Snapper EZF2100DKU User Manual ZERO TURN RIDER Manuals And Guides L0808251

SNAPPER Lawn, Riding Mower Rear Engine Manual L0808251 SNAPPER Lawn, Riding Mower Rear Engine Owner's Manual, SNAPPER Lawn, Riding Mower Rear Engine installation guides

EZF2100DKU, EZF2300GKU, EZF5200M, EZF6100M L0808251

User Manual: Snapper EZF2100DKU EZF2100DKU SNAPPER ZERO TURN RIDER - Manuals and Guides View the owners manual for your SNAPPER ZERO TURN RIDER #EZF2100DKU. Home:Lawn & Garden Parts:Snapper Parts:Snapper ZERO TURN RIDER Manual

Open the PDF directly: View PDF PDF.
Page Count: 32

Safety Instructions & Operator's Manual for
OUT FRONT Z-RIDER
HYDRO DRIVE
SERIES 0
POWER UNIT MODELS
EZF2100DKU
EZF2300GKU
IMOWER UNIT MODELS
EZF5200M IEZF6100M
MODEL NUMBER EXPLANATION
EXPORT MODEL
DRIVE SYSTEM TYPE
MOWER ORIENTATION
ENGINE HP
E - Export Model
Z - Zero Turning - Hydro Drive
F - Out Front Mower
Z - Zero Turning - Hydro Drive
F - Out Front Mower
EIz
I
21 - Engine Horse Power
23 - Engine Horse Power
F121 001 O IKU
POWER UNIT
O0- Series Designation
ENGINE MODEL
ENGINE TYPE
SERIES DESIGNATION
D - Diesel Fuel Engine KU - Kubota Engine
G - Gasoline Fuel Engine
MOWER UNIT
62 - Mower Cutting Width 00 - Series Designation
61 - Mower Cutting Width
M - Mower Deck
Thank you for buying a SNAPPER Productf Before operating your machine, read this manual carefully and pay particular
attention to the "IMPORTANT SAFETY INSTRUCTIONS" on Pages 2 & 3. Remember that all power equipment can be
dangerous if used improperly. Also keep in mind that SAFETY requires careful use in accordance with the operating
instructions and common sense!
SNAPPER, McDonough,GA., 30253 U.S.A.
COPYRIGHT © 2001
SNAPPER INC.
ALL RIGHTS RESERVED
INSTRUCTION No. 7-4370 (I.R. 4/6/01)
AIMPORTANT SAFETY INSTRUCTIONS
WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects that
can cause injury and damage! Failure to comply with the following SAFETY instructions could result in serious
injury or death to the operator or other persons. The owner of the machine must understand these instructions
and must allow only persons who understand these instructions to operate machine. Each person operating the
machine must be of sound mind and body and must not be under the influence of any substance, which might
impair vision, dexterity or judgment. If you have any questions pertaining to your machine which your dealer
cannot answer to your satisfaction, call or write the Customer Service Department at SNAPPER, McDonough,
Georgia 30253. Phone: (1-800-935-2967).
PROTECTION FOR CHILDREN
Tragic accidents can occur if the operator is not alert
to the presence of children. Children are often
attracted to the machine and the mowing activity.
Never assume that children will remain where you last
saw them.
1. KEEP children out of the mowing area and under
the watchful care of a responsible adult.
2. DO NOT allow children in yard when machine is
operated (even with the blades OFF).
3. DO NOT allow children or others to ride on
machine or on attachments (even with the blade
OFF). They may fall and be seriously injured.
4. DO NOT allow pre-teenage children to operate
machine.
5. ALLOW only adults or responsible teenagers with
mature judgment under close adult supervision to
operate machine.
6. DO NOT operate blades in reverse. STOP BLADES.
LOOK and SEE behind and down for children, pets
and hazards before and while backing.
7. USE EXTRA CARE when approaching blind
corners, shrubs, trees, or other objects that may
obscure vision.
PROTECTION AGAINST TIPOVERS
Slopes are a major factor related to loss-of-control
and tip-over accidents, which can result in severe
injury or death. All slopes require extra CAUTION. If
you cannot back up the slope or if you feel uneasy on
the slope, DO NOT mow it. Use extra care with grass
catchers or other attachments; these affect the
handling and the stability of the machine.
1. DO NOT operate machine on slopes exceeding 15
degrees (27% grade).
2. Exercise EXTREME CAUTION on slopes above 10
degrees (18% grade). Turn blades OFF when
traveling uphill. Use a slow speed and avoid
sudden or sharp turns.
3. DO NOT operate machine back and forth across
face of slopes. Operate up and down. Practice on
slopes with blades off.
PROTECTION AGAINST TIPOVERS
(Continued From Previous Column)
4. AVOID uphill starts. If machine stops going uphill
or tires lose traction, turn blades OFF and back
slowly down the slope.
5. STAY ALERT for holes and other hidden hazards.
Tall grass can hide obstacles. Keep away from
ditches, washouts, culverts, fences and
protruding objects.
6. KEEP A SAFE DISTANCE (at least 3 feet) away
from edge of ditches and other drop offs. The
machine could turn over if an edge caves in.
7. Always begin forward motion slowly and with
caution.
8. Use weights or aweighted load carrier in
accordance with instructions supplied with a
grass catcher. DO NOT operate machine on slopes
exceeding 10 degrees (18% grade)when equipped
with grass catcher.
9. DO NOT put your foot on the ground to try to
stabilize the machine.
10. DO NOT operate machine on wet grass. Reduced
traction could cause sliding.
11. DO NOT operate machine under any condition
where traction, steering or stability is doubtful.
12. Operator Protective Structures are available for
this machine through your local Snapper dealer.
PREPARATION
1. Read, understand and follow
.
3.
.
instructions and
warnings in this manual and on the machine,
engine and attachments. Know the controls and
the proper use of the machine before starting.
Only mature, responsible persons shall operate
the machine and only after proper instruction.
Data indicates that operators age 60 and above,
are involved in alarge percentage of mower-
related injuries. These operators should evaluate
their ability to operate the mower safely enough to
protect themselves and others from serious injury.
Handle fuel with extra care. Fuels are flammable and
vapors are explosive. Use only an approved fuel
container. DO NOT remove fuel cap or add fuel with
engine running. Add fuel outdoors only with engine
stopped and cool. Clean spilled fuel from machine.
DO NOT smoke.
AIMPORTANT SAFETY INSTRUCTIONS
PREPARATION
(Continued From Previous Page)
5. Practice operation of machine with BLADES OFF
to learn controls and develop skills.
6. Check the area to be mowed and remove all
objects such as toys, wire, rocks, limbs and other
objects that could cause injury if thrown by blades
or interfere with mowing.
7. Keep people and pets out of mowing area.
Immediately, STOP blades, STOP engine, and
STOP machine if anyone enters the area.
8. Check shields, deflectors, switches, blade controls
and other safety devices frequently for proper
operation and location.
9. Make sure all safety decals are clearly legible.
Replace if damaged.
10. Protect yourself when mowing and wear safety
glasses, long pants and substantial footwear.
11. Know how to STOP blades and engine quickly in
preparation for emergencies.
12. Use extra care when loading or unloading the
machine into atrailer or truck.
13. Check grass catcher components frequently for
signs of wear or deterioration and replace as
needed to prevent injury from thrown objects
going through weak or worn spots.
OPERATION
1. Mount and dismount machine from left side.
2. Start engine from operator's seat, if possible. Make
sure blades are OFF and parking brake is set.
3. DO NOT leave machine with engine running. Stop
engine. Stop blades. Set brake. Remove key.
4. DO NOT operate machine unless properly seated
with feet on feet rests or pedal(s).
5. STOP BLADES and ENGINE and make sure blades
have stopped before removing grass catcher or
unclogging mower to prevent loss of fingers or
hand.
6. Blades must be OFF except when cutting grass.
Set blades in highest position when mowing over
rough ground.
7. Keep hands and feet away from rotating blades
underneath deck. DO NOT place foot on ground
while BLADES are ON or machine is in motion.
8. DO NOT operate machine without entire grass
catcher or guards in place. DO NOT point
discharge at people, passing cars, windows or
doors.
9. Slow down before turning.
10. Watch out for traffic when near or crossing
roadways.
11. STOP engine immediately after striking an
obstruction. Inspect machine and repair damage
before resuming operation.
OPERATION
(Continued From Previous Column)
12. Mow only in daylight or with good artificial light.
13. Move motion control levers SLOWLY to maintain
control during speed and directional changes.
14. Exercise CAUTION when pulling loads. DO NOT
pull loads greater than 300 pounds. Avoid jack
knifing. DO NOT turn sharply.
