Ubiquiti ISM5 IsoStation M5 User Manual airOS v5 6 User Guide

Ubiquiti Networks, Inc. IsoStation M5 airOS v5 6 User Guide

OSG

Download:
Mirror Download [FCC.gov]
Document ID	3286223
Application ID	qTjDo71hm588vrRXP7RVzw==
Document Description	OSG
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	182.42kB (2280206 bits)
Date Submitted	2017-02-16 00:00:00
Date Available	2017-08-16 00:00:00
Creation Date	2017-02-13 17:52:56
Producing Software	Acrobat Distiller 15.0 (Windows)
Document Lastmod	2017-02-13 17:52:56
Document Title	airOS v5.6 User Guide
Document Creator	Adobe InDesign CC 2015 (Macintosh)
Document Author:	J Lee

Operating System for UbiquitiÂŽ M Series Products
Release Version: 5.6
airOSÂŽ v5.6 User Guide
Table of Contents
Table of Contents
Chapter 1: Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Supported Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
airOS v5.6 Network Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
airOS v5.6 Wireless Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
M Series Product Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Chapter 2: Main . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Chapter 3: Ubiquiti Logo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
airMAX Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
airSelect. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
airView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
airSync (GPS Series Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Chapter 4: Wireless . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Basic Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Wireless Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Chapter 5: Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Network Role . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Configuration Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Management Network Settings â Bridge Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Management Network Settings â Router or SOHO Mode . . . . . . . . . . . . . . . . . . . . . . . . .34
WAN Network Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
LAN Network Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
DHCP Address Reservation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Port Forwarding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Multicast Routing Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
IP Aliases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
VLAN Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Bridge Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
IPv6 Firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Static Routes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
IPv6 Static Routes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Traffic Shaping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Ubiquiti Networks, Inc.
Table of Contents
airOSÂŽ v5.6 User Guide
Chapter 6: Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Advanced Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Advanced Ethernet Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Signal LED Thresholds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Chapter 7: Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Ping Watchdog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
SNMP Agent. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Telnet Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
NTP Client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Dynamic DNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
System Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Device Discovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Chapter 8: System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Firmware Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Date Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
System Accounts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Miscellaneous . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Device Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Configuration Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Chapter 9: Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Align Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Site Survey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Discovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Ping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Traceroute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Speed Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
airView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Appendix A: Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Ubiquiti Networks Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
ii
Ubiquiti Networks, Inc.
airOSÂŽ v5.6 User Guide
Chapter 1: Overview
Introduction
Chapter 1: Overview
Supported Products
airOS v5.6 supports the M Series product versions,
including the following:
â˘ airRouterâ˘
Welcome to airOSÂŽ v5.6 â the latest evolution of the airOS
&RQILJXUDWLRQÂŠ,QWHUIDFHÂŠE\ÂŠ8ELTXLWLÂŠ1HWZRUNVÂŠDLU26YÂŠ
provides numerous updates, including:
â˘ Rocketâ˘M GPS
â˘ Private SNMP MIB
â˘ Rocketâ˘M Titanium
â˘ IPv6 Support
â˘ NanoBeamÂŽM
â˘ QoS for VLANs
â˘ NanoBridgeÂŽM
â˘ Password Length increased to More than 8 Symbols
â˘ NanoStationÂŽlocoM/NanoStationM
â˘ TCP Support for Remote System Logging
â˘ Bulletâ˘M
â˘ WPA-AES/WPA2-AES Security Only (WEP optional for
AP-Repeater mode)
â˘ Bulletâ˘M Titanium
â˘ 5 MHz Increments Available for Frequency Selection
When 5 GHz Devices Operate in airMAXÂŽ Mode (instead
of channel shifting)
â˘ PowerBeamâ˘M
airOS is an advanced operating system capable of
powerful wireless and routing features, built upon a
simple and intuitive user interface foundation.
This User Guide describes the airOS operating system
version 5.6, which is integrated into all M Series products
provided by Ubiquiti Networks.
Note: For compatibility, legacy or 802.11 a/b/g
devices should use legacy firmware with airMAX
support (such as airOS firmware v4.0). Legacy
clients can only work as airMAX clients with the M
Series device acting as an airMAX AP.
Ubiquiti Networks, Inc.
â˘ Rocketâ˘M
â˘ PicoStationÂŽM
â˘ PowerBridgeÂŽM
â˘ airGridÂŽM
â˘ WispStationâ˘M
â˘ airGatewayâ˘
For more information, visit: www.ubnt.com
airOS v5.6 Network Modes
airOS supports the following network modes:
â˘ Transparent Layer 2 Bridge
â˘ Router
â˘ SOHO Router
Chapter 1: Overview
airOS v5.6 Wireless Modes
airOS supports the following wireless modes:
â˘ Access Point
airOSÂŽ v5.6 User Guide
4. Upon subsequent login, the standard login screen
appears. Enter ubnt in the Username and Password
fields, and click Login.
â˘ Station / Client
â˘ AP-Repeater
System Requirements
â˘ Microsoft Windows 7/8, Linux, or Mac OS X
â˘ Java Runtime Environment 1.6 (or above)
â˘ Web Browser: Mozilla Firefox, Apple Safari, Google
Chrome, or Microsoft Internet Explorer 8 (or above)
Getting Started
To access the airOS Configuration Interface, perform the
following steps:
1. Configure the Ethernet adapter on your computer
with a static IP address on the 192.168.1.x subnet (for
example, IP address: 192.168.1.100 and subnet mask:
255.255.255.0).
2. Launch your web browser. Enter https:// and the
default IP address of your device in the address field.
Press Enter (PC) or Return (Mac).
Device
Default IP Address
airRouter
192.168.1.1
Other Devices
192.168.1.20
Note: HTTPS is the default protocol starting with
airOS v5.5.4.
For example, enter 192.168.1.20 to access the Rocket.
3. Upon initial login, the Terms of Use appear on the login
screen. Enter ubnt in the Username and Password fields,
and select the appropriate choices from the Country
and Language drop-down lists. Check the box next to
agree to t ese terms of use, and click Login.
Note: To enhance security, we recommend that
you change the default login in System > System
Accounts. For details, go to âSystem Accountsâ on
page 54.
M Series Product Verification
Starting with M series product models manufactured in
2012, the airOS Configuration Interface (v5.5.2 or later) will
verify whether a product is genuine or counterfeit.
Prior to 2012
For M series product models manufactured prior to 2012,
airOS will NOT display any logo in the lower left corner of
the screen.
Starting in 2012
For new M series product models introduced in 2012 or
later, airOS will display a Genuine Product logo in the
lower left corner of the screen.
New production versions of existing M series product
models began using the Genuine Product logo in 2012.
1RWDOOÂŠ0VHULHVÂŠSURGXFWÂŠPRGHOVÂŠPDQXIDFWXUHGÂŠLQÂŠÂŠ
will display a Genuine Product logo.)
For any M series product that is not an official Ubiquiti
product, airOS will display a counterfeit warning. Please
contact Ubiquiti at support@ubnt.com regarding
WKLVSURGXFW
Note: If neither the Genuine Product logo nor
counterfeit warning appears, the device was
manufactured prior to the genuine product
verification process and is probably genuine.
If you have any questions, please email
support@ubnt.com.
Ubiquiti Networks, Inc.
airOSÂŽ v5.6 User Guide
Chapter 1: Overview
Navigation
The airOS Configuration Interface contains seven main
pages, each of which provides a web-based management
page to configure a specific aspect of the Ubiquiti device:
â˘ Ubiquiti Logo The âUbiquiti Logoâ on page 15
controls Ubiquitiâs proprietary technologies, such as
airMAX, airView, airSelect, and airSync (GPS Series
devices only).
Note: By default, indoor products, such as the
airRouter, do not display the Ubiquiti logo page.
However, you can enable the Ubiquiti logo
page through System > Miscellaneous > airMAX
Tec nology eatures. For more information, see
âMiscellaneousâ on page 55.
â˘ Main The âMainâ on page 5 displays device status,
statistics, and network monitoring links.
â˘ Wireless The âWirelessâ on page 23 configures
basic wireless settings, including the wireless mode,
Service Set Identifier (SSID), 802.11 mode, channel and
frequency, output power, data rate module, and wireless
security.
â˘ Network The âNetworkâ on page 31 configures the
network operating mode; Internet Protocol (IP) settings;
IP aliases; VLANs; packet filtering, bridging, and routing
routines; and traffic shaping.
