Toro 13BX60RG744 User Manual TRACTOR Manuals And Guides 1101331L

User Manual: Toro 13BX60RG744 13BX60RG744 TORO TRACTOR - Manuals and Guides View the owners manual for your TORO TRACTOR #13BX60RG744. Home:Lawn & Garden Parts:Toro Parts:Toro TRACTOR Manual

Open the PDF directly: View PDF .
Page Count: 36

Count on it.

k,.

k.,

Form No. 3357-948 Rev. A

LX42 Lawn Tractor

Model No. 13BX60RG744

Model No. 13BX60RG748

769-02824A (11/22/06)

California Proposition 65 Warning:

WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or

emit chemicals known to the State of California to cause cancer and birth defects or other

reproductive harm.

TABLEOFCONTENTS

Content Page

Important Safe Operation Practices 3

Slope Gauge 9

Tractor Set-up 10

Know Your Lawn Tractor 13

Operating Your Lawn Tractor 16

Making Adjustments 19

Maintaining Your Lawn Tractor 21

Content Page

Service 26

Off-season Storage 29

Maintenance Chart 30

Troubleshooting 31

Specifications 32

Warranty Information 35

FINDINGMODELNUMBER

This Operator's Manual is an important part of your new lawn tractor. It will help you assemble, prepare and maintain the

unit for best performance. Please read and understand what it says.

Before you start assembling your new equipment, please locate the model plate on the equipment and

copy the information from it in the space provided below. A sample model plate is also illustrated below. You

can locate the model plate by looking at the underside of the tractor's seat. This information will be necessary

to use the manufacturer's web site and/or help from an authorized Toro service dealer.

MODELNUMBER SERIALNUMBER DOM

THE TORO COMPANY

8111 LYNDALE AVE. SOUTH

BLOOMINGTON, MINNESOTA 55420-1196

TOLL FREE PHONE NUMBER: 1-888-384-9942 USA

%TOLL FREE PHONE NUMBER: 1-888-848-4073 Canada

Copy the model number here:

Copy the serial number here:

CUSTOMERSUPPORT

Please do NOT return the unit to the retailer without first contacting Customer Support. If you have difficulty

assembling this product or have any questions regarding the controls, operation or maintenance of this unit, you can

seek help from the experts. Choose from the options below:

Visit www.toro.com for many useful suggestions. Click on Customer Care in the Homeowners section of the Toro

Solutions Center and help is immediately available.

N}te Searc+h_ [ @ 8_

If you have questions concerning your tractor, please call us at 1-888-384-9942 (U.S.)

or 1-888-848-4073 (Canada).

SECTION1: IMPORTANTSAFEOPERATIONPRACTICES

WARNING: This symbol points out important safety instructions which, if not followed, could endanger

the personal safety and/or property of yourself and others. Read and follow all instructions in this manual

before attempting to operate this machine. Failure to comply with these instructions may result in personal

injury. When you see this symbol-heed its warning.

DANGER: This machine was built to be operated according to the rules for safe operation in this man-

ual. As with any type of power equipment, carelessness or error on the part of the operator can result in

serious injury. This machine is capable of amputating hands and feet and throwing objects. Failure to

observe the following safety instructions could result in serious injury or death.

WARNING: This unit is equipped with an internal combustion engine and should not be used on or near

any unimproved forest-covered, brush-covered or grass-covered land unless the engine's exhaust system

is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used,

it should be maintained in effective working order by the operator. In the State of California the above is

required by law (Section 4442 of the California Public Resources Code). Other states may have similar

laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through an

authorized Toro service dealer or contact Toro at 8111 Lyndale Avenue South, Bloomington, MN 55420.

GENERAL OPERATION

1. Read, understand, and follow all instructions on the

machine and in the manual(s) before attempting to

assemble and operate. Keep this manual in a safe

place for future and regular reference.

2. Be familiar with all controls and their proper

operation. Know how to stop the machine and

disengage PTO/blades quickly.

3. Never allow children under 14 years old to operate

this machine. Children 14 years old and over

should read and understand the operation

instructions and safety rules in this manual and

should be trained and supervised by a parent or

responsible adult.

4. Never allow adults to operate this machine without

proper instruction.

5. To help avoid blade contact or a thrown object

injury, keep bystanders, helpers, children and pets

at least 75 feet from the machine while it is in

operation. Stop machine if anyone enters the area.

6. Thoroughly inspect the area where the equipment

is to be used. Remove all stones, sticks, wire,

bones, toys, and other foreign objects which could

be picked up and thrown by the blade(s). Thrown

objects can cause serious personal injury.

7. Plan your mowing pattern to avoid discharge of

material toward roads, sidewalks, bystanders and

the like. Also, avoid discharging material against a

wall or obstruction which may cause discharged

material to ricochet back toward the operator.

8. Always wear safety glasses or safety goggles

during operation and while performing an

adjustment or repair to protect your eyes. Thrown

objects which ricochet can cause serious injury to

the eyes.

9. Wear sturdy, rough-soled work shoes and close-

fitting slacks and shirts. Loose fitting clothes and

jewelry can be caught in movable parts. Never

operate this machine in bare feet or sandals.

10. Be aware of the mower and attachment discharge

direction and do not point it at anyone. Do not

operate the mower without the discharge cover or

entire grass catcher in its proper place.

11. Do not put hands or feet near rotating parts or

under the cutting deck. Contact with the blade(s)

can amputate hands and feet.

12. A missing or damaged discharge cover can cause

blade contact or thrown object injuries.

13. Stop the blade(s) when crossing gravel drives,

walks, or roads and while not cutting grass.

14. Watch for traffic when operating near or crossing

roadways. This machine is not intended for use on

any public roadway.

15. Do not operate the machine while under the

influence of alcohol or drugs.

16. Mow only in daylight or good artificial light.

17. Never carry passengers.

18. Disengage blade(s) before shifting into reverse.

Back up slowly. Always look down and behind

before and while backing to avoid a back-over

accident.

19. Slow down before turning. Operate the machine

smoothly. Avoid erratic operation and excessive

speed.

20. Disengage blade(s), set parking brake, stop engine

and wait until the blade(s) come to a complete stop

before removing grass catcher, emptying grass,

unclogging chute, removing any grass or debris, or

making any adjustments.

21.Neverleavearunningmachineunattended.

Alwaysturnoffblade(s),placetransmissionin

neutral,setparkingbrake,stopengineandremove

keybeforedismounting.

22.Useextracarewhenloadingorunloadingthe

machineintoatrailerortruck.Thisunitshouldnot

bedrivenupordownramp(s),becausetheunit

couldtipover,causingseriouspersonalinjury.The

unitmustbepushedmanuallyonramp(s)to loador

unloadproperly.

23.Mufflerandenginebecomehotandcancausea

burn.Donottouch.

24.Checkoverheadclearancescarefullybeforedriving

underlowhangingtreebranches,wires,door

openingsetc.,wheretheoperatormaybestruckor

pulledfromtheunit,whichcouldresultinserious

injury.

25.DisengagethePTOandallattachmentclutches,

depressthebrakepedalcompletelyandshiftinto

neutralbeforeattemptingtostartengine.

26.Yourmachineisdesignedtocutnormalresidential

grassofaheightnomorethan10".Donotattempt

to mowthroughunusuallytall,drygrass(e.g.,

pasture)orpilesofdryleaves.Drygrassorleaves

maycontacttheengineexhaustand/orbuildupon

themowerdeckpresentingapotentialfirehazard.

27.Useonlyaccessoriesandattachmentsapproved

forthismachinebythemachinemanufacturer.

Read,understandandfollowallinstructions

providedwiththeapprovedaccessoryor

attachment.

28.Dataindicatesthatoperators,age60yearsand

above,areinvolvedinalargepercentageofriding

mower-relatedinjuries.Theseoperatorsshould

evaluatetheirabilitytooperatetheridingmower

safelyenoughtoprotectthemselvesandothers

fromseriousinjury.

29.Ifsituationsoccurwhicharenotcoveredinthis

manual,usecareandgoodjudgment.Contactan

authorizedToroservicedealerforassistance.

SLOPE OPERATION

Slopes are a major factor related to loss of control and

tip-over accidents which can result in severe injury or

death. All slopes require extra caution. If you cannot

back up the slope or if you feel uneasy on it, do not mow

it.

For your safety, use the slope gauge included as part of

this manual to measure slopes before operating this

unit on a sloped or hilly area. If the slope is greater than

15 degrees as shown on the slope gauge, do not

operate this unit on that area or serious injury could

result.

DO:

1. Mow up and down slopes, not across. Exercise

extreme caution when changing direction on

slopes.

2. Watch for holes, ruts, bumps, rocks, or other

hidden objects. Uneven terrain could overturn the

machine. Tall grass can hide obstacles.

3. Use slow speed. Choose a low enough speed

setting so that you will not have to stop or shift while

on the slope. Tires may lose traction on slopes

even though the brakes are functioning properly.

Always keep machine in gear when going down

slopes to take advantage of engine braking action.

4. Follow the manufacturer's recommendations for

wheel weights or counterweights to improve

stability.

5. Use extra care with grass catchers or other

attachments. These can change the stability of the

machine.

6. Keep all movement on the slopes slow and gradual.

Do not make sudden changes in speed or direction.

Rapid transmission engagement or braking could

cause the front of the machine to lift and rapidly flip

over backwards which could cause serious injury.

7. Avoid starting or stopping on a slope. If tires lose

traction, disengage the blade(s) and proceed

slowly straight down the slope.

DO NOT:

1. Do not turn on slopes unless necessary; then, turn

slowly and gradually downhill, if possible.

2. Do not mow near drop-offs, ditches or

embankments. The mower could suddenly turn

over if a wheel is over the edge of a cliff, ditch, or if

an edge caves in.

3. Do not try to stabilize the machine by putting your

foot on the ground.

4. Do not use a grass catcher on steep slopes.

5. Do not mow on wet grass. Reduced traction could

cause sliding.

6. Do not shift to neutral and coast downhill. Doing so

may cause the operator to lose control of the

machine resulting in serious injury or death.

7. Do not tow heavy pull behind attachments (e.g.

loaded dump cart, lawn roller, etc.) on slopes

greater than 5 degrees. When going down hill, the

extra weight tends to push the tractor and may

cause you to loose control. (e.g. tractor may speed

up, braking and steering ability are reduced,

attachment may jack-knife and cause tractor to

overturn).