15. DO NOT operate engine in enclosed areas. Engine
exhaust gases contain carbon monoxide, a deadly
poison.
MAINTENANCE
1. DO NOT store machine or fuel container inside
where fumes may reach an open flame, spark or
pilot light such as in a water heater, furnace,
clothes dryer or other gas appliance. Allow
engine to cool before storing machine in an
enclosure. Store fuel container out of the reach
of children in awell ventilated, unoccupied
building.
2. Keep engine free of grass, leaves or excess
grease to reduce fire hazard and engine
overheating.
3. When draining fuel tank, drain fuel into an
approved container outdoors and away from
open flame.
4. Check brakes frequently; adjust, repair or
replace as needed.
5. Keep all bolts, nuts and screws properly tight.
Check that all cotter pins are in proper position.
6. Always provide adequate ventilation when
running engine. Engine exhaust gases contain
carbon monoxide, an odorless and deadly
poison.
7. Disconnect negative (black) cable from battery
before performing maintenance or service.
Cranking engine could cause injury.
8. DO NOT work under machine without safety
blocks.
9. Service engine and make adjustments only
when engine is stopped. Remove spark plug
wire(s) from spark plug(s) and secure wire(s)
away from spark plug(s).
10. DO NOT change engine governor speed
settings or overspeed engine.
11. Lubricate machine at intervals specified in
manual to prevent controls from binding.
12. Mower blades are sharp and can cut. Wrap the
blades or wear heavy leather gloves and use
CAUTION when handling them.
13. DO NOT test for spark by grounding spark plug
next to spark plug hole; spark plug could ignite
gas exiting engine.
14. Have machine serviced by an authorized
SNAPPER dealer at least once a year and have
the dealer install any new safety devices.
15. Use only genuine SNAPPER replacement parts
to assure that original standards are
maintained.
TABLE OF CONTENTS
IMPORTANT SAFETY INSTRUCTIONS ................................................ 2-3
TABLE OF CONTENTS ............................................................................. 4
SECTION 1 - FAMILIARIZATION .............................................................. 5
SYMBOLS ........................................................................................................... 6-8
SECTION 2 - OPERATING INSTRUCTIONS ....................................... 9-13
Pre-start Checklist ................................................................................................. 9
Starting & Stopping Engine, Blades & Parking Brake ..................................... 10-12
Starting & Stopping Mower Blades ....................................................................... 11
Parking Brake ....................................................................................................... 12
Cutting Height Adjusting ....................................................................................... 12
Driving & Stopping Machine ................................................................................. 13
SECTION 3 - MAINTENANCE INSTRUCTIONS ............................... 14-18
Change Engine Oil ................................................................................................ 14
Check Mower Blade ............................................................................................. 14
Check Mower Drive Belt ..................................................................................... 15
Check Belt Tension ............................................................................................ 15
Service- After every 25 Hours (Engine) ............................................................ 15
Service - After every 25 Hours (Mower Components) ....................................... 15
Mower Blade Spindle Lubrication .................................................................... 15
Mower Deck Linkage Lubrication .................................................................... 15
Front Wheel Bearings Lubrication ................................................................... 16
Transaxle Lubrication ...................................................................................... 16
Power Transfer Shaft Lubrication .................................................................... 16
Other Lubrication ............................................................................................... 16
Before Operating Mower ...................................................................................... 16
Annually - End of Season Service ................................................................... 16-17
Fuel Filter Replacement ....................................................................................... 17
Deck Removal ................................................................................................. 17-18
Power Transfer Shaft Removal ............................................................................ 18
SECTION 4 - ADJUSTMENTS AND REPAIR .................................... 19-25
Neutral Position Adjustments ............................................................................... 19
Mower Deck Adjustment (Levelness) .............................................................. 19-20
Parking Brake Adjustment .................................................................................... 20
Engine Adjustments & Repair ............................................................................... 20
Mower Blade Replacement ............................................................................. 20-21
Blade Sharpening ................................................................................................. 21
Mower Drive Belt, Engine Belt & Hydro Pump Belt Removal & Replacement ..... 22
Battery Removal ................................................................................................... 23
Battery Installation ................................................................................................ 23
Battery Service & Charging ............................................................................. 23-24
Battery Testing ...................................................................................................... 24
New Battery Preparation ....................................................................................... 24
Mower Spindles (Field Serviceable Spindles) Bearing Replacement ................... 25
TROUBLESHOOTING ........................................................................ 26-27
SERVICE SCHEDULE ............................................................................. 28
Maintenance/Replacement Parts ......................................................................... 28
WARRANTY ............................................................................................ 29
IMPORTANT
NOTICE: Operator Protective Structures are available as optional kits for the Mid-Mount and Out-Front Z-Rider machines. These
structures, when installed and used properly can offer additional security to the operator against serious injury in the event of a tip over
accident. Operator Protective Structures may be required by local ordinances. Discuss your mowing application and ordinances with
your local Snapper Dealer.
I IMPORTANT: DIESEL AND GAS UNITS LOOK VERY SIMILIAR. DO NOT PUT GAS IN DIESEL MACHINE OR DIESEL IN GAS I
I
MACHINE. ENGINE DAMAGE MAY RESULT.
Section 1 - FAMILIARIZATION
MOTION
CONTROL
(JOYSTICK)
OPERATOR'S SEAT
CONTROL PANEL
IGNITION AMP BLADE SWITCH
SWITCH METER ,/
DECK
LIGHT LIFT
HOUR SWITCH SWITCH
METER
FUEL TANK
PARKING BRAKE
ENGINESPEED
CONTROL
CONTROL PANEL
(SEEINSET)
DECK HEIGHT OF
CUTDECAL
DECK COVER
CASTER
WHEEL
BRACKET
DISCHARGE
DEFLECTOR
FIGURE 1.1
1.1 INTRODUCTION
This manual has been prepared for the operator's of the
SNAPPER OUT FRONT Z-RIDER. Its purpose, aside
from recommending standard operating procedures and
routine service requirements, is to promote SAFETY
through the use of accepted operating practices. Read,
Understand and Follow the IMPORTANT SAFETY
INSTRUCTIONS on Page 2 and 3 of this manual and All
SAFETY messages on the OUT FRONT Z-RIDER and its
attachments before operating. SNAPPER recommends
returning the OUT FRONT Z-RIDER to an authorized
SNAPPER dealer annually for inspection and addition of
any new devices which might upgrade the safety of the
mower.
1.2 NOMENCLATURE
The nomenclature information above, Figure 1.1,
shows the essential parts of the SNAPPER OUT
FRONT Z-RIDER. It is recommended that all operator's
of this equipment become thoroughly familiar with the
controls, components, and operation of this machine
before operating. Specific details involving the engine
are found in the separate engine owner's manual.
Study these manuals before operating and keep both
handy for future reference. For the nearest SNAPPER
dealer in your area, check the yellow pages under the
heading LAWN MOWERS. For engine parts and
service, look for the engine manufacturer's dealers
under the heading, ENGINES - gasoline.
SYMBOLS
Hearing protection
required during
machine operation.
Sound Power Level
e------- produced by machine and
cutter deck - Lwa 105.
e--PARKING BRAKE CONTROL
LEVER- Push control
forward to disengage (un-
lock/off).
Pull control rearward to
engage (lock/on).
IMPORTANT: Parking Brake
must be engaged (locked) to
start engine.
ENGINE STOP (OFF)
ENGINE
RUN (ON) MACHINE MOTION CONTROL - Single lever, multi-
directional & continuously variable, controls
direction of motion & speed of motion. Forward
displacement of control produces forward motion.
Rearward displacement of control produces
rearward motion. Increased control displacement
produces increased speed of motion.
ENGINE
GLOW PLUG
PRE-HEAT
ENGINE
START
BLADE CONTROL
SWITCH - Pull switch up
(ON) to engage blade.
Push switch down (OFF) to
disengage blade.
IMPORTANT: Mower Blade
Control Switch must be in
(OFF) disengaged position
to start engine.
SYMBOLS
e----ENGINE SPEED
CONTROL
RABBIT-FAST
TURTLE-SLOW
T
DIESEL FUEL ONLY
T
CUTTING HEIGHT CONTROL
SWITCH -
Move switch in direction of plus
symbol to increase cutting height/
Move switch in direction of minus
symbol to decrease cutting height.
Read and
understand all
manuals and
instructions
furnished with
the machine.
Keep asafe
distance from the
machine. Always
clear the mowing
area of all objects
that could cause
injury if thrown
by blades.
DO NOT operate machine on
slopes greater than 10 degrees
(17%). DO NOT mow across face
of slope.
