Shin Chuan Computer SC900PDT-BWG Portable Data Terminal User Manual M1000
Shin Chuan Computer Co., Ltd. Portable Data Terminal M1000
Contents
- 1. User Manual - M1000
- 2. User Manual - SC900
User Manual - M1000
User’s Manual
Portable Data Terminal
Model: M1000
SHIN CHUAN COMPUTER CO., LTD.
6F-2, 268, LianCheng Rd., ZhongHe Dist, New Taipei City 23553,
Taiwan(R.O.C)
TEL:886-2-82278801. FAX:886-2-82278832. http://www.sccltd.com.tw
NOV/07/2011 Ver:0.2
• Microsoft Windows CE is a registered trademark of Microsoft Corporation in the
United States and/or other countries.
• Wi-Fi is a registered trademark of the Wi-Fi Alliance.
• Bluetooth is a registered trademark of Bluetooth SIG, Inc.
• All other Trade Names referred to are the Servicemark, Trademark or Registered
Trademark of the respective manufacturers.
Information in this document is subject to change without notice. No part of this
document may be reproduced or transmitted in any form or by any means, electronic
or mechanical, for any purpose, without the express consent of SHIN CHUAN
COMPUTER CO., LTD.
Copyright ©2011 by SHIN CHUAN COMPUTER CO., LTD.
All rights reserved
Revision History:
Date Description Remark
Table of Contents
Chapter 1. Introduction ..............................................................................1-1
1.1 About this Manual.................................................................1-1
1.2 User and Product Safety ......................................................1-2
1.3 Battery Safety.......................................................................1-3
1.4 CE Statement.......................................................................1-4
1.5 FCC Statement.....................................................................1-8
1.5.1 Federal Communication Commission Interference
Statement.....................................................................1-8
1.6 Recycling & disposal instructions. ........................................1-9
1.7 Regulatory information. ........................................................1-9
1.8 Product Labeling ................................................................1-10
1.9 System Specifications ........................................................1-12
1.10 Environment Standard......................................................1-13
1.11 Warranty and after service................................................1-13
Chapter 2. Getting Started .........................................................................2-1
2.1 Check the package...............................................................2-1
2.2 General View of the PDT......................................................2-2
2.2.1 M1000 general view.....................................................2-2
2.3 Charging the Battery Pack ...................................................2-4
2.3.1 Installing the battery pack ............................................2-4
2.3.2 Charging the battery pack with Cradle.........................2-5
2.4. Handling the Device ............................................................2-6
2.4.1 Starting the Device.......................................................2-6
2.4.2 Power on / off...............................................................2-7
2.4.3 Calibration of the touch Screen....................................2-7
2.4.4 To mute the Sound for M1000......................................2-8
2.4.5 Using the Stylus...........................................................2-8
2.4.6 Using the M1000 Keypad.............................................2-8
2.4.9 Using the Earphone ...................................................2-17
2.5 Navigating the Display........................................................2-17
2.5.1 Setting Time and Date ...............................................2-17
2.5.2 Entering the Data.......................................................2-18
2.5.3 The Command Bar.....................................................2-18
2.5.4 The Task Bar..............................................................2-19
2.5.5 The Soft Keypad ........................................................2-19
2.5.6 Setting Up Wireless LAN ...........................................2-19
2.5.7 Reading barcodes, 1D laser version..........................2-25
2.5.8 Installing the MicroSD Card .......................................2-25
2.5.9 Help ...........................................................................2-26
2.6 Power management ...........................................................2-26
2.6.1 Suspend Mode...........................................................2-26
2.6.2 Resuming...................................................................2-27
2.7 Resetting the Device ..........................................................2-27
2.7.1 Software (Warm) Reset..............................................2-27
2.7.2 Cold Reset .................................................................2-28
Chapter 3. Setting.......................................................................................3-1
3.1 Introduction ..........................................................................3-1
3.2 Control Panel .......................................................................3-1
3.2.1 BarCode Controls ........................................................3-1
3.2.2 Backup/Restore .........................................................3-18
3.2.3 Bluetooth Device Properties ......................................3-20
3.2.4 Certificates.................................................................3-24
3.2.5 Date/Time ..................................................................3-26
3.2.6 Device Information.....................................................3-27
3.2.7 Dialing Properties.......................................................3-27
3.2.8 Display Properties......................................................3-29
3.2.9 Input Panel.................................................................3-31
3.2.10 Internet Options .......................................................3-32
3.2.11 Keyboard..................................................................3-35
3.2.12 Network and Dial-up Connections............................3-35
3.2.13 Owner ......................................................................3-40
3.2.14 Password.................................................................3-41
3.2.15 PC Connection.........................................................3-42
3.2.16 Power.......................................................................3-43
3.2.17 Regional Settings.....................................................3-45
3.2.18 Remove Programs...................................................3-47
3.2.19 Storage Manager .....................................................3-47
3.2.20 Stylus .......................................................................3-49
3.2.21 System.....................................................................3-50
3.2.22 USB Function Driver Properties...............................3-52
3.2.23 Volume & Sounds Properties...................................3-52
3.3 Tap Start.............................................................................3-53
3.3.1 Security......................................................................3-53
3.3.2 Bluetooth....................................................................3-54
3.3.3 Boot Manager ............................................................3-55
3.3.4 Brightness..................................................................3-56
3.3.5 Device Power.............................................................3-57
3.3.6 Fn Key Manager ........................................................3-58
3.4 Taskbar and Start Menu .....................................................3-59
Chapter 4. Communication ........................................................................4-1
4.1 Installing & Setting Up Microsoft ActiveSync ........................4-1
4.1.1 Installing Microsoft ActiveSync on the Host PC............4-1
4.1.2 Connecting Device to Host PC ....................................4-1
4.2 Using ActiveSync .................................................................4-1
4.2.1 Setting up a Partnership ..............................................4-1
4.2.2 ActiveSync File Synchronization ..................................4-2
4.3 Networking ...........................................................................4-3
Chapter 5. Software Applications..............................................................5-1
5.1 Introduction ..........................................................................5-1
5.2 Software Applications...........................................................5-1
5.2.1 Internet Explorer ..........................................................5-1
5.2.2 Microsoft WordPad ......................................................5-4
5.2.3 Remote Desktop ..........................................................5-9
5.2.4 Windows Explorer......................................................5-10
5.3 Flash Disk ..........................................................................5-12
5.3.1 Saving to Flash ..........................................................5-12
5.3.2 FlashDisk Location.....................................................5-12
5.3.3 FlashDisk Size ...........................................................5-13
1-1 / 122
Chapter 1. Introduction
Congratulations on purchasing the M1000 Portable Data Terminal, a Microsoft
Windows® CE Rugged Device. Its special combination of features makes it
perfect for using in a wide range of applications. These features as:
Intel® XScaleTM PXA310 624 MHz 32 bits RISC Processor
Windows® CE 6.0 Operating System
128MB SDRAM & 256MB Flash ROM
Open Architecture: User Accessible MicroSD Slot
240 x 320, 2.8” Color TFT Display with Touch Panel
One Numeric-Alpha Keyboards with LED backlight
WLAN 802.11a/b/g Radio Support
Bluetooth V2.0+EDR, Class II Support
Integrated 1D Barcode Scanner or 2D Imager Scanner
1.1 About this Manual
The following chapters contained in this manual are:
Chapter 1 Introduction General information about the Device.
Chapter 2 Getting started Describe the basic use of the Device.
Chapter 3 Setting Provide basic instructions for customizing
the Device.
Chapter 4 Communication Describe how to use all kinds of
communication of the Device.
Chapter 5 Software Application Describe the installed applications on the
Device.
1-2 / 122
1.2 User and Product Safety
z Do not stare into the laser or LED beam directly or shine it into eyes.
z Never use strong pressure onto the screen or subject it to severe impact,
as the LCD panel could become cracked and possibility cause personal
injury. If the LCD panel is broken, never touch the liquid inside because
the liquid irritates the skin.
z Although the Device has passed the test of IP65 standard for water and
dust resistance, avoid prolonged exposure to rain or other concentrated
moisture. Such condition exceeds the IP65 standard, and could result in
water or other contaminants entering into the Device.
z Use only the original approved AC Adapter with the Device. Use of an
unapproved AC Adapter could result in electrical problems, or even cause
a fire or electrical shock to the user.
z Do not disassemble the Device. Servicing should be done by supplier only.
If the Device or accessories gets damaged due to wrong handling or
unauthorized repair, warranty is void. In case the warranty seals are
broken, warranty is void too.
z Make regularly back-up of all important data.
z Under no circumstance will supplier be liable for any direct, indirect,
consequential or incidental damages baring out of the use or inability to
use the hardware and software and/or any data loss, even if supplier has
been informed about the possibility of such damages.
z LASER RADIATION DO NOT STARE INTO BEAM CLASS 2 LASER
PRODUCT
1-3 / 122
1.3 Battery Safety
CAUTION: Risk of Explosion if Battery is replaced by an Incorrect Type.
Dispose of Used Batteries According to the Instructions.
Lithium-ion battery packs might get hot, explode, ignite and/or cause serious
injury if exploded by abusive using. Please follow the safety warnings listed as
below:
z Do not throw the battery pack in fire. Do not expose the battery to high
temperatures.
z Do not connect the positive battery pack with negative battery pack to
each other with any metal object (like wire).
z Do not carry or store battery pack together with metal objects.
z Do not pierce the battery pack with nails or drills, strike the battery pack
with a hammer, step on the battery pack or otherwise expose it to strong
impacts, shocks or excessive force.
z Do not solder onto the battery pack.
z Do not expose battery pack to liquid or allow the battery contacts to get
wet.
z Do not disassemble or modify the battery pack. The battery pack contains
safety and protection measures, which, if damaged, may cause the
battery pack to generate heat, explode or ignite.
z Do not discharge the battery pack using any device except for the
specified device. When it is used in devices other than the specified
devices, the battery pack can be damaged or its life expectancy reduced.
If the device causes any abnormal current to flow, it may cause the battery
pack to become hot, explode or ignite and cause serious injury.
z In the event the battery pack leaks and the fluid gets into one’s eye, do not
rub the eye. Rinse well with water and immediately seek medical care. If
left untreated, the battery fluid could cause damage to the eye.
1-4 / 122
1.4 CE Statement
This device complies with the essential requirements of the R&TTE Directive
1999/5/EC. The following test methods have been applied in order to prove
presumption of conformity with the essential requirements of the R&TTE
Directive 1999/5/EC:
- EN 60950-1: 2006 +A11:2009 +A1:2010
Safety of Information Technology Equipment
- EN 300 440-1 V1.6.1: 2010
- Electromagnetic compatibility and Radio spectrum Matters (ERM); Short
range devices; Radio equipment to be used in the 1 GHz to 40 GHz
frequency range; Part 1: Technical characteristics and test methods
- EN 300 440-2 V1.4.1: 2010
- Electromagnetic compatibility and Radio spectrum Matters (ERM); Short
range devices;Radio equipment to be used in the 1 GHz to 40 GHz
frequency range; Part 2: Harmonized EN covering the essential
requirements of article 3.2 of the R&TTE Directive
- EN 300 328 V1.7.1: 2006
- Electromagnetic compatibility and Radio spectrum Matters (ERM);
Wideband Transmission systems; Data transmission equipment operating
in the 2,4 GHz ISM band and using spread spectrum modulation
techniques; Harmonized EN covering essential requirements under article
3.2 of the R&TTE Directive
- EN 301 893 V1.5.1 (2008-12)
- Broadband Radio Access Networks (BRAN); 5 GHz high performance
RLAN; Harmonized EN covering the essential requirements of article 3.2 of
the R&TTE Directive
- EN 301 511 V9.0.2: 2003
- Global System for Mobile communications (GSM); Harmonized standard
for mobile stations in the GSM 900 and DCS 1800 bands covering essential
requirements under article 3.2 of the R&TTE directive (1999/5/EC)
1-5 / 122
- EN 301 489-1 V1.8.1 (2008-04)
- Electromagnetic compatibility and Radio Spectrum Matters (ERM);
ElectroMagnetic Compatibility (EMC) standard for radio equipment and
services; Part 1: Common technical requirements
- EN 301 489-17 V2.1.1 (2009-05)
- Electromagnetic compatibility and Radio spectrum Matters (ERM);
ElectroMagnetic Compatibility (EMC) standard for radio equipment; Part 17:
Specific conditions for Broadband Data Transmission Systems
- EN 301 489-7 V1.3.1 (2005-11)
- Electromagnetic compatibility and Radio spectrum Matters (ERM);
ElectroMagnetic Compatibility (EMC) standard for radio equipment and
services; Part 7: Specific conditions for mobile and portable radio and
ancillary equipment of digital cellular radio telecommunications systems
(GSM and DCS)
- EN 62209-2: 2010
- Human exposure to radio frequency fields from handheld and
bodymounted wireless communication devices — Human models,
instrumentation, and procedures Part 2: Procedure to determine the
specific absorption rate (SAR) for wireless communication devices used in
close proximity to the human body (frequency range of 30 MHz to 6 GHz)
- EN 62311: 2008
- Assessment of electronic and electrical equipment related to human
exposure restrictions for electromagnetic fields (0 Hz – 300 GHz)
This device is a 2.4 GHz wideband transmission system (transceiver),
intended for use in all EU member states and EFTA countries, except in France
and Italy where restrictive use applies.
