Shen Zhen WFLY Technology Development WFT09II RADIO CONTROL SYSTEM User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1536776
Application ID	pG0ZVWljXHvDeBgOZxWi6g==
Document Description	USERS MANUAL 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	318.69kB (3983572 bits)
Date Submitted	2011-09-06 00:00:00
Date Available	2011-09-06 00:00:00
Creation Date	2011-09-06 15:46:53
Producing Software	Acrobat Distiller 7.0.5 (Windows)
Document Lastmod	2011-09-06 15:46:58
Document Title	Users Manual
Document Creator	PScript5.dll Version 5.2
Document Author:	Administrator

HELICOPTER
INSTRUCTION
Language
This function is to select the language. The selection is
as shown in the picture , if only English or Chinese menu ,
the function is not exist .
36
HELICOPTER
INSTRUCTION
NORMAL SETTING(helicopter)
1. MONITOR
Monitor shows the servos’ movement situation.
In PCMS, this function is to describe the 9 channels output.
In PPM, this function is to describe the first 8 channels output.
Setting Method:
Press menu button, enter system setting, the first function is
the monitor.
37
HELICOPTER
INSTRUCTION
2. DUAL RATE & EXPONENTIAL SETTING
(1). AIL
Servo
Switch
Curve picture
(please refer to Page 27)
Dual rate
Exponential
Curve point
(3). RUD
(2). ELE
Dual rate is to adjust aileron, elevator and rudder travel range.
The range is between 0%-120%.
Exponential setting is to adjust aileron, elevator and rudder
sensitivity when the sticks are around the middle. The range is
between -100% to +100%.
Setting Method:
1. Select channel
Aileron, elevator and rudder are selectable. Press +/- buttons
to select channel, OK button to finish setting.
2. Set the switch and its position(0,1,2)
Press direction button to select “SWT”, edit it. +/- buttons can
select function switch(A-F).
After selecting the function switch, press right direction button
to enter the switch position setting, use +/- buttons to set.
3. Set dual rate
Press direction button to select “D/R”, edit it. Edit one or two
parameter.
+/- buttons can increase or decrease the value.
Press the OK button is to back default.
4. Set exponential
Press direction button to select “EX”. Exponential can adjust
aileron, throttle and rudder sensitivity as the stick at the middle.
5. Set curve point (normal/advanced)
The box under “EX” shows the curve points.
Select “Curve setting” in More setting function list.
Please refer to Page 27 for detail curve setting.
6. Press EXIT after all the values are finished setting.
38
HELICOPTER
INSTRUCTION
3. SERVO REVERSE
Direction (Rev-reverse, Nor-normal)
Channel
This function is to change the direction of the servos movement.
Setting Method:
Use up/down button to select Servo reverse, OK button is to
enter editing.
Steps:
1. Use direction buttons to select editing part.
2. Use +/- button or OK button to switch the servo movement
direction.
3. Press EXIT after setting.
39
HELICOPTER
INSTRUCTION
4. END POINT
Channel Side Value
It is to adjust the end of individual servo’s travel. The range is
from 0% to 120%.
Setting Method:
Use up or down button to select End point, OK button is to
enter editing.
Steps:
1. Use direction buttons to select editing part.
2. Use +/- button or OK button to set the travel value. Press
OK for a while backs to default.
3. Press EXIT after setting.
40
HELICOPTER
INSTRUCTION
5. SUB TRIM
Channel
Value
High/Low
Sub trim makes small changes or corrections to the neutral
position of each servo. Range is -120 to +120, default setting
is 0.
We recommend that you center the digital trims before making
Sub trim changes, and that you tryto keep all of the Sub trim
values as small as possible. Otherwise, when the Sub trims
are large values, the servo’s range of travel is restricted on
one side.
Setting Method:
Use up or down button to select Sub trim, OK button is to
enter editing.
Steps:
1. Use direction buttons to select editing part.
2. Use +/- button or OK button to set the trim value. Press OK
for a while backs to default.
3. Press EXIT after setting.
41
HELICOPTER
INSTRUCTION
6. SWASH PARAM SETTING
Effection
direction
Value
This function is to adjust the aileron, elevator and pitch travel
range of swash mixing mode.
