Spectrum 4502003ZIG OHM Zigbee V.2 User Manual 13 954 Comcast Users Guide 5066485

Spectrum Brands, Inc. OHM Zigbee V.2 13 954 Comcast Users Guide 5066485

Users Manual - 954

AK or L (2x)K LNMAABBBABIf drilling a new door, use the supplied template and the complete door drilling instructions available at www.kwikset.com/doorprep.Note: Additional door preparation may be required for doors with 11/2" (38 mm) holes. Consult the deadbolt drilling instructions at www.kwikset.com/doorprep.orbacksetMeasure to conirm that the hole in the door is either 21/8" (54 mm) or 11/2" (38 mm).Measure to conirm that the backset is either 23/8" or 23/4" (60 or 70 mm).23/8" or 23/4"60 or 70 mm 13/8" –2"35 – 51 mmMeasure to conirm that the hole in the door edge is 1" (25 mm).Measure to conirm that the door is between 13/8" and 2" (35 mm and 51 mm) thick.AA BCDB C DIs the door edge chiseled?Is the D-shaped hole centered in the door hole?Which latch are you installing?Hold the latch in front of the door hole, with the latch face lush against the door edge.21/8"54 mm11/2"38 mm1"25 mmYESYESNONOUse latch “A”. If the latch bolt is not already extended, extend the latch bolt as shown.No adjustment is required. Proceed to next step.D-shaped hole D-shaped holeRotate latch face as shown to extend latch.wood blockactual sizeUse latch “B” (not included). If the latch bolt is not already extended, extend the latch bolt as shown.Latch “A” Latch “B”N (2x) CM (2x)Longer screws install closest to the door jamb.door frameEInstall strike on the door frame. Make sure the hole in the door frame is drilled a minimum of 1" (25 mm) deep.orchiseled not chiseledor1Prepare the door and check dimensions2Install the latch and strikeorLatch“B” is not included. If needed, please contact Kwikset to order a drive-in latch for your lock.StrikeCABExterior TouchscreenAdapter RingDMounting PlateParts in the boxFasteners03809 46780KMNL64109U49191TFE6484364845QS64844R(1-3/8" • 35 mm)(2" • 51 mm)(1-3/4" • 44 mm)BatteriesInterior AssemblyGHJVRequired toolsRulerHammer Wood blockPhillips head screwdriverAdditional Tools (depending on application)1 / 4ENGLISH66485002Rev 03 954ZigBeeInstallation and User GuideKwikset Technical Support1-866-863-6584www.kwikset.com
21/8"54 mm11/2"38 mmWhat is the thickness of your door?Use the shorter gold screws.Use the medium silver screws.1-3/8" (35 mm) 1-3/4" (44 mm) 2" (51 mm)Use the longer black screws.or or1-3/8"35 mm1-3/4"44 mm2"51 mmQ R S2 / 4What is the diameter of the hole in the door?ABCDiameter is 2-1/8" (54 mm)Diameter is 1-1/2"(38 mm)or“D” is required for installation. Install “D” on “F”.“D” is not needed for installation. Discard “D”.Remove battery cover and battery pack from interior assembly. Install interior assembly onto mounting plate.A BacbMake sure turnpiece is in the vertical position.HHThis step will teach your lock the orientation of your door and is crucial to lock operation.Install 4 AA batteries in battery pack. Make sure the door is open, and insert the battery pack.After a few seconds, the latch bolt will retract and extend on its own to learn the orientation of the door. This is called the door handing process, and it is crucial to lock operation.If the touchscreen indicates a failure make sure that the cables are connected, the batteries are installed correctly, and attempt this procedure again.If the door handing process is still unsuccessful after a second attempt, perform the “Manual Door Handing” procedure on page 4.A B CD Ensure correct polarity. For best results, use new, non-rechargeable Alkaline batteries only.Ensure tight cable connection.Lay excess cable lat inside the bottom of the interior housing.alignJacbdT(2x)Tactual sizebottom holeJGJH4Install the interior assembly5Install the batteries and perform the door handing processDo not install batteries until step 5.Once the door handing process is complete, the touchscreen will indicate success or failure:Success:lashing checkmark symbol and single column of digitsFailure:lashing “X” patternCable goes underneath latch. Support exterior assembly during mounting plate installation.Insert the tip of a Phillips screwdriver into the torque blade. screwsKeep parallel to edge of door.Tighten screws evenly.acbdextendedMake sure the latch bolt is fully extended.Apply slight pressure while rotating the torque blade to test for smooth latch operation. Route cable through center hole, then push cable into bottom hole. If the latch does not retract and extend smoothly, adjust the mounting screws.FQ, R, or S (2x)EeInstall exterior touchscreen and mounting plate.VDDFactual sizeQ (1-3/8" / 35 mm)R (1-3/4" / 44 mm)S (2" / 51 mm)3Install the exterior touchscreen
