL DEVICE
INSTRUCTION MANUAL
Thank you for purchasing the WFLY product
WFT07
Features
1.The large dot matrix LCD display: multi-language, graphical display. simple design, easy operation.
2.Original 2.4G technology
: use of data transfer, greatly improve the handling agility. fully express
the fast Lightning : (Note:
is WFLY exclusive technology).
3.Low-voltage design, lower battery consumption, a variety of battery available:such as 4S alkaline batteries ,
4S NiMH(Nickel Metal Hydride),1S lithium-ion battery ,1S lithium polymer battery . Voltage range 3.7V-6V.
4.Super anti-interference: the high spread spectrum (DSSS) + frequency hopping, can boot the 60 sets
at same time without interfere.
5.Optimization features into the design, operation .
Service
1.The WFLY warranty the quality of science and technology within a year (WFLY technology to bear the
postage, the user must provide a warranty card and proof of purchase,Indispensable).
2.Warranty card and proof of purchase effective by signed and sealed by the seller , and the information
must be completed.
3.Artificially damaged and over one year after the warranty period, the WFLY provide life long science
and technology service,only the users pay return postage, materials fees and maintenance costs.
4.This warranty is limited to China's remote control and accessories sales .
5.Seller does not give warranty card or do not fill out required from the seller to bear all the after-sales service.
WFT07 REMOTE CONTROL DEVICE
INSTRUCTION MANUAL
CONTENTS
10
WFT07 Remote control device contents
WFT07 Remote control device
WFT07 RC device parts of the name(front)
WFT07 RC device parts of the name( back)
Instructions of the 2.4Ghz receiver
WFT07 code match instructions
Trainer function
Special symbal instructions
WFT07 RC device characteristics
Express of input and buttons
Adjustment of stick head
Replacement throttle hand
Helicopter Functions
System Settings
Input mode and Functions
1.Model parameters
2.Model Settings
3. Coaching / Simulation
4.Control stick settings
5.Control stick Calibration
6. Restore factory settings
7.Tone settings
8.Contrast settings
9.Power supply scheme
10.Version information
11
13
13
13
14
14
15
15
15
16
16
Preferences
1.Monitor
2.Dual Rate
3.Servo Reverse
4.End point
5.Sub trim
6.Trim settings
7.Throttle curve settings
8.Pitch curve settings
9.Throttle cut settings
10.Throttle holding settings
11.Timer
12.Swashplate
13.Gyro sens mixing
14.Advanced settings
17
17
18
18
19
19
19
20
20
21
21
22
23
23
Ⅰ
WFT07 REMOTE CONTROL DEVICE
INSTRUCTION MANUAL
CONTENTS
Advanced settings
1.Speeder mixing
2.Fail safe
3.code match
24
24
25
Airplane Functions
system settings
26
27
27
27
27
27
27
27
27
27
27
Input mode and functions
1.Model parameters
2.Model settings
3. Coaching / Simulation
4.Control stick settings
5.Control stick calibration
6. Restore factory settings
7.Tone settings
8.Contrast settings
9.Power supply scheme
10.Version information
Preferences
27
27
27
27
27
27
27
28
28
28
29
29
29
29
29
1.Monitor
2.Dual Rate
3.Servo Reverse
4.End point
5.Sub trim
6.Trim settings
7.Flaperon mixing
8.Flap trim
9.Aileron diff control
10.Elev-flap
11.Throttle curve settings
12.Throttle cut settings
13.Throttle holding settings
14.Timer
15.Advanced settings
Advanced Settings
29
30
30
30
31
31
1.Elevator mixing
2.Ele-Aileron mixing
3.V-tail
5.Ail-2
6.Fail safe
7.Code match
Ⅱ
WFT07 REMOTE CONTROL DEVICE
INSTRUCTION MANUAL
WFT07 Remote control device contents
1.WFT07 remote control device 1 set
2. WFR07S 2.4G hz rece ive
3.Simulat or switch cable
1 Root
4.Transmitter 4cell battery case 1 A
5.Manual
1 This/zhang
6.WFLY neck strap
1 On ly
1 Ar ticle
WFT07 remote control device diagram
1.WFT 07 remot e control device
2.WFR0 7S 2.4Ghz receive
3.Si mul ator swi tch cable Man ual
WFT07 2.4GHZ MULTI-LANGUAGE REMOTE CONTROL DEVICE
7 CHANNELS
INSTRUCTION MANUAL V1
Att en tio n
▲ pls r ead t he in str uct ion b efo re us ing t he pr odu ct
▲ Ple ase k eep t his m anu al
4.Transmi tter 4cell battery case
www . wflysz . com
5.Man ual/ CD- ROM
6.WFLY neck strap
WFT07 REMOTE CONTROL DEVICE
INSTRUCTION MANUAL
WFT07 RC device parts of name
WFT07 RC device Positive
(Right hand throttle)
Antenna(rotatable)
Power light
RF light
Buzzer
K1
K2
V1
K3
K4
Throttle trim
Aileron/
throttle stick
Elevator trim
Rudder/
elevator stick
Power switch
Neckstrap
attachment
Rudder trim
Aileron trim
Left
Menu
Up
Right
Exit
Add
Down
Reduce
LCD
OK
K1: 2 stalls. Throttle holding and throttle cut
K2: 3 stalls. Timer , airplane 5channel and airplane Elev-flap mixing.