Setting Method:
Use up or down button to select Swash param setting, OK
button is to enter editing.
Steps:
1. Use direction buttons to select editing part.
2. Use +/- button to set the travel. Press OK button for a while
is to back default(60%).
3. Press EXIT after setting.
42
HELICOPTER
INSTRUCTION
7. AUXILIARY CHANNELS SETTING
Channel
Switch Direction
This function is for channel 5 to channel 9 function setting.
Setting Method:
Use up or down button to select Swash param setting, OK button
is to enter editing.
Steps:
1. Use direction buttons to select editing part.
2. Use +/- button to set the switches or knobs. The switches can
be set from A to F, the knobs can be set as VA, VB, VC, VL,
VR or none(-).
3. Use left or right direction button to set normal or reverse
direction of every channel.
4. Press EXIT after setting.
43
HELICOPTER
INSTRUCTION
8. THROTTLE CURVE SETTING
Current flight mode
Flight mode
Dual rate
Curve picture
(Please refer to Page 27)
Curve point
Throttle curve, together with the throttle stick, can be adjusted
properly to maximize engine performance at a particular pitch
setting.
There are two kinds of curve setting, normal (7 points curve),
advanced (2-10 points curve), the range is between 0%-120%.
The transmitter can set the following curves:
NORM, IDLE1, IDLE2, IDLE3.
Normal curve is based on hovering, to maximize engine performance at a particular pitch setting.
Idle curve is for engine proper work in a 3D flight, with a good
match between throttle and pitch.
44
HELICOPTER
INSTRUCTION
Setting Method:
Use up/down button to select Throttle curve setting, OK button
is to enter editing.
Steps:
1. Flight(NORM IDLE1 IDLE2 IDLE3)
Use direction buttons to select editing part. Use +/- button to
select one curve.
2. Set Dual rate
Use direction button to select “D/R” and edit (one or two values
can be set separately
or together). Press +/- button for seconds can increase or delete
the value. Press OK button for seconds is to back default(60%).
3. Curve point setting(Normal/Advanced)
The below pane shows the points curve.
Select “Curve setting” in “SYS setting”, choose the curve.
For detail curve setting method please refer to Page 27.
4. Press EXIT after setting.
45
HELICOPTER
INSTRUCTION
9. PITCH CURVE SETTING
Flight mode
Dual rate
Curve picture
(Please refer to Page 27)
Curve point
Pitch curve, together with the throttle stick, can be adjusted
properly to maximize engine performance at a particular
pitch setting.
There are two kinds of curve setting, normal (7 points curve),
advanced (2-10 points curve), the range is between 0%-120%.
The transmitter can set the following curves:
NORM, IDLE1, IDLE2, IDLE3.
Normal curve is based on hovering, to maximize engine performance at a particular pitch setting.
Idle curve is for engine proper work in a 3D flight, with a good
match between throttle and pitch.
46
HELICOPTER
INSTRUCTION
Setting Method:
Use up/down button to select PITCH CURVE SETTING, OK button
is to enter editing.
Steps:
1. Flight(NORM IDLE1 IDLE2 IDLE3)
Use direction buttons to select editing part. Use +/- button to
select one curve.
2. Set Dual rate
Use direction button to select “D/R” and edit (one or two values
can be set separately
or together). Press +/- button for seconds can increase or delete
the value. Press OK button for seconds is to back default(60%).
3. Curve point setting(Normal/Advanced)
The below pane shows the points curve.
Select “Curve setting” in “SYS setting”, choose the curve.
For detail curve setting method please refer to Page 27.
4. Press EXIT after setting.
47
HELICOPTER
INSTRUCTION
10. REVOLUTION MIXING
This curve mix adds opposite rudder input to counteract the
changes in torque when the speed and collective pitch of the
blades is changed.
Setting Method:
Use up/down button to select Revolution mixing, OK button is
to enter editing.
Steps:
1. Flight(NORM IDLE1 IDLE2 IDLE3)
Use direction buttons to select editing part. Use +/- button to
select one curve.
2. Set Dual rate
Use direction button to select “D/R” and edit (one or two values
can be set separately or together). Press +/- button for seconds
can increase or delete the value. Press OK button for seconds
is to back default(60%).