1x 3xwindow3 / 4Conirm that the code(s) added in previous step can unlock the door.Checkmark symbol with one beepOption 1Touch screen with palm or back of hand until digits illuminate.Option 2Touch lower left area of screen (where checkmark is located) until digits illuminate.Option 3Touch screen with three or more ingers until digits illuminate.“X” pattern with three beepsorMake sure the door is open. Press the Program button once.Activating the Screen Locking the Door Unlocking the Door SecureScreen™Press checkmark symbol once.Enter user code. A total of 30 user codes may be programmed.Press lock symbol once.A B C DWhat digits and sounds did the lock produce?EProgramming Timeout During programming, if the screen is not pressed for 20 seconds, the system will time out (indicated by three beeps and the “X” pattern lashing three times), and you will need to restart the procedure.It is recommended that you add and delete all user codes through your smart home control system. If your system does not allow this, codes may be added directly to the lock as shown here.Programming was successful. Programming was unsuccessful. Make sure the user code is not a duplicate and that it is between 4 and 8 digits during your next attempt. Make sure the lock has room for an additional code. If all user code positions are illed, delete a code to make room for this one.1. Activate the screen.2. Press Lock symbol. Note: If no user codes are programmed, the door cannot be locked via touchscreen.1. Activate the screen.2. If SecureScreen is enabled, touch the random digits that appear.3. Enter user code. If you press the wrong digit while entering a user code, you can press the Lock symbol once to clear the digits entered previously and immediately restart the code entry process.If desired, this feature can be disabled by turning switch #4 to the o position. See “Switches and Status LED Colors” on page 4.SecureScreen is an added-security feature that displays random digits before you enter a user code to unlock the door. This feature ensures that there are ingerprints on all digits so that codes cannot be identiied by examining the touchscreen for inger prints.Each user code must be a unique code between 4 and 8 digits, depending on your smart home system.*Beeping sound will only be heard if switch #3 (on the lock interior) is in the on positon. See “Switches and Status LED Colors” on page 4.MastercodeFor enhanced security, a mastercode may be used when adding and deleting user codes. For more information about the mastercode, download the Programming and Troubleshooting Guide on the Obsidian page at www.kwikset.com.678Add the lock to your smart home systemInitiate the process to add the lock to your system at your smart home controller. Refer to your smart home system instructions for more information. When prompted by your smart home system to add the lock, press button “A” on the lock interior four times. If successful, re-name the lock in your system (if applicable).If unsuccessful, press button "B" nine times.Perform steps 6A6C again.If still unsuccessful, consult the Programming and Troubleshooting Guide on the Obsidian page at www.kwikset.com.A B CDbutton “A” button “B”U (3x)UIf you wish to unlock the window, you can slide it up for more convenient access to the programming buttons while the cover is installed.To unlock the window, remove the security screw.The window on the interior cover is locked by default to prevent someone from tampering with your lock's settings.Important Information about the interior coverCover InstallationInstall cover.turnpiece shaftInstall screws.abInstall the interior coveractual sizeGNote: You may need to rotate the turnpiece to align with the turnpiece shaft.Note: The interior cover and screws must be removed for battery pack access.turnpiece9Add user codes (30 max)Test the lock (review normal operation)
Display Alert Reason Solution“X” pattern lashes one time with one beep*. One incorrect code entered. Re-enter code.“X” pattern lashes three times with three beeps*.No user code programmed. Program at least one user code.Programming timeout after 20 seconds. Attempt programming procedure again.Unsuccessful programming.“X” pattern lashes 15 times with 15 beeps*Three incorrect codes entered within one minute.Re-enter code after 60 second touchscreen lockout.Checkmark and lock symbols lash simultaneously ive times with long continuous beep*.Low battery. Replace batteries.Checkmark and lock symbols alternate lashing ive times with long continuous beep*.Door jammed while attempting to lock.Manually re-lock door. If needed, reposition strike.N/A Lock beeps continuously. Interior assembly is disconnected from exterior.Remove battery pack, reconnect the interior to the exterior, then replace battery pack.Status LEDIf the touchscreen indicates a failure, see the online Programming and Troubleshooting Guide or call Technical Support.Note: All codes may be deleted at once if the mastercode is enabled. For more information about the mastercode, consult the online Programming and Troubleshooting Guide.