K3: 2 stalls. Dual rate, Fight mode (normal,special IDLE)
K4: Trainer. 7channels
WFT07 REMOTE CONTROL DEVICE
INSTRUCTION MANUAL
WFT07 RC device parts of name
WFT07 RC device back
Handle
Trainer/DSC
Battery cover
WFT07 REMOTE CONTROL DEVICE
INSTRUCTION MANUAL
Instruction of 2.4Ghz receiver
Model:WFR07S
Type: 7channel 2.4Ghz receiver,4096 resulotion(in the PCMS 4096 resolution)
(Adaptation WFLY 2.4Ghz series),ORGANIC 2.4G
Voltage :4.8V-6V
Current:30mA
Weight:9.6g
Size: 40.42mm x27.27mm x11.88mm
Frequency: 2.400GHz-2.483GHz
1．AIL：Aileron
(Channel 1)----------
2．ELE：Elevator
(Channel 2)----------
3．THR：Throttle
(Channel 3----------
4．RUD：Rudder
(Channel 4)----------
5．GRY： Landing Gear/Gyro (Channel 5)---------6．PIT： Pitch
(Channel 6)----------
7．Auxiliary channel
(Channel 7)----------
(Note: Any channel can be used as power input)
WFLY PCMS receiver cam compatible with PCMS 4096, PCMS 1024 and PPM modulation
(Adaptive), and have fail safe function.ORGANIC 2.4G
WFT07 REMOTE CONTROL DEVICE
INSTRUCTION MANUAL
WFT07 instructions of the code match
1.Remote control device settings
● unction instruction:
The remote control for the 2.4G spread spectrum,
frequency hopping systems, have high antiinterference. The remote control has unique
address identification code information, Before
use the remote control,pls match the code with the
2.4Ghz receiver.
● Settings
Into the "Advanced Settings" menu item under the
"Preferences" . Press confirm button to enter the
"code" interface in the "Advanced Settings" . As
above. The specific settings as follows: 1. The
first use the button to select on the code, the code
process needs within a short distance. 2.4G
module system in the closed state is not available,
please refer to “ Coaching / Simulation” Once Code
successfully will return to the menu. Also can press
"exit”button to return.
Warning
When using this function, please ensure that no other remote control operating!
2.Receiver Settings
Remote control device into this interface:
Then going receiver settings: receiver hold "SET" button until the STATUS indicator light flashes slowly, waiting for
the transmitter of the code instructions.
LED Slow flashing
(WFR07S/WFRO9S operating are same)
After the success of the code ,the LED light is off, you can normally using.
Note: The code required in a short distance.
WFT07 REMOTE CONTROL DEVICE
INSTRUCTION MANUAL
Trainer Function
Instruction of the Training function
The same two remote control devices WFT07 can do the Trainer function:
Settings:
1. Using the simulator cable to connect two WFLY equipment.
2. Trainer settings: Press MENU key to boot into the "System Settings" function, enter "
Training / simulation "menu,selected the" trainer mode ", (effect after re-boot ).
3. Student machine setting: Press MENU key of the another radio into the "System Settings" function,
entry "Training / simulation "menu,selected the " Simulator Mode ", (effect after re-boot ).
4. Release Trainer switch K4, this time the student machine does not sending signal, the operation
completed by the trainer.Advance push the trainer switch K4, then operation completed by the
Student machines now.
WFT07 REMOTE CONTROL DEVICE
INSTRUCTION MANUAL
Note the special symbol
For the safe use of this product, pls pay attention to
The marks have the following description of symbols.
Dangers: If you use in without a proper operation,it is possible to hurt user seriously injury or may even
cause death .
Warnings: If you use it without proper operation, it may make the user or others to hurt badly or may even
cause death,and it may cause slight hurt or damage to things
Warning: Children under 14 must be accompanied by an adult using
Notices: If you use it without a proper operation, it may cause user to hurt slightly or damage things,but
it won't hurt you seriourly normally.
Note: Turn on theTransmitter first, then turn on the receiver; after play pls turn off the Receiver first, then
the Transmitter
Flight Precautions
Prohibitions
Compulsory Items
Warning
※ Do not fly in the evening, rain,or strong wind.
Possible damage to equipment or aircraft accidents.
The Feature of WFT07 Remote control device
●
Large graphic dot matrix LCD display, easy to operate.
●
Multi-language
●
WFT07 RC device is the multi-function proportion of 7ch remote control .
●
The original 2.4G technology , with data transfer , which greatly improve the handling agility
Fully explain the fast as lightning. (Note: The
●
is the WFLY exclusive technology).
Low-voltage design, lower battery consumption, a variety of battery available:such as 4S alkaline batteries ,
4S NiMH(Nickel Metal Hydride),1S lithium-ion battery ,1S lithium polymer battery . Voltage range 3.7V-6V.
●
joystick of elastic, are free to adjust the hength of the head. The new shape of the head makes a good Feel.
●
Digital electronic tuning, 250 steps adjustable.
●
Complete the timer function to ensure flight foolproof
●
Monitor function can more intuitive operation.
●
Training function
●
Perfect timing function
●
Up to 11 groups of curves, easy to deal with difficult moving actions.
●
Multiple mixing control system , adjustable 9 point of the curve .
●
A variety of flight patterns,ease flight.
WFT07 REMOTE CONTROL DEVICE
INSTRUCTION MANUAL
Instruction of the input function
MENU:
After booting, press the menu button to enter the function menu - Preferences. In addition, if
the in the function interface, press this key will be Back to the menu.
EXIT:
Press this key, you can return to the previous menu level, or exit the edit state.
Add/Reduce Key:
Can be used to adjust values. Also set numerical value, press + / -, can accelerated settings the
functions.
Arrow Keys:
Arrow keys are divided into upper and lower, left and right keys, can be used to switch the set up
Or edit the item.
Confirm key:OK key ( this machine confirm key have three kinds of function )
※. With the menu to access the item.
※. To enter the edit mode.
※. Press this button long time, the selected item restore the default value
10
11
11
11
3 6
11
1.WFLY LOGO
2.2.4G RF circuit directed: shown 2.4G under work, closed wothout the logo.
