Ten Tec 588 HF AMATEUR RADIO TRANSCEIVER User Manual

Ten Tec Inc HF AMATEUR RADIO TRANSCEIVER Chapter 1 YOUR NEW OMNI VII

a href="https://usermanual.wiki/Ten-Tec" itemprop="url"> Ten Tec >

USERS MANUAL

Section 1 – YOUR NEW OMNI-VII Our aim in designing and producing OMNI-VII was to meet the demands of increasingly intense competition in DXing and contesting, while adding many non-performance related features that the active ham can also appreciate. OMNI-VII offers superb reception and transmission of CW, SSB, digital modes, FM, and AM on all 10 HF amateur bands and 50 MHz. UNPACKING OMNI-VII Examine OMNI-VII for signs of shipping damage. Should any damage be apparent, notify the delivering carrier immediately, stating the full extent of the damage. Retain all damaged cartons. Liability for shipping damage rests with the carrier. We recommend that you keep the carton and fillers in the event that storage, moving, or shipment becomes necessary. The hardware and accessories listed in Figure 1-1 come standard with your OMNI-VII. Make sure that you have not overlooked anything. ABOUT THIS MANUAL The OMNI-VII is a firmware updateable transceiver. Features and functions on the transceiver can change as time passes when new firmware revisions are issued via Ten-Tec’s www.rfsquared.com firmware download website. The latest version of the OMNI-VII manual is posted in .pdf format on the OMNI-VII section of the Ten-Tec website at www.tentec.com. Schematic diagrams are not included in this manual but are available for download from the www.rfsquared.com firmware website. This manual was written by Scott E. Robbins, W4PA. Qty Part # Description 1 #27074 Mini-ATC Blade Fuse, 25 Amp. 1 #35003 Phono Plug 1 #35363 8-pin Microphone Connector 1 #35165 2-pin Power Connector Shell 2 #41020 Female Power Pins 1 #35017 Phone Plug, 3-circuit 1 #38040 .050 Hex Wrench 1 #38088 .062 Hex Wrench 1 #38313 T10 Torx Wrench 1 #46172 Serial Cable 1 #46176 Accessory Cable. 5-pin DIN to phono female 1 #74020 Warranty Card 1 #74409 User’s Manual 1 #86095 DC Power Cord Figure 1-1 OMNI-VII Packing Kit CONNECTING A POWER SUPPLY The OMNI-VII transceiver requires a source of well-filtered and regulated DC voltage. The supply voltage can range from +12.8 to +15.0 Vdc but +13.8 Vdc is the optimum value. The voltage source must be capable of supplying 22 amperes continuous duty. We recommend using the included DC power cable (P/N 86095). We have also included spare connector pins (P/N 41020) and a spare 2 pin power connector shell (P/N 35165) for building your own cable. The power supply plug will attach in only one direction to the polarized two-pin DC connector on the OMNI-VII rear panel. Use no less than #14 gauge (#12 recommended) stranded wires for three-foot long connections to accommodate the required current demand during transmit. Use heavier gauge wire for longer power supply leads. NOTE: always enable the power source first and then the transceiver. If a generator or alternator supports the dc source, always turn off the transceiver before starting or 588 manual Initial release – October 2006 1 Part #74409 Printed in USA
Download:
Mirror Download [FCC.gov]
Document ID729036
Application IDhZ+112ay+eTPAILADrQYpw==
Document DescriptionUSERS MANUAL
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize17.32kB (216534 bits)
Date Submitted2006-11-16 00:00:00
Date Available2006-11-16 00:00:00
Creation Date2006-11-15 16:02:08
Producing SoftwareAcrobat Distiller 7.0.5 (Windows)
Document Lastmod2006-11-15 16:02:27
Document TitleChapter 1 – YOUR NEW OMNI-VII
Document CreatorAcrobat PDFMaker 7.0.7 for Word
Document Author: Scott
FCC ID Filing: DJ7-588

Navigation menu