Shure orporated ULXD1H50 Wireless Microphone Transmitter User Manual Exhibit D Users Manual per 2 1033 c3

Download:
Mirror Download [FCC.gov]
Document ID	2068561
Application ID	7v4Qf7bF3dA0k+feKWYLMw==
Document Description	Exhibit D Users Manual per 2 1033 c3
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	336.19kB (4202366 bits)
Date Submitted	2013-09-11 00:00:00
Date Available	2013-09-11 00:00:00
Creation Date	2013-08-06 16:21:37
Producing Software	Adobe PDF Library 10.0.1
Document Lastmod	2013-08-06 16:22:23
Document Title	Exhibit D Users Manual per 2 1033 c3
Document Creator	Adobe InDesign CS6 (Windows)

ULX-D
ULXD4D Dual Receiver
ULXD4Q Quad Receiver
ULX-D Digital Wireless Microphone System
©2012 Shure Incorporated
27A20228 (Rev. 1)
General Description
Shure ULX-D™ Digital Wireless offers uncompromising 24-bit audio quality and RF performance, with intelligent, encryption-enabled hardware, flexible
receiver options, and advanced rechargeability options for professional sound reinforcement.
A breakthrough in wireless audio quality, Shure digital processing enables ULX-D to deliver the purest reproduction of source material ever available in a
wireless system, with a wide selection of trusted Shure microphones to choose from. Extended 20 Hz – 20 kHz frequency range and flat response captures
every detail with clarity, presence, and incredibly accurate low end and transient response. With greater than 120 dB, ULX-D delivers wide dynamic range for
excellent signal-to-noise performance. Optimized for any input source, ULX-D eliminates the need for transmitter gain adjustments.
ULX-D sets a new and unprecedented standard for spectral efficiency and signal stability. The intermodulation performance of ULX-D is an incredible
advancement in wireless performance, enabling a dramatic increase in the number of simultaneous active transmitters on one TV channel. Rock-solid RF
signal with zero audio artifacts extends over the entire range. For applications where secure wireless transmission is required, ULX-D offers Advanced
Encryption Standard (AES) 256-bit encrypted signal for unbreakable privacy.
For scalability and modular flexibility, ULX-D receivers come in single, dual, and even quad channel versions. The dual and quad channel receivers offer
conveniences such as RF cascade, internal power supply, bodypack frequency diversity, audio output channel summing, and Dante™ digital networking
for multi-channel audio over Ethernet. All receivers offer High-Density mode for applications where high channel counts are needed, greatly increasing the
amount of simultaneous channels possible over one frequency band.
Advanced Lithium-ion rechargeability provides extended transmitter battery life over alkaline batteries, battery life metering in hours and minutes accurate to
within 15 minutes, and detailed tracking of battery health status.
Generations ahead of any other available system in its class, ULX-D brings a new level of performance to professional sound reinforcement.
Features
Uncompromising Digital Wireless Audio
Scalable, Intelligent Hardware
• 24-bit/48 kHz digital audio that delivers incredibly clear and accurate
reproduction of the source material
• Single (half-rack), Dual and Quad (full-rack) receiver form factors for any
size installation
• Greater than 120 dB dynamic range through the analog outputs
• Ethernet networking for streamlined setup across multiple receivers
• 20 Hz – 20 kHz frequency range with flat response
• Built-in limiter circuitry prevents digital audio clipping from excessive signal
levels.
• 130 dB dynamic range (typical) using Dante™ digital networked audio
• 60 dB of adjustable system gain easily accessible from the receiver front
panel
• No transmitter gain adjustments needed - optimized for any input source
• Wide selection of trusted Shure Microphones
Extremely Efficient and Reliable RF Performance
• Up to 72 MHz overall tuning range (region dependent)
• Up to 17 active transmitters in one 6 MHz TV channel (22 on an 8 MHz TV
channel)
• High Density mode enables up to 47 active transmitters in one 6 MHz TV
channel (63 in one 8 MHz TV channel), with no audio quality degradation
• Rock-solid signal stability with no audio artifacts over the entire 100 meter
line-of-sight range using standard supplied ½ wave antennas
• Selectable 1, 10, and 20 mW transmitter RF output power
• Optimized scanning automatically finds, prioritizes, and selects the
cleanest frequencies available
• AES 256-bit encryption on all channels
• Wireless Workbench® 6 software compatible for advanced frequency
coordination, monitoring, and control
• AMX/Crestron control
• AXT600 Axient™ Spectrum Manager compatibility
• Rugged metal housing on both transmitters and receiver
• Dual and Quad receivers additionally feature:
• RF cascade ports, internal power supply, and dual Ethernet ports
• Dante™ digital networked audio over Ethernet
• Bodypack Frequency Diversity ensures uninterrupted audio for mission-critical
applications
• Audio summing routes audio signal to multiple outputs
Shure Advanced Power Management
• Adapted from industry-leading Axient™ rechargeable technology
• Lithium-Ion chemistry and intelligent Shure battery circuitry results in
rechargeable batteries with zero memory effect and precision metering
• Provides ULX-D transmitters with unmatched 11+ hours of performance
time
• Transmitters and receivers display remaining battery life in hours and
minutes accurate to within 15 minutes
• AA backwards compatibility
Dual and Quad Receiver Models
The ULXD4 receiver is available in dual channel and quad channel models. Both models share the same feature set and functionality, but differ in the number
of channels available and the number of audio outputs.
The descriptions and procedures in this guide are applicable to either the dual or the quad receiver.
Quickstart Instructions
45°
150 mA
line
line
line
line
mic
mic
mic
mic
1-G: 01CH:03
2-G: 01CH:06
3-G: 01CH:08
4-G: 01CH:12
TxOn
TxOn
TxOn
TxOn
sync
EXIT
control
RF audio
A B
gain
OL
OL
ENTER
control
SCAN
SCAN
GROUP SCAN
push
SCAN COMPLETE
GROUP: 01
OPEN FREQ: 70
RX CHAN FOUND: 4
SCAN
EXIT
line
line
mic
mic
on
Deploy Completed
4 of 4
Channels Set
SYNC TX NOW
SCAN
CHANNEL SCAN
CROUP SCAN
95A15842
on
on
ULXD2
ULXD2
ULXD2
on
AA
SB900
ULXD1
ULXD1
65A15224
control
ULXD4Q
Digital Wireless Receiver
RX1
RF audio
A B
OL
ENTER
OL
gain
RX2
RF audio
A B
gain
RX3
OL
OL
RF audio
A B
gain
RX4
OL
RX1
RF audio
A B
gain
SCAN
OL
push
OL
OL
ULXD2
sync
on
<15 cm (6 in.)
ULXD4
Digital Wireless Receiver
RF audio
A B
OL
OL
EXIT
sync
gain
power
on
!! !
!! !
mic
! ! ! ! ! !!!
!! ! ! ! ! ! !
line
mic
!! !
line
mic
Select RX TO SCAN
1 Receiver
2 Receiver
3 Receiver
!!!
line
mic
mic
push
EXIT
line
mic
EXIT
power
line
gain
OL
ENTER
SCAN
sync
line
RF audio
A B
OL
EXIT
Receiver
ULXD4Q
RX1
RF audio
A B
RX2
gain
OL
ENTER
Digital Wireless Receiver
10 12
control
SEL
RF audio
A B
RX3
gain
OL
SEL
OL
SEL
OL
RF audio
A B
RX4
gain
OL
RF audio
A B
gain
power
OL
SEL
OL
OL
EXIT
sync
SCAN
IR
sync
sync
sync
push
11
13
14
Front Panel
⑪ RF Signal Strength LEDs
① Infrared (IR) Sync Window
Indicate the RF signal strength from the transmitter:
Sends IR signal to the transmitter for sync.
• Amber = Normal (-90 to -70 dBm)
• Red = Overload (greater than -25 dBm)
② Network Icon
Illuminates when the receiver is connected with other Shure devices on the network.
IP Address must be valid to enable networked control.
⑫ Audio LEDs
③ Encryption Icon
Indicate average and peak audio levels:
Illuminates when AES-256 encryption is activated.
LED
Audio Signal Level
Red (6)
-0.1 dBFS
Yellow (5)
-6 dBFS
Yellow (4)
-12 dBFS
Use to navigate and select parameter menus.
Green (3)
-20 dBFS
Green (2)
-30 dBFS
• Push to select a channel or menu item
• Turn to scroll through menu items or to edit a parameter value
Green (1)
-40 dBFS
④ LCD Panel
Displays settings and parameters.
⑤ Scan Button
Press to find the best channel or group.
⑥ Menu Navigation Buttons
⑦ Control Wheel
⑧ Channel Select Button
Description
Overload/ limiter
Normal peaks
Signal Present
Note: In Frequency Diversity mode, simultaneous blinking of the red and
yellow audio LEDs indicates that diversity audio has been routed to this
channel.
Press to select a channel.
⑨ Sync Button
Press the sync button while the receiver and transmitter IR windows are aligned to
transfer settings from the receiver to the transmitter.
⑬ Gain Buttons
⑩ RF Diversity LEDs
Press the ▲▼ gain buttons on the front of the receiver to incrementally adjust gain
from -18 to +42 dB.
Indicate antenna status:
⑭ Power Switch
• Blue = normal RF signal between the receiver and transmitter
• Red = interference detected
• Off = No RF connection between the receiver and transmitter
Powers the unit on or off.
Note: the receiver will not output audio unless one blue LED is illuminated.
output 4
output 3
output 2
Secondary
line
line
line
line
mic
mic
mic
mic
output 1
Primary
Back Panel
① AC Power Input
IEC Connector, 100 - 240 V AC.
② RF Antenna Diversity Input Jack (2)
For antenna A and antenna B.
③ RF Cascade Jack (2)
Passes the RF signal from Antenna A and Antenna B to one additional receiver.
④ Mic/Line Switch (one per channel)
Applies a 30 dB pad in mic position.
⑤ Balanced XLR Audio Output (one per channel)
Connect to a mic or line level input.
⑥ Network Status LED (Green)
One per network port.
• Off = no link
• On = network link
• Flashing = network link active
⑦ Ethernet/Dante Network Secondary Port
Connect to an Ethernet network to enable remote device control via WWB6
software. Also carries Dante digital audio and control signals for audio distribution,
monitoring, and recording - see Dante Network topic.