3. Aircraft models: helicopter mode, shows the helicopter LOGO, airplane mode, shows the airplane LOGO.
4. Accumulative used time: to display the cumulative duration of the using, can also be reset clear.
5. Battery voltage display.
6. Model data file shows: 1,2,3 ... and so on.
7. Mixing status shows: mixing state (throttle holding, throttle cut, stunt mode) display MIX.
8. Helicopter swashplate shows: If you set a non-normal mode of swashplate, will show CCPM.
9. Trainer function display: Trainer mode will show "T",with flashing.
10. Timer display.
11. Digital electronic tuning: graphics + value dual display,and with tone reminder.
WFT07 REMOTE CONTROL DEVICE
INSTRUCTION MANUAL
Adjustment of stick head
Allen Key
Top thread
Stick Head
Put the stick head cover the control rod on
the left and right sides,don't twist down the
stick head to the bottom,and then put top
thread with allen key to adjust the height
you needed.
Stick
Twist the top thread down from
here,the height of the stick head
depends on the depth of the top
thread.
Adjust the height higher:First make the top
thread loose with the allen key,then twist
the stick head up,then make the top head
tighten with allen key.the stick head was
turned up.
Steps:
1.Put the stick head on the stick.
2.Put the top thread in the stick head with allen key.
3.Addjust top thread in the stick head with allen key to fix the height of the
stick head.
Adjust the height lower:First make the top
thread loose with the allen key,then twist
the stick head down,then make the top
head tighten with allen key.the stick head
was turned down.
WFT07 REMOTE CONTROL DEVICE
INSTRUCTION MANUAL
Replacement the throttle of mode 1 or 2
Right-hand man will lose their own free replacement warranty program
Bolt 3.
Bolt 2.
Bolt 1.
Bolt 4.
Set up release link and
springer,according your habit
to adjust the tightness of screw
2 to adjust the control felling.
Put on the matel
chip,according your habit to
adjust the elasticity of screw 3
and screw 4 to adjust the damp
of throttle control felling.
Take release link and spring
Down,and put it on the left side of the
location of corresponding,then twist
bolt1 down until withstand the adjust
nail ,in case adjust nsil will move away.
Take the metal chip and
screw down,and put it on
the similar position of the
right side.
10
Helicopter Functions
WFT07 REMOTE CONTROL DEVICE
INSTRUCTION MANUAL
Helicopter Functions
Introduction
This section are mainly introduces the helicopter functions. Please press the MENU button to turning on the
radio in turing off state, you can enter the "System setting” menu, Up / Down arrow keys to select" Model
Settings ", press the Enter key to enter the function setting interface, (as above). Please choose the model,
re-boot, then the transmitter can display the functions of the helicopter with the detailed description of each
function
Input mode and function introduction
1.The main interface
When the power turned on, the interface as shown. In this state, the user can view the machine voltage,
time display, model type and aileron, Throttle, elevator, rudder and so on trim state
Voltage
WFLY Logo RF modulation
Time display
Trainer function
display
Special mixing
Throttle trim
display
CCPM
Elevator
trim display
Timer
Rudder trim
display
Model parameters
display
11
Aileron trim
display
WFT07 REMOTE CONTROL DEVICE
Helicopter Functions
INSTRUCTION MANUAL
2 . Function Menu - There are “System settings”,”Preferences”and “Adcanced settings”
A. System Settings
In close state, hold down the MENU key, then turning on the power, you can enter the "System Settings"
menu page, the interface as shown.
In this state, all functions can be set one by one. As follows:
1. Use the arrow keys on the screen to select the functions you needed, use up and down keys to select
function items. With the left and right arrow keys to flip.
2. In the functional state ,press OK key to enter sub-menu of the function. The function of specific
configuration, please refer the next chapter.
3. When Settings finished, press EXIT key to return to superior menu,it will automatically store the Settings
value.
B. Parameter Settings
In the boot screen, press the MENU button on the left screen, you can enter the "settings" menu page, the
interface as shown.
In this state, the machine can be set one by one the various functions. As follows:
1. Use the arrow keys on the screen to select the functions you needed, use up and down arrow keys to
select function items. With the left and right arrow keys to flip.
2. In the functional state ,press OK key to enter sub-menu of the function. The function of specific
configuration, please refer the next chapter.
3.When Settings finished, press EXIT key to return to superior menu,it will automatically store settings
Value.
C. Advanced Settings
Into the "Preferences" menu, use the left and right arrow keys to flip, can see the "Advanced Settings"
function key. Click OK key to enter.
In this state, the machine can be set one by one the various functions. As follows:
1. Use the arrow keys on the screen to select the functions you needed, use up and down arrow keys to
select function items. With the left and right arrow keys to flip.
2. In the functional state , press OK key to enter sub-menu of the function. The function of specific
configuration, please refer the next chapter.
3.When Settings finished, press EXIT key to return to superior menu, it will automatically store settings
Value.
12
WFT07 REMOTE CONTROL DEVICE
Helicopter Functions
INSTRUCTION MANUAL
System Settings Menu Introduction
1.Model Parameters
●Function
Model parameters function totally have three
machines for the user to choose, you can select
any of them model to settings.
●Settings
Press the MENU button to boot into the “System
Settings" menu, use Up / Down keys to
select the "model parameter settings", and
press the “OK ” key into the function interface,
as shown above.
The steps of setting is as follows:
1. Using the up / down keys to select different
models.
2. Selected the options, press OK key to select .
3. Settings successfully, press EXIT key to exit.
2.Model Settings
●Function
Model settings can be used to set to the
helicopters, airplane as you needed.
●Settings
Press the MENU button to boot into the "System
Settings" menu, use Up / Down keys to select
"Model Settings", press the OK key into this
function interface, as shown above.
The steps of setting is as follows:
1. Up / Down keys to select the model.
2. Click OK key to confirm.
3. Settings finished, press EXIT key to return to
3.Coaching / Simulation
●Function
◆Normal: normally use the model, RF 2.4GHz
work, do not support the trainer.