TTKeep children and others out of
mowing area and under the watchful
care of a responsible adult. Never
assume children will stay where you
last saw them. Look down and behind
machine before and while backing.
DO NOT operate blades in reverse.
SYMBOLS
DO NOT perform any service, maintenance,
adjustments or repairs with the engine
running. STOP engine. STOP blades. Engage
Parking Brake. REMOVE key. Read Manual.
DO NOT touch or approach
machine components until all
motion has completely stopped.
A
w
HOT SURFACE! Stay clear. T
DO NOT open or remove guards or shields
while engine is running. STOP engine. Allow
all motion to completely stop before
approaching.
T___DO NOT open or remove safety shields while
engine is running. DO NOT operate machine
unless all guards and shields are in place and
securely fastened.
A
v
DO NOT approach
mower while engine is
running. STOP engine.
Allow all motion to
completely stop before
approaching.
DO NOT open or remove guards or shields
while engine is running. STOP engine.
Allow all motion to completely stop before
approaching.
Section 2 - OPERATING INSTRUCTIONS
2.1
2.1.1.
PRE-START CHECK LIST 2.1.5.
Make the following checks and perform the
service required before each start-up.
Check tires and add or release air as needed to
bring pressure in drive tires to: 12 psi (Turf Type
Tires), 5 psi (All Terrain Type Tires) and 25 psi in 2.1.6.
rear caster tires. Pressure in front deck caster
wheels should be 25 psi.
Check guards, deflectors and covers to make
sure all are in place and securely tightened. 2.1.7.
Check engine oil and add oil as needed to bring
level up to the FULL mark. Refer to engine owner's
manual for oil specifications. See Figure 2.1.
FULL
MARK
AIR FILTER ASSEMBLY IS
SHOWN REMOVED
Clean exterior surfaces of cutting deck and
engine of any accumulation of dirt, grass, oil, etc.
Keep engine radiator air intake screen and
cooling fins clear at all times. Check often in dry
operating conditions.
Add fresh fuel to tank of the Out Front Z-Rider
outside where fumes can safely dissipate. Make
sure fuel filler cap is tight. Refer to engine
owner's manual for fuel specifications.
COLD ENGINE ONLY - Check engine coolant
(antifreeze/water) and add coolant in the reserve
tank as needed to bring level up to the FULL
mark. Refer to engine owner's manual for
coolant ratio specifications. See Figure 2.3.
WARNING IIL I
DO NOT remove cap from radiator when engine and I
coolant are hot. Coolant is pressurized, severeI
burns could result. I
OIL DIP
STICK
2.1.4.
FIGURE 2.1
Check Blade switch to insure it works freely. Switch
is pulled "OUT" for blade engagement or pushed
back "IN" for blade disengagement. See Figure 2.2.
IMPORTANT: Disengagement stops blades.
BLADE
SWITCH
AMP _
IGNITION METER
SWITCH
FULL COOLANT
MARK
LOW COOLANT MARK
(COOLANT SHOULD BE
ADDED)
COOLANT RESERVE
TANK
FIGURE 2.3
2.1.8. (Diesel Engine Models Only) Move fuel cock to
the "ON" position. See Figure 3.8.
LIGHT
HOUR SWITCH
METER
............................................................ q
BLADE SWITCH:
PULL"OUT'TO ENGAGE BLADE.
PUSH"IN'TO DISENGAGE BLADE.
• ............................................................ i
FIGURE 2.2
DECK
LIFT
SWITCH
IMPORTANT: This machine is equipped with a
WARNING beeper. The beeper will sound when engine
oil pressure is low or engine temperature is high. If this
beeper sounds, stop operation immediately. Do not
resume operation until the cause has been determined
and proper action taken. Beeper function can be verified
(with engine stopped) by turning key to "RUN" position.
Section 2 - OPERATING INSTRUCTIONS
IMPORTANT: This Out Front Z-Rider is equipped with
hydrostatic drive. The forward and rearward movement
of the machine is controlled by ajoystick lever,
Joystick operations should be performed only from the
operator's position in the seat. Asmall movement of
the joystick can cause the machine to move instantly.
Move joystick very carefully and slowly,
ROLL RELEASE: To roll the machine without the
engine running, pressure within the hydraulic pumps
must be released. There is one lever on the upper
right side of each pump that is used to release the
pressure. Rotate lever counter clockwise and secure
in that position. See Figure 2.4.
PRESSURE
RELEASE LEVER LEVER 18 IN POSITION FOR
PROPELLING RIDER UNDER
IT'S OWN POWER (RIDER
WILL NOT ROLL WITH LEVER
IN THIS POSITION)
2.2.1.
Moving the joystick farther from the neutral
position will cause the speed of motion to
increase. To turn, move the joystick towards
the side you want to turn to.
DO NOT make sudden changes in speed or
direction. Always slow machine motion before
turning. To stop the motion of the machine
bring the joystick back to the neutral position.
Engage parking brake.
STARTING ENGINE
When the ignition key is turned to "START", the
engine will not turn over unless the parking
brake is engaged and the blade switch is in the
"OFF" position!
Be seated on the Out Front Z-Rider before
attempting to start the engine with the key
switch.
1. Complete pre-start checklist.
2. Sit in operator's seat.
3. Push blade switch in to "OFF", blades
disengaged position and engage parking brake.
See Figure 2.2.
PRESSURE LEVER 18 ROTATED COUNTER
RELEASE LEVE.R_ _CLOCKWISE AND LATCHED IN A
.o..o...°
RIDER (RIDER WILL NOT PROPEL
ITSELF WITH LEVER IN THIS
FIGURE 2.4
2.2 STARTING & STOPPING -ENGINE, BLADES &
PARKING BRAKE
This machine is equipped with dual
hydrostatic wheel drive transmissions. Each
transmission is controlled by asingle motion
control lever or joystick. This single control
lever (joystick) controls the direction of
motion, Forward and Reverse, and the speed
of motion. Move the joystick forward to propel
the machine forward. Move the control
rearward to propel the machine in reverse.
The speed of motion is continuously variable
from neutral (zero) to maximum.
\
FIGURE 2.5
4. Move engine speed control to a medium
speed position. See Figure 2.6.
5. IMPORTANT: (Gasoline Engine Only).
Move engine choke control to the choke position
to start a cold engine. After starting choke
control must be moved to "OFF" no choke
position.
10
Section 2 - OPERATING INSTRUCTIONS
2.2.1. STARTING ENGINE (Continued from previous page)
FAST ENGINE
SPEED POSITION
SLOW ENGINE
SPEED POSITION
ENGINE SPEED CONTROL
SHOWN IN "FAST" POSITION
FIGURE 2.6
6. IMPORTANT: (Diesel Engine Only) Use the
Glow Plug only if engine is cold or outside
temperature is cold. Rotate key counter
clockwise to the preheat position (GL letter
designation on switch) to allow the glow lamp to
heat up. Hold key in the Glow Plug position for a
maximum of 5 seconds See Figure 2.7.
7. Rotate key clockwise to the start position until
engine starts. See Figure 2.7.
NOTE: If after 5 seconds of cranking the engine does
not start, release the key and attempt starting again after
waiting for approximately 20 seconds.
DIESEL ENGINE SWITCH POSITION
STOP
POSITION RUN
GLOW PLUG OFF POSITION
PRE-HEAT GL_//_
ST START
POSITION
GAS ENGINE SWITCH POSITION
STOP
POSITION
OFF
ON_ ST
RUN
POSITION
START
POSITION
FIGURE 2.7
8. After engine starts, allow a brief warm-up until
engine runs smooth.
STOPPING -ENGINE
ENGINE
1. Stop engine by turning key to the "OFF"
position. Move engine speed control to turtle
"SLOW" position and key to "STOP" position.
See Figure 2.7.
DO NOT leave machine with engine running.
blades. STOP engine. Set brake. Remove key.
2.2.2. STARTING MOWER BLADES
1. With engine running, move engine speed
control to the Rabbit or "fast" position.
2. Pull the blade switch out into the "ON"
position to engage the mower blades.
3. Release the parking brake.
4. Move joystick carefully in the desired direction to
propel the machine. A small movement of the
joystick can cause the machine to move instantly.
Move joystick carefully and slowly.
i, WARNING
DO NOT operate blades in reverse. STOP BLADES.I
LOOK and SEE behind and down for children, pets I
and hazards before and while backing.
2.2.3. STOPPING MOWER BLADES
1. Push the blade switch in to "OFF" position to
disengage or stop the mower blades. See Figure
2.2.
