Trimline 29253 Users Manual DOM IB E 2

29253 to the manual 1ad980ae-2a5b-40cb-a0ae-fea1cfa57e0e

2015-02-03

: Trimline Trimline-29253-Users-Manual-460260 trimline-29253-users-manual-460260 trimline pdf

Open the PDF directly: View PDF PDF.
Page Count: 2

DownloadTrimline Trimline-29253-Users-Manual- 29253 DOM IB E 2  Trimline-29253-users-manual
Open PDF In BrowserView PDF
29253 Series
Trimline Phone
User's Guide

INTRODUCTION

TROUBLESHOOTING TIPS

Your telephone is designed to give you flexibility in use and high
quality performance. To get the most from your new telephone,
we suggest that you take a few minutes right now to read
through this instruction manual.

No dial tone.
• Press and release the hook switch. Check the hook switch: Does it fully extend
when the handset is lifted from the cradle?

CAUTION: When using telephone equipment, there are basic
safety instructions that should always be followed. Refer to the
IMPORTANT SAFETY INSTRUCTIONS provided with this
product and save them for future reference.
NOTE: This phone uses Touch-Tone dialing service only. For this
telephone to function properly, you must use Touch-Tone service
available through your local telephone company.

BEFORE YOU BEGIN
TELEPHONE JACK REQUIREMENTS

Wall plate

To use this phone, you need an RJ11C
type modular telephone jack, which might
look like the one pictured here, installed in
your home. If you don’t have a modular
jack, call your local phone company to
find out how to get one installed.

To keep your telephone working and looking good, follow these
guidelines:

IMPORTANT INSTALLATION INFORMATION

• Avoid putting the phone near heating appliances and devices that
generate electrical noise (for example, motors or fluorescent lamps).

• Never install telephone wiring during a lightning storm.

• DO NOT expose to direct sunlight or moisture.

• Never install telephone jacks in wet locations unless the jack is
specifically designed for wet locations.

• Avoid dropping and other rough treatment to the phone.

• Temporarily disconnect any equipment connected to the
phone such as faxes, other phones, or modems.

Your telephone should be placed on a level surface such as a
desk or table top, or you can mount it on a wall. A desktop/wall

3

1

2

Your telephone equipment is approved for connection to the Public Switched Telephone
Network and is in compliance with parts 15 and 68, FCC Rules and Regulations and the
Technical Requirements for Telephone Terminal Equipment published by ACTA.
Notification to the Local Telephone Company
On the bottom of this equipment is a label indicating, among other information, the US
number and Ringer Equivalence Number (REN) for the equipment. You must, upon request,
provide this information to your telephone company.
The REN is useful in determining the number of devices you may connect to your telephone
line and still have all of these devices ring when your telephone number is called. In most
(but not all) areas, the sum of the RENs of all devices connected to one line should not
exceed 5. To be certain of the number of devices you may connect to your line as
determined by the REN, you should contact your local telephone company.
A plug and jack used to connect this equipment to the premises wiring and telephone
network must comply with the applicable FCC Part 68 rules and requirements adopted by
the ACTA. A compliant telephone cord and modular plug is provided with this product. It is
designed to be connected to a compatible modular jack that is also compliant. See
installation instructions for details.
Notes
• This equipment may not be used on coin service provided by the telephone company.

2

•

Party lines are subject to state tariffs, and therefore, you may not be able to use your
own telephone equipment if you are on a party line. Check with your local telephone
company.

•

Notice must be given to the telephone company upon permanent disconnection of your
telephone from your line.

•

If your home has specially wired alarm equipment connected to the telephone line,
ensure the installation of this product does not disable your alarm equipment. If you
have questions about what will disable alarm equipment, consult your telephone
company or a qualified installer.

Rights of the Telephone Company
Should your equipment cause trouble on your line which may harm the telephone network, the
telephone company shall, where practicable, notify you that temporary discontinuance of
service may be required. Where prior notice is not practicable and the circumstances warrant
such action, the telephone company may temporarily discontinue service immediately. In case
of such temporary discontinuance, the telephone company must: (1) promptly notify you of such
temporary discontinuance; (2) afford you the opportunity to correct the situation; and (3) inform
you of your right to bring a complaint to the Commission pursuant to procedures set forth in
Subpart E of Part 68, FCC Rules and Regulations.
The telephone company may make changes in its communications facilities, equipment,
operations or procedures where such action is required in the operation of its business and not
inconsistent with FCC Rules and Regulations. If these changes are expected to affect the use or
performance of your telephone equipment, the telephone company must give you adequate notice,
in writing, to allow you to maintain uninterrupted service.

mounting pedestal is built into the base of the phone.
1. Slide the RINGER volume switch (on the handset) to the
desired volume.
2. Set the receiver volume switch (on the handset) to the desired
listening volume.
3. Plug the telephone line cord into a modular wall phone jack.
4. Feed the cord through the groves as shown in the picture
below.

