Spotwave Wireless SPOTCELL0014 Uplink Booster User Manual SpotCell 2500Xe
Spotwave Wireless Ltd. Uplink Booster SpotCell 2500Xe
Contents
- 1. manual
- 2. User Manual
manual
![](/img.php?id=570497&img=bg1.png)
®
SpotCell 2500 User ManualXe
![](/img.php?id=570497&img=bg2.png)
![](/img.php?id=570497&img=bg3.png)
Technical Support
SpotCell® serial numbers must be available to authorize technical support and/or to establish a
return authorization for defective units. The serial numbers are located on the back of the Coverage
Unit (CU) and the Donor Unit (DU), as well as on the box in which they were delivered. Additional
support information may be obtained by accessing the Spotwave Wireless Inc. website at
www.spotwave.com. To contact support by telephone, call your local Spotwave vendor; or if you
are
unable to reach your vendor, contact Spotwave Wireless at
866-704-9750
.
Important Safety Information
Warning! For your safety, beware of power lines and ensure appropriate safety measures are
maintained at all times during the installation of the SpotCell equipment. If equipment not shipped
with the SpotCell system is to be used during installation or mounting, follow all equipment
manufacturer’s instructions in proper use to ensure injury is avoided.
The DU and CU of the SpotCell are low power transmitters. As with a cell phone antenna, avoid
unneccessary contact with the front of the units when they units are operating. Mount the units in a
location where people will not approach within 1 meter of the front of the DU and 20 centimeters in
front of the CU.
When deploying the extended coverage antenna, there must be a minimum separation of 10 cm
between the main CU and the extended coverage antenna with the antennas facing in opposite
directions. The extended coverage antenna should be mounted in locations where people will not
approach within 20 cm in front of the antenna.
This manual outlines installation instructions and the appendix offers practical safety tips (see
Appendix E entitled ‘Safety Hints’).
If you are not sure about a safe installation, do not attempt to install it yourself. Call a professional
installer for help.
LIMITED WARRANTY AND LIMITATION OF LIABILITY:
1. What is Covered and for How Long? Spotwave Wireless Inc. ("Spotwave") warrants to the original Purchaser that the Spotwave SpotCell System (the
"System") is free from defects in material and workmanship under normal use and service for a period of 12 months from the date of shipment from Spotwave
(the "Limited Warranty Period").
2. What is not covered? This Limited Warranty is conditioned upon proper use of the System by the Purchaser. This Limited Warranty does not cover (and
will become null and void in the event of): (a) defects or damage resulting from accident, misuse, abuse, neglect, unusual physical, electrical or
electromechanical stress, modification of the System or any part thereof, or cosmetic damage; (b) removal, alteration or defacing of the serial number or other
identifying marks on the System; (c) all plastic surfaces and other externally exposed components that are scratched or damaged due to normal use; (d)
malfunctions resulting from the use of the System in conjunction with accessories, products or (ancillary) or peripheral equipment not provided by Spotwave;
or (e) defects or damage from unauthorized or improper testing, operation, maintenance, installation, servicing or adjustment of the System. Any repairs or
replacements provided by Spotwave outside of the Limited Warranty Period (including repairs to or replacement after the end of the Warranty Period), or in
excess of the services provided during the Limited Warranty Period, will subject to Spotwave's then prevailing rates.
3. What are Spotwave's Obligations and how do you make a claim? During the Limited Warranty Period, Spotwave will repair or replace, at Spotwave's sole
option, without charge to Purchaser, any defective component of the System, provided that the System is returned promptly upon discovery of the defect
and during the Limited Warranty Period. To obtain service, Systems must be returned to an authorized service facility in the original packaging or packaging
adequate for shipping, accompanied by Purchaser's sales receipt or comparable substitute proof of sale showing the date of purchase and the serial number
of the System. A valid RMA is required prior to any return.
To locate your nearest authorized service facility, call Spotwave Customer Service at 1-866-704-9750. Spotwave may, at Spotwave's sole option, use rebuilt,
reconditioned, or new parts or components when repairing any System or replace a System with a rebuilt, reconditioned or new System. Repaired Systems
![](/img.php?id=570497&img=bg4.png)
LIMITED WARRANTY AND LIMITATION OF LIABILITY:
ii SpotCell® Enterprise
will be warranted for a period equal to the remainder of the original Limited Warranty Period for the original System or for 90 days,
whichever is longer. All replaced parts, components, boards or equipment shall become the property of Spotwave. If Spotwave
determines that any System is not covered by this Limited Warranty, Purchaser must pay the costs for all parts, shipping, and labor charges
for the repair or return of such System.
4. What are the Limits on Spotwave's Liability? EXCEPT FOR THE WARRANTY IN PARAGRAPH 1, THE SYSTEMS AND ANY
ASSOCIATED SERVICES ARE PROVIDED BY SPOTWAVE ON AS 'AS IS' BASIS AND THERE ARE NO OTHER REPRESENTATIONS,
WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, WRITTEN OR ORAL, ARISING BY STATUTE, OPERATION OF LAW, COURSE
OF DEALING, USAGE OF TRADE OR OTHERWISE, REGARDING THEM OR ANY OTHER PRODUCT OR SERVICE PROVIDED
HEREUNDER OR IN CONNECTION HEREWITH BY SPOTWAVE. SPOTWAVE DISCLAIMS ANY IMPLIED WARRANTIES OR CONDITIONS
OF DURABILITY, MERCHANT ABILITY, MERCHANTABLE QUALITY, SATISFACTORY QUALITY, NON-INFRINGEMENT OR FITNESS FOR
A PARTICULAR PURPOSE. SPOTWAVE DOES NOT REPRESENT OR WARRANT THAT THE SYSTEMS WILL MEET ANY OR ALL OF
PURCHASERS' PARTICULAR REQUIREMENTS, THAT THE SYSTEMS WILL OPERATE ERROR-FREE OR UNINTERRUPTED OR THAT
ALL ERRORS OR DEFECTS IN THE SYSTEMS CAN BE FOUND TO BE CORRECTED. System performance is dependant upon the
performance and availability of services or technology provided by third parties and Spotwave is not responsible for service continuity and
reliability, reception, or other performance related limitations associated with use of the Systems. NO AGREEMENTS VARYING OR
EXTENDING THE TERMS OF THIS LIMITED WARRANTY WILL BE BINDING ON SPOTWAVE UNLESS IN WRITING AND SIGNED BY AN
AUTHORIZED SIGNING OFFICER OF SPOTWAVE THIS LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE
ORIGINAL PURCHASER OF THE SYSTEM. SPOTWAVE'S MAXIMUM AGGREGATE LIABILITY TO PURCHASER SHALL NOT EXCEED
THE AMOUNTS PAID BY PURCHASER FOR THE SYSTEM GIVING RISE TO THE CLAIM. SPOTWAVE SHALL NOT BE LIABLE FOR ANY
SPECIAL, INCIDENTAL, CONSEQUENTIAL, INDIRECT OR SIMILAR DAMAGES, LOSS OF USE, DATA OR PROFITS, DAMAGES TO
PURCHASER'S PROPERTY, OR INJURY TO PURCHASER OR OTHERS ARISING OUT OF THE USE, MISUSE OR INABILITY TO USE
ANY SYSTEM, WHETHER OR NOT SUCH DAMAGE ARISES OUT OF CONTRACT OR TORT (INCLUDING WITHOUT LIMITATION,
NEGLIGENCE) OR CLAIMS BY A THIRD PARTY, EVEN IF SPOTWAVE HAS BEEN ADVISED OF SUCH DAMAGES OR THEY ARE
FORESEEABLE
5. This Limited Warranty allocates risk between Purchaser and Spotwave, and the Spotwave System pricing reflects this allocation of risk
and the limitations of liability contained in this Limited Warranty. The agents, employees, distributors, dealers or representative of Spotwave
are not authorized to make modifications to this Limited Warranty, or make additional warranties binding on Spotwave. Accordingly,
additional statements such as advertising or presentations, whether oral or written, do not constitute warranties by Spotwave and should
not be relied upon.
