Texas Tlc3578Evm Users Manual TLC3578 EVM Family Guide

Texas-Instruments-Tlc3578Evm-Users-Manual-400244 texas-instruments-tlc3578evm-users-manual-400244

TLC3578EVM to the manual d61d25e5-a0e2-4f77-9bb0-ffc8eec23587

: Texas Texas-Tlc3578Evm-Users-Manual-390438 texas-tlc3578evm-users-manual-390438 texas pdf

Open the PDF directly: View PDF .
Page Count: 32

TLC3578EVM Family

August 2003 Data Acquisition−Digital/Analog Converters

User’s Guide

SLAU110

IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,

enhancements, improvements, and other changes to its products and services at any time and to discontinue

any product or service without notice. Customers should obtain the latest relevant information before placing

orders and should verify that such information is current and complete. All products are sold subject to TI’s terms

and conditions of sale supplied at the time of order acknowledgment.

TI warrants performance of its hardware products to the specifications applicable at the time of sale in

accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI

deems necessary to support this warranty. Except where mandated by government requirements, testing of all

parameters of each product is not necessarily performed.

TI assumes no liability for applications assistance or customer product design. Customers are responsible for

their products and applications using TI components. To minimize the risks associated with customer products

and applications, customers should provide adequate design and operating safeguards.

TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,

copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process

in which TI products or services are used. Information published by TI regarding third−party products or services

does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.

Use of such information may require a license from a third party under the patents or other intellectual property

of the third party, or a license from TI under the patents or other intellectual property of TI.

Reproduction of information in TI data books or data sheets is permissible only if reproduction is without

alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction

of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for

such altered documentation.

Resale of TI products or services with statements different from or beyond the parameters stated by TI for that

product or service voids all express and any implied warranties for the associated TI product or service and

is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.

Following are URLs where you can obtain information on other Texas Instruments products & application

solutions:

Products Applications

Amplifiers amplifier.ti.com Audio www.ti.com/audio

Data Converters dataconverter.ti.com Automotive www.ti.com/automotive

DSP dsp.ti.com Broadband www.ti.com/broadband

Interface interface.ti.com Digital Control www.ti.com/digitalcontrol

Logic logic.ti.com Military www.ti.com/military

Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork

Microcontrollers microcontroller.ti.com Secruity www.ti.com/security

Telephony www.ti.com/telephony

Video & Imaging www.ti.com/video

Wireless www.ti.com/wireless

Mailing Address: Texas Instruments

Post Office Box 655303 Dallas, Texas 75265

Copyright  2003, Texas Instruments Incorporated

EVM IMPORTANT NOTICE

Texas Instruments (TI) provides the enclosed product(s) under the following conditions:

This evaluation kit being sold by TI is intended for use for ENGINEERING DEVELOPMENT OR EVALUATION

PURPOSES ONLY and is not considered by TI to be fit for commercial use. As such, the goods being provided

may not be complete in terms of required design-, marketing-, and/or manufacturing-related protective

considerations, including product safety measures typically found in the end product incorporating the goods.

As a prototype, this product does not fall within the scope of the European Union directive on electromagnetic

compatibility and therefore may not meet the technical requirements of the directive.

Should this evaluation kit not meet the specifications indicated in the EVM User’s Guide, the kit may be returned

within 30 days from the date of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE

WARRANTY MADE BY SELLER TO BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED,

IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY

PARTICULAR PURPOSE.

The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user

indemnifies TI from all claims arising from the handling or use of the goods. Please be aware that the products

received may not be regulatory compliant or agency certified (FCC, UL, CE, etc.). Due to the open construction

of the product, it is the user’s responsibility to take any and all appropriate precautions with regard to electrostatic

discharge.

EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH ABOVE, NEITHER PARTY SHALL BE LIABLE

TO THE OTHER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.

TI currently deals with a variety of customers for products, and therefore our arrangement with the user is not

exclusive.

TI assumes no liability for applications assistance, customer product design, software performance, or

infringement of patents or services described herein.

Please read the EVM User’s Guide and, specifically, the EVM Warnings and Restrictions notice in the EVM

User’s Guide prior to handling the product. This notice contains important safety information about temperatures

and voltages. For further safety concerns, please contact the TI application engineer.

Persons handling the product must have electronics training and observe good laboratory practice standards.

No license is granted under any patent right or other intellectual property right of TI covering or relating to any

machine, process, or combination in which such TI products or services might be or are used.

