UTC Fire and Security Americas 735-XMTR User Manual 8

UTC Fire & Security Americas Corporation, Inc. 8

1. 8
2. 8a

8

Download:
Mirror Download [FCC.gov]
Document ID	53896
Application ID	3vtdw82oCIL/0eBL1FVgyg==
Document Description	8
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	103.54kB (1294215 bits)
Date Submitted	1999-08-12 00:00:00
Date Available	1998-09-08 00:00:00
Creation Date	2001-05-30 09:38:52
Producing Software	Acrobat Distiller 4.0 for Windows
Document Lastmod	2001-05-30 09:38:53
Document Title	8

SimonllTM Security System
Installation Instructions
Document No. 466-1576
Revision Preliminary, April 10, 1998
Table of Contents
Special Installation Requirements 3
Requirements for UL-Listed Installations 3
Canada Listings (pending) 3
California State Fire Marshall Listing 3
Introduction 4
System Components 4
Planning Sensor Types & Locations 7
Planning Control Locations 10
Planning for Lamp, Appliance, Wallswitch,
and Universal/Garage Door Module Con-
trol 10
Setting the House Code and Unit Number 10
Planning System Access Codes 11
Utility Access Code 1 11
Utility Access Code 2 11
Master Access Code 1 1
Access Codes (1 - 5) 11
Duress Code 11
Planning System Options 12
Wiring the Control Panel 18
Connecting Hardwire Interior Sirens 18
Connecting a Hardwire Exterior Siren 19
Connecting Hardwire Sensors 19
Connecting the Universal/Garage Door
Opener Module 19
Connecting the Power Transformer 19
Connecting the Backup Battery 20
Connecting the Rechargeable Battery 20
Connecting the Phone Line to the Control
Panel 20
installing an RJ-31 X Jack 20
Programming Sensors 20
Connecting the Phone Line to the Control
Panel 21
Connecting the Audio Verification Module 21
Add words and picture to show installation of
AVMt 21
Programming Overview 22
Reset Memory to the Factory Deiaults 23
Programming the House Code and Unit
Numbers 24
Programming Light and Appliance Con-
trols 24
Programming Options 25
Option Programming 25
Programming System Access Codes 26
Installing the System 27
Control Panel 27
General Information 27
Control Panel Specifications 27
Installation Guidelines 27
Testing the Control Panel 28
Testing the System 29
Testing Sensors 29
It a Sensor Fails the Sensor Test 29
Testing Phone Communication 30
Testing Central Station Communication 30
Testing the X-10 Lamp Modules 30
Siren and X-10 Lamp Module Functions:
31
Notices 34
Special Installation Require-
ments
—
This security system can be used as a fire warning
system. an intrusion alarm system‘ an emergency no—
tiﬁcation system, or any combination of the three
Some installations may require certain conﬁgurations
dictated by city codes, state codes, or insurance re—
quirements. The following information indicates the
components of various listings.
Requirements for UL-Lisied Installa-
lions
This section describes the minimum system configu—
rations for UL-listed, Grade A (supervised) systems,
Basic System
All UL-listed systems requrre the following basic
components, The basic system does not require sen?
sins and can use the Remote Handheld Touchpad as a
controlling device.
0 Control Panel (60-693-95R)
- Class ll Line Carrier Power Transformer (22
091)
- 9-Volt, 1.2 Ah Lithium Backup Battery (34-037)
or a rechargeable 7.2Volt 1 Ah Nickel Metal
Hydryd Battery Pack
- Hardwire Siren (13—046) or Slimline Siren (60-
483—Ol)0r “Mouse" Siren (133,73)
Residential Burglary Alarm System Unit (UL
1023)
Basic system above. plus:
' Door/Window Sensor (60-670»95R) suitable for
installation on non-ferrous surfaces only
Residential Fire Alarm System Unit (UL 985)
Basic system above, plus:
' System Sensor Smoke Sensor (60-506-95)
Canada Listings (pending)
Residential Burglary Alarm System Unit
(ULC-5309)
Basic system as described for UL»listed installations.
plus:
' Door/Window Sensor (60-670-95R)
Note: The KeyChain Touchpad use-659 is UL Listed as a
miscellaneous signalling device and is for supplementary
use orlly.
CSA Certiﬁed Accessories
Residential Fire Warning System Control Unit
(ULC-SS45-M89)
Basic system as described for UL—listed installations,
plus:
- Wireless Smoke Sensor (60-506-95)
- SUPSYNC (Supervisory Synchronization) set to
2 (hours)
California State Fire Marshall Listing
The California State Fire Marshall listing is pending.
Introduction
This ITI Security System is easy to install if you plan
ahead and do everything in the following order.
1. Plan where to locate the hardwire sirens, sensors
and Control Panel. Use the tear out planning
sheets at back of this manual.
Wire the Class II transformer, hardwire sirens,
and phone,
3. Decide how the sensors, lights, and system
options will operate.
4. Program the sensors, lights and appliances, and
system options.
5. Install sensors and Lighting Modules.
6. Test system.
5°
Note: Program the sensors betore installing them because
the Control Panel and sensors must be In the same place
for programming. After you've programmed each sensor,
you can install them where you planned.
System Components
_————
The system can monitor up to 24 sensors using any
combination of the following sensors:
- Door/Window Sensor (60—670—95R)
- KeyChain Touchpad (60-659-95R)
- Remote Handheld Touchpad (6067 l—95R)
- Indoor Motion Sensor (60—639—95R)
' Outdoor Motion Sensor (60-639-95R—OD)
' ITI 319 5 Sensors (including Smoke Sensors)
You may use any of these modules:
' X- 10 Lamp Modules (13-403)
- X—lO Appliance Modules (13—402)
- X-lO Powerhorn/Remote Siren Modules (13-
398)
- X-lO Universal/Garage Door Modules (13-399)
- X—lO Wall Switch Modules (13—397)
Note: Use at the above X-10 modules has not been inves-
tigated by UL,
Figure 1. shows the Control Panel, control touchpads,
and some compatible sensors and modules.
mam.
rmnmn
memo
Figure 1. Typical Security System Components
Security System
The security system has three types of components:
the Control Panel‘ devices that report to the Control
Panel, and devices that respond to the Control Panel.
Control Panel
The Control Panel is the main processing unit for all
security functions. It receives signals from and re—
sponds to wireless sensors and Wireless touchpads
throughout the premises. The buttons operate the se—
curity system. When using the Control Panel with the
cover open, the buttons program the security system.
Door/Window Sensor
For intrusion protection, install Door/Window sen-
sors on all ground-ﬂoor doors and windows. At a min-
imum, install them in the following locations:
- All easily accessible exterior doors and windows.
- Interior doors leading into the garage.
- Doors to areas containing valuables such as cabi-
nets and closets.
KeyChain Touchpad
The KeyChain Touchpad enables you to turn the sys—
tem on and off before entering the home or to turn on
the siren and to call the central monitoring station if
there is an emergency. If you have Lamp Modules,
you can use the KeyChain Touchpad to turn all lights
on and off,
Remote Handheld Touchpad
The Remote Handheld Touchpad enables you to turn
the system on and off while in the home, turn lights
controlled by the system on and off (all or indivtdual
lights), or tum on a system siren and call the central
monitoring station if there is a non—medical emergen-
cy. The Remote Handheld Touchpad Will report an
alarm type speciﬁc to its sensor type (see Table 3 for
sensor and siren types),
2-Way Talking Touchpad
The 2»Way Talking Touchpad enables you to turn the
system on and off while in the home, turn lights con—
Irolled by the system on and off (all or individual
lights), or turn on a system siren and call the central
monitoring station if there is a non-medical emergen-
cyr The 2-Way Talking Touchpad will report an alarm
type specific to its sensor type (see Table 3 for sensor
and siren types). It annunciates status beeps and voice
feedback.
Indoor Motion Sensor
Indoor Motion Sensors are ideal Whenever it is not
practical to install Door/Window sensors on every
opening. Identify areas Where an intmder is likely to
walk. Large areas in an open ﬂoor plan, downstairs
family rooms, and hallways are candidates for Indoor
Motion Sensors. Indoor Motion Sensors are not suit-
able for rooms where pets can enter. Indoor motion
sensors can also be used to sound chimes, but cannot
be used for intrusion protection and as a chime sensor
simultaneously.
Outdoor Motion Sensor
Use Outdoor Motion Sensors to identify motion in a
protected outdoor area. Detected motion in this pro-
tected area can sound chimes or turn on outside lights
Do not use Outdoor Motion Sensors for intmsion pro-
tection.
Smoke Sensor
Smoke Sensors can provide fire alert protection by
causing the alarm to sound throughout the house. You
can add sensors near sleeping areas and other ﬂoors of
the house, Avoid attics, kitchens, above ﬁreplaces,
dusty locations, and areas with temperature extremes.
See the instructions packaged with the Smoke Sensor
for complete placement information.
Refer to the diagram on the next page for specific
placement of Smoke Sensors.
ITI TooIBox
The ITI ToolBox is a Windows®~based program that
saves you time by simplifying Control Panel pro
gramming Using only a PC, a modem, and a standard
telephone line, ToolBox makes creating new custom-
er accounts and updating the panel settings ofexisting
customers simple and quick. See the ITI ToolBox
manual and ToolBox's on-line help for instructions to
use ToolBox for programming this Control Panel,
The ITI ToolBox has not been investigated by UL and
should not be used on UL Listed Systems.
ITI CS-4000 Receiver
The CSA4OOO Receiveris used to monitor this security
system.
ITI HomeLink Transceiver (ll-IT)
The ITI HomeLink Transceiver is a radio transmitter}
receiver designed to receive signals from the Prince
Universal Transmitter (HomeLink®), then retransmit
the signals to a security system panel, allowing the
HomeLink® to control the arming, disarming, and
light functions of the security system, The IHT also
enables the user to control the garage door opener
from the HomeLink®
The ITI HomeLink Transceiver has not been investi-
gated by UL and should not be used on UL Listed
Systems,
SWIS
The Supervised Wireless Interior Siren annunciates
alarm appropriate sounds and because of its back—up
battery functions when the power is off,
C0 Alarm
The Learn Mode CO Alarm (#60-652-95) alerts users
to hazardous levels of carbon mono de gasl If dan—
gerous concentrations of gas are present, the CO
Alamfs red indicator light comes on , its internal si—