In Italy the end-user should apply for a license at the national spectrum
authorities in order to obtain authorization to use the device for setting up
outdoor radio links and/or for supplying public access to telecommunications
and/or network services.
This device may not be used for setting up outdoor radio links in France and in
1-6 / 122
some areas the RF output power may be limited to 10 mW EIRP in the
frequency range of 2454 – 2483.5 MHz. For detailed information the end-user
should contact the national spectrum authority in France.
0560
Česky
[Czech]
[Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se
základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.
Dansk
[Danish]
Undertegnede [fabrikantens navn] erklærer herved, at følgende udstyr
[udstyrets typebetegnelse] overholder de væsentlige krav og øvrige relevante
krav i direktiv 1999/5/EF.
Deutsch
[German]
Hiermit erklärt [Name des Herstellers], dass sich das Gerät [Gerätetyp] in
Übereinstimmung mit den grundlegenden Anforderungen und den übrigen
einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
Eesti
[Estonian]
Käesolevaga kinnitab [tootja nimi = name of manufacturer] seadme [seadme
tüüp = type of equipment] vastavust direktiivi 1999/5/EÜ põhinõuetele ja
nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.
English Hereby, [name of manufacturer], declares that this [type of equipment] is in
compliance with the essential requirements and other relevant provisions of
Directive 1999/5/EC.
Español
[Spanish]
Por medio de la presente [nombre del fabricante] declara que el [clase de
equipo] cumple con los requisitos esenciales y cualesquiera otras disposiciones
aplicables o exigibles de la Directiva 1999/5/CE.
Ελληνική
[Greek]
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ [name of manufacturer] ΔΗΛΩΝΕΙ ΟΤΙ [type of equipment]
ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ
ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
Français
[French]
Par la présente [nom du fabricant] déclare que l'appareil [type d'appareil] est
conforme aux exigences essentielles et aux autres dispositions pertinentes de la
directive 1999/5/CE.
Italiano
[Italian]
Con la presente [nome del costruttore] dichiara che questo [tipo di
apparecchio] è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti
stabilite dalla direttiva 1999/5/CE.
Latviski
[Latvian]
Ar šo [name of manufacturer / izgatavotāja nosaukums] deklarē, ka [type of
equipment / iekārtas tips] atbilst Direktīvas 1999/5/EK būtiskajām prasībām un
citiem ar to saistītajiem noteikumiem.
Lietuvių Šiuo [manufacturer name] deklaruoja, kad šis [equipment type] atitinka esminius
1-7 / 122
[Lithuanian]
reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.
Nederlands
[Dutch]
Hierbij verklaart [naam van de fabrikant] dat het toestel [type van toestel] in
overeenstemming is met de essentiële eisen en de andere relevante
bepalingen van richtlijn 1999/5/EG.
Malti
[Maltese]
Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel tal-prodott]
jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm
fid-Dirrettiva 1999/5/EC.
Magyar
[Hungarian]
Alulírott, [gyártó neve] nyilatkozom, hogy a [... típus] megfelel a vonatkozó
alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.
Polski
[Polish]
Niniejszym [nazwa producenta] oświadcza, że [nazwa wyrobu] jest zgodny z
zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami
Dyrektywy 1999/5/EC.
Português
[Portuguese
]
[Nome do fabricante] declara que este [tipo de equipamento] está conforme
com os requisitos essenciais e outras disposições da Directiva 1999/5/CE.
Slovensko
[Slovenian]
[Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi zahtevami
in ostalimi relevantnimi določili direktive 1999/5/ES.
Slovensky
[Slovak]
[Meno výrobcu] týmto vyhlasuje, že [typ zariadenia] spĺňa základné požiadavky
a všetky príslušné ustanovenia Smernice 1999/5/ES.
Suomi
[Finnish]
[Valmistaja = manufacturer] vakuuttaa täten että [type of equipment = laitteen
tyyppimerkintä] tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja
sitä koskevien direktiivin muiden ehtojen mukainen.
Svenska
[Swedish]
Härmed intygar [företag] att denna [utrustningstyp] står I överensstämmelse
med de väsentliga egenskapskrav och övriga relevanta bestämmelser som
framgår av direktiv 1999/5/EG.
1-8 / 122
1.5 FCC Statement
1.5.1 Federal Communication Commission Interference
Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate this
equipment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Operations in the 5.15-5.25GHz band are restricted to indoor usage only.
Radiation Exposure Statement:
The product comply with the FCC portable RF exposure limit set forth for an
1-9 / 122
uncontrolled environment and are safe for intended operation as described in
this manual. The further RF exposure reduction can be achieved if the product
can be kept as far as possible from the user body or set the device to lower
output power if such function is available.
Note: The country code selection is for non-US model only and is not available
to all US model. Per FCC regulation, all WiFi product marketed in US must
fixed to US operation channels only.
Please use only the specific belt-clips/holsters/accessories supplied by the
SHIN CHUAN COMPUTER CO., LTD. For this product or select a belt-clips,
holsters or similar accessories that have no metallic component in the
assembly and must provide at least 1.5 cm separation distance between the
device and the user's body.
Caution: SCC declares that M1000 ( FCC ID: TQ2-SC900PDT-BWG )is
limited in CH1~CH11 for 2.4GHz by specified firmware controlled
in U.S.A.
The FCC ID of M1000 is TQ2-SC900PDT-BWG
LED AND LASER SAFETY INFORMATION
z Class II LED/Laser Product
z Do not stare at the LED/Laser or shine into eyes
z Do not allow young children to use the product without adult supervision
z Do not replace/repair the LED/Laser, these are not user replaceable
z Do not shine the LED/Laser on a shiny reflective surface
z LASER RADIATION DO NOT STARE INTO BEAM CLASS 2 LASER
PRODUCT
1.6 Recycling & disposal instructions.
Do not throw this product in the home waste bin.
1.7 Regulatory information.
For CE, FCC, RoHS and other Document of Conformities, consult
the Contact Window of Shin Chuan Computer.
1-10 / 122
1.8 Product Labeling
The Device has several labels as shown in Figure 1-1 to 1-2.
A. M1000
Figure 1-1 Product Labeling (Front side view)
Label nr. Description
1 LCD panel protection film
Table 1-1 Front labeling
1-11 / 122
Figure 1-2 Product Labeling (Back side view)
Label nr. Description
2 Laser radiation warning label
3 System and regulatory label
4 Serial / Configuration number
5 Warranty seal
6 Windows CE .NET label
7 FCC Statement
Table 1-2 Rear labeling
1-12 / 122
1.9 System Specifications
The M1000 detailed specifications as follows. Unless otherwise noted, all the
specifications are subject to change without prior notification.
Table 1-3 System Specification
M1000
Processor - Intel PXA310 624MHz 32 bits RISC CPU
Memory - 256MB Flash ROM
- 128MB SDRAM
Display - 240 x 320 2.8” TFT 256K Color LCD with LED
backlight
Audio - One mono speaker for system voice(on lower case)
Expansion Slot - One Micro SD slot
LED
- One Dual-Color LED for Charger Indicator
- One Dual-Color LED for Scanner, Bluetooth and
WLAN Indicator
Radio Support - Wireless LAN: 802.11a/b/g
- Bluetooth: V2.0+EDR, Class II
Scan Engine - Opticon Laser (1D) Engine.
Communication
Ports - USB: Support USB v2.0 client. (Device and Cradle)
Power System
- Standard Li-Ion Battery Pack, 3.7VDC/1840mAh
- Advanced Smart Battery
- Built-in Battery Charger
- 3.7VDC/75mAh rechargeable backup battery
- One Battery Cover Magnet Sensor Switch
- Power Adapter: 100~240VAC, 50/60Hz Input ;
5VDC/1A Output
Keypad / Buttons
M1000
- One Power Button
- Three Barcode Scanner Buttons
- Four Navigation Buttons
- Four Application Buttons
- One 12-key Numeric Keypad
1-13 / 122
M1000
Dimensions and
Weight
- Dimensions:
L: 144 x 62 x 26.2~35.8 mm
- Weight: 240g with Standard Battery Pack(Approx.)
Color - Gray
Peripherals and
Accessories
- Optional: High-Capacity Li-Ion Battery Pack
(3.7VDC/2760mAh)
- Single Dock
Software - Microsoft Windows 6.0 Professional
1.10 Environment Standard
Table 1-4 Environment Standards
Operating Temperature 14oF ~ 122oF( -10oC ~ 50oC)
Storage Temperature -4oF ~ 158oF (-20oC ~ 60oC)
Humidity 5% ~ 95% (non-condensing)
Drop 4ft (1.2m) Drop onto Concrete
Water & Dust proof IP65 Certificated
Vibration MIL STD 810F
1.11 Warranty and after service
Should this Device be malfunctioned, please contact your original retailer
providing information about the product name, the serial number, and the details
about the problem.
2-1 / 122
Chapter 2. Getting Started
2.1 Check the package
Open the package and check all the parts are inside without shortage and
damage:
A. M1000
Figure 2-1 Inside the package
1. M1000 Terminal
2. Hand Strip
3. Stylus Cord.
4. Standard Battery Pack(3.7VDC/1840mAh)
5. Earphone
6. Stylus(Inserted onto Lowercase)
2-2 / 122
2.2 General View of the PDT
2.2.1 M1000 general view
Figure 2-2 M1000 front side view
Figure 2-3 M1000 back side view
2-3 / 122
Table 2-1 Description of M1000 General View
“Red” color Reading barcode 1 Scanner LED
Indicator “Green” color Successful reading
“Red” color Charging battery 2 Charge LED
Indicator “Green” color Battery charged full
“Blue” color Bluetooth Enable 3 3 color LED
Indicator “Green” color WLAN or GPRS Enable
4 LCM / Touch Panel Do specific action through touch panel by stylus
5 Left Scan key
Right Scan key
Main Scan key
Start scanning the barcode by pressing any one
of these three scan keys
6 Power key Puts the terminal into and wakes the terminal
from suspend mode.
7 F1 ~ F4 key The four application keys, hot keys of
application program defined by end user.
8 Navigation key Navigation keys for left, right, up and down
directions
9 Alpha-Numeric keys Numeric keys, Change to Alpha keys after
pressing Alpha key.
10 Alpha key Toggle Alpha-mode for Alpha-Numeric keys
11 Fn key This key is used in combination with other keys
to type special characters and perform system
functions.
12 Enter key This key confirms data entry
14 Scan window A window for scanning of barcode reader
15 Stylus Use the stylus for selecting items and entering
information.
16 Battery Cover Protect Battery pack, keep the switch of battery
cover to leave system from suspend mode
17 Battery cover Latch To keep battery cover locked
18 Hand Strap This strap can be sealed tighter or looser
19 Speaker 1W speaker for audio sound
2-4 / 122
2.3 Charging the Battery Pack
Before using the Device, perform the basic procedure of charging the battery
pack through the following steps.
2.3.1 Installing the battery pack
1. Turn the locking latches (right and left) downwards and lift the battery cover
away from the Device.
Figure 2-4 Detach the battery cover from Device
2. Insert the battery pack into the battery compartment with the label facing
out, and ensuring the battery snaps into place.
Figure 2-5 Insert the battery pack
1
2
1 2
3
2-5 / 122
3. Lock the battery cover by inserting the bottom first, and then press the top in
firmly. Turn the locking latches (right and left) upwards to secure the cover to
the Device.
Figure 2-6 Lock the battery cover
4. Charge time: For the first time to charge the battery pack needs
approximately 6 hours. Subsequent charging time needs approximately 3
hours.
◆. When charging the battery pack, the charge LED indicator on the Device
turns on Red. After the battery pack is fully charged, the charge LED
indicator turns to Green.
2.3.2 Charging the battery pack with Cradle
1. Charging the battery pack with Cradle or Charging the Device with Cradle.
Figure 2-7 Charging with Cradle
1 2
3
2-6 / 122
◆ When charging the battery pack, the charge LED indicator on the Device
turns on Red.