3. Curve point setting(Normal/Advanced)
The below pane shows the points curve.
Select “Curve setting” in “SYS setting”, choose the curve.
For detail curve setting method please refer to Page 27.
4. Press EXIT after setting.
48
HELICOPTER
INSTRUCTION
11. TRIM STEP SETTING
This function is to change the rate at which the trim moves
when the TRIM LEVER is activated. The range is from1to
250. Generally larger trim steps are for models with larger
control throws or for first flights to ensure sufficient trim to
properly correct the model. Smaller trim steps are later used
to allow very fine adjustments in flight.
Setting Method:
Use up/down button to select Trim step setting, OK button
is to enter editing.
Steps:
1. Use direction buttons to select editing part.
2. Use +/- button to adjust the size of the step,
3. Repeat as desired for other channels.
3. Press EXIT after setting.
49
HELICOPTER
INSTRUCTION
12. THROTTLE CUT SETTING
This function is to shut off the engine at the end of a flight. The
engine can be stopped with one touch of any switch, eliminating
the need to move the trim to kill the engine and then readjust prior
to each flight. The helicopter THR CUT includes an ON/OFF
throttle position (normally a little above idle). You must move the
THROTTLE STICK back below the set point before the THR-CUT
function can be reset, to avoid sudden engine acceleration.
Setting Method:
Use up/down button to select Throttle cut setting, OK button is
to enter editing.
Steps:
1. Use direction buttons to select editing part.
2. Use +/- button to turn on/off throttle cut function.
3. Use +/- button to set the throttle rate and trim (range is between
+45% to -45%).
4. Use +/- button to set the position.
5. Press EXIT after setting.
50
HELICOPTER
INSTRUCTION
13. FLY MODEL SWITCH
Fly mode
Switch Fly mode statue
This function is to select the flight mode.
Setting Method:
Use up/down button to select Fly model switch, OK button is
to enter editing.
Steps:
1. Use direction buttons to select editing part.
2. Use +/- button to set every fly model.
3. Use +/- button to set fly model ON/OFF position.
4. Press EXIT after setting.
51
HELICOPTER
INSTRUCTION
14. THROTTLE HOLDING SETTING
This function can make the throttle servo operating at a low
speed position at the end of a flight. The range is between
-75% and +75%.
User can set the mix function with rudder under the throttle
holding state and the mix rate (offset).
This function switch can be found in “Fly model switch”.
Setting Method:
Use up/down button to select Throttle holding setting, OK
button is to enter editing.
Steps:
1. Use direction buttons to select editing part.
2. Use +/- button to active or inhibit the mix funtion.
3. Use +/- button to set the throttle holding position.
4. Use +/- button to active or inhibit the rudder mix.
5. Use +/- button to set the mix rate (offset). Press OK button for
seconds can back to default.
6. Press EXIT after setting.
52
HELICOPTER
INSTRUCTION
15. FAIL SAFE
This function is to set responses in case of loss of signal or low RX
battery.
Setting Method:
Use up/down button to select Fail safe, OK button is to enter
editing.
Steps:
1. Use direction buttons to select editing part.
2. Use +/- button to select “hold” or “0.0%”
3. Press OK button to confirm the current parameter.
4. Press EXIT after setting.
53
HELICOPTER
INSTRUCTION
16. TIMER
The flight time of every helicopter is different according to
the different tank of fuel, engine, ESC, etc. Timer function
can alarm you to land before the fuel lacks.
The transmitter can set 3 timers (A, B, C). The longest time
can be set as MM99SS59. The countdown timer can alarm
user before 10 minutes. The alarm will become 2S/1S from
1S/1S in the last 10 seconds. When the countdown timer is
0, the time will add up.
The timer can be seen in the opening screen. Any switch
can be set to control the begin and stop of the time.
Setting Method:
Use up/down button to select TIMER, OK button is to enter
editing.
Steps:
1. Use direction buttons to select editing part.
2. Set timer. WFT09S can set 3 timers (A, B, C).
3. Use +/- button to set MM..SS... Press OK button for seconds
can back to default.
4. Use +/- button to set model.
5. Use +/- button to set control(CTRL).
6. Use +/- button to set the position which can active this
function.