Mailing Address:

Texas Instruments

Post Office Box 655303

Dallas, Texas 75265

Copyright  2003, Texas Instruments Incorporated

EVM WARNINGS AND RESTRICTIONS

It is important to operate this EVM within the input voltage range of 15 V.

Exceeding the specified input range may cause unexpected operation and/or irreversible

damage to the EVM. If there are questions concerning the input range, please contact a TI

field representative prior to connecting the input power.

Applying loads outside of the specified output range may result in unintended operation and/or

possible permanent damage to the EVM. Please consult the EVM User’s Guide prior to

connecting any load to the EVM output. If there is uncertainty as to the load specification,

please contact a TI field representative.

During normal operation, some circuit components may have case temperatures greater than

60°C. The EVM is designed to operate properly with certain components above 60°C as long

as the input and output ranges are maintained. These components include but are not limited

to linear regulators, switching transistors, pass transistors, and current sense resistors. These

types of devices can be identified using the EVM schematic located in the EVM User’s Guide.

When placing measurement probes near these devices during operation, please be aware

that these devices may be very warm to the touch.

Mailing Address:

Texas Instruments

Post Office Box 655303

Dallas, Texas 75265

Copyright  2003, Texas Instruments Incorporated

How to Use This Manual

v

Preface

Read This First

About This Manual

This user’s guide describes the characteristics, operation, and use of

the following evaluation boards:

-TLC3578 EVM Bipolar-Input, 8-channel 14-bit serial analog-to-digital

converter

-TLC3574 EVM Bipolar-Input, 4-channel 14-bit serial analog-to-digital

converter

-TLC3548 EVM Unipolar-Input, 8-channel 14-bit serial analog-to-digital

converter

-TLC3544 EVM Unipolar-Input, 4-channel 14-bit serial analog-to-digital

converter

-TLC2578 EVM Bipolar-Input, 8-channel 12-bit serial analog-to-digital

converter

-TLC2574 EVM Bipolar-Input, 4-channel 12-bit serial analog-to-digital

converter

A complete circuit description as well as schematic diagram and bill of

materials is included. Contact the Product Information Center or e-mail

dataconvapps@list.ti.com for questions regarding this EVM.

How to Use This Manual

This document contains the following chapters:

-Chapter 1—EVM Overview

-Chapter 2—Analog Interface

-Chapter 3—Digital Interface

-Chapter 4—Power Supply

-Chapter 5—Getting the Most From Your EVM

-Chapter 6—Bill of Materials, Board Layouts, and Schematic

Trademarks

vi

FCC Warning

This equipment is intended for use in a laboratory test environment only. It

generates, uses, and can radiate radio frequency energy and has not been

tested for compliance with the limits of computing devices pursuant to subpart

J of part 15 of FCC rules, which are designed to provide reasonable protection

against radio frequency interference. Operation of this equipment in other

environments may cause interference with radio communications, in which

case the user at his own expense will be required to take whatever measures

may be required to correct this interference.

Trademarks

TI logo is a trademark of Texas Instruments.

Related Documentation From Texas Instruments

To obtain a copy of any of the following TI documents, call the Texas

Instruments Literature Response Center at (800) 477−8924 or the Product

Information Center (PIC) at (972) 644−5580. When ordering, please identify

this booklet by its title and literature number. Updated documents can also be

obtained through our website at www.ti.com.

Data Sheets Literature Number

TLC3578 SLAS262

TLC3574

TLC2578

TLC2574

TLC3548 SLAS266

TLC3544

OPA132 PDS1309

REF3040 SBVS032

REF3033

Contents

vii

Contents

1 EVM Overview 1-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.1 Features 1-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2 Analog Interface 2-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.1 Analog Interface Block Diagram 2-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.2 Signal Conditioning 2-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.3 Single Supply Operation 2-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.4 Physical Pinout Description 2-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.5 Reference Voltage 2-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.6 Configuration Options 2-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3 Digital Interface 3-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.1 Physical Pinout Description 3-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4 Power Supply 4-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5 Getting the Most From Your EVM 5-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.1 Additional Hardware Options 5-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.1.1 Stand-Alone EVM 5-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.1.2 DSP Interface 5-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.1.3 MSP430 Microcontroller interface 5-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6 Bill of Materials, Board Layouts, and Schematic 6-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6.1 Bill of Materials for EVM 6-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6.2 Board Layouts 6-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6.3 EVM Schematic 6-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Contents

viii

Figures

2−1 Block Diagram 2-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5−1 EVM Selection 5-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5−2 DSK-To-EVM Stackup Diagram 5-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6−1 Top Layer 6-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6−2 Internal Plane 1 6-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6−3 Internal Plane 2 6-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6−4 Bottom Layer (Mirrored) 6-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Tables

