Texas Instruments 2510SRF The SmartRFCC2510EM is a development tool for Texas Instruments 2.4 GHz CC2510 System-on-Chip. User Manual

Texas Instruments Inc. The SmartRFCC2510EM is a development tool for Texas Instruments 2.4 GHz CC2510 System-on-Chip. CC2510 Mini Development Kit

a href="https://usermanual.wiki/Texas-Instruments" itemprop="url"> Texas Instruments >

User manual

SWRU235B August 2013 CC2510 Mini Development Kit Quick Start Guide 1 Kit Contents 2 x SmartRFCC2510 target boards 1 x CC Debugger 1 x 10- pin flat cable with 2x5 2.54 mm connector 1 x 10-pin flat cable with 2x5 1.27 mm connector 1 x Converter board 2.54 mm – 1.27 mm connector 1 x Mini USB cable Batteries CD with Evaluation Version of the IAR EW8051 Documentation The hardware in this kit is FCC/IC certified and complies with ETSI/R&TTE over temperature from 0 to +35°C. 2 Running the Preprogrammed Link Test 2.1 Introduction The CC2510 on the SmartRFCC2510 target board is preprogrammed with a link test which operates at 2.42575 GHz, and uses GFSK modulation and a bit rate of 2.4 kbps. The link test runs a point-to-point communication between a Slave and a Master node based on the SimpliciTI 1.1.0 protocol. First the Master and Slave nodes must be configured as described in the following sections. The two nodes will then establish a link. When this link is established, the Master starts to periodically send packets to the Slave. Between each transmission, the Master goes to receive mode and waits 250 ms for an acknowledgement packet from the Slave. The Slave node is in receive mode waiting for packets from the Master. For each received packet, the Slave automatically responds with an acknowledgement packet. 2.2 Powering the boards Place 2 AAA batteries in the battery holder placed on the bottom side of each of the SmartRFCC2510 boards. Place the jumper on the power selection connector P1 between pin 1 and pin 2 on each board. Applying power to the SmartRFCC2510 starts the preprogrammed link test on the CC2510 and the two LEDs on the board are on for 1 s. 2.3 Configure the Master Node Press the MASTER button that is placed on the left hand side of the board. When this button is pushed, the two LEDs on the board will blink rapidly. The Master now waits for a Slave node to establish a link. Note that the board only responds to the first button push. To reconfigure the board, the board must be reset, see point 2.8 in this manual. 2.4 Configure the Slave Node On the other board, press the SLAVE button that is placed on the right side of the board. When the button has been pushed, the two LEDs on this board will blink very slowly until a link with a Master node is established. Note that establishing the link may finish in less than 1 s depending on the environment. 2.5 The LEDs on the Master Node LEDs State Both LEDs blink rapidly The Master is trying to establish a link with a Slave Green LED on for 0.5 s The Master has received an ACK to a packet sent, link ok Red LED on for 0.5 s The Master has not received an ACK to the last 3 packets sent Red LED on for 3 s If the Master does not receive ACKs from the SLAVE in ~70 s, the Master will stop to send packets to save power. Press S1/MASTER to resume the link test Red LED on for 5 s For test only: When the link is established, pressing the S2/SLAVE button turns the red LED on for 5 s 2.6 The LEDs on the Slave node LEDs State Both LEDs blink slowly The Slave is trying to establish a link with a Master Red LED on continuously The link between the Slave and Master is established and the Slave is in RX waiting for packets from the Master Green LED on for 0.5 s while red LED on continuously The Slave has received a packet from the Master and sent an ACK, link is good FCC/IC Regulatory Compliance FCC Part 15 Class A Compliant IC ICES-003 Class A Compliant
SWRU235B August 2013 2.7 Range testing The preprogrammed link test is well suited for range testing. Place the Slave in an open field and bring the Master a known distance away. Use the LED signaling to decide the link quality. Note that the environment, antenna, etc greatly affect the range, see DN018 www.ti.com/lit/swra169. 2.8 Resetting the board The recommended reset sequence is:  Remove jumper on P1 completely  Push one of the buttons to discharge the large capacitor on the power line. If this capacitor is not discharged, the SmartRFCC2510 boards may continue to run the current application until the capacitor is discharged. This may take several seconds.  Replace the jumper on P1 to power the board again 3 Using the CC Debugger with the Development Kit 3.1 The CC Debugger The CC Debugger connects to the PC via a mini USB and uses the DEBUG interface to communicate with the radio. The tool can be used for:  Programming the flash and debugging an application running on the CC2510. The PC tools available for these purposes are the SmartRF Flash Programmer from Texas Instruments and IAR Embedded Workbench for 8051 from IAR Systems.  Testing the radio performance of CC2510 using SmartRF Studio. For more details, please refer to the CC Debugger User’s Guide www.ti.com/lit/swru197 and the CC1110 & CC2510 Mini Development Kit User’s Guide www.ti.com/lit/swru236. 3.2 SmartRF Studio SmartRF Studio can be used for RF testing, evaluation of CC2510 and to find optimal register settings. It is available on http://www.ti.com/smartrfstudio. 3.3 Flash Programmer The Flash Programmer application, available on the kit web page http://focus.ti.com/docs/toolsw/folders/print/flash-programmer.html can be used to program Intel HEX files, read the contents of CC2510 flash, and several other operations. 3.4 IAR Embedded Workbench To develop software, program and debug the CC2510, the IAR Embedded Workbench for 8051 is recommended. An evaluation version of IAR EW8051 is included in the kit. This free evaluation version and also a free code size limited version, can also be downloaded from the web, see www.iar.com/ew8051. A. Available Software and User’s Guides CC1110 & CC2510 Mini DK Software Example User’s Guide and Source Code Source and documentation for the link test for the SmartRFCC2510 target board www.ti.com/lit/zip/swrc133 and www.ti.com/lit/swru237 CC1110 & CC2510 Mini Development Kit User’s Guide More documentation and details on the use of the SmartRFCC2510 target board www.ti.com/lit/swru236 CC1110, CC2510 Basic Software Examples Source code for other, simple examples for the CC2510 www.ti.com/lit/zip/swrc117 SimpliciTI™ Network Protocol An RF protocol targeting simple, small RF networks www.ti.com/simpliciti B. More information The Low Power RF Online Community www.ti.com/lprf-forum has forums, blogs and videos. Use the forums to find information, application and design notes, FAQs, or to discuss and get help with your design. On the Texas Instruments’ Low-Power RF web site www.ti.com/lprf, you will find all our latest products, news and events updates, and much more. The TI LPRF eNewsletter keeps you up to date on e.g. new products, application notes, software and events. Sign up at www.ti.com/lprfnewsletter We hope you will enjoy working with the C2510 Mini Development Kit and associated Low-Power RF products from Texas Instruments.
Download:
Mirror Download [FCC.gov]
Document ID2060090
Application ID/YNkI0WGTKbQCat2KaDL2g==
Document DescriptionUser manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize36.52kB (456508 bits)
Date Submitted2013-09-03 00:00:00
Date Available2013-09-03 00:00:00
Creation Date2013-08-23 16:37:02
Producing SoftwareMicrosoft® Word 2010
Document Lastmod2013-08-23 16:37:03
Document TitleCC2510 Mini Development Kit
Document CreatorMicrosoft® Word 2010
Document Author: TI User
FCC ID Filing: ZAT2510SRF

Navigation menu