Your telephone may also be mounted on a wall plate (not included).
1. Plug the telephone line cord into a modular wall phone jack.
2. Slip the mounting holes on the base over the wall plate posts and
firmly slide the unit down into place (wall plate not included).

WRAPPING THE TELEPHONE LINE CORD
In desktop or wall mount mode, you may want to wrap the
excess telephone line cord around the mounting bracket on the
bottom of the base.

TELEPHONE OPERATION
Ringer volume switch
redial button

ghi

Receiver
volume
switch

This telephone system meets FCC standards for Hearing Aid Compatibility.

RISK OF ELECTRIC SHOCK
DO NOT OPEN

WARNING: TO
PREVENT FIRE OR
ELECTRICAL SHOCK
HAZARD, DO NOT
EXPOSE THIS
PRODUCT TO RAIN
OR MOISTURE.

CAUTION: TO REDUCE THE
RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR
BACK). NO USER
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO
QUALIFIED SERVICE
PERSONNEL.

2

4

jkl

7

tuv

*

oper

tone

5

def

flash button

3
6

mno

9

8

wxyz

0

#

VOL

REDIAL
This unit redials up to 32 digits. To automatically redial the last
number you called:
1. Pick up the handset and wait for a dial tone.
2. Press the redial button.

CAUTION:
THE LIGHTNING
FLASH AND ARROW
HEAD WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
“DANGEROUS
VOLTAGE” INSIDE
THE PRODUCT.

flash

abc

pqrs

HEARING AID COMPATIBILITY (HAC)
US NUMBER IS LOCATED ON THE CABINET BOTTOM
REN NUMBER IS LOCATED ON THE CABINET BOTTOM

redial

1

THE EXCLAMATION
POINT WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
IMPORTANT
INSTRUCTIONS
ACCOMPANYING
THE PRODUCT.

SEE MARKING ON BOTTOM / BACK OF PRODUCT

FLASH
Press the flash button instead of the hook switch to activate
custom calling services such as call waiting or call transfer.
Custom calling services are provided by the phone company.

RECEIVER VOLUME
You may control the listening level with the volume switch on the
bottom of the handset. It has 3 levels: lo, mid, and high.

RINGER VOLUME
Model 29253
15929620 (Rev. 3 E/S)
02-51
Printed in China

ATLINKS USA, Inc.
101 West 103rd Street
Indianapolis, IN 46290
© 2002 ATLINKS USA, Inc.
Trademark(s) ® Registered
Marca(s) Registrada(s)

You may control the ringer volume level with the switch located
above the touch tone pad on the handset.
= ringer tone will be loud
= ringer tone will be low
= telephone will not ring.

If trouble is experienced with this equipment, for repair or
warranty information, please contact customer service at
1-800-448-0329. If the equipment is causing harm to the
telephone network, the telephone company may request that you
disconnect the equipment until the problem is resolved.
This product may be serviced only by the manufacturer or its
authorized service agents. Changes or modifications not
expressly approved by ATLINKS USA, Inc. could void the user’s
authority to operate this product. For instructions on how to
obtain service, refer to the warranty included in this guide or call
customer service at 1-800-448-0329.
Or refer inquiries to:
ATLINKS USA, Inc.
Manager, Consumer Relations
P O Box 1976
Indianapolis, IN 46206
Attach your sales receipt to the booklet for future reference or jot
down the date this product was purchased or received as a gift.
This information will be valuable if service should be required
during the warranty period.
Purchase date
______________________________________________________________
Name of store
______________________________________________________________

WALL MOUNT INSTALLATION

INTERFERENCE INFORMATION
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference; and (2) This device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna (that is, the antenna for radio or television that is
“receiving” the interference).
• Reorient or relocate and increase the separation between the telecommunications equipment
and receiving antenna.
• Connect the telecommunications equipment into an outlet on a circuit different from that to
which the receiving antenna is connected.
If these measures do not eliminate the interference, please consult your dealer or an experienced radio/
television technician for additional suggestions. Also, the Federal Communications Commission has
prepared a helpful booklet, “How To Identify and Resolve Radio/TV Interference Problems.” This booklet
is available from the U.S. Government Printing Office, Washington, D.C. 20402. Please specify stock
number 004-000-00345-4 when ordering copies.