ren goes off, and it transmits an alarm to theControl
Panel The panel sounds its own alarm and calls the
central station.
Emergency Planning Floor Plan
Audio Veriﬁcation Module (AVM)
The AVM give the central station operator the ability
to hear what's happening at the premises during an
alarm and speak direclty to the system owner The op—
erator can them determine how serious an alann is,
ﬁnd out what kind of help is needed, and dispatch the
appropriate assistance.
Use the followmg guidelines when 7 A “m" Mum‘hwm
drawing an emergency planning ﬂoor Ewiwm 11 Beam” “9 ‘°“'"‘ M ”H" "M'-
plan for the homeowner: mm mm
Rm mm Bedroom E mm
- Show all building levels. A W"?
A Room Recreation
- Show exits from each room (2 a R
. Essa/"ant asemem um“
exits per room are recommended), ,
- Show the locations of all security a
Dining ‘ E“, , 5mm tlaclou lhoulﬂ
system components. kw,“ Kffne" "mm mm" he local"! bntwlln in-
. slleplnglr nndtneusl
- Show the locations of any lire :Vl"ﬂ FH' _ on". “My, "a um"
extinguishers, W" Balm“
Dining 5mm
Rum Kilmn in umiiy Ilvlnn unlts with mull
w '~ ill-n an. m plug lrel,lncllen
Room . smpuuninclorauacnaru.
Lit/mg
Room Bedroom
Eadvoom
Note. coiling-mount“ mick. u tlelor! should he lacuna in in. ccnur Dllhl lawn
nrnﬂll, or not ion than 4 menu mm in. w
wlun the detecior I: min-mud
on in. wall, the top elm. ﬂulecturshould ll. 4 in lz inelul mm in. ulllng.
NGYE: Dc rial inst-ll smoke aneczurswn-u nun-l Ilmhilnl (Imp-IIIIHQ! we no"
mo'F urbalow urr “50,110 ncllccill in mm In from ntAc N
"gist-u or olhnrlotlllons when normal all clvculltiun will li- psmnkc
”om ant-ring [nu dehctur.
note: Addlllnnalln'orml
um lrom.
n on household ﬁn wimlng ll "mum a: nominal
Tn. n-llumi rim Prel-cilcn Assueininn, Baﬂovymlrch Pan,
Quincy, MA uzzsv. quinlt snneaw No urn".
0 Requlr-d smuk- dttnclor
um dlteetov
v Ind an: man dolnclor is optional iiuoor is "at pruvidld hutwun
ins-mull mnucnaiicn moms,
mm.
Planning Sensor Types & Locations You’ll need to understand the application for each
sensor. For example. KeyChain Touchpads are typi-
cally programmed as sensor type 01 (Portable panic),
used to send an intmsion alarm to acentral monitoring
station. This sensor type is instant intrusion. it does
not require restoral or supervisory communication
with the Control Panel and it is active in all 4 arming
levels (disarm, arm doors & windows, arm motion
sensors, and aim doors/windows and motions sen-
sors).
The ﬁrst step to an easy and successful installation is
to decide what areas or items to protect which lights
or appliances to operate. and the best location for the
Control Panel. sensors or sirens, Use the previous in—
formation and Table 1, Device Location Planning, to
note your requirements.
Use Table 2 and Table 3 to determine the appropriate
Sensor Type for the sensors you will be adding.
Table 1 Sensor/Device Location Planning Table Locations In order as communicated by Control Panel
when changing sensors, except that Remote Locations are not used by the Control Panel, but only used here tor
plannlng purposes. (This table is duplicated at the end of this manual)
_ Sensor/Devlce Name 5
g (userabiezaTablea 0 g ‘_ E E E E g g
-. todeterminesensor a 8 - -. ° 5 3 a 8 ° LE 2
u >- ._l a g 3 , x 8 a a a: a .
2 typenumbﬂs) beagoéimm‘i‘ngog uzﬁséa
3 Theiollowmgare Eéséséﬁéigsséggcegggsg £2
exaMPlesoﬂiy- $éim5m6655553§856m£§l££ Di
~——|
KeyCllamTouchpmd 01 x J-
Door/Window 13 x
__
i l
10
11
t.
12 _—l
13 I'
14
15
16
._l
17 L
18
19
Table 1 Sensor/Device Location Planning Table Locations in order as communicaled by Control Panel
when changing sensors, except that Remote Locations are not used by lhe Control Panel, but only used here for
planning purposes. (This table is duplicated at the end of this manual)
Table 2 Recommended Sensor Types
4 Recommended
Device
Sensor Type
KeyChAin Touchpad OL 03, 06, 07
Remote Handheld Touch- 0], 03‘ 06, 07
pad and 2-Way Talking
Touchpad
indoor Morion Sensor 17 (intrusion), 25 (chime)
Outdoor Motion Sensor 25
Smoke Sensor 26
Exterior Door 10
Interior Door 14
Window Sensor 13
SWIS TB D
CO Alarm 29
Sensor/Bovine Name E
6 5 E
z (useTabIe_2&Table3 u s“ ‘5 E E E E E g E
5 lodeterminesensor g j 5 g a o if." g g Q E x 6 _ E
3 c T
g typenumbers) {Eaeugzﬁﬁﬁiggsu ya§2§m _
g Thelollowmgare g ggﬁsgg ggggggcg-agggg E3
examplesonly- ﬁéﬂé’éﬁé 3355320555‘55'555 62
20
2! I.
22 I
23
24 _._l __|_
Table 3 Sensor Type Characteristics (This table is duplicated at the end of this manual)
Q . . Siren Resto Su er Active in
l‘ g: Name/Applicahun Delay 1 . P
E Type ra vlsory Levels
Tmnnir» 24 houraud’El‘Ii e ixed emergency button l'ntrusion T o es
in Portable Panic 24 hour audible portable emergency buttons Intrusion I No No 1234
02 Fixed Fame 24 hour silent ﬁxed emergency bulmns Silent I No Yes 01234
03 Purtable Panir 24 hour silent portable emergency buttons Silent I No No 01234
04 Fixed auxlllary' 24 hour auxiliary sens-Ur, such as Pendant Panic Emergency I No Yes 01234
Fixed Auxiliary 24 hour emergency button Siren shut off con- Emergency
05 firms CS report I No Yes 01234
Portable Auxiliary. 24 hour portable auxiliary alert button Emergency 1 No No 01234
Portable Auxlllary’ 24 hour pcrlablc auxiliary button. Siren shut Emergency I N0 No 01234
oil confirms cs report I...
08 Special lnlmslon: such as gun cabinets and wall safes. Intrusion I Yes Yes 1234
09 Special Intrusion: such as gun cabinets and wall sales, Intrusion S Yes Yes 1234
10 Entry/Earn Delay: Enlry/Exit Delaythatrequirea standard delay Intrusion S Yes Yes 24
time. Chime
13 lnslanl perimeter, Exk'rinr doors and Windows, Chime Intrusion I Yes Yes 24
14 Instant lnlerior: Interior doors lntmsicn F Yes Yes 234
15 Instant Interior: Interior PIR motion sensors' L—lntrusion F No Yes 234
15 Instant Interior: Interior dnms Intrusion F Yes Yes 34
17 Instant interior PIR motion sensors“ Intrusion F No Yes 34
19 pelayed Interior, intenor doors that initiate a delay before going Intrusion 5 Yes Yes 34
into alarm-
20 Delayed lntenoriPlR motion sensors that initiate a delay belnre IntruSlon S No Yes 34
golng into alarrn
21 Local instant Interior: 24 hour local alarm zone protecting anyr Intrusion I Yes Yes 1234
thing that opens and closes. No Report
22 Local delayed interior: same as group 21, plps activation initiates lm-rusmn 5 Yes Yes 1234
a delay before going uito alarm, No report.
Local instant Auxiliary: 24 hour local alarm zone protecting any— Y
a 01234
23 Ihing that opens and closest No report Emergency I Yes 5
Local instant Auxiliary: 24 hour local alarm zone pmtecnng any- Ems, em
24 thing that opens and closes. Sirens shut off at reataral. Nu 3 y I Yes Yes 01234
report,’
25 Local Special Chime: Nauly the user when a door is opened, Two beeps I No Yes 01234
Sounds emit from a local armimmtor.‘ No report
26 Fuel 24 hour fire, rale—ul—rise heal, and smoke sensors§. Fire I Yes Yes 01234
27 Lamp cnnlml or other customer featuret No report Silent I Yes Yes 01234
28 FIR motion sensor, sound sensor, or pressure mint No report Silent I No Yes 01234
29 Auxiliary: freeze sensor Emergency I Yes Yes 01234
32 FIR motion sensor or sound sensor: No report Silent I No No 01234
”This type ls not certiﬁed as a primary protection Circuit for UL- Delays.
listed systems and is for supplementary use only. 1: “15mm Delay ("0 may immsdm mm)
§This type is requimd for ULeIitmd residential ﬁre alarm applied 5 = Standard Delay lalarni sounds alter programmed cnlry delay
lions. “mcl
F: Follower Delay (alarm sounds lmmsdlalely lienlry/cxu delay
is not active, otherwise alarm sounds alter programmed entry (Is-
The arming levels are. lay time)
{This type has not been invcsligaled by UL.
o = Suhdisarmod (used 10 bypasa sensors which are active 24 hrs/
day) Only (hi: Muster Access Code can enlcr lhis level
I = DlSIIrm
Arm Doors & WindoWs
, Arm Mol'lon Sensors
4 = Arm Dools/Windnws & Motion Sensors
Planning Control Locations
Control Panel
Locate the Control Panel so that the alarm sounds can
be heard and it will be convenient to operate. It must
be near an electrical outlet and telephone receptacle.
Remote Handheld Touchpad and Z-Wny Talking
Touchpad
Locate Remote Handheld Touchpads where they will
be convenient and offer quick response in emergenf
cies.
KeyChain Touchpad
KeyChain Touchpads attach to the owner’s key ring
or can be conveniently can-led,
Planning for Lamp, Appliance,
Wallswitch, and Universal/Garage
Door Module Control
As you program the modules, the Control Panel asks
you to choose the house code, unit number and acti-
vation method. Fill out Table 4, Home Control Plan-
ning Table, before you begin programming,
The system can control 8 individual unit numbers on
Lamp. Wallswitch. Appliance. and Universal/Garage
Door Modules.
Setting the House Code and Unit Num-
her
Each device controlled by the Control Panel must
have an identiﬁcation setting. The modules use two
dials to set identiﬁcation codes: one with letters A
through P and one with numbers I through 16.
The lettered dial sets the house code. The house code
enables the system to differentiate this home from
other homes in the area. Set all modules (except the
remote siren) and the Control Panel to the same house
code.
10
The numbered dial sets the unit number. The unit
number tells the system which device you want to
control. Each unit number should be different (unless
you want speciﬁc lights or appliances to be activated
together). The Control Panel recognizes up to 8 unit
numbers for sensoractivated, time—activated and en—
try/exit delay lights. When unit numbers 9—16 are
used for lamp modules, they can only be controlled by
an all on or all offcommand,
A lamp will ﬂash to the arming level ifits unit number
is set to 10. A lamp set to unit number 10 will ﬂash
once ifthe Control Panel is disarmed, twice if doors
& windows are armed, etc.
The remote siren can be set to any unit number to hear
alarm sounds. Set it to unit number 9 to hear arming
level beeps, status beeps, and trouble beeps.
To Fill Out the Lamp Control Planning Table:
Note: Do not use a lamp module to control appliances. use
an appliance module, since the wattage rating on Lamp
Modules is less than on Appliance Modules.
1. Set the house code on all the Modules, except the
remote siren to the same letter.
Set the Remote Siren house code to the next al-
phabetical letter. For example, if die house code
is B, set the remote siren’s house code to C.
Note: The house code instructions which come with the
Powerhoin Siren won't work with this Control Panel. Follow