◆ After the battery pack is fully charged, the charge LED indicator turns to
Green.
CAUTION: Please do not remove the Battery pack too long from Device after
you have already full-charged the Battery pack and backup battery pack and
start to use the Device. Otherwise non-saved data will be lost. Please also
keep in mind power the Device off if you want to change the main Battery pack.
2.4. Handling the Device
2.4.1 Starting the Device
Press the Power key to turn on/off the Device. If the Device does not power on,
perform a cold boot. See 2-7 Resetting the Device.
CAUTION: When a battery is fully inserted in Device for the first time,
upon the Device first power up, the device boots and powers on
automatically.
Figure 2-8 Starting the Device
When the Device is powered on for the first
time, it initializes its system. A splash
screen (figure 2-8) appears for a short
period of time followed by the WinCE 6.0
window.
This section offers the basic procedures of
Device using.
2-7 / 122
2.4.2 Power on / off
¾ To turn on the Device
Press the Power key briefly ( ). If the Device does not power on, perform
the cold reset. See chapter 2.7.2.
As the Device initializes its file system, it splash screen displays for about 30
seconds followed by calibration screen. Every time you perform a cold reset,
these screens will also appear.
To turn off the Device, just press the Power key again. This action does not
actually turn off the Device, it only turns the Device into suspend mode. All
running applications remain as you left them, until you press the Power key again
to resume operation of the Device.
2.4.3 Calibration of the touch Screen
On the initial boot-up of the Device, the
stylus calibration screen (Labeled Align
Screen)opens. Use the stylus to press and
hold briefly on the center of each target as
it moves around the screen.
If necessary, adjust the backlight on the
Device to make the screen readable.
When you feel the touch screen function
is poor or the operation does not match
the exact location it should be, please
recalibrate the screen by using the stylus
to tap the Start > Settings >
Control Panel > Stylus, to open the Figure 2-9 Calibration
“Calibration” to recalibrate again.
2-8 / 122
2.4.4 To mute the Sound for M1000
To mute the sound, press the key first, and then press the key to
turn off and turn on the sound.
2.4.5 Using the Stylus
The stylus is located next to hand-strap on the right rear of the Device. The
stylus function is same as the mouse on a PC. Use the stylus to:
1) Navigate the display, select menu item and open optional applications.
2) Tap the characters on soft keyboard panel.
3) Hold the stylus on the screen and drag across the screen to select the list of
multiple items.
CAUTION: Never use a pen, pencil, or other sharp object on the display to avoid
any unexpected damage of the touch screen.
2.4.6 Using the M1000 Keypad
Figure 2-10 M1000 Keypad
Table 2-2 Keypad List
Key Main Function Fn + Main Function Alpha + Fn+ Alpha
+ Main Function
Main BarCode
Scan Key
Power On/Off
2-9 / 122
Key Main Function Fn + Main Function Alpha + Fn+ Alpha
+ Main Function
Up Soft Keyboard
Down Reserved
Left Device Power
Right Brightness
Function change
Escape Tab
Change to letters Caps Change to cap
letters
Backspace Mute Backspace
Enter Del (Delete) Enter
1 ＠ (at) ： ＼
2 ’ (Quotation Marks) A B C
3 ＋ (Plus Sign) D E F
4 Paste G H I
5 € J K L
6 － (Minus Sign) M N O
7 Copy P Q R S
8 ＆ (AND) T U V
9 X (Multiplication) W X Y Z
0 Space
［ ］
＊ (Asterisk) Start Menu . ， ；
＃ ／ (Division) ＝ ％
2-10 / 122
Table 2-3 Special Assembler Key
Assembler Key Functionality Definition
”Alpha” + ”Fn” + ”Enter”
Key Warm Reset Press “Alpha”, “Fn” and
“Enter” buttons simultaneously.
+”Fn”+”Enter”
Key
Cold Reset Press “Power”, “Fn” and
“Enter” buttons simultaneously.
Table 2-4 Definition of main Function
Key Main Function Definition
Main Barcode
Scan Key
The key activates the scan
function of SC900.
Power On/Off
The key puts the terminal into
and wakes the terminal from suspend
mode if this key button is not pressed
more than two seconds.
Up
Move the cursor up one row or line The
cursor will move continuously if button is
pressed continuously.
Application key 1, User can define F1
function from setting.
Down
Move the cursor down one row or line The
cursor will move continuously if button is
pressed continuously.
Application key 2, User can define F2
function from setting.
Left
Move the cursor one character to the left.
The cursor will move continuously if
button is pressed continuously.
Application key 3, User can define F3
function from setting.
Right
Move the cursor one character to the
right. The cursor will move continuously if
button is pressed continuously.
Application key 4, User can define F4
function from setting.
2-11 / 122
Key Main Function Definition
Function change
The key is used in combination
with other keys to type special characters
and perform system functions.
Note: When continue press “Fn” key
twice, the “Fn” key function will be lock
and color change from White( ) to
Yellow ( ). Press again to disable “Fn”
Function.
ESC This key performs a cancel action
Change to letters
1. The key enables you to toggle
between the numeric and alpha modes.
Numeric mode is when you type numbers
with number keys. Alpha mode is when
you type letters with the number keys.
2. When you press key, it appears
“Alpha” icon < > at the Task bar to
indicate Alpha mode is enabled. The
keypad stays in the alpha mode until you
press key again.
Backspace
“Backspace” key, it moves the cursor
back one space each time the key is
pressed. It deletes the previous character
each time it is pressed if you are typing
text. The cursor will move continuously if
button is pressed continuously.
Enter This key confirms data entry
1 Number key “1”
2 Number key “2”
2-12 / 122
Key Main Function Definition
3 Number key “3”
4 Number key “4”
5 Number key “5”
6 Number key “6”
7 Number key “7”
8 Number key “8”
9 Number key “9”
0 Number key “0”
＊ ＊ key
＃ ＃ key
2.4.6.1 Special Function by “Fn” + Main Function
The “Fn” key is used in combination with other keys to type special characters
and perform system functions.
Table 2-5 Special Function key define
Key
Sequence
Fn + Main
Function Definition
SW Keyboard
You must press key, then press
key to use SW Keyboard.
Reserved You can define F2 function.
Device Power
You must press key, then press
key to use Device Power.
2-13 / 122
Key
Sequence
Fn + Main
Function Definition
Backlight
You must press key, then press
key to adjust Brightness.
TAB
1. The “TAB” function is to move the
cursor to the next tab stop or the next
control (on a form)
2. To do this function by pressing
key first, and then pressing key
each time.
Audio Mute
1. Toggle the audio mute/on
2. You must press key, then
press key to enable audio
mute or turn on audio function each
time.
Caps Toggle the Caps function
Del
1. The “Delete” function delete the next
character forward each time.
2. To do “Delete” function by pressing
key first, and then pressing
key each time.
@ Enter an @ by pressing key,
then pressing key.
’
Enter a { ’ } by pressing key, then
pressing key.
2-14 / 122
Key
Sequence
Fn + Main
Function Definition
＋
Enter a plus sign by pressing
key, then pressing key
Paste
1. It is to do “Paste” function.
2. To do this function by pressing
key first, and then pressing
key each time.
Euro symbol
1. It is to do “€” function.
2. To do this function by pressing
key first, and then pressing
key each time.
－ (Minus Sign)
Enter a minus sign by pressing
key, then pressing key.
Copy
1. Copy action.
2. You must press key, then
press key to do “Copy” action
each time.
＆ Enter an AND sign by pressing
key, then pressing key.
＊ Enter an asterisk sign by pressing
key first, and then pressing key.
Space
1. The “Space” function is to move the
cursor one space.
2. To do this function by pressing
key first, and then pressing
key each time.
2-15 / 122
Key
Sequence
Fn + Main
Function Definition
Start Menu
1. It displays the Start menu.
2. To do this function by pressing
key first, and then pressing
key each time.
／
Enter a slash by pressing key
first, and then pressing key.
2.4.6.2 Alpha plane keys by “Alpha” + main Function
1. The key enables you to toggle between the numeric and alpha
modes. Numeric mode is when you type numbers with number keys.
Alpha mode is when you type letters with the number keys.
2. When you press key, it appears “Alpha” icon at the Task bar to
indicate Alpha mode is enabled. It means Alpha mode is disabled if
there isn’t “Alpha” icon at Task bar. The keypad stays in the alpha mode
until you press key again. For an example to type “ cap1 ” word,
press < wait 1 seconds >
.
3. If you want to type a lowercase “ c ”, press
(The key three times, the key is needed if it’s
the first alpha character keying in.). If a letter that is on the same key as
the last letter entered, wait two seconds after you pressed the last key,
then you can enter the correct series of keystrokes to create the next
letter.
4. While you are in the Alpha mode and you press key +
key to initial the “ Caps ” mode, you will render a Caps Lock until you
press key again. Once you are in Caps mode, you stay in
“ Caps “ until it is pressed key again.
5. It appears” “ and “ ” icon at Task Bar during Caps mode.
2-16 / 122
Table 2-6 Alpha + Numeric keys define
To
enter Press the Keys To
enter Press the Keys
： ＼
a A
b B
c C
d D
e E
f F
g G
h H
i I
j J
k K
l L
m M
n N
o O
p P
q Q
r R
s S
t T
u U
v V
w W
x X
y Y
z Z
［ ］
﹒ ，
；
＝ ％
Note:The key is not needed to key in if the character isn’t the first
alpha character being keyed in.
2-17 / 122
2.4.9 Using the Earphone
Connect Earphone to PDT earphone jack connector. if you do want to record
the voice, you have to use the packed Earphone.
Figure 2-11 Earphone
2.5 Navigating the Display
2.5.1 Setting Time and Date
In the Date/Time options, you can change the year, month, date, time, time
zone, or select automatic adjust for Daylight Saving Time. To set or change the
date and time:
1. Select Start > Settings > Control Panel > Date/Time
2. To change the year, select the year or
open a numeric dial. Select the up arrow
to increase the value; select the down
arrow to decrease the value. or you can
type a new value in the field.
3. Select the month to open a pull-down list
of months or press the arrow buttons to
either side of the month to increase or
decrease the month.
4. To change the time, select the hour,
minute, seconds, or AM/PM and select
the up arrow to increase the value;
select /tape the down arrow to decrease
the value. or you can type a new value
in the field. Figure 2-12 Date/Time properties
5. Select your correct time zone from the pull-down list.
6. To automatically adjust the clock for Daylight Saving Time, enable the
checkbox at the bottom of the screen.
7. Select Apply to make save your changes [and make additional
2-18 / 122
modifications] or select OK to exit the Date/Time settings.
2.5.2 Entering the Data
To select and open programs, select Start > Programs from the task bar to
open a list of available programs. or if the program has an icon on the desktop,
double-tap to open it.
There are several ways to enter data on the Device once in an application:
z Use the keypad to enter alpha-numeric characters, Refer to “2.4.6 Using
the M1000 keypad”.
z Use the stylus on the touch screen.
z Select text in the same way you select the text on a PC. Use the stylus to
highlight the desired text by dragging the stylus across the desired text,
double-tapping to select one word and triple-rapping to select an entire
line/paragraph. Refer to “2.5 Navigating the Display” starting.
z Use the soft input panel (digital keyboard) with the stylus.
z Use the bar code scanning to enter data. Press the trigger or “Barcode
Scan” key to initiate a scan. The scanned data will enter the current
application’s open file. Refer to “2.5.7 Reading barcodes, 1D laser
version” starting for more information on using a scanner.
For more information on factory installed applications, Refer to Chapter 5
“ Software Applications”.
2.5.3 The Command Bar
Use the Command bar at top of the screen to perform tasks in programs, such
as opening a file, or editing a file.
Figure 2-13 Task Bar & Command Bar
Command Bar
Task Bar
2-19 / 122
2.5.4 The Task Bar
The Task bar at the bottom of the screen displays the icon, an icon for the
active program, the current time, and system icons for utilities loaded in
memory. The Task bar includes menu names, buttons, and the keyboard icon,
which opens and closes the soft input panel (SIP). The Task bar allows you to
select and close programs. Refer to Figure 2-12 to view the Task bar.
2.5.5 The Soft Keypad
In applications that accept keypad input, the soft input panel (SIP) can be used
to enter data using the stylus. The SIP is digital, QWERTY-style keyboard.
To open the SIP, tap the keyboard icon to open the menu and select Hide
Input Panel to close the keyboard.
Use the stylus to select letters, numbers, or symbols from the Soft Input Panel
for the current application.
