7106507028_Archer VR500v_QIG_V1 7106507028 Archer VR500v V1 Quick Installation Guide

2017-03-07

: Tp-Link 7106507028 Archer Vr500V V1 Quick Installation Guide 7106507028_Archer VR500v_V1_Quick Installation Guide

Open the PDF directly: View PDF PDF.
Page Count: 2

Quick Installation Guide
VR500v
AC1200 Wireless Dual Band Gigabit VoIP
VDSL/ADSL Modem Router
Connect the Hardware
Configure the Modem Router
Enjoy the Internet Now you can enjoy your internet.
http://tplinkmodem.net
HighMiddleLow
Let’s Get Started
Conrm Password
New Password
2. Connect your router to the internet.
Launch a web browser and type in http://tplinkmodem.net or
192.168.1.1.
Note: If the login page does not appear, please refer to FAQ->Q1.
A
C
BCreate a password (1-15 characters) and get started.
Follow the step-by-step instructions to set up an internet connection.
Wired Connection
Wireless Connection
Connect wirelessly by using the SSID (network name) and Wireless
Password printed on the product label at the bottom of the router.
1. Connect your computer to the router via a wired or wireless connection.
Power Adapter
Phone Cable
Phone (Optional)
2
If you don’t need a phone service, directly connect the modem router to the phone jack
with the provided phone cable, then follow steps 3 and 4 to complete the hardware
connection.
3Push in to turn on the
modem router.
Phone Cable
Phone Jack
1
DSL Splitter
LINE
PHONEMODEM
Note: The DSL LED takes 1 to 2 minutes
to stabilize.
Power On DSL On
4Verify that the following LEDs turn
stable before continuing with the
conguration.
Ethernet Cable
7106507028 REV1.0.0
©2016 TP-Link
Q1. What should I do if I cannot access the web management page?
A1. If the computer is set to a static IP address, change its settings to obtain an IP address
automatically.
A2. Make sure http://tplinkmodem.net or http://192.168.1.1 is correctly entered in the web
browser.
A3. Use another web browser and try again.
A4. Reboot your modem router and try again.
A5. Disable then enable the network adapter in use.
Q2. What should I do if the DSL LED does not turn solid on?
A1. Check your cables and make sure they are all plugged in correctly, including the
telephone lines and power adapter.
A2. Restore your modem router to its factory default settings.
A3. Remove the DSL splitter, directly connect the modem router to the phone jack and
follow this guide to reconfigure the modem router.
A4. Contact your ISP (internet service provider) to check the status of your DSL line.
A5. If the problem persists, contact our Technical Support.
Q3. What should I do if I cannot access the internet?
A1. Make sure all telephone and Ethernet cables are correctly and securely connected to the
modem router.
A2. Try to log in to the web management page of the modem router using the default address
at http://tplinkmodem.net or http://192.168.1.1. If you cannot, change your computer
settings to obtain an IP address automatically from the modem router. If you can, try the
steps below.
A3. Consult your ISP (internet service provider) and make sure that the VPI/VCI (or VLAN ID),
connection type, account username and password are all correct. If they are not, please
replace them with the correct settings and try again.
A4. Restore the modem router to its factory default settings and reconfigure it by following the
instructions in this guide.
A5. Please contact our Technical Support if the problem persists.
Q4. What should I do if I forget my password?
For the web management page:
A. Restore the modem router to its factory default settings and then set a new password
using 1-15 characters.
For the Wi-Fi network:
A1. The default Wi-Fi Password can be found on the product label at the bottom of the
modem router.
A2. If the default wireless password has been changed, log in to the web management
page and go to Basic > Wireless to retrieve or reset your password.
Q5. How do I restore the modem router to its factory default settings?
A1. With the modem router powered on,
press and hold the RESET button on the
rear panel of the modem router for
approximately 10 seconds until all LEDs
turn back on, then release the button.
A2. Log in to the web management page of the modem router. Go to Advanced > System
Tools > Backup & Restore and click Factory Restore. The modem router will restore
and reboot automatically.
FAQ (Frequently Asked Questions)
LED Indicators
Remote Access
via FTP Server
Local Storage
Sharing
Media Sharing
FeaturesMake Telephone Calls via Internet
Ethernet WAN Connection
Connect an Ethernet cable (RJ45) from your fiber or cable modem to the
WAN port of the modem router to use it as a wireless router. Refer to the
User Guide for wireless router configuration.
3G/4G Connectivity
Connect a 3G/4G USB mobile broadband modem to the router’s USB port
to get wireless internet access through 3G/4G mobile networks. The USB
dongle can be congured as the primary internet connection, or as a
backup to enhance network reliability. Refer to the User Guide for
instructions.
USB Features
The USB port can be used for le and media sharing, both locally over your
home network and remotely over the internet using the router's built-in FTP
server capability.
Press & Hold for 10 Seconds
1. Register the telephone number.
A Visit http://tplinkmodem.net, and log in with the password you have set.
B Go to Advanced > Telephony > Telephone Numbers to open the
configuration page. Click Add.
C Select Other from the dropdown list, enter the information provided by
your telephony service provider, and click Save to save the settings.
2. Connect your telephone to an RJ11 (Phone 1 or Phone 2) port on the
back panel. You can now make phone calls over the internet.
Telephone Numbers
Status Telephone Number Provider Modify
Authentication ID
Password
Registrar Address:
Phone Number:
Telephony Provider Other
--------
Cancel Save
Refresh Add Delete All
*
*
Advanced
USB Sharing Port
LED Status Indication
Power is on.
Power is off.
DSL synchronization is complete.
DSL synchronization is in progress.
DSL synchronization failed.
Internet connection is available.
No internet connection.
The 2.4GHz wireless radio band is enabled.
The router is transmitting or receiving data via 2.4GHz
band.
The 2.4GHz wireless radio band is disabled.
The 5GHz wireless radio band is enabled.
The router is transmitting or receiving data via 5GHz band.
The 5GHz wireless radio band is disabled.
Turns on when a WPS synchronization is established and
automatically turns off about five minutes later.
A wireless device is trying to connect to the network via
WPS. This process may take up to 2 minutes.
A device is connected to the WAN port.
The WAN port is sending or receiving data.
No device is connected to the WAN port.
A device is connected to the LAN port.
The LAN port is sending or receiving data.
No device is connected to the LAN port.
The phone is off-hook.
The phone is ringing.
The phone is on-hook.
The USB device is ready to use.
A new USB device is being identified, or data is being
transferred.
No USB device is plugged into the USB port.
On
O
On
Flashing
O
On
O
On
Flashing
O
On
Flashing
O
On/O
Flashing
On
Flashing
O
On
Flashing
O
On
Flashing
O
On
Flashing
O
Power
DSL
Internet
Wireless
2.4GHz
Wireless
5GHz
LAN
USB
WPS
Phone
WAN

Navigation menu