Ihe instructions given here.
2. Set the Module unit numbers.
Note: If you are using a Universal Module to operate a ga—
rage door. make sure to assign a unique unit number to this
Module choosing from Hi.
3. List the location of the lamp or appliance in the
Location column of Table 4.
Write the location of each Lamp Module on an
adhesive note and label the module.
Decide if the device should be activated by sen-
sors, entry/exit delay, time, or a combination. An
example of sensor activation is using a motion
sensor to tum on a light. Record the information
in the appropriate columns.
Table 4 Home Control Planning Table (This table Is duplicated atthe end otihis manual)
Module Activated by Time Activated
Unil it Type Localion Sensor
Entry/Exit Start Tlme Stop Time
Example Lamp Hall lamp Motion
Yes 8 pm 1030 p.m.
Planning System Access Codes
Use the following to plan system Access Codes. Fill
out Table 5 to use when programming these codes
Utility Access Code 1
This access code is used during installation. The de—
fault utility access code is 4321. This code can be used
for all programming.
Utility Access Code 2
The default access code is 4321. This access code is
used for all programming except changing utility ac-
cess code 1 and changing options 4, 5, 6, 8. 9, 12, and
13.
Master Access Code
The default Master Access Code is 1234. This user
code is used to: disarm the Control Panel, disarm the
Control Panel to subdisarmed, program options 1
through 3. 36, 37, 41 - 43, program light control, set
the duress code, and perform a sensor or phone test,
Access Codes (1 - 5)
The Control Panel can have up to 5 secondary user ac-
cess codes. These could be used by children, a baby
sitler, or a service person. These codes have the same
programming privileges as the master access code ex»
cept they cannot program access codes 1 - 5 or the du-
ress code.
Duress Code
The Duress Code is able to disarm die panel, and send
a silent alarm to the Central Station.
Table 5 System Access Codes
Type Default $1717.15;
Uiiliiy Access Code 1 432i
Utility Access Codi: 2 4321
Master Access Code 1234
Access Code 1 None
Access Code 2 None
Access Code 3 None
the system clock, program access codes 175, program
11
Table 5 System Access Codes
T... w... on;
Access Code 4 None
Access Code 5 None
Duress Code None
Planning System Options
Use the following to plan system Options. See Table
11 for a complete listing of all system options and
their characteristics. Fill out the last column ofthis ta-
ble to use when programming.
Option 01: Panel Beeps
Add tums on panel beeps that sound when an access
code is entered or when the arming level is changed.
Delete turns off panel beeps.
Option 02: Panel Voice
Add enables the panel's voice.
Delete disables the panel's voice.
Note that the panel voice is always on for status mes-
sages, open Sensor responses. and when in program
mode.
Option 03: Latchkey (Reports as 99)
Add programs the Latchkey time. If Latchkey is en
abled, when the Control Panel is armed and the Con~
trol Panel is not disarmed by the preprogrammed
time, the Control Panel will call in a Latchkey alarm
at the programmed time.
Delete removes the Latchkey time. Latchkey cannot
be enabled when the Control Panel is armed.
Option 04: Primary Phone Number
Add programs the primary phone number to be called
when there is an alarm. The phone number will call
the central station.
Delete removes the primary phone number
12
Option 05: Secondary Phone Number
Add and Delete function the same as they do for the
primary phone number. This number can be to a nu—
men'c pager or a central station. When using it to call
a numeric pager. program this phone number with 2
pauses (press the test button to program a pause) at the
end of the number. Set Phone Mod 2 (option 13) to 8
or 9. The Control Panel will call a numeric pager
twice for each report. Pagers that require the Control
Panel to dial more than 22 digits will not work. Silent
alarms report to a pager as an intrusion alarm. See the
Owner‘s Manual for more reporting information.
Option 06: Downloader Phone Number
Programs the IT] ToolBox Downloader telephone
number.
Add and Delete function the same as they do for the
primary phone number.
Option 07: Account Number
Add programs the account number.
Delete resets it to 00-000.
Option 08: Phone Lock
Add enables phone lock.
Delete disables phone lock.
Option 09: DL Code (Downloader Code)
Add programs the downloader access code. The
Downloader Code is used during Control Panel pro
gramming with the ITI ToolBox. The Control Panel's
downloader code must match the downloader access
code in the ITI ToolBox account in order to program
the Control Panel using the ITI TooIBox.
Delete resets it to 12345.
Option 10: Entry Delay
Add programs the entry delay. Enter time in seconds.
The range is 005-120 seconds (3 digits must be en-
tered).
Delete sets the delay to 5 seconds.
For UL listed systems, the entry delay should not ex-
ceed 45 seconds.
Option 11: Exit Delay
Add programs the exit delay. Enter time in seconds.
The range is 005420 seconds (3 digits must be en-
tered).
Delete sets the delay to 5 seconds.
For UL listed systems, the em delay should not ex-
ceed 45 seconds.
Option 12: Phone Mod 1
Add sets the report content and format which the pri-
mary phone number uses. The range is 0—3.
Delete sets the phone mod to 0
Table 6 Phone Mod 1
Enter # Reports Format
_—'0_ All
1 All | 4/2
2 Alarms IT]
3 Aim", 4/2
Alarms include: Fire, Intnision, Emergency, and Si-
lent.
Non-Alarms include: Latchkey, No ActiVity, Alarm
Cancel. Opening, Closing. Force Armed, AC Power
Failure, CPU Low Battery, and Trouble Restorals.
All includes: Alarms and Non-Alarms.
UL has only veriﬁed compati ility with the [TI
CS4000 Digital Alarm Communicator Receiver.
Option 13: Phone Mod 2
Add sets the report content and format that the second—
any phone number uses. Range is 0-9.
Delete sets the phone mod to 0.
Table 7 Phone Mod 2
Enter 5 Reports F'”
ma!
0 All In
1 All 4/2
2 Alarms IT]
3 Alarms 4/2
4 Non-Alarms 1T]
5 Non-Alarms 4/2
6 Phi-me 1 failure Fri
7 Phone 1 failure 4/2
Latchkey/No Activity/
8 Phone Test P35“
Alarms/Latchkey/No
9 Activity/Phone Test Fag“
Option 14: DTMF Dialing
Add enables DTMF dialing.
Delete enables pulse dialing.
Option 15: No Activity (Upper Sensor 79)
Add enables the no activity time-out. Program the no
activity time-out in hours. The range is 02-24 hours (2
digits must be entered).
Delete disables the no activity time-out.
Option 16: Auto Phone Test (Upper Sensor 93)
Add enables the auto phone test. Program the auto
phone test frequency in days. The range is 00] ~ 254
days (3 digits must be entered).
Delete disables auto phone test.
Option 17: Dialer Delay
Add enables the dialer delay. Program the delay in
seconds, The range is 005-120 seconds (3 digits must
be entered).
Dale/e disables the dialer delay,
For UL installations, dialer delay time cannot be
greater than 45 seconds
Note‘ The Control Panel will not wait the programmed dial-
er delay to call ln an alarm it the Control Panel is disarmed
before the dialer delay expires and opening reports are on.
Both the alarm and opening reporl will be called in immedi-
13
ately.
Option 18: Alarm Cancel
Add enables alarm cancel. Program the time in min-
utes. [f the Control Panel is disamed from an alarm
state within the programmed time. the Control Panel
will send an alarm cancel message. The range is 01-
30 minutes (2 digits must be entered).
Delete disables the alarm cancel.
Option 19: Supervisory Time (SUPSYNC)
Add sets the supervisory time. Program the time in
hours. The range is 02—24 hours (2 digits must be en—
tered).
Delete resets SUPSYNC to 2 hours,
For UL listed systems, the SUPSYNC shall not ex~
ceed 4 hours.
Option 20: Manual Phone Test (Upper Sensor 83)
Ark] allows the user to perform a manual phone test.
Delete disables manual phone test.
Option 21: Opening Reports (Upper Sensor 84)
Add enables opening reports. Opening reports will be
sent to the central station if the Control Panel is dis—
armed from a higher arming level. Also, ifthe Control
Panel is armed to level 4 from level 2 or 3, an opening
report will be sent to the CS.
Delete disables opening reports.
Option 22: Closing Reports (Upper Sensor 85)
Add enables closing reports. Closing reports will be
sent to the central station if the Control Panel is armed
to level 2, 3, or 4.
Delete disables closing reports.
Option 23: Force Armed (Upper Sensor 87)
Add enables force armed report. A force armed report
will be sent to the central station.
Delete disables force armed reports.
Option 24: AC Power Failure (Upper Sensor 90)
Add enables AC power failure reports. An AC power
14
failure report will be sent to the central station if the
Control Panel has lost power for 15 minutes. The
Control Panel will report AC power restoral when
power returns to the Control Panel.
Delete disables AC power failure and restoral reports.
Option 25: CPU Low Battery (Upper Sensor 91)
Add enables CPU low battery reports. A low battery
report will be sent to the central station when the Con—
trol Panel's battery voltage drops below 7.65 volts.
Delete disables CPU low battery reports.
Option 26: Fail to Communicate
(Upper Sensor 96)
Add enables fail to communicate. If the Control Panel
is not able to connect to the CS when it's trying to re—
pon an alarm, the Control Panel will indicate this with
trouble beeps and in the status message.
Delete disables fail to communicate.
Option 27: Ring/Hang/Ring (Feature 01)
Add enables ring/hang/ring to use with ToolBox and
remote phone access. This feature is useful when pro—
gramming a Control Panel in a home with an answer-
ing machine. Program ring/hang/ring by number.
Table 8 Ring/HangIRing Program Numbers
Program # Control Panel will answer after:
1— ring/hang/ring or 10 rings
2 rmg/hungring/hanglring or 10 rings
3 rinyhanyring/hanyn'nyhanglring or 10
rings
4 10 rings
If ring/hang/rt'ng is programmed as:
Program # 1 -
1. Call the Control Panel and let the phone ring
twice then hang up.
2. Wait I0-40 seconds and call the Control Panel
again.
3. The Control Panel should answer on the first
ring.
Program # 2 » Repeat steps I & 2 before the Control
Panel will answer.
Program # 3 — Repeat steps I & 2 twice before the
Control Panel will answer,
Delete disables ring/hang/ring. The Control Panel
will not answer.
Option 28: No Delay from KeyChain Touchpad
(Feature 32)
Add arms with no entry delay when using the Key-