OWNERSHIP AND RISK OF LOSS:
6. Who Owns the rights in the System? The System is protected by Canadian, US and international copyright law and other intellectual
property protection laws and treaties. Purchaser acknowledges that Spotwave and its licensors are the owner of all intellectual property,
including, without limitation, patents and copyright,
relating to the System and the trademarks used in association with the System. Purchaser agrees that it will not (and will not attempt to)
modify, prepare derivative works of, reverse engineer, decompile, disassemble, or other attempt to derive the source code of any software
contained within the System.
7. Who bears the Risk of Loss? Risk of loss for the System passes to Purchaser upon the delivery to Purchaser or to a carrier for
shipment, which ever is earlier. Title to the Systems (excluding any software) will pass upon payment in full for the Systems. Title to any
software shall always remain with Spotwave or its licensors. As security for payment, Purchaser grants to Spotwave a purchase money
security interest in the Systems (together with any proceeds, including insurance proceeds) and agrees that a copy of this letter of
agreement or any other appropriate document may be registered as required to perfect the security interest granted. Systems may be
resold by Purchaser in normal course of business, but until paid for in full, Purchaser will not pledge or otherwise encumber the Systems.
Purchaser agrees to immediately report to Spotwave, any seizure or attachment of the Systems by creditors; (ii) any petition in bankruptcy,
insolvency, receivership or similar proceedings filed by, or against Purchaser; or (iii) any arrangement, composition or similar agreement for
the benefit of creditors. Systems held for Purchaser by Spotwave are at Purchaser's sole risk and expense.
OTHER TERMS:
8. What terms govern our relationship? These terms and any software license or warranty documentation accompanying the Systems
constitute the complete and exclusive statement of the terms and conditions between us regarding the Systems and cannot be altered,
amended or modified except in writing executed by Spotwave. This letter of agreement and any disputes arising hereunder shall be
governed by and interpreted in accordance with the laws of the Province of Ontario, Canada. The United Nations Convention on Contracts
for the International Sale of Goods and any legislation implementing such Convention, if otherwise applicable is expressly excluded. Any
terms and conditions of any purchase order or other instrument issued by Purchaser which are in addition to or inconsistent with the terms
and conditions of this letter of agreement shall not be binding and shall not apply, even if accepted by Spotwave.
MANUAL DISCLAIMER
Product specifications, pricing, packaging, technical support and information ("Specifications") and all claims, features, representations,
and/or comparisons provided are correct to the best of our knowledge of the date of publication, but may contain errors or omissions and
are subject to change without notice.
INFORMATION IS PROVIDED BY SPOTWAVE WIRELESS INC. ON AN "AS IS" BASIS, WITHOUT ANY OTHER WARRANTIES OR
CONDITIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, WARRANTIES OF MERCHANTABLE QUALITY,
SATISFACTORY QUALITY, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, OR THOSE ARISING BY LAW, STATUTE,
USAGE OF TRADE, COURSE OF DEALING OR OTHERWISE. THE ENTIRE RISK AS TO THE RESULTS OF THE INFORMATION
PROVIDED IS ASSUMED BY YOU. WE SHALL HAVE NO LIABILITY TO YOU OR ANY OTHER PERSON OR ENTITY FOR ANY INDIRECT,
INCIDENTAL, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER, INCLUDING, BUT NOT LIMITED TO, LOSS OF REVENUE OR
PROFIT, LOST OR DAMAGED DATA OR OTHER COMMERCIAL OR ECONOMIC LOSS, EVEN IF WE HAVE BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES, OR THEY ARE FORESEEABLE. WE ARE ALSO NOT RESPONSIBLE FOR CLAIMS BY A THIRD
PARTY. OUR MAXIMUM AGGREGATE LIABILITY TO YOU AND THAT OF OUR DEALERS AND SUPPLIERS SHALL NOT EXCEED
FOURTY DOLLARS. SOME STATES/COUNTRIES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR
CONSEQUENTIAL OR INCIDENTAL DAMAGES, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. All product, font and company
names are trademarks or registered trademarks of their respective owners.
![](/img.php?id=570497&img=bg5.png)
RETURN POLICY
SpotCell® Enterprise iii
Return Policy
Prior to purchasing a SpotCell Enterprise system you agree to the terms indicating that
your cell phone or other wireless device does work within 50ft of the coverage problem
spot. If this requirement is met, you have the option to return the system for a refund
once we provide you with a Return Materials Authorization Number (RMA Number). You
(the customer) are responsible for shipping costs incurred for a return for refund. Product
will only be refunded if it is not damaged, contains all components, and is returned within
30 days of purchase.
For returns related to repairs within the 1 year warranty period, you can return the
coverage and donor units and power supply to Spotwave at your expense, (via a ground
shipping account that we will provide you) referencing a Spotwave RMA Number from
Customer Service & Support. Our policy is to repair or replace within 20 working days of
receipt of system, and return the system to you with the following exception:
If for some reason you receive a product that is not functioning at all (or dead on arrival),
Spotwave will advance replace the product (at no charge to you) once you provide us
with a waybill or tracking number of the original product which is being returned.
You will be charged for returned product which is found to be damaged.
If during a return for repair or replacement you choose to use your own shipper as
opposed to the Spotwave shipping account provided, Spotwave will not reimburse for
incurred shipping costs.
![](/img.php?id=570497&img=bg6.png)
iv
![](/img.php?id=570497&img=bg7.png)
SpotCell Enterprise v
Technical Support/
Important Safety Information . . . . . . . . . . . . . . . . . . . i
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Packing List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Choosing a location for the DU . . . . . . . . . . . . . . 11
Choosing a location for the CU . . . . . . . . . . . . . . 15
Positioning the Auxiliary CU . . . . . . . . . . . . . . . . . 18
Mounting the DU and CU . . . . . . . . . . . . . . . . . . . . . 19
Mounting the DU . . . . . . . . . . . . . . . . . . . . . . . . . 19
Mounting the CU . . . . . . . . . . . . . . . . . . . . . . . . . 25
Using the Hidden Cable kit . . . . . . . . . . . . . . . . . 27
Trouble-Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
2500Xe System Specifications . . . . . . . . . . . . . . . . . 33
CU indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
DU signal level indicators: . . . . . . . . . . . . . . . . . . 35
Antenna Specifications: . . . . . . . . . . . . . . . . . . . . 36
Architecture (Dual Band 850/1900) . . . . . . . . . . .37
FCC Declaration of Conformity/
Health and Authorization for Use . . . . . . . . . . . . . . . 39
Table of Contents
![](/img.php?id=570497&img=bg8.png)
vi SpotCell Enterprise
![](/img.php?id=570497&img=bg9.png)
Spotwave Wireless Inc. 1
1 – Introduction
1.1 This Manual
The contents of this manual complements the SpotCell 2500Xe Quick Install Guide. It
provides specific details that may be referred to if necessary during installation of a
SpotCell® 2500Xe adaptive coverage system.