⑧ Network Speed LED (Amber)
One per network port.
• Off = 10/100 Mbps
• On = 1 Gbps
⑨ Ethernet/Dante Network Primary Port
Connect to an Ethernet network to enable remote device control via WWB6
software. Also carries Dante digital audio and control signals for audio distribution,
monitoring, and recording - see Dante Network topic.
Transmitters
① Power LED
• Green = unit is powered on
• Red = low battery or battery error (see Troubleshooting)
• Amber = power switch is disabled
⑪
② On/Off Switch
Powers the unit on or off.
③ SMA Connector
⑫ ①②
Connection point for RF antenna.
④ LCD Display:
⑨
View menu screens and settings. Press any control button to activate the backlight.
⑤ Infrared (IR) Port
Align with the receiver IR port during an IR Sync for automated transmitter
programming.
ULXD1
④
⑤
⑥
⑥ Menu Navigation Buttons
Use to navigate through parameter menus and change values.
exit
Acts as a 'back' button to return to previous menus or parameters without confirming a value change
enter
Enters menu screens and confirms parameter changes
▼▲
Use to scroll through menu screens and to change parameter values
⑦
⑦ Battery Compartment
⑧
Requires Shure SB900 rechargeable battery or 2 AA batteries.
⑧ AA Battery Adapter
• Handheld: rotate and store in the battery compartment to use a Shure SB900
battery
• Bodypack: remove to accommodate a Shure SB900 battery
⑨ Bodypack Antenna
For RF signal transmission.
⑩ Integrated Antenna
For RF signal transmission.
③
④
⑤
②
⑥
ULXD2
on
⑦
⑧
⑩
⑪ Microphone Cartridge
See Optional Accessories for a list of compatible cartridges.
⑫ TA4M Input Jack
Connects to a 4-Pin Mini Connector (TA4F) microphone or instrument cable.
Advanced Transmitter Features
RF MUTE
Use this to turn on a transmitter without interfering
with the RF spectrum.
Press and hold the exit button during power-on
until RF MUTED is displayed. To un-mute, restart
the transmitter.
Transmitter Input Clip
The following warning displays on the receiver
LCD panel when the transmitter input is clipped:
Tx OVERLOAD
To correct, set MIC.OFFSET to 0 dB and if
necessary, attenuate the signal source.
If the source cannot be attenuated while using a
bodypack transmitter, select INPUT PAD from the
main menu to attenuate the input signal by 12 dB.
MIC.OFFSET
MIC.OFFSET compensates for signal level
differences between transmitters that share the
same receiver channel.
Set the offset gain on a low signal level
transmitter to match a louder transmitter: UTILITY
> MIC.OFFSET
Note: For normal gain adjustments, use the
receiver gain buttons.
Menu Screens
6dB
Receiver Channel
Transmitter
① Receiver Information
① Transmitter Information
② Gain Setting
② Power Lock Indicator
③ Mic. Offset Indicator
③ Battery Runtime Indicator
Use DEVICE UTILITIES > HOME INFO to change the home screen display.
−18 to +42 dB, or Mute.
Indicates offset gain is added to the transmitter.
④ Transmitter Settings
The following information cycles when a transmitter is tuned to the receiver's
frequency:
•
•
•
•
Transmitter Type
Input Pad (Bodypack only)
RF Power Level
Transmitter Lock Status
⑤ Battery Runtime Indicator
Shure SB900 battery: runtime is displayed in minutes remaining.
AA batteries: runtime is displayed with a 5-bar indicator.
⑥ TV Channel
Displays the TV channel that contains the tuned frequency.
⑦ High Density Mode Icon
Scroll ▲▼ at the home screen to change the display.
Indicates power switch is disabled.
Shure SB900 battery: runtime is displayed in minutes remaining.
AA Batteries: runtime is displayed with a 5-bar indicator.
④ Menu Lock Indicator
Indicates menu navigation buttons are disabled.
⑤ Mic. Offset
Displays microphone offset gain value.
⑥ RF Power
Displays RF power setting or High Density mode icon (if enabled).
⑦ Bodypack Input Pad
The input signal is attenuated 12 dB.
⑧ Encryption Icon
Indicates encryption is enabled on the receiver and has been transferred to the
transmitter from a sync.
Displayed when High Density mode is enabled.
Transmitter Setting Icons
Display Icon
Transmitter Setting
Bodypack input is attenuated 12 dB
Offset gain is added to the transmitter
Lo
1 mW RF power level
Nm
10 mW RF power level
Hi
20 mW RF power level
Menu is locked
Power is locked
-No Tx-
No RF connection between a receiver and transmitter
or transmitter OFF
Receiver Home Screen
The home screen displays the following information for each receiver
channel:
• Group and Channel
• Transmitter Status: NoTx or TxOn, battery
icon/remaining battery life
Press the SEL button to access a channel
menu screen.
1 G:01
2 G:01
3 G:01
4 G:01
CH:01
CH:02
CH:03
CH:04
TxOn
TxOn
TxOn
TxOn
Home Screen Display Options
Receiver
Transmitter
The HOME INFO menu provides options to change the information shown on
the receiver home screen:
Home Screen: Press the ▲▼ arrows at the home menu to display one of
the following screens:
DEVICE UTILITIES > HOME INFO
Use the control wheel to select one of the following screen displays.
6dB
push
control
RF audio
A B
gain
power
OL
ULXD4
OL
ENTER
Digital Wireless Receiver
EXIT
sync
SCAN
push
Batteries
The transmitter runs on two AA batteries or the Shure SB900 rechargeable battery. Use the included AA battery adapter when using batteries other than the
Shure SB900.
on
95A15842
on
on
ULXD2
ULXD2
ULXD2
on
on
AA
SB900
ULXD1
ULXD1
65A15224
AA Batteries
Shure SB900 Rechargeable Battery
A 5-segment icon on the receiver and transmitter menu screens
indicates battery charge.
When using an SB900 rechargeable battery, the receiver and
transmitter home screens display the number of hours and
minutes remaining.
For accurate battery runtime monitoring, set the transmitter to the
appropriate battery type: UTILITY > BATTERY > SET.AA.TYPE.
!! ! ! ! ! !
on
sync
RF Power Setting
Battery Indicator
!!!
AA Alkaline Battery Runtime Chart (h:mm)
! ! ! ! ! !!
Detailed information for the SB900 is displayed in the receiver BATTERY
control
RF audio
gain
power
INFO
menu and the transmitter menu:
UTILITY
> BATTERY
> BATT. STATS
!!! !
ULXD2
sync
6 in
cm (
1/10 mW
20 mW
11:00 to 9:35
5:30 to 4:55
9:35 to 7:15
4:55 to 4:00
7:15 to 4:45
4:00 to 2:30
4:45 to 2:25
2:30 to 1:45
2:25 to 00:45
1:45 to 0:25
00:45 to 00:20
00:25 to 00:10
AA Battery Adapter
.)
ULXD4
control
ENTER
EXIT
RF audio
gain
power
ENTER
EXIT
Digital Wireless
Receiver
SCAN
HEALTH
: Displays battery
sync
SCANhealth as a
push
push
percentage of the charge capacity of
a new battery.
CHARGE: Percentage of a full charge
sync
CYCLES: Number of times the battery
has been charged
TEMP: Battery temperature in Celsius
and Fahrenheit
Note: For additional rechargeable battery information, visit www.shure.com.
Shure SB900 Runtime
1 mW
10 mW
20 mW
>11 hours
>11 hours
>7 hour
on
Installing the Battery Contact Cover
Install the included battery contact cover
(65A15947) on the handheld transmitter
to prevent light reflection in broadcast
and performance situations.
1. Align the cover as shown.
2. Slide the cover over the battery
contacts until it is flush with the
transmitter body.
Handheld: Rotate and store the
adapter in battery door when using
Shure SB900
Bodypack: Remove the
adapter when using the
Shure SB900
Note: Slide the cover off before inserting the transmitter in the battery charger.
Setting Gain
Adjust gain at the receiver so that the average signal levels are solid green and yellow with peaks that occasionally trigger the red overload LED. Attenuate
the gain if the signal overloads repeatedly.
Set the XLR output to line-level when possible to optimize sound system noise performance.
System Gain Control
The gain control on the receiver sets the audio signal level for the entire system. This allows adjustments to be made during a live performance. It is not
necessary to change the gain on the transmitter (mic offset) to optimize the gain structure. Any required changes to gain should be made from the receiver.
Adjusting Gain
control
Large Gain Adjustments
RF audio
A B
gain
OL
ULXD4Q
OL
ENTER
Digital Wireless Receiver
RF audio
AB
power
gain
power
RF audio
A B
OL
gain
OL
OL
control
ULXD4
Digital Wireless Receiver
or
EXIT
IR
SCAN
sync
push
Press and hold a
gain button
Press the ▲▼ gain buttons on the front of the
receiver to incrementally adjust gain from -18 to +42
dB.
Reading the Audio Meter
RF audio
A B
OL
OL
Audio peaks illuminate the LEDs for 1 second hold time. The RMS
signal is displayed in real time.
gain
power
OL (Overload) LED: Illuminates red when the internal limiter is
OL
ENTER
EXIT
SCAN
push
Use the control wheel in
the AUDIO menu
Mute
To mute the audio, use Shure Wireless Workbench® software or a thirdparty control device.
engaged, preventing digital clipping.
Receiver Output Level
The following table describes the typical total system gain from the audio input to the receiver outputs:
Output Jack
System Gain (gain control = 0dB)
XLR (line setting)
+24 dB
XLR (mic setting)
-6 dB*
*This setting matches a typical wired SM58 audio signal level.
RF
Transmitter RF Power
Interference Detection
Reference the following table for setting RF Power:
Interference Detection monitors the RF environment for potential sources of
interference which can cause audio dropouts.
RF Power Setting
System Range
Application
1 mW
33 m (100 ft.)
For increased channel reuse at close
distances
10 mW
100 m (330 ft.)
Typical setups
20 mW
>100 m (330 ft.)
For hostile RF environments or long-distance
applications
When interference is identified, the RF LEDs illuminate red and the following
warning displays on the receiver LCD panel.
If the warning display persists or the audio
drops out repeatedly, perform a Scan and
Sync at the first opportunity to find a clear
frequency.
Note: Using the 20 mW setting decreases the transmitter battery runtime
and reduces the number of compatible systems.
