Sun Communications DECT64-S64 US DECT PHONE- HEADSET User Manual users manual
SunCorp Communications Limited US DECT PHONE- HEADSET users manual
users manual
IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment, basic safety precautions should always be followed to reduce risk of fire, electric shock and injury to persons, including the following: 1. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink 2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. 3. Do not use the telephone to report a gas leak in the vicinity of the leak. 4. Use only the power supplies that come with this unit (Type no. MB102-065030 and LF093 00D-41). Use only McNair brand Ni-MH type rechargable batteries of type no. MHAAA550mAh. Do not dispose of batteries in a fire.They may explode. Check with local codes for possible special disposal instructions. 5. Plug the adaptor to the socket-outlet that is near the equipment and shall be easily accessible. 6. CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. SAVE THESE INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS or laundry tub, in a wet basement or near a swimming pool. FCC Interference Information This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference; and (2) This device must accept any interference received, including interference that may cause undesired operation. device, pursuant to Part 15 of the FCC rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna (that is, the antenna for radio or television that is “receiving” the interference. • Reorient or relocate and increase the separation between the telecommunications equipment and receiving antenna. • Connect the telecommunications equipment into an outlet on a circuit different from that to which the receiving antenna is connected. FCC INTERFERENCE INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital FCC RF Radiation Exposure Statement The installation of the base unit should allow at least 20 centimeter between the base and persons in compliance with FCC RF exposure guidelines. For body worn operation, the portable part (handset) has been tested and meets FCC RF exposure guidelines. This device must not be co-located or operating in conjunction with any other antenna or transmitter.The changes or modifications not expressly approved by the party responsible for compliance could void user’s authority to operate the equipment. 1.1 Handset description 1.1.1 Handset keypad Some keys have more than one usage depending on the MMI state (standby, in call, menu mode). The table hereafter gives all the possible actions for each key. In the following chapters, the reference for one key will be indicated with the main action of the key. Sometimes the second (or third) meaning will be indicated as follows: KEY_USE1/KEY_USE2. Key name Standby mode KEY_MENU/OK Enter menu Incoming call Talk mode from incoming Outgoing call call Menu mode Phoneboo k mode confirm confirm MENU KEY_LNR Redial/Pause Enter Redial list Pause Redial (first key in call) Pause (after first key) Pause KEY_UP/CLIP ▲ Enter CLIP list Ringer volume up Receiver Volume Up Receiver Volume Up choose choose KEY_DOWN/CLIP ▼ Enter CLIP list Ringer volume down Receiver Volume Down Receiver Volume Down choose choose KEY_MEM/EXIT Enter Phonebook Enter Phonebook Enter Phonebook Exit Exit Toggle Mute Toggle Mute Clear Clear Standby mode Standby mode KEY_CLEAR KEY_HOOK Go in TALK mode Go in TALK mode KEY_INT Intercom Transfer the call Transfer the call Power off (hold) Flash Flash Pre-dial 0 Dial 0 Dial 0 Pre-dial 1 (DDK1:Long) Dial 1 Dial 1 Pre-dial 2 (DDK2:Long) Dial 2 Dial 2 Pre-dial 3 Dial 3 Dial 3 Pre-dial 4 Dial 4 Dial 4 Pre-dial 5 Dial 5 Dial 5 Int KEY_R/POWER KEY_0 KEY_1 KEY_2 KEY_3 KEY_4 KEY_5 1 of 25 KEY_6 Pre-dial 6 Dial 6 Dial 6 Pre-dial 7 Dial 7 Dial 7 Pre-dial 8 Dial 8 Dial 8 Pre-dial 9 Dial 9 Dial 9 Pre-dial * Toggle key lock (Hold) Pre-dial # Dial * Go into DTMF mode from pulse Dial # Go into Conference call Dial * Go into DTMF mode from pulse Dial # Go into Conference call KEY_7 KEY_8 KEY_9 KEY_STAR/LOCK KEY_HASH Short press is less than 1 second Long press is more than 1.5 second Hold is press and hold more than 3 seconds 2 of 25 1.1.2 LCD display The LCD display is composed of 12 characters in capital letter form (12 * 14 segments alphanumeric chars) and 16 icons. The definition of the icons is as follows: Icon NAME Definition HOOK_IND Off hook indicator EXT EXT External call engaged INT INT Internal call engaged NEW_CLIP_IND Caller identification available /new numbers in call listing CLIP_ANSWERED indicate answered call CLIP_UNANSWER indicate unanswered call ED PHONEBOOK_IND Phonebook indicator MENU_IND Menu indicator BATTERY 3 levels battery indicator 1 segment: weak, 2 segments: medium, 3 segments: full The segments scroll during battery recharging and stop scrolling when battery is full Handset keypad locked LOCK_IND LEFT_ARROW Signal strength indicator. The icon is steady when handset is locked to its base The icon flashes when the handset is unlocked or not subscribed to any base Indicates that displayed number is longer than the screen (12 digits) RIGHT_ARROW Indicates that displayed number is longer than the screen (12 digits) Alarm set Indicates