Tyco Safety Canada 01NB918 WLS918-433NA & PWLS918-433NA User Manual

Digital Security Controls Ltd. WLS918-433NA & PWLS918-433NA Users manual

a href="https://usermanual.wiki/Tyco-Safety-Canada" itemprop="url"> Tyco Safety Canada >

Users manual

The WLS918 Wireless Panic Pendant is a devicedesigned to transmit an emergency signal from anylocation within the range of the alarm system with whichit is used. Signals from the pendant will be transmittedwhether your alarm system is armed or disarmed.The pendant can be attached to a lanyard or a belt clip.The unit is even small and lightweight enough to beplaced in a shirt pocket or tucked inside a purse. Thependant is also water resistant. Signals will not be transmitted if the pendant isnot within the range of the wireless receiver.To activate an alarm, press and hold both large outerbuttons for two seconds. If the cap is not replaced, the LED will remain onuntil the cap is restored.Components of the WLS918The WLS918 is made up of the following components:• Cap - whether it is the tear away cap with attached lanyard (neck strap)or the cap with attached belt clip.• Rubber Boot - this boot adds water resistance to the product andprovides a soft grip to be able to easily grab the unit to tear it away orpush the activation buttons• Clear Plastic Housing - the plastic housing holds the circuit board ofthe WLS918 and is put inside the rubber boot• LED - (Light indication) - the LED is used to indicate various conditionsof the pendant and can be seen through the side of the clear plastichousing that is not covered by the rubber boot.• Lithium battery - the WLS918 is powered by a user replaceable lithiumbatteryAssembling the WLS918:Tear Away Assembly:1. The WLS918 comes set up for tear away operation by default. The tearaway cap will already be connected to the clear plastic housing.2. Remove the cover over the bottom of the clear plastic housing3. Put the battery into the pendant (please see ‘Replacing the Battery’ forproper orientation)4. Insert the clear plastic housing into the rubber boot© 2001 Digital Security Controls Ltd.Printed in Canada 29005932 R001WLS918-433Wireless Panic PendantOPERATING INSTRUCTIONSFCC COMPLIANCE STATEMENTCAUTION: Changes or modifications not expressly approved by Digital Security Controls Ltd. could void yourauthority to use this equipment.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant toPart 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer-ence in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, ifnot installed and used in accordance with the instructions, may cause harmful interference to radio communica-tions. However, there is no guarantee that interference will not occur in a particular installation. If this equip-ment does cause harmful interference to radio or television reception, which can be determined by turning theequipment off and on, the user is encouraged to try to correct the interference by one or more of the followingmeasures:nRe-orient the receiving antenna.nIncrease the separation between the equipment and receiver.nConnect the equipment into an outlet on a circuit different from that to which the receiver is connected.nConsult the dealer or an experienced radio/television technician for help.The user may find the following booklet prepared by the FCC useful: “How to Identify and Resolve Radio/Television Interference Problems”. This booklet is available from the U.S. Government Printing Office, Wash-ington D.C. 20402, Stock # 004-000-00345-4.Digital Security Controls Ltd. 160 Washburn St., Lockport, NY 14094This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions:(1) this device may not cause interference, and (2) this device must accept any interference, includinginterference that may cause undesired operation of the device.Ce dispositif satisfait aux exigences d’Industrie Canada, prescrites dans le document CNR-210. son utilisationest autorisée seulement aux conditions suivantes: (1) il ne doit pas produire de brouillage et (2) l’utilisateurdu dispositif doit être prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptiblede compromettre le fonctionnement du dispositif.LIMITED WARRANTYDigital Security Controls Ltd. warrants that for a period of twelve months from the date ofpurchase, the product shall be free of defect in materials and workmanship under normal useand that in fulfilment of any breach of such warranty, Digital Security Controls Ltd. shall, at itsoption, repair or replace the defective equipment upon return of the equipment to its repairdepot. This warranty applies only to defects in parts and workmanship and not to damageincurred in shipping or handling, or damage due to causes beyond the control of DigitalSecurity Controls Ltd. such as lightning, excessive voltage, mechanical shock, water damage,or damage arising out of abuse, alteration or improper application of the equipment.The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of anyand all other warranties, whether expressed or implied and of all other obligations or liabilitieson the part of Digital Security Controls Ltd. This warranty contains the entire warranty. DigitalSecurity Controls Ltd. neither assumes responsibility for, nor authorizes any other personpurporting to act on its behalf to modify or to change this warranty, nor to assume for it anyother warranty or liability concerning this product.In no event shall Digital Security Controls Ltd. be liable for any direct, indirect or consequentialdamages, loss of anticipated profits, loss of time or any other losses incurred by the buyer inconnection with the purchase, installation or operation or failure of this product.WARNING: Digital Security Controls Ltd. recommends that the entire system be com-pletely tested on a regular basis. However, despite frequent testing, and due to, but notlimited to, criminal tampering or electrical disruption, it is possible for this product to failto perform as expected.