Scan and Sync
Use this procedure to tune a receiver and transmitter to the best open channel.
control
ULXD4Q
Important! Before you begin:
RX1
ENTER
Digital Wireless Receiver
RF audio
A B
RX2
gain
RF audio
A B
OL
SEL
RX3
gain
RF audio
A B
OL
OL
OL
OL
OL
EXIT
SCAN
Turn off all transmitters for the systems you are setting up. (This prevents
them from interfering with the frequency scan.)
push
Turn on the following potential sources of interference so they are operating
as they would be during the presentation or performance (the scan will
detect and avoid any interference they generate).
• Other wireless systems or devices
• Computers
• CD players
• Large LED panels
Channel Scan
Group Scan
• Effects processors
EXIT
EXIT
Group Scan
SCAN
SCAN
SCANNING
1. Press the SEL button to select a channel.
2. Perform a channel scan on the receiver: SCAN > GROUP SCAN.
ULXD2
SCAN COMPLETE
!! !
6. Press the sync button on the receiver.
! ! ! ! ! !!!
!! ! ! ! ! ! !
5. Power on the ULXD transmitter.
!! !
G:01 CH:21
485.775 MHz
Rssi: -118 dBm
ULXD2
!!!
4. After the scan completes, the receiver displays the group with the
most available frequencies. Press the flashing ENTER button to deploy
frequencies to each receiver channel.
on
on
!! !
3. Press SCAN to start the scan. SCANNING appears on the LCD during the
scan.
7. Align the IR windows until the receiver IR port illuminates red.
8. When complete, SYNC SUCCESS! appears. The transmitter and receiver
are now tuned to the same frequency.
Manual Frequency Selection
To manually adjust group, channel, or frequency:
RX1
RF audio
A B
gain
OL
OL
control
ULXD4Q
RX1
RF audio
A B
OL
ENTER
Digital Wireless Receiver
OL
gain
RX2
RF audio
A B
OL
OL
gain
RX3
RF audio
A B
OL
OL
gain
RX4
RF audio
A B
gain
power
OL
OL
EXIT
SCAN
sync
1. Press SEL to choose a receiver channel and navigate to the RADIO
menu.
ULXD2
on
push
<15 cm (6 in.)
2. Use the control wheel to adjust the group, channel, or frequency.
3. Press ENTER to save changes.
Multiple System Setup
A setup using networked receivers is the fastest and easiest way to distribute the best open channel to each system. See Networking ULX-D Receivers for
networking details.
Note: Networked receivers must all be within the same frequency band.
Networked Receivers
Non-networked Receivers
1. Turn on all receivers.
1. Turn on all receivers.
2. Conduct a group scan on the first receiver to find available frequencies in
each group: SCAN > GROUP SCAN.
2. Conduct a group scan on the first receiver to find available frequencies in
each group: SCAN > SCAN > GROUP SCAN > SCAN
3. Press ENTER to accept the group number and automatically assign the
next best channel to each receiver on the network. The receiver LEDs will
flash when a frequency has been assigned.
3. When the scan is complete, use the control wheel to scroll through
each group. Press ENTER to select a group that has enough available
frequencies for all channels in the system.
4. Turn on a transmitter and sync to the receiver.
4. Sync a transmitter to each receiver channel.
Important! Leave the transmitter on and repeat this step for each
additional system.
Important! Leave all transmitters on use the following steps to set up
additional receiver channels:
1. Set each additional receiver channel to the same group as the first
receiver: RADIO > G:
2. Conduct a channel scan to find available frequencies within the group:
SCAN > SCAN > CHANNEL SCAN > SCAN
3. When the scan is complete, press ENTER to assign frequencies to each
receiver channel.
10
4. Sync a transmitter to each receiver channel.
High Density Mode
High Density mode creates additional bandwidth for more channels in
crowded RF environments. Frequency efficiency is optimized by running
at 1 mW RF transmit power and narrowing the modulation bandwidth,
allowing for the channel spacing to be reduced from 350 kHz to 125 kHz.
Transmitters can be positioned on adjacent channels with unsubstantial
intermodulation distortion (IMD).
High Density mode is ideal for applications where many channels are
needed in a confined area, transmission distances are short, and the
number of available frequencies is limited. Up to 30 meters of range is
available in High Density mode.
Setting the Receiver to High Density Mode
Frequency Diversity
Frequency Diversity is an advanced ULX-D receiver feature that safeguards
against loss of audio signal caused by RF interference or by power loss in a
transmitter.
In Frequency Diversity mode, the signals from two transmitters from a
common audio source are routed to the outputs of 2 receiver channels. In
the event of interference or power loss, the audio from the good channel is
switched to both outputs to preserve the audio signal. Switching between
channels is seamless and inaudible.
When the receiver senses that the signal quality has improved, audio
routing is restored without interrupting the audio signal.
Note: WWB6 software offers an option to selectively lock the diversity audio
source to a specific transmitter (see Wireless Workbench 6 section).
To set the receiver to High Density mode:
DEVICE UTILITIES > ADVANCED RF > HIGH DENSITY
Best Practices for Frequency Diversity
Use the control wheel to set HIGH DENSITY to ON.
When prompted, sync the transmitter and receiver to enable HIGH DENSITY
mode.
Note: When the receiver is in HIGH DENSITY mode, the following indicators
are shown on the receiver display:
• The HD icon will appear on the receiver display
• The receiver band name will be shown with an "HD" added. (example:
The G50 band will appear as G50HD)
• The transmitter group and channel are assigned letters instead of
numbers (example: G:AA CH:AA)
• Use the same microphone type and model for each transmitter
• Place microphones within close proximity to the source
• Use the gain controls to match the output levels for each receiver channel
• If Audio Summing is active, use a Y-cable (Shure AXT652) to connect the
bodypacks to a single audio source to prevent comb filtering
Choosing Diversity Output Routing
The following receiver channel routing output options are available:
• 1+2
• 3 + 4 (quad only)
• 1 + 2 / 3 + 4 (quad only)
Best Practices for High Density Mode
• When band planning, position ULX-D High Density channels in a range of
frequencies separated from other devices.
• Use a separate RF zone for ULX-D High Density channels to prevent
intermodulation distortion from other devices.
• During High Density channel scanning, turn on all other transmitters and
move them to their intended position.
• Perform a walk test to verify transmitter range
• If using custom groups, the groups loaded into the receiver must be
compatible with High Density mode
To enable Frequency Diversity and select a routing option:
DEVICE UTILITIES > FREQ DIVERSITY
Use the control wheel to choose a routing option, and then press ENTER.
Note: Choose OFF to disable Frequency Diversity.
Frequency Diversity and Encryption
Enabling Encryption while in Frequency Diversity mode provides an
additional layer of protection by only passing audio from the most recently
synced encrypted transmitter for each receiver channel.
Audio Summing
Audio summing allows the dual and quad receivers to function as a 2 or 4 channel mixer, respectively. All XLR outputs of the selected channels provide the
summed audio. For example, when 1 + 2 is selected (see diagram), the XLR outputs of channels 1 and 2 supply the summed audio of the two channels.
Choosing an Audio Summing Mode
The following Audio Summing mode options are available:
3+4
1+2
1+2+3+4
1+2/3+4
1 +2
1 +2
1+2
1+2
3+4
3+4
3+4
3+4
1+2+3+4
1+2+3+4
1+2+3+4
1+2+3+4
To select an Audio Summing mode:
Adjusting Gain for Summed Outputs
1. Menu: DEVICE UTILITIES > AUDIO SUMMING
Use the gain controls for each channel to create the overall mix balance.
The front panel LEDs indicate the audio level for each channel. If an
overload occurs, the red LEDs will illuminate indicating that the internal
limiter is active and the display will show an overload message. To correct,
adjust the overall gain balance.
2. Use the control wheel to select an option, and then press Enter.
Note: When set to OFF, Audio Summing is disabled.
11
Firmware
Firmware is embedded software in each component that controls functionality. Periodically, new versions of firmware are developed to incorporate additional
features and enhancements. To take advantage of design improvements, new versions of the firmware can be uploaded and installed using the Firmware
Update Manager tool available in Shure's Wireless Workbench® 6 (WWB6) software. Software is available for download from http://www.shure.com/wwb.
Firmware Versioning
When updating receiver firmware, update transmitters to the same firmware version to ensure consistent operation.
The firmware of all ULX-D devices has the form of MAJOR.MINOR.PATCH (e.g., 1.2.14). At a minimum, all ULX-D devices on the network (including
transmitters), must have the same MAJOR and MINOR firmware version numbers (e.g., 1.2.x).
Updating the Receiver
CAUTION! Ensure that receiver power and network connections are maintained during a firmware update. Do not turn off the receiver until the update is
complete.
Once the download is complete, the receiver automatically begins the firmware update, which overwrites the existing firmware.
1. From Shure Wireless Workbench software, open the Firmware Update Manager: Tools > Firmware Update Manager.
2. Click Check Now to view new versions available for download.
3. Select the updates and click download.
4. Connect the receiver and computer to the same network.
5. Download the latest firmware to the receiver.
Updating the Transmitter
1. To upload the firmware to the transmitter, go to DEVICE UTILITIES > TX FW UPDATE on the receiver.
2. Place the transmitter on its side and align the IR ports.
3. Press ENTER on the receiver to begin the download to the transmitter. IR ports must be aligned for the entire download, which can take 50 seconds or
longer.
Transmitter Presets
Use the TX SYNC SETUP menu to configure transmitter settings on the
receiver to transfer to the transmitter during a sync. Each parameter has the
default value KEEP, which leaves that setting unaffected by a sync.
Feature
Setting
BP PAD
0 dB, -12 dB
LOCK
Power, Menu, All, None
RF POWER
10mW=Nm, 1mW=Lo, 20mW=Hi
BATT
Alkaline, NiMH, Lithium
BP OFFSET
0 dB to +21 dB (in 3 dB increments)
HH OFFSET
0 dB to +21 dB (in 3 dB increments)
Cust. Group
OFF, ON
Note: When Cust. Group is set to ON, it may take up to 30 seconds to
complete an IR sync. Select OFF if Custom Groups are not in use for
faster IR sync.
12
Creating a System Preset
System Presets allow a current receiver setup to be saved and restored.
Presets store all receiver settings to provide a quick way to configure a
receiver or switch between several different setups. Up to 4 presets can be
stored in receiver memory.