Chain Touchpad
Delete arms with an entry delay when using the Key-
Chain Touchpad.
Option 29: Control Panel Alarms
Add enables the Control Panel's piezo. Alarms will
sound from the Control Panel.
Delete disables the Control Panel’s piezo. Alarms will
not sound from the Control Panel.
For UL listed systems. at least one listed external au—
dible signal device shall be used if the external piezo
is disabled.
Option 30: Panic Alarms
Add enables panic alarms initiated from the Control
Panel or Handheld Touchpad.
Delete disables panic alarms.
Option 3]: Day of Week
Add will program the day of week based on a pro»
grammed number. The day of week will be used dur»
ing an event buffer dump to ToolBox.
Delete sets day of week to 0.
Table 9 Day of Week by Number
0 Sunday
1 Monday
2 Tuesday
3 Wednesday
4 Thursday
Option 32: 300 Baud
Add enables 300 baud communication Enable this
option for faster communication
Deletey enables l l() baud communications
Option 33: 2-Way Voice
Add enables 2-way voice communications between
the security system site and a monitoring station.
Delete disables Z-way voice.
Option 34: Fail to Open
Add enables fail to open. if the panel has not been dis-
armed by the programmed opening time, the panel
will call in a fail to open alarm to the Central Station
and/or a pager (Option 43).
Dele/r disables fail to open.
Option 35: Fail to Close
Add enables fail to close. If the panel has not been
armed by the programmed opening time, the panel
will call in a fail to close alarm to the Central Station
and/or a pager (Option 43).
Delete disables fail to close.
Option 36: Motion Activated Light Lockout Start
Time
Add enables motion activated light lockoout start
time. The panel will not turn on a light between the
programmed start time (option 36) and the pro-
grammed stop time (option 37) which is activated by
a sensor learned as type 25, even if sensor activated
lights are on. Both options must be programmed
for this option to work correctly.
Delete disables motion activated light lockout start
time. The panel will turn on a light activated by a sen-
sor learned as type 25 at all times, if sensor activated
lights are on.
Option 37: Motion Activated Light Lockout Stop
Time
Add enables motion activated light lockout stop time.
The panel will not turn on a light between the pro—
grammed start time (option 36) and the programmed
stop time (option 37) which is activated by a sensor
15
Ieamed as type 25, even it sensor activated lights are
on. Both options must be programmed for this up-
tion to work correctly.
Delete disables motion activated light lockout stop
time.
Option 38: Auto Arm
Add enables auto arm. Any sensor that requires resto-
ral and is open when the panel is armed will automat-
ically be bypassed when the panel is done protecting
The panel will protest for 4 minutes, then auto arm.
Pressing the ARM Doors & Windows button a second
time will stop the control panel protest and auto arm
the system. Pressmg this button a third time will arm
with no entry delay. The panel will go into alarm ifan
instant alarm sensor is opened during an exit delay. A
sensor learned as type 26 can never be bypassed
Delete disables auto arm. Any sensor that requires
restoral and is open when the exit delay expires will
automatically be bypassed. Protest beeps indicating
the arming level will sound 3 times from the X40
module. interior siren. and the panel siren. The panel
will go into alarm if an instant alarm sensor is opened
during an exit delay, A sensor learned as type 26 can
never be bypassed.
Option 39: Siren Time Out
Add programs siren time out from ] to 30 minutes.
The default siren time out is 4 minutes.
Delete disables siren time out.
Option 40: Trouble Beeps
Add enables trouble beeps.
Delete disables trouble beeps, so that if a problem oc—
curs the control panel will not notify the owner.
Option 41: Chime Voice
Add enables chime voice. The panel will announce
which chime sensor has been tripped if the chime fea-
tule is on.
Delete disables chime voice, The panel Will not an-
nounce which chime sensor has been tripped if the
chime feature is off.
16
Option 42: Speaker Level
Add sets speaker level to the high voice level.
Delete sets the speaker level to the low voice level.
Option 43: Pager Phone Number
Add enables pager phone number. Program the pager
phone number. The phone number can only call a
pager.
Delete disables pager phone number. The phone num-
ber will not be called in an alarm situation.
Option 44: Pager Phone Mod 3
Add enables pager phone mod 3 which sets the report
content and format which the pager phone number us-
es. Use the following table to determine the value to
enter.
Table 10:
En’t'er Reports
3 Latchkey, No Activity & Phone Test
__———————
9 Alarms. Latchkcy, No Activ y. Phone
Tcst, Openings. Closings, Fail to
Open/Close
Delete sets page phone mod to 8.
Option 45: Sensor Alarm Resmral
Add enables sensor alarm restoral. This sends a report
to the central station when a restoral sensor that is in
alarm is restored.
Delete disables sensor alarm restoral reports,
Table 11 Programmable Options (This table is dupllcatad at me and oi thls manual)
Who Can Change:
ui - Uliliry
Upper
Access Code 1:
"gm, 223.1” Funcﬂon Del-u]! Rnngt A uz - Urlllry' 22533;
Number ccess Code 2, M
~ Must-r: A -
Actess codes
01 Panel Beeps On On/Olf U1 U2 M A
02 Panel Voice On On/Ofi U1 U2 M A
03 Repuns as Lalchkey Option on 12:00 n.m. U1 U2 M A
99 — 11:59
pm.
04 Primary Phone Number Nnnc ”I 22 digits U!
05 Secondary Phone Number None 22 digits U1
06 Dov/"loader Phone Number None 22 digiit U]
07 Accounr Number 00000 00000 U1 U2
99999
_.____4
08 Phone Lock Oil On/Off U1
(79 Dcwnloiulcr Code 12345 00006 U1
99999
10 Entry Delay 30 sec 0057120 U1 U2
sec
11 Exll. Delay 30 sec 005-120 U1 U2
sec _J
12 Phone Mod 1 0 03 U]
13 Phone Mod 2 0 0—9 U1
1-..
14 DTMF On On/Oﬂ' U1 U2
15 79 No Activity Off 02-24 hrs U1 U2
16 93 Auto Phone Test Opliun (Must be emibled for 011 001-254 U1 U2
UL Listed systems) days
17 Dialer Delay Off 0017120 U1 U2
sec
18 Alarm Cancel Oi'l' 01-30 mm U1 U2
19 Supervisory T1mciSUPSYNCl 12 hrs 02-24 hrs U1 U2
20 83 Manual Phone Test On On/Off U1 U2
21 34 Opening Reports Off On/Off U1 U2
22 35 Closing Repons 011 On/Off U1 U2
23 87 Forced Arm Off 0n/Oﬂ' U1 U2
2/4 90 AC Power Failure (Must be enabled for UL Off On/Oi'f U1 U2
Listed systemsj
25 91 CPU LAJW Bauery (Must be enabled for UL On On/Off U1 U2
1.15mi syslems)
17
Table 11 Programmable Options (This table is duplicated at me end of this manual)
wmucsrb (£1;er
"W" Anus-s Ends 1;
“M a $25.5 Funnilon D‘luult Rang. “fizz-£3??? n g‘e‘m'g';
Access a“
26 96 Fail to Communicate (Must be enabled [OI UL On On/Off U1 U2
Listed systems)
27 Fcalure 01 RinyHang/Ring on 1.4 U1 U2
28 chtun: 32 Nu DclJy from KDyClmin Tuuchpzld Off On/Off U1 U2
29 High Level Siren On On/Off U1 U2
30 Punic Alarms On Oil/Off Ul U2
31 Day of Week 0 06 U1 U2
32 300 Baud Central Station Communications Off Oil/Off U1 U2
35 2»Way VOICE 0” On/Off U1 U2
34 Fill] 10 Open Off IZOOAM - U1 U2
1 1:59 PM
35 Fail In Close _—J Off 12:00AM? U1 U2
1 1.59 PM
36 MOKIQH AC‘IValed nghl Lockout Smn Time 0” 12:00 AM - U1 U2 M A
1 1:59 PM
37 Morin“ Activated Light Lockout Slop Time Off 12:00 AM - U1 U2 M A
1 1:59 PM
38 Auto Arm Off Uri/Off U1 U2
39 Siren Time Out Oil 01 , 30 U1 U2
Minules
40 Trouble Beeps Off On/Off U1 U2
4] Chime Voice Off OH/Off U1 U2
42 Speaker Level Off On/Off U1 U2 M A
43 Pager PhOHC Number Off 22 digits U1 U2 M A
44 Pager Phone Mod 3 8 S or 9 U1 U2 M A
45 Sensor Alztmi RESlel Olf Oil/Off Ul U2
Wiring the Control Panel
This section describes how to:
' connect hardwire interior and exterior sirens (if
being installed)
' connect hardwire sensors
- connect the power transformer
~ connect the backup battery
18
Connecting Hardwire Interior Sirens
The following lTl sirens may be used with this Con»
trol Panel:
- Slimline Siren (6048301)
- LDlOS Siren (13-374)
Follow the siren installation instructions included
with the siren to connect a hardwrre interior siren to
the Control Panel.
Connecting a Hardwire Exterior Siren
Use only the model 13~046 Hardwire Exterior Siren
as shown in Figure 2.
H‘nomhi wwvslsnm
Ali mm x» mm
mm mun:
mm. m...
mu mm- mm
D. and a
sum mm mm
nn-n— n. mum-m
Figure 2. Exterior Siren Control Panel Connections
Connecting Hardwire Sensors
This section shows how to wire hardwire sensors to
the Control Panel. For more detailed information on
installing hardwire devices, see the installation in-
structions that accompany each device. Wire sensors
to be supervised by using a 47k Ohm resistor (includ-
ed with the Control Panel).
Hmnwras Inputs/sins"
Namwue Hardwile
inwlt Hardwim inwz
a: m a
5mm Puwar mm-
Siren Common siren
©®®
Normally Normally
mom Closed
All inputs are power-
limited Circuits
Figure 3. ere Hardwira Sensors Normally Closed
Connecting the Universal/Garage
Door Opener Module
Use the following to connect a universal module to be
used to open a garage door:
1. Set the unit code of the universal module to a
unique unit number between I and 8.
2. Set the house code to the house code for the
installation.
3. Set the module’s switches to momentary and
relay only,
4. Connect the terminals on the universal mod-
ule to the button terminals on the garage door
opener.
5. Plug the universal module into a wall outlet,
Note: See the Programming Light and Appliance Controls
section to program a KeyChain Touchpad to open a garage
doon
Connecting the Power Transformer
Connect the power transformer as shown in Figure 4.
Plug the transformer into an unswitched outlet.
19
A“ Ls mumnewuvwnsu
inpu “pm".
Mammy»
llmnm mm Hamm-
lnpull Wu mm 2
A: music
£969
Fﬁ
bust it Portia
mum-wen
my no man.
Figure 4. Power Transformer Control Panel Con-
nections
Connecting the Backup Battery
Connect a 9-Volt lithium battery (ITI #34~037) to the
battery clips (see Figure 5.).
g you BAl’TERY
Figure 5. Control Panel Battery Installation
Note: The Control Panel Wll initially indicate a low battery by
lighting the SYSTEM STATUS button. If this button is
pressed the Control Panel will announce. System law bal-
tery.
The Control Panel does a battery test every 4 hours
and will clear the status message ifthe battery is good,
Perform a sensor test, see the Testing Sensors section,
to perform an immediate battery test.
Connecting the Rechargeable Battery
——
Add words and picture to show
this installation.
20
Connecting the Phone Line to the
Control Panel
If the system will be monitored by a central monitor-