WARNING
Once blades are disengaged, they should come to a
complete stop in 7 seconds. If the blades continue to
rotate after 7 seconds, the electric clutch should be
checked. Replacement of electric clutch may be
necessary. Return the machine to an authorized
Snapper dealer for replacement. DO NOT CONTINUE
to operate mower if blades fail to stop in 7 seconds.
11
Section 2 - OPERATING INSTRUCTIONS
2.2.4. PARKING BRAKE 2.2.5.
1. Engage parking brake by pulling the parking
brake lever back to the "ON" position. See
Figure 2.8.
2. Release parking brake by moving brake lever
down to the "OFF" position. See Figure. 2.9.
JOYSTICK IN
NEUTRAL
POSITION
CUTTING HEIGHT ADJUSTMENT
1. Adjust cutting height as desired to any
position, using deck lift switch. When in desired
height of cut, release switch. See Figure 2.10.
Observe the height of cut decal located on the
upper right top side of the deck to place deck at
the correct height of cut. See Figure 2.10.
NOTE: The engine does not have to be running
to adjust cutting height, but key switch must be
in the "ON" position.
DECK HEIGHT OF
CUT DECAL
PARKING
BRAKE
LEVER IN
ENGAGED ;
"ON"
POSITION /
FIGURE 2.8
_" PARKING BRAKE DISENGAGED
"OFF" POSITION
t/
DECK LIFT
SWITCH
FIGURE 2.10
I,_)i, WARNING I
DO NOT park the machine on slopes. DO NOT leave
machine with engine running. Stop engine. StoP l
blades. Set brake. Remove key. I
FIGURE 2.9
12
Section 2 - OPERATING INSTRUCTIONS
2.3. OPERATION - MOTION CONTROL
2.3.1. DRIVING MACHINE
IMPORTANT: The joystick lever has to be manually
moved to propel machine. Always return the joystick
with hand assistance to the neutral position to stop
machine. Release the joystick and it will gradually
return toward the neutral position. When the parking
brake is engaged, it will lock joystick lever in the
neutral position. The engine will only crank or start if
parking brake lever is engaged and the blade switch
is in the "OFF" position.
1. With engine running, adjust engine speed control
to Rabbit or "Fast" position.
2. Release parking brake.
3. Move joystick lever carefully and slowly into
desired speed position. A small movement of the
joystick can cause the power unit to move instantly.
Move joystick carefully and slowly.
FORWARD - Move control forward.
REVERSE - Move control to the rear.
LEFT TURN - Move control towards left.
RIGHT TURN - Move control towards right.
ZERO RADIUS TURN - Move control diagonally
from neutral in desired direction. See Figure 2.11.
WARNING
DO NOT make turns at high speed. Slow machine
motion. Move motion control lever gently and with
caution. DO NOT make sudden changes in speed or
direction.
NEUTRAL POSITION
REARWARD
MOVEMENT LEFT
TURN
,_ RIGHT FORWARD
TURN MOVEMENT
\
FIGURE 2.11
13
Section 3 - MAINTENANCE
3.1 INTRODUCTION
To retain the quality of the SNAPPER Out Front Z-Rider,
use genuine SNAPPER replacement parts only. Contact a
local SNAPPER dealer for parts and service assistance.
For the correct part or information for a particular SNAPPER
Out Front Z-Rider, always mention the model and serial
number. SNAPPER recommends returning the Out Front
Z-Rider to an authorized SNAPPER dealer annually for
inspection and addition of any new devices which might
upgrade the safety of the Out Front Z-Rider. For the nearest
SNAPPER dealer in your area, check the yellow pages
under the heading LAWN MOWERS. For engine parts and
service, look for the engine manufacturer's dealers under
the heading, ENGINES - gasoline.
3.2 SERVICE - AFTER FIRST 5 HOURS
WARNING
DO NOT attempt any adjustments, maintenance or
service with the engine or blades running. Stop
blades. Stop engine. Set brake. Remove key.
Remove spark plug wires from spark plugs and (gas
only) secure wires away from spark plugs. Engine
and components are HOT. Avoid serious burns by
allowing all parts sufficient time to cool.
3.2.1. CHANGE ENGINE OIL
1. Place a 4 quart minimum capacity container
under the bottom of engine.
2. Remove the oil drain plug. See Figure 3.1.
ENGINE IS VIEWED FROM THE REAR
REMOVE OIL
FILTER
REMOVE OIL DRAIN
FIGURE 3.1
3. After all the oil has drained, reinstall oil drain
plug and tighten securely. See Figure 3.1. Wipe
up any oil that may have spilled. Dispose of
drained oil properly.
4. Fill engine crankcase with new oil. Refer to your
engine owner's manual for oil specifications.
5. Change oil filter at every oil change. Refer to
your engine owner's manual for service
instructions.
3.2.2. CHECK MOWER BLADE
1. Stop Engine.
2. Engage parking brake.
3. Turn key to "ON" position but DO NOT start
engine. Raise mower deck off the ground using
deck lift switch located to the right of operator as
viewed from the operator's position. Turn key to
"OFF" position. Remove key.
4. Use a hydraulic floor jack or hoist to raise deck
high enough to gain access to the underside of
deck. Secure deck with safety blocks.
WARNING
Wear heavy leather gloves when handling or working
around cutting blades. Blades are extremely sharp
and can cause severe injury. DO NOT use a cutting
blade that shows signs of excessive wear or
damage. Refer to Section "MOWER BLADE
REPLACEMENT" for proper blade inspection and
service procedures.
5. Check torque of blade mounting bolts. Torque
to 70 to 80 ft. Ibs. See Figure 3.2.
6. Check blade for sharpness, wear,
straightness and damage. Refer to Section
"BLADE WEAR LIMITS".
AIR
MOUNTING
BOLT
WASHER
TIGHTEN TO 70-80
FOOT POUNDS
FIGURE 3.2
14
Section 3 - MAINTENANCE
3.2.3.
3.3.2.
CHECK MOWER DRIVE BELT
1. Drive Belt Cover Removal
a. Lower deck to lowest setting.
b. Remove knobs that secure the deck
cover. See Figure 3.3.
c. Remove cover to gain access to deck belt.
REMOVE
FOUR
KNOBS
REMOVE
DECK COVER
FIGURE 3.3
2. Checking Belt Tension
The idler and spring provide proper belt tension
and require no adjustment. If belt is frayed, slit,
severed or belt strands exposed, replace belt
before operating mower.
AFTER EVERY 25 OPERATING HOURS
ENGINE
1. Engine Oil
Change engine oil. Refer to Section "CHANGE
ENGINE OIL". Refer to engine owner's manual
for oil specifications.
2. Air Filter
Refer to engine owner's manual for service
instructions.
3. Radiator - SEE WARNING
a. Clean radiator debris screen and cooling
fins thoroughly. Refer to engine owner's
manual for service instructions.
b. Check coolant level in reserve tank.
MOWER COMPONENTS
1. Mower Drive Belt
No adjustment required. Replace belt as
needed.
2. Mower Blade
Check blade for sharpness, wear, damage, and
torque. Refer to Section "MOWER BLADE
REPLACEMENT".
3. Mower Deck Levelness
Check mower deck for proper levelness. Adjust
as required. Refer to Section "MOWER DECK
ADJUSTMENT - LEVELNESS".
.Cleaning Mower Deck
a. Remove key from ignition switch.
b. Remove spark plug wire(s) and secure
away from spark plug(s). GAS ENGINE
ONLY.
c. Raise mower deck to its highest setting. It
may be necessary to raise mower deck
higher using a hydraulic floor jack. Secure
deck with safety blocks.
d. Clean underside of mower deck, removing
all accumulation of grass clippings and
debris.
e. Clean top of deck, removing all grass
clippings and debris.
.Mower Blade Spindle -Lubrication
a. Remove four knobs that secure the deck
cover.
b. Remove cover to gain access to
lubrication fitting located on the top of deck
below deck pulleys. Lubricate with Kendall
NLGI No. 2 lithium grease or equivalent, from
a grease gun until grease purges from vent
located on spindle housing underneath deck.
See Figure 3.4.
DECK PULLEYS
FIGURE 3.4
6. Mower Deck Linkage -Lubrication
Lubricate all mower deck linkage pivot points
with a light coat of motor oil.
l k, WARNING a,l
DO NOT remove cap from radiator when engine and I
coolant are hot. Coolant is pressurized, severeI
burns could result. I
15
Section 3 - MAINTENANCE
3.3.3. RIDING MOWER -LUBRICATION
1. Front & Rear Wheel Bearings
Lubricate with Kendall NLGI No. 2 lithium grease or
equivalent, from a grease gun. See Figure 3.5.
//
LUBRICATE
BEARINGS , // / i/,_ /
FRONT
WHEEL
3. Power Transfer Shaft
Lubricate power transfer shaft with Kendall NLGI
No. 2 lithium grease or equivalent, from a grease
gun. See Figure 3.7.