• Never use a strong cleaning agent or abrasive powder
because this will damage the finish.

SERVICE

INSTALLING THE PHONE

EQUIPMENT APPROVAL INFORMATION

• Clean with a soft cloth.

• Retain the original packaging in case you need to ship the
phone at a later date.

• Use caution when installing or modifying telephone lines.

1

Other party cannot hear you.
• Make sure phone cord is securely plugged in.
• Make sure extension phones are on the hook at the same time you're using
the phone. It is normal for the volume to drop when additional extension
phones are used at the same time.
Phone "howls" when handset is placed near the base and handset volume level is
too high.
• This is normal feedback due to handset volume level being set to maximum.

GENERAL PRODUCT CARE

Modular
telephone
line jack

• Never touch non-insulated telephone wires or terminals, unless
the telephone line has been disconnected at the network
interface.

We bring good things to life.

Phone doesn’t ring.
• Make sure RINGER switch (located on the handset) is set to loud or low.
• Are you using too many phones on one line? (The total REN of all phones on
the same line should not be greater than the maximum REN for your calling
area. See Equipment Approval Information).

LIMITED WARRANTY
What your warranty covers:
•
Defects in materials or workmanship.
For how long after your purchase:
•
One year, from date of purchase.
(The warranty period for rental units begins with the first rental or 45 days
from date of shipment to the rental firm, whichever comes first.)
What we will do:
•
Provide you with a new or, at our option, a refurbished unit. The exchange
unit is under warranty for the remainder of the original product’s warranty
period.
How you get service:
•
Properly pack your unit. Include any cables, etc., which were originally
provided with the product. We recommend using the original carton and
packing materials.
•
”Proof of purchase in the form of a bill of sale or receipted invoice which is
evidence that the product is within the warranty period, must be presented
to obtain warranty service.” For rental firms, proof of first rental is also
required. Also print your name and address and a description of the defect.
Send via standard UPS or its equivalent to:
ATLINKS USA, Inc.
c/o Thomson
11721 B Alameda Ave.
Socorro, Texas 79927
•
Pay any charges billed to you by the Exchange Center for service not covered
by the warranty.
•
Insure your shipment for loss or damage. ATLINKS accepts no liability in
case of damage or loss.
•
A new or refurbished unit will be shipped to you freight prepaid.
What your warranty does not cover:
•
Customer instruction. (Your Owner’s Manual provides information regarding
operating instructions and user controls. Any additional information, should
be obtained from your dealer.)
•
Installation and setup service adjustments.
•
Batteries.
•
Damage from misuse or neglect.
•
Products which have been modified or incorporated into other products.
•
Products purchased or serviced outside the USA.
•
Acts of nature, such as but not limited to lightning damage.
Product Registration:
•
Please complete and mail the Product Registration Card packed with your
unit. It will make it easier to contact you should it ever be necessary. The
return of the card is not required for warranty coverage.
Limitation of Warranty:
•
THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY APPLICABLE TO
THIS PRODUCT. ALL OTHER WARRANTIES, EXPRESS OR IMPLIED
(INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE) ARE HEREBY DISCLAIMED. NO VERBAL OR
WRITTEN INFORMATION GIVEN BY ATLINKS USA, INC., ITS AGENTS, OR
EMPLOYEES SHALL CREATE A GUARANTY OR IN ANY WAY INCREASE THE
SCOPE OF THIS WARRANTY.
•
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE
EXCLUSIVE REMEDY OF THE CONSUMER. ATLINKS USA, INC. SHALL NOT
BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING
FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF
ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. THIS
DISCLAIMER OF WARRANTIES AND LIMITED WARRANTY ARE GOVERNED
BY THE LAWS OF THE STATE OF INDIANA. EXCEPT TO THE EXTENT
PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS
PRODUCT IS LIMITED TO THE APPLICABLE WARRANTY PERIOD SET FORTH
ABOVE.
How state law relates to this warranty:
•
Some states do not allow the exclusion nor limitation of incidental or
consequential damages, or limitations on how long an implied warranty lasts
so the above limitations or exclusions may not apply to you.
•
This warranty gives you specific legal rights, and you also may have other
rights that vary from state to state.
If you purchased your product outside the USA:
•
This warranty does not apply. Contact your dealer for warranty information.