when set the alarm ON ANTENNA (Alarm set icon will be defined later) 1.1.3 Standby display In standby mode, the display shows the current time and the handset number (space and 1 digit), preceded by HS (After Talk OFF, the display shows the handset name and the communication duration alternately for 5 seconds) EX 1(_15 – 53__ HS_ 2) EX 2(DECT9 HANDSET) (The “-“ between hour and minute shall be flashing every second) 1.1.4 LED • Talk LED Action LED state 3 of 25 Standby mode Subscription mode In call Incoming call OFF Flash Flash Flash synchronized with PSTN ring pattern. • Key backlight LED Action Standby mode During incoming call External call External call on hold LED state OFF Flash (0.25 s ON/OFF) ON Flash (0.5 s ON/OFF) • LCD backlight LED Action Standby mode (No key press) Press any key During key lock Incoming call 1.2 LED state OFF ON for 8 seconds after press last key OFF ON Base description 1.2.1 Page Key Key action Short press (<5 s) Long Press (>=5s) MMI action Send a page to handsets Enters subscription mode (in use LED will flash) 1.2.2 LED Power/In use LED Action Standby mode Subscription mode In call Incoming call LED state ON Flash Flash Flash synchronized with PSTN ring pattern. 1.2.3 Tones The three base melodies are shown in the following table Nr Name Ring 1 Ring 2 Ring 3 Ring 4 Ring 5 TONE_CONFIRM Main User interface 4 of 25 2.1 Power up Plug the power supply into the base. The in use LED will power on and TONE_CONFIRM. Insert batteries in the handset. If battery level is enough (see Start up with low batteries chapter), the handset will start. The display will show “BASE 1” and antenna flashing, until it locks onto its subscribed base. If the handset finds its base in the first 10 seconds, no beeps are played (see Range indication chapter). Then the display shows the standby display. 2.2 Standby mode In standby mode, the display shows the current time and the handset number, preceded by HS. The ANTENNA icon is steady. The BATTERY icon indicates the charge level. Handset: Events Press KEY_HOOK Press KEY_INT Press KEY_MENU Press KEY_MEM Press KEY_STAR/LOCK (hold 3 second) Press KEY_LNR/PAUSE Press KEY_UP/CLIP or KEY_DOWN/CLIP Press KEY_R/POWER (hold 3 second) Press 1,2,3……0,*,# Incoming call signal Another handset TALK Battery is low Battery is too low On charging Long press for 1 or 2 Handset mode Enter TALK mode Enter intercom mode Enter MENU mode Enter phonebook mode Enter KEY LOCK mode Enter redial list mode Enter CLIP mode Enter power down mode Pre-dialling Incoming call mode Busy mode Battery low icon Power down mode Charging mode Access direct pre-programmed number Base: Events Press PAGE KEY Incoming call signal 2.3 Base mode Enter PAGE mode Incoming call mode TALK mode Refer to External outgoing call 2.4 Intercom mode Refer to intercom 2.5 Incoming call mode Refer to incoming call 5 of 25 2.6 MENU mode Refer to MENU settings 2.7 Phonebook mode Refer to phonebook 2.8 Redial list mode Refer to redial features 2.9 CLIP mode Refer to Caller ID (CLIP) feature 2.10 Charging mode Refer to Charging conditions 2.11 Busy mode When one Handset is TALK, another handset’s “EXT” icon, and TONE_BUSY in earpiece if press KEY_HOOK 2.12 Power down Make a long press on KEY_R/POWER, and the handset power down. Press and hold KEY_R/POWER for 5 seconds to wake it up. When the handset wakes up, the clock time data shall be transferred from base. 3.1 Call User interface Incoming call Display The display shows "CALL" and EXT icon blinks (0.5 s ON/OFF), if caller ID information is available (see 3.5), caller name or number is displayed. Both the Talk indication LED and key backlight shall be flashed during ringing. (0.25 s ON/OFF) And LCD backlight shall be turned on. Handset and base ringer melody and level as MENU setting. Note 2: It is possible to change ring volume during the incoming alert by using KEY_UP/CLIP and KEY_DOWN/CLIP keys. The ring volume will be displayed as “VOLUME n” (1<=n<=5) or “VOL OFF” during 8 s unless KEY_HOOK is pressed. Incoming alert phase: The incoming call phase begins with the first ring (ALERT_ON) signal of the handset and stops: • If the user take the call (see operation) • If the call is not answered and the caller release its call or another parallel phone answers. EXT icon and LEDs will stop flashing after FTXX_LINE_EXPIRY. The Base ring alert is synchronized with the PSTN ring ON/OFF pattern. 3.1.1 To answer the call: Press KEY_HOOK. Simply lift the handset from the cradle. HOOK_IND icon will be displayed. 