1.2 No Special Knowledge
Installation of the SpotCell 2500Xe does not require any specialized technical knowledge.
The SpotCell coverage system can be installed by any person(s) with the ability to use a
screwdriver, and in some situations may require the use of a ladder, drill, and additional
related tools.
1.3 SpotCell 2500Xe at a Glance
The purpose of the SpotCell system is to enable personal wireless communications in
specific locations within a wireless service area where cell phones do not work, or work
poorly, for example inside a building, or at the cell boundary.
![](/img.php?id=570497&img=bga.png)
INTRODUCTION
2SpotCell® 2500Xe
The SpotCell 2500Xe system receives signals from one or more wireless base stations
and re-transmits the signal to areas where cell phones do not work or work poorly due
to obstructions or the remoteness of the location.
Figure 1.1: SpotCell 2500Xe in-building coverage
The basic SpotCell 2500Xe system is comprised of a Donor Unit (DU), a Coverage Unit
(CU) and a power supply. The DU is the outward facing part of the system that
communicates with the base station. The DU is connected (via coaxial cable) to the CU
which provides wireless coverage to indoor areas.
The SpotCell 2500Xe adaptive system is capable of dual band and split band coverage
and provides band-selective, on-frequency, in-building coverage in the cellular and PCS
bands. It uses proprietary, patent-pending, adaptive techniques that allow a SpotCell
solution to be installed and operated without engineering intervention or support.
DU
CUs
![](/img.php?id=570497&img=bgb.png)
INTRODUCTION
SpotCell® 2500Xe 3
1.3.1 The Donor Unit (DU)
The DU has an F-type coaxial port on the bottom and indicators for showing received
signal strength and system status on the back.
Figure 1.2: Bottom view of DU and connectors
Note: The SpotCell 2500Xe system includes a 2 meter (6 foot) RG6 cable which is
shipped already attached to the coaxial connector on the bottom of the DU.
Figure 1.3: Back view of DU
F connector
Signal
strength
Status
light
![](/img.php?id=570497&img=bgc.png)
INTRODUCTION
4SpotCell® 2500Xe
1.3.2 The Coverage Unit
The CU has two F-type coaxial ports, a power adapter port and indicators for showing
coverage level and system status.
Figure 1.4: CU with cover removed
Figure 1.5: Top view of CU and connectors
Coverage
level
Status
light
CU CU cover
F connector
Power
F connector
to DU
to auxiliary CU
adapter
port
![](/img.php?id=570497&img=bgd.png)
INTRODUCTION
SpotCell® 2500Xe 5
The SpotCell 2500Xe is generally format specific - CDMA/1xRTT/1xEVDO and
TDMA/GSM/GPRS/EDGE formats. When ordering a SpotCell solution be sure to specify
the format, frequency band and sub-band. For PCS band equipment it is helpful if the
start and stop frequencies for the operational sub-band are provided.
1.3.3 SpotCell 2500Xe Configurations
The basic SpotCell 2500Xe system configuration is one DU connected with a coaxial
cable to a CU which is connected to an AC adapter that supplies power to both units.
Figure 1.6: Basic SpotCell 2500Xe configuration
With the Hidden Cable kit, a BIAS-T (power inserter) can be used to discreetly power the
system or power the system from a more conveniently located AC outlet.
Figure 1.7: SpotCell 2500Xe configured with BIAS-T
![](/img.php?id=570497&img=bge.png)
INTRODUCTION
6SpotCell® 2500Xe
To expand the coverage area, a second CU can also be added to the system.
Figure 1.8: SpotCell 2500Xe configured with second Coverage Unit
WIth a second CU in the system, one or two BIAS-T (power inserters) from the Hidden
Cable kit can be used. The BIAS-T can be located between the DU and CU, between
the two CUs, or both.
Figure 1.9: BIAS-T installed between DU and CU
Figure 1.10: BIAS-T installed between main CU and auxiliary CU
![](/img.php?id=570497&img=bgf.png)
Spotwave Wireless Inc. 7
2 – Installation
2.1 Preparation
The following are general considerations and preparations that should be looked at
before installing the SpotCell 2500Xe system.
2.1.1 Signal Strength
The SpotCell 2500Xe system brings signals from an area of adequate coverage to an
area with poor or non-existent coverage. It is the DU which captures a good signal, and
the CU that provides the signal to the area with poor cell phone coverage. The DU can
be mounted inside or outside, as long as it is in an area where your cell phone works.
Generally, the better your cell phone works at the location the DU is mounted, the better
the system will perform.
2.1.2 DU Height
In fringe areas, locating the DU as high as possible will provide optimal performance.
2.1.3 Avoid obstructions
General placement of the DU and CU must be in unobstructed areas. For example, the
CU should not be placed on a wall behind any type of furniture (behind items such as
metal filing cabinets would be a particularly poor location). Similarly for the DU, the front
of the unit should not be directly facing any type of metal structures, which are often
found on building rooftops.
![](/img.php?id=570497&img=bg10.png)
INSTALLATION
8SpotCell® 2500Xe
2.1.4 Proximity to power source
The indoor unit (CU) must be located within 20 feet (6 meters) of a power source, unless
the Hidden Cable kit is used. This kit includes a BIAS-T (power inserter) that allows the
system to be powered from a AC outlet located within 20 feet (6 meters) anywhere along
the coaxial cable.
2.1.5 Distance between DU and CU
Although you should separate the DU and CU as much as possible, the maximum
length of RG-6 cable that can be used to connect the two units is 164 feet (50 meters).
For greater DU to CU separation, RG-11 double shielded cable can be used to connect
the two units. Using RG-11 cable extends the maximum DU to CU distance to 328 feet
(100 meters).
Plenum rated RG-6 and RG-11 cable may also be used for installations in return air
ceilings, floor to floor riser use and elevator shafts. The maximum Plenum cable lengths
that can be used are 147 feet (45 meters) for RG-6 and 295 feet (90 meters) for RG-11.
Make sure the general location of the two units is within these limits. Use only Spotwave
Wireless approved cable.
Note: Although you should separate the DU and CU as much as possible, there is no
minimum cable length required between units for the SpotCell 2500Xe system.
2.1.6 Distance between main CU and auxiliary CU
The maximum cable lengths that can be used to connect two CUs is the same as that
for connecting a CU and DU (see Table 1). Maximum separation of the CUs and back-
to-back positioning will optimize system performance.