◆Trainer mode: use the unit as a trainer, use the
training cable connect the other one as a student
machine. through the unit RF 2.4G machine
control,with the K4 switch. Not switch K4 is
sending the trainer machine signal, when push
the switch K4 is sending the student machine
signal.
◆Simulator Mode: This mode will turn off RF 2.4G
in order to facilitate learning with other remote
control. Or connect with the computer to simulate
the flight to reduce power consumption to increase
the use of time.
Note: For security, the above mode switch to take e
ffect after reboot.
13
WFT07 REMOTE CONTROL DEVICE
Helicopter Functions
INSTRUCTION MANUAL
●Settings
Press the MENU key to boot into the "System
Settings" menu,use Up / Down arrow keys to
select the "trainer / Simulator", press OK key to
enter the function interfacet, as shown above.
The steps of setting is as follows:
1, first to use the up / down arrow keys to edit the
selected item.
2. Press OK button to confirm, then press the right
arrow keys to determine. Reboot to take effect.
4.Control Stick Settings
1---ileron
2---evator
3---hrottle
4---Rudder
●Function
Control stick settings function allows users
to freely setting the higher of the stick according
to personal preferences . As shown. This machine
Totally have four models to choose .
●Settings
Press the MENU key to boot into the "System
Settings" menu,use Up / Down keys
to select the "stick settings" and press OK key to
enter this function interface, as shown above
The steps of settings is as follows:
1. First to use the arrow keys to select the edited
item .
2 Use Up / Down key to implementation Stick Mode .
3. Set successfully, press EXIT key to exit.
5. Stick Calibration
●Function
Joystick calibration function allows users to
change the throttle side according to personal
preferences .
图3
●Settings
Press the MENU key to boot into the "System
Settings" menu,use Up / Down keys to select
"Stick calibration" and press OK key to enter the
function interface, as Shown above. Specific
settings, follow these steps: 1.First to use the arrow
keys to select the edited item, (example aileron
calibration). 2.Put the calibrate joystick placed in the
midpoint of the channel position, options Up / Down key implementation the control calibration . 3.Selection
into the Figure 3. When the "middle" highlighted, press
OK key (this time the Point calibrated is OK), into the
stickmaximum (high) calibration. 4.When the "high"
highlighted, put the stick gently leaned on the right
(throttle /elevator on the top edge, aileron / rudder on the
right edge), press the OK key (in this case the maximum
value has been calibrated), into the stick minimum (low)
calibration. 5.When the "low" highlighted, put the stick
gently leaned on the left (throttle / elevator on the lowest,
Aileron / rudder on the left edge), press the OK key (while
the stick minimum calibrated OK). 6.At this memont the
bottom of the screen displays "confirmation / reset" and
press to OK key ,all the calibration is completed,
automatically return to the superior menu, use the
arrow keys selected to re-enter Calibration
Procedures.
14
WFT07 REMOTE CONTROL DEVICE
Helicopter Functions
INSTRUCTION MANUAL
6.Restore factory settings
●Function
Reset function is to present the model all the
data back to the initial default settings, so can do
Comprehensive settings of re-work.
Procedures.
●Settings
Press the MENU key to boot into the "System
Settings" menu, use Up / Down keys to select
"reset ", press Confirm key into the function
interface.As above:
The steps of settings is as follows:
1. First to use the arrow keys to select the
Edited item.
2. With + / - key to implementation the reset.
3. Set successfully, press EXIT key to return.
7.Tone Settings
●Function
Tone settings allows users to freely set all the
sounds on or off according to personal
Preference.
●Settings
Press the MENU key to boot into the "System
Settings" menu, use Up / Down keys to select
"Sound", press the OK key to enter the function
interface, as above.
The steps of settings is as follows:
1. Into the items, press OK key to select the sound
on or off.
2. Automatically saved after confirmation.
8.Contrast Settings
●Function
The contrast setting function can
adjust the brightness of the display ,
increase or decrease the contrast value to
change the brightness of the screen.
●Settings
Press the MENU key to boot into the
"System Settings" menu,use Up / Down
keys to select "Contrast settings" and
press OK key to enter the function
interface ,as above.
The steps of settings is as follows:
1. Using the + / - keys to set the value of
increase / decrease.
2.Long time press OK key restore the default
value.
3. Set successfully, press EXIT key to return.
15
WFT07 REMOTE CONTROL DEVICE
Helicopter Functions
INSTRUCTION MANUAL
9.Power supply scheme
●Function
The machine can use a variety of power options:
If ordinary alkaline AA batteries 4S, Ni-MH / Ni-Cd
battery 4S, Li-Ion / Li-polymer battery 1S.
Different battery in different low-battery voltage
alarm, in order to extend battery life, select the
corresponding power supply plan.
Note:Voltage range 3.7V-6V.
●Settings
Press the MENU key to boot into the "System
Settings" menu,use Up / Down arrow keys to
select "Power Information", press OK button to
enter the function interface. As shown above. The
steps of setting is as follows:
1. The first to use the arrow keys to edit the selected
item.
2. Select the power scheme with the + / - key to
implementation.
3. Set successfully, press EXIT key to exit.
10.Power supply scheme
16
WFT07 REMOTE CONTROL DEVICE
Helicopter Functions
INSTRUCTION MANUAL
Introduction of the Parameters Settings Menu
1.Monitor
CH 1
CH 6
CH 2
CH 7
CH 3
CH 4
CH 5
●Function
The monitor function is to monitor and confirm the
channel operation state.
●Settings
In the "Preferences" interface, use Up / down keys
to select the "Monitor", press OK key to enter the
function interface, as above.Then can monitor
each channel action condition
2.Dual Rate Settings
Cur ve poi nt and Cur so r line
Sel ec t ac tion
(Ai ler on, El ev at or,Rudder )
Sw itch K3
End poi nt
Cur ve
Expon ent ial
Cur ve poi nt di sp lay
●Function
Dual Rate function is by setting the switch to
change the aileron, elevator, and rudder of the
control rate.