6 of 25 Note 1: After it goes to talk mode automatically, KEY_HOOK will be disabled about 3 seconds to prevent unwanted hang up. Note 2: Once handset TALK on, another handset’s display “EXT” icon and can not TALK & TONE_BUSY in earpiece if press KEY_HOOK 3.2 External outgoing call Normal dialling : • • Press KEY_HOOK Enter the called number Pre-dialling: Pre-dialling allows you to enter and modify a number before dialling. • Dial your called number. Up to 32 digits (included pause, *,#)are allowed. If the number exceeds 12 digits, the last 12 digits are displayed and LEFT_ARROW is ON, Press KEY_CLEAR key to delete last digit. • Press KEY_HOOK, the digits are dialled, digit(s) 3.2.1 Dialling PAUSE Press KEY_LNR (after first key) to make a pause, which is displayed as a "P". The time is adjustable by FP EEPROM settings 3.2.2 Flash key During a call, press shortly KEY_R to perform a Flash break and displayed as a “R”. The flash time is adjustable by FP EEPROM settings 3.2.3 DTMF dialling DTMF tone duration (pause before, tone length, pause after, high & low group level) is adjustable by FP EEPROM settings 3.2.4 Pulse dialling Pulse timing (make, break, pause after) is adjustable by FP EEPROM settings Pulse dialling mode can be disabled by EEPROM settings. (If disabled by setting, the dialling setting menu shall not be on the handset setting menu) 3.2.5 Temporary DTMF dialling During a call or pre-dialling, when the selected dial mode is pulse and you want to dial DTMF codes, During talk, long press KEY_STAR/LOCK to switch into DTMF dialling, only during this call. During pre-dialling or number storage, long press KEY_STAR/LOCK is used to program the digits after the KEY_STAR going temporarily to DTMF dialling. This will be displayed as a “d”. 3.2.6 Dial tone detection During an external outgoing call, the dial tone detection is activated. When detected the digits which have been dialled on the handset (pre-dialled or post dialled) are sent to the line. If the dial tone is not detected, a time out expires and the digits are sent. The time out is adjustable by FP EEPROM settings No dial tone detection time out : selected by EEPROM data with dial tone detection time out : selected by EEPROM data 3.2.7 Call timer display After going off hook, the display is blank during 15 s unless you press a key. The communication duration is displayed after 15s after the last pressed key 7 of 25 If you press a key (0 - 9) during the conversation, the communication duration is not reset to zero and reappears after 15 seconds. At the end of each call, the duration of communication and the handset name are displayed alternately for 5 seconds. 3.2.8 Mute It is possible to mute the microphone during a conversation. Press KEY_CLEAR/KEY_MUTE during the conversation, the microphone is then deactivated, the external correspondent is put on hold; you can talk freely without being heard by the calling party. “MUTE” is displayed. No digit key or KEY_INT can be used during mute. And Phonebook can be reviewed but can’t be dialled out during mute. Press KEY_CLEAR/KEY_MUTE again to return to normal mode. 3.2.9 Changing Earpiece Volume during Call It is possible to change earpiece volume during a call using KEY_UP/CLIP and KEY_DOWN/CLIP. The earpiece volume will be displayed as “EARVOL n” (1<=n<=5) during 8 s unless a key digit (KEY_0 to 9 + KEY_HASH + KEY_STAR) is pressed. 3.3 Direct access memory The product has two locations of direct access memory dial number. The number is pre-programmed to the EEPROM and user cannot change it. The maximum digits for each location are 16 digits and there is no name for this direct access dial number. 3.3.1 How to access the direct memory dial number during idle User press and hold the KEY_1 or KEY_2 for more than 1.5 second (Long press), then the unit display pre-programmed number on the LCD and dial it out. KEY_1 for location number 1 and KEY_2 for location number 2. 3.3.2 During OFF HOOK When the unit is on OFF HOOK mode, it is only allowed to access direct access memory number when the first key in is long press for KEY_1 or KEY_2. 3.4 Redial feature 3.4.1 Redial list Up to 10 last redial numbers (32 digits) are stored in the redial list (in PP EEPROM). The last calls appear with their name if they are stored in the phonebook. To retrieve the entries: Press KEY_LNR If the list is already empty, then “empty” is displayed • Scroll through the calls with the up KEY_UP/CLIP and down KEY_DOWN/CLIP arrows. The phonebook name is displayed if it exists. Otherwise it displays the first 12 digits of the number. • Press KEY_OK to toggle between name and number, • Press KEY_MEM/EXIT return to standby mode To dial out number just simple press KEY_HOOK. 3.4.2 Dial out redial after OFF HOOK To recall the last redial entry, just take the line by KEY_HOOK and press KEY_LNR to dial. 8 of 25 3.4.3 Delete a redial buffer : • • Press KEY_CLEAR and “DELETE ?” appears. Press KEY_OK to make redial number deleted, or press KEY_MEM/EXIT to cancel the delete operation. To return to the previous menu, press KEY_MEM/EXIT 3.4.4 Delete all redial buffer : • • Long press KEY_CLEAR and “DELETE ALL?” appears. You can either press KEY_OK again and all redial are deleted, or press KEY_MEM/EXIT to cancel the delete all operation. To return to the previous menu, press KEY_MEM/EXIT 3.4.5 Store a Redial list into PHONEBOOK • • • • • • • 3.5 Press KEY_OK during display the redial number which you wish to store to the phonebook. The display show “ADD ?”. After appearing the “ADD ?” And press KEY_OK to confirm. The display show “NAME ?”