TransCore 05847 DIGITAL SPREAD SPECTRUM FHSS TRANSCEIVER User Manual

TransCore DIGITAL SPREAD SPECTRUM FHSS TRANSCEIVER

a href="https://usermanual.wiki/TransCore" itemprop="url"> TransCore >

User Manual

This document describes the procedures to set up and use an Encompass 1150 (E1150) Mobile Reader. Required SuppliesYou need the following additional materials and/or tools to complete the reader installation:•Host PC using Windows (2000, XP, Vista, or 7) operating system with CD drive and at least one USB port (either USB 1.0 or USB 2.0)•Field Configuration Software (FCSW) CDROM•USB communications cable provided with E1150•Battery charger with power cable provided with E1150•Test tag provided with E1150Installing Field Configuration Software (FCSW)Install the Field Configuration SoftwareInsert the FCSW CDROM into the host computer and follow the steps to load the software. The program installs a shortcut icon for the software and a shortcut icon for the E1150 mobile reader instructions to the desktop.CAUTION: Do not launch the field configuration software program at this time.E1150 SetupNote: The E1150 mobile reader is designed primarily for use in an office environment, but can be used outdoors in a limited environment.1. Place the E1150 on a flat surface.2. Plug the power cord from the E1150 battery charger into the Charger port at the base of the E1150. Plug the power cord into a standard 110V AC wall outlet. Allow the E1150 to fully charge. The green LED indicator located on the charger will illuminate when the unit is ready for use. The E1150 unit receives its charging via the dedicated charger connected through the Charger port. The unit cannot be charged through the USB port. Note: The automatic charger shutoff allows for the E1150 to remain connected to the charger after completion of a charge cycle.3. Connect the USB data cable from the USB port at the base of the E1150 to one of the host computer's USB ports. Allow the device driver to be detected and installed automatically. If the device driver fails to automatically load, disconnect the E1150 from the host computer. Locate the device driver setup executable file on the root directory of the field configuration software CDROM: CDM20828_Setup.exe, or go to http://www.ftdichip.com/Drivers/CDM/CDM20828_Setup.exe to download Encompass® 1150 Mobile Reader16-1150-002 REV A
2the driver from the FTDIchip website. Launch the CDM20828_Setup.exe file and allow it to automatically install the necessary device driver. Reconnect the E1150 and allow it to be detected by the operating system.Start the E1150 Field Configuration Software1. Launch the field configuration software via the desktop shortcut icon.2. The E1150 FCSW startup window will open (Figure 1). Click Connect. Click COM Port.Figure 1 E1150 Field Configuration Software Startup Window3. Select the associated COM port from the COMSelect window (Figure 2). Click CONNECT. Observe that the connect status in the lower left corner of the window reads Connected.Figure 2 COM Port Selection Window4. To view the FCSW and E1150 Version information, click on Help and then About (Figure 3).Note: The firmware version shown in Figure 3 is for example only. Your version information may be different.
Download:
Mirror Download [FCC.gov]
Document ID2300148
Application IDteiQlXv+261jlodWerqjGA==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize28.12kB (351453 bits)
Date Submitted2014-06-19 00:00:00
Date Available2014-06-19 00:00:00
Creation Date2014-05-27 10:15:35
Producing SoftwareiText 2.1.7 by 1T3XT
Document Lastmod2014-05-27 10:15:35
Document TitleUser Manual
Document Creatorpdfsam-console (Ver. 2.4.1e)
FCC ID Filing: FIH05847

Navigation menu