The Sapling HPB-24G-1 2.4GHz FHSS TRANSCEIVER User Manual

The Sapling Company, Inc 2.4GHz FHSS TRANSCEIVER

Contents

User Manual OEM

OEM MANUAL
August 2013
2.433-2.449 GHz Frequency Hopping Transceiver Module
Model: D-CCA-HPB-24G-1
FCC ID: R73HPB-24G-1
REV 1
Page 2 of 8
OEM INTEGRATOR ATTESTATION
a. This module is for OEM installation only.
b. The OEM is responsible for ensuring that the end-user has no manual
instructions to remove or install module.
c. The module is limited to installation in mobile or fixed applications,
according to Part 2.1091(b).
d. Separate approval is required for all other operating configurations,
including portable configurations with respect to Part 2.1093 and different
antenna configurations.
e. This module may only be used with antennas with a maximum gain of 2.15
dBi, including any replacement antennas, to maintain compliance and
satisfying RF exposure compliance.
f. Labeling instructions of finished products must be in accordance with the
requirements outlined in KDB784748 D01 v07, section 8. Page 6/7 last two
paragraphs which include the required instructions; example: “Contains
Transmitter Module FCC ID: XYZMODEL1” or “Contains FCC ID:
XYZMODEL1” and described herein.
g. The instructions/statements required per Part 15.19 and 15.21must be
included in the host user’s manual (i.e. end product).
Robert A. Bongiorno
Chief Engineer
The Sapling Company
robertb@sapling-inc.com
(215) 322 – 6063 x1114
Page 3 of 8
Introduction
This module is only authorized to be installed in fixed mount installation and may
not be installed in a mobile or portable device.
The HPB-24G-1 module is to be used in Sapling Master Clocks such as the SMA-
3000 or SMA Repeater and equivalent models.
The module is only to be connected to and installed in other Sapling products.
Specifications
The antenna gain is +2.15dBi maximum.
The maximum output power will be 30 dBm.
The transmit cycle is a sequence of 80 data strings on 76 different frequencies,
each transmitted for 3 msec.
Every transmit cycle is 240 msec in duration (80 x 3ms).
The frequency hopping pattern is proprietary to Sapling and covers the range from
2.433 to 2.449 GHz.
Connections
The picture shows the HPB-24G-1 RF module, connectors, and FCC ID label.
HPB-24G-1
P1
FCC ID: R73HPB-24G-1
P2
P1 POWER & DATA
P2 PROGRAMMING
Page 4 of 8
HPB-24G-1 Connectors
Installed
The picture on the next page shows the HPB-24G-1 RF module in a repeater. It
shows the SMA-1SR-G0000-1 and the connectors to the rest of the Sapling
Wireless Clock System.
P1 OPERATING CONNECTOR
5 VOLTS
GROUND
PPS OUT
TXD
RXD
MSTR/SLV
STBY
NO CONNECTION
* PIN 1 IS SQUARE PAD.
P2 PROGRAMMING CONNECTOR
TDO/TDI
3.3 VOLTS
TDI
3.3 VOLTS
TMS
NO CONNECTION
TCLK
TEST
GROUND
NO CONNECTION
RST
TXD
SHIELD
RXD
* PIN 1 IS SQUARE PAD.
P2 PROGRAMMING
P1 POWER & DATA
Page 5 of 8
SMA-1SR-G000-1
P1 OPERATING CONNECTOR
PIN 1
5 VOLTS RED WIRE
PIN 2
GROUND BLACK WIRE
PIN 3
PPS OUT
PIN 4
TXD ORANGE WIRE
PIN 5
RXD VIOLET WIRE
PIN 6
MSTR/SLV WHITE WIRE
PIN 7
STBY
PIN 8
NO CONNECTION
* PIN 1 IS SQUARE PAD.
FCC ID: R73HPB-24G-1
P1
P1 POWER & DATA
HPB-24G-1
5 VOLT POWER
SUPPLY
5 VOLT POWER
& DATA BOARD
Page 6 of 8
The picture below shows the top of the SMA-1SR-G000-1 with HPB-24G-1 RF
module antenna connector and the FCC ID and the Compliance Label.
SMA-1SR-G000-1
SMA-1SR-G000-1 Label
The label below is an example of the FCC ID and the Compliance Label.
Page 7 of 8
Installed
The picture below shows the HPB-24G-1 RF module in a master clock. It shows
the SMA-3S0-G008-1 and the connectors to the rest of the Sapling Wireless Clock
System.
SMA-3S0-G008-1
The picture below shows the top of the SMA-3S0-G008-1 with HPB-24G-1 RF
module antenna connector and the FCC ID and the Compliance Label.
SMA-3S0-G008-1
FCC ID: R73HPB-24G-1
HPB-24G-1
P1
P1 OPERATING CONNECTOR
5 VOLTS RED WIRE
GROUND BLACK WIRE
PPS OUT
TXD ORANGE WIRE
RXD VIOLET WIRE
MSTR/SLV WHITE WIRE
STBY
NO CONNECTION
* PIN 1 IS SQUARE PAD.
P1 POWER & DATA
5 VOLT POWER
SUPPLY
RELAY & CONTROL
BOARD
Page 8 of 8
SMA-3S0-G008-1 Label
The label below is an example of the FCC ID and the Compliance Label.
Operation
1. The HPB-24G-1 RF module, as a repeater transceiver, will receive time
from another transmitter or clock and re-transmit the time.
2. The HPB-24G-1 RF module, as a master clock transceiver, will transmit the
time for 240 msec and receive the time for up to 20 seconds once a minute.
FCC Statement:
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO
OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS
TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE
USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
“Changes Or Modifications Not Expressly Approved By The Party
Responsible For Compliance Could Void The User's Authority To Operate
The Equipment.”

Navigation menu