CHILDREN

1. Tragic accidents can occur if the operator is not

alert to the presence of children. Children are often

attracted to the machine and the mowing activity.

They do not understand the dangers. Never

assume that children will remain where you last

saw them.

a. Keep children out of the mowing area and in

watchful care of a responsible adult other

than the operator.

b. Be alert and turn machine off if a child enters

the area.

c. Before and while backing, look behind and

down for small children.

d. Never carry children, even with the blade(s)

shut off. They may fall off and be seriously

injured or interfere with safe machine

operation.

e. Use extreme care when approaching blind

corners, doorways, shrubs, trees or other

objects that may block your vision of a child

who may run into the machine.

f. To avoid back-over accidents, always

disengage the cutting blade(s) before

shifting into reverse. The "Reverse

Caution Mode" should not be used when

children or others are around.

g. Keep children away from hot or running

engines. They can suffer burns from a hot

muffler.

h. Remove key when machine is unattended to

prevent unauthorized operation.

2. Never allow children under 14 years old to operate

the machine. Children 14 years old and over should

read and understand the operation instructions and

safety rules in this manual and should be trained

and supervised by a parent or responsible adult.

TOWING

1. Tow only with a machine that has a hitch designed

for towing. Do not attach towed equipment except

at the hitch point.

2. Follow the manufacturers recommendation for

weight limits for towed equipment and towing on

slopes.

3. Never allow children or others in or on towed

equipment.

4. Do not tow heavy pull behind attachments (e.g.

loaded dump cart, lawn roller, etc.) on slopes

greater than 5 degrees. When going down hill, the

extra weight tends to push the tractor and may

cause you to loose control. (e.g. tractor may speed

up, braking and steering ability are reduced,

attachment may jack-knife and cause tractor to

overturn).

5. Travel slowly and allow extra distance to stop.

6. On slopes, the weight of the towed equipment may

cause loss of traction and loss of control.

7. Do not shift to neutral and coast downhill.

SERVICE

SAFE HANDLING OF GASOLINE:

To avoid personal injury or property damage

use extreme care in handling gasoline. Gasoline is

extremely flammable and the vapors are explosive.

Serious personal injury can occur when gasoline is

spilled on yourself or your clothes which can ignite.

Wash your skin and change clothes immediately.

a. Use only an approved gasoline container.

b. Never fill containers inside a vehicle or on a

truck or trailer bed with a plastic liner. Always

place containers on the ground away from

your vehicle before filling.

c. When practical, remove gas-powered

equipment from the truck or trailer and refuel

it on the ground. If this is not possible, then

refuel such equipment on a trailer with a

portable container, rather than from a

gasoline dispenser nozzle.

d. Keep the nozzle in contact with the rim of the

fuel tank or container opening at all times

until fueling is complete. Do not use a nozzle

lock-open device.

e. Extinguish all cigarettes, cigars, pipes and

other sources of ignition.

f. Neverfuel machine indoors.

g. Never remove gas cap or add fuel while the

engine is hot or running. Allow engine to cool

at least two minutes before refueling.

h. Never over fill fuel tank. Fill tankto no more

thanl/2-inch below the bottom of the filler

neck to allow space for fuel expansion.

i. Replace gasoline cap and tighten securely.

j. If gasoline is spilled, wipe it off the engine

and equipment. Move unit to another area.

Wait 5 minutes before starting the engine.

k. To reduce fire hazards, keep machine free of

grass, leaves, or other debris build-up. Clean

up oil or fuel spillage and remove any fuel

soaked debris.

I. Never store the machine or fuel container

inside where there is an open flame, spark or

pilot light as on a water heater, space heater,

furnace, clothes dryer or other gas

appliances.

m. Allow a machine to cool at least 5 minutes

before storing.

GENERALSERVICE:

1. Never run an engine indoors or in a poorly

ventilated area. Engine exhaust contains carbon

monoxide, an odorless, and deadly gas.

2. Before cleaning, repairing, or inspecting, make

certain the blade(s) and all moving parts have

stopped. Remove the ignition key to prevent

unintended starting.

3. Periodically check to make sure the blades come to

complete stop within approximately five (5)

seconds after operating the blade disengagement

control. If the blades do not stop within the this time

frame, your unit should be serviced professionally

by an authorized Toro service dealer.

4. Check brake operation frequently as it is subjected

to wear during normal operation. Adjust and service

as required.

5. Check the blade(s) and engine mounting bolts at

frequent intervals for proper tightness. Also,

visually inspect blade(s) for damage (e.g.,

excessive wear, bent, cracked).

Replace the blade(s) with the original equipment

manufacturer's (O.E.M.) blade(s) only. Use of parts

which do not meet the original equipment

specifications may lead to improper performance

and compromise safety!

6. Mower blades are sharp. Wrap the blade or wear

gloves, and use extra caution when servicing them.

7. Keep all nuts, bolts, and screws tight to be sure the

equipment is in safe working condition.

8. Never tamper with the safety interlock system or

other safety devices. Check their proper operation

before each use.

9. After striking a foreign object, stop the engine and

remove the ignition key to prevent unintended

starting. Thoroughly inspect the machine for any

damage. Repair the damage before starting and

operating.

10. Never attempt to make adjustments or repairs to

the machine while the engine is running.

11. Grass catcher components and the discharge

cover are subject to wear and damage which could

expose moving parts or allow objects to be thrown.

12. For safety protection, frequently check components

and replace immediately with original equipment

manufacturer's (O.E.M.) parts only. Use of parts

which do not meet the original equipment

specifications may lead to improper performance

and compromise safety!

13. Do not change the engine governor settings or

over-speed the engine. The governor controls the

maximum safe operating speed of the engine.

14. Maintain or replace safety and instruction labels as

necessary (i.e. when scratched, damaged or

missing).

15. Observe proper disposal laws and regulations for

gas, oil, etc. to protect the environment.

WARNING: YOUR RESPONSIBILITY Restrict the use of this power machine to persons who agree to

read, understand and follow the warnings and instructions in this manual and on the machine.

SAFETYSYMBOLS

This operator's manual describes safety symbols and pictographs that may appear on this product.

Symbol Meaning

SAFETY ALERT SYMBOL --

Indicates Danger, Warning or Caution. May be used

in conjunction with other symbols or pictographs.

WARNING - READ OPERATOR'S MANUAL --

Read theOperator's Manual(s) and follow all warning

and safety instructions. Failure to do so can result in

seriousinjury to the operator and/or bystanders.

SECTION2: SAFETYANDINSTRUCTIONALLABELS

Safety and instructional abels found on your lawn tractor are illustrated below (3/4 actual size). Always follow their

instructions and heed their warnings. If you discover a safety label is scratched, damaged or missing, order a replacement

immediately.

ROTATING BLADES CAUSE

SERIOUS iNJURY OR DEATH

* DOHOTMOWWHEHCHILBREHOROTHERS

ABEABOUHB

*NEVEBCABBYCHILBBEHEVEHWiTHBLADE(S)

OFF,

* LOOKBOWHAHBBEHIHBBEFOREAHBWHILE

BACKIH6.

* MOWIH6IHREVERSEiSHOTBECOMMEHBEB.

t, DISENGAGEBLADE$/PTO,(POWERTAKEOFF)

2, ENGAGETHETRACTOR'SPARKINGBRAKE,

3, ACTIVATETHECHOKECOHTROL,

4, TURHKEYTOSTARTENGINE,AFTERSTARTRELEASEKEY& DEACTIVATECHOKE

BYPLACINGTHROTTLETOFAST"RABBIT"POSiTiON,

NOTE:IN BOTH MODES, WHEN OPERATOR LEAVES SEAT, ENGINE WILL

STOP UNLESS PARKING BRAKE IS SET AND BLADES ARE DISENGAGED.

Pad No. 112-1262

Part No. 112-1265

Part No. 112-1271

Pad No. 112-1274

Pad No. 112-1266

Pad No. 112-1270

Pad No. 112-1267

/_ DANGEF_PO|SON

_EXPL HIELD

EYES.

OSIVE

GASESCAN

CAUSEBLINDNESS

ORINJURY.

PROTEGERLES.

YEUX.LESGAZ

EXPLOSIFS.

PEUVENTBLESSER

OURENDREAVEUGLE,

Q SULFURICACIDCANCAUSE

NO BLINDNESS

, SPARKS

,FLAMES

*SMOKING

I_LOIGNERSULFURIQUE

PEUTCAUSER

, LESETINCELLESLACECI_'EOU

, LESFLAMMES DESBRULURES

,DEFUMER GRAVES.

FLUSHEYES

IMMEDIATELYWITH

WATER.GETMEDICAL

HELPFAST. _ ,_._

RINCE,ZLES

YEUXA L'EAU._

IMMEDIATEMENT.

CONS,ULTEZ

UN IV]EDECIN

RAPIDEMENT.

KEEPOUTOFTHEREACHOFCHILDREN.DO NOTTIP.DONOTOPENBATTERY!

TENIRHORSDELAPORTEEDESENFANTS.NEPASRENVERSER.NEPASOUVlRLABATTERIE!

SECTION3: SLOPEGAUGE

SECTION4: TRACTORSET-UP

AttachingTheSteeringWheel

ToolsRequired

(1) 1/2" socket wrench

1. The hardware for attaching the steering wheel has

been packed within the steering wheel, beneath

steering wheel cap. Carefully pry off the steering

wheel cap and remove the hardware.

2. With the wheels of the tractor pointing straight

forward, place the steering wheel over the steering

shaft.

3. Place the washer (with the cupped side down) over

the steering shaft and secure with the hex bolt. See

Figure 1.

Cap

........ SteeringShaft

Figure 1

Place the steering wheel cap over the center of the

steering wheel and push downward until it "clicks"

into place.

AttachingtheBatteryCables

Tools Required

(1) 7/16" wrench

WARNING: California Proposition 65

Warning: Battery posts, terminals, and

related accessories contain lead and lead

compounds, chemicals known to the State of

California to cause cancer and reproductive

harm. Wash hands after handling.

NOTE: Your tractor's battery cables may have

already be attached at the factory.

NOTE: The positive battery terminal is marked Pos.

(+). The negative battery terminal is marked Neg. (-).

• The positive cable (heavy red wire) is secured to

the positive battery terminal (+) with a carriage bolt

and hex nut at the factory. Make certain that the

rubber boot covers the terminal to help protect it

from corrosion.