2.5.6 Setting Up Wireless LAN
The Summit Client Utility (SCU) is an application designed for end users and
administrators of mobile devices that use a Summit radio module. Using SCU,
an end user can:
z Disable the radio (turn it off) and enable the radio (turn it on)
z View the contents of configuration profiles, or profiles, each of which
houses the RF, security, and other settings for the radio
z Select the profile to be used to connect to a WLAN
z View global settings, which apply to every profile
z View status information on the radio, the access point (AP) or WLAN
router to which it is connected, and the RF connection or link between the
two devices
z To troubleshoot a connection or performance issue, view in-depth
diagnostic information on the connection and the radio, and perform
various troubleshooting and diagnostic tests
After completing an administrator login to the utility, a user can perform these
additional tasks:
z Create, rename, edit, and delete profiles
z Alter global settings, which apply to every profile
SCU provides a graphical user interface (GUI) for access to all of its functions.
Access to these functions also is available through an application
programming interface (API), which an application programmer can use to
enable another utility to manage the radio.
2-20 / 122
To initialize SCU:
z From the Start menu, select Programs
z Select the directory called Summit
z Inside the Summit directory are two items: a directory for the storage of
security certificates and an SCU icon. To run SCU, double-click the SCU
icon
SCU has five tabs: Main, Profile, Status, and Diags, and Global. Each tab is
described in more detail in this section.
Main Tab
Figure 2-14 Main Tab
z Enable/Disable Radio: When the radio is enabled, selecting this button
disables it; when the radio is disabled, selecting this button enables it.
z Active Profile: You can view the name of the active profile and, using the
selection list, select a different profile.
z Status: Indicates the radio’s status.
z Radio Type: Indicates the type of radio in the device. “ABG” means a
Summit radio that supports 802.11a, 802.11b and 802.11g.
z Regulatory Domain: Indicates the regulatory domain or domains for
which the radio is configured “Worldwide” means that the radio can be
used in any domain. The domain cannot be configured by an administrator
or user.
z Auto Profile: enables you to activate or deactivate automatic profile
selection. Tap List and use the dialog box to select a created profile.
z Driver: Indicates the version of the device driver that is running on the
device.
2-21 / 122
z SCU: Indicates the version of SCU that is running on the device.
z About SCU: When tapped, supplies information on SCU that on a
Windows application normally would appear under Help/About.
Profile Tab
Profile settings are radio and security settings that are stored in the registry as
part of a configuration profile. When a profile is selected as the active profile on
the Main tab, the settings for that profile become active. An administrator can
define up to 20 profiles, edit them, and delete them on the Profile tab in SCU.
Profile changes made on the tab are saved to the profile only when the
Commit button is pressed.
Unless it is modified, the Default profile does not specify an SSID, EAP type, or
method of encryption. If the Default profile is the active profile, then the radio
will associate only to an access point that broadcasts its SSID and requires no
EAP type and no encryption.
Figure 2-15 Profile Tab
z Edit Profile: This is used to select the profile to be viewed or, if you are an
administrator, edited.
z Actions: Four actions are available, with the first three available only to
an administrator:
-New: Create a new profile with default settings and give it a unique
name (and then change settings using other selections on the tab).
-Rename: Give the profile a new name, one that is not assigned to
another profile
2-22 / 122
-Delete: Delete the profile, provided that it is not the active profile.
-Scan: Open a window that lists access points that are broadcasting
their SSIDs. Each time you tap the Refresh button, you view an
updated list of APs, with each row showing an AP’s SSID, its received
signal strength indication (RSSI), and whether or not data encryption
is in use (true or false). You can sort the list by clicking on the column
headers. If you are authorized as an administrator, select an SSID
in the list, and tap Commit, you return to the Profile tab to create a
profile for that SSID.
z Radio: Radio attributes in the list box can be selected individually. When
an attribute is selected, the current setting or an appropriate selection box
with the current setting highlighted appears on the right.
z Security: Values for the two primary security attributes, EAP type and
encryption type, are displayed in separate dropdown lists, with the current
values highlighted. When you as an administrator select an EAP type, the
Credentials button appears; when you tap it, a dialog box appears that
enables you to define authentication credentials for that EAP type. When
you as an administrator select an encryption type that requires the
definition of WEP keys or a pre-shared key, the PSKs/WEP Keys button
appears; when you tap it, a dialog box appears that enables you to define
WEP keys or a PSK.
z Commit: To ensure that changes to profile settings made on the tab are
saved in the profile, you must tap the Commit button.
To cause a Summit radio to connect to a typical business WLAN, you must
select a profile that specifies the SSID, EAP type, and encryption type
supported by the WLAN:
z SSID: This is the name or identification of the WLAN.
z EAP type: This is the protocol used to authenticate the device and its user
if the WLAN uses the Enterprise version of Wi-Fi Protected Access (WPA)
and WPA2. SCU supports five EAP types: PEAP with EAP-MSCHAP
(PEAP-MSCHAP), PEAP with EAP-GTC (PEAP-GTC), EAP-TLS, LEAP,
and EAP-FAST
z Encryption: This specifies the type of key used to encrypt and decrypt
transmitted data and how that key is specified or derived. Encryption
options include:
- WPA2 or WPA with dynamic keys (derived from the EAP authentication
process)
- WPA2 or WPA with pre-shared keys
- Static WEP keys
Consult the user’s guide for details on all profile settings, including security
settings.
2-23 / 122
Status Tab
The Status tab provides status information on the radio.
z Active profile
z Radio’s status: Down (not recognized), Disabled, Not Associated,
Associated, or [EAP type] Authenticated
z Client info: Name, IP address, and MAC address
z AP info: Name, IP address, MAC address, beacon period, and DTIM
interval
z Connection info: Channel, data rate, transmit power, signal strength, and
signal quality
Figure 2-16 Status Tab
Diags Tab
Figure 2-17 Diags Tab
2-24 / 122
z (Re)connect: Disable and enable the radio, apply or reapply the current
profile, and attempt to associate and authenticate to the wireless LAN,
logging all activity in the output area at the bottom.
z Release/Renew: Obtain a new IP address through DHCP release/renew,
and log all activity in the output area at the bottom.
z Start Ping: Start a continuous ping to the address in the edit box next to it.
Once the button is clicked, its name and function will change to Stop Ping.
Moving to an SCU window other than Status or Diags also will stop the
ping, as will Pings will continue until you tap the Stop Ping button, move to
an SCU window other than Diags or Status, exit SCU, or remove the radio.
z Diagnostics: Attempt to (re)connect to an AP, and provide a more
thorough dump of data than is obtained with (Re)connect. The dump will
include radio state, profile settings, global settings, and a BSSID list of
APs in the area.
z Save To...: Save the diagnostics output to a file.
Global Tab
Global settings include:
z Radio and security settings that apply to all profiles
z Settings that apply to SCU itself
An administrator can define and change most global settings on the Global
Settings Tab in SCU.
Figure 2-18 Global Tab
The default setting for each global setting ensures reliable operation in most
environments. Consult the user’s guide for details on all global settings.
2-25 / 122
2.5.7 Reading barcodes, 1D laser version.
To use the scanning function, complete the following steps:
1. If you have not already done so, remove the protective plastic film before
using devices equipped with a 1D laser bar code reader.
2. Select Start > Setting > Control Panel > Barcode Controls; complete all
configurations following all description of 3.2.1 BarCode Controls.
3. Run the WordPad software program.
4. Press one of the three barcode reader trigger buttons.
5. Aim the scanning beam at the center of barcode.
6. Good scanning position.
The reading range is from 40 to 300mm distance.
1) Decrease the scanning distance to the bar code when scanning small
barcodes.
2) Increase the scanning distance from the bar code when scanning large
barcodes
3) The scanning area is visible by a red laser beam.
7. Bad scanning position.
1) Make sure that the laser beam sweeps across whole bar code.
2) Scanning operations may fail if the laser beam is positioned as below.
8. upon reading a barcode, the red LED indicator turns on until the trigger is
release or after five seconds. The green LED and the beep tone indicates a
good read.
Note: This product scans using laser light. Never look directly into the laser
light or shine the laser light into the eyes.
2.5.8 Installing the MicroSD Card
1. Turn the locking latches (right and left) downwards and lift the battery cover
away from the Device.
2-26 / 122
Figure 2-19 Detach the battery cover from Device
2. Detach MicroSD Holder and Insert the MicroSD Card into the MicroSD
compartment.
Figure 2-20 Detach the SD Holder from Device
2.5.9 Help
To tap “?” can get help information for each program.
2.6 Power management
2.6.1 Suspend Mode
The Device will go into a suspend mode when it is idle for a period of time. The
idle duration can be customized using the Power control panel (refer to Figure
“Schemes Tab”) Suspend mode works and looks just like you have turned the
unit off. Press the key to suspend the Device, Press the key
again for the Device to resume its Previous state.
Use the Battery power control panel to set the duration to switch state to
Suspend mode when system using battery power. This will save battery power
when Device is not in use.
1
2
4
3
1
3
2
2-27 / 122
Figure 2-21 Schemes Tab-Idle Figure 2-22 Schemes Tab-Suspend
Suspending:
The following conditions will suspend:
z Press <Power> key while the Device is on.
z The duration timer of item “Switch state to Suspend” expires, which
indicates that there has been no use for a specified of time.
z The battery pack is completely discharged.
2.6.2 Resuming
Use one of following methods to resume (wake up the Device):
z Press <Power> key to suspend or resume (wake up).
When a battery pack completely discharges while the unit is in suspend mode,
the Device remains suspended until discharged battery condition is corrected.
2.7 Resetting the Device
2.7.1 Software (Warm) Reset
A warm reset is a transition from the on, idle, or suspend power state that close
all applications, clears the working RAM, but preserves the file system.
Reason to Warm Reset: If an application “ hangs ”, initiate a warm reset to
terminate the application only.
Process to Warm Reset: To a warm reset, press “Alpha” + “Fn” + “Enter”
buttons simultaneously.
2-28 / 122
After Warm Reset:
z The desktop appears with the application shortcuts on the screen.
z The custom settings in the registry are persistent.
2.7.2 Cold Reset
1) You can use Cold Reset to initiate device if WinCE.NET OS lock up or
Warm Reset still can’t work
2) To perform Cold Reset, press “ Power ” + “Fn” + “Enter” buttons
simultaneously.
3) Device will initiate boot up after Cold Reset.
CAUTION:
Only use the Warm Reset. Try warm reset before you initiate Cold
Reset. All applications will be Closed and working RAM and all files will
be cleared if you initiate the Cold Reset. It’s better usually to back up
your files to Flash ROM, Flash Card or PC.
3-1 / 122
Chapter 3. Setting
3.1 Introduction
To view available options for Device setting, tap Start > Settings. Then, there
are three items inside “Control Panel”, “Network and Dial-up” and “Taskbar
and Start”.
3.2 Control Panel
To view the Control Panel and settings you can modify by tapping Start >
Settings > Control Panel.
Figure 3-1 Control Panel
3.2.1 BarCode Controls
CAUTION：Please do not enter into any Barcode Application Program
before settings completing this Barcode.
There are five Tabs for barcode scanner configuration setting:
“Scan” Tab, “Format” Tab, “Bar Codes” Tab, “Settings” Tab
and “Others”. In addition, there is “Settings” for the “Code
Configure” Tab.
3-2 / 122
3.2.1.1 “Scan” Tab
Figure 3-2 Scan Tab
Table 3-1 Basic Description
Field Name Description
Enable
Power
To Enable/Disable Barcode Engine Power.
Default set to Enable.
Enable
Buzzer
To Enable/Disable Buzzer Power.
Default set to Enable.
Vibration Default set to Disable. To Select Vibration type; “Disable”,
“Short”, “2 Times”, “Long”.
Select a method based upon the barcode scanning
application you will use.
Key Emulation A unit continues a unit, fast showing
barcode number.
Copy & Paste Once show barcode number.
Output
Mode
Clipboard Not show the barcode number.
Read Mode To Setup Barcode scan engine Single or Multiple Read
3-3 / 122
3.2.1.2 “Format” Tab
Figure 3-3 Scan Tab
Table 3-2 Basic Description
Field Name Description
Prefix Type the desired label prefix in this text box
Suffix Type the desired label suffix in this text box
None After showing barcode, do not action
Enter After showing the barcode, jump to next
row
Space After showing the barcode, jump one
unit
Terminal
Char
Tab After showing the barcode, jump a
section
Code ID Default set to Disable. When use “Code ID” , the “Prefix”
function will disable automatically.
Select :
“Opticon ID”,
”AIM/ISO15424 ID”,
“Opticon ID + Length(2/6)”,
“AIM/ISO15424 ID + Length(2/6)”,
“Opticon ID + Length(6/6)”,
“AIM/ISO15424 ID + Length(6/6)”.