. Enter the name. Press KEY_OK after modified name. Press KEY_OK after modified number. Select the melody of your choice (1 to 5) and validate Press KEY_OK to confirm. Internal call transfer When you wish to transfer an external call to another extension: • • During a call, press KEY_INT Select the number of the internal correspondent that you wish to call; the external caller is put on hold. • When the internal correspondent picks up, press KEY_HOOK to hang up and transfer the call. If the internal correspondent does not pick-up, press KEY_INT again to reconnect to the external caller on line. 3.6 Conference call between two handset and external caller When you wish to talk an external call and other handset: • During a call, press KEY_INT • Select the number of the internal correspondent that you wish to call; the external caller is put on hold. • When the internal correspondent picks up, you can talk with internal correspondent first with external call on hold. • Press KEY_# to go to Conference call. • When one of handset press KEY_HOOK or press KEY_INT. Then the conference call is finished, but other handset still talk with external caller. If the internal correspondent does not pick-up, press KEY_INT again to reconnect to the external caller on line. 9 of 25 3.7 Caller ID (CLIP) features 3.7.1 General features The phone supports CLIP DTMF and FSK type I and II. See 8.1 for more details. 3.7.2 Caller ID display Note: Caller identification is only available if you have subscribed to this service with your network operator. During the incoming alert: The CLIP information is displayed if they are provided. Order of display: • Phonebook name and calling number alternately if the number matches with the CLIP calling number • CLIP calling name and calling number alternately if the network is transmitted. However, if the number is match with one of phonebook memorized number, it shall use phonebook memorized name. • CLIP calling number • Number matching method is as follows. - If the one of number which CLIP or phonebook is less than 5 digits, it will not compare. (If the one of phonebook number is 1234, this number will not use for number matching) - If the CLID received 10 digits and phonebook number is 8 digits, CLID last 8 digits will use for the matching with that phonebook number. And if the CLID is 8 digits and phonebook number is 10 digits, Phonebook number last 8 digits will use for the matching with that CLID number. The following special network messages are managed and displayed at the place of calling number: Message WITHHELD UNAVAILABLE CLIP type FSK type I & II FSK type I & II Meanings The caller hides its identity Network failure, the calling number can’t be transmitted Special caller texts display format: Display WITHHELD UNAVAILABLE INT NATIONAL OPERATOR PAYPHONE RINGBACK The CLIP TYPE FSK type I & II FSK type I & II FSK type I & II FSK type I & II FSK type I & II FSK type I & II Caller texts from network PRIVATE UNAVAILABLE INTERNATIONAL OPERATOR PAYPHONE RINGBACK icon will stay during all incoming alert phase or if you answer the call. The call timer display will come again after 15 seconds if no key pressed. During standby mode: The icon will flash if unanswered CLIP(s) in call list, call is read. 3.7.3 icon will be off after all unanswered Recall CLIP list 10 of 25 Unanswered and answered calls are stored in the CLIP list of each handset independently (in EEPROM). Note: any new CLIP call will be stored in EEPROM . Size storage Each entry will store: ¾ ¾ ¾ The call number (20 digits) The caller name (12 digits) if the network send it The date and hour of the call Storage sequence The CLIP information that has been received during incoming alert phase (calling number, name date/hour) is stored then displayed. If the new call entries, The icon will flash (480ms ON/OFF) and will off after all new call is read. Note: The new message indication is reset at power up, so the icon is always off after a reset. MMI operation To retrieve the entries: 1. Press KEY_ UP/CLIP or KEY_ DOWN/CLIP to enter the call list. The 2. 3. for Unanswered Calls and the icon will stay ON for Answered Calls. If the list is already empty, then “EMPTY” is displayed Scroll through the calls using the up KEY_UP/CLIP and down KEY_DOWN/CLIP arrows. You will find the different fields of the entry: If the call is unanswered and unviewed. The and icon will stay ON icon will stay ON. The will be turned off after it is viewed. If a matched number found in phonebook memory , the corresponding name will be shown otherwise if the caller name is available, the caller name will be displayed. If both are not available, the caller number is displayed first. Press KEY_OK, the first 12 digits of caller number is displayed , press KEY_OK again to check the remaining digits ( if more than 12 digits ) 4. Press KEY_OK The date and hour is displayed if any 5. When the CLIP found no matched number in Phone Book and Calling Number is present, when press KEY_OK again , CLIP data can be stored into phone book ( see 3.5.6 ) To select another call list, simply press KEY_UP/CLIP or KEY_DOWN/CLIP . Error tone will be sounded if reach the top or bottom of the list. To return to the previous menu, press KEY_MEM/EXIT. To dial out number just simple press KEY_HOOK 3.7.4 Delete one CLIP list • • 3.7.5 Press KEY_CLEAR and “DELETE ?” appears. There you can either press KEY_OK and CLIP deleted, or presses KEY_MEM/EXIT to cancel the delete operation. Delete all CLIP list • • Long press KEY_CLEAR and “DELETE ALL?” appears. There you can either press KEY_OK and all CLID are deleted, or press KEY_MEM/EXIT to cancel the delete all operation. To return to the previous menu, press KEY_MEM/EXIT 11 of 25 3.7.6 Store a CLIP list into PHONEBOOK • • After appearing the “ADD ?” and press KEY_OK to confirm ( after 3.6.3 step 5 ) Press KEY_UP/CLIP or KEY_DOWN/CLIP to move the cursor for edit or delete name. If the CLIP data does not have name, LCD shall display “NAME ?”