●Settings
In the "Preferences" interface, use Up / down keys
to select the "Dual rate ", press OK key to enter
the function interface . As above.
The steps of settings is as follows
1. Select the required channel (eg, aileron,
elevator etc.). Use the + / - key to select the
required channel, confirmed with OK key.
2. Select the K3 switch position (position 0 or
position 2). Use the + / - button to select the
required location .
3. Settings the D / R, Use the arrow keys to select
the the "D / R 'in screen, when the screen light off,
then enter the edit mode of this function.
(You can choose settings single parameter or two
parameters at the same time ), then press + / - keys
to change the values ,long press OK key can be
recovered to the default value.
17
WFT07 REMOTE CONTROL DEVICE
Helicopter Functions
INSTRUCTION MANUAL
4. Settings exponential EX, can change the
aileron, throttle and rudder these three channels'
joystick sensitivity near the neutral. Dual rate and
curve exponential are match, will have a lot of
combinations and settings, with the arrow keys to
select the "EX" in the screen, settings way are same
as "D / R" .
5. Use the arrow keys to select the curve point, + /
- key to changing the value of curves point.
6. Set successfully, you can press EXIT key to
return.
3.Servo Reverse
●Function
Servo reverse function can adjust the direction of
the servo moves to make the direction of servo
movement is normal or reversed.
●Settings
In the "Preferences" interface,use Up / Down keys
to choose "Servo reverse", press OK key to
confirm enter the function interface.As above.The
steps of settings is as follows:
1. First to use the arrow keys to select the edited
item.
2. with + / - keys to switch the action is normal or
reverse and use the OK keys to implement.
3. Set successfully, press EXIT key to return.
4.End Point
●Function
End point function can determine the end point of
the servo's initial value, adjusting the largest
route of servo movements, the adjustment range is
between 0% -120%.
●Settings
In the "Preferences" interface,use up / down keys
to select the "End point" and press OK key to enter
the function interface, as above. The steps of
1.First use the arrow
settings is as follows :
keys to select the edited items.
2.Set the value of the route with + / - key. Long press
OK key to restore the default values.
3. Set successfully, press EXIT key to return.
18
WFT07 REMOTE CONTROL DEVICE
Helicopter Functions
INSTRUCTION MANUAL
5.Sub Trim
●Function
When the electronic trim can not make the servo
to achieve a satisfactory angle, be corrected by
the function, can make the servo to reached a
ideal angle which user wanted. When set this
function , please place the trim in the central
location, then start setting
●Settings
In the "Preferences" interface,use Up / Down keys
to select the "Sub trim", press the OK key to
confirm you access in this interface, as above.
The steps of settings is as follows:
1. First to use the arrow keys to select the edited
item.
2. Set the amount of the sub trim of movement with
the + / - keys or used the OK key to implement, long
press the OK kay can restore the default value.
3. Set successfully, press EXIT key to return.
6.Trim Settings
●Function
Trim settings function is adjustment for each trim
to change the trim sensitivity, settings amount can
be 1-250.
●Settings
In the "Preferences" interface, use Up / Down
keys to select the "Trim" and press OK key to
confirm access in this function interface, as
above The steps of settings is as follows:
1. First to use the arrow keys to select the Edited
item.
2. Set the amount of Trim with the + / - key,use OK
key to implement. If "reset", can set the trim location
value to zero.
3. Set successfully, press EXIT key to return.
7.Throttle Curve Settings
Flight Mode
Dual rate
Exponentia
Curve picture
Curve point
●Function
Throttle curve with the throttle stick position to
adjusted the engine flight in the best state. This
throttle curve can set to normal and stunt curves
and so on.The operation of those curves can
carried out by the switch.The throttle curve of
normal curve is basic on hovering, the engine rpm
with the pitch can achieve the best effect. Stunt
Curve is maintaining a certain engine speed,make
the throttle with the pitch to complete the stunts in
the flying .
19
WFT07 REMOTE CONTROL DEVICE
Helicopter Functions
INSTRUCTION MANUAL
●Settings
In the "Preferences" interface,use Up / Down keys
to select the "throttle curve settings", press OK
key to confirm enter the function interface, as
above.
The steps of settings is as follows:
1. Flight status (normal or stunt). Use the arrow
keys to enter edit state, you use + / - keys to select
one of the curve, then enter the following settings.
2. Set the D / R, Use the arrow keys to select the
"D / R"in the screen, when the screen light off,
then enter the edit state of this function(you can
choose individual settings on one or setting on both
sides ), Press the + / - keys to set the values,long
press the OK key to return to the default value.
3. Use left and right arrow keys to select curve
points, + / - keys to change the value of curve points.
4. Set successful, you can press EXIT key to return.
8.Pitch Curve Settings
Flight Mode
Dual rate
Exponentia
Curve picture
Curve point
●Function
Pitch curve with the throttle stick position can
adjusted the engine rpm flight in the best state,
This pitch curve can be set normal, stunt and lock
curve and so on. The operation of those curve can
carried out by the switch.Pitch curve of normal
curve is based on hovering, as a certain engine rpm
to adjust the pitch to the best place . Stunt pitch
curve is maintaining a certain engine rpm, make the
pitch with the throttle to complete stunts in flying.
●Settings
Pitch curve with the throttle stick position can
adjusted the engine rpm flight in the best state,
This pitch curve can be set normal, stunt and lock
curve and so on. The operation of those curve can
carried out by the switch.Pitch curve of normal
curve is based on hovering, as a certain engine rpm
to adjust the pitch to the best place . Stunt pitch
curve is maintaining a certain engine rpm, make the
pitch with the throttle to complete stunts in flying.
9.Throttle Cut Settings
●Function
Throttle cut settings function is to make the
engine off when the flight finished. Switch K1 is for
opening and closing the throttle. Throttle trim
adjustment will affect the throttle closed position
when implement the action. So when moving the
throttle trim,have to check the throttle closed action
position .