Serie 29253
Teléfono de Línea Delgada
Guía del Usuario

INTRODUCCIÓN

SOLUCIÓN DE PROBLEMAS

Su teléfono inalámbrico /máquina contestadora con Identificador de
Llamadas está diseñado para darle flexibilidad de uso y funcionamiento
de alta calidad. Para obtener el máximo rendimiento de su teléfono
inalámbrico /máquina contestadora, le sugerimos se tome unos minutos
ahora mismo para leer este manual de instrucciones.

No hay tono de marcar.
• Oprima y suelte el gancho de colgar. Verifique el gancho: ¿se levanta
completamente cuando usted descuelga?

CUIDADO: Cuando utilice equipo telefónico, hay
instrucciones básicas de seguridad que siempre deben
seguirse. Refiérase a la guía de INSTRUCCIONES DE
SEGURIDAD IMPORTANTES provista con este producto
y guárdela para referencia futura.
NOTA: Este teléfono utiliza únicamente modalidad para
marcado por Tono. Para que este teléfono funcione
adecuadamente, usted debe tener el servicio de Tono disponible
para usted a partir de su compañía telefónica local.

ANTES DE COMENZAR
Placa de pared

REQUERIMIENTOS PARA ENCHUFE
TELEFÓNICO
Para utilizar este teléfono, usted puede
necesitar un enchufe modular telefónico tipo
RJ11C como el ilustrado aquí, instalado en su
hogar. Si usted no tiene este tipo de enchufe,
llame a su compañía telefónica local para
preguntar cómo conseguirlo.

Enchufe
telefónico
modular

• Nunca instale enchufes telefónicos en localizaciones mojadas, a
menos que el enchufe esté específicamente diseñado para mojarse.
• Nunca toque cables o terminales no aislados, a menos que la línea
telefónica haya sido desconectada en la interfaz de la red.
• Utilice precaución cuando instale o modifique líneas telefónicas.
• Desconecte temporalmente cualquier equipo conectado con el
aparato telefónico como máquinas de fax, otros teléfonos, o
módems.

El equipo de su teléfono esta aprobado para la conexión con la red Telefónica Pública (Public
Switched Telephone Network) y cumple con los requisitos establecidos en las secciones 15 y 68 de
las Reglas y Regulaciones de la FCC y con los Requerimientos Técnicos para Equipos de Terminales
Telefónicas (Technical Requirements for Telephone Terminal Equipment), publicado por ACTA.
1

Notificación a la Compañía Telefónica Local
En la parte de abajo de este equipo hay una etiqueta que indica, entre otra información, el
número de US y el Número de Equivalencia de Timbres (REN) para este equipo. Usted debe,
cuando sea requerido, proveer esta información a su compañía telefónica.
El REN es útil para determinar el número total de artefactos que Ud. puede conectar a su línea
telefónica, todavía asegurando que todos estos artefactos sonarán cuando se llame su
número telefónico. En la mayoría de las áreas (pero no en todas), el total de los números REN
de todos los artefactos conectados a una línea no debe exceder 5. Para estar seguro del
número total de artefactos que Ud. pueda conectar a su línea (determinado por el REN), Ud.
deberá ponerse en contacto con su compañía telefónica local.
Cualquier enchufe y conexión que se utilice para conectar este equipo al cableado del edificio
y a la red telefónica, debe estar en conformidad con el reglamento de la FCC Parte 68 que ha
sido adoptado por la ACTA. Un cable telefónico y un enchufe modular que han sido aprobados
y están en conformidad con dicho reglamento han sido provistos con este producto. Están
diseñados para ser conectados a un enchufe modular compatible, que también esté en
conformidad. Para más detalles, vea las instrucciones para la instalación.
NOTAS:
• No se puede usar este equipo con un teléfono de previo pago proveído por la compañía
telefónica.
• Las líneas compartidas son sujetas a las tarifas del estado, y por eso, es posible que
Ud. no pueda usar su propio equipo telefónico si Ud. estuviera compartiendo la misma
línea telefónica con otros abonados.
• Se debe notificar la compañía telefónica cuando se desconecte permanentemente su
teléfono de la línea.
• Si su casa tiene algún equipo de alarma especial conectado a la línea telefónica,
asegúrese que la instalación de este producto no desactive su equipo de alarma. Si
usted tiene alguna pregunta sobre qué puede desactivar su equipo de alarma, consulte
a su compañía telefónica o a un instalador calificado.