. And then enter the name. Press KEY_OK after modified or enter the name. Press KEY_OK after modified number. Select the melody of your choice (1 to 5) and validate Press KEY_OK to confirm. • • • • 3.7.7 Dial out CLIP list To recall the number from CLIP list , pressing KEY_HOOK will dial out the number . 3.8 Phonebook The phonebook contains up to 50 names of 12 characters max. and numbers of 20 digits. Phonebook is stored in PP EEPROM. One handset phonebook is independent from other locked handsets. 3.8.1 Dial a number of the phonebook list To call a correspondent whose name you have saved in the phonebook: • • • • • • 3.8.2 will be ON. Press KEY_MEM/EXIT to enter the phonebook. The Press the first letter of the name; the first name that starts with this letter in the alphabet appears. For instance to find names beginning by A, press once on KEY_2, to find names beginning by B, press twice on KEY_2, to find names beginning by C, press three times on KEY_2 Go through the list of names with the KEY_UP/CLIP and KEY_DOWN/CLIP keys the list scrolls up/down in an alphabetical order. Press KEY_MENU/OK to display the number and user can press the KEY_MENU/OK again to display remaining digits if the recalled phone book number is more than 12. Press KEY_MEM/EXIT returns to standby mode OR Press KEY_HOOK to dial the number of the correspondent whose name is displayed. Dial a number of the phonebook list during Talk. • • • • • • Press KEY_MEM/EXIT to enter the phonebook. The will be ON. Press the first letter of the name; the first name that starts with this letter in the alphabet appears. For instance to find names beginning by A, press once on KEY_2, to find names beginning by B, press twice on KEY_2, to find names beginning by C, press three times on KEY_2 Go through the list of names with the KEY_UP/CLIP and KEY_DOWN/CLIP keys the list scrolls up/down in an alphabetical order. Press KEY_MENU/OK to display the number and user can press the KEY_MENU/OK again to start dialling or display remaining digits if the recalled phone book number is more than 12. Press KEY_MENU/OK again to start dialling and return to normal Talk mode. Press KEY_MEM/EXIT without dialling, then returns to normal Talk mode 12 of 25 3.9 Intercom 3.9.1 • • Internal call Press KEY_INT Enter the number of the internal handset (1 to 5) and “INT” icons displayed, the number of the internal handset display “INT” with caller The handset number and rings (INT MEL). Remark: the caller handset go to standby mode if the number of the internal handset is not available or caller handset 3.9.2 End of intercom call Incoming call applied then go to ring in mode. The number of the internal handset press KEY_HOOK go to INTERCOM mode 3.9.3 Intercom mode The 3.9.4 and “INT” icons displayed on both handsets. End of intercom Any handset (intercom) press KEY_HOOK, go to standby mode Incoming call applied then go to ring in mode. 3.10 Page button Press Page button on the base. The handsets will ring RING_1 at volume of Handset internal ring level setting and display INT with “□□□□”during 30s unless page key is pressed again on the base or a key is pressed on any locked handset. (When the handset set to key lock, user can be stop the paging by pressing any key) 3.11 Battery and charge management 3.11.1 Battery indicator 5 levels indicators icon for mean battery voltage: > = EEP_BAT_FULL_LEVEL > = EEP_BAT_HALF3_LEVEL > = EEP_BAT_HALF2_LEVEL, Blinking > = EEP_BAT_ALARM_LEVEL 3.11.2 Low battery conditions If the following conditions are applied: During a call, • If mean battery level is less than EEP_BAT_HALF1_LEVEL, 13 of 25 • If battery warning tone option is ON then a TONE_LOW_BATT will be emitted every minute. In any state (standby or call), If mean battery level is less than EEP_BAT_ALARM_LEVEL, handset will enter in power down mode. 3.11.3 Charge conditions If the following conditions are applied: • In standby mode, • If battery warning tone option is ON • The handset is put on its charger (debounce time: 200 ms) then a TONE_CONFIRM will be played. Charging icon: Scroll for display handset is charging, fast scroll when quick charging mode, 3.11.4 Quick charge If the battery voltage below EEP_BAT_HALF2_LEVEL, the charging mode is always quick charge mode first until the following condition detect. • If detect negative ∆V then stop quick charge • If reach to time limit which defined by EEPROM setting 3.11.5 Start-up with low batteries If battery level at start-up is lower than EEP_BAT_HALF2_LEVEL, the handset will stay in sleep mode (no LCD, no RF, no MMI working). You need to put the handset into charge until battery level reaches EEP_HALF2_LEVEL. 