ing station, you must install an RJ-3lXjack between
the telephone company (TELCO) block and the Con-
trol Panel. Thejack must be located within 5 feet of
the Control Panel.
Installing an RJ-31X Jack
Install and wire the RJ-31Xjack as shown in Figure 6.
£5???“ EM]
at now
0 O
O O
a... as»
molvEuﬂw
muss: WE an:
ac am
00 um
mm»;
m m
m m
H mu.”
Figure 6. RJ-SIX ering Dlagram
Programming Sensors
These instructions show you how to program sensors,
touchpads and other system devices into the Control
Panel
Connecting the Phone Line to the Con-
trol Panel
ll Plug one end of the phone cord (included with
the Control Panel) into the RJ-31Xjack,
2. Plug the other end of the phone cord into the
Control Panel phone jack.
When looking at the back of the Control Panel.
the [op block is used to connect the phone to the
Control Panel and the bottom block is used to
connect the Control Panel to the wall phone jack.
1“
Connecting the Audio Veriﬁcation
Module
Add words and picture to show installa-
tion of AVM.
21
Programming Overview
Programming Overview
—
. . To get you started:
These instructions tell you how to set up for program-
ming and to put the Control Panel in program mode. l' Press Add or D919” from the Start Menu,
2. Press Option #, Sensor/Remote, Access Code
1, Arrange the sensors, modules, Control Panel, or Light Control from the Main Menu,
and user controls on a table. .
2_ Open the Control Panel cover The system response at this point depends upon what
3, Enter Utility Access Code 1 (default is 4321) button youjustpressedt FOHUW the VOlCE prompts and
using red numbered keysr programming arrows to continue,
The default for utility access codes 1 and 2 is 4321. Program the Control Panel in this order:
The default master access code is 1234. 1" Sensors
4 2. House Code
You are now in program mode. 3} Light & Appliance Control
Programming is easy if you understand the ﬂow from ' Entry/Exit activated lights
left to right when using the programming butlons, ' Sensor ﬂCllVﬂted llghls
Follow the programming arrows or use the ﬂow dia» ' Time activated lights
grams to the right of the programming buttons. The 4- 013110“S
Control Panel will voice prompt you through pro- 54 Access Codes
gramming,
A Figure Control Panel Pro-
P R 0 G n A M M | N G L ImlmctlonSumm-ry é gramming Decal and
«new a Light, Clock, Access Code,
am" mu.-
. MWWMM mil Wm Sensor or Phone Test Decal
m ....5..°5’..o We need new logos.
WWW m
w an 46.7030 mum-"no,”
m“ AMIMWU’R
“$3.1th m-oé-i'O-rO-f'
Mao-{go “mp y" “in.“
w _o-»o-v
“mm“, m : r: 93
“arenas m 99:0
“melee-“er “a?“ .. ._ .,.
m—omo-oQ-vQ-vo Mao-203930
Winners-tn Delete a—
“mm“ m m w: mm.mmw-ommmm
% 5. 51, as; mmﬁBJWWWW
on»! u-
.,w.....m..m.m..m o
a,- mini mm. sums m r
nmnnm
3mm w Pnnrn T-t
mummy-HO M,
m "Wm
Ibis
Mdﬂlwywpmuwtyuml
mmlmunmlw
22
Reset Memory to the Factory Defaults want to add. The order of names the Control
Panel uses are: keychain remote. touchpad
remote, from door, back door, garage door, bed—
room, guest room, child's room, utility room, liv-
ing room, dining room, bathroom‘ laundry room,
kitchen, office, den, garage, special chime, base—
If it becomes necessary to set a_l| programming back
to the factory defaults, do the following.
1‘ Open [he Control Panel cover, merit. upstairs. downstairs, hallway, medicine
2' Simultaneously press Cancel, CIOCk S9" and cabinet, closet, attic, Each name may be used
Mtnutes and unplug the transformer. more than once.
NOTE. It Phone Lock is on, options 04.05.06, 08, 09. 3
12, and13will not reset to their delaults. Press DONE Whe“ yo“ he” the name yo“ W‘s“
to add.
Program sensors and devices before you install them, >
Note: When adding sensors, if you wish to use a more do-
Ths Control Panel recognizes a sensor when you scriptive location you may press the option button to use the
press the 53‘150’ 5 program button or mmPer SW‘mh- compass directions (north, north east, east, south east,
. . h. h , , rth t .
Table 12 describes the programming button location so“ sout we“ west no was)
for each device, 4, Enter the 2 digit sensor type using Table I.
Table 12 Device Program Buttons mm the red numbered keysi
Note: It you wish to use a sensor number other than the
Device Program Button Locatlon next available, enter a 2 digit sensor number with the red
Door/Window Sensor On mp of 50mm (cover numbered keys immediately after entering the sensor type,
removed)
5. Press the sensor’s program button or tamper
MONO" 58mm 0" back of WW“ (mﬂuming button. Open the switch of hardwired sensors,
mm ”mm/m) The Control Panel verbally confirms your pro-
KeyCham Touchpud Lock & Unlock hurrnns gramming,
Remote Handheld Touch- EMERGENCY buttons {to be
pad And 2-Way Voice used for non-medical emergen— To delete sensors:
Touchpad HES) l. Press Delete from the Start menu,
Hardwirc Sensors See individual sensor immiia. 2- Press Sensor/Remote mm the Mam men“ “HUI
non instructions you hear the name you want to delete
3. Press DONE. The system conﬁrms the item you
Note: When installing crystal and SAW sensors. use the in- removed.
stallation instructions included in their packing boxes
The Control Panel uses an ascending numbering se—
quence (beginning with 1) when adding (learning)
sensors. You may override the system suggested sen»
sor number by using the red numbered keys,
Use Table 1, which was ﬁlled out during the system
planning, to help program sensors.
To add a hardwire or RF sensor or remote control:
1. Press Add from the Stan menu.
2. Press the Sensor/Remote button from the Main
menu until you hear the room name or item you
23
Programming the House Code and
Unit Numbers
Lamp Modules, Appliance Modules, and Remote Si-
rens use the existing electrical wiring in the home to
receive signals from the Control Panel. Since there
are no direct wire connections required. any number
of modules can be plugged into available outlets and
installed in the system. All Lamp Modules and Appli-
ance Modules have a common house code that allows
modules to be identified by eight different control ad-
dresses.
The house code allows adjacent homes that have a
common power source to coeexist. The available
house code choices are from A to 0.
To program the house code:
1. Press Add from the Stan menu.
2, Press Light Control from the Main menu until
you hear the house code letter you want.
Press DONE.
4. Set the house code on each lamp and appli-
ance module using a screwdriver,
5. Set house code on the remote siren to the next
alphabetical letter greater than the house code.
P“
All Lamp Modules with the same house code will turn
on or ﬂash as a group on alarm or when operating the
“Light" button on a KeyChain Touchpod. The units
must be identiﬁed with a unique unit number, from 1-
8, to individually operate lights and appliances from a
Remote Handheld Touchpad or to selectively pro-
gram lights to go on during the entry/exit delay, to be
operated by a sensor or at scheduled times.
To assign a unit number:
I. See Table 4 for your planning information.
2. Set the Unit number switch on each module.
Programming Light and Appliance
Controls
_—
Use Table 4, which was ﬁlled out during the system
planning, to help program control modules.
To add an entry/exit activated light:
1.
2,
3.
Press Add from the Start menu.
Press Light Control from the Main menu.
Press Unit it until you hear the number you chose
on the module.
Press Entry/Exit Delay from the Control menu.
The Control Panel confirms your programming,
To add a sensor-activated light:
1.
2.
3.
Press Add from the Start menu
Press Light Control from the Main menu.
Press Unit it until you hear the number you chose
on the module.
Press Sensors from the Control menu until you
hear the sensor you want to control the light.
Press DONE. The Control Panel confirms your
programming.
Note: A KeyChatn Touchpad can be programmed to a unit
number. Press the star button to activate a light or open/
close a garage door using the Universal Module.
To add a time-activated light:
1.
2.
3.
u.
Press Add from the Stan menu.
Press Light Control from the Main menu.
Press Unit it until you hear the unit number you
chose on the module.
Press Time from the Control menu.
Press Hours and Minutes to set the beginning of
the schedule.
Press DONE.
Press Hours and Minutes to set the end of the
schedule.
Press DONE. The system conﬁrms your pro
gramming.
To delete an Entry/Exit-activated light:
1.
2.
3.
Press Delete from the Start menu.
Press Light Control from the Main menu.
Press Unit it until you hear the unit number you
want to delete.
Press Entry/Exit Delay. The system conﬁrms
your programming.
To delete a sensor-activated light:
I.
2.
3.
Press Delete from the Start menu.
Press Light Control from the Main menu.
Press Unit it until you hear the unit number you
want to delete.
Press Sensors from the control menu until you
hear the one you want to delete.
5. Press DONE. The system conﬁrms your pro—
gramming.
To delete a time-activated light:
1. Press Delete from the Start menu.
2. Press Light Control from the Main menu.
3. Press Unitit until you hear the unit number you
want to delete.
4. Press Time from the control menu.
Programming Options
Use Table 11, which was ﬁlled out during the system
plunning, to help program options.
Option Programming
——
There are two ways to enter options. They are as fol-
lows:
- Press Add and press the Option # hutton until
you hear the option to be changed.
OF-
- Press Add and enter the option number you
want to program with the red numbered keys.
The following instructions use the second method.
To set system options 01 and 02:
1. Press Add from the Stan menu.
2. Press Option it and 01 or 02 with the red num-
bered keys.
3. Press DONE.
To set system option 03:
1. Press Add from the Start menu.
2. Press Option it 03.
3. Press Hours and Minutes to set the time.
4. Press DONE.
To set system options 04, 05, and 06:
1. Press Add from the Start menu.
2. Press Option 5? and 04, 05, or 06.
3. Enter a phone number with the red numbered
keys. Press Test to enter a pause in the phone
number.
Note: The phone number is automatically stored after
you’ve pressed 22 digits. You will not have to press DONE
to store the number. it the number is less than 22 digits.
then DONE must be pressed.
To set system option 07:
Press Add from the Start menu.
Press Option # 07.
Enter the account number.
Press DONE.
eves»—
To set system option 08:
I. Press Add from the Start menu.
2. Press Option # 08.
3. Press DONE.