2

Derechos de la Compañía Telefónica
Si su equipo causase algún problema en su línea que pudiera dañar la red telefónica, la
compañía telefónica siempre que sea posible le avisará de la posible interrupción
temporal de su servicio. En caso que la compañía no pudiera avisarle de antemano y
hubiera necesidad de tomar tal acción, la compañía telefónica podrá interrumpir su
servicio inmediatemente. En caso de tal interrupción telefónica temporal la compañía
debe : (1) darle aviso al momento de tal interrupción temporal de servico, (2) concederle a
Ud. la oportunidad de corregir la situación, (3) informarle a Ud. de sus derechos de
presentar una questa a la Comisión de acuerdo con los procedimientos dictados en la
Subparte E de la Parte 68 de las Regulaciones y Reglas de la FCC.
La compañía telefónica puede hacer los cambios en sus instalaciones de comunicación,
en equipos, en sus funcionamientos o procedimientos que digne necesarios para el
manejo de sus negocios y que no sean incompatibles con las Reglas y Regulaciones de l
a FCC. Si estos cambios pudieran alterar el uso o el funcionamiento de su equipo
telefónico, la compañía telefónica deberá darle aviso adecuado en escrito para que Ud.
goce de un servico ininterrumpido.

Su teléfono inalámbrico/ sistema contestador debe ser colocado en
una superficie plana como un escritorio o sobre una mesa, o se
puede instalar sobre la pared. Un pedestal para montaje está
integrado en la base del teléfono.

3

1

Adjunte su recibo al folleto, para futura referencia, o anote la fecha en
la que se compró o recibió este producto como regalo. Esta
información será valiosa si se llegase a requerir durante el período de
garantía.

2. Programe el selector de volumen del recibidor (en el auricular) al
nivel de volumen deseado.

Fecha de compra__________________________________________________

3. Enchufe la línea de cable telefónico en un enchufe modular de pared.

Nombre de la tienda______________________________________________

4. Alimente el cable a través de las ranuras como se muestra en el
dibujo abajo.

MONTAJE SOBRE PARED
Su teléfono puede ser montado en una placa de pared (no incluida).
1. Conecte el cable de línea en un enchufe modular de pared.
2. Deslice los agujeros para montaje de la base sobre los postecitos
de pared y deslice firmemente el aparato hacia abajo hasta que
quede en su lugar (placa de pared no incluida).

PARA GUARDAR EL CABLE DE LÍNEA
Tanto en modalidad de superficie plana como de pared, usted puede
querer almacenar el cable excedente alrededor de la placa para
montaje en la parte de debajo de la base.

Botón para volver a marcar
(“REDIAL”)

COMPATIBILIDAD CON AUDÍFONOS (CCA)

1. Levante el auricular y espere al tono de marcar.

Se juzga que este teléfono es compatible con audífonos, en base a las normas de la FCC.

2. Oprima el botón para volver a marcar (“redial”).

ADVERTENCIA: PARA
PREVENIR
EL RIESGO DE
UNFUEGO O DE UNA
SACUDIDA
ELECTRICA, NO
EXPONGA
ESTE APARATO A LA
LLUVIA O A LA
HUMEDAD.

Modelo 29253
15929620 (Rev. 3 E/S)
02-51
Impreso en China

RIESGO DE SACUDIDA
ELÉCTRICA NO ABRA
EL RELÁMPAGO Y LA
PUNTA DE FLECHA
DENTRO DEL TRIÁNGULO
ES UNA SEÑAL DE
ADVERTENCIA,
ALERTÁNDOLE A UD. DE
QUE HAY "VOLTAJE
PELIGROSO" DENTRO DEL
PRODUCTO.