3.12 Range indication 3.12.1 Out of range tone If the following conditions are applied: • The handset has been out of range since EEP_RANGE_OUT_DELAY s • If range warning tone option is ON then a TONE_WARNING will be played. EEP_RANGE_OUT_DELAY : selected by EEPROM data 3.12.2 In range tone If a TONE_WARNING has been played, a TONE_IN_RANGE is played when the handset goes into range the next time. Note: at start-up, the handset plays the TONE_IN_RANGE only if it goes into range after more than 10 s. 3.12.3 Range limit tone during a call During a call, in range limit conditions, the handset will play a TONE_WARNING in the Buzzer The tone is repeated until range conditions are good If the handset goes out of range, the call is released (on both handset and base). 14 of 25 3.13 Alarm activation When the unit is set to alarm ON and the clock reach to the alarm setting time, the handset shall generate the alarm sound and display “ALARM ON” on LCD. Once the clock is reach to alarm setting time, the alarm setting shall be OFF. 3.13.1 During idle The sound level shall follow the handset internal ring level. However, if the setting is “OFF” the alarm sound level shall be “LEVEL 1”. During generating the alarm sound, press any key to stop the alarm without any operation even the handset is “Key Lock” mode. For example, press “KEY_HOOK” to stop the alarm, however, the handset should not go to talk mode. If do not press any key for more than one minute, the alarm shall stop automatically. 3.13.2 During Talk The sound level shall be same as Battery Low warning tone. During generating the alarm sound, press any key to stop the alarm without any operation. 3.13.3 During ringing or paging The alarm sound shall not active during paging or ringing. 15 of 25 4 MENU Settings Menu structure A wide range of phone settings are accessible through a user friendly menu. • To enter the menu, press KEY_MENU/OK • Scroll through the selections using the KEY_UP/CLIP and KEY_DOWN/CLIP keys, the selections scroll in a loop (you return to the first after the last). To validate a selection, press KEY_MENU/OK • To return to the previous menu, press KEY_MEM/EXIT. • To escape a menu and return to standby mode, press and hold KEY_MEM/EXIT • After 15 s without pressing any key, the handset returns in standby mode PHONEBOOK ADD ENTRY NAME ? NUMBER ? MELODY 1 … 5 MODIFY ENTRY MELODY 1 ... 5 DELETE ENTRY CONFIRM ? SETUP BASE VOLUME VOLUME OFF VOLUME 1 ... 5 BASE MELODY MELODY 1 … 5 DEL HANDSET PIN ? HANDSET ? PIN CODE PIN ? NEW PIN RETYPE DIAL MODE TONE (dtmf) DIAL PULSE DIAL RECALL RECALL1 RECALL2 HANDSET DEFAULT PIN ? CONFIRM ? BEEP KEYTONE ON OFF LOW BATTERY ON OFF OUT RANGE ON OFF INT RING VOL VOLUME OFF VOLUME 1 … 5 EXT RING VOL VOLUME OFF VOLUME 1 … 5 INT MELODY MELODY 1 … 5 EXT MELODY MELODY 1 … 5 CLOCK SET ALARM SET ON OFF 16 of 25 AUTO ANSWER OFF ON NAME LANGUAGE ENGLISH NEDERLANDS FRANCAIS DEUTSCH ITALIANO ESPANOL ΕΛΛΗΝΙΚΑ РУССКИЙ DANSK SVENSKA NORGE POLSKI ČESKY SLOVENCINA PORTUGUES MAGYAR KEY LOCK ? REGISTER SELECT BASE *+BASE 1 2 3 4 NEW BASE X AUTO REG BASE +BASE 1 2 3 4 SEARCHING X PIN ? Notes : * Only registered base number will be shown. Notes : + Registered Base Number will blinking 4.1 PHONEBOOK • 4.1.1 • Select "PHONEBOOK" Add a name Select "ADD ENTRY" 17 of 25 • • • • • Enter the new name and validate. Enter the new telephone number and validate It is possible to enter the following data for number entering. - KET_1 to KEY_0 - KEY_STAR and KEY_# - KEY_LNR (Pause) - KEY_R (Recall, Flash) Select the melody of your choice (1 to 5) and validate Press KEY_OK to confirm. With your telephone you can write text as well as figures. This is useful for entering a name into the address book, giving a name to a handset, … To select a letter, press the corresponding key as many times as is necessary. For example to select an 1, press 2 once, to select a B, press 2 twice and so on. To select A and then B consecutively, select a 1, wait until the cursor moves on to the next character, then select a B. To select an empty space, press 1. To select a dash, press 1 twice The keypad characters are as follows: First press Second press Space Third press 4.1.2 • • • • 4.1.3 Fifth press Delete a name Select "DELETE ENTRY" Move through the list of names using the KEY_UP/CLIP and KEY_DOWN/CLIP keys the list scrolls down in alphabetical order. Press KEY_OK when you find the name you wish to delete "CONFIRM ?" appears, press KEY_OK to confirm. Modify a name or number • • • • • • • • • 4.2 Fourth press Select "MODIFY ENTRY" Move through the list of names with the KEY_UP/CLIP and KEY_DOWN/CLIP keys. The list scrolls down in alphabetical order. Press KEY_OK when you find the name to modify Press KEY_UP/CLIP or KEY_DOWN/CLIP to move the cursor for edit or delete name. Press KEY_OK after modified name. Press KEY_CLEAR to delete number. Press KEY_OK after modified number. Select the melody of your choice (1 to 5) and validate Press KEY_OK to confirm. SETUP • • Select "SETUP" In idle, all the handsets which registered to the same base can enter the “SETUP” menu in the same time, and the last setting will be validated. 