To save the current receiver setup as a new preset: DEVICE UTILITIES >
SYSTEM RESET > SAVE > CREATE NEW PRESET
Use the control wheel to name the preset, and then press Enter to save.
To recall a saved preset: DEVICE UTILITIES > SYSTEM RESET > RESTORE
Use the control wheel to select the preset name, and then press Enter.
Locking Controls and Settings
Use the LOCK feature to prevent accidental or unauthorized changes to the
hardware.
Receiver
Custom Groups
Use this feature to create and export up to 6 groups of manually selected
frequencies to networked receivers prior to a group scan to simplify system
set up.
Menu path: DEVICE UTILITIES > LOCK
Tip: Use Wireless Workbench or Wireless Frequency Finder to select the
best compatible frequencies. See www.shure.com for more information.
Use the control wheel to select and lock any of the following receiver
functions.
To create a custom group: DEVICE UTILITIES > ADVANCED RF > CUSTOM
GROUPS > SETUP
• MENU: All menu paths are inaccessible
Use the control wheel to choose group, channel and frequency values.
Press ENTER to save.
• POWER: Power switch is disabled
Prior to performing a group scan, export a custom group to networked
receivers:
• GAIN: Gain adjustment is locked
• SCN/SYC: Cannot perform a Scan and Sync
Tip: To unlock, press the EXIT button, turn the control wheel to select
UNLOCKED, and then press ENTER to save.
Transmitter
Menu path: UTILITY > LOCK
Use the transmitter controls to select and lock any of the following
transmitter functions.
• MENU LOCK: All menu paths are inaccessible.
• POWER LOCK: Power switch is disabled
Quick-Lock Option: To turn on the transmitter with its power and menu
navigation buttons locked, press and hold the ▲ button during power-on until
the locked message is displayed.
Tip: To unlock the MENU LOCK, press the ENTER button 4 times to pass
through the following screens: UTILITY > LOCK > MENU UNLOCK
1. Go to DEVICE UTILITIES > ADVANCED RF > CUSTOM GROUPS > EXPORT
2. Press the flashing ENTER button to export all custom groups to all
receivers on the network.
Note: Use the CLEAR ALL option to remove all custom group settings.
System Reset
System Reset clears the current receiver settings and restores the factory
default settings.
To restore factory default settings:
1. Go to DEVICE UTILITIES > SYSTEM RESET > RESTORE.
2. Scroll to the DEFAULT SETTINGS option and press ENTER.
3. Press the flashing ENTER button to return the receiver to the default
settings.
To unlock the POWER LOCK, set the power switch to the off position, then
press and hold the ▲ button while resetting the power switch to the on
position.
RF Cascade Ports
Encryption
ULX-D features Advanced Encryption Standard (AES-256) to ensure that
only the receiver that is keyed to the transmitter can monitor the audio
content.
The receiver has 2 RF cascade ports on the rear panel to share the signal
from the antennas with 1 additional receiver.
Use a shielded coaxial cable to connect the RF cascade ports from the first
receiver to the antenna inputs of the second receiver.
Important! The frequency band must be the same for both receivers.
Note: When enabled, encryption is applied to all receiver channels.
Encryption does not affect Dante audio signals, audio quality, or channel
spacing.
1. Enable encryption on the receiver: DEVICE UTILITIES > ENCRYPTION.
The encryption symbol illuminates and the LCD displays SYNC NOW FOR
ENCRYPTION.
2. Sync the transmitter to the receiver. The encryption symbol displays on
the transmitter.
Note: Any change to the encryption status on the receiver such as enabling/
disabling encryption or requesting a new encryption key, requires a sync
to send the settings to the transmitter. ENCRYPTION MISMATCH warning
will display on the receiver LCD panel if the transmitter and receiver do not
share the same encryption key.
Antenna Bias
Antenna ports A and B provide a DC bias to power active antennas. Set the
DC power to off when using passive (non-powered) antennas.
To turn bias off: DEVICE UTILITIES > ADVANCED RF > ANTENNA BIAS > OFF
13
Receiver Menu Descriptions
Channel Home Screen
RADIO
Displays Group, Channel, Frequency, and
TV information. Use the control wheel to edit
values
RADIO
G:
CH:
FREQUENCY
TV
AUDIO
GAIN
EDIT NAME
G:
Group for the selected frequency
CH:
Channel for the selected frequency
FREQUENCY
Selected frequency (MHz)
TV:
Displays the TV channel for the selected
frequency
AUDIO
TX SYNC SETUP
BP PAD
LOCK
RF POWER
BATT
GAIN
Use the control wheel or gain buttons to adjust
the channel gain from -18 to 42 dB, in 1 dB
increments.
EDIT NAME
Use the control wheel to assign and edit the
selected receiver channel name.
BP OFFSET
HH OFFSET
Cust. Group
BATTERY INFO
HEALTH
CHARGE
CYCLES
TEMP
DEVICE ULTILITES
FREQUENCY DIVERSITY
AUDIO SUMMING
ENCRYPTION
ADVANCED RF
LOCK
HOME INFO
DISPLAY
NETWORK
TX FW UPDATE
14
TX SYNC SETUP
BP PAD
Sets the audio input attenuation options: KEEP,
0, -12.
LOCK
Sets the lock options: KEEP, Power, Menu, All,
None
RF POWER
Sets the transmitter RF power level: KEEP,
10mW=Nm, 1mW=Lo, 20mW=Hi.
BATT
Sets the transmitter battery type to ensure
accurate metering: KEEP, Alkaline, NiMH,
Lithium
BP OFFSET
Adjustable gain to compensate for signal level
difference between transmitters: KEEP, 0 to 21
dB in 3 dB increments
HH OFFSET
Adjustable gain to compensate for signal level
difference between transmitters: KEEP, 0 to 21
dB in 3 dB increments
Cust. Group
Create Custom Groups of up to 6 frequencies
and export to networked receivers
BATTERY INFO
HEALTH
Percentage of charge capacity compared to a
new battery
CHARGE
Percentage of charge capacity
SYSTEM RESET
CYCLES
Number of charge cycles logged by the battery
VERSION
TEMP
Battery temperature: °C/°F
DEVICE UTILITIES
FREQ DIVERSITY
•
•
•
•
OFF (default)
1+2
3 + 4 (quad only)
1 + 2 / 3 + 4 (quad only)
AUDIO SUMMING
•
•
•
•
•
OFF (default)
1+2
3 + 4 (quad only)
1 + 2 / 3 + 4 (quad only)
1 + 2 + 3 + 4 (quad only)
ENCRYPTION
Set encryption: ON/OFF
ADVANCED RF
•
•
•
•
HIGH DENSITY: ON/OFF
CUSTOM GROUPS: SETUP/EXPORT/CLEAR
ANTENNA BIAS: ON/OFF
SWITCH BAND (Japan AB band only)
LOCK
•
•
•
•
MENU: LOCKED/UNLOCKED
GAIN: LOCKED/UNLOCKED
POWER: LOCKED/UNLOCKED
SCN/SYC: LOCKED/UNLOCKED
HOME INFO
Select screen options for Home Menu.
DISPLAY
• CONTRAST
• BRIGHTNESS: LOW/MEDIUM/HIGH
NETWORK
• CONFIGURATION: SWITCHED/REDUNDANT
AUDIO/SPLIT
• SHURE CONTROL: DEVICE ID, Network Mode,
Set IP and Subnet values for Ethernet network
• DANTE: DANTE DEVICE ID, AUDIO & CNTRL,
REDUNDANT AUDIO, Set IP and Subnet values
for Dante™ network
Note: Additional information can be
accessed from the selected networking
option.
TX FW UPDATE
IR DOWNLOAD, Tx Firmware Version
SYSTEM RESET
• RESTORE: Default Settings, Presets
• SAVE: Create New Preset
• DELETE: Delete Preset
VERSION
•
•
•
•
•
•
•
Model
Band
S/N (serial number)
Ver
Mcu
FPGA
Boot
Networking ULX-D Receivers
ULX-D Dual and Quad receivers feature a Dante dual-port network interface. Dante technology provides an integrated solution to distribute digital audio,
manage control signals, and carry Shure Control (WWB and AMX/Crestron) signals. Dante uses standard IP over Ethernet and safely coexists on the same
network as IT and control data. Selectable Dante networking modes route port signals for flexible network set up.
Network Control Software
The ULX-D receivers can be controlled by Shure Control (WWB6) for remote management and monitoring and the Dante Controller to manage digital audio
routing. Signals for AMX and Crestron controllers are carried on the same network as Shure Control.
Shure Control
Dante
Wireless Workbench 6 (WWB6) software provides comprehensive
control for wireless audio systems. Wireless Workbench enables live
remote adjustments to networked receivers for real-time changes to gain,
frequency, RF power, and control locks. A familiar channel strip interface
displays audio meters, transmitter parameters, frequency settings and
network status.
The Dante controller is a free software program created by Audinate™
to configure and manage a network of Dante enabled devices. Use the
controller to create audio routes between networked components and to
monitor the status of online devices.
Visit www.audinate.com for download and installation instructions.
Wireless Workbench 6 is available for Windows or Mac and can be
downloaded at: www.shure.com/wwb
IP Address Configuration
An IP address must be assigned to each device in the network to ensure communication and control between components. Valid IP addresses can assigned
automatically using a DHCP server or manually from a list of valid IP addresses. If using Dante audio, a separate Dante IP address must also be assigned to
the receiver.
Automatic IP Addressing
Manual IP Addressing
1. If using a DHCP capable Ethernet switch, set the DHCP switch to ON.
1. Connect the receivers to an Ethernet switch.
2. Set the IP Mode to Automatic for all receivers: DEVICE UTILITIES >
NETWORK > SHURE CONTROL > NETWORK
2. Set the IP Mode to Manual for all devices: DEVICE UTILITIES > NETWORK
> SHURE CONTROL > NETWORK
3. Use the control wheel to set the mode to Automatic, press ENTER to save.
3. Use the control wheel to set the mode to Manual.
Note: Use only one DHCP server per network.
4. Set valid IP addresses and subnet values for all devices, press ENTER to
save.