© 2017 Spectrum Brands, Inc.ExteriorTouchscreenCheckmark symbolLock symbolEmergency Power 9 Volt PortSuccess Failure4 / 4Obsidian at a Glance System AlertsSwitches and Status LED ColorsDeleting a single user code Factory Reset*Beeping sound will only be heard if switch #3 is on.If the screen is not pressed for 20 seconds, the system will time out, and you will need to restart the procedure.A factory reset will delete all codes associated with the lock, and it will remove it from your smart home system.1. Read all instructions in their entirety.2. Familiarize yourself with all warning and caution statements.3. Remind all family members of safety precautions.4. Protect your user codes and mastercode. 5. Dispose of used batteries according to local laws and regulations. CAUTION: Prevent unauthorized entry. Since anyone with access to the back panel can change the user codes, you must restrict access to the back panel and routinely check the user codes to ensure they have not been altered without your knowledge. The use of a mastercode can help protect your system’s settings. WARNING: This Manufacturer advises that no lock can provide complete security by itself. This lock may be defeated by forcible or technical means, or evaded by entry elsewhere on the property. No lock can substitute for caution, awareness of your environment, and common sense. Builder’s hardware is available in multiple performance grades to suit the application. In order to enhance security and reduce risk, you should consult a qualiied locksmith or other security professional.Switch Function1 Door lock status LED blinks every 6 seconds2Lock automatically re-locks door 30 seconds after unlocking. Disabled if no codes are programmed.3 Audio4SecureScreen feature displays random digits to be pressed before entering user code. This added-security feature ensures that there are ingerprints on all digits so that codes cannot be identiied by examining the touchscreen for ingerprints.Color Lock StatusBlinking green UnlockedBlinking amber LockedBlinking red Low batteryReference GuideImportant SafeguardsBack panelButton “A”Program buttonStatus LEDSwitchesButton “B”Turnpiece shaftNote: When the cover is removed, the turnpiece shaft can be used to manually lock and unlock the door.If needed, the door handing process can be initiated manually. This is useful if the lock is being moved to a dierent door.Interior (cover removed)1 2 3 4OnSwitchesStatus LEDOManual Door Handing3 Press the Program button once more. 4 The latch bolt will extend and retract to learn the orientation of the door.1 Remove battery pack.2 Press and HOLD the Program button while reinserting the battery pack. Release button once battery pack is installed. The status LED will lash red and green.Status LED1 Remove battery pack.3 Press the Program button once more. The status LED will lash green and red several times.2 Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for 30 seconds until the lock beeps and the status LED lashes red.4 After a few seconds, the lock will initiate the door handing process, and the latch bolt will extend and retract to learn the orientation of the door.Removing the lock from the networkPress button "B" on the lock interior nine times.1 Keep door open. Press Program button once.2 Press Checkmark symbol once.3 Press Lock symbol once.4 Enter user code to be deleted.5 Press Lock symbol once.6 Re-enter user code. 7 Press Lock symbol once.If unsuccessfulMake sure to enter the same valid code in steps 4 and 6.Test codeWhile the door is open, test the user code to make sure it no longer unlocks the door.Network InformationLow BatteryIf the 4 AA batteries are too low to operate the lock, use a 9Volt Alkaline battery to temporarily power the touchscreen. Make sure both terminals on the 9Volt battery touch the terminals at the bottom of the touchscreen. Hold the 9Volt in place while entering your user code to unlock the door. Continue holding the 9Volt in position until the Checkmark symbol illuminates and the door unlocks.Note: If you remove the battery before the Checkmark symbol illuminates, you will need to re-enter your user codeZigBee System NotesZibee is a "Wireless mesh network", and results may vary based on building construction and communication path with 36+ feet being typical installed distance in a standard home environment and 250+ feet when the lock has a clear line of sight with the smart home controller. It may be necessary to install additional Zigbee devices to enhance the communication path between the lock and controller for a more robust ZigBee network.

Navigation menu