â˘ Advanced The âAdvancedâ on page 45 provides
more precise wireless interface controls, including
advanced wireless settings, advanced Ethernet settings,
and signal LED thresholds.
â˘ Services The âServicesâ on page 49 configures
system management services: Ping Watchdog, Simple
Network Management Protocol (SNMP), servers (web,
SSH, Telnet), Network Time Protocol (NTP) client,
Dynamic Domain Name System (DDNS) client, system
log, and device discovery.
â˘ System The âSystemâ on page 53 controls
system maintenance routines, administrator account
management, location management, device
customization, firmware update, and configuration
backup. You can also change the language of the web
management interface.
Each page also contains network administration and
monitoring tools:
â˘ âAlign Antennaâ on page 57
â˘ âSite Surveyâ on page 57
â˘ âDiscoveryâ on page 58
â˘ âPingâ on page 58
â˘ âTracerouteâ on page 59
â˘ âSpeed Testâ on page 59
â˘ âairViewâ on page 60
Ubiquiti Networks, Inc.
Chapter 1: Overview
airOSÂŽ v5.6 User Guide
Ubiquiti Networks, Inc.
airOSÂŽ v5.6 User Guide
Chapter 2: Main
The Main page displays a summary of the link status
information, current values of the basic configuration
settings (depending on the operating mode), network
settings and information, and traffic statistics.
Status
Ubiquiti Networks, Inc.
Chapter 2: Main
Device Name Displays the customizable name or
identifier of the device. The Device Name (also known
as host name) is displayed in registration screens and
discovery tools.
Network Mode Displays the network operating mode.
airOS supports three modes: Bridge, Router, and SOHO
Router. The default setting is device-specific. Configure the
Network Mode on the Network page (for details, refer to
âNetwork Roleâ on page 31).
Chapter 2: Main
Wireless Mode Displays the operating mode of the
radio interface. airOS supports three operating modes:
Station, Access Point, and AP-Repeater. The default setting
is device-specific. Configure the Wireless Mode on the
Wireless page. If Station or Access Point mode is enabled,
then you can also select WDS (Wireless Distribution
System) as needed.
airOS also supports airView (spectrum analyzer) mode, a
temporary mode that terminates all wireless connections.
To select airView mode, click Tools > airView or click
Launch airView on the Ubiquiti Logo page. When the
device is running in airView mode, all wireless connections
will be terminated during the airView session. Close the
airView window to return to the previous wireless mode.
Any M Series device may operate in only one of these
modes at a time. For example, if the device is running
in Access Point mode, it cannot simultaneously run in
StationPRGH
SSID Displays the wireless network name (SSID). The
wireless network name depends upon the wireless mode
selected:
â˘ In Station mode, this displays the SSID of the AP the
device is associated with.
â˘ In Access Point mode, this displays the SSID configured
on the device using the Wireless page.
Security Displays the wireless security method being
used on the device. If None is displayed, then wireless
security has been disabled, although you can still use
RADIUS MAC authentication.
Version Displays the airOS software version.
Uptime This is the total time the device has been running
since the latest reboot (when the device was powered up)
or software upgrade. The time is displayed in days, hours,
minutes, and seconds.
Date Displays the current system date and time, which
is retrieved from the Internet using NTP (Network Time
Protocol). The NTP Client is disabled by default on the
Services page. The device doesnât have an internal clock,
and the date and time may be inaccurate if the NTP Client
is disabled or the device isnât connected to the Internet.
airOSÂŽ v5.6 User Guide
Channel/Frequency Displays the channel number and
corresponding operating frequency. The device uses
the channel and radio frequency specified to transmit
and receive data. Valid channel and frequency ranges
will vary depending on local country regulations. If the
Channel/Frequency is labeled as âDFSâ, then the device is
using a DFS (Dynamic Frequency Selection) channel. (DFS
channels/frequencies are not available on all devices.)
Channel Width This is the spectral width of the radio
channel used by the device. airOS v5.6 supports 3, 5, 7,
8, 10, 14, 20, 25, 28, 30, and 40 MHz; however, available
channel widths are device-specific. In Station mode, Auto
20/40 MHz is the value by default.
Frequency Band Displays the actual operating frequency
range of the device. This is based on the selected
frequency, channel width, and extension channel on the
Wireless page.
Distance Displays the current distance between devices
in kilometers and miles for Acknowledgement (ACK)
frames. Changing the distance value will change the
ACK (Acknowledgement) timeout accordingly. The ACK
timeout specifies how long the device should wait for
an acknowledgement from a partner device confirming
frame reception before it concludes that there has been
an error and resends the frame. You can adjust the
Distance value; for more information, see âDistanceâ on
page 46).
TX/RX Chains Displays the number of independent
spatial data streams the device is transmitting (TX)
and receiving (RX) simultaneously within one spectral
channel of bandwidth. This ability is specific to 802.11n
devices that rely on Multiple-Input Multiple-Output
(MIMO) technology. Multiple chains increase data transfer
performance significantly. The number of chains Ubiquiti
devices use is hardware-specific because every TX/RX
chain requires a separate antenna.
Antenna (Only applicable to devices with antenna
options.) The antenna type (Internal, External, or External +
Internal) is displayed. For more information, see âAntennaâ
on page 26.
WLAN0 MAC Displays the MAC address of the device as
seen on the wireless network.
LAN0 MAC Displays the MAC address of the device as
seen on the LAN.
LAN1 MAC Displays the MAC address of the device
as seen on the WAN interface. This is the deviceâs MAC
address as seen over the Internet.
LAN0/LAN1 Displays the Ethernet port speed and duplex
mode, such as 1000Mbps-Full or 100Mbps-Full. This can
indicate that a cable is not plugged into a device or there
is no active Ethernet connection.
AP MAC In Access Point or AP-Repeater mode, this
displays the MAC address of the device. In Station mode,
this displays the MAC address of the AP the device is
associated with.
Ubiquiti Networks, Inc.
airOSÂŽ v5.6 User Guide
Signal Strength (Available in Station mode only.)
Displays the received wireless signal level (client-side).
The represented value coincides with the graphical bar.
Use the antenna alignment tool to adjust the device
antenna to get a better link with the wireless device. The
antenna of the wireless client has to be adjusted to get
the maximum signal strength. Signal Strength is measured
in dBm (the decibels referenced to 1 milliwatt). The
FRQYHUVLRQÂŠLVÂŠGHILQHGÂŠDVÂŠG%P ORJ 3P: ÂŠ6RÂŠG%PÂŠ
would be 1 mW and -72 dBm would be 0.0000006 mW.
A signal strength of -80 dBm or better (-50 to -70 dBm) is
recommended for stable links.
Chain or Horizontal/Vertical or External/Internal
(Vertical) (Available in Station mode only.) Displays
the wireless signal level (in dBm) of each signal. Devices
with fixed antennas display Horizontal/Vertical instead of
Chain. When chains are displayed, the number of chains is
device-specific.
The NanoStationM900 loco displays External/Internal
(Vertical) if the Antenna option on the Wireless page is
set to External + Internal (2x2). For more information, see
âAntennaâ on page 26.
Connections (Available in Access Point or AP-Repeater
mode only.) Displays the number of wireless devices
connected to the device.
Noise Floor Displays the current value (in dBm) of the
environmental noise (from interference) the receiver hears
on the operating frequency. airOS considers the Noise
Floor while evaluating the signal quality (Signal-to-Noise
Ratio SNR, RSSI). The value mean depends on the signal
strength above the Noise Floor.
Transmit CCQ This index evaluates the wireless Client
Connection Quality (CCQ). The level is based on a
percentage value for which 100% corresponds to a perfect
link state.
TX Rate/RX Rate (Available in Station mode only.)
Displays the current 802.11 data transmission (TX) and
data reception (RX) rates.
airMAX Indicates the airMAX status. If airMAX is enabled,
the device will only accept airMAX clients. airMAX also
features advanced QoS autodetection settings. For more
information, refer to âairMAX Settingsâ on page 15.
Ubiquiti Networks, Inc.
