SOUNDMAX ELECTRONICS MGR Car radio User Manual

Soundmax Electronics Limited Car radio

User Manual

BLUETOOTH® (Audio Streaming)Marine Gauge Digital Media AM/FM ReceiverMGR450BUSER MANUALFEATURING ZERO STANDBY CURRENT DRAINQUICK INSTALLATION GUIDEMGR450BUSER MANUAL QUICK INSTALLATION GUIDEBLUETOOTH® MARINE GAUGE DIGITAL MEDIA AM/FM RECEIVERPRINTED IN CHINAVER:1.0 EN0417BOSS Audio Systems3451 Lunar Court • Oxnard, CA 93030www.bossaudio.com800-999-1236 US Toll-free805-751-4853 Customer Servicetech support: www.bossaudio.com/support/technical-supportThe Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks is under license. Other trademarks and trade names are those of theirrespective owners.BEFORE YOU STARTIMPORTANT SAFETY PRECAUTIONSBE SURE TO OBSERVE THE FOLLOWING GUIDELINES:• Do not turn up the volume so high that you can’t hear what’s around you.• Use caution or temporarily discontinue use in potentially hazardous situations. • Do not operate mobile video equipment while driving a motorized vehicle – safe driving and safety consideration of others should always be your highest priority.• Set your volume control at a low setting, then slowly increase the sound until you can hear it comfortably without distortion, or ear discomfort.• In the event you should notice smoke, strange noises or odor from this product, or any other abnormal signs, immediately turn off the power and consult your dealer or the nearest authorized BOSS AUDIO Service Center Using this product in this condition may result in permanent damage to the system.WIRE DIAGRAMThank you for purchasing this MGR450B Bluetooth Marine Gauge Digital Media AM/FM ReceiverPlease read thorough these instructionscarefully so you will know how to operate your model properly. After you have nished reading the instructions, keep this document in a safe place for future reference. SUGGESTED MOUNTING METHODSINFORMATION TO THE USERTROUBLESHOOTING GUIDE!! WARNING !!ADJUSTMENT OR ALTERATIONS OF THIS DEVICE MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. THIS PACKAGE CONTAINSTo avoid potential shorts in the electrical system, be sure to disconnect the (–) battery cable before installation. Use this unit with a 12-Volt battery and negative grounding only. Failure to do so may result in a re or malfunction.When replacing the fuse, be sure to only use a fuse of the rating specied on this product. To avoid short-circuiting, cover any disconnected leads with insulating tape. It is specially impor-tant to insulate any unused wires, which if left uncovered may cause a short circuit. When connecting other devices to this product, refer to the manual for the product to be connected. The black cable is ground, make sure to connect the ground wire rst.Ensure that the ground cable is properly connected to metal parts of the vehicles body frame or direct to the battery if your vehicle does not have a grounded chassis frame. The ground cable of this units power amp and a second powered system must be connected to the frame separately with different screws. If the screw for the ground wire loosens or falls out, it could result in re or malfunction. CAUTION!! Do not ground or short the speaker leads 1-805-751-4853www.bossaudio.com/supportTECHNICAL SUPPORT This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device.This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. The Bluetooth antenna cannot be removed (or replaced) by user. This equipment complies with FCC/ IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation (MPE). But it is desirable that it should be installed and operated keeping the radiator at least 20 cm or more away from person’s body (excluding extremities: hands, wrists, feet and ankles). Alteration or modications carried out without appropriate authorization may invalidate the user’s right to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Relocate or reorient the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.FCC COMPLIANCE STATEMENT132TROUBLE CAUSE SOLUTIONUnit will not turn onThe fuse is blown Check / replace the fuseIgnition not engaged Turn ignition to on positionNo sound is heardBlown speaker Replace faulty speakerVolume is low / muted Press the volume level upDevice is paused or mutedCheck your devices playing / volume statusCannot pair Bluetooth The Bluetooth function of the device is not enabledRefer to the user manual of thedevice for how to enable theBluetooth functionThe MGR450B BT memory is fullFollow how to reconnect a device in section EThe audio quality is poor after connection with a Bluetooth enabled device The Bluetooth reception is poorMove the device closer to theaudio system or remove anyobstacle between the device and the systems antennaUnit has becomeunresponsivePower glitch or interferenceDisconnect power for 10 seconds to resetLow battery powerCharge battery, run the engine to recharge the batteryReset the main system Follow steps in section BINSTALLATION PRECAUTIONSAlways consult with a professional installer• Do not attempt to install or service this product by yourself. Installation or servicing of this product by persons without professional training and experience in electronic equipment and mo-torized vehicle accessories may be dangerous and could expose you to the risk of electric shock, injury or other hazards• Refer any repairs to a qualied BOSS AUDIO SYSTEMS Service Center• The MGR450B should be wired directly to a vehicles battery • When wiring directly to the vehicles battery, be sure to disconnect the batteries negative terminal wire before starting any wiring procedures, if extending the main power primary wire, it is suggested that an optional fuse and fuse holder (not included) with minimum rating of 20 Amperes be in-line with the positive battery terminal • The ground cable length should be as short as possible, if extending from you battery, be sure to use a proper gauge rating for the length of the run, use only high quality copper primary type wire• The MGR450B has a IPX6 weather resistant design, it should not be submerged in or under water under any circumstances• Do not use abrasive cleaning materials on the lens or bezel• Use only the installation parts provided with the MGR450BTOOLS NEEDED:- Measuring Tape / Ruler - Wrench and/or Pliers- Hole Saw- Crimp Tool CAUTION!!Using other mounting methods may void this warranty FM TUNER FREQUENCY RANGE• USA 87.5~107.9MHz• Europe 87.5~108MHz• Asia 87.5~108MHz• Australia 87.5~108MHz• Usable Sensitivity: 12dB (S/N=30dB)• Bands: 2AM TUNER FREQUENCY RANGE• USA 530~1710KHz• Europe 522~1620KHz• Asia 522~1620KHz • Australia 522~1620KHz• Usable Sensitivity: 40dB (S/N=20dB)• Bands: 1WEATHER BAND SELECTION • CH.1 162.400MHz • CH.2 162.425MHz • CH.3 162.450MHz• CH.4 162.475MHz• CH.5 162.500MHz• CH.6 162.525MHz• CH.7 162.550MHz• Bands: 1 BLUETOOTH• BT: 3.0 • BT Range: 33Ft / 10M (Class 2) • BT Proles: A2DP / AVRCP 1.3 USB DRIVE MEDIA SUPPORTED• MP3• WMA• 65,000 Songs• 32GB / FAT 32• USB 2.0 High Speed• USB Output Voltage: 5VDC @ 