18 of 25 4.2.1 BASE VOL This menu enables you to adjust base ring volume • Select "BASE VOLUME" and validate • Select the desired volume (VOLUME OFF or VOLUME 1 to 5) and validate 4.2.2 BASE MEL This menu enables you to select base ring melody • Select "BASE MELODY" and validate • Select the melody of your choice (1 to 5) and validate 4.2.3 DEL HS You can cancel a handset’s association with a base to allow another handset to be associated • Select "DEL HANDSET" and validate • Enter the PIN code and validate • Select the handset to be cancelled and validate 4.2.4 PIN CODE The base PIN code is used in subscription operation or to modify some critical parameters in the base. To change the PIN code: • Select "PIN CODE" and validate • Enter the old 4 figure confidential code and validate • Enter the new 4 figure confidential code and validate • Enter the new confidential code a second time and validate 4.2.5 Dial mode selection (This mode will not appear when set the Pulse dialling disable by EEPROM Two types of dialling are available: 1. 2. DTMF tone dialling Pulse dialling To change the dialling mode: • Select “DIALMODE” and validate • Select “TONE” or “PULSE” of dial mode and validate FTXX_DIAL_MODI : selected by EEPROM data Note: the Dial mode selection menu can be hidden to lock the base into pulse or DTMF dialling by the CONFIG_ENA_MENU_DIALMODE flag (see various factory settings). 4.2.6 Recall duration selection • Select "RECALL" • Choose RECALL 1 to select short flash time • Choose RECALL 2 to select long flash time RECALL 1 & 2 timing : selected by EEPROM data Note: not recall select function in if RECALL 1 & RECALL 2 is same timing. 4.2.7 Default settings This menu enables you to reset both handset and base with default settings. By SET UP menu, • Select "DEFAULT" • Enter the base PIN code and validate • "CONFIRM ?" appears, press KEY_OK to confirm By quick default, 19 of 25 • Press and hold * key when insert the battery for 5 seconds, “DEFAULT” appears, then “CONFIRM?”, press KEY_OK to confirm Then the handset and base will apply default parameter settings and make a software RESET. Default parameter Handset name Low battery indicator Out of range indicator Key click Auto answer INT melody INT volume EXT melody EXT volume ear volume Language Phonebook CLID list Redial list PIN CODE PAUSE dial mode Key lock CLOCK ALARM Value TBD ON ON ON ON English Empty Empty Empty 0000 3s DTMF(Tone) OFF 00 :00 OFF Default values in handset and base are defined by EEPROM settings [1]. So they can be adjusted for each country. 4.3 HANDSET • Select "HANDSET" 4.3.1 BEEP Beep features The handsets may or may not emit beeps while the keys are pressed , the batteries are low and when the handset is out of range of the base. 4.3.1.1 • • 4.3.1.2 • • 4.3.1.3 • • KEYTONE Select "KEYTONE" and validate Select “ON” or “OFF” and validate LOW BATTERY Select "LOW BATTERY" and validate Select “ON” or “OFF” and validate OUTRANGE Select "OUT RANGE" and validate Select “ON” or “OFF” and validate 4.3.2 INT RING VOL This menu enables you to adjust handset ring volume (intern melody) 20 of 25 • • Select "INT RING VOL" and validate Select the desired volume (VOLUME OFF or VOLUME 1 to 5) and validate 4.3.3 EXT RING VOL This menu enables you to adjust handset ring volume (extern melody) • Select "EXT RING VOL" and validate • Select the desired volume (VOLUME OFF or VOLUME 1 to 5) and validate 4.3.4 INT MELODY This menu enables you to choose a different melody for internal call • Select "INT MELODY" and validate • Select the melody of your choice (1 to 5) and validate 4.3.5 EXT MELODY This menu enables you to choose a different melody for external call • Select "EXT MELODY" and validate • Select the melody of your choice (1 to 5) and validate 4.3.6 CLOCK SET Clock setting is 24-hour format. • When enter Clock setting mode, LCD display current time with flashing hour indication. • Enter the current time by 24-hour format and validate. And same time, the update data send to base to keep for all the handset to have same clock. • If the CLIP data has time data, the clock shall be updated by CLIP time data. • The time data shall be kept at base unit and when the handset turned on, the time data shall be transferred from base to handset. 4.3.7 ALARM SET This menu makes the handset to have alarm clock feature. • Select ON or OFF and validate • If select ON, then the menu go to alarm time setting mode • Time setting is same as Clock setting 4.3.8 AUTO ANSWER When there is an incoming call and the handset is on the base, the phone automatically takes the line. • Select "AUTO ANSWER” and validate • Select "ON" to activate "OFF" to deactivate and validate 4.3.9 NAME This function allows you to personalise each handset. • Select "NAME" and validate • Enter the name and validate (max 10 chars) 4.3.10 KEY LOCK This function allows you to lock the key • Select "KEY LOCK?” and validate • Press KEY_MENU/OK to lock key, icon displayed and go to standby mode. Note :Press KEY_HOOK key can be OFF HOOK during incoming call and KEY LOCK is on. 21 of 25 4.3.10.1 Quick KEY LOCK Simply press and hold KEY_STAR/LOCK 3 second 4.3.10.2 To unlock key: • • 4.4 Press any key “PRESS *” is displayed, within 5s time out Press KEY_STAR/LOCK to unlock key REGISTER • • • 4.4.1 • • • • • 4.4.2 • • • • • • • Select "REGISTER" and validate Select “SELECT BASE” or “REG BASE” by KEY_UP or KEY_DOWN Press KEY_OK to confirm SELECT