Chapter 2: Main
Note: For compatibility, legacy or 802.11 a/b/g
devices should use legacy firmware with airMAX
support (such as airOS firmware v4.0). Legacy
clients can only work as airMAX clients with the M
Series device acting as an airMAX AP.
airMAX Priority Available if airMAX is enabled in Station
mode only. Indicates the airMAX Priority set on the Ubiquiti
logo page. By default the AP gives all active clients
the same amount of time. However, if the clients are
configured with different priorities, the AP will give clients
more or less time, depending on the priority.
airMAX Quality Available if airMAX is enabled. airMAX
Quality (AMQ) is based on the number of retries and the
quality of the physical link. If this value is low, you may
have interference and need to change frequencies. If AMQ
is above 80% and you do not notice any other issues, then
you do not need to make any changes.
airMAX Capacity Available if airMAX is enabled. airMAX
Capacity (AMC) is based on airtime efficiency. For example,
if you have one client with a low data rate or you are using
a 1x1 device (such as Bullet or airGrid) alongside other
clients that are 2x2, then it will use up more airtime (slots)
for the same amount of data, reducing time (or capacity)
for other clients. The lower the AMC, the less efficient the
AP is. If you only have one client, this may not matter, but
when you have many clients (for example, more than 30),
then AMC becomes very important, and you want it to be
as high as possible.
If you are looking at the client, AMC shows the theoretical
capacity of that client, based on current TX/RX rates and
quality. AMC is a percentage based on what the maximum
performance would be if the link were perfect. Clients
with poor airtime efficiency can negatively affect other
clients by taking up more airtime while transmitting at
ORZHUÂŠVSHHGVÂŠ)RUÂŠH[DPSOHÂŠFOLHQWÂŠ$ÂŠLVÂŠDWÂŠ0&6ÂŠÂŠ 0ESV ÂŠ
because of low signal. The client could theoretically
do MCS 15 (130 Mbps), so AMC is based on the ratio
of current rate/maximum rate (78 Mbps divided by
0ESV ÂŠZKLFKÂŠLVÂŠÂŠ,QÂŠDÂŠVLPLODUÂŠIDVKLRQÂŠDÂŠ[ÂŠGHYLFHÂŠ
will always have a maximum AMC of 50%, because it
provides half the performance of a 2x2 device.
If you are looking at the AP, then AMQ and AMC are
averages of all clientsâ values. If you want to discover
what is lowering your values on heavily populated APs,
single out the weak clients. You can either use airControlâ˘
(recommended), or you can go to each client individually.
Try to upgrade to a higher-gain antenna (to allow a better
data rate), or upgrade to a 2x2 device if you are using a
1x1 device.
airSelect (Available in Access Point or AP-Repeater mode
only.) Indicates the airSelect status. If airSelect is enabled,
airSync is not available. Access airSelect setup through
Ubiquiti Logo > airSelect.
Hop Interval Available if airSelect is enabled. The duration
(in milliseconds) that the AP will stay on one frequency
before moving to the next.
Chapter 2: Main
airOSÂŽ v5.6 User Guide
airSync (GPS Series Only) Indicates the airSync status. If
airSync is enabled, airSelect is not available, and the device
in Master mode reports the number of airSync-enabled
devices in Slave mode. Access airSync setup through
Ubiquiti Logo > airSync.
GPS Signal Quality (GPS Series Only) Displays GPS
signal quality as a percentage value on a scale of 0-100%.
Latitude/Longitude (GPS Series Only) Based on
GPS tracking, reports the deviceâs current latitude and
longitude. Clicking the link opens the reported latitude
and longitude in a browser using Google Mapsâ˘
(http://maps.google.com).
Altitude (GPS Series Only) Based on GPS tracking,
reports the deviceâs current altitude above sea level.
Custom Scripts Displayed if custom scripts are present
on the device. If custom scripts are running, then the Main
page displays the status of this option as âDetectedâ and
the Manage button. Click Manage and the Custom Scripts
Management screen appears:
airMAX Gateway Displayed if your airMAX device is a CPE
connected to an airMAX Gateway. You can click Connected
(Click to manage) to remotely provision the airGateway.
The CPE must be running airOS v5.5.8 or higher to be
compatible for pairing. Follow these instructions on
WKH&3(
1. On the Wireless page, configure Wireless Mode: Station.
2. On the Network page, configure Network Mode: Router.
3. For the Configuration Mode, select Advanced.
4. View the Bridge Network section. Remove all ports and
then remove the Bridge. (Refer to âWAN Network
Settingsâ on page 34 for more information.)
â˘ Enabled Select to run the custom script.
5. In the LAN Network Settings section, add LAN0 and
configure the rest of the settings. (Do not use the
192.168.1.x subnet on the CPEâs LAN0 setup.)
â˘ Script Name Displays a descriptive name.
6. Click Change.
â˘ Download Script Click to download the custom script.
To pair the airGateway, follow these instructions:
â˘ Remove Script Click to delete the custom script.
1. Reset the airGateway to its factory defaults. (If the
devices are already connected, then reboot both
devices.)
â˘ Save To save changes, click Save.
Note: The device will be automatically restarted
when changes are saved.
â˘ Close To close this screen, click Close.
2. Follow the instructions in the airGateway Quick Start
Guide (available at downloads.ubnt.com) to connect
the airGateway to the CPE.
3. Access the Configuration Interface of the CPE.
4. On the Main page, click Connected (Click to manage)
to remotely access the airGateway.
Ubiquiti Networks, Inc.
airOSÂŽ v5.6 User Guide
Monitor
There are various monitoring tools accessible via the links
on the Main page. The default is Throughput, which is
displayed when you first open the Main page.
Throughput
Chapter 2: Main
Latency (Available if the Auto Adjust setting is enabled
through Advanced Wireless > Advanced Wireless Settings.)
Displays the latency value, in milliseconds, for wireless
frames.
Distance (Available if the Auto Adjust setting is enabled
through Advanced Wireless > Advanced Wireless Settings.)
Displays the current distance between devices in miles for
Acknowledgement (ACK) frames. Click miles to display
the distance in km. Then you can click km to display the
distance in miles.
With Auto Adjust enabled, the auto-acknowledgement
timeout algorithm of the device dynamically optimizes
the frame acknowledgement timeout value without user
intervention.
Throughput displays the current data traffic on the LAN
and WLAN in both graphical and numerical form. The
chart scale and throughput dimension (Bps, Kbps, Mbps)
change dynamically depending on the mean throughput
value. The statistics are updated automatically.
Refresh If there is a delay in the automatic update, click
Refresh to manually update the statistics.
Stations
(Available in Access Point or AP-Repeater mode only.)
This selection lists the stations that are connected to the
device.
TX/RX, Mbps The TX value represents the data rates, in
Mbps, of the last transmitted packets, and the RX value
represents the data rates, in Mbps, of the last received
packets.
CCQ, % This index evaluates the wireless Client
Connection Quality (CCQ). The level is a percentage value
for which 100% corresponds to a perfect link state.
Connection Time Displays the stationâs association time
to the AP. The time is expressed in days, hours, minutes,
and seconds.
Last IP Displays the stationâs last IP address. Click the IP
address to access the device.
Action Displays available options for this station. For
example, click kick to drop the connection to this station.
Refresh To update the information, click Refresh.
The following statistics for each station are displayed in
the station statistics window:
Station MAC Displays the MAC address of the station.
This is a clickable link that will display additional station
information.
Station Information
Detailed information is displayed when you click a specific
MAC address:
Device Name Displays the stationâs host name. The
device name can be changed on the System page.
TX Signal, dBm The TX Signal, dBm Combined value
represents the last transmitted wireless signal level. Click
Combined to display the separate Chain 0 and Chain 1
signal values. Then you can click Chain0/Chain1 to display
the combined signal value. (Devices with fixed antennas
display Horizontal/Vertical instead of Chain. When chains
are displayed, the number of chains is device-specific.)
RX Signal, dBm The RX Signal, dBm Combined value
represents the last received wireless signal level. Click
Combined to display the separate Chain 0 and Chain 1
signal values. Then you can click Chain0/Chain1 to display
the combined signal value. (Devices with fixed antennas
display Horizontal/Vertical instead of Chain. When chains
are displayed, the number of chains is device-specific.)
Noise, dBm The Noise value represents the noise level.
â˘ Station Displays the MAC address of the station.
â˘ Device Name Displays the host name of the station.
â˘ Product Displays the product name of the device.
â˘ Firmware Displays the firmware version of airOS.