LUBRICATE POWER_
TRANSFER SHAFT
FIGURE 3.5
2. Transaxle
Check the level of fluid in both of the fluid reservoirs.
Wipe away all dirt and debris from around reservoir
cap before removing. Oil must remain absolutely
clean! Check with mower on a level surface with
engine "OFF". Fill reservoir as needed to bring level
up to 1-1/2 inches below the top of the filler neck.
Use dean, fresh premium hydraulic oil having a
viscosity equivalent to SAE 20W-20, SAE 30 or SAE
40. The fluid should be chemically stable,
incorporating rust and oxidation inhibitors. Make sure
funnels, pouring spouts and oil can are completely
clean. Reinstall reservoir cap. See Figure 3.6.
IMPORTANT: DO NOT remove or service the
transaxle fluid filters. This service should be made
periodically by an authorized SNAPPER dealer. See
the service schedule to determine the recommended
change interval.
OIL FILL 1-1/2
LINE
3.4
3.5
3.5.1.
FIGURE 3.7
4. OTHER LUBRICATION POINTS
Lubricate traction drive idlers, P.T.O. idlers,deck
caster wheel shafts, rear caster wheel shaft,
traction drive shaft bearings and mower deck
idler arm with Kendall NLGI No. 2 lithium grease
or equivalent, from a grease gun.
BEFORE OPERATING MOWER
1. Clean all dirt and debris from around the two
hydraulic fluid reservoirs. Especially around the
top and cap area.
2. Clean all dirt and debris from the radiator
debris screen and cooling fins.
3. Clean all dirt and debris from the cooling fins
on the engine and from both hydraulic pumps.
ANNUALLY (END OF EACH SEASON)
Perform all maintenance as required in
SERVICE SCHEDULE section of this manual.
ENGINE
Service engine according to engine owner's
manual.
(Continued on next Page)
HYDRAULIC OIL
RESERVOIR
IMPORTANT: FLUID LEVEL MUST
BE ABOVE TOP OF BAFFLE.
RESERVOIR CAPACITY IS ONE (1)
GALLON. DO NOT OVERFILL.
FIGURE 3.6
16
Section 3 - MAINTENANCE
ANNUALLY (END OF EACH SEASON)
(Continued from previous Page)
FUEL FILTER (DIESEL ENGINE ONLY)
Service fuel filter as instructed in engine owner's
manual. Turn key to "OFF" position. Engine MUST
be stopped and MUST be cold before removing
filter.
1. Move the fuel filter cock handle to the closed
position.
2. Remove the fuel filter bowl retaining ring. Fuel
filter bowl, two "0" Rings, spring and filter can be
removed. See Figure 3.8.
3. Replace filter element. Clean filter bowl with
fresh diesel fuel. Reassemble the fuel filter bowl
assembly. Tighten retaining ring securely. Check
for leakage. Air bleed the fuel system.
4. Fill the fuel tank to the fullest extent. Open the
fuel filter cock.
5. Loosen air vent plug a few turns at the top of
fuel filter/fuel cock assembly. Allow air bubbles to
be released. Close air vent plug when a steady flow
of fuel is observed.
NOTE: After replacing fuel filter, engine may have
to be cranked briefly with air vent plug loosened to
purge all air from system.
3.6 DECK REMOVAL
Move machine to an area where the mower
deck is to be disconnected. Turn engine "OFF"
but leave key switch in the "ON" position.
Engage parking brake.
1. The rear of deck must be raised up and both
jack stands moved down to the lowest position
and both locking pins inserted. NOTE: Jack
stands are stored on the left and right rear sides
of the mower.
2. Using deck lift switch, lower deck down to
rest on jack stands.
3. The hitch latch pins are shown in the latched
position. The latched position locks the deck lift
arm into position. See Figure 3.9.
HITCH LATCH PIN
SHOWN IN LATCHED
OR LOCKED
FUEL COCK
PLUG
_ LARGE "O"
RING
FUEL BOWL
I
• RETAINING
FIGURE 3.8
DECK _. | / ""
LIFT ARM HITCH
PLATE
FIGURE 3.9
(Continued on Next Page)
|WARNING
Allow engine to cool for at least ten minutes before
performing service or maintenance. DO NOT smoke
near fuel components when performing service or
maintenance. DO NOT perform service and
maintenance near an open flame. Wipe off any
spilled fuel before starting engine. DO NOT run
engine indoors.
17
Section 3 - MAINTENANCE
3.6 DECK REMOVAL
(Continued From Previous Page)
4. Rotate spring loaded hitch latch pins
(Located on both hitch plates) to the unlatched
position. See Figure 3.10.
5. Move deck lift switch as if to lower deck and
the lift arm will move up in the hitch plates. The
lift arm needs to be high enough to clear the
hitch plates when power unit is driven
backward away from mower deck. See Figure
3.9.
6. Pull lock collar back and slide power
transfer shaft away from power take off (PTO)
shaft. See Figure 3.11.
7. Disconnect wiring harness from mower deck.
8. Start power unit. Disengage parking brake.
Carefully move power unit backward away from
mower deck.
NOTE: DECK LIFT ARM SHOWN REMOVED FOR
CLARITY. DECK WOULD NOT BE REMOVED AT THIS
TIME IN DECK REMOVAL PROCEDURE.
HITCH LATCH PIN SHOWN IN
UNLATCHED POSITION
3.7 POWER TRANSFER SHAFT REMOVAL
Engage parking brake. Turn engine "OFF" and
remove key. The power transfer shaft connects
the power unit to the mower deck. The shaft is
telescoping for easy removal. Slide locking collar
back toward mower deck and shaft will slide off.
See Figure 3.11.
WARNING
DO NOT attempt any maintenance, adjustments or
service with engine running. STOP engine. STOP
blades. Set brake. Remove key. Remove spark plug
wires and secure away from spark plugs. Engine
and components are HOT. Avoid serious burns.
allow sufficient time for all parts to cool.
\HITCH
PLATE
FIGURE 3.10
POWER LOCK COLLAR
TRANSFER 17"
SHAFT /
PULL LOCK ,_COLLAR POWER
BACKWARDS TAKE OFF""
SHAFT
FIGURE 3.11
18
Section 4 - ADJUSTMENTS & REPAIR
DANGER
Exercise EXTREME CAUTION when making this I
adjustment, due to close proximity of moving parts. I
4.1 NEUTRAL POSITION ADJUSTMENTS
The joystick controls the movement and stopping
of the machine. Move the joystick to the center or
neutral position to stop machine. IMPORTANT:
Always return the joystick with hand assistance to
the neutral position. If machine does not come to a
complete stop or has any movement when joystick
is moved to the neutral position, adjustment must
be made.
1. Turn key to "OFF" position.
2. Raise both wheels off the ground. Wheels
should be high enough to rotate freely. Secure with
safety blocks.
3. Disconnect parking brake rod from parking
brake.
4. Engage parking brake lever. NOTE: Engaging
parking brake without brake rod connected will
lock joystick in center or neutral position.
5. Turn key to start position and start engine.
6. Both wheels should be still, not rotating.
7. If wheel(s) are rotating, disconnect
transmission control rods from cross shaft and
turn adjusting bolts located on pump(s) clockwise,
or counter-clockwise, until wheel(s) stop rotating.
See Figure 4.1.
8. With wheels in neutral, (not rotating) stop
engine and readjust the length of the control rods
until they fit into the cross shaft arms and
reconnect. Tighten securely.
9. Reconnect park brake rod.
10. Start engine. Release park brake. Wheels
should not be rotating if adjusted properly. Repeat
adjustment if necessary.
4.2
4.2.1.
MOWER DECK & COMPONENT ADJUSTMENTS
The following mower deck and component
adjustments and repairs can be made by the owner.
However, if there is difficulty in making these
adjustments and repairs, it is recommended that
these repairs be made by an authorized SNAPPER
dealer.
MOWER DECK ADJUSTMENT (LEVELNESS)
SIDE to SIDE and FRONT to REAR
Before making deck leveling adjustments, check
tires and add or release air as needed to bring
pressure to 12 psi in drive tires (Turf Type Tires), 5
psi (All Terrain Type Tires) and 25 psi in rear caster
tires. Pressure in front deck caster wheels should be
25 psi.
If tires are properly inflated and mowing is still
uneven, adjust deck levelness as follows:
1. Place mower on a smooth level surface.
2. Raise deck to highest cutting position.
3. Place 2x4 blocks under front edge of deck beside
caster wheels. Blocks should be on both sides of
deck. Make deck relatively level by positioning
blocks. Both caster wheels must be off the ground.