• Remove the carriage bolt and hex nut from the

negative cable.

• Remove the black plastic cover, if present, from the

negative battery terminal and attach the negative

cable (heavy black wire) to the negative battery

terminal (-) with the bolt and hex nut.

• Make certain the hold-down rod is in position over

the battery, securing it in place. See Figure 2.

H01dDownRod

CarriageBolt \ HexNut

Figure 2

NOTE: If the battery is put into service after the date

shown on top/side of battery, charge the battery as

instructed on page 27 of this manual prior to operating

the tractor.

Tire Pressure

_. WARNING: Never exceed the maximum

inflation pressure shown on the sidewall of the

tire.

The tires on your unit may be over-inflated for shipping

purposes. Reduce the tire pressure before operating

the tractor. Recommended operating tire pressure is

approximately 10 p.s.i for the rear tires and 14 p.s.i, for

the front tires. Check sidewall of tire for maximum p.s.i.

AttachingTheSeat

1. Remove the two knobs from the bottom of seat.

2. Position the shoulder screws (found on the base of

the seat) inside the slot openings in the seat pivot

bracket.

3. Slide the seat slightly rearward in the seat pivot

bracket, lining up the rear slots in the pivot bracket

with the remaining two holes in the seat's base.

4. Select desired position for the seat, and secure with

the two knobs removed earlier. See Figure 3.

....... Screws

Figure 3

ShippingBraceRemoval

_. WARNING: Make sure the riding mower's

engine is off, set the parking brake and

remove the ignition key before removing the

shipping brace.

Locate the shipping brace, if present, and warning

tag found on the right side of the cutting deck. See

Figure 4.

While holding the discharge chute with your left

hand, remove the shipping brace with your right

hand by grasping it between your thumb and index

finger and rotating it clockwise.

Figure 4

WARNING: The shipping brace, used for

packaging purposes only, must be removed

and discarded before operating your riding

mower.

WARNING: The mowing deck is capable of

throwing objects. Failure to operate the riding

mower without the discharge cover in the

proper operating position could result in

serious personal injury and/or property

damage.

SettingtheGaugeWheels

ToolsRequired

(2) 9/16" wrenches

Select the height position of the cutting deck by placing

the deck lift lever in any of the six different cutting height

notches on the right fender.

Adjust the deck wheels so that they are between l_-inch

and _/2-inchabove the ground as follows.

WARNING: Keep hands and feet away

from the discharge opening of the cutting

deck.

Place the tractor on a firm and level surface, preferably

pavement, refer to Figure 5, and proceed as follows:

• Place the tractor's deck lift handle in the normally

desired mowing height setting, then check the

gauge wheels for contact or excessive clearance

with the surface below. There should be

approximately 1/2" clearance.

• If the wheels contact the surface adjust as follows:

a. Raise the deck lift handle to its highest

setting.

b. Remove the rear gauge wheels by removing

the lock nuts and shoulder screws which

secure them to the deck.

c. Place the deck lift handle in the desired

mowing height setting.

d. Insert the shoulder screw with the rear gauge

wheel into the index hole that leaves

approximately 1/2" between the bottom of the

wheel and the pavement. See Figure 5.

LockNut

GaugeWheel 1

ShoulderScrew

Figure 5

e. Notethe position of the index hole used; then

install the other rear gauge wheel into the

corresponding index hole of the other gauge

wheel brackets.

• If the gauge wheels have excessive clearance with

the surface below, lower the wheels to the index

hole that provides the approximate 1/2" clearance

as described above.

Refer to Levelingthe Beckon page 19 of this manual for

more detailed instructions regarding various deck

adjustments.

GasandOilFill-up

WARNING: Use extreme care when

handling gasoline. Gasoline is extremely

flammable and the vapors are explosive.

Never fuel machine indoors or while the

engine is hot or running. Extinguish

cigarettes, cigars, pipes, and other sources of

ignition before filling the fuel tank.

Use only clean, fresh (under 30 days old), unleaded

gasoline. Fill tank to no more than 1/2 inch below the

top of the filler neck to allow space for fuel expansion.

See Figure 6.

Filler Neck

FuelTank

Figure 6

IMPORTANT:You tractor is shipped with oil in the

engine. However, you MUST check the oil level before

operating. Refer to CheckingtheOilLevelon page 21 for

detailed instructions.

SECTION5: KNOWYOURLAWNTRACTOR

A. /

NOTE: Steering Wheel not shown for clarity,

Figure 7

A Systems Indicator Monitor/Hour Meter

B PTO (Blade Engage) Lever

C Parking Brake Lever

D Cruise Control Lever

E Shift Lever

F Cup Holder

Throttle Choke Control

Ignition Switch Module

Brake Pedal

Drive Pedal

Deck Lift Lever

NOTE: Any reference in this manual to the RIGHT or LEFT side of the tractor is observed from operator's position.

Throttle/ChokeControl

The throttle/choke control is

located on the right side of the

tractor's dash panel. This lever

controls the speed of the engine

and, when pushed all the way

forward, closes the choke for cold

starting. When set in a given

position, the throttle will maintain

a uniform engine speed.

IMPORTANT:When operating the

tractor with the cutting deck

engaged, be certain that the

throttle/choke control is always

in the FAST (rabbit) position.

BrakePedal

The brake pedal is located on the

right front side of the tractor

above the drive pedal along the

running board. The brake pedal

can be used for sudden stops or

setting the parking brake.

NOTE: The brake pedal must

be fully depressed to activate the

safety interlock switch when

starting the tractor.

ShiftLever

The shift lever is located on the

left side of the fender and has

three positions, FORWARD,

NEUTRAL and REVERSE. The

brake pedal must be depressed

and the tractor must not be in

motion when the moving shift

lever.

IMPORTANT:Never force the shift

lever. Doing so may result in

serious damage to the tractor's

transmission.

DeckLiftLever

Found on your tractor's right

fender, the deck lift lever is used

to change the height of the

cutting deck. To use, move the

lever to the left, then place inthe

notch best suited for your

application.

Oh0ke

Position

(o)

IgnitionSwitchModule

WARNING: Never leave a running machine

unattended. Always disengage the PTO,

move the shift lever into Neutral, set the

parking brake, stop the engine and remove

the key to prevent unintended starting.

To start the engine, insert the key into the ignition

switch and turn clockwise to the START position.

Release the key into the NORMAL MOWING MODE

position once the engine has fired.

To stop the engine, turn the ignition key

counterclockwise to the STOP position. See Figure 8.

Stop

Position Normal

- Mowing Mode

Start

Position

Figure 8

IMPORTANT:Prior to operating the tractor, refer to Safety

InterlockSystemon page 16 and ReverseCautionModeon

page 16 of this manual for detailed instructions

regarding the Ignition Switch Module and operating the

tractor in REVERSE CAUTION MODE.

DrivePedal /z

The drive pedal is located below //_

the brake pedal on the right front %_/

side of the tractor along the

running board. Depress the drive

pedal with your right foot when

the tractor shift lever is in either

FORWARD or REVERSE to

cause the tractor to move.

Ground speed is also controlled

with the drive pedal. The further

down the pedal is depressed, the faster the tractor will

travel. The pedal will return to its original position when

released.

SystemsIndicatorMonitor/HourMeter PTO(BladeEngage)Lever

Battery

42.0

PTO

(BladeEngage) ParkingBrake

LCD

Located in the center of the tractor's console, the

systems indicator monitor records, and displays on its

LCD, hours of tractor operation whenever the ignition

key is rotated out of the STOP position.

The Indicator Monitor will also remind the operator of

maintenance intervals for changing the engine oil. The

LCD will alternately flash the recorded hours, "CHG"

and "OIL" for five minutes, after every 50 hours of

recorded operation elapse. The maintenance interval

lasts for two hours (from 50-52, 100-102, 150-152,

etc.). The LCD will also flash as described above for

five minutes every time the tractor's engine has been

started during this maintenance interval. Before the

interval expires, change the crankcase oil as instructed

on page 22 of this manual.

Brake

If the Brake light illuminates when attempting to start

the tractor's engine, depress the brake pedal.

PT0 (Blade Engage)

If the PTO light illuminates when attempting to start the

tractor's engine, move the PTO lever into the

disengaged (OFF) position.

Battery

It is normal for the Battery light to illuminate while the

engine is cranking during start-up, but if it illuminate's

during operation, while the engine is running, the

battery is in need of a charge or the engine's charging

system is not generating sufficient amperage. Refer to

the MAINTAININGYOURLAWNTRACTORsection of this

manual for the proper battery charging procedure or

have the charging system checked by an authorized

Toro service dealer.

o.1'

OFF

PTO /BLADE

PTO

ENGAGE

The PTO (Blade Engage) lever is located on the left

side of the dash, next to the steering wheel. Move the

PTO (Blade Engage) lever forward to engage the

power to the cutting deck or other (separately available)

attachments; move the PTO (Blade Engage) lever

rearward to disengage the power to the attachments.

NOTE: The PTO (Blade Engage) lever must be in the

disengaged (OFF) position when starting the engine.

CruiseControlLever

The cruise control lever is located on

the tractor dash panel, below the _i_l

steering wheel. Push the cruise

control lever downward while

traveling forward at a desired speed.

While holding the lever down, release

pressure from the drive pedal.

This will engage the cruise control

and allow the tractor to remain at that

speed without applying pressure to

the drive pedal. Depress the brake

pedal or the drive pedal to deactivate cruise control.

Refer to page 17 for detailed instructions regarding

cruise control.

NOTE: Cruise control cannot be engaged at the

tractor's fastest ground speed. If the operator should

attempt to do so, the tractor will automatically

decelerate to the fastest optimal mowing ground speed.

ParkingBrakeLever

To set the parking brake, fully

depress the brake pedal and push the

parking brake lever down. Hold the

lever down while taking your foot off

the brake pedal. Both the parking

lever and the brake pedal will then

stay depressed. To release the

parking brake, depress the brake

pedal slightly. The parking brake

lever will then return to its original

position.

IMPORTANT: Always set the parking brake when

leaving the tractor unattended.

SECTION6: OPERATINGYOURLAWNTRACTOR

SafetyInterlockSystem

This tractor is equipped with a safety interlock system

for the protection of the operator. Before each use,

check the safety interlock system for proper operation.

If the interlock system should ever malfunction, do not

operate the tractor. Contact an authorized Toro service

dealer.