â˘ Connection Time Displays the amount of time the
station has been connected to the device. The time is
expressed in days, hours, minutes, and seconds.
Ubiquiti Networks, Inc.
Chapter 2: Main
â˘ RX Signal The value represents, in dBm, the last
received wireless signal level.
â˘ TX Signal The value represents, in dBm, the last
transmitted wireless signal level.
â˘ Noise Floor Displays the current value (in dBm) of the
environmental noise (from interference) the receiver
hears on the operating frequency. airOS considers
the Noise Floor while evaluating the signal quality
(Signal-to-Noise Ratio SNR, RSSI). The value mean
depends on the signal strength above the Noise Floor.
â˘ Distance (Available if the Auto Adjust setting is
enabled through Advanced Wireless > Advanced Wireless
Settings.) Displays the current distance between
devices in kilometers and miles for Acknowledgement
(ACK) frames. With Auto Adjust enabled, the deviceâs
auto-acknowledgement timeout algorithm dynamically
optimizes the frame acknowledgement timeout value
without user intervention.
airOSÂŽ v5.6 User Guide
â˘ Negotiated Rate/Last Signal, dBm Values represent
the received wireless signal level along with the data
rates of recently received packets. N/A is displayed as the
Last Signal if no packets were received on that specific
data rate.
â˘ Kick To drop the connection to the station, click Kick.
â˘ Refresh To update the information, click Refresh.
â˘ Close To close the Station Info window, click Close.
AP Information
(Available in Station mode only.) This selection lists the
connection statistics of the AP associated with the device.
â˘ CCQ The value represents the quality of the connection
to the AP. This index evaluates the wireless Client
Connection Quality (CCQ). The level is a percentage
value for which 100% corresponds to a perfect link state.
â˘ TX Power Displays the transmit power (in dBm) of the
station.
â˘ airMAX Priority The airMAX Priority of this stationâs
traffic in comparison to the other stations.
â˘ airMAX Quality The airMAX Quality level is based on
a percentage value for which 100% corresponds to a
perfect link state.
â˘ airMAX Capacity This is an index of the maximum data
rate the link is operating at. A lower capacity number
indicates a unit that is slowing down the system.
Access Point Displays the MAC address of the AP.
Device Name Displays the host name of the AP.
â˘ Last IP Displays the stationâs last IP address. Click the IP
address to access the device.
Product Displays the product name of the device.
â˘ TX/RX Rate Displays the actual 802.11n data rate,
which is restricted by the wireless link modulation/
mode/protocol used, in Mbps, of the last transmitted
and received packets.
Connection Time Displays the amount of time the device
has been connected to the AP. The time is expressed in
days, hours, minutes, and seconds.
â˘ TX/RX Bit Rate Displays the actual bit rate, in bps,
of the user data/traffic load/data stream/throughput
(the number of bits transmitted and received from the
station during the last second).
â˘ TX/RX Packets Displays the total number of packets
transmitted and received from the station during the
connection uptime.
â˘ TX/RX Packet Rate, pps Displays the mean value of the
transmitted and received packet rates.
â˘ Bytes Transmitted Displays the total amount of data
(in bytes) transmitted during the connection and a userfriendly equivalent in parentheses. Example:
Bytes Transmitted: 6329846 (6.33 MBytes)
â˘ Bytes Received Displays the total amount of data
(in bytes) received during the connection and a userfriendly equivalent in parentheses.
10
Firmware Displays the firmware version of airOS.
RX Signal The value represents, in dBm, the last received
wireless signal level.
TX Signal The value represents, in dBm, the last
transmitted wireless signal level.
Noise Floor Displays the current value (in dBm) of the
environmental noise (from interference) the receiver hears
on the operating frequency. airOS considers the Noise
Floor while evaluating the signal quality (Signal-to-Noise
Ratio SNR, RSSI). The value mean depends on the signal
strength above the Noise Floor.
Distance (Available if the Auto Adjust setting is enabled
through Advanced Wireless > Advanced Wireless Settings.)
Displays the current distance between devices in miles for
Acknowledgement (ACK) frames. Click miles to display
the distance in km. Then you can click km to display the
distance in miles.
Ubiquiti Networks, Inc.
airOSÂŽ v5.6 User Guide
CCQ The value represents the quality of the connection to
the AP. This index evaluates the wireless Client Connection
Quality (CCQ). The level is a percentage value for which
100% corresponds to a perfect link state.
Last IP Displays the deviceâs last IP address. Click the IP
address to access the device.
TX/RX Rate Displays the actual 802.11n data rate, which
is restricted by the wireless link modulation/mode/
protocol used, in Mbps, of the last transmitted and
received packets.
TX/RX Bit Rate Displays the actual bit rate, in bps, of
the user data/traffic load/data stream/throughput (the
number of bits transmitted and received from the station
during the last second).
TX/RX Packets Displays the total number of packets
transmitted and received from the station during the
connection uptime.
TX/RX Packet Rate, pps Displays the mean value of the
transmitted and received packet rates.
Chapter 2: Main
IP Address Displays the IP addresses of the interface.
Note: There are typically two addresses per
management interface in case IPv6 is enabled.
Example:
192.168.1.20 FE80::227:22FF:FEEC:E770/64
RX Bytes Displays the total amount of data (in bytes)
received by the interface.
RX Errors Displays the number of receive errors.
TX Bytes Displays the total amount of data (in bytes)
transmitted by the interface.
TX Errors Displays the number of transmit errors.
Refresh To update the information, click Refresh.
DHCP Client
(Available in Router or SOHO Router mode only.) Displays
the deviceâs WAN IP address, netmask, DNS servers, and
gateway while the device is operating as a DHCP client of
an external DHCP server.
Bytes Transmitted Displays the total amount of data (in
bytes) transmitted during the connection and a userfriendly equivalent in parentheses. Example:
Bytes Transmitted: 6329846 (6.33 MBytes)
Bytes Received Displays the total amount of data (in
bytes) received during the connection and a user-friendly
equivalent in parentheses.
Negotiated Rate/Last Signal, dBm Values represent the
received wireless signal level along with the data rates
of recently received packets. N/A is displayed as the Last
Signal if no packets were received on that specific data
rate.
Reconnect To establish the wireless link to the AP again,
click Reconnect.
Refresh To update the information, click Refresh.
Interfaces
Displays the name, MAC address, MTU, IP address, and
traffic information for the deviceâs interfaces.
Interface Displays the interface that connects to the
WAN.
IP Address Displays the IP address assigned by an
external DHCP server connected to the WAN interface.
If an external DHCP server is not found, the IP address
will use the DHCP Fallback IP defined in the WAN Network
Settings. See âWAN Network Settingsâ on page 34 for
additional details.
Netmask Displays the Netmask assigned by an external
DHCP server connected to the WAN interface. If an
external DHCP server is not found, the IP address will use
the DHCP Fallback Netmask defined in the WAN Network
Settings. See âWAN Network Settingsâ on page 34 for
additional details.
Gateway Displays the gateway address assigned by an
external DHCP server connected to the WAN interface.
Interface Displays the name of the interface.
MAC Address Displays the MAC address of the interface.
MTU Displays the Maximum Transmission Unit (MTU),
which is the maximum frame size (in bytes) that a network
interface can transmit or receive. The default is 1500.
Primary/Secondary DNS IP Displays the DNS IP
address(es) assigned by an external DHCP server. The
Domain Name System (DNS) is an Internet âphone bookâ
that translates domain names to IP addresses. These fields
identify the server IP addresses that the device uses for
translation.
DHCP Server Displays the IP address of the external
DHCP server that assigns the WAN IP address to the
device.
Domain Displays the domain name.
Ubiquiti Networks, Inc.
11
Chapter 2: Main
Total Lease Time Shows the total time (validity) of the
leased IP address assigned by the external DHCP server.
Remaining Lease Time Displays the remaining time
of the leased IP address assigned by the external DHCP
server.
Renew To request new IP settings from the external
DHCP server, click Renew.
Release To release the current IP settings, click Release.
Note: Releasing the DHCP clientâs IP settings may
terminate the management connection to the
device.
Refresh To update the information, click Refresh.
airOSÂŽ v5.6 User Guide
Interface The Bridge Table shows which bridge port
or interface, LAN (Ethernet) or WLAN (Wireless), the
specific network device is associated with. airOS can
forward packets only to the specified port of the device,
eliminating redundant copies and transmits.