2−1 Analog Input Pinout Description 2-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2−2 ADC Reference Voltage 2-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2−3 Jumper Settings 2-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3−1 Digital Signal Pinout Description 3-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4−1 Power Connector Pinout Description 4-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-1

EVM Overview

EVM Overview

Each evaluation board is based on the equivalent ADC. All ADCs use a

synchronous serial interface which can be simply interfaced to many micro-

controllers using the SPI protocol.

Each EVM also incorporates a stable voltage reference, and operational

amplifier to ensure a low-noise voltage reference for the ADC.

Topic Page

1.1 Features 1-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Chapter 1

Features

1-2

1.1 Features

-Evaluation board featuring one of the following:

JTLC3578 ADC (order TLC3578 EVM)

JTLC3574 ADC (order TLC3574 EVM)

JTLC3548 ADC (order TLC3548 EVM)

JTLC3544 ADC (order TLC3544 EVM)

JTLC2578 ADC (order TLC2578 EVM)

JTLC2574 ADC (order TLC2574 EVM)

-Onboard reference, with recommended buffer circuitry

-Suggested signal conditioning circuitry for 1 channel only

2-1

Analog Interface

Analog Interface

Topic Page

2.1 Analog Interface Block Diagram 2-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.2 Signal Conditioning 2-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.3 Single Supply Operation 2-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.4 Physical Pinout Description 2-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.5 ADC Reference Voltage 2-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.6 Configuration Options 2-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Chapter 2

Analog Interface Block Diagram

2-2

2.1 Analog Interface Block Diagram

A block diagram for the analog interface of the EVM is shown in Figure 2−1.

Figure 2−1. Block Diagram

TLC3578

TLC3574

TLC3548

TLC3544

TLC2578

TLC2574

Signal

Conditioning

P1 / J1

The channels are arranged to comply with the EVM standard developed for

data converters. This standard defines eight channels of analog I/O on each

EVM module.

2.2 Signal Conditioning

The facility exists for the signal connected to channel 0 to be conditioned via

an operational amplifier. The amplifier present on the EVM operates from a

dual power supply and is configured with a gain of +1.

If signal conditioning is not required, it can easily be bypassed via a shorting

bar.

2.3 Single Supply Operation

Should the user wish to operate the amplifier from a single suply rail, this is also

possible by simply removing the dual supply amplifier and replacing it with a

suitable single supply alternative, for example the OPA353.

The suggested procedure is detailed below:

-Carefully desolder amplifier, U1

-Replace with a suitable single-supply alternative, for example TI part num-

ber OPA353UA

-Install appropriate resistor at R9

-Install appropriate capacitor at C11

-Install shorting bar at W1

Physical Pinout Description

2-3

Analog Interface

2.4 Physical Pinout Description

Samtec part numbers SSW-110-22-F-D-VS-K and TSM-110-01-T-DV-P

provide a convenient 10-pin dual row header/socket combination at P1. This

header/socket provides access to the analog input pins of the TLV2553/6.

Consult Samtec at www.samtec.com or 1−800−SAMTEC−9 for a variety of

mating connector options.

Table 2−1.Analog Input Pinout Description

Pin Number

Header Socket Signal Description

P1.2 J1.2 CH0 Channel 0 input, can be direct from P1/J1 connector or through Op-Amp

P1.4 J1.4 CH1 Channel 1 input, direct from P1/J1 connector

P1.6 J1.6 CH2 Channel 2 input, direct from P1/J1 connector

P1.8 J1.8 CH3 Channel 3 input, direct from P1/J1 connector

P1.10 J1.10 CH4 Channel 4 input, direct from P1/J1 connector

P1.12 J1.12 CH5 Channel 5 input, direct from P1/J1 connector

P1.14 J1.14 CH6 Channel 6 input, direct from P1/J1 connector

P1.16 J1.16 CH7 Channel 7 input, direct from P1/J1 connector

P1.18 J1.18 REF−External Reference negative input

P1.20 J1.20 REF+ External Reference positive input

2.5 Reference Voltage

The accuracy of conversion from a SAR ADC depends directly upon the

accuracy of the reference voltage. It is very important, therefore, that the

reference be stable, accurate and low drift.