• The safety interlock system prevents the engine

from cranking or starting unless the parking brake is

engaged, and the PTO (Blade Engage) lever is in

the disengaged (OFF) position. To check for proper

operation, move the PTO (Blade Engage) lever into

the engaged (ON) position and release the parking

brake. Attempts to start the tractor's engine should

fail.

• The engine will automatically shut off if the operator

leaves the seat before engaging the parking brake.

To check for proper operation, start the tractor's

engine, release the parking brake and momentarily

raise yourself from the seat. The engine should

stall.

• The engine will automatically shut off if the operator

leaves the tractor's seat with the PTO (Blade

Engage) lever in the engaged (ON) position,

regardless of whether the parking brake is

engaged. To check for proper operation, start the

tractor's engine, move the PTO (Blade Engage)

lever inthe engaged (ON) position and momentarily

raise yourself from the seat. The engine should

stall.

• With the ignition key in the NORMAL MOWING

position, the engine will automatically shut off if the

PTO (Blade Engage) lever is moved into the

engaged (ON) position with the shift lever in

Reverse. To check for proper operation, start the

tractor's engine with the ignition key in the

NORMAL MOWING position, move the PTO

(Blade Engage) lever in the engaged (ON) position,

and place the shift lever into REVERSE. The

engine should stall.

WARNING: Do not operate the tractor if the

interlock system is malfunctioning. This

system was designed for your safety and

protection.

ReverseCautionMode

The REVERSE CAUTION MODE position of the key

switch module allows the tractor to be operated in

reverse with the blades (PTO) engaged.

IMPORTANT: Mowing in reverse is not recommended.

WARNING: Use extreme caution while

operating the tractor in the REVERSE

CAUTION MODE. Always look down and

behind before and while backing. Do not

operate the tractor when children or others

are around. Stop the tractor immediately if

someone enters the area.

To use the REVERSE CAUTION MODE:

IMPORTANT:The operator MUST be seated in the

tractor seat.

1. Start the engine as previously instructed in this

Operator's Manual.

2. Turn the key from the NORMAL MOWING

(Green) position to the REVERSE CAUTION

MODE (White) position of the key switch module.

See Figure 9.

3. Depress the REVERSE PUSH BUTTON (Orange,

Triangular Button) at the top, right corner of the key

switch module. The red indicator light at the top, left

corner of the key switch module will be ON while

activated. See Figure 9.

4. Once activated (indicator light ON), the tractor can

be driven in reverse with the cutting blades (PTO)

engaged.

5. Always look down and behind before and while

backing to make sure no children are around.

6. After resuming forward motion, return the key to the

NORMAL MOWING position.

IMPORTANT: The REVERSE CAUTION MODE will

remain activated until:

a. The key is placed in either the NORMAL

MOWING position or STOP position.

b. The operator leaves the seat.

indicator

Light

Stop

Position

REVERSE PUSH

BUTTON

Reverse

PushButton

Reverse

CautionMode

Position

Start

Position

Figure 9

StartingtheEngine

_, WARNING: Do not operate the tractor if the

interlock system is malfunctioning. This

system was designed for your safety and

protection.

NOTE: Refer to the TRACTORSET-UPon page 10 of this

manual for Gasoline and Oil fill-up instructions.

1. Insert the tractor key into the ignition switch

module.

2. Place the PTO (Blade Engage) lever in the

disengaged (OFF) position.

3. Engage the tractor's parking brake.

4. Activate the choke control.

5. Turn the ignition key clockwise to the START

position. After the engine starts, release the key. It

will return to the NORMAL MOWING position.

IMPORTANT: Do NOT hold the key in the START

position for longer than ten seconds at a time. Doing so

may cause damage to your engine's electric starter.

6. After the engine starts, deactivate the choke

control.

NOTE: Do NOT leave the choke control on while

operating the tractor. Doing so will result in a "rich" fuel

mixture and cause the engine to run poorly.

Stoppingthe Engine

WARNING: If you strike a foreign object,

stop the engine and remove the ignition key.

Thoroughly inspect the machine for any

damage. Repair the damage before restarting

and operating

1. If the blades are engaged, place the PTO/Blade

Engage lever in the disengaged (OFF) position.

2. Position the throttle/choke control between half-

throttle and the FAST (rabbit) position

3. Turn the ignition key counterclockwise to the STOP

position.

4. Remove the key from the ignition switch to prevent

unintended starting.

1. Depress the brake pedal to release the parking

brake and let the pedal up.

2. Move the throttle/choke control into the FAST

(rabbit) position.

IMPORTANT: Do NOT use the shift lever to change the

direction of travel when the tractor is in motion. Always

use the brake pedal to bring the tractor to a complete

stop before shifting.

3. To move forward, place the shift lever in the

FORWARD position, then slowly depress the drive

pedal until the desired speed is achieved.

4. To move in reverse, place the shift lever in the

REVERSE position, check that the area behind is

clear then slowly depress the drive pedal.

DrivingOnSlopes

Refer to the SLOPEGAUGEon page 9 to help determine

slopes where you may operate the tractor safely.

_, ARNING: Do not mow on inclines with a

slope in excess of 15 degrees (a rise of

approximately 2-1/2 feet every 10 feet). The

tractor could overturn and cause serious

injury.

•Mow up and down slopes, NEVER across.

• Exercise extreme caution when changing direction

on slopes.

• Watch for holes, ruts, bumps, rocks, or other

hidden objects. Uneven terrain could overturn the

machine. Tall grass can hide obstacles.

• Avoid turns when driving on a slope. If a turn must

be made, turn down the slope. Turning up a slope

greatly increases the chance of a roll over.

• Avoid stopping when driving up a slope. If it is

necessary to stop while driving up a slope, start up

smoothly and carefully to reduce the possibility of

flipping the tractor over backward.

SettingTheCruiseControl

_, ARNING: Never engage cruise control

while traveling in Reverse.

DrivingTheTractor

WARNING: Avoid sudden starts, ex-

cessive speed and sudden stops.

WARNING: Do not leave the seat of the

tractor without first placing the PTO (Blade

Engage) lever in the disengaged (OFF)

position, depressing the brake pedal and

engaging the parking brake. If leaving the

tractor unattended, also turn the ignition key

off and remove the key.

1. Slowly depress the drive pedal until the desired

speed is achieved.

2. Lightly depress the cruise control lever.

3. While continuing to hold the cruise lever down, lift

your foot from the drive pedal (you should feel the

cruise latch engage).

4. Once engaged, the cruise control lever and the

drive pedal will lock in the "down" position, and the

tractor will maintain the same forward speed.

NOTE: Cruise control can not be set at the tractor's

fastest ground speed. If the operator should attempt to

do so, the tractor will automatically decelerate to the

fastest optimal mowing ground speed.

Disengage the cruise control using one of the following

methods:

• Depress the brake pedal to disengage the cruise

control and stop the tractor.

• Lightly depress the drive pedal.

To change to the reverse direction when operating with

cruise control, depress the brake pedal to disengage

the cruise control and bring the tractor to a complete

stop. Place the shift lever in the REVERSE position and

depress the drive pedal.

Usingthe DeckLiftLever

To raise the cutting deck, move the deck lift lever to the

left, then place it in the notch best suited for your

application.

Engagingthe ParkingBrake

To engage the parking brake:

1. Fully depress the brake pedal and hold it while

gently pushing the parking brake lever downward.

2. Hold the parking brake lever down while removing

your foot from the brake pedal.

3. Once engaged, the parking brake lever and the

brake pedal will lock in the "down" position.

To disengage the parking brake, slightly depress the

brake pedal.

NOTE: The parking brake must be engaged if the

operator leaves the seat with the engine running or the

engine will automatically shut off.

Engagingthe Blades

Engaging the PTO (Blade Engage) transfers power to

the cutting deck or other (separately available)

attachments. To engage the blades, proceed as

follows:

1. Move the throttle/choke control to the FAST (rabbit)

position.

2. Grasp the PTO (Blade Engage) lever and pivot it all

the way forward into the engaged (ON) position.

See Figure 10.

3. Keep the throttle/choke control in the FAST (rabbit)

position for the most efficient use of the cutting

deck or other (separately available) attachments

IMPORTANT: The engine will automatically shut off if the

PTO is engaged with the shift lever in position for

reverse travel and the ignition key in the NORMAL

MOWING position. Refer to SafetyInterlockSystemon

page 16.

PTO

Engaged_/

Disngaged

NOTE:Steeringwheelnot shownfor clarity.__

Figure 10

Mowing

WARNING: To help avoid blade contact or

a thrown object injury, keep bystanders,

helpers, children and pets at least 75 feet

from the machine while it is in operation. Stop

machine if anyone enters the area.

The following information will be helpful when using the

cutting deck with your tractor.

WARNING: Plan your mowing pattern to

avoid discharge of materials toward roads,

sidewalks, bystanders and the like. Also,

avoid discharging material against a wall or

obstruction which may cause discharged

material to ricochet back toward the operator.

• Do not mow at high ground speed, especially if a

mulch kit or grass collector is installed.

• For best results it is recommended that the first two

laps be cut with the discharge thrown towards the

center. After the first two laps, reverse the direction

to throw the discharge to the outside for the

balance of cutting. This will give a better

appearance to the lawn.

• Do not cut the grass too short. Short grass invites

weed growth and yellows quickly in dry weather.

• Mowing should always be done with the throttle

control in the FAST (rabbit) position.

• Under heavy conditions it may be necessary to go

over the cut area a second time to get a clean cut.

• Do NOT attempt to mow heavy brush and weeds

and extremely tall grass. Your tractor is designed to

mow lawns, NOT clear brush.

• Keep the blades sharp and replace the blades

when worn. Refer to CuttingBladeson page 26 of this

manual for proper blade sharpening instructions.

SECTION7: MAKINGADJUSTMENTS

_, ARNING: Never attempt to make any

adjustments while the engine is running,

SeatAdjustment

To adjust the position of the seat, loosen the two knobs

on the bottom of the seat. See Figure 11. Slide the seat

forward or rearward as desired. Retighten the two

knobs.

Figure 11

LevelingtheDeck

NOTE: Check the tractor's tire pressure before

performing any deck leveling adjustments. Refer to

Tires on page 26 for information regarding tire pressure.

FrontTo Rear

The front of the cutting deck is supported by a stabilizer

bar that can adjusted to level the deck from front to rear.

