Tyco Safety Canada 09WS4913 Wireless CO Alarm User Manual

Digital Security Controls Ltd. Wireless CO Alarm WS4913 draft

a href="https://usermanual.wiki/Tyco-Safety-Canada" itemprop="url"> Tyco Safety Canada >

User Manual

1 WS4913 Series Wireless Carbon Monoxide Alarm Installation and Operating Instruction Read this instruction sheet thoroughly before installation and use of the WS4913 wireless carbon monoxide alarm Introduction The WS4913 is a wireless electrochemical Carbon Monoxide alarm , which is effective for detecting any buildup of carbon monoxide , also known as CO gas, in your home or office. The features of your CO alarm includes: (1) Easy to install. (2) Monitoring for carbon monoxide in a continuous manner. (3) Giving a loud alarm (85 dB) when it detects a buildup of carbon monoxide. (4) Having a Test button for you to test the CO alarm anytime. (5) Self-diagnostic testing its operative function continuously. (6) Complying the requirements of UL Standard 2034, 2075, UL Canada ULC and EU standard EN50291. Operation The green LED flashes approx. once in 60 seconds , which means the unit is receiving power and also indicates it is sensing carbon monoxide level in the air. CO alarm The CO alarm unit will go into alarm when the CO concentration level around the area exceeds the 'alarm' threshold, During an alarm, the red LED light flashes rapidly and buzzer sounds with repeating 4 quick beeps and pause 5 seconds and then 4 quick beeps. Tamper The removal of the CO alarm from the mounting plate initiates a 'tamper' transmission. The horn chirps once in a minute and the yellow LED is steadily on until the unit is mounted back to the plate. Wireless Transmissions Battery: The WS4913 is powered by a 3V DC lithium battery. ▲WARNING: Use only battery specified as above mentioned. Use of a different battery may have a detrimental effect on alarm operation. Installing/Replacing battery: (1) Open the battery cover to expose the battery compartment.. (2) Remove the old battery and properly dispose of them as recommended by the battery manufacturer. (3) Note the polarities of the battery are correctly installed as per the polarity marking indicated on two sides of the battery cover,make sure to carefully seat the red battery warning flag in the recess of the battery compartment. (4) Gently close the battery cover. The battery cover of CO alarm will not close if battery is not properly installed. ▲Caution: Constant exposures to high or low temperatures or high humidity may reduce battery life. The low battery threshold is set so the battery will provide no less than 30 days of operation and at that point the CO alarm will send a 'low battery' signal. If the battery is low ,horn will 'chirp' once every 60 seconds with yellow LED flash until battery failure. Please replace the battery asap before battery power is completely exhausted. ▲Caution: Constan exposures to high or low temperatures or high humidity may reduce battery life. The low battery threshold is set so the battery will provide no less than 30 days of operation and at that point the CO alarm will send a 'low battery' signal. If the battery is low ,horn will 'chirp' once every 60 seconds with yellow LED flash until battery failure. Please replace the battery asap before battery power is completely exhausted. Installation Instructions Locations to install your CO alarm Since CO gas moves freely in the air, the suggested location is in or as near as possible to sleeping areas of the home. The human body is most vulnerable to the effects of CO gas during sleeping hours. For maximum protection, a CO alarm should be located outside primary sleeping areas or on each level of your home. In the figure 1 below, are suggested locations in the home. The electronic sensor detects carbon monoxide, measures the concentration and sounds a loud alarm before a potentially harmful level is reached. Do not place the CO alarm in the following areas: (a) Where the temperature may drop below 40℉ (4.4℃) or exceed 100℉ (37.8℃) (b) Near paint thinner fumes (c) Within 5 feet (1.5 meter) of open flame appliances such as furnaces, stoves and fireplaces (d) In exhaust streams from gas engines, vents, flues or chimneys (e) Do not place in close proximity to an automobile exhaust pipe; this will damage the Alarm Installing your CO alarm Your WS4913 CO alarm is easy to install to protect you and your family in your home, cottage, cabin and office. To install the CO alarm (See figure 2 as below) : 1. At the place where you are going to install the alarm, draw a horizontal line six (6) inches long. 2. Remove the mounting bracket from your unit by rotating it counterclockwise. 