ON
OFF
DHCP
Dante IP Addressing
IP addresses for a Dante network can assigned automatically using a DHCP
server or manually from a list of valid IP addresses
control
ULXD4
Digital Wireless Receiver
RX1
RF audio
A B
gain
RX2
RF audio
A B
gain
RX3
OL
OL
ENTER
OL
RF audio
A B
gain
RX4
OL
RF audio
A B
gain
power
gain
power
gain
power
OL
OL
OL
OL
EXIT
SCAN
push
control
ULXD4
Digital Wireless Receiver
RX1
RF audio
A B
gain
RX2
RF audio
A B
gain
RX3
OL
OL
ENTER
OL
RF audio
A B
gain
RX4
OL
RF audio
A B
OL
OL
OL
OL
EXIT
SCAN
push
control
ULXD4
Digital Wireless Receiver
RX1
RF audio
A B
OL
ENTER
OL
gain
RX2
RF audio
A B
OL
OL
gain
RX3
RF audio
A B
OL
OL
gain
RX4
RF audio
A B
To select the Dante IP addressing mode (Automatic or Manual): DEVICE
UTILITIES > NETWORK > DANTE > AUDIO & CNTRL
Use the control wheel to select the mode, and then press ENTER to save.
OL
OL
EXIT
SCAN
push
Networking Acronyms
DHCP: Dynamic Host Configuration Protocol
LAN: Local Area Network
MCU: Micro Controller Unit
RJ45: Ethernet Connection
RX: Receiver
TX: Transmitter
WWB6: Wireless Workbench 6 Software
VLAN: Virtual Local Area Network
MAC: Machine Access Code
15
Overview of Dante Network Modes
The Dante network interface has two ports (Primary and Secondary) to provide flexible routing and configuration options for network signals.
Three selectable Dante network modes are available to control signal routing from the receiver ports to the Dante network.
Network Mode
Port Function and Signals
Secondary
Primary
SWITCHED
Shure Control
Dante Audio and Control
Shure Control
Dante Audio and Control
REDUNDANT AUDIO
Dante Redundant Audio
Shure Control
Dante Audio and Control
SPLIT
Dante Audio and Control
Shure Control
Application
For single network Installations of star or daisy-chained
networks.
Primary and Secondary ports are configured are 2 separate
networks. The Secondary port carries a backup copy of the
Primary digital audio signal.
Primary and Secondary ports are configured are 2 separate
networks to provide isolation between control signals and
audio signals.
Setting the Dante Networking Mode
Select a Dante mode to configure network signal routing on the Primary and Secondary ports.
Set all receivers on the network to the same mode.
Note: Remove network connections from the receiver before changing the mode.
1. From the receiver menu: DEVICE UTILITIES > NETWORK > CONFIGURATION
2. Use the control wheel to select a mode (SWITCHED, REDUNDANT AUDIO, SPLIT)
3. Press ENTER to save.
4. Cycle receiver power to enable the mode change.
16
CONFIGURATION
SWITCHED (default)
Network Connection and Configuration Examples
Note: Use shielded Cat5e cable for network connections to ensure reliable performance.
Switched Mode
Switched mode is typically used for single network installations of star or
daisy-chained networks. Switched mode is recommended for installations
that don't require Dante audio.
Network Characteristics:
• Dante Audio and Shure Control are present on both the Primary and
Secondary ports
• The Dante IP address and the Shure Control IP address must be on the
same subnet. The computer running WWB6 must also be on this subnet.
Network Example (Dante Audio + WWB6)
① Computer
Connect the computer running the Dante controller and WWB6 to the Primary
port.
①
② DHCP Server
②
Can be configured with or without a DHCP server. Do not route audio through
the server.
③ Gigabit Ethernet Switch
• Do not connect both network ports to the same Ethernet switch
• Use a star network topology to minimize audio latency
④ Receiver Connection
Note: Dante controller
(AXT620, Wi-Fi router, etc...)
③
does not support Wi-Fi
network connections.
Connect receivers to the Primary port
⑤ Dante Receiver
Connect Dante receivers (mixers, recorders, amplifiers) to the Primary port.
(mixers, recorders,
amplifiers, etc...)
④
⑤
Network Example (WWB6 Only)
① Computer
Connect the computer running WWB6 to the Primary port.
② DHCP Server
①
Can be configured with or without a DHCP server.
③ Receiver Connection
②
(AXT620, Wi-Fi router, etc...)
Connect receivers to the Primary port
③
17
Redundant Audio Mode
Use Redundant mode to carry a backup copy of the Dante audio on the
Secondary network in case the audio on the primary network is interrupted.
Network Characteristics:
• Dante Primary Audio and Shure Control are present on the Primary port
• Backup Dante audio is present on the Secondary port
• The Primary Dante IP address and the Shure Control IP address must be
on the same subnet. The computer running WWB6 must also be on this
subnet.
• The Secondary Dante IP Address must be set to a different subnet
Note: Devices connected to the Redundant network must be compatible
with Redundant audio.
Network Example
① Computer
Connect the computer running the Dante controller and
WWB6 to the Primary port.
② DHCP Server
①
Can be configured with or without a DHCP server. Do
not route audio through the server.
③ Gigabit Ethernet Switches
• Use dedicated switches for the Primary and Secondary
networks
• Do not connect both network ports to the same
Ethernet switch
• Use a star network topology to minimize audio latency
④ Receiver Connection
Connect Primary and Secondary ports to dedicated
switches.
②
Note: Dante controller does not
support Wi-Fi network connections.
③
④
Note: The Secondary port only supports manual IP
or automatic Link-Local configuration. The Link-Local
Dante Secondary address subnet is preset to 172.31.x.x
(255.255.0.0)
⑤ Dante Receiver
Connect Dante receivers (mixers, recorders, amplifiers)
to the Primary or Secondary ports.
(mixers, recorders,
amplifiers, etc...)
18
(AXT620, Wi-Fi router, etc...)
⑤
③
Split Mode
Use Split Mode to isolate control signals from audio signals by placing
them on two separate networks.
Network Characteristics:
• Shure Control is present on the Primary port
• Dante Audio is present on the Secondary port
• The IP addresses for Dante and Shure Control must be on different
subnets
Network Example
① Computer (Dante Controller)
Connect the computer running the Dante controller
to the Secondary port.
② DHCP Server (Secondary Network)
Can be configured with or without a DHCP server.
Do not route audio through the server.
③ Gigabit Ethernet Switch
(Secondary Network)
• Use dedicated switches for the Primary and
Secondary networks
• Do not connect both network ports to the same
Ethernet switch
• Use a star network topology to minimize audio
latency
Note: Dante controller does not
support Wi-Fi network connections.
①
②
(AXT620, Wi-Fi router, etc...)
③
(AXT620, Wi-Fi router, etc...)
⑧
④
④ Receiver Connections (Dante Audio)
Connect the Secondary ports to the Secondary
network switch.
⑤
⑥
⑦
⑤ Computer (Shure Control)
Connect the computer running the Shure Control to
the Primary port.
⑥ DHCP Server (Primary Network)
Can be configured with or without a DHCP server.
Do not route audio through the server.
⑦ Gigabit Ethernet Switch
(Primary Network)
• Use dedicated switches for the Primary and
Secondary networks
• Do not connect both network ports to the same
Ethernet switch
• Use a star network topology to minimize audio
latency
(mixers, recorders,
amplifiers, etc...)
⑨
⑧ Receiver Connections
(Shure Control)
Connect the Primary ports to the Primary network
switch.
⑨ Dante Receiver
Connect Dante receivers (mixers, recorders,
amplifiers) to the Primary port.
19
Assigning Network Device IDs for Shure Control and Dante Control
When using the receiver in a network with Shure Control (WWB6) and a Dante Controller, two Device IDs are required: one for Shure Control and one for
Dante Control. Device IDs are used to identify devices on the network and for creating Dante digital audio routes.
Best Practices
Using the following best practices will help to organize network setup and ease troubleshooting.
• For consistency, convenience, and easy troubleshooting, use the same device ID for both WWB6 (Shure Control) and for the Dante network.
• The Dante network requires unique Dante device IDs to prevent a loss of audio signal routing. Any duplicate IDs on the network will be tagged with a
number such as -1, -2, -3, etc.... and must be changed to a unique value.
• WWB6 (Shure Control) does not require unique device IDs and duplicates do not affect the Dante network; however, a best practice is to use unique
device IDs.
Setting the Shure Control Device ID
Viewing Dante Device IDs in the Dante Controller
Dante device IDs are displayed in the Network View window in the Dante
Controller.
1. Launch WWB6.
2. Open the Inventory
View.
1. Launch the Dante controller and open the Network View window.
2. Verify that the Dante device IDs match the IDs entered in the receiver.
3. Click on the Device ID
to enable editing.
Tip: Click on the device
icon next to the channel
name to identify the
receiver using the Flash
function.
Optionally, the Shure Control Device ID can be entered from the receiver
front panel:
1. From the receiver menu: DEVICE UTILITIES > NETWORK > SHURE
CONTROL > Dev. ID
2. Use the control wheel to edit the ID.
3. Press ENTER to save.
Setting the Dante Device ID
The Dante ID can be set from the ULXD receiver menu or from the Dante
controller.
Note: Changing the Dante ID will cause a loss of audio signal. After an
ID has been changed, use the Dante controller to restore audio route
subscriptions using the new ID.
From the receiver menu:
1. DEVICE UTILITIES > NETWORK >
DANTE > Dev. ID
DANTE DEVICE ID
ULXD-RX1
2. Use the control wheel to enter a
unique ID.
3. Press ENTER to save.
From the Dante controller:
1. Open the Device View and select the receiver from the pulldown menu.
2. Click on the Device Config tab.
3. Enter the ID in the Rename Device box and press ENTER.
20
Identify Device Feature
The Dante controller's Identify Device feature flashes the front panel LEDs
of a selected receiver to provide identification when multiple receivers are
in use.
Open the Device View in the Dante controller and click on the identify icon
(eye). The front panel LEDs of the selected receiver will respond by flashing.
Configuring Audio Routes with the Dante Controller
Devices that appear in the Dante controller are categorized as "Transmitters" and "Receivers"
In order for audio to flow in the network, audio routes (subscriptions) must be configured between transmitters and receivers.
Note: ULX-D receivers will appear in the Dante controller as a Transmitter. Devices that have both inputs and outputs commonly appear as both transmitters
and receivers.