1AINTEGRATED AMPLIFIER • MOSFET• MAX Continuous Output: 240W (All channels driven)• PEAK Power Rating: 60W / channel • Channels: 4• Class: AB• Frequency Response: 20-20kHz• 4Ω stableCHASSIS• Button Backlight Illumination: BLUE LED• F/R/S RCA Preamp Output: 2VRMS • RCA Input Impedance: 10kΩ• LCD: TN Type / Active MatrixGENERAL• Power Source: 14.4VDC(10.8V ~ 16V allowable)• Grounding System: Negative type• Maximum Current Consumption: 15A• 3-way protection circuitry (thermal, overload, and speaker short protection) • Unit Weight: 1.08lbs / 0.52kg • Storage Temperature: -22oF to 176oF / -30oC to 80oC• Operation Temperature: -4oF to 158oF / -20oC to 70oC• Replacement Fuse: 15A (Replace with AGU Fuse Type Only)SPECIFICATIONSSpecications subject to change without noticeQUICK START GUIDEFOR CHARGING ONLY: Cell Phone and iPodMedia Playback Not SupportediPod® and iPhone® are registered trademarks of Apple Inc.registered in the USA and other countries.BOSS Audio Systems is not afliated with Apple Inc.Copyright © 2017 FCC Radiation Exposure StatementThis equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body
AUDIOxBass On/OffMID LevelTreble LevelBalance LevelFader LevelAUDIOShort PressVOLVOLVOLVOLVOLVOLVOLVOLVOLVOLVOLVOLAUDIOLong PressVOLVOLEQBASS Level SYSTEMAUDIOVOLVOLSubwoofer SettingsVOLVOLVOLVOLBLUETOOTH OPERATIONBLUETOOTH STREAMING MUSICPAIRING & DISCOVERING A NEW BLUETOOTH CONNECTIONNote: The mobile device must be within 33ft (10m) of the MGR450B for Bluetooth to function properly.1) Power on the MGR450B by pressing and holding down the Power button for 1 second, the Bluetooth ICON will start to ash signalling that the MGR450B is now ready for Bluetooth pairing. NOTE: You have 2 minutes before you must restart this procedure over again.2) Now that the MGR450B is in pairing mode:ANDROID users: a. Go into the Settings Menu of your ANDROID device b. Enter the Bluetooth Menu and press SCAN c. “Boss Audio MGR450B” will now be display under AVAILABLE DEVICES d. If prompted, enter passcode: “0000”iOS users: a. Go into the Settings Menu of your iOS device b. Enter the Bluetooth Menu c. “Boss Audio MGR450B” will now be displayed d. If prompted, enter passcode: “0000”3) If the MGR450B is not seen, repeat the above steps to refresh the “Device List” 4) When the BT connection is successful you will see BT CONNECTED message on the MGR450B LCD display, you are now ready to stream music from your devices favorite media player to the MGR450BRECONNECTION1) Power on the MGR450B and your last paired device Bluetooth2) The unit will now automatically be reconnected3) If your device was previously paired with the MGR450B, but it wasn’t the last paired device: a. Ensure no other devices are currently paired b. Press and hold MENU button to manually connect / reconnect to the MGR450B4) If the device is out of range from the MGR450B, it will disconnect automatically: 5)The MGR450B will reconnect to the device once in range, a conrmation message will be displayed on the LCDAUX-INPUT1) Press the SRC button to select BT AUDIO2) Press to start PLAY, press again to PAUSE3) To skip songs or advance tracks press VOLVOL, press and hold to FAST FORWARD4) To select the previous track press the button VOLVOL, press and hold to FAST REWIND5) Press the button to display song ID3 information1) Press the SRC button to select AUX IN2) Press to MUTE, press again to UNMUTE Ensure to adjust the level of your devices master volume to 75%Tips: ENNyne Cruiser USB CHARGE5V 1AUSB OPERATIONRADIO