CUIDADO: PARA REDUCIR
EL RIESGO DE UNA SACUDIDA
ELÉCTRICA, NO QUITE LA
CUBIERTA (O PARTE
POSTERIOR) NO USE PARTES
DE REPUESTO DENTRO.
CONSULTE A ALGUNA
PERSONA CALIFICADA DEL
SERVICIO DE REPARACIONES.

EL SIGNO DE
EXCLAMACIÓN DENTRO
DEL TRIÁNGULO ES UNA
SEÑAL DE
ADVERTENCIA,
ALTERTÁNDOLE A UD. DE
QUE EL PRODUCTO, TRAE
INCLUCIDO,
INSTRUCTIONES MUY
IMPORTANTES.

VEA ADVERTENCIA EN LA PARTE POSTERIOR/BASE DEL PRODUCTO.

ATLINKS USA, Inc.
101 West 103rd Street
Indianapolis, IN 46290
© 2002 ATLINKS USA, Inc.
Trademark(s) ® Registered
Marca(s) Registrada(s)

Este producto puede únicamente ser reparado por el fabricante o sus
agentes de reparación autorizados. Cualquier cambio o modificación
no aprobados expresamente por ATLINKS USA, Inc. podría ser
motivo de anulación de la autoridad del usuario para operar este
producto. Para recibir instrucciones sobre cómo obtener servicios de
mantenimiento, por favor consulte la garantía incluida en esta Guía, o
llame a Información para el Usuario, 1-800-448-0329.

1. Deslice el selector de volumen del timbre (“RINGER”) (en el
auricular) al nivel de volumen deseado.

Este artefacto cumple con la Parte 15 de las Reglas de la FCC. Su funcionamiento es sujeto a las dos
condiciones siguientes: (l) Este artefacto no puede causar interferencia dañosa, y (2) Este artefacto
debe aceptar cualquier interferencia recibida, incluyendo interferencia que puede causar un
funcionamiento no deseado.
Este equipo ha sido probado y cumple con los límites para un artefacto digital de la Clase B, de
conformidad con la Parte 15 de las Reglas de la FCC. Estos límites han sido diseñados para
proporcionar una protección razonable contra una interferencia dañosa que pueda existir en
una instalación doméstica.
Este equipo genera, usa y puede radiar la energía de frecuencia de una radio y, si no fuera
instalado y usado de acuerdo con las instrucciones, puede causar interferencia dañosa a las
transmisiones radiales. Sin embargo, no hay garantía que la interferencia no ocurrirá en una
instalación en particular.
Si este equipo causa en efecto una interferencia dañosa a la recepción de la radio o de la
televisión, lo cual puede ser determinado apagando y prendiendo el equipo, le animamos a Ud.
de tratar de corregir la interferencia por medio de una (o más) de las sugerencias siguientes:
•
Cambie la posición o la ubicación de la antena (quiere decir la antena de la radio o de la
televisión que está recibiendo la interferencia).
•
Cambie la posición o cambie la ubicación y aumente la distancia entre el equipo de
telecomunicaciones y la antena receptora de la radio o de la televisión que está recibiendo la
interferencia.
•
Conecte el equipo de telecomunicaciones a una toma en un circuito diferente del circuito
al cual la antena receptora esté conectada.
Si estas medidas no eliminan la interferencia, favor de consultar a su distribuidor o a un
técnico de radio/televisión experto por otras sugerencias. También, la Comisión Federal de
Comunicaciones (FCC) ha preparado un folleto muy útil, “How To Identify and Resolve Radio/TV
Interference Problems” (“Como Identificar y Resolver Problemas de Interferencia de Radio/
Televisión”). Este folleto se puede obtener del U.S. Goverment Printing Office, Washington, D.C.
20402. Favor de especificar el número 004-000-00345-4 cuando haga su pedido.

ATTENTION:

Si usted experimenta problemas con este equipo, para reparaciones o
para información de garantía, comuníquese con el departamento de
servicio al cliente al 1-800-448-0329. Si el equipo está causando daños
a la red telefónica, la compañía telefónica puede pedirle que
desconecte su equipo hasta que el problema haya sido resuelto.