Dante Transmitters
Dante Receivers
Devices that send or add audio into the network such as:
Devices that receive audio from the network such as:
• Receiver Outputs
• Amplifier Inputs
• Mixer Outputs
• Signal Processor Inputs
• Amplifier Outputs
• Mixer Inputs
• Signal Processor Outputs
• Recorder Inputs
• Recorder Playback Outputs
Forming an Audio Route
Launch the Dante Controller and click on the intersection point between components to form an audio route. The audio route is also referred to as a
Subscription.
1. Find the intersection between the transmitter and receiver channels.
2. Click on the
where the components meet.
3. A green checkmark

indicates that the audio route has been established.
4. Check the audio to verify that the audio route has been formed.
For additional information about the Dante controller, visit www.audinate.com.
Click to expand this Dante device
to view its Tx channels
Enter text to show only those
Dante devices and channels
containing that text
Click to expand all Dante
devices and view all Rx
channels
Click while holding the Ctrl
key to subscribe to all possible
channels at the same time.
Click to collapse the Dante
device Rx channel view
Click to expand all Dante device
and view all Tx channels
21
Restoring Dante Factory Settings
The receiver and the Dante network card can be reset to restore factory Dante settings. Performing a reset is helpful for clearing existing data before setting
up a system.
Caution! Performing a reset on either the Dante network card or on the ULX-D receiver will interrupt the Dante audio.
Tip: Prior to performing a factory reset, note the current Dante network mode and IP settings. After a reset, the Dante network mode reverts to SWITCHED,
and the IP address mode revert to AUTO.
Restoring Receiver and Dante Card Factory Settings
Restoring the Dante Network Card Factory Settings
Performing a reset from the receiver restores the factory settings and
configures the Shure Control and Dante IP address mode to AUTO.
The Factory Reset option within the Dante controller restores the Dante card
to the factory settings and configures the Dante IP address mode to AUTO.
1. From the receiver menu: DEVICE UTILITIES > SYSTEM RESET > RESTORE
1. From the Dante controller, select a receiver and open the Network Config
tab.
2. Press ENTER to complete the reset.
2. Click on Factory Reset.
DEFAULT SETTINGS
RESTORE
DEFAULT SETTINGS
RESTORE DEFAULTS
OVERWRITE CURRENT
SETTINGS WITH
DEFAULT SETTINGS?
3. Allow the Dante controller to refresh before making any additional
changes.
Connecting to an AMX or Crestron System
The ULX-D receiver connects to an AMX or Crestron control system via the Ethernet, using on the same cables used to carry Shure Control (WWB6). Use
only one controller per system to avoid messaging conflicts.
• Connection: Ethernet (TCP/IP; ULX-D receiver is the client)
• Port: 2202
For a comprehensive list of ULX-D command strings, visit: http://shure.custhelp.com/app/answers/detail/a_id/4976
Network Troubleshooting
• Use only one DHCP server per network
• All devices must share the same subnet mask
• All receivers must have the same level of firmware revision installed
• Look for the illuminated network icon on the front panel of each device:
If the icon is not illuminated, check the cable connection and the LEDs on the network jack.
If the LEDs are not on and the cable is plugged in, replace the cable and recheck the LEDs and network icon.
To check connectivity of WWB6 to the network:
1. Start WWB6 software and use Inventory view to see devices connected to the network.
2. If not, find the IP address from one of the devices on the network (such as a ULX-D receiver) and see if you can ping it from the computer running WWB6.
3. From a WINDOWS/MAC command prompt, type ‘ping IPADDRESS’ of the device (e.g. "ping 192.168.1.100").
4. If the ping returns success (no packet loss), then the computer can see the device on the network. If the ping returns failure (100% packet loss), then check
the IP address of the computer to ensure it’s on the same subnet.
5. If the pings are successful and the devices still do not show up in the WWB6 inventory, check to ensure all firewalls are either disabled or allow the WWB
network traffic to pass to the application. Check that firewall settings are not blocking network access.
22
Managing the ULXD Receiver with Wireless Workbench 6
Adding a computer running Wireless Workbench® 6 to the network allows for remote control and monitoring of the receiver.
Visit: www.shure.com/wwb to download Wireless Workbench 6 software.
Viewing the Receiver in WWB6 Inventory
Click on the Inventory tab to view the receiver channels.
Double-click on parameters to enable editing.
Tip: Clicking on the receiver Icon next to the Model flashes
the front panel LEDs for remote identification.
Managing and Monitoring Receiver Settings
Manage and monitor receiver settings by opening the Monitor tab in Wireless Workbench. Click on the Settings button to show or hide the full Properties
window.
1. Click on the Monitor tab to view the Device Chooser.
2. From the Device Chooser, click on a channel to select.
3. Click on Properties to open the Properties window.
① RF and Audio Meters
Displays: current levels, band, TV, and TX Overload
② Transmitter Settings
Displays: RF Power, Tx Type, Tx Offset, Tx Lock
③ Frequency Settings
Use drop-down to edit value
④ Encryption Icon
Illuminates when Encryption is enabled
⑤ Receiver Output Mute
Click on the mute button to enable mute
⑥ Receiver Gain Setting
Use drop-down to edit value
⑦ Custom Groups
Click to enter custom group settings
⑧ IR Presets
Click to configure transmitter IR presets
10
⑨ Utilities Tab
Accesses Utility settings
⑩ Network Tab
Set network mode, view: IP address, Subnet, MAC,
Firmware version
11
15
⑪ Advanced RF Settings
Enable High Density mode or Antenna Bias
⑫ Encryption
Enable/Disable Encryption
⑬ Frequency Diversity Mode
12
13
Enable and Select Frequency Diversity mode
⑭ Audio Summing
Enable and Select Audio Summing mode
14
⑮ Locks
Lock/Unlock: Menu, Gain, Power, Scan/Sync
Locking the Audio Source in Frequency Diversity Mode
WWB6 software offers an option to selectively lock the Frequency Diversity audio source to a specific transmitter.
Lock the audio source to select the best audio if a problem develops with one of the channels.
1. Open the monitoring tab.
2. Under FD Audio Source, click on "Lock to" option to select a transmitter as the audio source.
To restore Frequency Diversity switching, click on the Auto Switch option.
23
Troubleshooting
Issue
See Solution...
No Sound
Power, Cables, Radio Frequency, or Encryption Mismatch
Faint sound or distortion
Gain
Lack of range, unwanted noise bursts, or dropouts
RF
Cannot turn transmitter off or change frequency settings, or can't program
receiver
Interface locks
Encryption Mismatch message
Encryption Mismatch
Firmware Mismatch message
Firmware Mismatch
Antenna Fault message
RF
Power
Make sure that the receiver and transmitter are receiving sufficient voltage.
Check the battery indicators and replace the transmitter batteries if
necessary.
Gain
Adjust the system gain on the front of the receiver. Ensure the output level
(XLR output only) on the back of the receiver corresponds to the input of the
mixing console, amplifier, or DSP.
Cables
Check that all cables and connectors are working correctly.
Interface Locks
The transmitter and the receiver can be locked to prevent accidental or
unauthorized changes. A locked feature or button will produce the Locked
screen on the LCD panel.
Encryption Mismatch
Re-sync all receivers and transmitters after enabling or disabling encryption.
Firmware Mismatch
Reducing Interference
• Perform a group or channel scan to find the best open frequency.
Perform a sync to transfer the setting to the transmitter.
• For multiple systems, check that all systems are set to channels in the
same group (systems in different bands do not need to be set to the
same group).
• Maintain a line of sight between transmitter and receiver antennas.
• Move receiver antennas away from metal objects or other sources of
RF interference (such as CD players, computers, digital effects, network
switches, network cables and Personal Stereo Monitor (PSM) wireless
systems).
• Eliminate RF overload (see below).
Increasing Range
If the transmitter is more than 6 to 60 m (20 to 200 ft) from the receiver
antenna, you may be able to increase range by doing one of the following:
• Reduce interference (see above).
• Increase transmitter RF power level.
• Use Normal mode instead of High Density mode.
• Use an active directional antenna, antenna distribution system, or other
antenna accessory to increase RF range.
Eliminating RF Overload
If you see the red RF LED on a receiver, try the following:
Paired transmitters and receivers must have the same firmware version
installed to ensure consistent operation. See Firmware topic for firmware
update procedure.
• Reduce the transmitter RF power level
Radio Frequency (RF)
• Use omnidirectional antennas
RF LEDs
If neither blue RF Diversity LED is illuminated, then the receiver is not
detecting the presence of a transmitter.
The amber RF Signal Strength LEDs indicate the amount of RF power being
received. This signal could be from the transmitter, or it could be from an
interfering source, such as a television broadcast. If more than one or
two of the amber RF LEDs are still illuminated while the transmitter is off,
then that channel has too much interference, and you should try a different
channel.
The red RF LED indicates RF overload. This will usually not cause a
problem unless you are using more than one system at the same time, in
which case, it can cause interference in the other system.
Compatibility
• Perform a Scan and Sync to ensure the transmitter and receiver are set
to the same group and channel.
• Look at the label on the transmitter and receiver to make sure they are in
the same band (G50, J50, L50, etc...).
24
• Move the transmitter further away from the receiver—at least 6 m (20 ft)
• If you are using active antennas, reduce antenna or amplifier gain.
Antenna Faults
The Antenna Fault message indicates a short circuit condition at an antenna
port.
• Check antennas and cables for damage
• Ensure that antenna ports are not overloaded
• Check antenna bias voltage setting. Turn off voltage if using passive
antennas.
ULX-D Specifications
RF Carrier Frequency Range
470–932 MHz, varies by region (See Frequency Range and Ouput Power
table)
Working Range
100 m (330 ft)
Note: Actual range depends on RF signal absorption, reflection and interference.
RF Tuning Step Size
25 kHz, varies by region
Image Rejection
>70 dB, typical
RF Sensitivity
−98 dBm at 10-5 BER
Latency
<2.9 ms
Audio Frequency Response
ULXD1
20 – 20 kHz (±1 dB)
ULXD2
Note: Dependent on microphone type
Audio Dynamic Range
A-weighted, typical, System Gain @ +10
XLR Analog Output
>120 dB
Dante Digital Output
130 dB
Total Harmonic Distortion
−12 dBFS input, System Gain @ +10
<0.1%
System Audio Polarity
Positive pressure on microphone diaphragm produces positive voltage on
pin 2 (with respect to pin 3 of XLR output) and the tip of the 6.35 mm (1/4inch) output.