The front of the deck should be between 1/4-inch and

3/8-inch lower than the rear of the deck. Adjust if

necessary as follows:

1. With the tractor parked on a firm, level surface,

place the deck lift lever in the top notch (highest

position) and rotate the blade nearest the discharge

chute so that it is parallel with the tractor.

2. Measure the distance from the front of the blade tip

to the ground and the rear of the blade tip to the

ground.

3. The first measurement taken should be between

1/4" and 3/8" less than the second measurement.

4. Determine the approximate distance necessary for

proper adjustment and proceed, if necessary, to the

next step.

5. From the front of the tractor, loosen the outermost

hex lock nut on the end of the deck hanger rod. See

Figure 12.

6. Tighten the inner hex nut front against the front

hanger bracket to raise the front of the deck; loosen

the hex nut to lower the front of the deck. See

Figure 12.

Figure 12

Retighten the two lock nuts against the inner hex

nuts when proper adjustment is achieved.

Side te Side

If the cutting deck appears to be mowing unevenly, a

side to side adjustment can be performed. Adjust if

necessary as follows:

1. With the tractor parked on a firm, level surface,

place the deck lift lever in the top notch (highest

position) and rotate both blades so that they are

perpendicular with the tractor.

2. Measure the distance from the outside of the left

blade tip to the ground and the distance from the

outside of the right blade tip to the ground. Both

measurements taken should be equal. If they're

not, proceed to the next step.

3. Loosen, but do NOT remove, the hex bolt on the left

deck hanger bracket. See Figure 13.

..................................................................................................J"/

Figure 13

4. Balance the deck by using a wrench to turn the

adjustment gear (See Figure 13) up or down.

5. The deck is properly balanced when both blade tip

measurements taken earlier are equal.

6. Retighten the hex bolt on the left deck hanger

bracket when proper adjustment is achieved.

SteeringAdjustment

If the tractor turns tighter in one direction than the other,

or if the ball joints are being replaced due to damage or

wear, the steering drag links may need to be adjusted.

Adjust the drag links so that equal lengths are threaded

into the ball joint on the left side and the ball joint on the

right side:

1. Loosen the jam nut found on the drag link at the

rear of the ball joint. See Figure 14.

Figure 14

2. Remove the hex nut on the top of ball joint. See

Figure 14.

3. Thread the ball joint toward the jam nut to shorten

the drag link. Thread the ball joint away from the

jam nut to lengthen the drag link.

4. Replace hex nut and retighten the jam nut after

proper adjustment is achieved.

NOTE: Threading the ball joints too far onto the drag

links will cause the front tires to "toe-in" too far. Proper

toe-in is between 1/16" and 5/16".

Front tire toe-in can be measured as follows:

1. Place the steering wheel in position for straight

ahead travel.

2. In front of the axle, measure the distance

horizontally from the inside of the left rim to the

inside of the right rim. Note the distance.

3. Behind the axle, measure the distance horizontally

from the inside of the left rim to the inside of the

right rim. Note the distance.

4. The measurement taken in front of the axle should

be between 1/16" and 5/16" less than the

measurement taken behind the axle.

5. Adjust if necessary.

SECTION8: MAINTAININGYOURLAWNTRACTOR

NOTE: Refer to MaintenanceCharton page 30 for a

reference of recommended maintenance intervals.

WARNING: Before performing any

maintenance or repairs, disengage PTO, set

parking brake, stop engine and remove key to

prevent unintended starting.

Engine

Maintenance, repair, or replacement of the emission

control devices and systems, which are being done at

the customer's expense, may be performed by any

engine repair establishment or individual. Warranty

repairs must be performed by an authorized Toro

service dealer.

EngineOil Recommendations

Using the proper type and weight of engine oil is

extremely important, as is checking and changing oil

regularly. Failure to use the correct oil, or operating the

engine with dirty oil will result in premature engine wear

and failure.

EngineOilType

Use only a high quality detergent

oil of API (American Petroleum

Institute) service class SG, SH,

SJ or higher. Selection of engine

oil should be based on the lowest

anticipated temperatures prior to

the next scheduled oil change.

Refer to the Temperature /Oil Viscosity Chart.

Checkingthe OilLevel

It is important to check the oil level at least every four

hours of operation. Regular checking during the first 24

hours of operation is especially important. Check the oil

level before each use as follows:

1. Allow the engine a few minutes to rest after

operation. This will give the oil time to drain into the

crankcase sump and result in a more accurate

dipstick reading.

2. Clean the area around the oil fill cap/dipstick to

prevent debris from entering the crankcase. Refer

to Figure 14.

3. Remove the oil fill cap/dipstick by lifting it out of the

oil fill tube.

4. Wipe the dipstick clean before pushing it all the way

back into the oil fill tube. Withdraw the dipstick to

check the oil level. Refer to figure at right.

5. Always keep the oil level at or near the F mark on

the dipstick. If the oil is low, add oil of the proper

type up to the F mark. Always re-check the oil level

with the dipstick before adding more oil.

TEMPERATURE/OIL VISCOSITYCHART

oF -20 i 2:0 312 40 iO 8i 100--==

°C i30 -iO -1:0 0 1;0 2;0 3;0 40

TemperatureChange ExpectedBefore Next Oil Change

*Use of synthetic oHhaving 5W-20 or 5W-30 rating is acceptaNe,

up to 4°0 (40°F).

**Synthetic oils wHnprovide better starting in extreme condbenow

23% (=IO°F).

IMPORTANT: Never operate the engine with the oil level

below the L mark or above the F mark on the dipstick.

6. After checking the oil level (and adding oil, if

necessary), reinstall the oil fill cap/dipstick by

inserting it into the oil fill tube

AddingOil

If, after checking the oil level,

you find the dipstick reads L,

proceed as follows.

• Place the tractor on a

level surface and engage

the parking brake. Stop

the tractor engine and OperatingRange

remove the ignition key.

• Clean the area around

the oil fill cap and fill tube

to prevent debris from

entering the crankcase.

• Remove the oil fill cap/

dipstick from the oil fill

tube and SLOWLY pour oil into the oil fill tube. Do

NOT pour more than 6 oz. of oil at a time without

first stopping and re-checking the oil level.

• Fill the crankcase until the oil level reaches the full

(F) mark on the dipstick. See Figure above. Refer to

the oil viscosity chart earlier in this section for

information regarding the proper type of oil to add

to the crankcase.

IMPORTANT: The engine (with oil filter) has a capacity of

50.75 oz. (1.5 liters). Never overfill the engine

crankcase.

IMPORTANT:The engine may overheat and/or damage

may result if the oil level is below the L or over the F on

the dipstick.

• Reinstall the oil fill cap/dipstick securely onto the oil

fill tube.

IMPORTANT:The oil fill cap/dipstick must be installed

securely onto the tube at all times when the engine

is operating. Severe engine damage could result from

failure to do so.

Changingthe EngineOil

The engine oil and oil filter should be changed after

every 50 hours of operation.

WARNING: If the engine has been recently

run, the engine, muffler and surrounding

metal surfaces will be hot and can cause

burns to the skin. Allow the tractor to cool and

use caution when removing

IMPORTANT: The oil filter should be changed at every

oil change interval.

To complete an oil change, proceed as follows:

Braining the 0il

Run the engine for a few minutes to allow the oil in the

crankcase to warm up. Warm oil will flow more freely

and carry away more of the engine sediment which may

have settled at the bottom of the crankcase. Use care to

avoid burns from hot oil.

1. Pop open the protective cap on the end of the oil

drain valve to expose the drain port. See Figure 15

2. Remove the oil fill cap/dipstick from the oil fill tube.

3. Push the oil drain hose (packed with this manual)

onto the oil drain port. Route the opposite end of

the hose into an appropriate oil collection container

with a capacity great enough to collect the used oil

(the engine, with oil filter, has a capacity of 50.75

oz./1.5 liters).

4. Push the oil drain valve in slightly, then rotate

counterclockwise and pull outward to begin

draining oil.

5. After the oil has finished draining, push the oil drain

valve back in, rotate it clockwise to lock the valve

closed and re-cap the end of the oil drain valve to

keep debris from entering the drain port.

IMPORTANT: Always change the oil filter when

performing an oil change on your tractor's engine.

Changing the 0il Filter

After draining the oil, proceed as follows:

1. Before removing the old oil filter, clean around its

base to prevent debris from entering the crankcase.

2. Grasp the oil filter and remove it from the filter

adapter by turning it counterclockwise.

3. Place a new replacement filter in a shallow pan with

the open end up and pour new oil of the proper type

(refer to the chart on page 21), in through the

threaded center hole.

_\ Oil Filter

Drain Port OilDrain Hose

Figure 15

IMPORTANT: Stop pouring when the oil reaches the

bottom of the threads and allow a minute or two for the

oil to be absorbed by the filter material.

4. Put a drop of oil on your fingertip and apply a light

coating to the gasket of the new oil filter.

5. Install the replacement oil filter on the engine by

turning it clockwise onto the filter adapter until the

rubber gasket makes contact with the base.

Tighten the filter an additional 1/2 turn after the

gasket first makes contact.

Re-fillingthe Crankcase with Oil

IMPORTANT: Always check the level on the dipstick as

instructed on page 21 before adding more oil. Do NOT

overfill.

NOTE: For the proper oil type, refer to the chart on

page 21 of this manual

1. Clean the area around the oil fill tube to prevent

debris from entering the crankcase.

2. Slowly pour oil into the fill tube. Fill the crankcase

until the oil level reaches the full (F) mark on the

dipstick (Refer to Page 21).

3. Reinstall the oil fill cap/dipstick securely into the oil

fill tube.

IMPORTANT:The oil fill cap/dipstick must be installed

securely onto the tube at all times when the engine

is operating. Severe engine damage could result from

a failure to do so.

4. Start the tractor engine and allow it to run for thirty

seconds, then stop the engine and remove the

ignition key.

5. Check the oil level and add oil if necessary. Do not

overfill the engine crankcase.

6. Examine the area around the base of the oil fill

tube, the oil filter adapter, and the oil drain valve for

leaks before operating the tractor.

IMPORTANT: If leaks are present, have your engine

serviced by an authorized Toro service dealer before

operating the tractor.

AirFilter

The engine is equipped with a replaceable, high density

paper air cleaner element. Always examine the air

cleaner before starting the engine. Check for a

buildup of dirt and debris around the air cleaner system.

Keep this area clean. Also check for loose or damaged

components. Replace all bent or damaged air cleaner

components.