To set system options 09:
1. Press Add from the Start menu.
2. Press Option it 09.
3, Enter the downloader code.
4. Press DONE.
To set system options 10 & 11:
1. Press Add from the Start menu.
2. Press Option # 10 or 11.
3. Enter the delay times in seconds (3 digits must
be entered).
To set system options 12 & 13:
1. Press Add from the Start menu.
2. Press Option it and 12 or 13.
3. Enter phone mod number.
To set system option 14:
1. Press Add from the Start menu.
2. Press Option # 14.
3. Press DONE.
To set system option 15 (Upper Sensor 79):
1. Press Add from the Start menu.
2. Press Option # 15.
3. Enter the no activity time out (2 digits must be
entered).
To set system option 16 (Upper Sensor 93):
1. Press Add from the Start menu,
2. Press Option it 16.
3. Enter the number of days between each auto
phone test (3 digits must be entered).
25
To set system option 17:
I Press Add from the Start menu.
2. Press Option # 17.
3. Enter the dialer delay in seconds (3 digits must
be entered).
To set system option 18:
l. Press Add from the Start menu.
2. Press Option it 18.
3. Enter the alarm cancel time In minutes (2 dig-
its must be entered}.
To set system option 19:
1. Press Add from the Start menu.
2. Press Option 819.
3. Enter the supervisory time in hours (2 digits
must be entered).
To set system options 20 » 26, 28 - 30, and 32:
1. Press Add from the Start menu.
2. Press Option it XX.
3. Press DONE.
To set system option 27:
1. Press Add from the Start menu.
2. Press Option it 27.
3. Enter the ring/hanglring number.
To set system option 31:
1. Press Add from the Start menu.
2. Press Option # 31.
3. Enter the day of week number.
To set system option 33, 38, 40-42:
1. Press Add from the Start menu.
2. Press Option it XX.
3. Press DONE.
To set system option 34-37:
1. Press Add from the Start menu.
2. Press Option # 34.
3. Enter the start and stop times pressing HRS and/
or MIN buttons until the desired time is spoken.
To set system option 39:
1. Press Add from the Start menu.
2. Press Option it 39.
3. Enter the minutes (2 digits must be entered).
26
To set system option 43:
1. Press Add from the Start menu.
2. Press Option # XX.
3. Enter the phone number with the red numbered
keys. Press Sensor Test to enter a pause in the
phone number.
Mole: The phone number is automatically stored after
you've pressed 22 digits. You will not have to press DONE
to store the number. It the number is less than 22 digits,
then DONE must be pressed.
To set system option 44:
1. Press Add from the Stan menu.
2. Press Option it 44.
3. Enter phone mod number.
To set system option 45:
1. Press Add from the Stan menu.
2. Press Option it 45.
3. Press DONE.
To delete options:
1. Press Delete from the Stan menu.
2. Press Option from the Main menu until you hear
the name you want to delete.
3. Press DONE. The system conﬁrms the item you
removed.
Programming System Access Codes
——
Use Table 5, which was ﬁlled out during the system
planning. to program system Access Codes.
To add a code:
1. Press Add from the Start menu.
2. Enter the access code as prompted by the panel
voice by using the red numbered keys.
3. Press the Add button.
4. Press the Access Code button. Continue pressing
the Access Code button until you hear the access
code to be changed.
5. Press DONE.
6. Enter the new access code by using the red
numbered keys.
The Control Panel says. code name is XXXX (the new
4 digit access code).
To delete a code:
1. Press Delete from the Start menu.
2, Press the Access Code button. Continue pressing
the Access Code butlon until you hear the access
code to be deleted
3. Press DONE.
The Control Panel says, code name is deleted.
Installing the System
Control Panel
General Information
Do not install the Control Panel near a window or
door where it can be reached easily by an intruder.
Control Panels should be installed in locations where
they are most likely to be heard.
Metal objects, mirrors, and metallic wallpaper can
block signals sent by the wireless sensors, Make sure
there are no metal objects in the way when installing
the system
The system will prompt you through programming
steps with beeps and voice messages. If you need
more time before proceeding simply close the Con—
trol Panel cover until you are ready to continue.
When the cover is closed, the Control Panel is in the
operating mode, Each time you close the Control Pan-
el cover, a series of beeps will indicate the system sta-
tus:
- One beep indicates the system is disarmed
~ Two beeps verify that Door/Window sensors are
armed.
- Three beeps verify that Motion Sensors are
armed.
0 Four beeps verify that both Door/Window and
Motion sensors are armed.
Table 13: Arming Levels
Armlng Description ol Level
Level
0 Bypasses 24 hour intrusion season (Master
Access Code Only)
1 Disarm the system
2 Ann Doors and Windows
3 Arm Motions
4 Arm Doors‘ Window» and Motions
The system cannot work without power. If the electri—
cal power fails and the Control Panel battery is weak
or dead, the system Will not work
Control Panel Speciﬁcations
Power Requirements: 9 VAC, 700 mA
Backup Battery: 9 VDC 12 AH UltraLife Lithium
(The battery will last 24 hours with no AC if fully
charged.) ADD INFORMATION ON RECHARGE—
ABLE BATTERY.
Radio Frequency: 319.5 MHz + or - 140 kHz
Nominal Range: 500 feet, open—air receiving range
Operating Temperature Range: 32°»122 “ F (0°-
50“ C)
Maximum Humidity: 85% relative humidity, non—
condensing
Auxiliary Power Output: Regulated & unregulated,
fused 12 VDC at 250 mA (maximum)
Installation Guidelines
Use the following procedure to mount the Control
Panel to the wall or wall studs, using the supplied
mounting hardware and the panel mounting holes.
Materials Needed
~ Pencil
- Ham mer
- Screwdriver
28
To mount the panel:
10.
Choose a spot within a few feet of an electrical
outlet (the outlet should not be controlled by a
wall switch) and also within reach ofa telephone
Jack. The Control Panel can be placed on a desk,
tabletop. or it can be wall mounted.
Open the Control Panel cover and position on the
wall.
Mark the screw hole locations with a pencil.
Start holes with the tip of the screwdriver or a
nail,
Tap the wall anchors provided into the holes,
Insert the screws and partially tighten with the
screwdriver.
Hang the Control Panel on the screws and tighten
securely.
Remove the center screw from the outlet cover
plate,
Position the lmnsformer so that its screw hole is
aligned with the screw hole on the outlet cover
plate. Then plug the transformer into the outlet,
Replace the screw, and use it to secure the trans-
former to the outlet cover plate. Tighten the
screw firmly with your screwdriver.
Testing the Control Panel
Test the Control Panel by pressing the buttons as de-
scribed below:
ARM Doors & Windows-The Control Panel
arms Doors & Windows. Press twice to eliminate
the preprogrammed entry delay, The button will
blink when No Entry Delay is on.
ARM Motion Sensors-The Control Panel will
arm Motion Sensors. Press twice to turn Latch-
key on. The button blinks when Latchkey is on.
DISARM »The Control Panel will disarm Doors.
Windows. and Motion Sensors when also enter»
ing the appropriate access code.
SYSTEM STATUS-Press to determine system
status and system time.
CHIME Doors—Press to enable Control Panel
beeps which will sound when a protected door or
window, that is programmed as sensor type 10 or
13, is opened,
CHIME Special Motion- Press to enable Control
Panel beeps which will sound when a Motion
Sensor, that is programmed as sensor type 25, is
activated.
LIGHTS Time Activated-Press to enable system
controlled lights to turn on/off at a scheduled
time,
LIGHTS Sensor Activated—Press to enable sys-
tem controlled lights to turn on for4 minutes
when a speciﬁc sensor is tripped.
EMERGENCY-Press and hold or press twice
quickly to activate a non-medical emergency
alarm.
W~_,__.__ v 4,
Testing the System
—
This section describes how to perform the following
test procedure. .
- Testing sensors
' Testing phone communication
- Testing central station communications
Testing the X-10 Lamp Modules
You should test the system after installing, after ser»
vicing, and after adding or removing devices from the
system.
Testing Sensors
We recommend that you test the sensors after all pro-
gramming is completed and Whenever a sensor—relat—
ed problem occurs.
Note' While the sensor test rs a valuable installation and
service tool. it only tests sensor operation for the current
conditions. You should perform a sensor test alter any
change in envtronment, equipment. or programming.
1. Place all sensors in their secured (non-alarm)
state,
2. Open the Control Panel cover.
3. Enter the appropriate access code.
4. Press Test.
The Control Panel responds with Sensor ten, pres:
again to change or DONE to select.
5. Press DONE.
Note: lithe primary or secondary phone number (option 4
or 5) has been programmed, after pressing Test a second
time, the Control Panel announces Phone Test. The phone
testing procedure Will be discussed later in this manual, If
the DL phone number (option 6) has been programmed, air
ter pressing Test a third time. the Control Panel announces
DL phone test.
The Control Panel will prompt you to trip each sensor
one at a time. You may follow the Control Panel's
voice prompting or test the sensors in any order.
Interior sirens and speakers sound transmission beeps
as each sensoris tripped. Each beep represents one RF
pocket.
6. Count the number of transmission beeps and
refer to Table I4 for minimum requirements.
After the beeps, the Control Panel announces,
Sensor Name is activated. sensor status is XX
(XX = number of RF packets). The system Will
continue to prompt for sensors which have not
yet been tested. When all sensors have been
tested the Control Panel will announce. Sensor
terl Complete, press DONE.
7. Press DONE. The system will respond, Sensor
Text OK.
if Cancel or DONE is pressed and the Control
Panel has not heard from all sensors, the Control
Panel will respond, Sensor terr canceled orfail—
ure.
Note: Ila sensor does not meet the minimum transmission
beep requirements. refer to the it a Sensor Fails the Sensor
Test section.
Table 14 Minimum Transmission Beeps
Type of Sensor N‘JB'ZZZLO'
Wireless Intrusion Sensors W
Wireless Smoke & Heat Sensors 7—8 beeps
Wireless Environmental/Panic Buttons 7—8 beeps
Hardwtre Loops 1
Emergency Buttons‘ 7-8 beeps
* The Control Panel Emergency Button cannot be
tested.
If a Sensor Fails the Sensor Test