O envíe sus preguntas a:
ATLINKS USA, Inc.
Gerente, Servicio al Consumidor
P.O. Box 1976
Indianápolis, IN 46206

INFORMACIÓN DE INTERFERENCIAS

El número de la US está ubicado en el fondo de la base
El numero REN esta ubicado en el fondo de la base

• Evite poner el teléfono cerca de calentadores (calefactores) de
ambiente y dispositivos que generen interferencia eléctrica
ejemplo, motores o lámparas fluorescentes).
• No lo exponga a la luz solar directa o a la humedad.
• No deje caer la extensión móvil y no maltrate el teléfono.
• Limpie el teléfono con un trapo suave
• Nunca use un agente de limpieza fuerte ni un polvo abrasivo, ya
que esto dañará el acabado.
• Retenga el empaque original en caso de que necesite embarcar el
auricular en el futuro.

CÓMO OBTENER SERVICIOS DE MANTENIMIENTO

PARA INSTALAR EL TELÉFONO

2

El teléfono “aúlla” cuando el auricular es colocado cerca de la base y el nivel
volumen del auricular del auricular esta muy alto.
• Esto es normal debido a que el volumen del auricular ha sido programado al
máximo nivel.

Para mantener su teléfono funcionando bien y con buena apariencia,
observe las siguientes pautas:

• Nunca instale cableado telefónico durante una tormenta de
relámpagos.

INFORMACIÓN SOBRE LA APROBACIÓN DE EQUIPO

La otra persona no le escucha.
• Asegúrese que el cable esté conectado adecuadamente.
• Asegúrese que otras extensiones estén colgadas mientras usted está usando el
teléfono. Es normal que el volumen disminuya si otras extensiones son
descolgadas al mismo tiempo.

CUIDADO GENERAL DEL PRODUCTO

INFORMACIÓN IMPORTANTE PARA LA INSTALACIÓN

Creamos cosas buenas para la vida.

El auricular no timbra.
• Asegúrese de que el timbre (“RINGER”) (localizado en el auricular) esté en
posición de alto o bajo.
• ¿Tiene usted demasiadas extensiones en una línea? El número total de REN de
todos los teléfonos en esta línea no debe ser mayor que el máximo REN para su
área. Vea la Sección de Aprobación de Equipo).

OPERACIÓN DEL TELEFONO
Selector de Volumen del
Timbre (“RINGER”)
redial

1
ghi

2

5

4

jkl

7

tuv

*

oper

pqrs

Selector de volumen (“vol”) el
Recibidor

flash

abc

tone

def

3

Botón para
servicios (“flash”)

6

mno

9

8

wxyz

0

#

VOL

PARA VOLVER A MARCAR (“REDIAL”)
Este aparato vuelve a marcar hasta 32 dígitos. Para volver a marcar
automáticamente el último número al que usted llamó:

BOTÓN DE SERVICIOS ESPECIALES (“FLASH”)
Oprima el botón de Flash en lugar del gancho de colgar para activar los
servicios especiales como llamada en espera o transferencia de llamada.
Estos servicios especiales son provistos por su compañía telefónica.

VOLUMEN EL RECIBIDOR
Usted puede controlar el nivel de volumen con el selector de
volumen localizado en la parte de abajo del auricular. Tiene 3 niveles:
bajo, medio y alto (“lo,” “mid,” y “high”).

VOLUMEN DEL TIMBRE
Usted puede controlar el volumen del timbre con el selector
localizado en arribe del teclado numérico en el auricular.
= el tono del timbre será alto
= el tono del timbre será bajo
= el teléfono no timbrará.