7. Press EXIT after setting.
54
HELICOPTER
INSTRUCTION
17. ADVANCED
To realize an idea fly, there are 21 advanced function in ADVANCED.
Setting Method:
Use up/down button to select ADVANCED, OK button is to enter
editing. +/- button can turn page.
About each advanced functions please read the following pages.
55
HELICOPTER
INSTRUCTION
ADVANCED FUNCTION INTRODUCTION
(1). GYRO SENS SETTING
User can adjust the gyro sensitivity by transmitter,
AVCS gyro (GY) and normal gyro (STD).
Gyro sensitivity switch plug should plug in the fifth channel
of receiver. The auxiliary channel CH 5 won’t have any
function now. User can set sensitivity switch from switch A to F,
and also fly model (NORM, IDLE1,2,3).
Setting Method:
Use up/down button to select GYRO sens setting, OK button
is to enter editing.
Steps:
1. Use direction buttons to select editing part.
2. Use +/- button to set fly model at “MODE”.
3. Use +/- button to active or inhibit “Mix”. Press OK button
for seconds can back
default.
4. Use +/- button to set control switch at “CTRL”.
5. Use +/- button to set the switch position when the function
is active.
6. Use +/- button to set the “Rate”. Press OK button for seconds
can back default.
7. Press EXIT after setting.
56
HELICOPTER
INSTRUCTION
(2). THROTTLE HOVERING SETTING
Throttle hovering setting is fine-tuning adjustments for the
throttle, affecting performance only around the center point
and only in the normal condition.This function can set knob
VA/VB/VC to control, turn right the rotor speed becomes
faster, turn left the rotor speed becomes slower.
Rotor speed changes caused by temperature, humidity,
altitude or other changes in flying conditions are easily
accommodated.
Setting Method:
Use up/down button to select Throttle hovering setting,
OK button is to enter editing.
Steps:
1. Use direction buttons to select editing part.
2. Use +/- button to select “MODEL”.
Use +/- button to active or inhibit this function.
3. Use +/- button to set “Rate”. Press OK button for seconds
can back default.
4. Use +/- button to set control switch.
5. Press EXIT after setting.
57
HELICOPTER
INSTRUCTION
(3). PITCH HOVERING SETTING
Pitch hovering setting is fine-tuning adjustments for the pitch,
affecting performance only around the center point and only in
the normal condition.
This function can set knob VA/VB/VC/VR/VL to control, turn
right the rotor speed becomes faster, turn left the rotor speed
becomes slower.
Rotor speed changes caused by temperature, humidity, altitude
or other changes in flying conditions
are easily accommodated.
Setting Method:
Use up/down button to select Pitch hovering setting, OK button
is to enter editing.
Steps:
1. Use direction buttons to select editing part.
2. Use +/- button to select “MODEL”.
Use +/- button to active or inhibit this function.
3. Use +/- button to set “Rate”. Press OK button for seconds can
back default.
4. Use +/- button to set control switch.
5. Press EXIT after setting.
58
HELICOPTER
INSTRUCTION
(4). HI/LO PIT SETTING
This function is to set the high and low pitch position at different flying modes.
This function can set knob VA/VB/VC/VR/VL to control or
controlled by user ”CTRL MAN”.
IF “CTRL MAN”, the pitch is set by “Rate”, the range is
between 60%-100%.
Setting Method:
Use up/down button to select HI/LO PIT setting, OK button
is to enter editing.
Steps:
1. Use direction buttons to select editing part.
2. Use +/- button to select “MODEL”.
Use +/- button to active or inhibit this function.
3. Use +/- button to set the “Pos”, low or high.
4. Use +/- button to set “Rate”. Press OK button for seconds
can back default.
5. Use +/- button to set control switch.
6. Press EXIT after setting.
59
HELICOPTER
INSTRUCTION
(5). TRIM OFFSET SETTING
This function is to adjust the servo trim at hovering state.
This function is used to automatically change the trim of a
helicopter, for example, when transitioned from hover to
flying at high speed. A clockwise-rotation rotor helicopter
tends to drift to the right at high speed, so an aileron offset
may be applied to offset the helicopter to the left.