If sirens do not beep when a sensor is tripped, use an
[TI RF Sniffer (60-401 ) test tool to verify that the sen-
sor is transmitting. Constant beeps from the RF Sniff-
er indicate a runaway (faulty) sensor. Replace the
sensor.
If possible. locate sensors within 100 feet of the panel.
While a transmitter may have a range of 500 feet or
more out in the open. the environment at the installa-
tion site can have a signiﬁcant effect on transmitter
range. Sometimes achange in sensor location can
help overcome adverse wireless conditions.
29
To improve sensor communication, you can
' reposition the sensor
- relocate the sensor
- if necessary, replace the sensor
To reposition a sensor:
1. Rotate the sensor and test for improved sensor
communication at 90 and 180 degrees from the
original position.
If poor communication persists, relocate the sen-
sor as described as follows.
to
To relocate a sensor:
1. Test the sensor a few inches from the original
position.
2, Increase the distance from the original position
and retest until an acceptable location is found.
3. Mount the sensor in the new location,
4. If no location is acceptable, replace the sensor.
To replace a sensor:
1. Test a known good sensor at the same location.
2. If the transm n beeps remain below the mini-
mum level, avoid mounting a sensor at that loca»
tion.
3. If the replacement sensor functions, contact [Tl
for repair or replacement of the problem sensor.
Testing Phone Communication
_——_—
Perform a phone test to check the phone communica—
tion between the panel and the central station.
To perform a phone test/DL phone test:
1. Open the Control Panel cover.
2. Enter the appropriate access code.
3. Press Test twice.
4. Press DONE. The Control Panel responds with,
Phone testis on. When the phone testis com-
plete, the Control Panel will announce Phone
Test is OK.
If the panel announces Phone communicatianfailure,
proceed to the following instructions.
If the phone test fails:
1. Check that the panel is connected to the phone
jack.
30
2. Check the phone number programmed into the
paneL
Perform the phone test again.
4. If the phone test fails again, check the phone con-
nection Wiring.
3"
Testing Central Station Communica-
tion
—_—
After performing sensor and phone tests, check that
the system is reporting alarms successfully to the cen—
tral station.
To test communication with the central station:
I. Call the central station and tell the operator that
you will be testing the system,
Arm the system.
3. Test each of the wireless panic buttons and trip at
least one sensor of each type—fire, intrusion,
etcfto verify that the appropriate alarms are
working correctly.
4. When you ﬁnish testing the system, call the cen-
tral station to verify that the alarms were
received
Testing the X-10 Lamp Modules
—_
Use Table 4 to determine the full extent of module
testing to be accomplished.
To test the system controlled lamp modules:
I. Press the LIGHT button on the KeyChain
Touchpad repeatedly to turn all lights on and off.
The Control Panel responds with Light: on/oﬂ.
2. Press the Lights On button and the unit # of the
lamp module using the numeric buttons on the
Remote Handheld Touchpad to test individual
lamp modules. the Control Panel will respond
with Light: I? ordaff.
Siren and X-10 Lamp Module Func-
lions:
All Sirens will time-out in the programmed siren time-
out (I - 30 minutes). Siren priority is as follows fire,
intrusion, then emergency. If an alarm of greater pri-
ority occurs during an alarm of lower priority. the
higher priority alarm sirens scund, The X-I 0 must be
set to unit #9 to hear emergency alarm beeps. Fire
alarms will sound a temporal 3 pattern. Temproal 3 is
05 seconds on, 0.5 seconds off for 3 beeps then 1.5
seconds off.
Table 15:
Fire Intrusion Emergency
x-10 Lights Steady Hashing Steady
x, m Siren Steady Steady Alarm beeps
lnleriur & Panel Tempural 3 Sleady Fusl un/uﬂ'
Siren
Exterior Siren Temporal 3 Steady
SWIS Tempmal 3 Sleady Fasl (vii/off
31
Table 16 Troubleshooting Gulde
Problem
”1
Solution
Mm
The system says Flmctiun ltrll uvrlliublc whclt Chime
Doers is pressed.
No sensors are programmed using sensor type 10 or I3.
The system <3y< Function nol avallabh' when Chime
Special Motion is pressed.
No sensors are progrnmmerl using sensor type 25
The syslem sitys l'lmcltlm not available when LIGHTS
Time Acltvutcd is pressed
No timc activated lights have been programmed.
The system says Frurrtmn not available when LIGHTS
Sensor Activated is pressed
No sensor ‘ACIlValErJ lights have been programmed.
The system says Invalid. Sensor already programmer] as
Senior Name.
This Senmr is nlrenuy programmed. Delete sensor if not
correctly programmed,
The system Says Svnellt rime ir "0150!
Set the system time.
”ﬁll! [15 hggrgmmable by the homeowner
The Control Panel does not beep.
Program option 1 to be on.
Leirhkey does not functiun
. Latchkcy time (option 3) is not set. Set Latchkcy
limb.
- Latuhkey IS not enabled Enable Latchkey by press-
ing ARM Motion Sensors twtce.
. The plume number is ﬂat prugrammed properly
Repmgram the phone number.
Sensors
A sensor does not work
- Make sure the battery is fresh and installed cor-
recily.
- Check for interference from metal objects. Move or
rotate the scnxnr.
' anc (hr: scnsur to a new location.
Door or window 15 closed. but the Cnntml Pnnel voice
snys II is open.
- Be certain the arrow on the magnet and the guide
line on the transmitter are aligned and are within ll
4” or each other.
- The sensor may be tampered.
Mutton sensors go off continuously.
Be sure the sensor is mounted on a solid surface and the
Vtewmg field is free from sources ofchanging tempera.
ture.
Motion sensor does not respond to mulinn.
. Make sure the battery is fresh and installed cor-
rectly. Watt 2 minutes after msltllling a new battery
to test the sensor
- Adjust the sensor mounting.
- Leave the urea (or 3 minutes, then retest.
- The environment is too hot or too cold. Ouldocr
sensors will operate between 32” and IZOQF.
- Dirt or dust may be causing the problem. Wipe the
sensor with a clean, damp cloth,
x-ln Modules
All Lamp Modules or Siren not working.
- Be sure the Control Panel trunsronnerls plugged
directly into an outlet and that the outlet is not con,
trolled by at wall switch.
0 P0. hly a bad transformer.
32
Table 16 Tmubleshoollng Guide
Probiem
One Lamp Module or siren is no! wm‘king
Solution
__,
Unplug nearby equipment which may be naming
inierrerence (iighi dimmer swuches, ieIeVisioiis,
uppiinnm with older molars).
Chuck mm lh: switch on Ihc lamp or appliance is
lumed (in and remains on
Make gure [he lamp has a working bulb.
Make sure the lamp or appliance is plugged mm the:
Lamp/Appliance Module, the Module is piuggsd
iniu ihe ouilei and ihe uuilei is noi mmmllcd by a
wall SWlICh.
Make mm ihe Huuae and Unit Codes are correci.
Move ihc Module lo a different outlet lhai I5 on ihc
sum: phnse (branch) of lh: huusshold elcciiica] cii
cuii a.» ihc Comm] Panel
Time aciivawd or sensor aciivaied lighi "0! working
Make mm you have programmed [he iighr m be
aclivated by a limer Ur sensor
Make \ur€ ihc aystcm clock is sci.
Make sure these [unclions have been enabled by
prtssmg ihc LIGHTS Time Activated/Sensor Acti-
veiled on the Comm] Pancli They are enabled if [he
hum)" is in
33
Notices
Thls manual may refer lb nmducrs lllal are announced bur are nul yer ayarlable
rcc Nullea-s
nus equlpmenr has been (end and raund ruuumply wllh me llmlrs fur a class B dug
uul dents: pursuum ru purr H ul rnu FCC rules These llrnnsare rleslgnedlu praylde
reasnnable pmmcuoll agamsr narmrul lmcrfcmlwcm a resrdenual mslallauan nus
cqulpmenl aenerares, uses and ran radlare radra frequency mergy and, rlaul m-
srulleu and used rn ausurrlanre ann rue lnslruenpns may cause narmlul rmerferenee
m radru uummumcanuns ﬂawcyur mere ls nu guaranree lhal rnrerterenee wrll nur
ouuur m a pnrusular rnsrallarruu ll rlns equrpmcm docs can“: narmrul mkrkrence
m radra or lulevrsldn mepuun. wlucn czm be delennmed by lurmng me mulpmtnl
ml and lm rue userrs cncnumgzd lo rry h) euneur rne m'crfcmncc by (me ur mum el
rue lnllnwng measures
- 1mm“ a qlmhly radm 01 Inlet lsmn mmhmr aruenna ll rne rrnlunr anrennn 15
nul adenuare
. aenrlenr ar relaeare me Conlml Panel
~ Mow rne Conrrpl Fund anuy {mm rhe alleered enurpmenl
- Mme rne Canrrul Panel away fmm any w“: runs lu lhe affecled equipmem
~ (“01mm llae affeclcd caurpmem and lbe Comm! Panel re sspamle mulch. nn
drllersnl braneb clmlm
- Conwll lbe dealer ar an expenenred ramp/w reelmrulan fur Mlp
- Scml for me FCC boulder Ho» 14: Imam-um Rewlu RalanVlnrer/ereme
thlemr.a dllnble rmmrhe u s Governmenr Prlmlng umces Wasbmerpn,
n c 30402 Slack Numher 0040007002454
1'an dune anmplles wall purr ls rn llre rcc rules Operauun ls subyeq 10 rue ful—
lawrng rwp uundmans H l llus dcvlw mdy aur uause harmful lnlerferenus, and m
lhls dame rnusl aucepl any mrerlerenae reeenud, lncludmg lnlerferrnue rbal may
cause undzsm'd aneraunn
Thlscqlnpmtm mmphes Mlh para 68 ufrlre bcc rules Dn rne rcc label amaed ln
slus cquiymml l: rlle FCC Ruglslmlmn Number and ngcl Equnulanue Number
(RENJ fur llns cquipmem ll mquesred, pruynle llns rnlurmanun In your relspnnnc
mmpany
llle REN ls used lu aluulale me maxrmum number ulrleyrees yuur lelcpuune lrne
wlII suppon wull rm y seryrue ln masr arms lbs wm uh“ ueyrue RENs should
nal exczcd 5 u ( Oman yaur larul lelcpnone company «7 derernune me marrmunl
REN fur yuur rallrng area.
llyuur lelepnaae cqmpmenl causes harm lo lbs xsleplmne nelwprlr. your reluplruae
company may remporarlly drseunneer ymlr semue If passlble ynu M" be nonﬁcd
In adyanx, Whmndvrmcc nouce ls ran praunual you wlll be nunlred as snan as pus—
slble You alll aka be ndylsed dl your rlgyn ln me a fnmplnlm wun me FCL'
Yuur relrphune company may make changes m ns raulllrn-s tqmpmenl. upcrauons,
pr pruuedunes rluu cnuld aneur nae WOW npcmmm nlyuur equrpmenl You M" be
elven udwmed nunue m ardar ln manuarn ummnmplcd scr ~
ll you experlcnn‘ rumble wllh lbrs mmpmﬂ“. please cnnmcl
lnlmellye Teellnulugies, link
was Serb-rd sneer Nnrlh
Norlh lhul, m4 55m
him-177445
[or seryne and reparr mlprmarum l he lelepnane company may mk yuu m dlsccne
um llns equrpmenr from use nclwork unn| the problem hm been unarmed or unrrl
you are sure rnar rneauurnmeru rs nm mallununnalag
llnsequlpmenr may nol bcusedoll mm semczvmvidcdbylhelelzphmle company
roman. a may r...“ a asses. rs ma llmik
34
Canada Notice
We Cuudmn nepnrrrnenr olCnmmumtnnum label rdenunes penlrlea squlpmem