The ADC reference pin presents a dynamic capacitive load to the amplifier.

The voltage supplied to the ADC must be capable of driving this dynamic load

properly, ensuring that the reference remain stable regardless of load.

The bipolar and unipolar devices are specified to use a different voltage for the

reference pin.

Table 2−2.ADC Reference Voltage

ADC Reference Voltage

Bipolar input

TLC3578 3.3 V

TLC3574 3.3 V

TLC2578 3.3 V

TLC2574 3.3 V

Unipolar input

TLC3548 4.096 V

TLC3544 4.096 V

Configuration Options

2-4

2.6 Configuration Options

There are a number of options available via shorting jumpers. These are

detailed below:

Table 2−3.Jumper Settings

Reference

Designator Description

Factory Set

Condition

Position Optional Position

Designator

1−2 2−3

W1 Single supply operation Not installed

W2 Select negative supply for op amp −Vs AGND (0 V)

W3 Select positive supply for op amp +Vs +Vcc (5 V)

W4 Select signal source for channel 0 Signal is via op amp Signal is directly from P1.2

W5 Select positive voltage reference Onboard reference Reference via P1.18

W6 Select digital power 5 V 3.3 V

W7 Select negative voltage reference Onboard reference Reference via P1.20

W8 CSTART, initiate manual conversion Disabled Enabled

W9 FS mode Disabled Enabled

W10 Device always selected Disabled Enabled

3-1

Digital Interface

Digital Interface

The digital interface for the EVM is simply the appropriate digital signals from

the ADC routed and presented to the 20-pin digital interface connector.

Topic Page

3.1 Physical Pinout Description 3-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Chapter 3

Physical Pinout Description

3-2

3.1 Physical Pinout Description

The EVM is designed for easy interfacing to multiple platforms. Samtec part

numbers SSW-110-22-F-D-VS-K and TSM-110-01-T-DV-P provide a

convenient 10-pin dual row header/socket combination.

This header/socket combination provides access to the digital control and

serial data pins of the EVM. Consult Samtec at www.samtec.com or

1−800−SAMTEC−9 for a variety of mating connector options.

Table 3−1.Digital Signal Pinout Description

Pin Number

Header Socket Signal Description

P3.1 J3.1 CS Chip select selects the device for data transfer.

P3.3 J3.3 SCLK/CLKX Data transfer clock

P3.5 J3.5 Reserved

P3.7 J3.7 FSX

P3.9 J3.9 FSR

P3.11 J3.11 SDI Serial data into the device

P3.13 J3.13 SDO Serial data out of the device

P3.15 J3.15 EOC or INT/EOC†Selects either EOC or INT − see data sheet for details.

P3.17 J3.17 Reserved

P3.19 J3.19 CSTART Control the beginning of a conversion

†Programmable as either EOC or INT

4-1

Power Supply

Power Supply

The EVM accepts four power supplies.

-A dual ± Vs dc supply for the dual-supply op-amps.

-A single 5.0 V dc supply for the analog section of the ADC.

-A single 3.3 V to 5 V dc supply for the digital section of the ADC.

There are two ways to provide these voltages.

-Hook-up the test points on the EVM. The test points are clearly labeled

+Vdd (3.3 V to 5 V), +5VA, +Vs (up to 18 V depending upon the amplifiers)

and –Vs (up to –18 V depending upon the amplifiers).

-Use the power connector P5/J5 and derive the voltages elsewhere.

The pinout for this connector is shown in Table 4−1.

Table 4−1.Power Connector Pinout Description

Signal P5/J5 Pin Number Signal

+VA 1 2 −VA

+5VA 3 4 −5VA

AGND 5 6 DGND

+1.8VD 7 8 VD1

+3.3VD 9 10 +5VD

Chapter 4

4-2

5-1

Getting the Most From Your EVM

Getting the Most From Your EVM

A wide range of prototyping options and software solutions are available from

TI, and offer additional flexibility, reducing your time-to-market. Hardware and

software offerings from TI help you easily get from concept to hardware and

software prototype.

Topic Page

5.1 Additional Hardware Options 5-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Chapter 5

Additional Hardware Options

5-2

5.1 Additional Hardware Options

In general there are three hardware directions that the user can take with the

EVM.