4. Loosen leveling bracket at center rear deck
support. See Figure 4.2. This allows the lift arm to
settle down into hitch brackets.
LOOSEN
NUTS
LEVELING BRACKET
FIGURE 4.2
ADJUSTING TRANSMISSION CONTROL ROD
TRANSMISSION
FIGURE 4.1 FIGURE 4.1A
19
Section 4 - ADJUSTMENTS & REPAIR
4.2.1. MOWER DECK ADJUSTMENT (LEVELNESS) 4.3
SIDE to SIDE and FRONT to REAR
(Continued from previous page)
5. Retighten leveling bracket bolts.
6. Remove both bolts (one from each side) from the
front portion of the link weldment. See Figure 4.3.
The front caster wheel will drop to the ground.
7. Turn ball joint in or out until ball joint anchor hole
aligns with mounting hole. Reinstall bolt and tighten
securely. Use same procedure on other caster
wheel. See Figure 4.3.
8. Reinstall bolts and tighten securely.
9. Remove blocks from under front of deck.
10. Side to Side Level: Check blade tips by
rotating blades until tips are pointing to the side of
the deck. Check the measurement of outside blade
tips to the ground on both blades. The measurement
of each outside blade tips should be within 118"of
each other.
11. Front to Rear Level: Check blade tips by
rotating blades until tips are pointing to the front and 4.5
rear of deck. Check the blade tip measurements of
each blade. Front to rear measurement should be
114"to 318"higher in the rear.
CASTER WHEEL BRACKET
//
PARKING BRAKE ADJUSTMENT
4.3.1 The park brake can be adjusted by
removing the rod from the lever and
rotating clockwise to increase brake
tension. When properly adjusted the park
brake lever should require 18 to 22 pounds
force to set the brake. If this adjustment
does not result in proper brake action,
contact your authorized Snapper dealer for
corrective action. See Figure 4.4.
I ' Oni'nw',°'°°
operate machine if brakes are t
g properly.
4.4 ENGINE ADJUSTMENTS & REPAIR
Refer to the engine owner's manual for engine
adjustments and/or repairs.
MOWER BLADE REPLACEMENT
4.5.1. BLADE WEAR LIMITS
1. Inspect blade frequently for signs of
excessive wear or damage. See Figure 4.5.
WARNING
Wear heavy leather gloves when handling or working
around cutting blades. Blades are extremely sharp
and can cause severe injury. DO NOT use a cutting
blade that shows signs of excessive wear or
damage.
ROTATE BALLJOINTIN
OR OUTTO ALIGN WITH
REMOVE HOLEIN CASTER WHEEL
BOLT BRACKET
FIGURE 4.3
WARNING
DO NOT attempt any adjustments, maintenance or
service with the engine or blades running. Stop
blades. Stop engine. Set brake. Remove key.
Remove spark plug wires from spark plugs and (gas
only) secure wires away from spark plugs. Engine
and components are HOT. Avoid serious burns by
allowing all parts sufficient time to cool.
PARKING
BRAKE
LEVER
/
ROTATE BRAKE PARKING
ROD CLOCKWISE BRAKE ROD
TO TIGHTEN
BRAKE
FIGURE 4.4
20
Section 4 - ADJUSTMENTS & REPAIR
4.5 MOWER BLADE REPLACEMENT
4.5.1. BLADE WEAR LIMITS
(Continued from previous page)
NEW BLADE
WEAR LIMIT
(NOTCH STARTS)
__......._ DANGEROUS CONDITION! MOUNTING
BOLT
BEVELED
WASHER
FIGURE 4.5
WARNING
DO NOT use acutting blade that shows signs of
excessive wear or damage. Refer to Figure 4.5. Wear
heavy leather gloves when handling or working
around cutting blades. Blades are extremely sharp
and can cause severe injury.
4.5.2. BLADE SHARPENING
1. Remove blade. See Figure 4.6.
2. Inspect condition of blade.
See Figure 4.5.
3. If blade is in good condition, sharpen at
22 to 28 degrees. DO NOT sharpen beyond
existing cutting edge.
See Figure 4.7.
4. Check blade balance after sharpening.
If necessary, correct blade balance by
grinding the heavy end of blade.
IMPORTANT: Blade balancing should be
performed by a qualified dealer.
5. Reinstall blade. See Figure 4.5. Torque
blade mounting bolts to recommended
range of 70 to 80 ft. Ibs.
DO NOT SHARPEN
BEYOND ORIGINAL
CUTTING EDGE
BLADE
FIGURE 4.6
ORIGINAL CUTTING EDGE
J
BLADE TIP
\
FIGURE 4.7
21
Section 4 - ADJUSTMENTS & REPAIR
4.6 MOWER DRIVE BELT, ENGINE BELT & HYDRO
PUMP BELT REPLACEMENT
Inspect all belts. Replace belt if it shows signs of
excessive wear, damage and/or is broken.
WARNING
DO NOT attempt any adjustments, maintenance or
service with the engine or blades running. Stop
blades. Stop engine. Set brake. Remove key.
Remove spark plug wires from spark plugs and (gas
only) secure wires away from spark plugs. Engine
and components are HOT. Avoid serious burns by
allowing all parts sufficient time to cool.
4.6.1. MOWER DRIVE BELT REMOVAL
1. Remove mower drive belt cover.
2. Remove old belt.
4.6.2. MOWER DRIVE BELT REPLACEMENT
1. Route belt around blade pulleys and idler
pulley as shown. It may be necessary to use
a pry bar to pull idler pulley back to install
belt. See Figure 4.8.
2. Reinstall belt cover.
iFRONT OF
MOWER
DISCHARGE
CHUTE NOT
SHOWN
3. Remove the nuts and bolts that secure
the metal couplings to the rubber flex
coupling. Remove rubber flex coupling to
allow space to remove and install belt.
4. Remove belt from around pulleys and
fan. Pull belt through where rubber flex
coupling was located.
5. Install new belt in reverse order.
6. Reinstall rubber flex coupling. Reinstall
alternator cover and radiator screen.
Reinstall all nuts and bolts. Tighten all nuts
and bolts securely.
RADIATOR
SCREEN
FRONT OF MOWER
REAR OF MOWER
COVER RADIATOR
SCREEN
METAL
COUPLING
FIGURE 4.8
4.6.3. ENGINE BELT REMOVAL
1. Remove radiator screen.
2. Remove nut and bolt that secure the top
portion of alternator cover, Rotate cover to
the side, See Figure 4.9.
REMOVE
RUBBER
FLEX
COUPLING
FIGURE 4.9
22
Section 4 - ADJUSTMENTS & REPAIR
4.7 BATTERY
4.7.1. BATTERY REMOVAL
1. Remove battery retainer.
2. Slide battery from battery box to gain
access to terminal cables.
3. Observe and note cable positions on
battery. See Figure 4.10.
4. Disconnect cables from battery terminals,
disconnecting BLACK (Negative) cable first,
then disconnect RED (Positive)last. Retain
mounting bolts and nuts.
WARNING I
Cables must be connected to battery terminals in the
proper position, RED (Positive) cable must go to the I
( + ) terminal, BLACK (Negative) cable must go to the I
(-) terminal, I
4.7.2. BATTERY INSTALLATION
1. Slide battery partially into battery
compartment.
2. Connect cables to battery terminals.
Connect RED (Positive) cable first. Connect
BLACK (Negative) cable last.
3. Reinstall battery retainer and positive
terminal cover.
BATTERY REMOVAL:
DISCONNECT BLACK CABLE (NEGATIVE) FIRST,
DISCONNECT RED CABLE (POSITIVE) LAST.
BATTERY INSTALLATION:
CONNECT RED CABLE (POSITIVE) FIRST,
CONNECT BLACK CABLE (NEGATIVE) LAST.
WARNING
The electrolyte (acid) produces ahighly explosive
gas. Keep all sparks, flame and fire away from area
when charging battery or when handling electrolyte
or battery. Electrolyte (acid) is ahighly corrosive
liquid. Wear eye protection. Wash affected areas
immediately after having eye or skin contact with
electrolyte (acid). Battery acid is corrosive. Rinse
empty acid containers with water and mutilate before
discarding. If acid is spilled on battery, bench, or
clothing, etc., Flush with clear water and neutralize
with baking soda.
4.7.3. BATTERY SERVICE
1. Remove battery.
2. Place battery in a well ventilated area on
a level surface.
3. Using distilled water, refill cells as
required to cover cell plates.
4. With cell caps removed, connect battery
charger to battery terminals. RED to positive
(+) terminal and BLACK to negative (-)
terminal.