Aging Timer Displays aging time for each address entry
(in seconds). After a specific timeout, if the device has not
seen a packet coming from a listed address, it will delete
that address from the Bridge Table.
Refresh To update the information, click Refresh.
Routes
Lists all the entries in the system routing table.
ARP Table
Lists all the entries of the Address Resolution Protocol
(ARP) table currently recorded on the device.
ARP is used to associate each IP address to the unique
hardware MAC address of each device on the network. It
is important to have unique IP addresses for each MAC
address or else there will be ambiguous routes on the
network.
IP Address Displays the IP address assigned to a network
device.
MAC Address Displays the MAC address of the device.
Interface Displays the interface that connects to the
device.
airOS examines the destination IP address of each data
packet traveling through the system and chooses the
appropriate interface to forward the packet to. The system
choice depends on static routing rules, the entries that
are registered in the system routing table. Static routes to
specific hosts, networks, or the default gateway are set up
automatically according to the IP configuration of all the
airOS Configuration Interfaces.
Note: You can also manually add static routes (refer
to âStatic Routesâ on page 43 for details).
Refresh To update the information, click Refresh.
IPv4 Routes
Bridge Table
Destination Displays the IP address of the destination
network or host.
(Available in Bridge mode only.) The table displays the
entries in the system Bridge Table.
Gateway Displays the IP address of the appropriate
gateway.
Netmask Displays the netmask of the destination
network: 255.255.255.255 for a destination host or 0.0.0.0
for the default route.
Interface Displays the interface that will receive the
packets for that route.
Bridge The name of the bridge.
MAC Address The network device identified by its MAC
address.
12
Note: The default route is the route that is used
when no other routes for the destination are found
in the routing table.
Ubiquiti Networks, Inc.
airOSÂŽ v5.6 User Guide
Chapter 2: Main
IPv6 Routes
Port Forward
For IPv6 addresses, the airOS Configuration Interface
supports â::â (double-colon) notation, which substitutes
â::â for a contiguous sequence of 16-bit blocks set to zero.
Here is an example: 2001:db8::1
(Available in Router or SOHO Router mode only.) Port
forwarding allows you to connect to a specific service such
as an FTP server or web server. Port forwarding creates a
transparent tunnel through a firewall/NAT, granting access
from the WAN side to the specific network service running
on the LAN side.
If written out, the IPv6 address becomes:
2001:db8:0000:0000:0000:0000:0000:0001
Note: You can also manually add static routes (refer
to âIPv6 Static Routesâ on page 44 for details).
Destination Displays the IP address of the destination
network or host.
Gateway Displays the IP address of the appropriate
gateway.
Refresh To update the information, click Refresh.
Port Forward Rules Lists active port forward entries in
the PREROUTING chain of the standard iptables nat table,
while the device is operating in Router or SOHO Router
mode.
Firewall
Refresh To update the information, click Refresh.
When the firewall is enabled on the Network page, this
option is available. By default, there are no firewall rules.
Configure port forwarding rules on the Network page. See
âTraffic Shapingâ on page 44 for additional details.
If the device is operating in Bridge mode, the table lists
active firewall entries in the FIREWALL chain of the
standard ebtables filter table.
DHCP Leases
Interface Displays the interface that will receive the
packets for that route.
If the device is operating in Router or SOHO Router mode,
the table lists active firewall entries in the FIREWALL chain
of the standard iptables filter table.
Firewall Rules IP and MAC level access control and
packet filtering in airOS are implemented using an
ebtables (bridging) or iptables (routing) firewall that
protects the resources of a private network from outside
threats by preventing unauthorized access and filtering
specified types of network communication.
Refresh To update the information, click Refresh.
Configure firewall rules on the Network page. See
âFirewallâ on page 42 or âIPv6 Firewallâ on page
43 for additional details.
Ubiquiti Networks, Inc.
(Available in Router or SOHO Router mode only with the
DHCP server feature enabled.) Displays the current status
of the IP addresses assigned by the deviceâs DHCP server
to its local DHCP clients.
MAC Address Displays the clientâs MAC address.
IP Address Displays the clientâs IP address.
Remaining Lease Displays the remaining time of the
leased IP address assigned by the DHCP server.
Hostname Displays the device name of the client.
Refresh To update the information, click Refresh.
13
Chapter 2: Main
airOSÂŽ v5.6 User Guide
GPS Details (GPS Series Only)
GPS Details (available on GPS Series devices only) displays
GPS Satellite details and Signal quality.
Refresh To update the information, click Refresh.
Log
When logging is enabled (see âSystem Logâ on page
52 to enable logging), this option lists all registered
system events. By default, logging is not enabled.
Clear To delete all entries in the system log, click Clear.
Refresh To update the log content, click Refresh.
14
Ubiquiti Networks, Inc.
airOSÂŽ v5.6 User Guide
Chapter 3: Ubiquiti Logo
The Ubiquiti logo page displays settings to enable, launch,
and change settings for Ubiquitiâs proprietary features,
including:
â˘ airMAXÂŽ Provides superior wireless performance, more
clients per Access Point (AP), and lower latency under
load.
â˘ airSelectÂŽ Dynamically changes the wireless channel to
avoid interference.
â˘ airViewÂŽ Ubiquitiâs spectrum analyzer.
â˘ airSyncâ˘ Synchronizes transmissions by GPS Series
devices to eliminate co-location transmit interference.
Note: By default, indoor products, such as the
airRouter, do not display the Ubiquiti logo page.
However, you can enable the Ubiquiti logo
page through System > Miscellaneous > airMAX
Technology Features. For more information, see
âMiscellaneousâ on page 55.
Change To save or test your changes, click Change.
A new message appears. You have three options:
â˘ Apply To immediately save your changes, click Apply.
â˘ Test To try the changes without saving them, click
Test. To keep the changes, click Apply. If you do not
click Apply within 180 seconds (the countdown is
displayed), the device times out and resumes its earlier
configuration.
â˘ Discard To cancel your changes, click Discard.
Ubiquiti Networks, Inc.
Chapter 3: Ubiquiti Logo
airMAX Settings
airMAX is Ubiquitiâs proprietary Time Division Multiple
Access (TDMA) polling technology. airMAX improves
overall performance in Point-to-Point (PtP) and
Point-to-MultiPoint (PtMP) installations and noisy
environments because it reduces latency, increases
throughput, and offers better tolerance against
interference. Because of its advantages, airMAX also
increases the maximum possible number of users that can
associate with an AP that uses airMAX.
airMAX assigns time slots for each device communication
to avoid the âhidden nodeâ problem, which occurs when
a node is visible from a wireless AP, but not from other
nodes communicating with the originating AP.
airMAX also features advanced Quality of Service (QoS)
autodetection settings. For airMAX to classify and
differentiate types of traffic when applying QoS rules,
the traffic must have a special value within the TOS
(Type of Service) range and set in the IP Header DSCP
(Differentiated Services Code Point) field. The original
software or hardware device is responsible for setting this
value; airMAX will prioritize traffic only if this value is set.
There are four WME (Wireless Multimedia Enhancements)
categories, which range from lowest to highest priority in
this order:
â˘ Best Effort
â˘ Background
â˘ Video
â˘ Voice
15
Chapter 3: Ubiquiti Logo
airOSÂŽ v5.6 User Guide
By default, all traffic is classified as Best Effort, so no
prioritization is applied. The categories can be defined
using the following values:
802.1p Class of Service
TOS Range
DSCP Range WME Category
0 â Best Effort
0x00-0x1f
0-7
Best Effort
1 â Background
0x20-0x3f
8-15
Background
2 â Spare
0x40-0x5f
16-23
Background
3 â Excellent Effort
0x60-0x7f
24-25, 28-31
Best Effort
4 â Controlled Load
0x80-0x9f
32-39
Video
5 â Video
(<100 ms latency)
0xa0-0xbf
40-45
Video
6 â Voice
(<10 ms latency)
0x68, 0xb8,
0xc0-0xdf
26-27, 46-47,
48-55
Voice
0xe0-0xff
56-63
Voice
7 â Network Control
For compatibility, legacy or 802.11 a/b/g devices should use
legacy firmware with airMAX support (such as airOS firmware
v4.0). Legacy clients can only work as airMAX clients with
the M Series device acting as an airMAX AP.
