Topcon WT11EC Bluetooth Module User Manual

Topcon Corporation Bluetooth Module

a href="https://usermanual.wiki/Topcon" itemprop="url"> Topcon >

Users manual

WT11EC USER’S MANUAL Over View This device is a class 1,Bluetooth® 2.0+EDR (Enhanced Data Rates)module. Physical Specifications Table A-1 Physical Specification Dimensions W: 43mm D: 20mm H: 4.3mm Weight 4g Input / output UART interface/Power/antenna Input voltage 3.3V±5% Operating temperature -40 to +85℃ Storage temperature -40 to +85℃ Wireless specifications Table A-2 Wireless Specifications Standard Bluetooth Version 2.0 Class 1 Frequency modulation technique T GFSK(1Mbps), π/4 DQPSK(2Mbps), 8DPSK(3Mbps) Hopping 1600hops,1MHz channel space Frequency Range 2404-2478MHz Output power 12dBm Installation Guide 1. Module connected to UART Port on the mother Board in your Equipment. (see below) NAME SPEC MODEL I/F Connecter UART Port DF16-40DP-0.5v RF Connector Antenna coaxial connector U.FL-R-SMT *We are preparing driver software. Confirm the homepage of Microsoft to the method of installing the driver software. You must make sure that 20cm minimum separation is maintained between users and the antenna. Mother Board UART Port Bottom View Top View Connect to UARTPort Antenna
Warning Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Regulatory Information Compliance statement to FCC/IC This module complies with part 15 of the FCC rules and IC RSS-210. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RF exposure compliance 1) To comply with FCC/IC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. 2) This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Requirements to end product This module must be integrated only by OEM integrators under the following conditions. (1) OEM integrator has to be aware not provide information to the users regarding how to install or remove this module in the users manual of the end product which integrate this module. Installation by end users is strictly prohibited. (2) Antenna OEM integrator shall use this module without any modifications including antenna. If module integrator uses a unique antenna, the FCC certification is required for the end product. OEM integrator must make sure that 20cm minimum separation is maintained between users and the antenna. (3) Co-location. This module must not be co-located or operated in conjunction with any other antenna or transmitter. The module integrator shall obtain FCC approval for the end product, if the module is used for co-location operation. (4) Markings To satisfy FCC/IC exterior labeling requirements, the following text must be placed on the exterior of the end product. Contains Module FCC ID: H5P-WT11EC, IC: 6050A-WT11EC Any similar wording that expresses the same meaning may be used. (5) Caution to user for modification The following caution is expressed on the user’s instruction manual. The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the device. (6) Compliance statement to FCC The following statement is expressed on the user’s instruction manual.
Download:
Mirror Download [FCC.gov]
Document ID1217451
Application IDhtYPVNy6zZL6ZEmeLGvjgQ==
Document DescriptionUsers manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize6.99kB (87318 bits)
Date Submitted2009-12-22 00:00:00
Date Available2010-02-20 00:00:00
Creation Date2009-12-14 11:32:29
Producing SoftwareAcrobat Distiller 6.0 (Windows)
Document Lastmod2009-12-14 11:32:29
Document Titleuntitled
FCC ID Filing: H5P-WT11EC

Navigation menu