5. Slow charge battery at 1 amp for 10
hours. An alternative fast charge should be
no more than 2.5 amps for four hours.
6. If battery will not accept charge or is
partially charged after 10 hours of charging
at 1 amp, replace with new battery.
(Continued on Next Page)
NEGATIVE
TERMINAL
POSITIVE
TERMINAL
\q ITERMINAL COVER MUST
ISHIELD POSITIVE
TERMINAL AFTER
INSTALLATION
FIGURE 4.10
23
Section 4 - ADJUSTMENTS & REPAIR
4.7 BATTERY
State of Charge
100% Charged w/Sulfate Stop
100% Charged
75% Charged
50% Charged
25% Charged
0% Charged
Battery Condition
Syringe Hydrometer
1.280
1.265
1.210
1.160
1.120
Less than 1.100
Chart
Digital Voltmeter
12.80v
12.60v
12.40v
12.10v
11.90v
Less than 11.80v
Five Ball Hydrometer
Five Balls Floating
Four Balls Floating
Three Balls Floating
Two Balls Floating
One Ball Floating
Zero Balls Floating
WARNING
Shield the positive terminal with terminal cover
located on battery harness. This prevents metal from
touching the positive terminal, which could over
heat battery and/or battery cable and cause sparks.
DO NOT attempt to charge battery while installed on
the Zero Turning Radius Mower. DO NOT use
"BOOST" chargers on the battery.
4.7.4. BATTERY TESTING
There are two types of battery tests:
Unloaded and Loaded. The unloaded test is
the procedure that will be discussed. It's the
simplest and most commonly used. An
unloaded test is made on a battery without
discharging current. To perform unloaded
testing, check charge condition using either
a hydrometer or voltmeter.
1. Using a voltmeter, voltage readings
appear instantly to show the state of
charge. Remember to hook the positive
lead to the battery's positive terminal, and
the negative lead to the negative terminal.
2. A hydrometer measures the specific
gravity of each cell. The specific gravity tells
the degree of charge; generally, a specific
gravity of about 1.265 to 1.280 indicates full
charge. A reading of 1.230 to 1.260
indicates the battery should be charged
before testing. The chart on the next page
shows the charge level as measured by
syringe float hydrometer, digital voltmeter
and five ball hydrometer.
4.7.5. NEW BATTERY PREPARATION
1. Remove battery from carton.
2. Place battery in a well ventilated area on a
level non-concrete surface.
WARNING
DO NOT OVERFILL!
3. Remove battery cell caps. Fill cells as
required with electrolyte (purchased
separately) to proper level. Fill to 3/16"
above cell plates. Filling battery with
electrolyte will bring the battery to 80%
charged state.
4. With cell caps removed, connect battery
charger to battery terminals; RED to positive
(+) and BLACK to negative (-) terminal.
IMPORTANT: 3/16" above cell plates is the recommended
level. DO NOT place anything in battery other than specified
electrolyte.
5. Slow charge the battery at 1 amp for 2
hours to bring the battery to full charge.
6. After charging, check level of electrolyte
and add as needed to bring level to 3/16"
above cell plates.
7. Reinstall cell caps.
8. Install battery into power unit.
9. Connect positive (+) cable (red) first,
from wiring harness to the positive terminal
(+) on battery using bolt and nut provided
in hardware bag. Connect negative (-)
cable (black) last, to negative terminal (-)
on battery using bolt and nut. Apply a small
amount of grease over terminals to prevent
corrosion.
24
Section 4 - ADJUSTMENTS & REPAIR
4.8 MOWER SPINDLES (Field Serviceable
Spindles) BEARING REPLACEMENT
In the event that a spindle bearing requires
replacement, the SNAPPER Field Serviceable
Spindles have been designed so that no special
tools or presses are required.
1. Remove belt. Loosen blade nut and remove.
Allow blade bolt, washer, blade and four spacers to
drop down out of the spindle housing. See Figure
4.11.
REMOVE NUT _. REMOVE BELT
__<=( ROMSPINDLE
"--.- ;Oo O Oo, oo
FIGURE 4.11
2. Remove spindle pulley from spindle shaft.
3. Locate circular retaining ring on spindle shaft at
top bearing. Remove retaining ring. Allow spindle
shaft to drop out of housing.
4. Top and bottom bearings are now removable.
Pull out on inner race to slide bearing from
housing. See Figure 4.12.
BEARING
SEAL UP
qp.._ PULLEY
SPINDLE _
HOUSING
i
n
INNER RACE ""_0
BEARING _ €
i ...............................
BEARING SEAL
DOWN
NOTE: The bearing is sealed/shielded on one side
only. The bottom bearing must be installed with the
sealed/shielded side DOWN.
7. Insert spindle shaft up through the bottom
bearing. Slide spacer down over spindle shaft.
8. Install new top bearing. Install the top bearing
with the seal/shield UP.
9. Slide circular retaining ring down spindle shaft
until it fully locks into groove on shaft.
10. Place spindle pulley and spacer on top of
spindle shaft.
11. Reinstall blade bolt, washer, blade and four
spacers.
12. Torque blade bolt and nut to 60 to 75 ft. Ibs.
IMPORTANT: Spindle housing must be filled
with grease before operating mower. Failure to
fill housing will cause premature bearing
failure.
13. Pump grease into spindle housing until grease
purges from vent on housing.
14. After the first 5 hours of operation, grease
spindle housing to insure it is full, then every 25
hours.
FIGURE 4.12
5. Thoroughly clean all parts removing all old
contaminated grease.
6. Install new bottom bearing first.
25
TROUBLESHOOTING
PROBLEM
Starter Will Not Crank
Engine
Engine Will Not Start
Engine Stalls After
Running
Engine Loses Power
PROBABLE CAUSE
1. Battery dead•
2. Blown fuse.
3. Electrical connections loose or corroded•
1.
2.
3.
4. Defective ignition switch• 4.
1. Blade engagement switch in the "ON" position• 1.
2. Park brake not set. 2.
3. Fuel tank empty• 3.
4. Fuel filter clogged• 4.
5. Fuel cock in the "OFF" position• 5.
6. Battery weak or dead. 6.
7. Faulty parking brake, blade or ignition switch• 7.
1. Operator not in seat. 1
2. Fuel injection nozzle clogged with carbon• 2.
3. Fuel tank empty• 3.
4. Engine air cleaner dirty• 4.
5. •Insufficient lubrication• 5.
6. Fuel filter clogged• 6.
7. Water, debris or stale fuel in fuel system• 7.
1. Excessive load on engine• 1
2. Engine air pre-cleaner or air cleaner dirty• 2.
3. Engine oil level low. 3.
4. Fuel injection nozzle clogged with carbon• 4.
5. Water, debris or stale fuel in fuel system• 5.
Engine Backfires When 1. Throttle control set too "FAST"• 1
Turned To "STOP"
Excessive Vibration 1. Damaged or bent mower blades• 1
2. Loose blade components• 2.
3. Loose or missing air lift (if equipped)• 3.
Engine Over Heats 1. Insufficient engine lubrication• 1
2. Fan belt broken or out of adjustment• 2.
3. Insufficient coolant level• 3.
4. Thermostat defective• 4.
5. Radiator screen or radiator cooling fins clogged• 5.
6. Water pump, fan & radiator cap defective• 6.
7. Incorrect fuel injection timing• 7.
8. Excessive concentration of antifreeze• 8.
9. Cooling system clogged with debris• 9.
CORRECTIVE ACTION
Service battery.
Replace fuse.
Clean and check connections for good contact•
Contact authorized SNAPPER dealer•
Move blade engagement switch to "OFF".
Set park brake•
Fill fuel tank with fresh diesel fuel.
Remove and clean fuel filter of all debris•
Move fuel cock lever to the "ON" position•
Service battery.
Contact authorized SNAPPER dealer•
Sit in operator's seat.
Clean or replace fuel injection nozzle•
Fill with fuel to proper level•
Clean air cleaner of all debris•
Check engine oil lubricating system•
Remove and clean fuel filter of all debris•
Drain and clean fuel system•
Lessen load.
Clean or replace filters•
Fill with engine oil to proper level•
Clean or replace fuel injection nozzle•
Drain and clean fuel system•
Set throttle control to "SLOW" and allow engine
to idle. Then, turn key to "OFF".
Service mower blade(s).
Service and tighten loose parts•
Replace air lifts• Tighten to proper torque•
Check engine oil lubrication system•
Replace fan belt or adjust to proper tension•
Check coolant level and replenish supply•
Replace thermostat of correct heat range•
Clean all debris from radiator screen and fins.