NOTE: Starting the tractor with loose or damaged air

cleaner components could allow unfiltered air into the

engine causing premature wear and failure.

Service Paper Element

The paper element should be replaced at least once a

season, or every 100 hours of operation. Replace

more frequently if the tractor is operated under

extremely dusty conditions. To replace the paper

element, proceed as follows:

1. Loosen the air cleaner cover knob and remove the

cover. See Figure 16.

/ /

Figure 16

Remove the air cleaner element.

Remove the precleaner from the element and

service as instructed earlier in this section.

IMPORTANT: Do not wash the paper element or use

pressurized air, as this will damage the element.

Examine the element and discard if dirt and/or damage

is present.

NOTE: Handle new element carefully; do not use ff

the sealing surfaces are bent or damaged.

4. If any loose dirt or debris fell on the air cleaner base

when the element was removed, carefully remove it

and wipe the base clean. Be careful that none of it

drops into the intake.

5. Check the air cleaner base. Make sure it is secured

and not damaged. Also check the air cleaner cover

for damage or improper fit. Replace all damaged air

cleaner components.

6. Install the precleaner over the new paper element

and reinstall the element.

7. Reinstall the cover and tighten the knobs securely.

SparkPlug

Every two years or 200 hours of operation, remove the

spark plug, check its condition, and reset the gap or

replace with a new plug as necessary. Spark plug

replacement is recommended at 500 hours.

1. Lift the tractor's hood by pivoting it forward.

NOTE: Removing the tractor's hood may ease the

following steps, but is not necessary.

2. Remove the upper hex screws that secure the heat

shield in place, on both the left side and right side of

the tractor. See Figure 17.

NOTE:Hoodnot shownfor clarity.

Hex Screw

HeatShield

Figure 17

3. Pivot the heat shield forward.

4. Carefully pull the spark plug wire boot off of the

spark plug.

5. Before removing the spark plug, clean the area

around the base of the plug to keep dirt and debris

out of the engine.

6. Using a ratchet with a 5/8-inch spark plug socket,

remove the spark plug and check its condition.

7. Replace the plug if worn, dirty or damaged. Reuse

only after resetting the gap as instructed.

NOTE: Do not clean the spark plug using an abrasive

grit. Some grit could remain in the spark plug and enter

the engine causing extensive wear and damage.

,Check the gap using a feeler gauge and adjust, if

necessary, by carefully bending the ground

electrode. See Figure 18. Set the spark plug gap to

0.030 in (0.76 mm).

FeelerGauge

Spark Plug

Ground Electrode

Gap

Figure 18

9. Reinstall the spark plug into the cylinder head.

Torque the spark plug to 28132 ft. lb. (38.0/43.4

N.m).

10. Place the spark plug wire boot over the spark plug

and press until you feel it "click" in place.

FuelFilter

_, ARNING: Do not replace the fuel filter

when the engine is hot.

The engine is equipped with an inline fuel filter located

on the right side of the engine.

Visually inspect the filter periodically for a build-up of

residue inside the filter body, and for a dirty element

which can be indicated by discoloration. Replace the

fuel filter when dirty.

CleaningtheEngineAndDeck

Any fuel or oil spilled on the machine should be wiped

off promptly.

Do NOT allow debris to accumulate around the cooling

fins of the engine or on any other part of the machine,

especially the belts and pulleys.

DeskWashSystem

Your tractor's deck is equipped with a water port on its

surface as part of its deck wash system.

Use the deck wash system to rinse grass clippings from

the deck's underside and prevent the buildup of

corrosive chemicals. Complete the following steps

AFTER EACH MOWING:

1. Drive the tractor to a level, clear spot on your lawn,

near enough for your garden hose to reach.

IMPORTANT:Make certain the tractor's discharge chute

is directed AWAY from your house, garage, parked

cars, etc.

2. Disengage the PTO (Blade Engage), set the

parking brake and stop the engine.

3. Thread the hose coupler (packaged with your

tractor's Operator's Manual) onto the end of your

garden hose.

4. Attach the hose coupler to the water port on your

decks surface. See Figure 19.

Hose Coupler

Water Port

Figure 19

5. Turn the water on.

6. While sitting in the operator's position on the

tractor, start the engine and place the throttle lever

in the FAST (rabbit) position.

7. Move the tractor's PTO (Blade Engage) into the ON

position.

8. Remain in the operator's position with the cutting

deck engaged for a minimum of two minutes,

allowing the underside of the cutting deck to

thoroughly rinse.

9. Move the tractor's PTO (Blade Engage) into the

OFF position.

10. Turn the ignition key to the STOP position to turn

the tractor's engine off.

11. Turn the water off and detach the hose coupler

from the water port on your deck's surface..

Lubrication

WARNING: Before lubricating, repairing, or

inspecting, always disengage PTO, set

parking brake, stop engine and remove key to

prevent unintended starting.

Engine

Refer to Engineon page 21 for instruction regarding all

engine-related lubrication.

FrontWheels

Each of the front wheel axles and rims is equipped with

a grease fitting. See. Lubricate with 251H EP grease or

an equivalent No. 2 multi-purpose lithium grease after

every 25 hours of tractor operation.

RimGreaseFitting

Figure 20

PivotPoints& Linkage

Lubricate all the pivot points on the drive system,

parking brake and lift linkage at least once a season

with light oil.

SECTION9: SERVICE

Tires

WARNING: Never exceed the maximum

inflation pressure shown on the sidewall of the

tire.

The recommended operating tire pressure is

approximately 10 psi for the rear tires and 14 psi for the

front tires. Do not overinflate. Uneven tire pressure

could cause the cutting deck to mow unevenly.

Fuse

A 20 amp fuse is installed in your tractor's wiring

harness to protect the tractor's electrical system from

damage caused by excessive amperage.

If the electrical system does not function, or your

tractor's engine will not crank, first check to be certain

that the fuse has not blown. It can be found beneath the

seat, mounted to the inside of the frame, near the

battery tray.

IMPORTANT:Always use a 20 amp fuse for

replacement.

WARNING: Before servicing, repairing, or

inspecting, always disengage PTO, set

parking brake, stop engine and remove key to

prevent unintended starting.

CuttingBlades

WARNING: Be sure to shut the engine off,

and remove the ignition key to prevent

unintended starting before removing the

cutting blade(s) for sharpening or

replacement. Protect your hands by using

heavy gloves when grasping the blade.

_, ARNING: Periodically inspect the bladeadapter and/or spindle for cracks or damage,

especially if you strike a foreign object.

Replace immediately if damaged.

The blades may be removed as follows.

• Remove the deck from beneath the tractor, (refer to

CuttingDeckRemovalon page 27) then carefully flip

the deck over to expose its underside.

• Place a block of wood between the center deck

housing baffle and the cutting blade to act as a

stabilizer. See Figure 21.

• Remove the hex flange nut that secures the blade

to the spindle assembly. See Figure 21.

HexFlange Nut

Spindle Assembly

Figure 21

To properly sharpen the cutting blades, remove

equal amounts of metal from both ends of the

blades along the cutting edges, parallel to the

trailing edge, at a 25° to 30° angle.

Figure 22

IMPORTANT:If the cutting edge of the blade has already

been sharpened, or if any metal separation is present,

replace the blades with new ones.

It is important that each cutting blade edge be ground

equally to maintain proper blade balance. A poorly

balanced blade will cause excessive vibration and may

cause damage to the tractor and result in personal

injury.

IMPORTANT:When replacing the blade, be sure to

install the blade with the side of the blade marked

"Bottom" (or with a part number stamped in it) facing

the ground when the mower is in the operating position.

IMPORTANT:Use a torque wrench to tighten the blade

spindle hex flange nut to between 70 ft-lb (95 N.m) and

90 ft-lb (122 N.m).

Battery

California Proposition 65 Warning: Battery

posts, terminals, and related accessories

contain lead and lead compounds, chemicals

known to the State of California to cause

cancer and reproductive harm. Wash hands

after handling.

The battery is sealed and is maintenance-free. Acid

levels cannot be checked and fluid can not be added.

•Always keep the battery cables and terminals clean

and free of corrosive build-up.

• After cleaning the battery and terminals, apply a

light coat of petroleum jelly or grease to both

terminals

• Always keep the rubber boot positioned over the

positive terminal to prevent shorting.

IMPORTANT: If removing the battery, disconnect the

NEGATIVE (Black) wire from its terminal first, followed

by the POSITIVE (Red) wire. When re-installing the

battery, always connect the POSITIVE (Red) wire to the

POSITIVE (+) terminal before connecting the

NEGATIVE (Black) wire to the NEGATIVE (-) terminal.

Be certain that the wires are connected to the correct

terminals; reversing them could change the polarity and

cause damage to your engine's alternator.

Jump Starting

WARNING: Never jump start a damaged or

frozen battery (a battery can be identified as

frozen if its sides are bulged out, it's frosty and

it feels very solid). Be certain the vehicles do

not touch, and ignitions are off. Do not allow

cable clamps to touch.

1. Connect positive (+) cable to positive post (+) of

your tractor's discharged battery.

2. Connect the other end of the (+) cable to the

positive (+) post of the jumper battery.

3. Connect the second negative (-) cable to the

negative (-) post of the jumper battery.

4. Make the final connection on the engine block of

the stalled tractor, away from the battery. Attach to

a unpainted part to assure a good connection.

IMPORTANT: If the jumper battery is installed on a

vehicle (i.e. car, truck), do NOT start the vehicle's

engine when jump starting your tractor.

5. Start the tractor (as instructed on page 17).

6. Set the tractor's parking brake before removing the

jumper cables, in reverse order of connection.

7. Allow the tractor's engine to run for 15 minutes

before shutting it off to allow the alternator time to

charge the discharged battery.

Charging

WARNING: Batteries give off an explosive

gas while charging. Charge the battery in a

well ventilated area and keep away from an

open flame or pilot light as on a water heater,

space heater, furnace, clothes dryer or other

gas appliances.

IMPORTANT: When charging your tractor's battery, use

only a charger designed for 12V lead-acid batteries.

Read your battery charger's Owner's Manual prior to

charging your tractor's battery. Always follow its

instructions and heed its warnings.

If your tractor has not been put into use for an extended

period of time, charge the battery as follows:

1. Set your battery charger to deliver a maximum of

10 amperes.

2. If your battery charger is automatic, charge the

battery until the charger indicates that charging is

complete. If the charger is not automatic, charge for

no fewer than eight hours.