5.1.1 Stand-Alone EVM

The EVM can be used on its own. Using the EVM in this manner obliges the

user to provide a custom digital interface between the EVM and a host system.

Users are entirely responsible for ensuring proper timing requirements are met

in addition to providing any glue logic necessary. Users must also provide the

necessary analog interface and supply power to the EVM.

5.1.2 DSP Interface

Depending upon the DSP that the user chooses, there are a number of TI

DSKs available. DSKs are DSP Starter Kits, and provide users with a DSP

starter system. They contain all the necessary hardware and software to

quickly begin prototype construction.

For example, the TMS320C6711 DSP starter kit includes the DSK hardware,

a parallel port cable to connect to a PC, a 5-V universal power supply, and a

Code Composer Studio CD-ROM containing all the necessary software.

Each family of DSKs provides different physical interface options. These

interface options enable address, data, and control signals to be decoded and

used by mezzanine-level cards (such as EVMs).

To connect this EVM to any DSK requires selection of the correct interface

card. Generally the procedure is outlined below.

-Select the DSP you wish to use.

-Select the appropriate DSK.

-Select the suitable interface card.

As an example, assume that the user wishes to use the TLC3578 EVM with

the TMS320C6711 DSP, the steps that should be taken are shown below

following a side-elevation of the boards required.

Additional Hardware Options

5-3

Getting the Most From Your EVM

Figure 5−1. EVM Selection

TMS320C6711

DSK

TMS320C3000

Interface Card

TMS320C6711

DSP TLC3578 EVM

TLC3574 EVM

TLC3544 EVM

TLC3548 EVM

TLC3578 EVM

TLC3574 EVM

TMS320C5K / 6K

Interface Card

1. Select DSP 2. Select DSK 3. Select Interface Card.

TMS320C2000

Interface Card

Figure 5−2. DSK-To-EVM Stackup Diagram

Amplifier Site

Evaluation Module Site

DSK

C5K / 6K

Interface Card

C5K / 6K

Interface Card

80-Pin DSK Common Connector

5.1.3 MSP430 Microcontroller interface

TI also offer a range of low-power microcontrollers that have an SPI

interface. You can check-out these devices and order evaluation

modules at www.ti.com

A microcomputer evaluation board exists, featuring the MSP430F449

that also enables the ADC EVMs to be connected directly.

The HPA449 evaluation board, available from Softbaugh

www.softbaugh.com includes the following features:

5-4

6-1

Bill of Materials, Board Layouts, and Schematic

Bill of Materials, Board Layouts, and

Schematic

This chapter contains the EVM bill of materials, board layouts and schematics.

Topic Page

6.1 Bill of Materials for EVM 6-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6.2 Board Layouts 6-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6.3 EVM Schematic 6-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Chapter 6