2.1.7 Orientation of DU relative to CU
If possible face the DU and CU in opposite directions, and back to back while
maintaining maximum separation. While not a requirement, some installations will
perform better if the units are positioned in this manner. This is generally more important
for an inside mounted DU than one mounted outside on a roof or an external wall.
non-Plenum Plenum
RG-6 164 ft (50 m) 147 ft (45 m)
RG-11 328 ft (100m) 295 ft (90 m)
Table 1: Maximum cable length for connecting units
![](/img.php?id=570497&img=bg11.png)
INSTALLATION
SpotCell® 2500Xe 9
2.1.8 Barrier between DU and CU
The greater the physical obstruction between the DU and CU, the better the
performance. Dense obstructions such as brick, concrete or metal walls are better than
wooden or plaster walls.
2.2 Packing List
This section describes the components that ship with the SpotCell 2500Xe system and
the available options.
2.2.1 SpotCell 2500Xe
The SpotCell 2500Xe solution is shipped with the following components:
Donor Unit (DU) - this is the outward facing part of the system.
Coverage Unit (CU) - this is the indoor part of the system.
Power Adapter - to be plugged into an electrical outlet and connected to the CU.
Mounting Kit - for mounting the DU and CU
Quick Installation Guide
Figure 2.1: SpotCell 2500Xe kit
CU
DU
Power
Supply
Install
Guide
![](/img.php?id=570497&img=bg12.png)
INSTALLATION
10 SpotCell® 2500Xe
2.2.2 SpotCell 2500Xe Auxiliary CU
The SpotCell 2500Xe Auxiliary CU kit is shipped with the following components:
Auxiliary CU - this is the second indoor part of the system.
Power Adapter - to be plugged into an electrical outlet and connected to the CU.
Mounting kit
Figure 2.2: SpotCell 2500Xe Auxiliary CU kit
Note: The coaxial cable needed to connect the CU to the DU can either be ordered from
Spotwave Wireless or can be supplied by the installer.
2.2.3 Hidden Cable Kit
The Hidden Cable kit makes it easier to hide the RF and power cables that are normally
connect directly to the CU.
The Hidden Cable kit is shipped with the following components:
90º F connectors (2)
BIAS-T (power inserter)
Figure 2.3: Hidden Cable kit
The BIAS-T (power inserter) is for indoor use only and cannot be installed outdoors.
2.2.4 Outdoor Self-Install Kit
The parts that are supplied with a standard SpotCell 2500Xe system are for indoor
installation and do not cover all possibilities. Additional hardware required to mount the
DU outside is provided in the optional Outdoor Self-Installation kit. This kit includes items
such as extra angle mounts, cable and a grounding block.
CU
Power
Supply
![](/img.php?id=570497&img=bg13.png)
INSTALLATION
SpotCell® 2500Xe 11
Note: You may also need to purchase additional hardware specific to your mounting
environment (such as a non-penetrating roof mount) before you begin the installation.
2.2.5 Unpacking the Equipment
Physically inspect the box for shipping damage before unpacking the SpotCell System.
1. Remove the SpotCell 2500Xe components from the box.
2. Remove all packing material from the Donor Unit (DU) and the Coverage Unit (CU).
Save the packaging in case the system is ever stored or shipped for service.
3. Check the contents of the package to make sure you have received everything
ordered and the kits contains all the listed parts.
Check the DU and CU for shipping damage. Pay particular attention to the unit’s outer
shell casing.The standard SpotCell 2500Xe system can provide up to 10,000 square
feet of coverage.
2.3 Choosing a location for the DU
The DU is the outward facing unit. It is the unit that picks up the signal from and
communicates with the service providers basestation network.
It may not be possible to install the DU indoors when installing the SpotCell solution in
remote areas. An effort should be made to install the DU outdoors and the DU should be
installed as high as possible when the installation is in a remote area.
Use your mobile phone handset to identify the inside location of the strongest received
signal, or the outside roof or external wall location where the strongest signal is received.
2.3.1 Positioning the DU
The following outlines the procedure for locating a DU inside a building, on a rooftop,
and on the outside surface of an external wall.
1. Position the DU (but do not mount it) as close to the final desired mounting location
as possible.
Indoors Outside on a Roof Outside on an External
Wall
While not a requirement, it is highly
recommended the DU be installed 3
to 4 feet away from the glass when
facing a windowa.
a. Tinted windows may contain metallic particles which can degrade the radio signal more than
the adjacent exterior wall.
The CU should not be brought outdoors if it is
raining, below freezing or above 105 Fo (40 Co).
![](/img.php?id=570497&img=bg14.png)
INSTALLATION
12 SpotCell® 2500Xe
2. Temporarily connect the DU to the port labeled on the top of the CU with
copper core coax cable. The 6 ft (2 m) cable already attached to the DU can used to
make this temporary connection.
Figure 2.4: Temporarily connect CU to DU
3. Connect the power supply to the CU and plug the power supply adapter into a wall
socket.
Figure 2.5: Connect power to CU
Note: Only use the power supply provided with the SpotCell 2500Xe system.
Connecting a power supply from another SpotCell system may damage the unit and
cause it to fail.
![](/img.php?id=570497&img=bg15.png)
INSTALLATION
SpotCell® 2500Xe 13
4. Alignment. Hold the DU upright and pointing away from you, while:
Monitor the number of bars displayed on the signal strength indicator during the
rotation. The number of bars is an indication of the signal strength the DU is receiving
from the wireless basestation.
Figure 2.6: Signal strength indicator on back of DU
Note the direction the DU is facing when the greatest number of bars is displayed,
this is the direction the DU must face when it is mounted. When multiple locations
Indoor DU Outdoor DU On a Roof Outdoor DU on an External
Wall
Rotating the DU left to right
with the DU facing to the
outside through the window
or exterior wall.
If not in front of a window,
rotate the DU in a complete
360° circle.
Rotating the DU in a
complete 360° circle.
Rotating the DU left to
right with the DU facing
away from the exterior
wall.
Window or Exterior Wall
Exterior Wall
![](/img.php?id=570497&img=bg16.png)
INSTALLATION
14 SpotCell® 2500Xe
show the same greatest number of bars, mount the DU facing in the direction where
the number of bars was displayed for the longest period of time during rotation.
5. It is recommended that various outside roof and exterior wall locations, and locations
within the building be tested to identify the best DU location. On the upper floors of
tall buildings, it may be necessary to tilt the DU down to get the strongest signal.
The bar display on the DU will help you identify the location where the received signal
strength is strongest. See DU signal level indicators: on page 35 for details on the
signal level indicator.
Mount the DU in the location that has the highest indicated signal level. Five bars is
maximum.
Note: The displays on the DU automatically shut off after the system has been powered
for 20 minutes. If this time-out occurs during the location or allignment of the DU, simply
re-activate the display by either cycling the system power off/on or disconnecting and
re-connecting the DU’s coaxial cable.
6. Proceed to mounting the DU and installing the coaxial cable (see “Mounting the DU
on page 19”).
After the DU is mounted, it is recommended that you temporarily re-connect the CU
to the DU and quickly verify that the expected greatest number of bars (as found in
steps 4 and 5) is displayed.
![](/img.php?id=570497&img=bg17.png)
INSTALLATION
SpotCell® 2500Xe 15
2.4 Choosing a location for the CU
The CU location is optimized, after the DU location and orientation have been optimized,
the DU has been mounted, and the copper core coaxial cable has been pulled from the
DU to the location requiring improved coverage.