The necessary elevator offset varies with model geometry,
so it must be determined by noting collective pitch changes
at high speed.
The rudder offset is affected by both revolution mixing and
trim lever movement while in the offset function.
Setting Method:
Use up/down button to select Trim offset setting, OK button
is to enter editing.
Steps:
1. Use direction buttons to select editing part.
2. Use +/- button to active or inhibit “Mix”.
3. Use +/- button to set the control switch “CTRL”.
4. Use +/- button to set the control switch position “Pos“.
5. Use +/- button to set the channel, eg: ailerion, elevator, etc.
6. Use +/- button to set the mix rate “Rate”. Press OK button for
seconds can back default.
7. Press EXIT after setting.
60
HELICOPTER
INSTRUCTION
(6). DELAY
This function is to delay the aerobatics or throttle cut when
the helicopter is in the air so that to avoid the big trim change.
The Delay function provides a smooth transition between the
trim positions whenever OFFSET, REVO. MIXING, or
THROTTLE HOLD functions are turned on and off.
Setting Method:
Use up/down button to select DELAY, OK button is to enter
editing.
Steps:
1. Use direction buttons to select editing part.
2. Use +/- button to active or inhibit this function. Press OK
button for seconds can back default.
3. Press EXIT after setting.
61
HELICOPTER
INSTRUCTION
(7). GOVERNOR MIXING
This function is to set the governor.
The Governor mixing function is used to adjust the Governor
speed settings from the transmitter.
Setting Method:
Use up/down button to select Governor mixing, OK button is
to enter editing.
Steps:
1. Use direction buttons to select editing part.
2. Use +/- button to active or inhibit “Mix”.
3. Use +/- button to set the mix rate “Rate”. Press OK button
for seconds can back default.
4. Use +/- button to set the control switch “CTRL“.
5. Use +/- button to set the channel and its direction.
6. Press EXIT after setting.
62
HELICOPTER
INSTRUCTION
(8). SWASH AND THR MIXING
This function is to adjust throttle and pitch mix function.
Setting Method:
Use up/down button to select Swash and THR mixing, OK
button is to enter editing.
Steps:
1. Use direction buttons to select editing part.
2. Use +/- button to active or inhibit “Mix”.
3. Press EXIT after setting.
63
HELICOPTER
INSTRUCTION
(9). CURVE SETTING
There are 2 kinds of setting, Normal and Advanced.
1. Setting introduction
Curve setting is one of the functions of WFT09S. We will make
detail description here. You can refer to this detail description
for the other functions which relates to the curve setting.
There are two kinds of curve setting mode: normal setting and
advanced setting.
Normal setting: 7 points curve setting. You can set the curve by
set the 7points value.
Advanced setting: you can add or delete the curve point.
Advanced curve can be added at most 10 points, at least 2 points.
You can not only set the value of each point, but also the position
of each point.
2. Setting method
Turn on the transmitter, press menu, find “More setting”, select
“curve setting”.
There are two modes: normal, advanced.
Normal curve setting: 7 points curve setting. You can edit the
curve point in the left pane.
1. Use left/right direction button to select the editing point. The
curve point is marked by a dashed line.
2. Use +/- button to set the value. Press OK button for a while can
back to default. You can set the 7 points.
3. Press EXIT after setting.
64
HELICOPTER
INSTRUCTION
Advanced curve setting: User can add or delete the curve point.
D/R curve has 10 points and every point can be set. Press +/button for seconds can add/delete curve point. It can at most add
to 10 points and delete to 2 points.
When selecting one point, use left/right button to choose the
point you want to edit, press OK button to enter editing.
Active the cursor, use up/down direction button to set the left
value in the pane, use left/right direction button to set the right
value in the pane.
The black cursor is the editing part, which is marked by a dashed
line.