3-4 / 122
3.2.1.3 “Bar Codes” Tab:
Select the barcode symbologies you plan to scan from the list. Tap to
enable/disable the desired symbologies.
Figure 3-4 Bar Codes Tab
Table 3-3 Bar Codes Description
Barcode Symbology Description
UPC Universal Product Code. The standard bar code
type for retail products in the United States
UPC + 2 Universal product code seen on almost all retail
products in the USA and Canada
UPC + 5 Universal product code seen on almost all retail
products in the USA and Canada
EAN European Article Numbering system. The
international standard bar code for identifying
packages, shipping containers, parts practically
anything
EAN + 2 Added for a total of 14 data digits
EAN + 5 Added for a total of 17 data digits
Code 39 General-purpose code in very wide use worldwide
Tri-Optic Media Barcodes
Codabar Older code often used in library systems,
sometimes in blood ban
Industrial 2 of 5 /
IATA
Older code not in common use
3-5 / 122
Interleaved 2 of 5 Compact numeric code, widely used in industry, air
cargo, other applications
S-Code This symbology encodes like Interleaved 2 of 5
but encodes the last data character as
Industrial 2 of 5. The number of data digits is
therefore always an odd number
Matrix 2 of 5 Used in miscellaneous industrial applications, and
mechanical numbering systems
Chinese Post Used by China Postal Service for automated mail
sorting
Korean Postal Authority code is a fixed length numeric symbology
with a mandatory check digit
IATA A variable length symbology with an optional check
digit and non printable start/stop characters
MSI / Plessey MSI: Variation of the Plessey code commonly used
in USA.
Plessey: Older code commonly used for retail shelf
marking.
Telepen A variable length symbology with an optional check
digit and non printable start/stop characters
UK / Plessey A variable length symbology with a mandatory
checksum and non printable start/stop characters
Code128 A variable length symbology with a mandatory
check digit and non printable start/stop characters
Code 93 Compact code similar to Code 39.
Code 11 Used primarily for labeling telecommunications
equipment.
RSS 14 Reduced Space Symbology. Application
Identifier "01" and 14 digits
RSS Limited Reduced Space Symbology. Application
Identifier "01" and 14 digits
RSS Expanded Reduced Space Symbology. 74 numeric or 41
alpha characters
PDF417 A variable size multi row (stacked) symbology with
selectable error correction levels
Micro PDF417 A variable size multi row(stacked) symbology with
fixed error correction levels
3-6 / 122
3.2.1.4 “Settings” Tab:
Figure 3-5 Settings Tab
Table 3-4 Settings Description
Field Name Description
Barcode To select a type of barcode you wish to set
Transmit Leading Zero After showing the barcode, jump to next row
Transmit Check Digit Whether send check digit by barcode
Barcode Symbologies List
3.2.1.4.1 UPC A
Figure 3-6 UPC A
3-7 / 122
Table 3-5 Settings Description
Field Name Description
Barcode To select a type of barcode you wish to set
Transmit Leading Zero After showing the barcode, jump to next row
Transmit Check Digit Whether send check digit by barcode
3.2.1.4.2 UPC E
Figure 3-7 UPC E
Table 3-6 Settings Description
Field Name Description
Barcode To select a type of barcode you wish to set
Transmit Leading Zero After showing the barcode, jump to next row
Transmit Check Digit Whether send check digit by barcode
Transmit UPC E as UPC A UPC-E label is transmitted in the UPC-A format
3-8 / 122
3.2.1.4.3 EAN
Figure 3-8 EAN
Table 3-7 Settings Description
Field Name Description
Barcode To select a type of barcode you wish to set
EAN 13 Transmit Check
Digit Whether send check digit by barcode
EAN 8 Transmit Check
Digit Whether send check digit by barcode
Enable ISBN Translation
Enable ISSN Translation
EAN-13 label is verified for the correct format and
transmitted as a 10-digit ISBN number, 8 digit
ISSN number.
Enable ISMN Translation In case of ISMN, the character M is
transmitted followed by 9 digits
3-9 / 122
3.2.1.4.4 Code 39
Figure 3-9 Code 39
Table 3-8 Settings Description
Field Name Description
Barcode To select a type of barcode you wish to set
Normal Code 39 The decoded data characters are transmitted
without further translation
Transmit Check Digit Whether send check digit by barcode
Minimum 1 Character -----
3.2.1.4.5 Codabar
Figure 3-10 Codabar
3-10 / 122
Table 3-9 Settings Description
Field Name Description
Barcode To select a type of barcode you wish to set
Normal Codabar Only The decoded data characters are transmitted
without further translation
Transmit Check Digit Whether send check digit by barcode
3.2.1.4.6 Code 2 of 5 / S-Code
Figure 3-11 Code 2 of 5 / S-Code
Table 3-10 Settings Description
Field Name Description
Barcode To select a type of barcode you wish to set
Transmit Check Digit Whether send check digit by barcode
Minimum 5 Characters -----
Space Check for
Industrial 2 of 5
The reading of Industrial 2 of 5 labels with a large
or irregular spacing
3-11 / 122
3.2.1.4.7 IATA
Figure 3-12 IATA
Table 3-11 Settings Description
Field Name Description
Barcode To select a type of barcode you wish to set
Transmit Check Digit Whether send check digit by barcode
3.2.1.4.8 MSI / Plessey
Figure 3-13 MSI / Plessey
3-12 / 122
Table 3-12 Settings Description
Field Name Description
Barcode To select a type of barcode you wish to set
Check MOD 10 The character position CD2 is not transmitted
Transmit Check Digit 1 Whether send check digit by barcode
3.2.1.4.9 Telepen
Figure 3-14 Telepen
Table 3-13 Settings Description
Field Name Description
Barcode To select a type of barcode you wish to set
Numeric Mode The digits 00 up to 99
3-13 / 122
3.2.1.4.10 UK / Plessey
Figure 3-15 UK / Plessey
Table 3-14 Settings Description
Field Name Description
Barcode To select a type of barcode you wish to set
Transmit Check Digits Whether send check digit by barcode
3.2.1.4.11 Code 128
Figure 3-16 Code 128
3-14 / 122
Table 3-15 Settings Description
Field Name Description
Barcode To select a type of barcode you wish to set
EAN 128 Only The decoded data characters are translated to
the EAN 128 format
Enable Concatenation -----
3.2.1.4.12 Code 93
Figure 3-17 Code 93
Table 3-16 Settings Description
Field Name Description
Barcode To select a type of barcode you wish to set
Check Check Digits The check digits are not transmitted
3-15 / 122
3.2.1.4.13 Code 11
Figure 3-18 Code 11
Table 3-17 Settings Description
Field Name Description
Barcode To select a type of barcode you wish to set
Check 1 Check Digit The check digits are not transmitted
Check 2 Check Digits The check digits are not transmitted
3.2.1.4.14 Korean Postal
Figure 3-19 Korean Postal
3-16 / 122
Table 3-18 Settings Description
Field Name Description
Barcode To select a type of barcode you wish to set
Transmit Dash The dash character '-' ( hex 2D ) is Transmitted
3.2.1.4.15 RSS
Figure 3-20 RSS
Table 3-19 Settings Description
Field Name Description
Barcode To select a type of barcode you wish to set
Transmit Check Digit Whether send check digit by barcode
Transmit Application ID Transmission of Application ID
3-17 / 122
3.2.1.5 “Others” Tab:
Figure 3-21 Others Tab Figure 3-22 Set to Factory Default
Figure 3-23 Barcode Firmware Version
Table 3-20 Caption Description
Button Caption Description
Factory Default To set all Barcode parameters to factory default
Firmware Version To get firmware version from Barcode engine
3.2.1.6 Barcode Setup
A. Tap “X” on top right site, to reset all configuration setting of this barcode
into default values, and without Saving.
B. Tap “OK” on top right site, to be decided setting of this barcode. and Save
the Settings.
3-18 / 122
3.2.2 Backup/Restore
Table 3-21 Backup/Restore
ICON ITEM & FUNCTION
1. You can backup/restore system to/from flash disk or inserted
memory card.(FlashDisk, or SD Card) (Figure 3-24)
2. When you launch this AP, it must check backup file in
FlashDisk first. And if you select other storage, it will check
again.
3. Then if it has the file, appeared its date behind “Last backup
date:”; if not, disable “Restore Now” Button.
4. When you press the Backup/Restore Button will be a warning
dialog pop up.(Figure 3-25)
5. When system backup/restoring finished will be a message
dialog will pop up.(Backup: Figure 3-25 Restore: Figure
3-27)
Figure 3-24 Backup/Restore Windows Figure 3-25 Backup Start
3-19 / 122
Figure 3-26 Backup OK Figure 3-27 Restore Start
Figure 3-28 Restore OK-Warm Boot Now Figure 3-29 Restore Settings after Cold
Boot
3-20 / 122
3.2.3 Bluetooth Device Properties
Note: Here are two ways to use Bluetooth Device.
1. Tap “Start” > “Programs” > “Bluetooth” > “Bluetooth Manager”.
2. Tap “Start” > “Settings” > “Control Panel” > “Bluetooth Device
Properties”.
Table 3-22 Bluetooth Device Properties
ICON ITEM & FUNCTION
z “BT Service” Tab: (Figure 3-30)
9 Tap “Bluetooth Device Properties” to enable Bluetooth
device(Figure 3-30).
9 Wait for 10 seconds in order to initialize the Bluetooth
hardware correctly.
9 Tap the “Scan Device” button to initiate a scan for
Bluetooth hardware. The Bluetooth manager lists the
Bluetooth devices that it finds, see Figure 3-33. If
Bluetooth hardware is not found the Bluetooth Hardware
Error window appears, see Figure 3-34. Table 3-23
described the Bluetooth Icons.
9 Double tap the device to connect to on the device list. The
Bluetooth Manager Authentication window appears. Tap
No to connect to the device without authentication, or tap
Yes to authenticate the device before connecting. (Figure
3-35)
9 If the Yes button was selected in the Bluetooth Manager
Authentication window, the enter PIN windows appears.
Enter a PIN (between 1 and 16 characters) in the Enter
PIN: text box, and tap OK. The mobile computer sends the
PIN request to the device for bonding. (Figure 3-36)
9 When prompted, the same PIN must be entered on the
other device. When the PIN is entered correctly on the
other device, the bonded icon appears on the device list.
(Figure 3-37)
z “Serial Port” Tab: (Figure 3-38)
9 Tap “Start” > “Programs” > “Bluetooth” > “Bluetooth SPP
Manager” and Tap “Scan Device”
9 Wait for 10 seconds in order to initialize the Bluetooth
hardware correctly
9 Select which device you want to use
3-21 / 122
9 If want to use Virtual com, only SPP base profiles are
supported.(i.e. Printer, Modem, and LAP).Switch to “Serial
Port” tab, and will see the devices you had trusted or
active. Select the device that you want to map a virtual com
and which virtual com you want to use see Figure 3-38
9 Now COM6 has mapped for BT device see Figure 3-40
Figure 3-30 Bluetooth Device Properties Figure 3-31 Bluetooth Device Properties
3-32 Bluetooth Manager Windows 3-33 Bluetooth Manager Windows
3-22 / 122
Figure 3-34 Bluetooth Error Windows
Figure 3-35 Bluetooth Authenticate
Windows
Figure 3-36 Bluetooth Enter PIN Windows
Figure 3-37 Bluetooth Manager Windows
3-23 / 122
Figure 3-38 Bluetooth SPP Manager
Figure 3-39 Bluetooth Register COM
Success
Figure 3-40 Bluetooth Register COM6
Figure 3-41 Bluetooth File Sync
Note: If the device to which the mobile computer is bonding does not appear in the
list, ensure it is turned on, in discoverable mode, and within range (30 feet / 10
meters) of the mobile computer.
3-24 / 122
Table 3-23 Bluetooth Icon
Icon Description
Unknown device icon Device is not defined
Locked icon Device is locked and cannot be bonded to.
Not locked icon Device is not locked and can be bonded to.
Bluetooth device icon Bluetooth device
Bonded device icon Bonded Bluetooth device
Mobile device icon Device is a mobile device
Phone icon Device is a phone.
Printer icon Device is a printer
Network icon Device is a network.
Linked icon Device is linked.
3.2.4 Certificates
Certificates are used by some applications for establishing trust and for secure
communications.
Certificates are signed and issued by certificate authorities and are valid for a
prescribed period of time. Windows CE manages multiple certificate stores.
Table 3-24 Certificates
ICON ITEM & FUNCTION
z “Store” Tab: (Figure 3-43)
9 In the Stores tab, select the certificate store you wish to
view or modify from the drop-down list (Figure 3-43).