CuttingDeckRemoval

To remove the cutting deck, proceed as follows:

1. Place the PTO/Blade Engage lever in the

disengaged (OFF) position and engage the parking

brake.

2. Lower the deck by moving the deck lift lever into the

bottom notch on the right fender.

3. Remove the hairpin clip that secures the PTO cable

to the rear of the cutting deck. See Figure 23.

HairpinClip

Figure 23

4. Remove the PTO cable and accompanying spring

from the cutting deck.

5. Remove the deck belt from around the tractor's

engine pulley.

6. Looking at the cutting deck from the left side of the

tractor, locate the deck support pin on the rear left

side of the deck.

7. Pull the deck support pin outward to release the

deck from the deck lift arm. See Figure 24.

Figure 24

8. Repeat the above steps on the tractor's right side.

9. Move the deck lift lever into the top notch to raise

the deck lift arms up and out of the way.

10. Gently slide the cutting deck toward the front of the

tractor allowing the hooks on the deck to release

themselves from the deck stabilizer rod.

11. Gently slide the cutting deck (from the right side)

out from underneath the tractor.

ChangingtheDeckBelt

WARNING: Be sure to shut the engine off,

engage the parking brake and remove the

ignition key to prevent unintended starting

before removing the belt.

WARNING: Avoid the possibility of a

pinching injury. Do not place your fingers on

the idler spring or between the belt and a

pulley while removing the belt.

All belts on your tractor are subject to wear and should

be replaced if any signs of wear are present.

IMPORTANT:The V-belts found on your tractor are

specially designed to engage and disengage safely. A

substitute (non-OEM) V-belt can be dangerous by not

disengaging completely. For a proper working machine,

use factory approved belts.

To change or replace the deck belt on your tractor,

proceed as follows:

1. Remove the cutting deck.

2. Remove the belt covers by removing the screws

that fasten them to the deck. Refer to the figure

below.

3. Loosen, but do not remove the deck idler pulleys.

4. Remove the deck belt from around all pulleys,

including the deck idler pulleys.

5. Route the new belt as shown in the figure below

and retighten the deck idler pulleys.

6. Reinstall the belt guards removed earlier and

remount the deck to the tractor.

LX425

BeltCover

Idler Pulleys

SECTION10: OFF-SEASONSTORAGE

Clean and lubricate the tractor as instructed in Section7:

MAINTAININGYOURLAWNTRACTORon page 21 of this

manual before storing for an extended period.

Engine

If the engine will be out of service for two months or

more, use the following storage procedure:

1. Clean the exterior surfaces of the engine.

2. Change the oil and filter while the engine is still

warm from operation. Refer to ChangingEngineOilon

page 22.

3. The fuel system must be completely emptied, or the

gasoline must be treated with a fuel stabilizer such

as STA-BIL®to prevent deterioration. If you choose

to use a stabilizer, follow the manufacturers

recommendations, and add the correct amount for

the capacity of the fuel system. Fill the fuel tank

with clean, fresh gasoline. Run the engine for 2-3

minutes to get stabilized fuel into the carburetor.

To empty the system, run the engine until the tank

and system are empty.

WARNING: Drain fuel only into an

approved container outdoors, away from an

open flame. Allow engine to cool. Extinguish

cigarettes, cigars, pipes, and other sources of

ignition prior to draining fuel.

1. Remove the spark plug. Add one tablespoon of

engine oil into the spark plug hole. Install the plug,

but do not reconnect the plug wire. Crank the

engine two or three revolutions.

2. Store the engine in a clean, dry place.

WARNING: Never store the machine or

fuel container indoors where there is an open

flame, spark or pilot light such as on water

heater, furnace, clothes dryer or other gas

appliance.

SECTION11: MAINTENANCECHART

Before

Each Use Every

10 Hours Every

25 Hours Every

50 Hours Every

200 Hours Every

Season

Prior

to Storing

Check Safety

Interlock System J

Clean Hood/Dash Louvers ,_ _'

Check Engine Oil Level _'

Replace Air Filter Element ,_

Change Engine Oil & Filter _' _'

Clean Battery Terminals _' _'

Lube Front Axles and Rims _' ,_

Clean Engine Cooling Fins _' _'

Lube Pedal Pivot Points _' _'

Check Spark Plug ,_' _'

Service Air Filter Element J

SECTION12: TROUBLESHOOTING

Trouble

Engine fails to start

Engine runs erratic

Possible Cause(s)

PTO (Blade Engage) lever engaged.

Parking brake not engaged.

Spark plug wire disconnected.

Throttle/choke control not in correct

starting position.

Choke not activated

Fuel tank empty, or stale fuel.

Blocked fuel line.

Faulty spark plug.

Engine flooded.

Unit running with CHOKE activated.

Spark plug wire(s) loose.

Blocked fuel line or stale fuel.

Vent in gas cap plugged.

Water or dirt in fuel system.

Dirty air cleaner.

Engine overheats Engine oil level low.

Air flow restricted.

Engine hesitates at high RPM

Idles poorly

Excessive vibration

Mower will not mulch grass

Spark plug gap too close.

Spark plug fouled, faulty or gap too

wide.

Dirty air cleaner.

Cutting blade loose or unbalanced.

Damaged or bent cutting blade.

Engine speed too low.

Wet grass.

Excessively high grass.

Dull blade.

Uneven cut Deck not balanced properly.

Dull blade.

Uneven tire pressure.

Corrective Action

Place PTO (Blade Engage) lever in (OFF) position.

Engage parking brake.

Connect wire to spark plug.

Move Throttle/Choke Control into CHOKE position.

Fill tank with clean, fresh (less than 30 days old) gas.

Clean fuel line or replace fuel filter.

Clean, adjust gap or replace plug.

Crank engine with throttle in FAST position.

Move Throttle/Choke Control out of CHOKE position.

Connect and tighten spark plug wire(s).

Clean fuel line; fill tank with clean, fresh (less than 30

days old) gasoline. Replace fuel filter, if so equipped.

Clear vent or replace cap if damaged.

Drain fuel tank. Refill with clean, fresh (less than 30

days old) gasoline.

Replace air cleaner paper element or clean foam

precleaner.

Fill crankcase with proper capacity and weight of oil.

Clean grass clippings and debris from around the

engine's cooling fins and blower housing.

Remove spark plug and reset the gap.

Replace spark plug. Set plug gap.

Replace air cleaner element or clean pre-cleaner.

Tighten blade and spindle. Balance blade.

Replace blade.

Place throttle in FAST (rabbit) position.

Do not mow when grass is wet; wait until later to cut.

Mow once at a high cutting height, then mow again at

desired height or make a narrower cutting swath.

Sharpen or replace blade.

Perform side-to-side deck adjustment.

Sharpen or replace blade.

Check tire pressure in all four tires.

SECTION13: SPECIFICATIONS*

LX425

Capacities

Fuel Tank

Engine Crankcase (w/filter)

Variable Speed Transmission

Forward Speed

Reverse Speed

Engine (Air-cooled, 4-cycle)

Make Kohler Courage

Model SV600

Cylinders Single

Bore 3.70 in. (94 mm)

Stroke 3.38 in. (86 mm)

Displacement 36.4 cubic in. (597 cc)

Power @3600 RPM 20 HP (14.9 kW)**

Maximum Torque 36.9 ft. lb. (50.0 Nm)

@ 2200 RPM

Compression Ratio 8.5:1

Engine Speed (governed) 3375 RPM

Low Speed 2150 RPM (_+75 RPM)

Spark Plug Gap .030 in. (.76 mm)

Electrical System

System Voltage 12-volt Negative Ground

Battery 190 CCA (sealed)

Alternator 15 Amp Regulated

Fuse (automotive type) 20 Amp

Headlights Incandescent

Brakes Single Disc (Dry)

Turf Tires

Front (inches) 15 x 6 x 6

Rear (inches) 20 x 8 x 8

Dimensions

Cutting Width, Deck 42 in. (106.7 cm)

Wheelbase 46 in. (116.8 cm)

Length, over all 68 in. (172.7 cm)

Width, over all 45 in. (114.3 cm)

Height, over all 43 in. (109.2 cm)

Ground Clearance 4.5 in. (11.4 cm)

Turning Radius 18 in. (46 cm)

Weight (approximate) 498 lb. (225.9 kg)

3.0 gal. (11.4 liters)

50.75 oz. (1.5 liters)

O- 5.2 mph (8.2 km/h)

O- 2.3 mph (3.7 km/h)

*Toro reserves the right to change product specifications, design, and standard equipment without notice and without incurring obligation

** Kohler's horsepower ratings exceed Society of Automotive Engineers Small Engine Test Code J1940. Actual engine horsepower is lower and

affected by, but not limited to, accessories (air cleaner, exhaust, charging, cooling, fuel pump, etc.), application, engine speed and ambient

operating conditions (temperature, humidity, and altitude).

ELECTRICSCHEMATIC

_ltl,

n--+

I_+

D+

rrrn

3++

CC_OJ

L+

OCO

CALiFORNiAEMiSSiONCONTROLWARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND OBLiGATiONS

The CaliforniaAir ResourcesBoardandMTDConsumerGroupInc are pleasedto explainthe evaporativeemissioncontrolsystemwarrantyonyour 2007 lawn

mower.In California,new lawnmowermustbe designed,builtand equippedto meetthe State'sstringentanti-smogstandards.MTDConsumerGroupInc must

warrantthe EECSon your lawnmowerfor the periodof timelisted below providedthere has been noabuse,neglector impropermaintenanceof your lawnmower.

YourEECSmayincludeparts suchasthe carburetor,fuel-injectionsystem,the ignitionsystem,catalyticconverter,fueltanks,fuel lines,fuelcaps,valves,

canisters,filters,vaporhoses,clamps,connectors,and otherassociatedemission-relatedcomponents.

Where a warrantable condition exists, MTDConsumer Group Inc will repair your lawn mower at no cost toyou includingdiagnosis, partsand labor.

MANUFACTURER'S WARRANTY COVERAGE:

Thisevaporativeemissioncontrolsystemis warrantedfor two years. If anyevaporativeemission-relatedparton your equipmentis defective,the partwill be

repairedor replacedby MTDConsumerGroupInc.