Replace cooling system parts that are defective•
Contact authorized SNAPPER dealer•
Change coolant(water/antifreeze) mixture ratio•
Drain and flush cooling system•
(Trouble Shooting Continued on Next Page)
26
TROUBLESHOOTING
PROBLEM PROBABLE CAUSE CORRECTIVE ACTION
Tractor Will Not Move 1. Joystick in the neutral "N" position. 1. Place joystick in desired speed position.
Loss Of Traction 2. Roll release lever is in "ROLL" position. 2. Move roll release lever to the engaged position.
3. Low transmission hydraulic oil level. 3. Bring hydraulic oil to proper level.
4. Parking Brake engaged. 4. Move parking brake to disengaged position.
5. Traction drive belt requires replacement. 5. Replace traction drive belt.
Blade(s) Not Cutting 1. Blade engagement switch in the "OFF" position. 1. Move blade switch to the "ON" position.
2. Clutch belt slipping. 2. Replace clutch belt.
3. Mower belt slipping. 3. Replace mower belt.
4. Electric clutch not functioning. 4. Contact authorized SNAPPER dealer.
5. Check gearbox for damage. 5. Contact authorized SNAPPER dealer.
6. Power transfer shaft disconnected or damaged. 6. Connect power transfer shaft or repair damage.
Cutting Grass 1. Uneven tire pressure. 1. Bring to proper pressure.
Improperly 2. Cutting height too low or high. 2. Adjust cutting height.
3. Engine speed too slow. 3. Move throttle control to "FAST" position.
4. Forward speed too fast. 4. Move joystick to a slower speed.
5. Terraced cut, side to side. 5. Adjust side to side level.
6. Excessive deck pitch, front to rear. 6. Adjust front to rear level.
7. Cutting blade(s) dull or damaged. 7. Sharpen cutting edges or replace blade(s).
8. Blade belt slipping. 8. Replace blade belt.
9. Check electric clutch. 9. Adjust to proper specifications.
10. Check clutch belt. 10. Replace clutch belt.
11. Check gearbox for damage. 11. Contact authorized SNAPPER dealer.
Poor Grass Discharge 1. Engine speed too slow. 1. Move throttle control to "FAST" position.
2. Forward speed too fast. 2. Move joystick to a slower speed.
3. Grass is wet. 3. Mow when grass is dry.
4. Excessively worn or damaged blade(s). 4. Service mower blade(s).
5. Build up of grass clippings and debris under deck. 5. Clean deck.
6. Improper blade(s) installed on deck. 6. Install proper SNAPPER blades.
7. Blade(s) installed improperly on deck. 7. Install blades properly.
Battery Will Not Charge 1. Poor cable connections. 1. Clean cables and battery terminals.
2. Bad battery cell(s). 2. Replace with new battery.
3. Faulty alternator. 3. Contact engine manufacturer's dealer.
Oil Leaking 1. Loose or missing hydraulic reservoir cap. 1. Check oil level and replace reservoir cap.
2. Leaking hose fittings, clamps or reservoir. 2. Verify fittings and hose clamps are tight.
Deck Will Not Lift 1. Loose or disconnected electrical harness. 1. Connect electrical harness.
Properly 2. Electric screw jack malfunctioning. 2. Contact authorized SNAPPER dealer.
3. Key switch is in "OFF" position. 3. Turn key switch to "ON" position.
27
SERVICE SCHEDULE
ITEM
Engine Oil
SERVICE PERFORMED REF.
Check Oil Level Page 9
Initial Oil Change Page 15
Periodic Oil Change Page 14
EACH 5 25
USE HRS HRS
X
50 75 100
HRS HRS HRS
X
X*
Change Oil Filter Engine Manual X
Air Cleaner Clean or Replace Engine Manual
Fuel Filter Replace Page 17
Engine Cooling Clean Radiator Screen & Engine Manual
System Fins & Page 15
Engine Cooling Check coolant level Engine Manual
System & Page 15
Battery Check Electrolyte Page 23-24
Charge Battery Page 23-24
Testing Battery Pages 24
Tires Check Air Pressure Page 9
Drive Belts Check For Wear And Page 15
Tension
Mower Blades Check For Wear, Damage Pages 14,
& Replacement 20-21
Mower Deck Clean Outside & Underside Page 15
of Debris Accumulation
Lubrication Grease or Oil Pages 15-16
Points
Hydrostatic Check Oil Level Page 16
Trans. Oil
Hydrostatic Replace Filter Page 16
Trans. Filter
X
X
X
X**
X**
X
X
X
X
X
X
First Change at 200 Hours.
Thereafter every 500 Hours.
*Change oil every 25 hours when operating under heavy toad or high temperatures.
** Clean more often under dusty conditions or when air debris is present.
MAINTENANCE PARTS
4.8.1. MAINTENANCE/REPLACEMENT PARTS
MAINTENANCE PARTS
Mower Blades (52" Deck) (Hi Lift) 2-9246 (3)
Mower Blades (61" Deck) (Low Lift) 1-7081 (3)
Mower Blades (61" Deck) (Hi Lift) 2-9251 (3)
Mower Deck Belt (52" Deck) 4-2776
Mower Deck Belt (61" Deck) 3-5542
Upper Drive Shaft To Hydro Pump Belt 3-5544 (2)
Deck Drive Shaft To Electric Clutch Belt 4-1830 (2)
Battery 3-5610
EACH
SEASON
X
X
X
X
X
X
X
X
X
28
2 YEAR LIMITED WARRANTY
For two (2) years from purchase date for the original purchaser's use, SNAPPER, through any authorized
SNAPPER dealer will replace, free of charge (except for taxes where applicable), any part or parts found upon
examination by the factory at McDonough, Georgia, to be defective in material or workmanship or both.
SNAPPER FIELD SERVICEABLE SPINDLES and their components used on SNAPPER PRO ® Mid Size walks
and SNAPPERZRIDER ® ride on commercial equipment have a three (3) year limited warranty against defects in
material or workmanship or both.
All transportation costs incurred by the purchaser in submitting material to an authorized SNAPPER dealer for
replacement under this warranty must be paid by the purchaser.
This warranty does not apply to engines and their components, and batteries, as these items are warranted
separately. This warranty does not apply to parts that have been damaged by accident, alteration, abuse,
improper lubrication, normal wear, or other cause beyond the control of SNAPPER. This warranty does not
cover any machine or component that has been altered or modified, changing safety, performance, or durability.
Batteries have a one (1) year prorated warranty period with free replacement if required during the first ninety
(90) days from the original purchase date. SNAPPER will not be responsible for any installation cost incurred.
The battery warranty only covers original equipment batteries and does not cover damage to the battery or
machine caused by neglect or abuse, destruction by fire, explosion, freezing, overcharging, improper
maintenance, or use of improper electrolyte.
There is no other express warranty.
DISCLAIMER OF WARRANTY
Implied warranties, including those of merchantability and fitness for a particular purpose, are limited to
two (2) years from purchase date for the original purchaser's use, and up to the extent permitted by law
and all implied warranties are excluded. This is the exclusive remedy. Liabilities for consequential
damages, under any and all warranties are excluded.
Some states do not allow limitations on how long an implied warranty lasts, or do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may
not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
WARNING: THE USE OF REPLACEMENT PARTS OTHER THAN GENUINE SNAPPER PARTS MAY IMPAIR THE
SAFETY OF SNAPPER PRODUCTS AND WILL VOID ANY LIABILITY AND WARRANTY BY SNAPPER ASSOCIATED
WITH THE USE OF SUCH PARTS.
IMPORTANT: Please fill out the attached SNAPPER Product Registration Card immediately and mail to:
Snapper's Product Registration Center, P.O. Box 1379, McDonough, Georgia. 30253
29
NOTES
30
NOTES
31
Safety Instructions & Operator's Manual for
OUT FRONT Z-RIDER
HYDRO DRIVE
SERIES 0
®
IMPORTANT
Snapper products are built using engines that meet or exceed all applicable emissions requirements on the
date manufactured. The labels on those engines contain very important emissions information and critical
safety warnings. Read, Understand, and Follow all warnings and instructions in this manual, the engine
manual, and on the machine, engine and attachments. If you have any questions about your Snapper product,
contact your local authorized Snapper dealer or contact Snapper Customer Service at Snapper, McDonough,
GA. 30253. Phone: (1-800-935-2967).
I_LWARNING: The engine exhaust from this product contains chemicals known to the State I
of California to cause cancer, birth defects or other reproductive harm. I
SNAPPER McDonough, GA., 30253 U.S.A.
COPYRIGHT © 2001
SNAPPER INC.
ALL RIGHTS RESERVED
32
INSTRUCTION No. 7-4370 (I.R. 4/6/01)

Navigation menu