9 The “Trusted Authorities “store lists the top-level
certificates for authorities you trust.(Figure 3-43)
9 The “My Certificates “store contains your personal
certificates, which you use to identify yourself
9 Intermediate certificate authorities that help establish a
chain of trust are stored in the “Other Authorities” store
z “Store” Tab: (Figure 3-44)
3-25 / 122
9 To add a certificate or associated private key to the
selected store, select “Import”(Figure 3-44, Figure 3-45)
9 To view more details of the selected certificate, such as the
expanded name or expiration date, choose “View” (Figure
3-46)
9 To delete the selected certificate from the store, choose
“Remove”
Figure 3-42 Certificates Figure 3-43 Certificates
Figure 3-44 Certificates-Import Figure 3-45 Certificates-Import
3-26 / 122
Figure 3-46 Certificates-View Figure 3-47 Certificates-Help
3.2.5 Date/Time
Table 3-25 Date/Time
ICON ITEM & FUNCTION
z “Date/Time” Tab: (Figure 3-48)
9 Please see the detail information of Chapter 2.5.1 Setting
Time and Date
Figure 3-48 Date/Time Windows Figure 3-49 Date/Time Windows
3-27 / 122
3.2.6 Device Information
Provide Firmware version, Software version, Configuration No, Serial No,
Flash ROM size, RAM size, WIFI MAC address, and Bluetooth ID
Figure 3-50 Device Information
3.2.7 Dialing Properties
Table 3-26 Dialing properties
ICON ITEM & FUNCTION
z “Dialing Properties” Tab: (Figure 3-51)
9 In the When dialing from list, select the “Location” where
you want to change settings.(Figure 3-52)
9 To create a new location, select “New”. Enter the name of
the location, and then select “OK”.(Figure 3-53)
9 Enter or edit the area code and local country code as
needed.
9 In Dial using, select “Tone dialing” or “Pulse dialing”.
Most phone lines are tone.
9 To automatically disable call waiting, select “□ Disable call
waiting by dialing”, select the appropriate number
sequence in the list, or enter a new sequence.
z Editing dialing patterns: (Figure 3-54)
9 Using the codes listed in the topic; revise the dialing
patterns as needed.
3-28 / 122
Notes:
If you need to use character other than the ones listed
here, use manual dialing.
Hyphens and spaces in dialing strings are ignored.
Some modems may not respond to the following
characters, even though your device lets you add them
to the dial string.
Figure 3-51 Dialing Properties
Figure 3-52 Dialing Properties
Figure 3-53 Dialing Properties Figure 3-54 Dialing Properties
3-29 / 122
3.2.8 Display Properties
Table 3-27 Display properties
ICON ITEM & FUNCTION
z “Background” Tab: (Figure 3-55)
9 From the “Image” list, select an image you want as the
background of the desktop.(Figure 3-56)
9 To locate an image in another folder, select
“Browse”.(Figure 3-59)
9 To have the image cover the entire background, select
“ □ Tile image on background ”
z “Appearance” Tab: (Figure 3-60)
9 Change the color scheme:( Figure 3-61)
¾ From the” Scheme” list, select a scheme.
¾ View your choice in the preview box. If you like the
scheme, select “Apply”.
9 Create a custom color scheme:
¾ From the “Item” list, select a display item.
¾ From the “Basic colors” list, select a color, and select
“OK”.
¾ View your color selection(s) in the Preview box.
¾ To save the scheme, select “Save”.
¾ In the “Save this color scheme as” box, enter a name
for the scheme, and select “OK”.
¾ Select “Apply”.
Figure 3-55 Display Properties Figure 3-56 Display Properties
3-30 / 122
Figure 3-57 Display Properties
Figure 3-58 Display Properties
Figure 3-59 Display Properties
Figure 3-60 Display Properties
3-31 / 122
Figure 3-61 Display Properties Figure 3-62 Display Properties-Help
3.2.9 Input Panel
Table 3-28 Display properties
ICON ITEM & FUNCTION
z “Input panel” Tab: (Figure 3-63)
9 Select the input method you want to change.
9 To change the Soft Keyboard Options , tap “Option”
(Figure 3-63)
z “Options” Tab: (Figure 3-64)
9 Change the soft keyboard options as desired, selecting
from:
¾ Large or small keys
¾ Using gestures for space, black-space shift, and enter.
9 To exit the soft keyboard Options, press “OK” on the
control bar, or press the <Enter> key on the keypad.
9 To exit the Input Panel, press “OK” on the control bar, or
press the <Enter> key on the keypad.
3-32 / 122
Figure 3-63 Input Panel Properties Figure 3-64 Input Panel Properties
3.2.10 Internet Options
Table 3-29 Internet Options
ICON ITEM & FUNCTION
z “General” Tab: (Figure 3-65)
9 Type in the URL of desired start page and the desired
search engine. You also change the Cache Size, clear the
Cache and Clear the History
z “Connection” Tab: (Figure 3-66)
9 Modify the network access setting as desired
z “Security” Tab: (Figure 3-67, Figure 3-68)
9 Modify the security settings as desired. You can enable any
of the following by tapping the checkbox
z “Advanced” Tab: (Figure 3-71)
9 Modify the security settings as desired. You can enable any
of the following by tapping the checkbox:
¾ Display Image in pages
¾ Play sounds in pages
¾ Enable scripting
¾ Display a notification about every script error
¾ Underline links-
○ Never
3-33 / 122
○ Always
○ Hover
z “Popups” Tab: (Figure 3-72)
9 Modify the popups settings as desired. You can enable any
of the following by tapping the checkbox
Figure 3-65 Internet Settings-General
Figure 3-66 Internet Settings-Connection
Figure 3-67 Internet Settings-Security
Figure 3-68 Internet Settings
3-34 / 122
Figure 3-69 Internet Settings-privacy
Figure 3-70 Internet Settings
Figure 3-71 Internet Settings-Advanced
Figure 3-72 Internet Settings-Popups
3-35 / 122
3.2.11 Keyboard
Table 3-30 Keyboard
ICON ITEM & FUNCTION
z “Repeat” Tab: (Figure 3-73)
9 To change the amount of time between depressions before
repetition starts, adjust the Repeat delay slider
9 To change the repeat rate, adjust the Repeat rate slider.
9 Test your new setting.
9 Tap “ OK” to exit the “Keyboard” Tab.
Figure 3-73 Keyboard Properties
Figure 3-74 Keyboard Properties
3.2.12 Network and Dial-up Connections
Table 3-31 Network and Dial-up Connections
ICON ITEM & FUNCTION
z “Connection” Tab: (Figure 3-75)
9 To create a “Dial-up Connection”:
¾ Double-tap the “Make New connection”.
¾ In the “Make New Connection” dialog box, enter a name
for the connection.(Figure 3-76)
¾ Select “Dial-Up Connection”.
¾ Select the “Next” button.
3-36 / 122
¾ Select the modem you want use.
¾ Select “Configure” (Figure 3-78)
¾ Under “Connection Reference”, use the default settings
provided. If you can’t connect using these settings, see
your ISP or network administrator for specific
information. If you want to always enter a phone number
before connecting, Select “Manual Dial”. Select “OK”.
¾ Select “TCP/IP Settings”(Figure 3-81) in the “General”
tab. ensure “Use Server-assigned IP address” is
selected. In the “Name Servers” tab, ensure “Use
Server-assigned addresses” is selected, and select
“OK”. If you are unable to connect with these default
settings, see your ISP or network administrator for
specific TCP/IP information.
¾ Select the “Next” button and type the telephone number.
¾ Select the “Finish” button.
The connection you just created appears as an icon in the
“Network and Dial-up Connections” folder.
9 Set up a point-to-Point Protocol(PPP) account with an
ISP and obtain the following information:
¾ Access telephone number
¾ User name
¾ Password
Once you have established an account, create a new
connection on your device. When creating this connection, you
should be able to use all of the default TCP/IP settings provided
in the Make New Connection Wizard. If you can’t connect using
the default settings, contact your ISP or access your ISP’s Web
site for specific TCP/IP information as well as primary and
secondary DNS address.
9 Modify connection setting
¾ Select Start > Settings > Control Panel > Network and
Dialup Connections
¾ Select the icon for connection settings you want to
modify.
¾ Select File > Properties, or double- tap the appropriate
icon.
3-37 / 122
¾ Select desired options. There may be additional settings
that depend on the connection. To modify, select the icon
and select the icon and select Advanced Settings…
from the menu.
Figure 3-75 Network and Dial-up
Connections
Figure 3-76 Network and Dial-up
Connections
Figure 3-77 Network and Dial-up
Connections
Figure 3-78 Network and Dial-up
Connections
3-38 / 122
Figure 3-79 Network and Dial-up
Connections
Figure 3-80 Network and Dial-up
Connections
Figure 3-81 Network and Dial-up
Connections
Figure 3-82 Network and Dial-up
Connections
3-39 / 122
Figure 3-83 Network and Dial-up
Connections
Figure 3-84 Network and Dial-up
Connections
Figure 3-85 Network and Dial-up
Connections
Figure 3-86 Network and Dial-up
Connections
3-40 / 122
3.2.13 Owner
Table 3-32 Owner
ICON ITEM & FUNCTION
z “Identification” Tab: (Figure 3-87)
9 Fill in or edit the data as desired.
9 To have this information displayed when you start your
device, select “Display Owner Identification” at Power
On.
9 To set up identification for remote networks, see Setting up
identification for remote networks.
z “Notes” Tab: (Figure 3-88)
9 Enter the Notes you use to the Display Owner notes
z “Network ID” Tab: (Figure 3-89)
9 Enter the user name, password, and domain name you use
to log on to remote network.
Figure 3-87 Owner Properties Figure 3-88 Owner Properties
3-41 / 122
Figure 3-89 Owner Properties Figure 3-90 Owner Properties-Help
3.2.14 Password
Table 3-33 Password
ICON ITEM & FUNCTION
z “Password Setting” Tab: (Figure 3-91)
9 Enter the password
9 In the “Confirm password “box, enter the password again.
9 To require the password on startup, select “Enable
password protection at power- on“. and/or select
“Enable password protection for screen saver”
9 To exit the Password control panel, press “OK” from the
control bar, or press the <Enter> key on the keypad.
Figure 3-91 Password Properties
3-42 / 122
3.2.15 PC Connection
Table 3-34 PC Connection
ICON ITEM & FUNCTION
z “PC Connection” Tab: (Figure 3-92)
9 Select the first checkbox to enable direct connections to the
desktop computer. (Figure 3-92)
9 Tap the “Change Connection…” button to modify the
connection method from USB
9 To exit the “Change Connection” dialog, press “OK” from
the control bar, or press the <Enter> key on the keypad.
9 To exit the “PC Connection” properties control panel,
press “OK” from the control bar, or press the <Enter> key
on the keypad.
Figure 3-92 PC Connection Figure 3-93 PC Connection
3-43 / 122
3.2.16 Power
Table 3-35 Power
ICON ITEM & FUNCTION
z “Battery” Tab: (Figure 3-94)
9 Provide change level indicators for Main battery and
Backup battery.
9 Provide remaining power capacity of main battery.
9 If a “Main Batteries very Low” warning message shows, the
remaining battery life is around 15 minutes to SC900 shuts
down.(Figure 3-98)
9 The Device will shutdown during the main batteries
capacity is around 3.55V.
9 To exit Battery control panel, press “OK” from the
command bar, or press <Enter> key on keypad.
z “Schemes” Tab: (Figure 3-95)
9 The Scheme Tab allows you to determine the time to
switch state to Suspend mode when using either Battery
Power or AC Power.
9 Select Battery Power or AC Power as the power scheme
from the pull-down list.(Figure 3-96)
9 Select the time to suspend mode from the pull-down list.
(Figure 3-97)
Note:
This ICON inside the Task Bar shows that AC adapter provides
power to the Device and Battery power charging full
The ICON inside the Task Bar shows that Main Batteries
provides the power to the Device
The ICON inside the Task Bar shows that AC adapter provides
the power to the Device and is charging the main batteries.
3-44 / 122
Figure 3-94 Power
Figure 3-95 Power
Figure 3-96 Power Figure 3-97 Power
3-45 / 122
Figure 3-98 Power Figure 3-99 Power-Help
3.2.17 Regional Settings
Table 3-36 Regional Settings
ICON ITEM & FUNCTION
z “Region” Tab: (Figure 3-100)
9 Select the desired location/language.
9 Review the Appearance samples in the bottom half of the
screen.