Generally, the CU should be mounted in a location as far as possible from the DU, while
being within the area where you require improved coverage and within reach of the
maximum allowed cable length (see Table 1 on page 8)
If mounted on a wall, the coverage pattern for an open area with minimum obstructing
walls is as shown in Figure 2.7.
Figure 2.7: Coverage pattern in front of CU
When mounting the CU on a ceiling, the unit should be positioned in the middle of the
area to be covered side-to-side, and off-centered front-to-back. Figure 2.8 shows the
coverage area when the CU is mounted closer to the center of room or if mounted on a
typical interior drywall partition. The back coverage area is reduced further if the partition
wall is constructed of a dense material such as concrete or brick.
Figure 2.8: Back and front coverage pattern
![](/img.php?id=570497&img=bg18.png)
INSTALLATION
16 SpotCell® 2500Xe
The unit should be mounted as high on the wall as possible.
Note: The CU is designed to be mounted only in
a vertical orientation. Do not mount the CU
horizontally as this may cause the unit to exceed
its normal operating temperature.
2.4.1 Positioning the CU
Before positioning the CU, ensure that the DU position has been optimized and the DU
has been mounted in place.
To position the CU
1. Place the CU in the area needing coverage, but do not physically mount at this time.
2. Temporarily connect the cable from the DU to the port labelled on the top of
the CU.
Figure 2.9: Connect CU to DU
3. Connect the power supply to the CU, and then plug the adapter into an AC outlet.
![](/img.php?id=570497&img=bg19.png)
INSTALLATION
SpotCell® 2500Xe 17
4. Hold the CU in the position it is to be mounted. Ideally the display on the back of the
CU will show 5 bars for coverage area.
Figure 2.10: Coverage display on CU
If it is not showing 5 bars for coverage area and there are alternate mounting
locations, move the CU to the alternate locations and check the display. Place the
CU in the location showing maximum number of bars.
See CU indicators on page 33 for more information on the CU Coverage Indicator.
5. If the number of bars is not changing, which is very possible, choose a CU mounting
location that is convenient for the area requiring coverage.
6. Once the CU is positioned for optimal coverage, permanently run the copper core
coaxial cable from the DU to the CU locatrion. See Routing the cable and Bringing
the cable indoors on page 22.
7. Tighten the cable connection to the CU with a wrench (a 1/4 of a turn tighter than
finger tight) to ensure moisture does not penetrate.
8. Refer to Mounting the CU on page 25 for mounting instructions.
![](/img.php?id=570497&img=bg1a.png)
INSTALLATION
18 SpotCell® 2500Xe
2.5 Positioning the Auxiliary CU
The Auxiliary CU should be optimized and mounted after the MAIN CU has been
optimized and mounted. The guidelines for positioning the Auxiliary CU are the same as
those for mounting the MAIN CU.
mount the Auxiliary CU in a location as far as possible from the DU, while being
within the area where you require improved coverage.
the Auxiliary CU should be positioned in the middle of the coverage area, side-to-
side, and off-centered slightly front-to-back, approximately as shown in Figure 2.8.
the Auxiliary CU should be mounted as high on the wall as possible.
To position the Auxiliary CU
1. Temporarily connect the port labelled on the auxiliary CU to the port labelled
on the main CU.
2. Connect the extra power supply to the Auxiliary CU and plug the adapter into an AC
outlet.
3. Hold the Auxiliary CU in the position it is to be mounted. In an ideal application, the
display on the CU will show 5 bars of coverage area. If the display is not showing 5
bars for coverage area and there are alternate possible mounting locations, move
the Auxiliary CU to the alternate locations and check the display.
4. Place the Auxiliary CU in the location showing maximum number of bars. In the
event the number of bars is not changing, which is very possible, choose a location
that is most convenient.
5. Once the Auxiliary CU is positioned for optimal coverage, permanently run the
copper core coaxial cable from the MAIN CU to the Auxiliary CU locatrion.
6. Refer to Mounting the CU on page 25 for mounting instructions.
Main CUAuxiliary CU
![](/img.php?id=570497&img=bg1b.png)
Spotwave Wireless Inc. 19
3 – Mounting the DU and CU
Mount the DU and CU only after the optimal locations for each unit has been determined
(see 2.3“Choosing a location for the DU” and 2.4“Choosing a location for the CU”).
3.1 Mounting the DU
The DU may be indoor or outdoor mounted. Based on the direction the DU will point,
consider possible mounting locations.
The basic hardware required for mounting the DU on internal walls is included in the
SpotCell 2500Xe mounting kit. The hardware required for mounting the DU outside is
included in the optional Outdoor Mounting kit. The illustrations on the following pages
show some of the possible mounting options.
3.1.1 Mounting Options
Overhead Mount
The overhead mount provides left to right rotation, but
no up or down-tilt.
![](/img.php?id=570497&img=bg1c.png)
MOUNTING THE DU AND CU
20 SpotCell® 2500Xe
Wall Mount
The wall mount configuration allows for some left to
right rotation, but no up or down tilt.
The second bracket required for this mounting
configuration is provided with the optional Outdoor
Mounting kit.
Side Surface Mount (indoor only)
The side surface mount allows for some up and
down tilt, but no left to right rotation.
There are two important concerns with this
mounting configuration:
1. This configuration cannot withstand strong winds
and should only be used indoors.
2. To keep the bracket secure, all four mounting
nuts on the back of the DU must be in place and
tightened, even if only two of the nuts are holding
the bracket to the DU.
Pipe Mount
Use U-bolts to mount the unit to a 2-in pipe.
The pipe mount allows for complete left to right
rotation with no range of up-tilt or down-tilt.
![](/img.php?id=570497&img=bg1d.png)
MOUNTING THE DU AND CU
SpotCell® 2500Xe 21
Extended Vertical Surface Mount
This configuration can be used to mount the DU from an
overhead vertical surface (such as a beam or truss) and
allows for full rotation either left to right or up and down,
depending on how the mount is fastened to the DU.
The second bracket required for this mounting
configuration is provided with the optional Outdoor
Mounting kit.
3.1.2 DU Outdoor Mounting
The mounting bracket has holes, keyhole slots, and rounded slots for 1/4-in lag bolts.
Mounting to a wood structure
1. Use the holes in mounting bracket as a template and mark the hole locations.
2. Drill 1/8-in. diameter holes approximately 2.5-in. deep.
3. Install the DU mounting bracket using at least two 1/4-in. lag bolts.
4. Fasten the DU to the mounting bracket.
Mounting to a brick or concrete structure:
1. Use holes in mounting bracket as a template and mark the hole locations.
2. Use a masonry drill bit to drill 5/16-in. diameter holes, 2-in. deep.
3. Insert masonry screw anchors so that the anchor is flush to the mounting surface.
4. Install the DU mounting bracket using at least two 1/4" lag bolts.
5. Fasten the DU to the mounting bracket.
![](/img.php?id=570497&img=bg1e.png)
MOUNTING THE DU AND CU
22 SpotCell® 2500Xe
Mounting to a pipe:
1. Fasten the bracket to the DU before mounting to the pipe.
2. Feed the u-bolts (from the Outdoor Install kit) through the rounded rectangular slots
as shown in “Use U-bolts to mount the unit to a 2-in pipe.”.