Operating Temperature Range
-18°C (0°F) to 50°C (122°F)
Note: Battery characteristics may limit this range.
Storage Temperature Range
-29°C (-20°F) to 74°C (165°F)
Note: Battery characteristics may limit this range.
ULXD4D & ULXD4Q
Audio Output
Dimensions
44 x 482 x 274 mmH x W x D
Gain Adjustment Range
−18 to +42 dB in 1 dB steps (plus Mute setting)
Weight
ULXD4D
3.36 kg (7.4 lbs), without antennas
ULXD4Q
3.45 kg (7.6 lbs), without antennas
Housing
steel; Extruded Aluminum
ULXD4 Power Requirements
ULXD4D
100 to 240 V AC, 50-60 Hz, 0.26 A max.
ULXD4Q
100 to 240 V AC, 50-60 Hz, 0.32 A max.
RF Input
Spurious Rejection
>80 dB, typical
Connector Type
BNC
Impedance
50 Ω
Bias Voltage
12 to 13 V DC, 150 mA maximum, per antenna
switchable on/off
Configuration
XLR
balanced (1=ground, 2=audio +, 3=audio −)
Impedance
100 Ω
Full Scale Output
LINE setting
+18 dBV
MIC setting
−12 dBV
Mic/Line Switch
30 dB pad
Phantom Power Protection
Yes
Networking
Network Interface
Dual Port Ethernet 10/100 Mbps, 1Gbps, Dante Digital Audio
Network Addressing Capability
DHCP or Manual IP address
Maximum Cable Length
100 m (328 ft)
Cascade Output
Connector Type
BNC
Note: For connection of one additional receiver in the same band
Configuration
Unbalanced, passive
Impedance
50 Ω
Insertion Loss
0 dB
25
ULXD1
MIc Offset Range
0 to 21 dB (in 3 dB steps)
Battery Type
Shure SB900 Rechargeable Li-Ion or LR6 AA batteries 1.5 V
Battery Runtime
@ 10 mW
Shure
SB900
>11 hours
alkaline
11 hours
See Battery Runtime Chart
Dimensions
86 mm x 66 mm x 23 mm (3.4 in. x 2.6 in. x 0.9 in.) H x W x D
Weight
142 g (5.0 oz.), without batteries
Housing
Cast aluminum
Audio Input
Connector
4-Pin male mini connector (TA4M), See drawing for details
Configuration
Unbalanced
Impedance
1 MΩ, See drawing for details
Maximum Input Level
1 kHz at 1% THD
Pad Off
8.5 dBV (7.5 Vpp)
Pad On
20.5 dBV (30 Vpp)
Preamplifier Equivalent Input Noise (EIN)
System Gain Setting ≥ +20
-120 dBV, A-weighted, typical
RF Output
Connector
SMA
ULXD2
Mic Offset Range
0 to 21 dB (in 3 dB steps)
Battery Type
Shure SB900 Rechargeable Li-Ion or LR6 AA batteries 1.5 V
Battery Runtime
@ 10 mW
Shure
SB900
>11 hours
alkaline
11 hours
See Battery Runtime Chart
Dimensions
256 mm x 51 mm (10.1 in. x 2.0 in.) L x Dia.
Weight
340 g (12.0 oz.), without batteries
Housing
Machined aluminum
Audio Input
Configuration
Unbalanced
Maximum Input Level
1 kHz at 1% THD
145 dB SPL (SM58), typical
Note: Dependent on microphone type
RF Output
Antenna Type
Integrated Single Band Helical
Occupied Bandwidth
<200 kHz
Modulation Type
Shure proprietary digital
Power
1 mW, 10 mW, 20 mW
See Frequency Range and Ouput Power table, varies by region
Antenna Type
1/4 wave
Impedance
50 Ω
Occupied Bandwidth
<200 kHz
Modulation Type
Shure proprietary digital
Power
1 mW, 10 mW, 20 mW
See Frequency Range and Ouput Power table, varies by region
26
Battery Runtime
Battery Type
1 mW
10 mW
20 mW
SB900
>11 hours
>11 hours
>7 hours
Alkaline
<11 hours
<11 hours
<5.5 hours
NiMH
<11 hours
<11 hours
<8 hours
Li-primary
12.5-18 hours
12.5-18 hours
9.5-12 hours
The values in this table are typical of fresh, high quality batteries. Battery
runtime varies depending on the manufacturer and age of the battery.
Tables and Diagrams
TA4M Connector
500 Ω
1µF
910k Ω
5 V DC
500 Ω
Active
Load
100 µF
440 pF
Pad
12dB
Audio Input
① Ground
② Bias Voltage
③ Audio Input
Ground
④ Active Load
XLR Receiver Output
50 Ω
22 µF
-30 dB
50 Ω
22 µF
mic/ line
XLR to ¼ Output
Use the following wiring diagram to convert the XLR output to a ¼ output.
N/C
* No Connection
Frequency Range and Transmitter Output Power
Band
Frequency Range ( MHz)
Power (mW)
Band
Frequency Range ( MHz)
Power (mW)
G50
470 to 534
1/10/20
L51
632 to 696
1/10/20
G51
470 to 534
1/10/20
P51
710 to 782
1/10/20
G52
479 to 534
1/10
R51
800 to 810
1/10/20
H50
534 to 598
1/10/20
JB (Tx only)
806 to 810
1/10
H51
534 to 598
1/10/20
H52
534 to 565
1/10
J50
572 to 636
1/10/20
K51
606 to 670
1/10
L50
632 to 696
1/10/20
"A" band (770.250805.750): 1/10/20
AB (Rx and Tx)
770 to 810
"B" band (806.125809.750): 1/10
Q51
794 to 806
1/10/20
X50
925 to 932
1/10
27
Furnished Accessories
All Systems
Bodypack System
Receiver
ULXD4D (Dual Receiver),
ULXD4Q (Quad Receiver)
Bodypack Transmitter
ULXD1
1/2-Wave Antenna (2)
Varies by band (see Antennas
table for band-specific part
numbers)
1/4-Wave Antenna
Varies by band (see Antennas
table for band-specific part
numbers)
Hardware Kit (1)
90XN1371
Zipper Bag
95A2313
2' BNC Cable (2)
95K2035
AA Alkaline batteries (2)
80B8201
BNC Bulkhead Adapters (2)
95A8994
3' Ethernet Cable (1)
95B15103
Handheld Systems
Handheld Transmitter
ULXD2
Cartridge
see options below
Microphone Clip
95T9279
Zipper Bag
95B2313
AA Alkaline batteries (2)
80B8201
Battery Contact Cover
65A15947
Choice of one (1) of the following:
SM58
RPW112
SM86
RPW114
SM87A
RPW116
Beta 58A
RPW118
Beta 87A
RPW120
Beta 87C
RPW122
Choice of one (1) of the following:
Instrument cable
WA302
Instrument Clip-on microphone
Beta 98H/C
Lavalier microphone
MX150, MX153, WL183,
WL184, WL185
Headset microphone
WH30TQG
Antennas
Band
1/2-Wave Receiver
Antennas
1/4-Wave Transmitter
Antennas
G50
95AA9279
95G9043 (Yellow)
G51
95AA9279
95G9043 (Yellow)
G52
95AA9279
95G9043 (Yellow)
H51
95AL9279
95D9043 (Gray)
H52
95AL9279
95D9043 (Gray)
J50
95AK9279
95E9043 (Black)
K51
95AJ9279
95E9043 (Black)
L50
95AD9279
95E9043 (Black)
L51
95AD9279
95E9043 (Black)
P51
95AF9279
95F9043 (Blue)
R51
95M9279
95F9043 (Blue)
AB
95M9279
N/A
Q51
95M9279
N/A
X50
95V9279
95H9043 (Red)
Optional Accessories
Shure Rechargeable Battery
SB900
UHF Powered Directional Antenna
UA874WB
8-Bay Battery Charger
SBC800
Passive Directional Antenna
PA805SWB
Dual Docking Battery Charger
SBC200
Carrying Case
WA610
Coaxial Cable, BNC-BNC, RG58C/U
type, 50 Ohm, 2 ft length (0.6 m)
UA802
Y-Cable for Bodypack Transmitters
AXT652
UA806
Active Antenna Spitter
UA845SWB
Coaxial Cable, BNC-BNC, RG58C/U
type, 50 Ohm, 6 ft length (2 m)
Passive Antenna Splitter/Combiner Kit
UA221
UA825
UHF Line Amplifier
UA830WB
Coaxial Cable, BNC-BNC, RG8X/U
type, 50 Ohm, 25 ft length (7.5 m)
UHF Antenna Power Distribution
Amplifier (U.S.A.)
UA844SWB
Coaxial Cable, BNC-BNC, RG8X/U
type, 50 Ohm, 50 ft length (15 m)
UA850
UHF Antenna Power Distribution
Amplifier (Europe)
UA844SE
Coaxial Cable, BNC-BNC, RG213/U
Type, 50 Ohm, 100 ft length (30 m)
UA8100
Front Mount Antenna Kit (Includes 2
cables and 2 bulkhead
UA600
Remote Antenna Bracket with BNC
Bulkhead Adapter
UA505
28
Certifications
This Class B digital apparatus complies with Canadian ICES-003. Cet
appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
ULXD1, ULXD2, ULXD4D, ULXD4Q
This product meets the Essential Requirements of all relevant European
directives and is eligible for CE marking.
Meets requirements of the following standards: EN 300 422 Parts 1 and
2, EN 301 489 Parts 1 and 9.
ULXD1, ULXD2
Certified under FCC Part 74.
Certified by IC in Canada under RSS-123 and RSS-102.
IC: 616A-ULXD1 G50, 616A-ULXD1 H50, 616A-ULXD1 J50,
616A-ULXD1 L50; 616A-ULXD2 G50, 616A-ULXD2 H50, 616A-ULXD2
J50, 616A-ULXD2 L50.
FCC: DD4ULXD1G50, DD4ULXD1H50, DD4ULXD1J50, DD4ULXD1L50;
DD4ULXD2G50, DD4ULXD2H50, DD4ULXD2J50, DD4ULXD2L50.
ULXD4D, ULXD4Q
Approved under the Declaration of Conformity (DoC) provision of FCC
Part 15.
Certified in Canada by IC to RSS-123.