3. Place the bracket so that the two longest hole slots are aligned on the line. In each of keyhole slots, draw a mark to locate a mounting plug and screw. 4. Remove the bracket. 5. Using a 3/16-inch (5mm) drill bit, drill two holes at the marks and insert wall plugs. 6. Using the two screws and wall plugs (all supplied ), attach the bracket to the wall. 7. Line up the side slot of the bracket and the alarm. Push the alarm onto the mounting bracket and turn it clockwise to fix it into place. Pull outward on the alarm to make sure it is securely attached to the mounting bracket. Trouble SingalPower / Alarm SingalTest / Reset Button Battery CompartmentSmoke alarms for minimum securityFigure 1:Location for placing CO alarm for A multi-floor Backplate Backplate
2 Device Enrollment The 6 digit serial number located on the back of the CO alarm housing must be enrolled into the alarm control panel with Installer programming. Refer to the receiver Installation Manual for details. Owners Instructions You should know about Carbon Monoxide Carbon monoxide, also known as "CO" by the chemical form, is considered to be a highly dangerous poisonous gas, because it is colorless, odorless or tasteless and very toxic. In general, biochemistry phenomena have shown that the presence of CO gas inhibits the blood's capacity to transport oxygen throughout the body, which can eventually lead to brain damage. In any enclosed space (home, office, recreational vehicle or boat) even a small accumulation of CO gas can be quite dangerous. Although many products of combustion can cause discomfort and adverse health effects, it is CO gas which presents the greatest threat to life. Carbon monoxide is produced by the incomplete combustion of fuels such as natural gas, propane, heating oil, kerosene, coal, charcoal, gasoline, or wood. The incomplete combustion of fuel can occur in any device which depends on burning for energy or heat such as furnaces, boilers, room heaters, hot water heaters, stoves, grills, and in any gasoline powered vehicle or engine (e.g. generator set, lawnmower). Tobacco smoke also adds CO to the air you breathe. When properly installed and maintained, your natural gas furnace and hot water heater do not pollute your air space with CO. Natural gas is known as a "clean burning" fuel because under correct operating conditions, the combustion products are water vapor and carbon dioxide (CO2), which is not toxic. The products of combustion are exhausted from furnaces and water heaters to the outside by means of a fuel duct or chimney. Correct operation of any burning equipment requires two key conditions: (a) An adequate supply of air for complete combustion. (b) Proper venting of the products of combustion from the furnace through the chimney, vent or duct to the outside. Typical carbon monoxide gas problems are summarized here: (a) Equipment problems, due to defects, poor maintenance, damaged and cracked heat exchangers. (b) Collapsed or blocked chimneys or flues, dislodged, disconnected or damaged vents (c) Downdraft in chimneys or flues. This can be caused by very long or circuitous flue runs, improper location of flue exhaust or wind conditions (d) Improper installation or operation of equipment, chimney or vents (e) Air tightness of house envelop/inadequate combustion of air (f) Inadequate exhaust of space heaters or appliances (g) Exhaust ventilation/fireplace competing for air supply. Potential sources of carbon monoxide in your home or office include clogged chimney, wood stove, wood or gas fireplace, automobile and garage, gas water heater, gas appliance, gas or kerosene heater, gas or oil furnace, and cigarette smoke. More information about conditions which result in transient CO situations 1.Excessive spillage or reverse venting of fuel burning appliances caused by (a.)Outdoor ambient conditions such as wind direction and or velocity , including high gusts of wind; heavy air in the vent pipes (cold humid air with extended periods between cycles) (b.)Negative pressure .differential resulting from the use of exhaust fans. (c.)Simultaneous operation of several fuel burning appliances competing for limited internal air. (d.)Vent pipe connection vibrating loose from clothes dryers, furnaces, or water heaters. (e.)Obstructions in or unconventional vent pipe designs which amplify the above situation. 2.Extended operation of unventilated fuel burning devices (range , oven,fireplace, etc) 3.Temperature inversions which can trap exhaust gases near the ground. 