nus cemﬁcnuun means rlral lhr eauipmenr meets perlaln mlecmnmnmuuvns nee
wurk prureeuye. uperuuunul. unsl safely lvqulrcnwnls 7m dcpamruml dues up:
guummee llle eaulpmenl mu operate lo lne user's sallxiacmm
before msrnllrag lhls cqmpvmlm users should anxulc lhal ll ls permissible to be con-
nrr red la rue laerlules of m: kxAI leleeammunreanons campany. The cqlupmcm
mun all“) be mslﬂlled uung an uuceprable rnerllbd ulcer-neuron ln ‘nme eases. ll":
wmpnny's lasrue wlrmg assoclavzd wilh a smglalme mdivldual service may be ex'
leaded by means or a renal-red connector nsszmbly (releplume earensmn mid) Tue
eurrbrner should I»: aware rnar cnnlpllmcc wuh rhe abnve mnduimls may npr pres
year nsgmdnrrnn nl serllue in mm: suuanunn
kcpzllls Ill ccml‘lcd mulpmcm should be made by m nulhunzed Cmmlium mmme—
nanue rasrluy deslgnmed by me supplrer Any reparrs pralleranuns made by llae user
to (hls aquipmeru. ur equlpmenl ulalfurrcll'uns. may gIVI! lhu lelecummumcalluns
Lumpmly cmlsc m requesl rue llsﬂ lu drsennnm lbe equlpmenr.
lm yanrpmreeuen. make surelnar rbe elecmeal gmundumnsrlruns ulrbe palm
unllly. relepnane llncs, and rnremul nlerallrc waler prpe syrrem u presem, are ban
neeled lcgtlhtr
Caution
Do um ammpl lo mil“ conn-cllons yourseu. Com-cl |he appmpriale
almrlclan or elecrrra mspecﬂons aulhnrity.
rbe Luna Number (LN) asslgnad la eaeb lmml dsyrse denalcs rue pereenrage or
m min] lbad la be cunnrcled x0 arelepnone lupp wlllbn ls used by rue del er rn pm—
yenl nyerlnadlnp Thu lcrmrnarlan rm a loop rnay cunsrsr alany mnlhilm rm of de
mes sublecl unly la rue requuemenl lnal lhe lolnl ofllle LNs olall rbe dames dues
ran eaueed mo Lmld Number Acccplahllny Number:
”AVI e l. ‘errquerle du mmruere desCumnurnlca uru du Canada rdenune Icmmt—
ml homnlugué Cell: c‘uquene candle qu: le rnarériel esr mnfmme a eennrnes
arnmnes dc pmhxllon, d ‘txplcllalmn el de seeunle des llésczux de leleuommumua
nuns u mmlsrere n ' assure ruurelurs pus que le malerlel laneuannera a la sallsfae-
rum de l 'urrlrsnn-ur
Avam a ' rnsraller re mar el 1 ' ulr’llsaleur dalr s ‘ assure. qu' iI esr pernus A: le
mcclxdu lmx mslallanunsuel ‘enrerpnse luuals dctéléccmmunitnlinn Le mums]
ulun egulemem erre mslalle en sulyanr une mc'rmd uuueplee de raemrdemear Dans
rerlams uas. les ms inleaeurr d: l' enlsrpme ' res pour un service inuﬁvrduel a
llguc umqwt peuyenr e|r= prnlrmges an mpyen d' un drspusilifbomolbgue de mcmr—
dcmcnl lubrdnn prolunguleur relephumque lnrerne) L ’ nhmmé ne dbu pas aubller
nu 'rl esr posslbln que |.l uunlnrrrure aux commons enansées cladzssus n ' empecllv
cm pas le dégmdallun uu sewn-e daas eerluiner mlnllons Acmclkmcm. ks emer-
urlses dereleeanlmunruaunn nepermeucnl pasuuel ‘cn racamde leur mntéricl udes
lacks ll ‘ nbonné. saul dans Is; as prébis pre‘yus pas les lamfs pamculiem ue ues en,
ls-rprlses
les reparanpns de mare‘rrel homolugué umyenr err—e effelluees pus un eenue d 'e|l—
rrenen eunadlen aulprlsd designs par le faurnrsseur 14 l'llmpngne de lélécnmmuma
ealrnns peul damandsr al unlisuuur de debraueher un apparell A la sun: de
repqrmmns ou de- mudlﬁuanons ellecrue'es par I ' ullllsaleur pu a cans: dc mauyars
lunerrpnnemenr
l>uur sa prupre pruleellan. | ' unlrsaleur don s ‘ assures que mus les ms dc mlse a la
nes léléphnniqmzs nl dcs ranallsauuns
rerrs de la same rl energre eleumque, dc
a U en. meralquues at y an a. sum rauunrde's ensemble Crne weesurlun par par-
ncuuewmenr unppnnnre dans les régions mmles,
Avwrtisimem. . L ' uliliuﬂnr ne dull pas renler de false ees rummemenls Iuh
meme; doil nvmr mun-s a un seam; d ' lnspeellrm des insnallalluns fleas
iriques‘ an a elem en. selon Ie m".
Une nale =xpl|l¢alw¢ ml In: lnmce‘ dechnlgt (volrl ﬁler leuremplul,a| lnlenuun
Ms lmllsmcurs slu nralcnel lermznal. dull me inclus: dans l ‘ mfomlhlion qul nn~
Lompugm: k "1mm humak‘gué La "ale palm" elm yemgec mlnn n» mam va
vam'
'md.\ce dc charge (le amgné n chnque dispnsmf lemmml mmque pm! émer
tome wuhargt. 1c puurnrmmgc dc Ia thargﬂmnleqm pm me mwurdée n un mmuh
‘éléphomqu: was um“; par cc dxspxmul Lu lemunmson du “mm mm mu
are cunsnluée (If n ' Impnrl summc m mdmes a: Chargc a; \ 'cnscmhle as; d15~
posiufs nc damn: pm me
L ' lmlm a: chug: de m mm" m
Trademarks
m9 is a mgmcmd trademark of lnlcracuv: Tunnologm. Im sinwnm 15 n "3ch
mm of 1mm“ Trchmﬂogles. Inc X~IC9 h a regimud narkmnrk 0! x, 10
(USA). Inc
lnYEnAcnvz Tgcuuowmss.
zzss sacoun STREET NORTH
NORTH sum PAUL, MN 55109
T' s| 21777—2590
ITJZE mm
WIRELESS
Secunly
Aummatnn
Access Control
Table 17 Sensor/Device Location Planning Table Localions in order as communicated by Control Panel
when changing sensors, except the! Remote Locations are not used by the Control Panel, but only used here for
planning purposes. UPDATE WITH NEW TABLE
_ Sensor/Device Name g
2 (useTablegﬁTablea ,, 3 “5 E E E g E
'o' Indetermmessnsor & 3 5 5 o o 8 8 E no: E .. 2
g typenumbevs) tgaaegﬁ M5035?) Eg;-» M
3 Thelollowingare 23-55ng ééégﬁéseig§§é £2
examplesonlv. ziréutiémr?) SEESEBlBSmSS'SE ca
KeyChainToucl-ipnd 01 x
Door/Window 13 X
.—l.—-
-—v
_4__.__
IO l
ll
12
13 l
[4
15
16
17 J
36
Table 18 Recommended Sensor Types
UPDATE WITH NEW TABLE
. Recommended
Device
Sensor Type
KeyChain Touchpad 0| , 034 06, 07
Remote Handheld Touchpad 0]. 03, 06, 07
Indoor Motion Sensor I7 (intrusmn), 25 (chums)
Outdoor Motion Sensor
Smoke Sensor
25
—‘4
26
Extenor Door
[0
Interior Door
14
Window Sensor
13
37
Table 19 Sensor Type Characteristics UPDATE WITH NEW TABLE
'“ . . Siren T Ream [SH er Active in
2: Name/Appltcatton Delay . p
[— Type 1a] vtsory Levels
00 WCdTanlC' 21 hour audlEIe ﬁxed emergency button Intrusion I No 755 1234
01 Portable PanC' 24 hour audible portable emergency buttons Intrusion I No No 1234
02 thed Panic: 24 hour silent fixed emergency buttons Silent I No Yes 1234
03 Portable Panic“ 24 hour silent portable emergency buttons Silent I No No 1234
04 Fixed auxtltary 24 hour auxiliary sensor, such as Pendant I’anic Emergency 1 No Yes 1234
Fixed Auxiliary" 24 hour emergency button. siren shut ottconr Emergency
05 ttrms cs report [ N° YES 1234
06 Portable Auxiliary: 24 hour portable auxiliary alert button Emergency I No No 1234
Portable Auxiliary 24 hour portable auxtltary button. Stren shut Emergency
“7 orr conﬁrms cs report 1 N“ N" 1234
as Special intrusion: such as gun cabinets and wall safes. lntrttsion 1 Yes Yes 1234
09 Special lntrttston such as gun cabinets and wall sates. Intrusion 5 Yes Yes 1234
10 Entry/Bait Delay: Entry/Exit Delay that requrre a standard delay Intrusion 5 Yes Yes 24
ttme, Chime
13 instant pertmeter. Exterior doors and Windows Chime intrusion I Yes Yes 24
14 Instant Interior. interior doors Intrusion F Yes Yes 234
15 Instant Interior. Interior FIR motion sensors- Intrusion F No Yes 234
16 Instant Interior. Interior doors Intrusion F Yes Yes 34
17 Instant Interior: I’IR motion sensors' Intrusion F No Yes 34
19 pelayed Intertur’ interior doors that initiate a delay befurt: going Intrusion 5 Yes Yes 34
into alarm'
20 Delayed Interiurz'l’IR motion sensors that inttirtte a delay before Intrusion S N 0 Yes 34
gomg into alarm
21 Local Instant Interior: 24 hour local alarm zone protecting any- In mm“ I Yes Yes 1734
thmg that opens and closes. No Report
22 Local delayed tntertor: same as group 21, pips activation rnittates Intrusion 5 Yes Yes 1234
a delay before going tnto alarm. No report.
Lucdl instant Auxiliary124 hour local alarm mne protecting any- Y Y
23 thing that opens and closes 1 No report Emergenq I es es 1234
Local Instant Auxiliary: 24 hour local alarm zone protecting any- E n
24 thing that opens and closes. Sirens shut. on at resluml. No “We ‘V I Yes Yes 1234
repnn.‘
25 Local Spenal Chime. Nottfy the user when a door is ripened. TWO beeps I No YES 1234
Sounds emrt trot-n a local annunctatnrf No report
25 Fire. 24 hour fire, ralc-ufarlse heat, and smoke Sﬂn50r5§. Fire I Yes Yes 1234
27 Lamp control or other customer realm-ti No report Silent I Yes Yes 1234
23 I’IR mutton sensor, sound sensor, or pressure mat t Nu report Silent I No Yes 1234
29 Auxlltary: freeze sensor Emergency l Yes Yes 1234
32 PIR motion sensor or sound sensor: Nu report Silent I No No 1234
‘Thls typo ts not Ccniﬁed as a primary protection Clrcull for UL— Delays-
tisted systems and is for supplementary use only. I : hm,“ Delay (no delay, immediate alarm)
§Thls type is requtrcd tor UL-llsled residential ﬁre alarm appltca- s = Standard Delay (alarm sounds after programmed entry delay
time)
F : Follower Delay (alarm sounds immediately irentry/extt delay
is not active, otherwise alarm sounds after programmed entry de-
The arming levels are: lay time)
tit-ins.
iThis type has not been Investigated by UL
I = Dlsarm
2 : Arm Doors & WIIIdUWS
3 : Arm Motion Sensors
4 = Arm Doors/Windows & Motion Sensors
38
Table 20 Home Control Planning Table UPDATE WITH NEW TABLE
Module Activated by Tlme Adlvated
Unlt # Type Location Sensar Entry/Exit start Time Slop Time
r-
Examplc Lamp Hall lamp Motion Yes 8 pm 10:30 pm.
_——T
6 1——
Table 21 Programmable Options UPDATE WITH NEW TABLE
"1—
wnn c." Chlnge:
“we, U1 - Ulilily
Access Code 1,
°"' 5mm" Funcﬂon Dora-m Ran - ' '""’“”
mm » Fsamre 5' ”2 unmy Mlngl
Access cm 2: M
Human - Math”
Access Code.
4—-
01 Panel Beeps On On/Off U1 U2 M A
02 Panel Voicc On Dn/Off U1 U2 M A
03 Reparls as Lalchkey Option Off 12:(X) am. U1 U2 M A
99 - 11:59
pm.
04 Primary Phone Nnmhcr None 22 digits u
05 Secondary Phone Number None 22 digxls Ul
06 Downloader Phone Number None 22 digits U1
07 Accounl Number (10000 00000- U1 U2
99999
08 Phone Lock 011 Orr/Off U1
09 Dcwnloader Code 12345 00000 U1
99999
10 Entry Delay 30 sex: 0057120 U1 U2
sec
11 Exit Delay 30 Sec 0057120 U1 U2
sec
L.
I2 Phone Mod 1 0 03 U1
39
Table 21 Programmable Options UPDATE WITH NEW TABLE
wnzjeanuﬁRr-gn:
u r
“3:3“, $551 Function Del-lull Huge m ‘ C“. M $1.12;
Number
Aeeul Codie
13 L Phone Mod 2 0 0-9 U1
Id DTMF On Oil/Off U1 U2
15 79 N0 Acuvlly Off 02—24 hr: U1 U2
16 93 Aulo Phone Test Option (Must be enabled for Off 0017254 U1 U2
UL Listed >y
Source Exif Data:
File Type : PDF
File Type Extension : pdf
MIME Type : application/pdf
PDF Version : 1.2
Linearized : Yes
Create Date : 2001:05:30 09:38:52
Producer : Acrobat Distiller 4.0 for Windows
Modify Date : 2001:05:30 09:38:53-04:00
Page Count : 43

EXIF Metadata provided by EXIF.tools

UTC Fire and Security Americas 735-XMTR User Manual 8

UTC Fire & Security Americas Corporation, Inc. 8

Contents

8

FCC ID Filing: B4Z-735-XMTR

Navigation menu

Namespaces

Views

Navigation