Bill of Materials for EVM

6-2

6.1 Bill of Materials for EVM

Item

no. Qty Value Ref Des Description Vendor Part number

1 1 0R R19 Resistor, 0−Ω 1/16 W 5%

0402 SMD Panasonic ERJ−2GE0R00X

2 2 0R R8, R17 Resistor, 0−Ω 1/8 W 5%

1206 SMD Panasonic ERJ−8GEY0R00V

3 1 10R R15 Resistor 10−Ω 1/8 W 5%

1206 SMD Panasonic ERJ−8GEYJ100V

4 9 33R R1, R2, R3,

R4, R5, R6,

R7, R12, R13

Resistor, 33−Ω 1/8 W 5%

1206 SMD Panasonic ERJ−8GEYJ330V

5 4 100R R10, R11,

R20, R21 Resistor, 100−Ω 1/8 W 5%

1206 SMD Panasonic ERJ−8GEYJ101V

6 2 10 KΩR16, R18 Resistor, 10−kΩ, 1/8 W

5% 1206 SMD Panasonic ERJ−8GEYJ103V

7 1 10 pF C3 Capacitor, 10−pF 50 V

Ceramic chip, 0805 SMD Panasonic ECJ−2VC1H100D

8 8 0.1 µF C1, C13, C15,

C16, C20,

C22, C23,

C24

Capacitor, .1−µF 25 V

Ceramic, X7R 0805 Panasonic ECJ−2VB1E104K

9 8 27 nF C4, C5, C6,

C7, C8, C9,

C10, C14

Capacitor, 27000−pF 50 V,

Ceramic, X7R 0805 Panasonic ECJ−2VB1H273K

10 1 1 µF C18 Capacitor, 1−ìF 10 V J

Ceramic X5R 0805 Panasonic ECJ−2YB1A105K

11 1 10 µF C17 Capacitor, 10−µF 16 V

tantalum, TE series Panasonic ECS−T1CX106R

12 4 10 µF C2 C12 C19

C21 Capacitor, 10−µF 16 V,

VS electrolytic, SMD Panasonic ECE−V1CA100SR

13 2 W1, W10 2−pin header Samtec TSW−102−07−L−S

14 8 W2, W3, W4,

W5, W6, W7,

W8, W9

3−Pin header Samtec TSW−103−07−L−S

15 1 P5 10−Pin header Samtec TSM−105−01−T−DV−

P

16 1 J5 10−Socket strip Samtec SSW−105−22−F−D−

VS−K

17 4 P1 P2 P3 P4 20−Pin header Samtec TSM−110−01−T−DV−

P

18 4 J1 J2 J3 J4 20−Socket strip Samtec SSW−110−22−F−D−

VS−K

19 3 FB1, FB2,

FB3 Fair−Rite SM beads

#24−−44447 Fair-Rite 2744044447

20 2 OPA132UA U1, U3 IC, FET−input op amp,

8−SOIC Texas

Instruments OPA132UA

21 1 REF3033 U2 IC voltage reference,

3.33−V LP SOT−23 Texas

Instruments REF3033AIDBZT

Contingent on

Item 22 REF3040 U2 IC, voltage reference,

4.096−V, LP SOT−23 Texas

Instruments REF3040AIDBZT

Bill of Materials for EVM

6-3

Bill of Materials, Board Layouts, and Schematic

22 1 TLC3578 U4 IC, A/D 8−CH, 14−BIT,

LP 24−TSSOP Texas

Instruments TLC3578IPW

Alternate TLC3574 U4 IC, A/D, 4−Ch, 14−bit

LP 20−TSSOP Texas

Instruments TLC3574IPW

Alternate TLC3548 U4 IC, Unipolar A/D 8−CH

24−SOIC Texas

Instruments TLC3548IPW

Alternate TLC3544 U4 IC, Unipolar A/D 4−CH

20−SOIC Texas

Instruments TLC3544IPW

Alternate TLC2578 U4 IC, Serial out A/D 8−CH

24−SOIC Texas

Instruments TLC2578IPW

Alternate TLC2574 U4 IC, Serial out A/D 4−CH

20−TSSOP Texas

Instruments TLC2574IPW

23 2 SN74LVC1

G07 U5, U6 Single IC buffer driver

with open drain o/p Texas

Instruments SN74LVC1G07DBVR

24 1 TLC3578 Rev A PWB Texas

Instruments 6448024

25 4 TP_.025 +5VA, +VA,

−VA, Vdd Test Point − Single .025”

Pin Keystone

Electronics 5000

26 2 TP_turret AGND, DGND Turret terminal test point Cambion 180−7337−02−05

1 Not

Installed R14 * * *

1 Not

Installed C11 * * *

1 Not

Installed R9 * * *

Board Layouts

6-4

6.2 Board Layouts

Figure 6−1. Top Layer

Board Layouts

6-5

Bill of Materials, Board Layouts, and Schematic

Figure 6−2. Internal Plane 1

Figure 6−3. Internal Plane 2

Board Layouts

6-6

Figure 6−4. Bottom Layer (Mirrored)

EVM Schematic

6-7

Bill of Materials, Board Layouts, and Schematic

6.3 EVM Schematic

The EVM schematic is a PDF attachment following this page.

1 2 3 4 5 6

A

B

C

D

654321

D

C

B

Ati

12500 TI Boulevard. Dallas, Texas 75243

Title:

SHEET: OF:

FILE: SIZE:DATE:

REV:

21-Aug-2003

Drawn By:

Engineer:

Revision History

REV ECN Number Approved

TLC3578 EVM Block Diagram

DOCUMENTCONTROL #

TLC3578

TLC3578.sch

PWR & REF

PWR & REF.sch

CH6

CH7

AGND

1

3

5

7

9

11

13

17

19

2

4

6

8

10

12

14

16

18

20

15

P1

REF-

REF+

CH4

CH5

CH2

CH3

CH0

CH1

DGND

1

3

5

7

9

11

13

17

19

2

4

6

8

10

12

14

16

18

20

15

P3

GPIO_1

FSX

FSR

R17

0R

CLKX

CS*

DATA_IN

B_DATA_OUT

B_INT*/EOC

Joe Purvis

Joe Purvis

TLC3578 EVM Block Diagram

2

1 3

6448025

1 2 3 4 5 6

A

B

C

D

654321

D

C

B

Ati

12500 TI Boulevard. Dallas, Texas 75243

Title:

SHEET: OF:

FILE: SIZE:DATE:

REV:

21-Aug-2003

Drawn By:

Engineer:

Revision History

REV ECN Number Approved

TLC3578.sch

DOCUMENTCONTROL #

AGND

DVdd

W5

R2

33R

AGND

R12

33R

AGND

R3

33R

AGND

R1

33R

AGND

R4

33R

AGND

R5

33R

AGND

R6

33R

AGND

R7

33R

AGND

W4

CH0

CH1

CH2

CH3

CH4

CH5 REF+

W7

REF-

AGND

-In

2

+In

3

Output 6

74

U1

R9

Not Installed

R8

0R

AGND

CH0

CH7

CH6

VREF+

INT*/EOC

Amplifier +Supply

Amplifier -Supply

6448025 2

23

Joe Purvis

Joe Purvis

C10

27nF

C9

27nF

C8

27nF

C7

27nF

C6

27nF

C5

27nF

C4

27nF

C11

Not Installed

C14

27nF

R13

33R

DATA_OUT

DATA_IN

W1

BCLK

C15

0.1uF

+C17

10uF

C18

1uF

CS*

REF_M

REF_P

TLC3578

CLKX

AIN0

9

AIN1

10

AIN2

11

AIN3

12

AIN4

13

AIN5

14

AIN6

15

AIN7

16

AVdd 17

AGND

18

AGND

22

DVdd 7

DGND

6

REFM 20

REFP 19

CS* 8

SDO 5

SDI 3

SCLK 1

INT* / EOC 4

AVdd 23

COMP

21

CSTART* 24

FS 2

U4

TLC3578

+5V_s

C20

0.1uF

DGND

CSTART*

W8

R16

10K

DVdd

CSTART*

W9

FS

FS

R18

10K

DVdd

FSX

W10

CS*

DGND

GPIO_1

2 4

A Y

U5A

SN74LVC1G07

REF_M

REF_P

B_INT*/EOC

B_DATA_OUT

R21

100R

R20

100R

DVdd DVdd

2 4

A Y

U6A

SN74LVC1G07

1 2 3 4 5 6

A

B

C

D

654321

D

C

B

Ati

12500 TI Boulevard. Dallas, Texas 75243

Title:

SHEET: OF:

FILE: SIZE:DATE:

REV:

21-Aug-2003

Drawn By:

Engineer:

Revision History

REV ECN Number Approved

PWR & REF.sch

DOCUMENTCONTROL #

W2

W3

C16

0.1uF

+C19

10uF

C1

0.1uF

C13

0.1uF

+VA

-VA

+5VA

Amplifier +Supply

Amplifier -Supply

+C12

10uF

+

C2

10uF

+5V_s

+V_s

-V_s

FB3

FB2

FB1

AGND

AGND

AGND

AGND

-VA

+VA

+5VA

DGND AGND

W6

-In

2

+In

3

Output 6

74

U3

R11

100R

AGND

VREF+

Amplifier +Supply

Amplifier -Supply

C3

10pF

DGNDAGND

R14

Not Installed

R19

0R

AGND DGND

DVdd

Vdd

DGND

+C21

10uF

C22

0.1uF

12 34 56 78 910

P5

+3.3V_D

+5V_D

R15

10R

1

3

5

7

9

11

13

17

19

2

4

6

8

10

12

14

16

18

20

15

P2

1

3

5

7

9

11

13

17

19

2

4

6

8

10

12

14

16

18

20

15

P4

GND

3

Vcc 5

NC

1

U6B

SN74LVC1G07

C24

0.1uF

C23

0.1uF

GND

3

Vcc 5

NC

1

U5B

SN74LVC1G07

DVdd

DGND

DVdd

DGND

IN

1OUT 2

GND

3

U2

REF3040

+5V_s

Joe Purvis

Joe Purvis

TLC3578 EVM Power & Reference

2

3 3

6448025

R10

100R