3. Aim the DU at the signal source and tighten the u-bolts.
Note: DO NOT use cable ties to mount the DU.
Routing the cable
When routing the cable on a roof be sure to locate it where it will not be tripped over.
Use tie-wraps to attach the cable to an existing pipe or cable run.
Figure 3.1: Cable Strap
Secure the cable to wood or siding walls using #6 x 1.5-in. wood screws and cable loop
straps as shown in Figure 3.1:“Cable Strap”.
To attach the cable to a brick or concrete wall:
1. Drill a 3/16-in. diameter x 1-1/4 in. deep hole using a masonry drill bit.
2. Insert the anchor flush with the mounting surface.
3. Use cable clamps and screws to attach the cable to the wall.
Bringing the cable indoors
If it is necessary to run a cable through a wall, use a masonry or wood drill bit to drill a
3/4-inch diameter hole.
To bring the cable through an exterior wall:
1. Depending on the material the wall is made of use a wood or masonry drill bit to drill
a 3/4-in. diameter hole.
2. Pass the connector and cable through the wall.
3. Use the putty/sealant (provided with Outdoor Installation kit) to fill the hole.
4. Fashion a drip loop in the cable if the hole is not next to the ground block.
![](/img.php?id=570497&img=bg1f.png)
MOUNTING THE DU AND CU
SpotCell® 2500Xe 23
Grounding the DU
When the DU is installed outside, electrical (or building) code calls for the outer
conductor of the coaxial cable to be grounded at or near the point of entrance of the
cable into the building. A ground-block is provided with the option outdoor installation
kit.
Figure 3.2: Ground coaxial cable with ground block
Drip Loops
While securing the cable outside, ensure that a drip loop is fashioned on both sides of
the ground block and fasten a tie wrap around the loop to keep the loop secured.
Figure 3.3: Drip loops on both sides of ground block
If where the cable enters the building is not next to the ground block, then another drip
loop will also have to fashioned at this point. The drip loop prevents water from collecting
around the cable where it attaches to the block or where it enters the building.
CU
DU
Ground block
to DU
wall
penetration
to CU
![](/img.php?id=570497&img=bg20.png)
MOUNTING THE DU AND CU
24 SpotCell® 2500Xe
Ideally the ground block should be bonded to the roof ground network, a metal cold
water pipe, structural steel, or metal electrical conduit. Use #10-AWG solid-copper wire
(minimum). Green insulation is preferred. Alternatively uninsulated #8-AWG aluminum
may be permitted. Be sure to check national and local code requirements.
Connect the ground wire to the cold water pipe or alternative using an appropriate
crimp-on ring or lug connector. Ground conductor and termination hardware are not
supplied.
Warning! Failure to properly ground the DU will leave the unit and building vulnerable to
damage from lightning strikes. Check local building and electrical code requirements and
comply with both local and national regulations.
Ideally the DU ground wire should be bonded to the roof ground network. For roofs
without such a network use a metal cold water pipe, structural steel, or metal conduit.
3.1.3 DU indoor mounting
To mount the DU indoors:
1. Use the mounting bracket as a template and mark the hole locations.
2. If the mounting is in a solid wood surface, or a stud covered by drywall, drill a 5/32
inch diameter hole. Mount the unit with 2 inch wood screws.
or
If the mounting is in drywall, drill a ¼ diameter hole and insert an anchor. Mount the
unit with 1/2 inch pan head screws.
3. Attach cables to the wall using tie wraps and mount directly to the wall where
possible (using 1/2 inch pan head screws). If an anchor is required drill a 3/16 inch
diameter hole, insert the anchor, and fasten with 1/2 inch pan head screws.
![](/img.php?id=570497&img=bg21.png)
MOUNTING THE DU AND CU
SpotCell® 2500Xe 25
3.2 Mounting the CU
Find a suitable location to mount the unit that will provide good signal coverage. Refer to
section 2.4“Choosing a location for the CU”. The SpotCell 2500Xe CU is surface
mounted using the provided bracket and can be either mounted to a wall or hung from a
ceiling.
To mount the CU
1. Fasten the mounting bracket to the wall or ceiling.
If mounting on a solid wood surface, or stud covered by drywall, drill a 1/8th
inch diameter hole and then fasten the mounting bracket with #6 x 1.5” screws.
Figure 3.4: CU bracket fastened with screws
or
If mounting to drywall, drill a ¼ inch diameter hole, insert the screw anchors, and
then fasten the mounting bracket with 1/2” screws.
or
If mounting to a truss or t-bar, use the clips that are supplied with the optional
SpotCell Suspended Ceiling Mounting kit to hang the CU mounting bracket.
Figure 3.5: CU mount with T-bar clips
![](/img.php?id=570497&img=bg22.png)
MOUNTING THE DU AND CU
26 SpotCell® 2500Xe
2. Position the bottom of the CU into the hole at the bottom of the mounting bracket
and push the top of the CU onto the bracket. You should feel the CU snap securely
into place.
Figure 3.6: Inserting the CU into the bracket
3. Position the CU cover such that the four pins align with the holes on the CU and
push the cover securely into place.
Figure 3.7: Position CU cover over CU
![](/img.php?id=570497&img=bg23.png)
MOUNTING THE DU AND CU
SpotCell® 2500Xe 27
Figure 3.8: CU mounted with cover
4. Secure the cables to the wall using tie wraps and mount directly to the wall where
possible (using 1/2 inch pan head screws). If an anchor is required drill a 3/16 inch
diameter hole, insert the anchor, and fasten with 1/2 inch screws.
3.3 Using the Hidden Cable kit
The Hidden Cable kit includes a BIAS-T (power inserter) and two F-90 connectors that
make it easier to hide the power and RF cables that are normally connected directly to
the CU.
3.3.1 BIAS-T (power inserter)
The BIAS-T (power inserter) is used to discreetly power the system or power the system
from a more conveniently located AC outlet.
To install the BIAS-T
1. Choose an indoor location along the coaxial cable run to install the BIAS-T. The
BIAS-T location must be within 20 feet (6 meters) of an AC outlet so that the power
adapter cord can reach.
![](/img.php?id=570497&img=bg24.png)
MOUNTING THE DU AND CU
28 SpotCell® 2500Xe
2. If the AC adapter can reach the end of the 6 ft (2m) cable (that ships already
attached to the DU) then simply attach the BIAS-T to the DU cable and the cable
coming from the CU.
Figure 3.9: BIAS-T inserted near DU
or
If the DU is too far from the AC outlet, cut the coaxial cable at the chosen location,
properly terminate both ends with Spotwave approved connectors, and attach the
the BIAS to the two new connectors.
Figure 3.10: BIAS-T inserted far from DU
3. Connect the power supply to the BIAS-T and then plug the adapter into an AC
outlet.
![](/img.php?id=570497&img=bg25.png)
MOUNTING THE DU AND CU
SpotCell® 2500Xe 29
3.3.2 F-90 connectors
The 90 degree F connectors included in the kit, allow the coaxial cables to be run
through the CU mounting bracket and directly into the wall opening. Figure 3.11:“F-90
connector used to hide coaxial cable” shows how the cable runs from the hole in the
wall, through the mounting bracket and connects to the F-90 connector on the CU.