BASE Select "SELECT BASE" and validate “BASE 1 2 3 4” is displayed ( only the registered base number will be shown and current base number will be blinking) Press 1 - 4 to confirm the selection or KEY_UP/KEY_DOWN + KEY_F to select auto searching. Valid tone is sounded if valid base is found “NOT REGISTER” is shown and error tone sounded the selection is invalid REG BASE Select "REG BASE" and validate “BASE 1 2 3 4” is displayed ( only the registered base number will be blinking ) Press 1 - 4 to confirm the selection It is now searching the base in subscription mode and “SEARCHING…” is displayed Valid tone is sounded and “PIN ?” is shown if valid base found Enter subscription PIN code and verified by base Valid tone sounded if subscription is successful and back to standby mode. On the base: • • Put the base into subscription mode, by pressing and holding PAGE_KEY The base will then emit a beep, the Line LED will flash. It is now ready to be associated with a new handset, during the 90 seconds after pressing the button only. If the handset has located the base, a valid tone is played. If the handset does not locate the base, it will return to the previous configuration after 1 minute. Try again by changing the base number and check that you are not in a environment where there is interference When a handset is associated with a base, it is given a handset number by the base. It is this number which is displayed on the handset after the name and must be used for internal calls. Prefix dialling There are two data for prefix dialing. One is Detect string and other is Replace string. If user enter the number and first sevelrale string match with the pre-programmed string data, then the string will be replaced by pre-programmed Replace string data. This function can be enabled or desabled by EEPROM setting. 22 of 25 5.1 Detect string The pre-programed detect string is 5 digits inside the EEPROM. The data is 1 to 0 and F (F is for blank) If the Detect string need to be 003 then the data shall be F,F,0,0,3 5.2 Replace string The pre-programed replace string is maxmum 10 digits inside the EEPROM. The data is 1 to 0 5.3 Detecting and replacment The prefix dialing is only working when the dialing is prepared dialing which mean enter the dial number during idle mode and then OFF HOOK. The prduct will check the first few digis (maximum 5 digits depended on Detect string data) and if match with detect string, then replace the detected string to the replace string. If the detect string is all F, there will be no matching and add the replace string to the dialed number except the dialed number starting from not 1 to 0. EX 1 Detect string : FFF00 Replace string : 1234567 Dialing number : 00567456 The product will dial ---- 1234567-567456 EX 2 Detect string : FFFFF Replace string : 1234567 Dialing number : 00567456 The product will dial ---- 1234567-00567456 EX 3 Detect string : FFFFF Replace string : 1234567 Dialing number : 13567456 The product will dial ---- 1234567-13567456 EX 4 Detect string : FFFFF Replace string : 1234567 Dialing number : #13567456 The product will dial ---- #13567456 EX 5 Detect string : FFFF0 Replace string : 1234567 Dialing number : 00567456 The product will dial ---- 1234567-0567456 EX 6 Detect string : FFFF0 Replace string : 1234567 Dialing number : 0567456 The product will dial ---- 1234567-567456 EX 7 Detect string : FFF00 Replace string : 1234567 Dialing number : 0567456 The product will dial ---- 0567456 23 of 25 6 Quick default settings If you have lost your PIN code, the following procedure allows you to restore default settings on handset and base. Press KEY_STAR on handset when power up (insert and remove batteries). The display shows “DEFAULT”. Press KEY_OK. When the handset locks onto its base, both will restart. Subscribe a new handset Refer to MENU mode’s REGISTER page The base can support a maximum of 2 handsets. If you already have 2 handsets, and you wish to change one of them, you must firstly delete a handset, then associate the new handset. 8.1 Test modes Handset test modes Refer to document of TEST MODE 8.2 Base unit test modes Refer to document of TEST MODE 24 of 25 9 9.1 Specifications CLIP Standards The phone supports the following CLIP features defined by the identified standard: Feature FSK type I FSK type II Country All applicable Standard ETS 300 659-1 ETS 300 659-2 Note : No impedance matching is required 9.2 DECT Specifications The phone complies with the following standards Part DECT Radio DECT GAP Analog Telephone Network EMC Safety Standard EN301 406 TBR 22 TBR 21 and TBR 38 EN301 489-1 and EN301 489-6 EN 60950 25 of 25
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Encryption : Standard V2.3 (128-bit) User Access : Print Modify Date : 2006:08:21 09:49:32+08:00 Create Date : 2006:07:21 10:24:33+08:00 Creator : Acrobat PDFMaker 6.0 for Word Producer : Acrobat Distiller 6.0 (Windows) Page Count : 30 Has XFA : No About : uuid:4f35ff3a-b58c-4ee8-aa45-b6dd15078d37 Mod Date : 2006:08:21 09:49:32+08:00 Creation Date : 2006:07:21 10:24:33+08:00 Metadata Date : 2006:08:21 09:49:32+08:00 Document ID : uuid:46d135de-d7f3-4074-afe0-59c13d71b694 Format : application/pdfEXIF Metadata provided by EXIF.tools