OWNER'S WARRANTY RESPONSIBILITIES:

Asthe lawn mowerowner,you are responsiblefor performanceof the requiredmaintenancelistedin your owner'smanual. MTDConsumerGroupInc recom-

mendsthat youretainall receiptscoveringmaintenanceonyour lawnmower,but MTDConsumerGroupInccannotdenywarrantysolelyfor the lackof receipts.

Asthe lawn mowerowner,youshouldhoweverbeawarethat MTDConsumerGroupInc maydeny youwarrantycoverageifyour lawnmoweror a part hasfailed

dueto abuse,neglect,or impropermaintenanceor unapprovedmodifications.

Youare responsiblefor presentingyour lawnmowerto MTDConsumerGroupInc'sdistributioncenteror servicecenteras soon asthe problemexists.The

warrantyrepairsshouldbe completedin a reasonableamountof time,notto exceed30 days.If you havea questionregardingyour warrantycoverage,you should

contactthe MTDConsumerGroup IncService Departmentat 1-800-800-7310.

GENERAL EMISSIONS WARRANTY COVERAGE:

MTDConsumerGroupIncwarrantsto the ultimatepurchaserand eachsubsequentpurchaserthat the lawnmoweris:Designed,builtand equippedso asto

conformwith allapplicableregulations;andfree fromdefectsin materialsand workmanshipthatcausethe failureofa warrantedpartto beidenticalin all material

respectsto that part as describedin MTDConsumerGroupInc'sapplicationfor certification.

Thewarrantyperiodbeginsonthe datethe lawn moweris deliveredto anultimatepurchaserorfirst placedintoservice.The warrantyperiodis two years.

Subjectto certainconditionsand exclusionsas statedbelow,the warrantyon emission-relatedparts isas follows:

1. Any warrantedpart that isnot scheduledfor replacementas requiredmaintenanceinthe writteninstructionssupplied,is warrantedfor thewarranty period

statedabove. If the partfails duringthe periodof warrantycoverage,the part will be repairedor replacedby MTDConsumerGroupInc accordingto subsection

(4) below.Anysuch part repairedor replacedunderwarrantywillbe warrantedfor the remainderofthe period.

2. Any warrantedpart that is scheduledonly for regularinspectioninthe written instructionssuppliedis warrantedfor thewarranty periodstated above.Any such

partrepairedor replacedunderwarrantywill bewarrantedfor the remainingwarrantyperiod.

3. Any warrantedpart that isscheduledfor replacementas requiredmaintenancein the writteninstructionssuppliedis warrantedfor the periodof timebeforethe

firstscheduledreplacementdatefor that part.If the part fails beforethe firstscheduledreplacement,the partwill berepairedor replacedby MTDConsumer

GroupInc accordingto subsection(4) below.Any suchpart repairedor replacedunderwarrantywill be warrantedforthe remainderof the periodprior to the

firstscheduledreplacementpointfor the part.

4. Repairor replacementof any warrantedpart underthe warrantyprovisionshereinmust be performedat a warrantystationat nochargeto the owner.

5. Notwithstandingthe provisionsherein,warrantyservicesor repairswill be providedat all of our distributioncentersthat arefranchisedto servicethe subject

enginesor equipment.

6. The lawnmowerownerwill not bechargedfor diagnosticlaborthat isdirectlyassociatedwith diagnosisof a defectke,emission-relatedwarrantedpart,

providedthatsuch diagnosticwork isperformedat a warrantystation.

7. MTDConsumerGroupInc is liablefor damagesto otherengine orequipmentcomponentsproximatelycausedby a failure underwarrantyof any warranted

part.

8. Throughoutthe lawnmowerwarranty periodstated above,MTDConsumerGroupInc willmaintaina supplyof warrantedparts sufficientto meet theexpected

demandfor suchparts.

9. Any replacementpartmay beusedinthe performanceof any warrantymaintenanceor repairsand mustbe providedwithoutchargeto the owner.Suchusewill

not reducethe warrantyobligationsof MTDConsumerGroupInc.

10.Add-onor modifiedpartsthat are notexemptedby theAir ResourcesBoard maynotbe used.The useof anynon-exemptedadd-onor modifiedparts bythe

ultimatepurchaserwillbe groundsfor disallowinga warrantyclaims. MTDConsumerGroupIncwill not beliableto warrantfailuresof warrantedparts caused

bythe use of a non-exemptedadd-onor modifiedpart.

WARRANTED PARTS:

Therepairor replacementof anywarrantedpart otherwiseeligiblefor warrantycoveragemaybeexcludedfromsuch warrantycoverageif MTDConsumerGroup

Inc demonstratesthat the lawnmowerhas beenabused,neglected,orimproperlymaintained,andthat suchabuse,neglect,or impropermaintenancewasthe

directcauseof the need for repairor replacementof the part.That notwithstanding,anyadjustmentof a componentthat has afactory installed,and properly

operating,adjustmentlimitingdevice isstill eligiblefor warrantycoverage.Thefollowingemissionwarrantyparts list arecovered: FuelLine,Fuel LineClamps

The Toro Company

MANUFACTURER'S LIMITED WARRANTY FOR

LAWN & GARDEN TRACTORS

IMPORTANT: To obtain warrantycoverage owner must present an a.

original proof of purchase and applicable maintenance records to the

servicing dealer. Please see the operator's manual for information

on required maintenance and service intervals, b.

The limitedwarranty set forth below is given by The Toro Company

("Toro") and The Toro Warranty Company, pursuant to an

agreement between them, with respect to new merchandise

purchased or leased and used in the United States and/or its

territories and possessions, and by Toro with respect to new

merchandise purchased or leased and used in Canada and/or its

territories and possession.

Torowarrantsthis product(excludingits NormalWearPartsand

Batteriesas describedbelow)againstdefectsin materialand e.

workmanshipfor a periodof two (2)yearscommencingonthe

dateof original retailpurchaseor leaseandwill, at its option,repair f.

or replace,free of charge,any partfound to bedefectivein materials g.

orworkmanship.

Normal Wear Parts are warranted to be free from defects in material

and workmanship for a period of thirty (30) days from the date of

original purchase or lease. Normal wear parts include, but are not

limited to items such as: belts, blades, blade adapters, grass bags,

rider deck wheels, seats, and tires.

Batteries have a one-year prorated limitedwarranty against defects

in material and workmanship, with 100% replacement during the first

three months. After three months, the battery replacement credit is

based on the months remaining in the twelve (12) month period

dating back to the original date of original sale or lease. Any

replacement battery will be warranted only for the remainder of the

original warranty period.

This limitedwarranty shall only apply if this product has been

operated and maintained in accordance with the Operator's Manual

furnished with the product, and has not been subject to misuse,

abuse, commercial use, neglect, accident, improper maintenance,

alteration, vandalism, theft, fire, water, or damage because of other

peril or natural disaster. Damage resulting from the installation or

use of any part, accessory or attachment not approved by Toro for

use with the product(s) covered by this manual will void your

warranty as to any resulting damage. In addition, Toro may deny

warranty coverage if the hour meter, or any part thereof, is altered,

modified, disconnected or otherwise tampered with.

HOWTOOBTAINSERVICE:Warrantyserviceis available,WITH

PROOFOF PURCHASEANDAPPLICABLEMAINTAINCE

RECORDS,throughyourlocalauthorizedservicedealer.To locate

thedealerinyour areacheckyourYellowPages,or contact;

Customer Care Department,ConsumerDivision

ToroWarrantyCompany

8111LyndaleAvenueSouth

Bloomington,MN55420,1196

In the US1-888-384-9942(In Canada1-888-848-4073)

or logon to ourWeb siteat www.toro.com.

Withoutlimitingtheforegoing,this limitedwarrantydoes notprovide

coveragein thefollowingcases:

Theengineor componentpartsthereof. Theseitemsmay

carrya separatemanufacturer'swarranty. Referto

applicablemanufacturer'swarrantyfor termsandconditions.

Routinemaintenanceitemssuchas lubricants,filters, blade

sharpening,tune-ups,brakeadjustments,clutch

adjustments,deckadjustments,andnormaldeteriorationof

theexteriorfinishdue to use or exposure.

Servicecompletedby someoneotherthan an authorized

servicedealer.

Torodoes notextendanywarrantyfor productssold or

exportedoutsideof the UnitedStatesand/orCanada,and

their respectivepossessionsandterritories,exceptthose

sold throughToro'sauthorizedchannelsof export

distribution.

Replacementpartsand\oraccessoriesthatare not genuine

Toro parts.

Transportationchargesand servicecalls.

Torodoes notwarrantthis productfor commercialuse.

There are noimpliedwarranties,includingwithout

limitationany impliedwarrantyof merchantabilityor

fitness for a particularpurpose.Nowarrantiesshallapply

afterthe applicableperiodof expresswrittenwarranty

above.Nootherexpresswarrantiesbeyondthose

mentionedabove,givenby anypersonorentity,

includinga dealeror retailer,withrespectto any product,

shallbindToro. Theexclusiveremedyis repairor

replacementof the productas setforth above.Theterms

of thiswarrantyprovidethe soleandexclusiveremedy

arisingfrom the sale and/orleaseof the products

coveredhereby.Toroshallnotbe liablefor any incidental

or consequentiallossordamageincluding,without

limitation,expensesincurredfor substituteor

replacementlawncareservicesorfor rentalexpensesto

temporarilyreplacea warrantedproduct.

Somejurisdictionsdo notallowthe exclusionorlimitationof

incidentalor consequentialdamages,or limitationsonhowlongan

impliedwarrantylasts,so theabove exclusionsor limitationsmay

notapplyto you.

In no event shall recovery of any kind be greater than the amount of

the purchase price of the product sold. Alteration of safety

features of the product shall void this warranty. You assume the

risk and liability for loss, damage, or injury to you and your property

and/or to others and their property arising out of the misuse or

inability to use the product.

Thislimitedwarrantyshallnotextendto anyoneotherthan the

originalpurchaserorto thepersonforwhomit waspurchasedasa

gift.

HOWLOCAL LAWS RELATETOTHISWARRANTY:Thislimited

warrantygivesyouspecificlegalrights,and you mayalsohaveother

rightsthat varyin differentjurisdictions.

CustomerCareDepartmentof the Toro Warranty Company,8111LyndaleAve.South,

Bloomington,MN55420-1196or call(US)1-888-384-9942,(Canada)1-888-848-4073;www.toro.com

374-0100Rev. B

Toro 13BX60RG744 User Manual TRACTOR Manuals And Guides 1101331L

Navigation menu

Versions of this User Manual:

Views

Navigation