Figure 3.11: F-90 connector used to hide coaxial cable
WIth the CU cover in place, the connector and cable are hidden from view.
F-90
connector
to BIAS-T
![](/img.php?id=570497&img=bg26.png)
MOUNTING THE DU AND CU
30 SpotCell® 2500Xe
![](/img.php?id=570497&img=bg27.png)
Spotwave Wireless Inc. 31
4 – Trouble-Shooting
1. Status: The LED on the back of the DU and CU display information regarding the
SpotCell system during operation.
Action: A red LED indicates a fault condition, a yellow LED indicates an overdrive
condition, and blue indicates power on, no faults. A green LED on the CU indicates
reduced coverage due to a signal isolation condition.
2. Status: The LED on the DU is not illuminating.
Action: Ensure the following:
The cable from the DU is connected to the CU port labelled .
The power supply is connected to the CU or BIAS-T (power inserter).
The power supply is plugged into an electrical outlet.
The display has not timed out. Cycle the power off/on to re-activate the display.
If the LED is still not illuminating, contact technical support.
3. Status: My cell phone does not work around the location I would like to install the
SpotCell DU.
Action: Try positioning the DU externally as high as possible.
4. Status: The DU and CU are installed properly, but your cell phone only works in
close proximity to the CU.
Action: There are three factors that may be affecting coverage as described below:
Visually inspect the area around the CU. Ensure that there are not any large
metallic objects directly between the CU and the area where cell phone coverage
is not adequate. Remount the CU so that it is out in the open.
If the signal the DU is receiving is very weak (although still strong enough to allow
operation), the area around the CU within which a cell phone can function will be
relatively small. An effort can be made to improve system performance by raising
or otherwise repositioning the DU in an effort to obtain a stronger signal.
check with your vendor that your SpotCell product is compatible with your cell
phone service.
![](/img.php?id=570497&img=bg28.png)
TROUBLE-SHOOTING
32 SpotCell® 2500Xe
5. Status: The coverage area around the CU suddenly shrinks after a long period of
reliable operation.
Action: This is most likely due to man made environmental influences such as a
large building being erected somewhere in between the DU and the location the DU
is receiving a signal from. Repeating the install procedure with the DU in its current
position may improve system performance (i.e. re-aligning it in the direction that
provides greater signal strength). If this does not help, the DU may have to be
physically repositioned at a different location; going through the install procedure
starting at Choosing a location for the DU on page 11, is necessary at this point.
6. Information: Remote installation SpotCell characteristics.
In order for the SpotCell system to function, there are two basic parameters that
must be met. The DU must receive a minimum amount of wireless signal, and a
physical environment that blocks wireless signals must be in between the DU and
CU (i.e. a wall).
If the DU is not receiving an adequate signal, the system will not work, or, it will work
but provide a very limited area around the CU in which a cell phone will function. In
this instance, it may be possible that only one cell phone will be capable of using the
system at a time. This is typical of applications that are on the fringe, or outside of a
wireless providers advertised coverage area. Improved performance will typically
only be attained by moving the DU to a higher location.
7. Information: Building installations that do not provide for brick, concrete, metal,
or other dense material between the DU and CU.
Action: In this situation it is possible that the signal emitted by the DU will be received
by the CU. This will result in the system lowering the power of the signal it is emitting;
and therefore the area around the CU in which a cell phone will function will become
smaller. To improve performance in this scenario, it is important to:
Maximize the height of the DU
Separate the DU and CU horizontally as much as possible (within the maximum
cable limits as shown in Table 1, Maximum cable length for connecting units on
page 8).
Mount the DU and CU in a back-to-back manner.
![](/img.php?id=570497&img=bg29.png)
Spotwave Wireless Inc. 33
Appendix A – 2500Xe System Specifications
Note: Spotwave Wireless has the right to change specifications without notice.
A.1 CU indicators
The SpotCell 2500Xe CU has two
indicators on the front, a mult-color
LED for status and a 5 bar indicator
for coverage.
CU Status LED
The status of the SpotCell system is indicated by the single multi-color LED located on
the front of the CU. The meaning of each status LED color is listed below.
Color Status
Off No power.
Blue Power on, no faults.
Yellow Overdrive condition (either adjacent or in-band, not discriminated).
Green Reduced coverage due to signal isolation condition.
Red Fault condition (could indicate a system fault, upgrade failure, or
expired activation period).
CU
Status and
Coverage
indicators
![](/img.php?id=570497&img=bg2a.png)
34 SpotCell 2500Xe
CU Coverage bars
The graduated blue bars on the CU indicate the level of coverage which is determined
by the CAS back-off (isolation required to generate optimum output power at the CU).
0 bars indicate either a >20dB back-off or that the power is off.
System will not operate.
1 bar indicates a back-off between 15 and 20dB.
Very small coverage area. Operation may be intermittent.
2 bars indicate a back-off between 10 and 15dB.
Small coverage area that is likely to vary in size.
3 bars indicate a back-off between 5 and 10dB.
Reduced coverage area that may vary in size.
4 bars indicate a back-off between 0 and 5dB.
Good coverage area that will remain stable.
5 bars indicates 0dB back-off.
Optimum and stable coverage area.
![](/img.php?id=570497&img=bg2b.png)
SpotCell 2500Xe 35
A.2 DU signal level indicators:
The SpotCell 2500Xe DU has two indicators on the back, a mult-color LED for status
and a 5 bar indicator for received signal level.
Note: Both indicators automatically shut off after the system has been powered for 20
minutes. To re-activate the display, either cycle the system power off/on or disconnect
and then re-connect the DU’s coaxial cable.
DU Status LED
The status of the SpotCell system is indicated by the single multi-color LED located on
the back of the DU. The meaning of each status LED color is listed below.
Color Status
Off No power or the display has timed-out.
Blue Power on, no faults.
Yellow
Overdrive condition (either adjacent or in-band, not discriminated).
Red Fault condition (could indicate a system fault, upgrade failure, or
expired activation period).
![](/img.php?id=570497&img=bg2c.png)
36 SpotCell 2500Xe
DU Signal Level Indicator
The graduated blue bars on the back of the DU indicate the signal level received by the
DU
A.3 Antenna Specifications:
0 bars indicates either the display has timed-out (normally after 20
minutes) or that the power is off.
1 bar indicates the received signal level from the base station is
very low (
less than -95 dBm
). Operation may be intermittent.
2 bars indicate the received signal is just within operational range
(
between -90 and -95 dBm
).
3 bars indicate the received signal is
between -85 and -90 dBm
.
4 bars indicate the received signal is
between -80 and -85 dBm
.
5 bars indicate the received signal is at the highest level (
greater or
equal to -80 dBm
).