GARANTÍA LIMITADA
Lo que cubre su garantía:
•
Defectos de materiales o de trabajo.
Por cuánto tiempo después de la compra:
•
Un año, a partir de la fecha de compra.
(El periodo de garantía para unidades arrendadas se inicia con la primera renta o 45 días
de la fecha del embarque a la firma de arrendamiento, lo que ocurra primero).
Lo que haremos:
•
Proporcionarle una unidad nueva o, a nuestra opción, una reacondicionada. La unidad de
intercambio quedará bajo garantía por el resto del periodo de garantía del producto
original.
Cómo obtener servicio:
•
Empaque bien la unidad, incluyendo todos los cables, etc., que originalmente venían con
el producto. Se recomienda usar el cartón y materiales de empaque originales.
•
“Prueba de compra como factura o recibo de compra, que ofrezca evidencia de que el
producto está dentro del periodo de garantía, debe ser presentado para obtener servicio
bajo garantía.” Para compañías de arrendamiento, se requiere como evidencia el primer
contrato de renta. También escriba claramente su nombre, dirección y la descripción del
defecto. Mande vía UPS o un servicio de paquetería equivalente a:
ATLINKS USA, Inc.
c/o Thomson
11721 B Alameda Ave.
Socorro, Texas 79927
•
Pague cualquier cargo que le facture el Centro de Intercambio por servicio que no esté
cubierto por garantía.
•
Asegure su empaque para prevenir pérdida o daño. ATLINKS no acepta responsabilidad
en caso de pérdida o daño.
•
Un aparato nuevo o uno remozado se le enviará con los cargos pagados.
Lo que no cubre la garantía:
•
Instrucciones al cliente. (Su manual de propietario le proporciona la información con
respecto a las instrucciones de operación y los controles del usuario. Cualquier
información adicional debe obtenerse con su agente de ventas.
•
Ajustes de instalación y de preparación del servicio.
•
Baterías.
•
Daño por mal uso o negligencia.
•
Productos que han sido modificados o incorporados a otros productos.
•
Productos comprados o que han recibido servicio fuera de los Estados Unidos.
•
Desastres naturales, por ejemplo y sin limitarse a ellos, daños por relámpagos.
Registro del Producto:
•
Por favor llene y envíe por correo la Tarjeta de Registro del Producto que se embarcó con
su producto. Hará más fácil que hagamos contacto con usted si fuera necesario. No se
requiere la devolución de la tarjeta para tener la cobertura de la garantía.
Limitaciones sobre la Garantía:
•
LA GARANTÍA ESPECIFICADA ANTERIORMENTE ES LA ÚNICA GARANTÍA APLICABLE A
ESTE PRODUCTO. CUALQUIER OTRA GARANTÍA, EXPRESA O IMPLÍCITA (INCLUYENDO
TODAS LAS GARANTÍAS IMPLÍCITAS DE MERCADO O DE SALUD PARA CUALQUIER
PROPÓSITO) SON CONSIDERADAS NO VÁLIDAS. NINGUNA INFORMACIÓN VERBAL O
ESCRITA OTORGADA POR ATLINKS USA,INC., SUS AGENTES, O EMPLEADOS SERÁ
CONSIDERADA PARA CREAR UNA GARANTÍA NI PARA AUMENTAR BAJO NINGUNA
CIRCUNSTANCIA LA COBERTURA DE ESTA GARANTÍA.
•
LA REPARACIÓN O REEMPLAZO DE UN PRODUCTO COMO SE ESPECIFICA BAJO ESTA
GARANTÍA ES EL REMEDIO EXCLUSIVO DEL CONSUMIDOR. ATLINKS USA, INC. NO SE
HACE RESPONSIBLE POR DAÑOS INCIDENTALES, DAÑOS DERIVADOS COMO
CONSECUENCIA DEL USO DE ESTE PRODUCTO, O COMO RESULTADO DEL
INCUMPLIMIENTO DE CUALQUIER GARANTÍA IMPLÍCITA O EXPRESA DE ESTE
PRODUCTO. LA INVALIDEZ DE LAS GARANTÍAS O LAS GARANTÍAS LIMITADAS ESTÁN
REGLAMENTADAS POR LAS LEYES DEL ESTADO DE INDIANA. EXCEPTO POR EL ALCANCE
ESTABLECIDO POR LAS LEYES APLICABLES, CUALQUIER GARANTÍA IMPLÍCITA DE
MERCADO O DE SALUD PARA CUALQUIER PROPÓSITO, EN ESTE PRODUCTO ES LIMITADA
AL PERÍODO DE GARANTÍA ESPECIFICADO ANTERIORMENTE.
Cómo se Relaciona la Ley Estatal a esta Garantía:
•
Algunos estados no permiten la exclusión ni limitación de daño incidental o derivado de
alguna consecuencia, o la limitación con respecto al período de tiempo que debe
aplicarse para garantías implícitas, por lo tanto las limitaciones y exclusiones
mencionadas anteriormente pueden no ser aplicables para usted.
•
Esta garantía le ofrece derechos legales específicos, y usted puede tener otros derechos
legales que varían de estado a estado.
Si compró su producto fuera de los Estados Unidos:
•
Esta garantía no se aplica. Vea a su distribuidor para información sobre la garantía.



Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Warning                         : Info object (6 0 obj) not found at 119409
EXIF Metadata provided by EXIF.tools

Navigation menu