Warning:
Settings and Notes:When the throttle closed
switch move to open, can adjust the value until the
carburetor valve fully closed (engine shutdown).
To prevent the error in the adjustment operation,
the throttle turn off the function of the best range of
motion is to set near the engine speed .
●Settings
In the "Preferences" interface,use Up / Down keys
to select the "throttle cut settings", press OK key
to confirm enter the function interface, as above.
The steps of settings is as follows:
1, the first to use the arrow keys to select Edit
Item2. Throttle cut settings function on or off with
a + / - key to implement.3.Under the throttle cut
condition, the rate of value and trim amount can
settings with + / - key to the implement (adjustable
range of ± 45%).4. Set successfully, press EXIT key
to return.
20
WFT07 REMOTE CONTROL DEVICE
Helicopter Functions
INSTRUCTION MANUAL
10.Throttle holding Settings
●Function
Throttle holding settings can set in when throttle
cut landing , fixed the throttle servo in the a low
speed position , throttle holding position can be
adjustment within ± 75% .
Switch K1 work for this function.
●Settings
In the "Preferences" interface,use Up / Down keys
to select the "throttle holding settings", press OK
key to confirm enter the function interface, as
above. The steps of settings is as follows:1, the
first to use the arrow keys to select Edited Item.2.
. In the "mixing" item to set on or off this mixing
function , with + / - keys to implement.. 3. In the
"Location" item to set the throttle holding location,
with a + / - key to implement. Long press OK key to
restore the default values. 4. Set successfully, press
EXIT key to return.
11.Timer
●Function
As the different of each Helicopter fuel tank size
and engine speed, will lead to vary different flight
time.The Timer function can alert you in warning
tone landed the plane safely on the ground before
you used up the fuel .
◆The maximum time of the timer is 99 minutes
and 59 seconds. In the work every 1 minute to tips
time, from 20 seconds to the time, each second
alert with short-ring ,when from 10 seconds to the
time,each second alert with long-ring, regular
arrival will blew tips.
◆ can set the timing and countdown.
◆ Control way : K2 switch control, throttle control,
automaticel work after boot.
●Settings
In the "Preferences" interface,use Up / Down
keys to select the "Timer", press OK key to
confirm enter the function interface, as above.
The steps of settings is as follows:
1, First to use the arrow keys to select Edited
Item.
2. In the "Timer" item set the timer.
3. In the "minutes ..seconds .. " option to set the
time, with a + / - key to implement. Long press OK
key to restore the default value.
4. In the "mode" item set mode. With a + / - key to
implement.
5. In the "Control"item set the control switch, with + /
- key to implement.
6. In the "position" item set the throttle control
location. With a + / - key to implement.
7. Set successfully, press EXIT key to return.
21
WFT07 REMOTE CONTROL DEVICE
Helicopter Functions
INSTRUCTION MANUAL
12.Swash
Swash type selection
●Function
If using a helicopter with CCPM, connecting a
cross-shaped piece of servo will automatic going
the mixing action. Please use the helicopter
swash according to the type of choice. This
remote control device offers two modes: normal,
and 3CH120 (CCPM) mode. As above
●Settings
In the "Preferences" interface,use Up / Down keys
to select the "Swash", press OK key to confirm
enter the “Swash type selection “interface, as
above.
The steps of settings is as follows:
1. First to use the arrow keys to select the Swash,
press OK key to enter.
2. Selected swash type selection press OK key to
enter, with + / - key to implement the selection mode.
3.. Set successfully, press EXIT key to return.
Swash Parameter adjustment
●Function
Swash parameter adjustment function is selected
the swash type for adaptation the aileron elevator,
pitch three parts .
●Settings
In the "Preferences" interface,use Up / Down keys
to select the "Swash", press OK key to confirm
enter the “Swash type Adjustment“interface, as
above.
The steps of settings is as follows:1. First to use
the arrow keys to select the Swash, press OK key
to enter.
2. Selected the swash parameter adjustion press
OK key to enter, with Up/down key to implement the
selection.use +/ -- Key to adjust the parameters.
3.. Set successfully, press EXIT key to return.
22
WFT07 REMOTE CONTROL DEVICE
Helicopter Functions
INSTRUCTION MANUAL
13.Gyro Sens Mixing
●Function
Can adjust the gyro sensitivity directly from the
transmitter, you can choose AVCS gyro (GY) and
ordinary gyro (STD). Gyroscope sensitivity switch
plugs into the 5 channel of the receiver. This time
5channel in front of the auxiliary channel setting is
temporarily non-functional,switch sensitivity by
flight mode (Normal stunt lock) .
●Settings
Into the "Preferences" under the”Advanced
Settings” menu,use Up / Down keys to select the"
gyro sens mixing "function , press the OK key to
enter the function interface. As above. Specific
settings steps are as follows:1. First to use arrow
keys to enter the edit mode.
2. In the "mode" option set flight mode, With a + / key to implement.
3. In the "mixing" options settings on or off this
function, use + / - key to implement. Long press OK
key to restore default.
4. In the "position" option to set the control position
on or off this function, with a + / - key to implement.
5. In the "ratio" option set the mixing value, with + / key to implement. Long press OK key to restore the
default value.
4. Set successfully, press EXIT key to return.
14.Advanced Settings
●Function
This machine for allowing users to achieve more
satisfactory flight effect, added some special
features in the "Advanced Settings" function.
Interface as shown. The purpose of each function
will be introduced in the following
●Settings
In the "Preferences"interface,use Up / Down
keys to select "Advanced Settings" and press OK
key to enter the function interface, as above.
In this state, press left and right arrow keys can
turn the pages, press the + / - keys to select the
function item. The specific function and setting
method. Please refer below.