3.The operation method Of incresing、 decreasing、 moving
the curve points to WFT09S
(1)Increase the curve point
Open the transmitter entre into No,17 advanced setting→confirm→select
No.9 curve setting→ select No.2:Advanced→confirm→exit→exit→select
No.8 throttle curve setting→confirm → At this point we can see a row of
number in bottom left corner inside the box (that is, two 0.0%) are black
shadow → at this time press confirmation button, the black shadow, this
is the cursor (we will introduce it with cursor as follows) will coruscate→
Hold down the (+) key until hear two beeps（ At this time the position
0.0% has increased one curve point, which means that the position 0.0%
have two curve points, of course, there is no need to have two curve
points in one position, so the introduction of how to move curve point will
be shown later）→ Press confirmation button to let cursor stop blinking
→Press the right key to move the curve point to +16.7% → Press
confirmation button, the cursor blink → Hold down the (+) key until hear
two beeps（ At this time the position 0.0% has increased one curve
point） → That means there are two points have been increased, then
about the third curve point, put the cursor in +33.3% position with the
same operation in accordance with the above can be, and there are
seven curves of the original design point, a maximum of can be set to 10
curve points, that is, 3 points can be increased.
65
HELICOPTER
INSTRUCTION
(2)Move curve point operations are as follows
When you want to adjust the data of curve point, such as you
have increased one curve point in the 0.0% position, if you want to
make the increased point to move to +5.5% position, please select
the 0.0% this curve point, that means in the throttle curve settings
menu make the cursor in 0.0% position, → Press confirmation
button to make the cursor blink → Press the right button to move
the right of the data in the cursor blinking area to transfer to +5.5%
→ confirmation
Of course, not just in one place there are two curves of points
should be adjusted then moving curve point, whatever you want to
move the curve point can be adjusted in accordance with this
method. Another point on the operation for reduction of curve point
is to use(-)key stead of (+) key, press OK button, it is simple。
Note: Here is the explanation to the two curves of points in a
position, when the two curves points in one position, the eyes can't
see, but only when the cursor stops blinking, when
you press the right or left button, actually, the numbel below the
cursor haven't any changes, it means the broken line of the curve
point also haven't any changes, that means there are two curve
points in the position now.
The picture can show there are ten curve points.
66
HELICOPTER
INSTRUCTION
(10)-(16). PROG. NOR. MIX1-7
The mix program is to adjust the flying pose. There are 7series
programs with the same setting method. You can set one mix
and one mix with another one mix.
Setting Method
Use up/down button to select PROG. NOR. MIX, OK button is
to enter editing.
Steps:
1. Use direction buttons to select editing part. Set any two
channels mix.
2. Use +/- button to active or inhibit “Mix”.
3. Use +/- button to active or inhibit “Link” and “TRIM”.
4. Use +/- button to active or inhibit “CTRL“.
5. Use +/- button to set the control switch position.
6. Press EXIT after setting.
67
HELICOPTER
INSTRUCTION
(17)-(20). PROG. CUR. MIX1-4
There are 4 curve mix program, the curve is made up by
2 to 10 point.
Setting Method:
Use up/down button to select PROG. CUR. MIX, OK button
is to enter editing.
Steps:
1. Use direction buttons to select editing part. Set any two
channels mix.
2. Use +/- button to active or inhibit “Mix”.
3. Use +/- button to active or inhibit “Link” and “TRIM”.
4. Use +/- button to active or inhibit “CTRL“.
5. Use +/- button to set the control switch position.
6. Set the curve point.(Normal/Advanced). Please refer to
page 27.
7. Press EXIT after setting.
68
HELICOPTER
INSTRUCTION
(21). THROTTLE NEEDLE MIXING
Throttle needle is a pre-programmed mix that automatically
moves an in-flight mixture servo in response to the Throttle
Stick imputs for perfect engine tuning at all throttle settings.
This function is particularly popular with contest pilots who fly
in a large variety of locations, needing regular engine tuning
adjustments, and requiring perfect engine response at all times
and in all maneuvers. Also popular to minimize flooding at idle
of inverted engine installations or installations with a high tank
position. Not need for fuel injection engine, which do this
automatically.
Setting Method
Use up/down button to select Throttle needle mixing, OK
button is to enter editing.
Steps:
1. Use +/- button to active or inhibit this function.
2. Use +/- button to select one curve. There are 3 curves,
NORM, IDLE1, IDLE2, IDLE3.
3. Use direction button to select “D/R”
Edit one or two parameter.
+/- buttons can increase or decrease the value.
Press the OK button is to back default.