9 Select the Tab at the top for any settings you wish to
change, Options to modify include Number, Currency,
Time, and Date.(Figure 3-102 ~ Figure 3-105)
Figure 3-100 Regional Settings Figure 3-101 Regional Settings
3-46 / 122
Figure 3-102 Regional Settings Figure 3-103 Regional Settings
Figure 3-104 Regional Settings Figure 3-105 Regional Settings
3-47 / 122
3.2.18 Remove Programs
Table 3-37 Remove Programs
ICON ITEM & FUNCTION
z “Remove Programs” Tab: (Figure 3-106)
9 Only user installed programs can be removed.
¾ Select the program you wish to remove from the list and
press “remove” button.
Figure 3-106 Remove Programs Figure 3-107 Remove Programs
3.2.19 Storage Manager
Table 3-38 Storage Manager
ICON ITEM & FUNCTION
z “Storage Manager” Tab: (Figure 3-108)
9 To change Storage properties control panel default
settings:
Insert Micro Secure digital (MicroSD) storage card into the unit.
¾ Select Start > Settings > Control Panel > Storage
Properties
¾ From the “Storage Info” pull-down list, select the desired
storage device.
¾ You can also format, dismount, and create partitions on
storage devices using this control panel.
3-48 / 122
¾ To save and exit the Storage Properties control panel,
press “OK” from the control bar, or press the <Enter> key
on the keypad.
Caution: Dismounting or formatting the Flash Disk will
erase all files and program stored in Flash Memory
Figure 3-108 Storage Manager Figure 3-109 Storage Manager-New
Figure 3-110 Storage Manager-Delete Figure 3-111 Storage Manager-Properties
3-49 / 122
3.2.20 Stylus
Table 3-39 Stylus
ICON ITEM & FUNCTION
z “Double-Tap” Tab: (Figure 3-112, Figure 3-113)
9 Double-tap the checkerboard grip at a comfortable speed.
9 Double-tap clapboard to test your settings
9 The function is OK if the figures are changed from Figure
3-84 to Figure 3-85.
9 To tap “OK” to exit the Stylus Properties.
z “Calibration”: (Figure 3-114, Figure 3-115)
9 In the Welcome Wizard, you tapped a target with the stylus
to set the amount of pressure needed for the screen to
respond to your stylus taps.
9 Please also see 2.4.3 Calibration of the touch Screen
Figure 3-112 Stylus Properties
Figure 3-113 Stylus Properties
3-50 / 122
Figure 3-114 Stylus Properties Figure 3-115 Stylus Properties
3.2.21 System
Table 3-40 System
ICON ITEM & FUNCTION
z “General” Tab: (Figure 3-116)
9 To show:
¾ Firmware information
¾ Information about Processor type, Memory size,
Expansion card
z “Memory”: (Figure 3-117)
9 Move the slider to adjust memory allocation. Default
storage memory is normally is normally set to about 8MB
with the reminder assigned to Program memory.
9 Press the “OK” key on the Keypad.
Note: the difference is occupied by OS between the RAM
size in Information properties and total memory size of
storage memory and program memory
z “Device Name” Tab: (Figure 3-118)
9 Your device uses this information to identify itself to other
computers.
9 The input panel will open to facilitate data entry.
9 To close the Device Name, press the “OK” button, or press
the <Enter> key on keypad.
3-51 / 122
z “Copyrights” Tab: (Figure3-119)
9 Refer to this tab for specific copyright data. As a user, you
are responsible to read this statement.
Figure 3-116 System Properties
Figure 3-117 System Properties
Figure 3-118 System Properties Figure 3-119 System Properties
3-52 / 122
3.2.22 USB Function Driver Properties
Table 3-41 USB Function Driver Properties
ICON ITEM & FUNCTION
z “USB Function Driver Properties” Tab: (Figure 3-120)
9 The section allow users to set USB Function, such as USB
Serial, USB RNDIS, USB Mass-Storage.(Figure 3-121)
Note: when select any USB function, please warm boot device to
affect USB function
Figure 3-120 USB Function Driver Figure 3-121 USB Function Driver
3.2.23 Volume & Sounds Properties
Table 3-42 Volume & Sound
ICON ITEM & FUNCTION
z “Volume” Tab: (Figure 3-122)
9 The factory default for Volume is the forth level. You can
adjust the volume to your environment and comfort.
¾ Set the volume by adjusting the slider from Soft to
Loud
z “Sounds ” Tab: (Figure3-123)
9 Enable the desired sounds for key clicks, screen taps,
notifications, and applications.
3-53 / 122
Figure 3-122 Volume & Sound Figure 3-123 Volume & Sound
3.3 Tap Start
The Device has some new functions at “Start” menu, Refer to this section for
use.
3.3.1 Security
Tap “Start” > “Security” to use Security Functions.
Figure 3-124 Start Tab Figure 3-125 Security Tab
3-54 / 122
Figure 3-126 Security-User mode Figure 3-127 Security-Application
disabled
3.3.2 Bluetooth
Tap “Start” > “Programs” > “Bluetooth” to use Bluetooth Functions.
Figure 3-128 Bluetooth Figure 3-129 Bluetooth Manager
3-55 / 122
Figure 3-130 Bluetooth-Inquiry Running Figure 3-131 Bluetooth-Devices
3.3.3 Boot Manager
Table 3-43 Boot Manager
ICON ITEM & FUNCTION
z “Boot Manager” Tab: (Figure 3-132)
9 You can Enable/Disable Bluetooth or Wi-Fi power after
Cold Boot, Warm Boot or Suspend/Resume
Figure 3-132 Boot Manager Figure 3-133 Boot Manager
3-56 / 122
3.3.4 Brightness
Table 3-44 Brightness
ICON ITEM & FUNCTION
LCD Brightness: (Figure 3-134)
Set the LCD brightness by adjusting the slider from low to high
Amounts 11 steps:
0%, 10%, 20%, 30%, 40%, 50%, 60%, 70%, 80%, 90%, 100%
LCD Brightness
Timeout
(Figure 3-135)
The table has Never, 10 seconds, 20
seconds, 30 seconds, 40 seconds,1
minute, 3 minutes, 5 minutes and 10
minutes.
Keypad Backlight
Setting(Figure 3-136)
Disable Backlight, Enable Backlight, or
Backlight Always On
Figure 3-134 Brightness Figure 3-135 LCD Brightness Timeout
3-57 / 122
Figure 3-136 Keypad Backlight Setting
3.3.5 Device Power
Table 3-45 Device Power
ICON ITEM & FUNCTION
z “Device Power” Tab: (Figure 3-137)
9 You can Enable/Disable Bluetooth or Wi-Fi power
Figure 3-137 Device Power Figure 3-138 Device Power
3-58 / 122
3.3.6 Fn Key Manager
Table 3-46 Fn-Key
ICON ITEM & FUNCTION
z Fn-Key Setting: (Figure 3-139)
Fn Key The Application Program of default setting
F1 SW Keyboard
F2 Reserved
F3 Device Power
F4 Backlight
9 To assign your favorite application program to Hot Keys.
9 Choose one of Hot Keys from pull-down list.(Figure 3-139)
9 To tap “Browse…” inside “Assign program” applet.(Figure
3-140)
9 Select one application program you want from program list,
then, choose “OK”. (Figure 3-141)
9 Tap Function to select(Figure 3-142)
Figure 3-139 Fn-Key Settings Figure 3-140 Fn-Key Settings
3-59 / 122
Figure 3-141 Fn-Key Settings Figure 3-142 Fn-Key Settings
3.4 Taskbar and Start Menu
Table 3-47 Taskbar and Start menu
ICON ITEM & FUNCTION
z “General” Tab: (Figure 3-144)
9 In this tab, You can change the position of the Taskbar and
Start menu
¾ Is always on top or not
¾ Auto hide or not
¾ Show Clock or not
z “Advanced ” Tab: (Figure 3-145)
Taskbar
and Start
Menu
9 Tap the “Clear” button to remove the contents of the
Documents Menu.
9 Enable “□ Expand Control Panel” to list all icons of
Control Panel from top to bottom.
3-60 / 122
Figure 3-143 Taskbar and Start Menu Figure 3-144 Taskbar and Start Menu-
General
Figure 3-145 Taskbar and Start Menu-
Advanced
Figure 3-146 Taskbar and Start Menu-
Expand Control Panel
4-1 / 122
Chapter 4. Communication
4.1 Installing & Setting Up Microsoft ActiveSync
4.1.1 Installing Microsoft ActiveSync on the Host PC
Microsoft ActiveSync is a file transfer tool to synchronize the files on a PC with
the files on your Device.
To install Microsoft ActiveSync, complete the following steps on the PC:
1. Go to the Microsoft Windows CE.NET website and download the latest
current version of ActiveSync:
http://www.microsoft.com/windowsmobile/en-us/help/synchronize/device
-synch.mspx
2. Install the latest version of Microsoft ActiveSync on the host PC.
3. Open ActiveSync.
4. Select File > Communication Settings from ActiveSync’s menu bar.
5. Go to “Using ActiveSync” on page 4-1 to continue using ActiveSync.
4.1.2 Connecting Device to Host PC
1. You can use a Micro USB cable to connect the Device directly or by a cradle
to Host PC.
․To use the dock, you must first insert the Device into the slot, making sure
that the unit is firmly seated the dock.
2. Connect the dock or Device to the power adapter and power source.
4.2 Using ActiveSync
Use ActiveSync to transfer and synchronize files between the Device and the
Host PC.
4.2.1 Setting up a Partnership
During the Microsoft ActiveSync installation, you were prompted to create a
partnership with your mobile device. When you set up a partnership, you select
synchronization and file conversation settings, which are contained in a file on
your desktop computer. This file enables your desktop computer to recognize
your device. Only devices that have a partnership with a desktop computer can
synchronize information between the two computers.
For more information on partnerships, please refer to your Microsoft
ActiveSync documentation or help file.
4-2 / 122
Transferring Files:
To transfer files, complete the following steps on the host PC:
9 Insert Micro USB cable to Device and connect to PC.
9 After you have established a connection with Device, tap the “Explore”
button at the top of the ActiveSync window (or select Explore from the
File menu).
9 Navigate to the target directory on your Device and copy the desired file
by using the Copy/paste method or dragging and dropping the desired
file(s) into the folder.
4.2.2 ActiveSync File Synchronization
ActiveSync files synchronization requires an ActiveSync partnership between
the Device and the Host PC. Refer to “Setting up a Partnership”, above:
9 Select the files in the synchronization configuration for the Device
partnership.
9 Select Tools > Options from the ActiveSync command bar to configure
the synchronization options.
9 Place the file to be synchronized in the Synchronization folder created
you’re My Documents directory. Defaults to the desktop. During the
ActiveSync connection, all files in the Synchronization folder will be
synchronized to the \My Documents directory on the Device.
Figure 4-1 Connected
4-3 / 122
4.3 Networking
Please see the 3.2.13 Owner, Table 3-31 Owner on page 3-61 for setting
up the network ID. And see the 2.5.6 Setting Up Wireless LAN RF to setup
the 802.11a/b/g Wireless LAN for RF connecting.
5-1 / 122
Chapter 5. Software Applications
5.1 Introduction
You can switch to any software program by tapping the Start Menu.
5.2 Software Applications
5.2.1 Internet Explorer
With Internet Explorer, you can view Web or intranet Web pages on your
device. You will need to use a modem or WLAN to connect to an Internet
server provider (ISP) or network.
5.2.1.1 Connect to the Internet
Before you can view Web pages, you must set up a remote connection to
your ISP or network.
5.2.1.2 Start Internet Explorer
9 Open Internet Explorer by selecting Start > Programs > Internet
Explorer.
9 To get default home page, navigate to the desired default web page.
9 Select View > Internet Options from the command bar.
9 Enter the desired URL in the Start page field.
9 Press the OK button.
Figure 5-1 Internet Explorer
5-2 / 122
5.2.1.3 Navigation Control
Internet Explorer uses sliding menus for application and navigation control. Tap
and drag the sliding menus to the left or right to see the hidden menu items
and toolbars.
To achieve more screen real estate in Internet Explorer, you can hide the
Status bar and View menu. From the top menu bar, go to View > Hide
Toolbars.
Once it is hidden, you must cold reset to access these features again. Refer to
2.7.2 “Cold Reset “for more information.
5.2.1.4 Set up a proxy server
Proxy servers are often used when connecting to the Internet through a local
network, such as a corporate network, for added security.
9 Select View > Internet Options > Connection Tab.
9 Select Access the Internet using a proxy server.
9 Enter the proxy server address and port. For more information, see your
administrator.
9 To bypass the proxy server for local address, such as corporate intranet
pages, select Bypass proxy for local address.