4. Car idling in an open or closed attached garage, or near a home Possible symptoms of Carbon Monoxide Poisoning Carbon monoxide is colorless, odorless, tasteless, and very toxic. When inhaled, it produces an effect known as chemical asphyxiation. Injury is due to the combining of CO with the available hemoglobin in the blood, lowering the oxygen-carrying capacity of the blood. In the presence of CO gas, the body is quickly affected by oxygen starvation. The following symptoms are related to CO poisoning and should be discussed with all members of the household so that you know what to look for: (a) Extreme exposure: unconsciousness, convulsions, cardio- respiratory failure, death (b) Medium exposure: severe throbbing headache, drowsiness, confusion, vomiting, fast heart rate (c) Mild exposure: slight headache, nausea, fatigue (similar to "flu-like" symptoms) Many victims of carbon monoxide poisoning indicate that while they were aware that they were ill , they became so disoriented and confused that they were unable to help themselves by either exiting the building or calling for a assistance. Young children and household pets may be the first affected. Exposure during sleep is particularly dangerous, because the victim usually does not awaken. Actions to take when CO alarm sounding ▲WARNING!! Actuation of your CO alarm indicates the presence of carbon monoxide ( CO) which can kill you. If alarm sounds : 1. Operate silence button 2. Call your emergency services or fire department or 911 3. Immediately move to the fresh air –outdoor or by an open door window. In case of harmful levels of CO gas being detected, your CO alarm M330 will go into a CO alarm mode as mentioned above. in “ CO Alarm Mode” Try to take the following necessary actions immediately: (a) If there is anyone experiencing the effects of carbon monoxide poisoning such as headache, dizziness, nausea or other flu-like symptoms, call your fire department right away or 911. You should evacuate all the people in the premises immediately. Do a head count to check that everybody is accounted for. (b) Do not re-enter the premises until the problem has been corrected and the CO gas has been dispersed out and a safe level is reached. (c) If no symptoms exist, Immediately ventilate the home by opening windows and doors. Turn off fuel burning appliances and call a qualified technician or your utility company to inspect and repair your problem before restarting appliances. Normally an activation of the CO alarm indicates the presence of CO gas. However, the CO gas can be extremely fatal, if it is not detected. The source of the CO gas may come from several possible situations, please refer to the list of sources of carbon monoxide in page 1. ▲CAUTION!! This CO alarm will only indicate the presence of CO gas at the sensor. However, you have to be aware that the CO gas may be present in other areas in the premises. Actions to take after the problem being corrected Once the problem about the CO gas presence in the premises has been corrected, the alarm of the CO alarm unit should be off. After waiting for 10 minutes, push the Test button to test the CO alarm unit so that you can make sure that it is working properly again. Test and silence your CO alarm Follow the test procedure described here or contact your CO alarm unit dealer or installer for testing instructions . DSC recommended that you test the entire alarm system at least one a week to verify the operation of all functions. The test/silence button is used to test if the CO alarm is working properly and to mute the unit during alarm. Test the unit Press the test button and you should hear 4 short beeps with a corresponding three LED flashes in 5 seconds , this cycle will repeat one more time. Familiarize yourself and your family members with this alarm pattern as this testing simulates a actual CO alarm condition. Silence the unit : If the CO alarm is sounding, pressing the test/silence button will have the alarm muted while at the same time red LED keeps flashing. After 4 minutes, if the CO concentration caused the alarm still remains at alerting condition, the CO alarm will reactivate. Owners Maintenance The CO alarm unit is designed to require minimum maintenance,
Download:
Mirror Download [FCC.gov]
Document ID1059659
Application IDhQOkLBup2TE6bBGGnfANOQ==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize18.04kB (225503 bits)
Date Submitted2009-01-21 00:00:00
Date Available2009-01-21 00:00:00
Creation Date2009-01-05 13:37:37
Producing SoftwareAcrobat Distiller 6.0 (Windows)
Document Lastmod2009-01-05 13:37:37
Document TitleMicrosoft Word - WS4913 User manual draft.doc
Document CreatorPScript5.dll Version 5.2
Document Author: panyi
FCC ID Filing: F5309WS4913

Navigation menu