Cell PCS
DU Antenna CU Antenna DU Antenna CU Antenna
Gain (dBi) 9 dBi 0 dBi 12 dBi +1 dBi
Elevation Beamwidth - typical (dg) 60º 90º 45º NA
Azimuth Beamwidth - typical (dg) 45º NA 22º NA
Front-to-Back Ratio (dB) >20 dB 0 dB >20 dB 0 dB
Polarization Vertical
![](/img.php?id=570497&img=bg2d.png)
SpotCell 2500Xe 37
A.4 Architecture (Dual Band 850/1900 Coverage System)
A.4.1 Physical
Frequency Bands PCS Uplink: 1850-1910 MHz Downlink: 1930-1990 MHz
Cell Uplink: 824-849 MHz Downlink: 869-884 MHz
Sub-Bands Operator sub-bands: Operator Specific
Primary sub-band: Cell (A+A'+A'' or B+B') PCS (5, 10, 15 MHz)
Secondary PCS (split-band) options: 5 or 15 MHz
Formats Supported
GSM / GPRS / EDGE / UMTS and
IS-95 / CDMA / 1XRTT / 1XEVDO / TDMA
Typical Coverage Area 25,000 sq. ft (2,300 m2)
Open Coverage Area 50,000 sq. ft (4,600 m2)
System Gain
(fully adaptive, includes antenna)
Uplink: 0 to +85 dB maximum
Downlink: 0 to +85 dB maximum
System Stability Margin > 10 dB (fully adaptive)
Downlink Operating Range -95 to - 45 dBm (receive isotropic power)
Maximum Input Level
(receive isotropic power)
Uplink: -10 dBm
Downlink: -45 dBm
Output Level -EIRP
(fully adaptive)
Uplink: +30 dBm EIRP maximum (fully adaptive)
Downlink: 0 dBm per carrier, maximum +10 dBm composite
Third Order Intercept
(EIRP, radiated)
PCS Uplink: +50 dBm Downlink: +27 dBm
Cell Uplink: +53 dBm Downlink: +27 dBm
Power Consumption < 45 W
DONOR UNIT COVERAGE UNIT
Operating
Temperature
-40
°
to 130 F
°
(-40
°
to +55
°
C)
32
°
to +104
°
F
(0
°
to +40
°
C)
Size 14 x 12.5 x 3 in.
(36 x 31.5 x 8 cm)
6 x 9.25 x 1.75 in.
(15.5 x 23.5 x 4.75 cm)
Weight 12 lb. (5.5 kg) 2 lb. (1 kg)
RF Connectors Type F: Coverage Port (weatherproof) Type F: Donor Port
Type F: Extension Antenna Port
RF Cable Coverage specification is met with up to 25m RG-6 cable between Donor &
Coverage Units
Optional RF Cable Plenum rated or RG-11 also available
Power Supply Universal power adapter (90 - 260 VAC, 47 -63 Hz)
![](/img.php?id=570497&img=bg2e.png)
38 SpotCell 2500Xe
A.4.2 BW Measurements
A.4.3 Installation
A.4.4 Diagnostics
A.4.5 Coverage Extension
Cell Band A
bandwidth measurement at 20dB down
Uplink = 22.4MHz
Downlink = 23.36MHz
Cell Band B
bandwidth measurement at 20dB down
Uplink = 14.70MHz
Downlink = 14.40MHz
PCS 15MHz bandwidth measurement at 20dB down
Uplink = 16.16MHz
Downlink = 16.24MHz
Installation Time Less than one hour typical
Donor (outward facing)
Unit Alignment
No prior knowledge of base station location required.
Built in alignment algorithm (LED Indicator on Donor Unit).
Test Equipment None required.
No RF knowledge required for installation.
Easy-to-read LED indicators guide installation
User Controls None, setup and operation is fully automatic.
User Interface Built-in LED coverage area display on Coverage Unit
Built-in signal strength display on Donor Unit
Coverage Area Second Coverage Unit provides an additional 25,000 sq. ft (2,300 m2)
coverage when connected to the primary Coverage Unit with up to 164 ft
(50m) of RG-6 cable or 328 ft (100m) of RG-11 cable.
Regulatory Notes and Statements
FCC Declaration of Conformity
This equipment complies with CFR 47, Part 15.19 of the
FCC rules. Operation of the equipment is subject to the
following conditions:
This device may not cause harmful interference; and
This device must accept any interference received,
including interference that may cause undesired
operation.
Information to the User for Class B Digital
Equipment
This equipment has been tested and found to comply with
limits for a Class B digital device, pursuant to part 15 of
the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause interference to radio or
television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna;
Increase the separation between the equipment and
receiver;
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected;
Consult the dealer or an experienced radio/TV
technician for help.
FCC Regulatory Compliance
This equipment has been tested and complies with the
following FCC requirements:
FCC Part 22, subpart H: Cellular Radiotelephone
Services.
FCC Part 24, subpart E: Broadband PCS.
FCC Part 15, subpart C - Intentional radiators.
Industry Canada Compliance
This equipment has been tested and complies with the
following requirements:
RSS - 131 - Zone Enhancers for Land Mobile Service.
ICES-003, Issue 4 - Interference Causing Equipment
Standard - Digital Apparatus
Health and Authorization for Use
SpotCell 2500Xe emits radio frequency electromagnetic
energy to enhance signals received by mobile devices for
in-building coverage. However, the energy level of these
emissions is by far much less than the electromagnetic
energy emitted by other wireless devices.
Caution! To maintain compliance with the FCC's RF
exposure guidelines, this equipment shall be installed and
operated with a minimum distance of 20cm between the
radiator and your body. Unauthorized modification of any
hardware and attachment may violate FCC regulations.
Warning! The use of shielded-type power cord is required
in order to meet FCC emission limits and to prevent
interference to nearby radio or television reception. It is
essential that only the supplied power cord be used. You
are cautioned that changes or modifications not expressly
approved by the party responsible for compliance could
void your authority to operate the equipment.
Maximum Permissible Exposure Statement
The SpotCell 2500Xe is a low power repeater for in-door
coverage. The electromagnetic radiation emitted is much
less than what is specified by FCC. The product has been
evaluated under the FCC Bulletin Office of Engineering
Technology 65c - Evaluating Compliance with FCC
Guidelines for Human Exposure to Radio Frequency
Electromagnetic Fields. This equipment is complaint to the
requirements as set forth in the Code of Federal
Regulation 47, section 2.1091 (Radio frequency radiation
exposure evaluation), section 1.1310 (Radio frequency
Radiation Exposure Limits). Nevertheless, this
equipment shall be installed and operated with a
minimum distance of 20cm between the radiator and
your body. Use of this equipment in a body-worn manner
is strictly prohibited.
Safety Code 6 - Industry Canada Requirement
This equipment has been evaluated for radio frequency
Radiation limits in accordance with the Safety Code 6 -
Limits of Human Exposure to Radio frequency
Electromagnetic Fields in the Frequency Range from 3KHz
to 300GHz. The equipment is complaint to the safety code
6 requirements for the radiation limits as specified in
sections 2.1 and sections 2.2.
Safety Information
The CSA mark indicates that this Equipment meets the
CAN/CSA C22.2 N° 60950-00 and ANSI/UL Std N°
60950-00 - Safety of Information Technology Equipment.
![](/img.php?id=570497&img=bg30.png)
www.spotwave.com
Spotwave Wireless Inc. 1 Hines Road, Ottawa ON K2K 3C7 Canada
© 2005 Spotwave Wireless Inc. All rights reserved. Printed in Canada
Spotwave and SpotCell are trademarks of Spotwave Wireless Inc. Patents pending.