4. Use direction button to select “EX”
Edit one or two parameter.
+/- buttons can increase or decrease the value.
Press the OK button is to back default.
EX can adjust aileron, throttle, rudder sensitivity when the
sticks are around the middle.
There are a lot of mixes when “D/R” and “EX” come together.
5. Curve setting method please refer to page 27.
( 22 ). Code matching
Please refer to page 16.
69
AIRPLANE
INSTRUCTION
AIRPLANE
Press Menu and turn on the transmitter to enter SYS SETTING.
Select MODEL SETTING, press OK button to select the model
type.
Restart the transmitter after setting.
70
AIRPLANE
INSTRUCTION
Editing mode and function introduction
1. Opening Screen
Turn on the power switch, the LCD displays as follows.
Voltage
Timer A
Start time
Idle
Model type
Timer B
Throttle trim
display
Timer C
Elevator trim display
Rudder trim display
Aileron trim display
The opening screen displays the voltage, timer, model, aileron,
throttle, elevator and rudder state.
Note: Press EXIT you can see the model name.
Model name
2. Menu Screen
There are “NORMAL SETTING”, “SYS SETTING”, “ADVANCED”.
A. NORMAL SETTING
Turn on the transmitter, press the menu button, the LCD displays
as follows.
1. MONITOR
2. DUAL RATE & EXPONENTIAL SETTING
3. SERVO REVERSE
4. END POINT
5. SUB TRIM
6. AUXILIARY CHANNELS SETTING
7. THROTTLE CURVE SETTING
8. TRIM STEP SETTING
9. FLAPERON
10. FLAP TRIM
11. AIL-DIFF
12. ELEV-FLAP
13. THROTTLE CUT SETTING
14. IDLE DOWN
15. FAIL SAFE
16. TIMER
17. ADVANCED
18. LANGUAGE
Setting method:
1. Use direction button to select the
editing part,use up/down buttons to
select function item. Left/right
direction button to turn page.
2. Press OK button to enter submenu.
The submenu function is in the next
chapter.
3. Press EXIT button to back previous
menu and the data is set automatically.
71
AIRPLANE
INSTRUCTION
B. SYS SETTING
Press Menu and turn on the power switch, the LCD displays as
follows.
Setting method:
1. Use direction button to select the
editing part,use up/down buttons to
select function item. Left/right direction
button to turn page.
1. MODEL SELECTING
2. MODEL NAME
3. MODEL SETTING
4. ATL
5. AIL-2
6. MODULATION SETTING
7. STICK SETTING
8. ADJUSTMENT
9. REST SETTING
10. SEND DATA
11. RECEIVE DATA
12. SOUND
13. CONTRAST SETTING
14. ENGINEER MODEL
15. ABOUT
16. LANGUAGE
2. Press OK button to enter submenu.
The submenu function is in the next
chapter.
3. Press EXIT button to back previous
menu and the data is set automatically.
C. ADVANCED
1. Enter “NORMAL SETTING”, use right direction button to turn page,
select “ADVANCED”.
Press OK button to enter.
Setting method:
1. Use direction button to select the editing part,
use up/down buttons to select function item.
Left/right direction button to turn page.
2. Press OK button to enter submenu. The submenu
function is in the next chapter.
3. Press EXIT button to back previous menu and the
data is set automatically.
72
AIRPLANE
INSTRUCTION
SYS SETTING
1.MODEL SELECTTING
There are 85 airplane models. You can select any one to set.
Setting Method:
Press Menu and turn on the transmitter to enter “SYS SETTING”
Use up/down button to select “MODEL SELECTING”, OK button is
to enter editing.
Steps:
1. Use up/down direction button to select the model.
2. Press OK button to select.
3. Press EXIT after setting.
73
AIRPLANE
INSTRUCTION
2. MODEL NAME
This function is to make new names by users.
Setting Method:
Press Menu and turn on the transmitter to enter “SYS SETTING”
Use up/down button to select “MODEL NAME”, OK button is to
enter editing.
Steps:
1. You can edit the underlined letter.
2. Press OK button to choose the word you like.
3. Press EXIT after setting.
74
AIRPLANE
INSTRUCTION
3. MODEL SETTING
You can select the model type. There are three type: HELI,
ACRO, GLID.