Note: To support legacy clients using airMAX, the M
Series device must run airOS v5.5 or above.
airMAX Settings include:
Note: If you use Long Range PtP Link Mode, then
the Auto Adjust setting on the Advanced page is
not available.
If your device has multiple stations or clients, do not
use Long Range PtP Link Mode; instead, enable the Auto
Adjust setting on the Advanced page (see âAuto Adjustâ
on page 46 for additional details).
â˘ airMAX Priority (Available in Station mode only.) It
defines the number of time slots (or amount of airtime)
assigned to each client. By default the AP gives all active
clients the same amount of time. However, if the clients
are configured with different priorities, the AP will give
clients more or less time, depending on the priority.
Note: airMAX Priority only functions when
multiple clients have it enabled.
airMAX Priority options include:
- High 4 time slots (4:1 ratio)
- Medium 3 time slots (3:1 ratio)
- Low 2 time slots (2:1 ratio)
- None 1 time slot (Default setting for clients; 1:1 ratio)
â˘ airMAX (Available in Access Point or AP-Repeater
mode only.) If airMAX is enabled, the device operates
in airMAX mode and only accepts connections from
airMAX devices.
Note: If airMAX is enabled, you cannot connect
standard Wi-Fi devices, such as laptops, tablets,
or smartphones, to the AP.
If the device is in Station mode under Wireless > Wireless
Mode, the device will automatically enable airMAX when
it is connecting to an airMAX AP.
â˘ Long Range PtP Link Mode (Available in Access
Point or AP-Repeater mode only.) Acknowledgment
(ACK) timeout settings are limited by device hardware
specifications.
Note: Enable Long Range PtP Link Mode for PtP
OLQNVRQO\
If the following two conditions apply to your device:
â˘ Connects to a single station or client (a PtP situation)
Clients with a higher priority have access to more of the
APâs airtime, providing higher possible throughput and
lower latency when sharing with other active clients.
For example, if there are 3 clients, 1 set to None, 1 set to
Medium, and 1 set to High, the None client will get 1 time
slot, the Medium client will get 3 time slots, and the High
client will get 4 time slots.
airSelect
Note: If you enable airSelect, then airSync is not
available.
(Available in Access Point mode only.) airSelect is a
technology that avoids interference and increases
throughput. It dynamically changes the wireless channel
by periodically hopping to the least used channel in the
Frequency List (user-defined) within a designated time
interval (user-defined in milliseconds). airSelect tracks
interference levels on each channel used, hopping more
frequently to those with the least amount of interference.
airSelect options include:
â˘ The actual link distance exceeds hardware ACK
timeout limits:
â˘ 27 km or 17 miles (40 MHz mode)
â˘ 51 km or 32 miles (20 MHz mode)
then select Long Range PtP Link Mode.
16
Ubiquiti Networks, Inc.
airOSÂŽ v5.6 User Guide
Chapter 3: Ubiquiti Logo
â˘ airSelect Check the box to enable airSelect. When
airSelect is enabled, the AP and all associated clients
quickly hop between frequencies to avoid interference.
â˘ Do NOT warn me about this in the future Check the
box to bypass this window in future launches of the
airView Spectrum Analyzer.
â˘ Frequency List Available when airSelect is enabled.
Click Edit to select the frequencies that the AP will
use for airSelect. Available frequencies are devicedependent.
â˘ Launch airView Click Launch airView to download the
Java Network Launch Protocol (jnlp) file and complete
the launch of airView.
â˘ Hop Interval Available when airSelect is enabled. The
duration (in milliseconds) that the AP will stay on one
frequency before moving to the next. The default value
is 3000 milliseconds (ms).
â˘ Announce Count Available when airSelect is
enabled. The number of times between hops the
AP will announce the next hop information (such as
frequency) to clients. For example, if the Hop Interval
is set to 3000PVÂŠ GHIDXOW ÂŠDQGÂŠWKHÂŠAnnounce Count is
set to 30 (default), then every 100 ms the AP will send
an announcement with upcoming hop information
WRWKHÂŠFOLHQWVÂŠ7KHÂŠODUJHUÂŠWKHÂŠWLPHÂŠSHULRGÂŠEHWZHHQÂŠWKHÂŠ
Announce Count and Hop Interval, the higher the risk
of timing drift (hops not being synchronized), so we
recommend that you keep the defaults or configure
the AP to send an announcement every 100 ms (set
WKHAnnounce Count to 1/100th of the Hop Interval).
airView
Use the airView Spectrum Analyzer to analyze the noise
environment of the radio spectrum and intelligently select
the optimal frequency to install a PtP airMAX link.
airView options include:
Main View
â˘ airView Port Defines the TCP port used by airView on
the device. The default port is 18888.
â˘ Launch airView There are two system requirements for
the airView Spectrum Analyzer:
â˘ Your system is connected to the device via Ethernet.
Launching airView will terminate all wireless
connections on the device.
â˘ Java Runtime Environment 1.6 (or above) is required
on your client machine to use airView.
Click Launch airView to use the airView Spectrum
Analyzer. On first use, the following window appears.
Device Displays the device name, MAC (Media Access
Control) address, and IP address of the device running
airView.
Total RF Frames Displays the total number of Radio
Frequency (RF) frames gathered since the start of the
airView session or since the Reset All Data button was last
clicked.
FPS Displays the total number of frames per second (FPS)
gathered since the start of the airView session or since
the Reset All Data button was last clicked. The wider the
interval amplitude, the fewer the FPS will be gathered.
Reset All Data Click to reset all gathered data. Use this
option to analyze the spectrum for another location or
address.
File Menu
Click Exit to end the airView session.
Ubiquiti Networks, Inc.
17
Chapter 3: Ubiquiti Logo
View Menu
airOSÂŽ v5.6 User Guide
Charts
Enable Chart Panel 1 (top) Displays the Waterfall or
Channel Usage chart in Chart Panel 1, depending on
which option you have selected in Preferences. This
time-based graph shows the aggregate energy collected
or channel usage for each frequency since the start of the
airView session.
Enable Chart Panel 2 (middle) Displays the Waveform
chart in Chart Panel 2. This time-based graph shows the RF
signature of the noise environment since the start of the
airView session. The energy color designates its amplitude.
Cooler colors represent lower energy levels (with blue
representing the lowest levels) in that frequency bin, and
warmer colors (yellow, orange, or red) represent higher
energy levels in that frequency bin.
Enable Chart Panel 3 (bottom) Displays the Real-time
chart (traditional spectrum analyzer) in Chart Panel 3.
Energy (in dBm) is shown in real time as a function of
frequency.
Note: Energy is the power ratio in decibels (dB) of
the measured power referenced to one milliwatt
(mW).
Clear All Markers Resets all previously assigned
markers. Markers are assigned by clicking a point, which
corresponds with a frequency on the Real-time chart.
Preferences Changes airView settings, such as enabling
or disabling charts and traces, or specifying the frequency
interval.
Preferences
Select View > Preferences to display the Preferences airView Spectrum Analyzer window.
Enable top chart Check the box to enable the top chart.
Select the desired chart to display in the top chart panel
on the main view. There are two options:
â˘ Waterfall This time-based graph shows the aggregate
energy collected for each frequency since the start
of the airView session. The energy color designates
its amplitude. Cooler colors represent lower energy
levels (with blue representing the lowest levels)
in that frequency bin, and warmer colors (yellow,
orange, or red) represent higher energy levels in that
IUHTXHQF\ELQ
The Waterfall Viewâs legend (top-right corner) provides
a numerical guide associating the various colors to
power levels (in dBm). The low end of that legend (left)
is always adjusted to the calculated noise floor, and the
high end (right) is set to the highest detected power
level since the start of the airView session.
â˘ Channel Usage For each Wi-Fi channel, a bar displays
a percentage showing the relative âcrowdednessâ of
that specific channel. To calculate this percentage, the
airView Spectrum Analyzer analyzes both the popularity
and strength of RF energy in that channel since the start
of an airView session.
Enable Waveform chart (middle) Check the box to
enable the middle chart. This time-based graph shows
the RF signature of the noise environment since the
start of the airView session. The energy color designates
its amplitude. Cooler colors represent lower energy
levels (with blue representing the lowest levels) in that
frequency bin, and warmer colors (yellow, orange, or red)
represent higher energy levels in that frequency bin.