23
WFT07 REMOTE CONTROL DEVICE
Helicopter Functions
INSTRUCTION MANUAL
Introduction of Advanced Setting Menu
1.Speeder Mixing Settings
●Function
Speeder mixing settings is under the case have
the speeder, uses and settings the speeder . In the
state can set the output action servo.
●Settings
Into the "Preferences" under the Advanced
Settings "menu.use Up / Down keys to select the"
Speeder mixing settings ", press the OK key to
confirm enter the interface. The steps of settings
is as follows:
1. First to use the arrow keys to enter the edit
mode.
2. In the "mixing" option to set the on/off of the
mixing functions, with + / - key to implement.
3. In the "ratio" option set the mixing value, with + / key to implement. Long press OK key to restore the
default value.
4. Set successfully, press EXIT key to return.
2.Fail Safe
●Function
Fail safe function is used for various reasons
(such as interference,long distance), the receiver
will lost the transmitter signal,and the receiver will
automatically return to the default values position or
maintain the current value of the function.
●Settings
Press the MENU key to boot into the
"Preferences" menu, use Up / Down keys to
choose "Fail safe" and press OK key to enter the
function interface, as above . Can not use this
feature when the 2.4 G module in close state.
The steps of settings is as follows:
1.First to use the arrow keys to select the edited
item .
2. With a + / - key to maintain the settings / specific
position.
3. Click OK key, can be deposited the current actual
channel parameters.
4. Set successfully, press EXIT key to return.
Warning :
When using this feature, please ensure that no
operation of other remote control!
24
WFT07 REMOTE CONTROL DEVICE
Helicopter Functions
INSTRUCTION MANUAL
3.Code Match
●Function
This remote control are the 2.4G spread
spectrum, frequency hopping systems, with a high
anti-interference. Each remote control only has an
identification code information, before you use the
remote control system pls matched with the 2.4G
receiver which including in this device.
●Settings
Into the "Preferences" under "Advanced settings"
menu. Press OK key to enter the “Code “interface
under the "Advanced Settings" . As above.
Specific settings following these steps:
1. First to use the arrow keys to select the” code”,
the process of the code needed within a short
distance. 2.4G module system in the closed state is
not available, please refer to "modulation type."
Once the code successfully will initiative to return to
the menu. also can press "exit” Key to Quit.
Warning
When using this feature, please ensure that no
operation of other remote control!
25
Airplane Function
WFT07 REMOTE CONTROL DEVICE
INSTRUCTION MANUAL
Airplane Function
Introduction
This section are mainly introduces the airplane
functions. Please press the MENU key to boot,
you can enter the "System settings”item,use Up /
Down keys to select" Model Settings ", press the
OK key to enter the function interface, (as
Shown). Please choose the model, re-boot, the
transmitter can display the functions of airplane.
Following description the details of each function.
Input mode and Functions
1.The main interface
When the power switch turned ON, the interface
as shown. In this state, the user can view the
Voltage
Voltage, Time, Models and Aileron, Throttle,
Elevator, Rudder and other state
WFLY Logo RF modulation
Time display
Trainer function
display
Special mixing
Throttle trim
display
Elevator
trim display
Timer
Rudder trim
display
2.Function Menu
Model parameters
display
Aileron trim
display
Selection refer the instructions on page 12
26
WFT07 REMOTE CONTROL DEVICE
Airplane Function
INSTRUCTION MANUAL
Introduction of System Settings Menu
1.Model parameters
Selection Refer the instroduction on page
13
2.Model Setting
Selection Refer the instroduction on page
13
3. Coaching / Simulation
Selection Refer the instroduction on page
13
4.Stick settings
Selection Refer the instroduction on page
14
5.Stick calibration
Selection Refer the instroduction on page
14
6. Restore factory settings
Selection Refer the instroduction on page
15
7.Tone settings
Selection Refer the instroduction on page
15
8.Contrast settings
Selection Refer the instroduction on page
15
9.Power supply scheme
Selection Refer the instroduction on page
16
10.Version Information
Selection Refer the instroduction on page
16
Introduction of Parameter Settings Menu
1 Monitor
Selection Refer the instroduction on page
17
2 Dual rate
Selection Refer the instroduction on page
17
3 Servo reverse
Selection Refer the instroduction on page
18
4 End point
Selection Refer the instroduction on page
18
5 Sub trim
Selection Refer the instroduction on page
19
6 Trim
7.Flaperon mixing
Selection Refer the instroduction on page
19
●Function
This feature is to use two mixers in the aileron, to
make aileron have a mixer like flap function.
●Settings
Press the power button to boot into the
"Preferences" menu,use Up / Down arrow to
select the "Flaperon mixing", press OK key to
enter the function interface, as above.
The steps of settings is as follows:1. Using the up
/ down keys can choose to the edit item.
2. Selected the options, press the + / - key to edit the
data. Long press OK key to restore the default
values.
3. Set successfully, press EXIT key to retrun.
27
WFT07 REMOTE CONTROL DEVICE
Airplane Function
INSTRUCTION MANUAL
8 Flap trim
●Function
This feature is for 6 channels to do the trim stick
action.
●Settings
Press the power key to boot into the "parameter
settings" menu, use Up / Down keys to select the
"Flap trim", press OK key to enter the function
interface, as above. The steps of settings is as
follows:
1. Using the up / down keys can choose to the edit
item.
2. Selected the options, press the + / - key to edit the
data. Long press OK key to restore the default
values.
3. Set successfully, press EXIT key to return.
9 Aileron diff control
●Function
This feature is used in have two aileron servo, you
can create the differential aileron movement.
●Settings
Press the power button to boot into the "parameter
settings" menu,use Up / Down keys to select the
"Aileron diff control", press OK key to enter the
function interface, as above. The step of settings
is as follows:
1. Use the up / down key to select the Edit Item
2. Selected the options, press the + / - key to edit the
data. Long press OK kry to restore the default value.