OPERATION1) Press the SRC button to select USB2) Press to start PLAY, press again to PAUSE3) To skip songs or advance tracks press VOLVOL, press and hold to FAST FORWARD4) To select the previous track press VOLVOL, press and hold to FAST REWIND5) Press the button to display song ID3 information1) Press the SRC button to select RADIO2) Press to MUTE, press again to UNMUTE3) To advance stations press VOLVOL4) To skip previous stations press VOLVOL5) Press the button to display RADIO information6) Press the PRESET button to recall PRESETS 1 ~ 6BTSUBWSYSTEMBEEPSUBWSYSTEMBEEP ONSUBWBEEPBT000000SUBWLOCALSUBWSUBWSYSTEMLOCALSUBWSUBWFUNCLOC ONSUBWLOCALSUBWLOCALLOC OFFSUBWLOCALSUBWLOCALBT000000SUBWLOCALSUBWSUBWSYSTEMP6 10350SUBWLOCALRADIOMY SONGSSUBWBTTITLESUBWUSBSUBWAUX-INBTSUBWSYSTEMBEEPSUBWSYSTEMBEEP ONSUBWBEEPBT000000SUBWLOCALSUBWSUBWSYSTEMLOCALSUBWSUBWFUNCLOC ONSUBWLOCALSUBWLOCALLOC OFFSUBWLOCALSUBWLOCALBT000000SUBWLOCALSUBWSUBWSYSTEMP6 10350SUBWLOCALRADIOMY SONGSSUBWBTTITLESUBWUSBSUBWAUX-INBTSUBWSYSTEMBEEPSUBWSYSTEMBEEP ONSUBWBEEPBT000000SUBWLOCALSUBWSUBWSYSTEMLOCALSUBWSUBWFUNCLOC ONSUBWLOCALSUBWLOCALLOC OFFSUBWLOCALSUBWLOCALBT000000SUBWLOCALSUBWSUBWSYSTEMP6 10350SUBWLOCALRADIOMY SONGSSUBWBTTITLESUBWUSBSUBWAUX-INBTSUBWSYSTEMBEEPSUBWSYSTEMBEEP ONSUBWBEEPBT000000SUBWLOCALSUBWSUBWSYSTEMLOCALSUBWSUBWFUNCLOC ONSUBWLOCALSUBWLOCALLOC OFFSUBWLOCALSUBWLOCALBT000000SUBWLOCALSUBWSUBWSYSTEMP6 10350SUBWLOCALRADIOMY SONGSSUBWBTTITLESUBWUSBSUBWAUX-INGETTING STARTEDTips: ENNyne Cruiser USB CHARGE5V 1ATips: ENNyne Cruiser USB CHARGE5V 1ATUNER SETUPBTSUBWSYSTEMBEEPSUBWSYSTEMBEEP ONSUBWBEEPBT000000SUBWLOCALSUBWSUBWSYSTEMLOCALSUBWSUBWFUNCLOC ONSUBWLOCALSUBWLOCALLOC OFFSUBWLOCALSUBWLOCALBT000000SUBWLOCALSUBWSUBWSYSTEMP6 10350SUBWLOCALRADIOMY SONGSSUBWBTTITLESUBWUSBSUBWAUX-INBTSUBWSYSTEMBEEPSUBWSYSTEMBEEP ONSUBWBEEPBT000000SUBWLOCALSUBWSUBWSYSTEMLOCALSUBWSUBWFUNCLOC ONSUBWLOCALSUBWLOCALLOC OFFSUBWLOCALSUBWLOCALBT000000SUBWLOCALSUBWSUBWSYSTEMP6 10350SUBWLOCALRADIOMY SONGSSUBWBTTITLESUBWUSBSUBWAUX-INABDEFGHOPERATION QUICK START GUIDE \ \ \ \ \ \ \ \ \ \ \ \ \ \ \ \BTSUBWSYSTEMBEEPSUBWSYSTEMBEEP ONSUBWBEEPBT000000SUBWLOCALSUBWSUBWSYSTEMLOCALSUBWSUBWFUNCLOC ONSUBWLOCALSUBWLOCALLOC OFFSUBWLOCALSUBWLOCALBT000000SUBWLOCALSUBWSUBWSYSTEMP6 10350SUBWLOCALRADIOMY SONGSSUBWBTTITLESUBWUSBSUBWAUX-INBTSUBWSYSTEMBEEPSUBWSYSTEMBEEP ONSUBWBEEPBT000000SUBWLOCALSUBWSUBWSYSTEMLOCALSUBWSUBWFUNCLOC ONSUBWLOCALSUBWLOCALLOC OFFSUBWLOCALSUBWLOCALBT000000SUBWLOCALSUBWSUBWSYSTEMP6 10350SUBWLOCALRADIOMY SONGSSUBWBTTITLESUBWUSBSUBWAUX-INBTSUBWSYSTEMBEEPSUBWSYSTEMBEEP ONSUBWBEEPBT000000SUBWLOCALSUBWSUBWSYSTEMLOCALSUBWSUBWFUNCLOC ONSUBWLOCALSUBWLOCALLOC OFFSUBWLOCALSUBWLOCALBT000000SUBWLOCALSUBWSUBWSYSTEMP6 10350SUBWLOCALRADIOMY SONGSSUBWBTTITLESUBWUSBSUBWAUX-INBTSUBWSYSTEMBEEPSUBWSYSTEMBEEP ONSUBWBEEPBT000000SUBWLOCALSUBWSUBWSYSTEMLOCALSUBWSUBWFUNCLOC ONSUBWLOCALSUBWLOCALLOC OFFSUBWLOCALSUBWLOCALBT000000SUBWLOCALSUBWSUBWSYSTEMP6 10350SUBWLOCALRADIOMY SONGSSUBWBTTITLESUBWUSBSUBWAUX-INEN \ \ \ \AUDIO and SYSTEM SETUPCSOURCE MODESAll rights reserved. No part of this publication may be reproduced, distributed, or transmitted in any form or by any means, including photocopying, recording, or other electronic or mechanical methods, without the prior written permission of BOSS AUDIO SYSTEMS Inc. To avoid battery exhaustion be sure to run the vehicles engine while using this product. Using this product without running the engine can drain the battery.Tips: ENNyne Cruiser USB CHARGE5V 1A

Navigation menu