Setting Method:
Press Menu and turn on the transmitter to enter “SYS SETTING”
Use up/down button to select “MODEL SETTING”, OK button is
to enter editing.
Steps:
1. Use up/down direction button to select the model type.
2. Press OK button to confirm.
3. Press EXIT after setting.
75
AIRPLANE
INSTRUCTION
4. ATL
Adjustable travel limit (ATL) makes throttle trim effective only at
low throttle, disabling the trim at high throttle. This prevents
pushrod jamming due to idling trim changes. This function defaults
to ON. If you are not using channel 3 for throttle, you may want trim
operation the same as on all other channels. To do so, set ATL to
OFF.
Setting Method:
Press Menu and turn on the transmitter to enter “SYS SETTING”
Use up/down button to select “ATL”, OK button is to enter editing.
Steps:
1. Use direction buttons to select the editing part.
2. Press +/- button to set ATL function.
3. Press EXIT after setting.
76
AIRPLANE
INSTRUCTION
5. AIL-2
AIL-2 is another channel for aileron.
Setting Method:
Press Menu and turn on the transmitter to enter “SYS SETTING”
Use up/down button to select “AIL-2”, OK button
is to enter editing.
Steps:
1. Use direction buttons to select.
2. Press OK button to confirm.
3. Press EXIT after setting.
77
AIRPLANE
INSTRUCTION
6. MODULATION SETTING
Because of the different receiver modulation PPM/PCMS1024/
2.4G PCMS4096, the transmitter should be accordance with
the receiver modulation.
Setting Method:
Press Menu and turn on the transmitter to enter “SYS SETTING”
Use up/down button to select “Modulation setting”, OK button
is to enter editing.
Steps:
1. Use direction buttons to select the editing part.
2. Press OK button to confirm. Restart the transmitter and it
works.
7.RF setting
Please refer to page 27 .
78
AIRPLANE
INSTRUCTION
8.STICK SETTING
There are 4 kinds of model, you can use up/down direction
button to select the model you preferred.
1-aileron
2-elevator
3-throttle
4-rudder
Setting Method:
Press Menu and turn on the transmitter to enter “SYS SETTING”
Use up/down button to select “STICK SETTING”, OK button is
to enter editing.
Steps:
1. Use direction button to select the editing part.
2. Press up/down button to choose Stick mode.
3. Press EXIT after setting.
79
ARIPLANE
INSTRUCTION
9.Adjustment
This function is to set the central, high and low point of four sticks
when users changed the mode I or II by themselves.
Setting Method:
Press Menu and turn on the transmitter to enter “SYS SETTING”
Use up/down button to select “ADJUSTMENT”, OK button is
to enter editing.
Steps:
1. Use direction button to select the editing part. Take the aileron
adjustment for example .
2. Make the stick in the mid-point location. Press OK button
to select any stick you want to adjust.
3. Select into the Figure 2, when the "center" highlights, press the "ok"
button directly (the mid-point has been adjusted), then enter the high
adjust.
4. The "high” highlights, take the stick gently in the right side
(throttle /elevator in the top, aileron / rudder in the right),press "ok"
button ( the max adjust is OK), enter the low adjustment.
5.The "low" highlights, take the stick gently in the left side (throttle
/elevator in the bottom, aileron / rudder in the left),press "ok" button
(the min adjust is OK).
6. Press OK or RESET to confirm the record or reset.
7. If the record is wrong, press OK will back to step 3.
80

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
XMP Toolkit                     : 3.1-702
Modify Date                     : 2011:09:06 15:46:58+08:00
Create Date                     : 2011:09:06 15:46:53+08:00
Metadata Date                   : 2011:09:06 15:46:58+08:00
Creator Tool                    : PScript5.dll Version 5.2
Format                          : application/pdf
Title                           : WFT09S鑻辨枃20110120
Creator                         : Administrator
Document ID                     : uuid:a707805d-9e48-43eb-9cd9-f7acb38844f7
Instance ID                     : uuid:a65fdfea-b0f2-46f3-a8bb-1fef1857cfa5
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Page Count                      : 45
Author                          : Administrator

EXIF Metadata provided by EXIF.tools