18
Ubiquiti Networks, Inc.
airOSÂŽ v5.6 User Guide
The spectral view over time will display the steady-state RF
energy signature of a given environment.
Enable Real-time chart (bottom) Check the box to
enable the bottom chart. This graph displays a traditional
spectrum analyzer in which energy (in dBm) is shown in
real time as a function of frequency. There are three traces
in this view:
â˘ Current (Yellow) Shows the real-time energy seen by
the device as a function of frequency.
â˘ Average (Green) Shows the running average energy
across frequency.
â˘ Maximum (Blue) Shows updates and maximum power
levels across frequency.
Realtime Traces
Chapter 3: Ubiquiti Logo
Maximum Power Levels Trace Check the Enable box to
enable the maximum power trace. When enabled, the
maximum power trace is represented by the blue area on
the Real-time chart, which displays the maximum received
power level data since the start of the airView session. To
enable a shaded blue area, check the Shaded Area box.
To display only a blue outline without the shaded area,
uncheck the Shaded Area box.
Frequency Range Select the amplitude of the
frequency interval to be scanned from the Frequency
Range drop-down list. Available frequencies are devicedependent. There are pre-defined ranges for the most
popular bands. You can enter a custom range; select
Custom Range from the Frequency Range drop-down list
and enter the desired values in the Start and End fields.
Help
Click About to view the version and build number of the
airView Spectrum Analyzer.
airSync (GPS Series Only)
Note: If you enable airSync, then airSelect is not
available.
(Available in Access Point mode only.) airSync (available on
GPS Series devices only) synchronizes airMAX APs with a
satellite reference timing signal. When enabled, airSync
eliminates receive (RX) errors due to co-location transmit
interference.
Note: To use airSync, all Stations must run airOS
v5.5 or higher; otherwise, they cannot connect to
any of the APs.
We recommend the following guidelines:
â˘ Adjacent sectors should use different frequencies.
â˘ Back-to-back sectors can use the same frequency.
The following settings apply only to the Real-time chart:
Current Real-time Trace Check the Enable box to enable
the real-time trace. When enabled, the yellow outline on
the Real-time chart represents the real-time power level of
each frequency. The refresh speed depends on the FPS.
Averages Trace Check the Enable box to enable the
averages trace. When enabled, the averages trace is
represented by the green area on the Real-time chart,
which displays the average received power level data
since the start of the airView session. To enable a shaded
green area, check the Shaded Area box. To display only
a green outline without the shaded area, uncheck the
Shaded Area box.
Ubiquiti Networks, Inc.
â˘ Do not use the same frequency on ALL of your
co-located APs. Some of your co-located APs may be
able to use the same frequency, depending on the
scenario. See the following examples: Four APs and
Two APs.
â˘ The number of frequencies you should use depends on
the number of APs you have on a single tower because a
client can get confused if it receives signals on the same
frequency from two different APs.
â˘ If you are using more than one frequency, ensure that
you have 20 MHz separation between the frequency
band edges. For example: if frequency range A ends at
5815 MHz, then frequency range B should start at 5835
MHz or higher.
19
Chapter 3: Ubiquiti Logo
airOSÂŽ v5.6 User Guide
We have the following examples:
To sync multiple APs, these are the requirements:
â˘ Four APs Use two different frequencies. Set the same
frequency on each back-to-back pair of APs (this is the
ABAB channel design). For example, a client is located
equidistant from two APs (one set to frequency A and
one set to frequency B). The client will only receive
signals from the AP that shares its frequency.
â˘ The master AP has IP connectivity (specifically UDP) to
the slave APs.
â˘ All APs have an active GPS signal.
â˘ You have configured the transmit and receive durations
on the master AP.
After you configure these durations, or slots, on the
master AP, they are passed along to all slave APs. The same
transmit and receive durations allow each AP to determine
when to start transmitting, and when to start receiving.
Slots are configured in Îźs (microseconds) and specify the
period of time the AP will transmit (Down Slot), and receive
(Up Slot). The Down Slot sets the amount of time for client
users to download, while the Up Slot sets the amount of
time for client users to upload.
Three APs Set a different frequency on each AP (this is
the ABC channel design). For example, a client is located
equidistant from two APs (one set to frequency A and
one set to frequency B). The client will only receive signals
from the AP that shares its frequency. A different client is
located equidistant from a different pair of APs (one set
to frequency B and one set to frequency C). This client will
only receive signals from the AP that shares its frequency.
You can think of the Down Slot period and Up Slot period
as a ratio. If the Down Slot is set to 4000 Îźs, and the Up Slot
is set to 2000 Îźs, the AP allocates 66% [4000/(4000+2000)]
of its time providing clientsâ download slots, while the AP
allocates the remaining 33% to clientsâ upload slots.
Some usage scenarios may require use of the Timing
Override feature, depending on usersâ upload and
download traffic. If an AP groupâs users will primarily be
downloading, increase the ratio of Down Slots to Up Slots.
Similarly, if an AP group has more business users and
needs higher upload speeds, use a more even Down Slot/
Up Slot ratio. Depending on traffic patterns, you may need
to adjust the Down Slot/Up Slot ratio as needed.
airSync options include:
â˘ Enable airSync Check the box to enable airSync.
â˘ Two APs Set the same frequency on both APs located
back to back (this is the AA channel design).
â˘ Mode Available when airSync is enabled. Select Master
or Slave depending on which device is configured in
Master mode and which devices are configured in Slave
mode. The device in Master mode synchronizes with all
connected peers in Slave mode.
â˘ Port Available when airSync is enabled. By default, the
port is set to 64250 but you can change the value in the
field.
20
Ubiquiti Networks, Inc.
airOSÂŽ v5.6 User Guide
Chapter 3: Ubiquiti Logo
â˘ Timing Override (Master) Available when airSync
is enabled on the Master AP. Check the box to enable
Timing Override. Uncheck the box to disable Timing
Override and restore default settings, which vary
depending on the channel bandwidth:
Channel Bandwidth
Down Slot
Up Slot
40 MHz
2000 Îźs
2000 Îźs
30 MHz
4000 Îźs
4000 Îźs
20 MHz
4000 Îźs
4000 Îźs
10 MHz
4000 Îźs
4000 Îźs
8 MHz
4000 Îźs
4000 Îźs
5 MHz
8000 Îźs
8000 Îźs
â˘ Master IP (Slave) Available when airSync is enabled on
the slave AP. Enter the IP address of the master AP.
Ubiquiti Networks, Inc.
21
Chapter 3: Ubiquiti Logo
airOSÂŽ v5.6 User Guide
22
Ubiquiti Networks, Inc.
airOSÂŽ v5.6 User Guide
Chapter 4: Wireless
Chapter 4: Wireless
A new message appears. You have three options:
The Wireless page contains everything needed to set up
the wireless part of the link. This includes SSID, channel
and frequency settings, device mode, data rates, and
wireless security.
â˘ Test To try the changes without saving them, click
Test. To keep the changes, click Apply. If you do not
click Apply within 180 seconds (the countdown is
displayed), the device times out and resumes its earlier
configuration.
â˘ Apply To immediately save your changes, click Apply.
â˘ Discard To cancel your changes, click Discard.
Basic Wireless Settings
In this section, configure the basic wireless settings, such
as wireless mode, wireless network name (SSID), country
code, 802.11 mode, output power, and data rates.
Wireless Mode Specify the Wireless Mode of the
device. The mode depends on the network topology
requirements. airOS supports the following modes:
Change To save or test your changes, click Change.
â˘ Station If you have a client device to connect to an
AP, configure the client device as Station mode. The
client device acts as the subscriber station while it is
connecting to the AP. The SSID of the AP is used, and all
the traffic to and from the network devices connected to
the Ethernet interface is forwarded.
Note: If WDS (Transparent Bridge Mode) is
disabled, the radio uses arpnat, which results
in non-transparent bridging. To have a fully
transparent bridge, select Station and then
enable WDS (Transparent Bridge Mode).
Ubiquiti Networks, Inc.
23
Chapter 4: Wireless
airOSÂŽ v5.6 User Guide
Auto (Available in AP-Repeater mode only.) Check the
Auto box to automatically establish WDS connections
between APs in AP-Repeater mode. If the Auto option
is enabled, the device will choose WDS Peers (APs in
AP-Repeater mode) according to the SSID setting.