3. Set successfully, press EXIT key to return.
10 Ele-Flap Mixing
●Function
This feature is to make the flap, elevator doing the
corresponding action. Flap down, elevator up,
make the stunt movement more fluid . K2 controls
the switch.
●Settings
Press the power button to boot into the
"Parameter setting" menu, use Up / Down keys to
select the "Ele-flap mixing", press OK key to enter
the function interface. As above.
The step of settings is as follows:
1. Using the up / down keys to choose the edit item.
2. Selected the options, press the + / - key to edit the
data. Long press OK key to restore the default
values.
4. Set successfully, press EXIT key to return.
28
WFT07 REMOTE CONTROL DEVICE
Airplane Function
INSTRUCTION MANUAL
11 Throttle Curve Settings
Selection Refer the instroduction on page
19
12 Throttle Cut Settings
Selection Refer the instroduction on page
20
13 Throttle Holding Settings
Selection Refer the instroduction on page
21
14 Timer
Selection Refer the instroduction on page
21
Advanced Settings Menu
1 . Elevator Mixing
●Function
This feature is generally applicable to the Elevon
mixed by aileron and elevator , Can adjust the
aileron, elevator action volume independently.
Notes:
The three of Elevon, V tail, elevator function can
not be open simultaneously. Also Ele --Aileron,
flaps, aileron diff is also only can use one function,
can not be open when the other functions working,
this feature will show " warning "Please forbid the
other mixing, and then turn on this feature. As
shown on the right
●Settings
Into the "Preference Settings" under "Advanced
Settings" menu , use up / down keys to select the
"Elevator mixing", press OK key to enter the
function interface, as above.
The step of settings is as follows:
1. Using the up / down keys to choose the edit item.
2. Selected the options, press the + / - key to edit the
data. Long press OK key to restore the default
values.
2. Set successfully, press EXIT to return.
29
WFT07 REMOTE CONTROL DEVICE
Airplane Function
INSTRUCTION MANUAL
2.Ele-Aileron Mixing
●Function
This feature is to allow elevator to work in the
aileron mixing function.
Notes:
Ele--aileron mixing, V-tail , Ele- flaps can not be
opened simultaneously, if the screen displays
"warning", please forbid the other mixing functions,
then turn on this function.
●Settings
Into the "Preferences settings" under "Advanced
Settings" menu .use Up / Down keys to select "Ele
- aileron mixing", press OK key to enter the
function interface . As above.
The steo of settings is as follows:
1. Using the up / down keys to choose the edit
item.
2. Selected the options, press the + / - key to edit the
data. Long press OK key to restore the default
values.
4. Set successfully, press EXIT key to return.
3.V-Tail Mixing
●Function
This feature is use for V-tail aircraft the elevator
and rudder mixing function.
●Settings
Into the "Preferences Settings" under "Advanced
Settings" menu.use Up / Down keys to select "Vtail mixing" and press OK key to enter the function
interface. As above.
The step of settings is as follows:1. Using the up /
down keys to choose the edit item.
2. Selected the options, press the + / - key to edit the
data. Long press OK key to restore the default
values.
3. Set successfully, press EXIT key to return.
30
WFT07 REMOTE CONTROL DEVICE
Airplane Function
INSTRUCTION MANUAL
4.Aileron-2
●Function
Aileron -2 is aileron another channel 's
distribution.
●Settings
Press the MENU key to boot into the "System
Settings" menu, use Up / Down keys to select the
"aileron -2", press the OK key to enter this function
interface, as above.
5 Fail Safe
The step of settings is as follows
1. Using the + / - keys to choose different models.
2. Selected the options, press OK key to confirm.
3. Set successfully, press EXIT key to return.
Selection Refer the instroduction on page
24
6 Code Match
●Function
This remote control is the 2.4G spread spectrum,
frequency hopping systems, with a high antiinterference. Each remote control has unique
identification code information, before you use the
remote control system pls matched with the 2.4G
receiver including in the device.
●Settings
Into the "Preference Settings" under "code" menu
. Click OK key to enter the state of the coding. As
above
The step of settings is as follows:
1. First to use the arrow keys to select on the
code, the process of the code needed within a
short distance. 2.4G module system can not use this
function in the closed state, please refer to
“ Coaching / Simulation " Once the code successfully
will initiative to return the menu. Also Can press
"Exit"key to quit.
Warning :
When using this function, please ensure that no
other operation of remote control!
FCC WARNNING
Changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment..
31
SHENZHEN WFLY TECHNOLOGY DEVELOPMENT CO.,LTD
Room 618-619,6/F Chuangye Building, No.1 Qilin Road, Nanshan District, Shenzhen 518052, P.R.China
Tel：+0755-26581815 Fax：+86-755--26585126 http:// www.wflysz.com
Email：sale2@wflysz.com
Thank you for purchasing WFT07 remote control device, pls read the instructions carefully before use it.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : 3.1-701
Creation Date--Text             : 
Mod Date--Text                  : 
Producer                        : Acrobat Distiller 7.0 (Windows)
Create Date                     : 2010:09:13 16:37:52+08:00
Modify Date                     : 2010:09:13 16:37:52+08:00
Metadata Date                   : 2010:09:13 16:37:49+08:00
Creator Tool                    : PScript5.dll Version 5.2
Document ID                     : uuid:9939273112BFDF119D45B9D8A10B160A
Instance ID                     : uuid:32fc57a6-ecb8-410c-a872-91d409eb2a43
Derived From Instance ID        : uuid:6a5424d9-bc90-4d06-be3b-f6f9afe30b81
Derived From Document ID        : uuid:694CAFD5FBBBDF11BB4CCEABD229608C
Format                          : application/postscript
Title                           : WFT07閼昏鲸鏋冪拠瀛樻娑?cdr
Creator                         : Administrator
Page Count                      : 36
Author                          : Administrator

EXIF Metadata provided by EXIF.tools