Belt Clip Assembly:1. Remove the tear away cap from the clear plastic housing.2. Break off the plastic tab that is permanently affixed to the top of the clearplastic housing of the pendant.3. Snap on the belt clip cap.4. Put the battery into the pendant (please see ‘Replacing the Battery’ for properorientation).5. Insert the clear plastic housing into the rubber bootTesting the WLS918The pendant should be tested on a weekly basis along with the rest of the alarmsystem. For full system testing instructions, please consult your control panelInstruction Manual.To Test the Pendant:1. Begin testing when your system is in the ready state and the keypad Ready(Green) light is ON.2. Press and hold either of the 2 buttons for 5 seconds. When the button hasbeen held long enough the LED in the pendant will turn ON steady for 2seconds. Once the test transmission signal from the pendant has beenreceived by the alarm system and the pendant’s battery condition is normal,the Ready light of the keypad will turn OFF for approx. 5 seconds.3. If the pendant’s battery is low, the keypad Trouble (yellow) Light will turn ONand a series of continuous keypad beeps will be heard.Signals will not be received and processed if the pendant is not withinrange of the alarm system.When the WLS918 has a low battery, it will flash the LED once every 10seconds until the battery is replaced.When the unit detects a low battery, it will flash the LED once every 10seconds until the battery is replaced.Activating an AlarmAn alarm can be generated via the WLS918 in a few different ways:1. Press and hold both buttons simultaneously for 2 seconds or2. When using the tear away version, pull down on the unit until the cap breaksaway from the body of the WLS918 or3. When using the belt clip version, pull down on the unit until the cap breaksaway from the body of the WLS918.Replacing the Battery1. Remove the rubber boot that covers the clear plastic housing. You can do thisby placing your fingernails in between the top of the rubber boot and thebottom of the plastic cap then pull up on the plastic and down on the boot toseparate them.2. Remove the plastic battery cover at the bottom of the plastic housing.3. Pull out the old lithium battery.4. Insert the new lithium battery ensuring that the negative side of the batteryfaces the green PCB (printed circuit board).5. Replace the battery cover.6. Insert the clear plastic housing back into the rubber boot.7. Test the WLS918 as per the testing instructions. Only use battery type FDK CR2032 as a replacement for this product. The polarity of the batteries must be observed, as shown in thediagram above. Improper handling of lithium batteries may result inheat generation, explosion or fire, which may lead to personal injuries.WARNING: DANGER OF EXPLOSION IF BATTERIES ARE INSTALLEDINCORRECTLY. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPERECOMMENDED BY THE MANUFACTURER.Keep away from small children. If batteries are swallowed, promptly see a doctor.Do not try to recharge these batteries. Disposal of used batteries must be made inaccordance with the waste recovery and recycling regulations in your area.+F D KLITHIUM BATTERYCR20323V+F D KLITHIUM BATTERYCR20323V+
Belt Clip Assembly:1. Remove the tear away cap from the clear plastic housing.2. Break off the plastic tab that is permanently affixed to the top of the clearplastic housing of the pendant.3. Snap on the belt clip cap.4. Put the battery into the pendant (please see ‘Replacing the Battery’ for properorientation).5. Insert the clear plastic housing into the rubber bootTesting the WLS918The pendant should be tested on a weekly basis along with the rest of the alarmsystem. For full system testing instructions, please consult your control panelInstruction Manual.To Test the Pendant:1. Begin testing when your system is in the ready state and the keypad Ready(Green) light is ON.2. Press and hold either of the 2 buttons for 5 seconds. When the button hasbeen held long enough the LED in the pendant will turn ON steady for 2seconds. Once the test transmission signal from the pendant has beenreceived by the alarm system and the pendant’s battery condition is normal,the Ready light of the keypad will turn OFF for approx. 5 seconds.3. If the pendant’s battery is low, the keypad Trouble (yellow) Light will turn ONand a series of continuous keypad beeps will be heard.Signals will not be received and processed if the pendant is not withinrange of the alarm system.When the WLS918 has a low battery, it will flash the LED once every 10seconds until the battery is replaced.When the unit detects a low battery, it will flash the LED once every 10seconds until the battery is replaced.Activating an AlarmAn alarm can be generated via the WLS918 in a few different ways:1. Press and hold both buttons simultaneously for 2 seconds or2. When using the tear away version, pull down on the unit until the cap breaksaway from the body of the WLS918 or3. When using the belt clip version, pull down on the unit until the cap breaksaway from the body of the WLS918.Replacing the Battery1. Remove the rubber boot that covers the clear plastic housing. You can do thisby placing your fingernails in between the top of the rubber boot and thebottom of the plastic cap then pull up on the plastic and down on the boot toseparate them.2. Remove the plastic battery cover at the bottom of the plastic housing.3. Pull out the old lithium battery.4. Insert the new lithium battery ensuring that the negative side of the batteryfaces the green PCB (printed circuit board).5. Replace the battery cover.6. Insert the clear plastic housing back into the rubber boot.7. Test the WLS918 as per the testing instructions. Only use battery type FDK CR2032 as a replacement for this product. The polarity of the batteries must be observed, as shown in thediagram above. Improper handling of lithium batteries may result inheat generation, explosion or fire, which may lead to personal injuries.WARNING: DANGER OF EXPLOSION IF BATTERIES ARE INSTALLEDINCORRECTLY. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPERECOMMENDED BY THE MANUFACTURER.Keep away from small children. If batteries are swallowed, promptly see a doctor.Do not try to recharge these batteries. Disposal of used batteries must be made inaccordance with the waste recovery and recycling regulations in your area.+F D KLITHIUM BATTERYCR20323V+F D KLITHIUM BATTERYCR20323V+
Download:
Mirror Download [FCC.gov]
Document ID178232
Application ID2hKM3Vz8DPOhxAPwXt2NJQ==
Document DescriptionUsers manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize6.16kB (76976 bits)
Date Submitted2001-11-07 00:00:00
Date Available2001-11-07 00:00:00
Creation Date2001-08-14 14:33:13
Producing SoftwareAcrobat Distiller 4.05 for Windows
Document Lastmod2001-08-14 14:35:25
Document TitleUsers manual
FCC ID Filing: F5301NB918

Navigation menu