5.2.1.5 Enable Cookies
A cookie file contains information about your identity and preferences so
that a Web site can tailor information to your needs. The Web site sends
the file and it is stored on your mobile device.
9 Select View > Internet Options > Security Tab.
9 Select Allow cookies.
5.2.1.6 Search for an Internet Site
9 Select View > Go > Search to search the web.
5.2.1.7 Go to an Internet address
9 Select Address Bar, if necessary to display the Address bar
9 Enter the address
9 Press “ENTER” key.
5.2.1.8 View previously visited sites
9 Tap the Arrow button at the right site of Address Bar
9 Select the Web Address you want to view.
5-3 / 122
5.2.1.9 Add and view Favorites
9 Go to the page you want add
9 Select Favorites > Add To Favorites.
9 If necessary, locate the folder you want.
9 Confirm or change the name.
9 To view your favorite Web sites, select Favorites and the Web site
you want to view.
Note:To organize your Favorites list, select Favorites > Organize Favorites.
5.2.1.10 Browse Web pages
9 To move to a page you have previously view, select View > Back
9 To move to the next page (provided you have viewed it previously),
Select View > Forward.
9 To return to your Home page, select View > Go > Home.
5.2.1.11 Refresh current page
9 Select View > Refresh.
5.2.1.12 Stop loading a page
9 Select View > Stop.
5.2.1.13 View current page
9 Select View > Internet Options
9 To view the protocol, page type, size, and address, selects the
General tab.
9 To view security information about the page, select the Security tab.
5.2.1.14 View HTML source code
9 While viewing the page, select File > Save As and save the file as .txt
file.
9 Open the file in a word processing program, such as WordPad.
5.2.1.15 Change home and search page settings
9 Open the page you want to use as your home or search page.
9 Select View > Go > Home or Search.
5.2.1.16 Save a copy of current page
You can save Web pages and view them later when you’re disconnected
5-4 / 122
from the Internet or Intranet without using cached memory.
9 Select File > Save As
9 Specify a folder location and give the file name.
5.2.1.17 Copy a Web page to a document
9 Select all or part of the Web page you want to copy.
9 Select Edit > Copy.
9 Go to the document where you want to place the information and
select the location.
9 Select Edit > Paste.
5.2.1.18 Select security Options
9 Select View > Internet Options > Security tab
9 Select the security protocols you want.
5.2.1.19 Change the font size
9 Select View > Text Size and select the desired size.
5.2.2 Microsoft WordPad
You can create and edit documents and templates in WordPad, using
buttons and menu commands that are similar to those used in the desktop
version of Microsoft Word. You can work with files Normal or Outline view.
WordPad documents are usually saved as .pwd files, but you can also
save documents in other file formats, such as .rtf or .doc.
5.2.2.1 Selecting and Editing Text
9 Select text
To select Do this
Any amount of text Drag the stylus over the text.
A word Double-tap the word.
A single paragraph Triple-tap within the paragraph.
An entire document Select Edit > Select All
An picture Tap the picture
9 Find text
¾ To search for text in one part of a document, select that part.
Otherwise, the whole document is searched.
5-5 / 122
¾ Select Edit > Find
¾ Enter the text you want to find. For a paragraph, enter ^p. For a tab
stop, enter ^t.
¾ Select the search options you want.
¾ To continue searching, select Edit > Find > Next.
9 Replace text
¾ To replace text in one part of document, select that part. Otherwise,
the whole document is searched.
¾ Select Edit > Replace.
¾ Enter the text you want to find and the text you want to replace it with.
For a paragraph, enter ^p. For a tab stop, enter ^t.
¾ Select the replacement options you want.
¾ Select Find Next.
¾ On the Find/Replace toolbar, select the appropriate button.
9 Move, copy, or delete text
¾ Select the text you want to move, copy, or delete.
¾ To move or delete text, select the Cut button. To copy the text, select
the Copy button.
¾ To paste the information, move the insertion point to the desired
location, and select the Paste button.
Notes:
z To undo an action, select Edit > Undo.
z To restore the action, select Edit > Redo.
5.2.2.2 Formatting Text
9 Create bulleted and numbered lists
¾ Select the Bullets or Numbering button.
¾ Type the first item.
¾ Press ENTER, type the next item, and repeat as needed.
¾ Select the button again to end list formatting.
Note: To change the number style for the selected list, select Format >
Paragraph, In the Format list, select the style you want.
9 Set the default font
¾ Select Format > Font.
¾ Select the font you want.
5-6 / 122
¾ Select Set As Default
¾ To confirm that your changes will be applied to subsequent
documents you create, select Yes.
Note: To apply the default font and stylus to selected text, select Apply
Default.
9 Select a different font
¾ Select the text you want to change. To select all text, select Edit >
Select All.
¾ From the Font list, select the font you want.
¾ From the Font Size list, select a size.
Note: To see more formatting options, select Format > Font.
9 Change font formatting
¾ Select desired text.
¾ Select the Bold, Italic, or Underline button.
¾ To change the color, select Format > Font and select the color you
want from the Color list.
9 Adjust the paragraph alignment
¾ Select the paragraph you want to align.
¾ Select the Align Left, Center, or Align Right button.
Note: To see more formatting options, select Format > Paragraph.
9 Indent a paragraph
¾ Select the paragraph you want to indent.
¾ Select Format > paragraph.
¾ Adjust the indentation settings as needed.
9 Set tabs
¾ Select Format > Tabs.
¾ Change the tab settings as needed.
5.2.2.3 Adjusting the Display
9 Wrap text in the window
¾ Select View > Wrap to Window.
9 Display the document using the full screen
¾ Select View > Full Screen.
¾ To exit Full Screen view, select Restore.
5-7 / 122
¾ To move the Restore button, drag the bar on the left side.
9 Display or hide scroll bars
¾ Select View > Horizontal Scroll Bar or Vertical Scroll Bar.
9 Zoom in or out
¾ Select View > Zoom, and select the desired percentage.
Note: For Custom, enter the exact percentage and select OK.
5.2.2.4 Working in Outline View
9 Switch between Normal and Outline views
¾ Select View > Normal or Outline.
9 Assign and change outline levels
¾ Select View > Outline.
¾ Select the appropriate buttons on the toolbar.
5.2.2.5 Inserting Symbols
9 Place the insertion point where you want to insert the symbol.
9 Select Tools > Insert Symbols.
9 Select the symbol you want, and then select Insert.
Tips:
If you select a different font ( or subset of a font), a different set of Symbols
will be displayed.
5.2.2.6 Printing a Document
9 Select File > Print.
9 Select the printing options you want.
Tips:
z Port list the available printer ports
z If Network is selected from the Port list, enter the path to the network
printer to the Net Path box.
5.2.2.7 Setting a password for a Document
9 Select File > password.
9 Type and verify the password.
9 You must save the document (File > Save) to return the password.
5-8 / 122
5.2.2.8 Converting Documents
9 About document conversion
If an e-mail program is installed on your device and you receive an attached
Word document or template created in Word version 6.0 or later, WordPad will
convert the file on your device. To view the document, simply open the
attachment in your e-mail program or open the file in the WordPad.
During conversion, some formatting attributes may be changed or lost. To
avoid losing these attributes permanently, close the file after viewing it rather
saving the file on your device. If you save the file, save with a different file
name.
For more information about conversion performed on your device, see the
following topics.
9 Changes caused by Word document conversion
¾ Formatting
z Borders and Shading
Borders and shading are not displayed in WordPad, but are restored
when converted back to a Word document. Shading is not restored
when used in a table, but simple borders are restored.
z Character formatting
Bold, italic, strikethrough, superscript, subscript, and hidden text are
retained and displayed. Other effects are changed or removed.
z Colors
Colors are retained and mapped to colors available on your device.
z Fonts and font sizes
Fonts not supported by your mobile device are mapped to the closest
font available in WordPad.
z Page Formatting
Headers, footers, footnotes, columns, pages setup information, and
style sheets are removed during conversion to WordPad. WordPad
supports built-in headings.
z Paragraph formatting
5-9 / 122
Tabs, alignment, bullets, indentation, simple numbered lists, and
paragraph spacing are retailed and displayed in WordPad.
¾ Pictures
Pictures are removed during conversion.
¾ Table of Contents
Table of Contents text and some formatting are preserved. However, any
text set at right-aligned tab stops may wrap to the next line.
¾ Index
Index text and some formatting are preserved.
¾ Tables
Tables appear as tab-delimited text. Cells containing wrapped text, tabs,
or paragraph markers may be difficult to read. Simple tables are displayed
accurately and restored when you convert the WordPad file back to a
WordPad document.
¾ OLE Objects
OLE Objects are removed during conversion.
¾ Revisions marks, annotations, and comments
Revision marks are visible but cannot be changed. Annotations and
documents are removed during conversion.
5.2.3 Remote Desktop
Using Remote Desktop Connection, you can log on to Windows Terminal
Server and use all programs installed on this server. For example, instead of
running Microsoft Pocket Word, you can run the desktop version of Microsoft
Word.
5.2.3.1 Connecting to Terminal Server
9 Select Start > Programs > Remote Connection, or run ‘CETSC’ from the
command prompt.
9 In the Server box, type or select a Terminal Server name or TCP/IP
address, or select a server in the drop-down list.
9 Select Connect.
5-10 / 122
9 In the Remote Connection window, type your user name, password, and
domain(if required), and then select OK.
Figure 5-2 Remote Connected
5.2.3.2 Disconnecting Without Ending a Session
9 In the Remote Connection window, select Start > Shutdown.
9 Select Disconnect > OK.
Note: If you previously disconnected from a Terminal Server without ending
the session, the Terminal Server will continue to execute any running
processes and Remote Connection can later reconnect to this same
session(if your administrator has configured Remote Connection to
reconnect to disconnected sessions).
5.2.3.3 Disconnecting and Ending a Session
9 In the Remote Connection window, select Start > Shutdown.
9 Select Log Off > OK.
5.2.4 Windows Explorer
Windows Explorer works almost the same on your Device as it does on your
PC. See the topics below for information about the difference in Windows
Explorer on your device.
5.2.4.1 Navigating in File View
9 Go forwards and Back
¾ To go to the previous folder, select Go > Back.
5-11 / 122
¾ To go to the next folder (which you have just viewed), select Go >
Forward.
Figure 5-3 Windows Explorer
9 Use the Go menu
¾ To quickly access the My Documents folder, select Go > My
Documents
¾ To see all of the folders you have accessed, select Go > History.
Double-tap a folder to return to it.
5.2.4.2 Viewing Files as Icons Lists
9 To view icons, select View > Large Icons or Small Icons.
9 To view a list, select View > Details.
5.2.4.3 Working with Files and Folders
9 Create a new folder
¾ If necessary, open the folder where you want the new folder to reside.
¾ Select File > New Folder.
9 Add a folder to your Favorites list
¾ Open the folder
¾ Select Favorites > Add to Favorites.
¾ In the Name box, type the shortcut name.
Tips:
z To open a favorite file or folder, select Favorites and then select the
folder.
5-12 / 122
z To organize your favorites, select Favorites > Organize Favorites.
9 Transfer a file using infrared
¾ To send a file, select it, line up the infrared ports, and select File >
Send To > Infrared Recipient.
¾ To receive a file, line up the infrared ports, and select File > Receive.
5.2.4.4. Creating Desktop Shortcuts
9 Display the file or Web page for which you want to create a Shortcut.
9 Select File > Send to.
9 Select Desktop as Shortcut.
5.2.4.5 Switch to Internet
9 Type a URL in the Address bar.
5.3 Flash Disk
The FlashDisk let the application or a data file can be stored into the Flash
Memory.
Note: The FlashDisk storage memory persists all reset (warm/cold
reboot) conditions and software/firmware updates.
We strongly recommends installing all applications, applets,
programs, and important data files to the FlashDisk location.
Caution:
If an application or a data file is only installed or saved in RAM, a
hard reset will result in the loss of that application or data file.
5.3.1 Saving to Flash
To save an application or data to the Flash Memory, from your current
application, select File > Save As > navigate to the FlashDisk location
and save it.
5.3.2 FlashDisk Location
To access the contents of FlashDisk storage:
9 Double-tap the My Computer icon on the desktop.
9 Double-tap the FlashDisk icon to view FlashDisk.
5-13 / 122
Figure 5-4 FlashDisk
5.3.3 FlashDisk Size
The size of the FlashDisk will vary, depending on the size of system firmware.
9 Inside the FlashDisk directory, tap File > Properties.
9 The FlashDisk Properties dialog:
The number following Free is the amount of memory currently available
on your device.
Figure 5-5 FlashDisk Size