IC: 616A-ULXD4D G50, 616A-ULXD4D J50, 616A-ULXD4D L50;
616A-ULXD4Q G50, 616A-ULXD4Q J50, 616A-ULXD4Q L50.
Conforms to electrical safety requirements based on IEC 60065.
This device complies with Industry Canada licence-exempt RSS
standard(s). Operation of this device is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas
produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.
Note: EMC conformance testing is based on the use of supplied and
recommended cable types. The use of other cable types may degrade
EMC performance.
The CE Declaration of Conformity can be obtained from Shure
Incorporated or any of its European representatives. For contact
information please visit www.shure.com
The CE Declaration of Conformity can be obtained from: www.shure.com/
europe/compliance
LICENSING INFORMATION
Licensing: A ministerial license to operate this equipment may be required
in certain areas. Consult your national authority for possible requirements.
Changes or modifications not expressly approved by Shure Incorporated
could void your authority to operate the equipment. Licensing of Shure
wireless microphone equipment is the user’s responsibility, and licensability
depends on the user’s classification and application, and on the selected
frequency. Shure strongly urges the user to contact the appropriate
telecommunications authority concerning proper licensing, and before
choosing and ordering frequencies.
Information to the user
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING: Danger of explosion if battery incorrectly replaced.
Operate only with Shure compatible batteries.
Note: Use this receiver only with the included power supply or a Shureapproved equivalent.
WARNING
• Battery packs may explode or release toxic materials. Risk of fire or
burns. Do not open, crush, modify, disassemble, heat above 140°F
(60°C), or incinerate
• Follow instructions from manufacturer
• Never put batteries in mouth. If swallowed, contact your physician or local
poison control center
• Do not short circuit; may cause burns or catch fire
• Do not charge or use battery packs with other than specified Shure
products
• Dispose of battery packs properly. Check with local vendor for proper
disposal of used battery packs
• Batteries (battery pack or batteries installed) shall not be exposed to
excessive heat such as sunshine, fire or the like
Authorized European representative:
Shure Europe GmbH
Headquarters Europe, Middle East & Africa
Department: EMEA Approval
Jakob-Dieffenbacher-Str. 12
75031 Eppingen, Germany
Phone: 49-7262-92 49 0
Fax: 49-7262-92 49 11 4
Email: EMEAsupport@shure.de
29
FREQUENCIES FOR EUROPEAN COUNTRIES
ULXD-G51 470 - 534 MHz, max. 20 mW
Country Code
Code de Pays
Codice di paese
Código de país
Länder-Kürzel
A, B, BG, CH, CY, CZ, D, EST
F, GB, GR, H, I, IS, L, LT
NL, P, PL, S, SK, SLO
DK, FIN, M, N
Frequency Range
Gamme de frequences
Gamme di frequenza
Gama de frequencias
Frequenzbereich
470 - 534 MHz *
470 - 534 MHz *
470 - 534 MHz *
All other countries
HR, E, IRL, LV, RO, TR
ULXD-H51 534 - 598 MHz, max. 20 mW
Country Code
Code de Pays
Codice di paese
Código de país
Länder-Kürzel
A, B, BG, CH, CY, CZ, D, EST
F, GB, GR, H, I, IS, L, LT
NL, P, PL, S, SK, SLO
DK, FIN, M, N
Frequency Range
Gamme de frequences
Gamme di frequenza
Gama de frequencias
Frequenzbereich
534 - 598 MHz *
534 - 598 MHz *
534 - 598 MHz *
All other countries
HR, E, IRL, LV, RO, TR
ULXD-P51 710 - 782 MHz, max. 20 mW
Country Code
Code de Pays
Codice di paese
Código de país
Länder-Kürzel
A, B, BG, CH, CY, CZ, D, EST, F, GB,
GR, H, I, IS, L, LT, NL, P, PL, S, SK, SLO
RO
DK, E, FIN, HR, IRL, LV, M, N, TR
all other countries
Frequency Range
Gamme de frequences
Gamme di frequenza
Gama de frequencias
Frequenzbereich
710 - 782 MHz *
710 - 782 MHz *
“718-719; 726-727; 734-743;
750-751; 758-759 MHz*”
ULXD-R51 800 - 810 MHz, max. 20 mW
Country Code
Code de Pays
Codice di paese
Código de país
Länder-Kürzel
A, B, BG, CH, CY, CZ, D, DK, E, EST
F, FIN, GB, GR, H, HR, I, IRL, IS, L, LT
LV, M, N, NL, P, PL, S, SK, SLO, TR
All other countries
Frequency Range
Gamme de frequences
Gamme di frequenza
Gama de frequencias
Frequenzbereich
800 - 810 MHz*
ULXD-K51 606 - 670 MHz, max. 20 mW
Country Code
Code de Pays
Codice di paese
Código de país
Länder-Kürzel
A, B, BG, CH, CY, CZ, D, EST
F, GB, GR, H, I, IS, L, LT
NL, P, PL, S, SK, SLO
RO
Frequency Range
Gamme de frequences
Gamme di frequenza
Gama de frequencias
Frequenzbereich
606 - 670 MHz *
606 - 670 MHz *
606 - 670 MHz *
646-647;654-655;662-663 MHz*
All other countries
DK, E, FIN, HR, IRL, LV, M, N, TR
* IMPORTANT
NOTE: THIS EQUIPMENT MAY BE CAPABLE OF OPERATING ON SOME FREQUENCIES NOT AUTHORIZED IN YOUR REGION. PLEASE CONTACT YOUR
NATIONAL AUTHORITY TO OBTAIN INFORMATION ON AUTHORIZED FREQUENCIES AND RF POWER LEVELS FOR WIRELESS MICROPHONE PRODUCTS
IN YOUR REGION.
A ministerial license may be required to operate this equipment in certain areas. Consult your national authority for possible requirements.
* WICHTIG
HINWEIS: DIESES GERÄT KANN MÖGLICHERWEISE AUF EINIGEN FREQUENZEN ARBEITEN, DIE IN IHREM GEBIET NICHT ZUGELASSEN SIND. WENDEN
SIE SICH BITTE AN DIE ZUSTÄNDIGE BEHÖRDE, UM INFORMATIONEN ÜBER ZUGELASSENE FREQUENZEN UND ERLAUBTE SENDELEISTUNGEN FÜR
DRAHTLOSE MIKROFONPRODUKTE IN IHREM GEBIET ZU ERHALTEN.
Zulassung: In einigen Gebieten ist für den Betrieb dieses Geräts u.U. eine behördliche Zulassung erforderlich. Wenden Sie sich bitte an die zuständige Behörde, um
Informationen über etwaige Anforderungen zu erhalten.
*IMPORTANT
REMARQUE: IL EST POSSIBLE QUE CE MATÉRIEL SOIT CAPABLE DE FONCTIONNER SUR CERTAINES FRÉQUENCES NON AUTORISÉES LOCALEMENT.
SE METTRE EN RAPPORT AVEC LES AUTORITÉS COMPÉTENTES POUR OBTENIR LES INFORMATIONS SUR LES FRÉQUENCES ET NIVEAUX DE PUISSANCE HF AUTORISÉES POUR LES SYSTÈMES DE MICROPHONES SANS FIL LOCALEMENT.
Autorisation d’utilisation : Une licence officielle d’utilisation de ce matériel peut être requise dans certains pays. Consulter les autorités compétentes pour les
exigences possibles.
*IMPORTANTE
NOTA: QUESTO APPARECCHIO PUÒ ESSERE IN GRADO DI FUNZIONARE A FREQUENZE NON AUTORIZZATE NELLA REGIONE IN CUI SI TROVA
L’UTENTE. RIVOLGERSI ALLE AUTORITÀ COMPETENTI PER OTTENERE LE INFORMAZIONI RELATIVE ALLE FREQUENZE ED AI LIVELLI DI POTENZA RF
AUTORIZZATE NELLA PROPRIA REGIONE PER I PRODOTTI MICROFONICI SENZA FILI.
Concessione della licenza all’uso: per usare questo apparecchio, in certe aree può essere necessaria una licenza ministeriale. Per i possibili requisiti, rivolgersi alle
autorità competenti.
*IMPORTANTE
NOTA: ES POSIBLE QUE ESTE EQUIPO FUNCIONE EN ALGUNAS FRECUENCIAS NO AUTORIZADAS EN SU REGION. POR FAVOR CONTACTE A LA AUTORIDAD NACIONAL PARA OBTENER INFORMACION ACERCA DE LAS FRECUENCIAS AUTORIZADAS Y LOS NIVELES DE POTENCIA DE RADIOFRECUENCIA
PARA PRODUCTOS CON MICROFONOS INALAMBRICOS EN SU ZONA.
Licencia de uso: Se puede requerir una licencia ministerial para utilizar este equipo en algunas áreas. Consulte a la autoridad nacional sobre los posibles requisitos.
30
Europe, Middle East, Africa:
Shure Europe GmbH
Jakob-Dieffenbacher-Str. 12,
75031 Eppingen, Germany
Phone: 49-7262-92490
Fax: 49-7262-9249114
Email: info@shure.de
PT. GOSHEN SWARA INDONESIA
Kompleks Harco Mangga Dua Blok L No. 35 Jakarta Pusat
I.16.GSI31.00501.0211
31

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27
Create Date                     : 2013:08:06 16:21:37-05:00
Metadata Date                   : 2013:08:06 16:22:23-05:00
Modify Date                     : 2013:08:06 16:22:23-05:00
Creator Tool                    : Adobe InDesign CS6 (Windows)
Instance ID                     : uuid:e58767f2-804e-453b-8e47-601f861c198a
Original Document ID            : xmp.did:22B150A06976E011B21EBF115D01AC7E
Document ID                     : xmp.id:DB19522DDEFEE211B0029FA6A4869D65
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:F5F7F5AFDDFEE211B0029FA6A4869D65
Derived From Document ID        : xmp.did:E746A81EC2E0E111AC189B95E12FD93D
Derived From Original Document ID: xmp.did:22B150A06976E011B21EBF115D01AC7E
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CS6 (Windows)
History Changed                 : /
History When                    : 2013:08:06 16:21:37-05:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 10.0.1
Trapped                         : False
Page Count                      : 31
Creator                         : Adobe InDesign CS6 (Windows)

EXIF Metadata provided by EXIF.tools