Note: All APs in AP-Repeater mode (WDS Peers)
must operate on the same frequency channel, use
the same channel spectrum width, and share the
same security settings.
â˘ Access Point If you have a single device to act as
an AP, configure it as Access Point mode. The device
functions as an AP that connects multiple client devices.
If you have multiple APs repeating signals where
Ethernet connections are not readily available, then use
AP-Repeater mode.
Note: For Access Point (WDS) mode, select Access
Point and then enable WDS (Transparent Bridge
Mode).
â˘ AP-Repeater If you have multiple APs, configure them
as AP-Repeater mode to create a wireless network
infrastructure, WDS. If the Auto option is enabled, all APs
using the same wireless mode (AP-Repeater) and SSID
automatically establish the WDS connections. (Client
devices can still connect to APs in AP-Repeater mode.)
Note: For AP-Repeater mode, the WPAâ˘/WPA2â˘
security methods will not work; instead, use
none or the WEP security method (this may
compromise the security of your network).
You still have the option of using RADIUS MAC
authentication and MAC ACL.
WPA or WPA2 requires different roles on AP
configuration (authenticator or supplicant).
WDS Peers (Available in AP-Repeater mode only.) If you
do not enable the Auto option, then specify the APs in
AP-Repeater mode. Enter the MAC address of each AP
in each WDS Peers field. One MAC address should be
specified for a Point-to-Point (PtP) connection use case.
You can specify up to six WDS Peers for a Point-to-MultiPoint (PtMP) connection use case.
SSID If the device is operating in Access Point or
AP-Repeater mode, specify the wireless network name or
SSID (Service Set Identifier) used to identify your WLAN.
All the client devices within range will receive broadcast
messages from the AP advertising this SSID.
If the device is operating in Station mode, specify the
SSID of the AP the device is associated with. There can be
several APs with an identical SSID.
Select (Available in Station mode only.) To display the list
of available APs, click Select.
The Site Survey tool will search for available wireless
networks in range on all supported channels and allow
you to select one for association. In case the selected
network uses encryption, youâll need to configure security
on the Wireless page.
WDS (Transparent Bridge Mode) (Available in Access
Point or Station mode only.) In most cases, we recommend
WKDWÂŠ\RXÂŠXVHÂŠ:'6ÂŠEHFDXVHÂŠLWÂŠHQDEOHVÂŠWUDQVSDUHQWÂŠ/D\HUÂŠ
traffic. To use WDS with Station or Access Point mode,
check the Enable box.
â˘ Lock to AP Select the AP from the list. Click Lock to AP
to allow the station to always maintain a connection to
an AP with a specific MAC address.
The WDS protocol is not defined as a standard, so there
may be compatibility issues between equipment from
different vendors.
â˘ Scan Click Scan to refresh the list of available wireless
networks.
â˘ Station (WDS) Station (WDS) mode should be used if
the device is connecting to an AP in Access Point (WDS)
mode.
â˘ Access Point (WDS) Access Point (WDS) mode allows
/D\HUÂŠEULGJLQJÂŠZLWKÂŠGHYLFHVÂŠLQÂŠStation (WDS) mode.
Note: If you connect devices running in Station
(WDS) mode to a device running in Access Point
(WDS) mode, then all security methods (including
WPA/WPA2 encryption) are available and work
properly.
24
â˘ Select Select the AP from the list and click Select for
association.
You can change the list of Scanned Frequencies for the
Site Survey using the Frequency List option if it is enabled.
Lock to AP MAC (Available in Station mode only.) This
allows the station to always maintain a connection
to an AP with a specific MAC address. This is useful as
sometimes there can be multiple APs using the same SSID.
Enter a MAC address in the Lock to AP MAC field, and the
station will lock to the AP with this specific MAC address
and not roam between several APs with the same SSID.
Ubiquiti Networks, Inc.
airOSÂŽ v5.6 User Guide
Chapter 4: Wireless
Hide SSID (Available in Access Point or AP-Repeater
mode only.) When Hide SSID is enabled, the SSID (wireless
network name) will not be broadcast to wireless stations.
Channel Width Displays the spectral width of the radio
channel. You can use this option to control the bandwidth
consumed by your link.
Country Code Each country has their own power level
and frequency regulations. To ensure the device operates
under the necessary regulatory compliance rules, you must
select the country where your device will be used. The IEEE
802.11 mode, channel and frequency settings, and output
power limits will be tuned according to the regulations of
the selected country.
Using higher bandwidth increases throughput. Using
lower bandwidth:
IEEE 802.11 Mode This is the radio standard used for
operation of your device. 802.11b, 802.11a, and 802.11g
are older standards, while 802.11n is a newer standard
that provides higher capacity and better performance.
Options include:
â˘ A/N mixed Connects to an 802.11a or 802.11n network.
This mode offers better compatibility. A/N mixed mode is
selected by default on the following devices:
- M900 Series devices
- M3 Series devices
- M365 Series devices
- M5 Series devices
â˘ B/G/N mixed Connects to an 802.11b, 802.11g, or
802.11n network. This mode offers better compatibility.
B/G/N mixed mode is selected by default on the
following devices:
- M2 Series devices
DFS 2QO\ÂŠDSSOLFDEOHÂŠWRÂŠVSHFLILFÂŠ*+]ÂŠGHYLFHVÂŠFRQILJXUHGÂŠ
with specific Country Codes.) Radar systems use specific
IUHTXHQFLHVÂŠLQÂŠWKHÂŠ*+]ÂŠUDQJHÂŠ')6ÂŠ '\QDPLFÂŠ)UHTXHQF\ÂŠ
Selection) technology avoids interference with radar
signals. Depending on the regulations of the country
selected in the Country Code option:
â˘ 6SHFLILFÂŠ*+]ÂŠGHYLFHVÂŠPD\ÂŠEHÂŠDOORZHGÂŠXVHÂŠRIÂŠ')6ÂŠ
IUHTXHQFLHVÂŠLQÂŠWKHÂŠ81,,ĂľÂŠEDQGÂŠ ÂŠĂľÂŠÂŠ*+] ÂŠLIÂŠWKH\ÂŠ
use DFS technology.
â˘ The DFS option may be available in airOS. If available,
then you can use this option to enable or disable DFS
functionality.
Before your device starts using a DFS frequency, it
PD\ÂŠORVHÂŠFRQQHFWLRQÂŠIRUÂŠÂŠRUÂŠPLQXWHVÂŠGXULQJÂŠWKHÂŠ
Channel Availability Check (CAC) time, depending on
the frequency. (In particular, weather radar frequencies,
Ăľ0+]ÂŠPD\ÂŠKDYHÂŠORQJÂŠZDLWÂŠWLPHV ÂŠ
If your device detects a radar on that frequency, it adds
this frequency to a blacklist for 30 minutes. If only one
frequency is on the Frequency List, then the device will
lose connection for 30-40 minutes after it detects the
radar. Also, any radio operating with Equivalent Isotropic
Radiated Power (EIRP) > 200 mW will lose connection for
30 minutes if it detects a radar.
â˘ Reduces throughput proportional to the reduction in
FKDQQHOÂŠVL]HÂŠ)RUÂŠH[DPSOHÂŠDVÂŠÂŠ0+]ÂŠLQFUHDVHVÂŠSRVVLEOHÂŠ
VSHHGVÂŠE\ÂŠ[ÂŠKDOIÂŠVSHFWUXPÂŠFKDQQHOÂŠ ÂŠ0+] ÂŠGHFUHDVHVÂŠ
possible speeds by 2x.
â˘ Increases the number of available, non-overlapping
channels, so networks can scale better.
â˘ Increases the Power Spectral Density (PSD) of the
channel, so you can increase the link distance â more
robust links over long distances.
Available channel widths are device-specific. Supported
wireless channel spectrum widths include:
â˘ 3 MHz 7KHÂŠFKDQQHOÂŠVSHFWUXPÂŠZLWKÂŠWKHÂŠZLGWKÂŠRIÂŠÂŠ0+]
â˘ 5 MHz 7KHÂŠFKDQQHOÂŠVSHFWUXPÂŠZLWKÂŠWKHÂŠZLGWKÂŠRIÂŠÂŠ0+]ÂŠ
(known as Quarter-Rate mode).
â˘ 7 MHz 7KHÂŠFKDQQHOÂŠVSHFWUXPÂŠZLWKÂŠWKHÂŠZLGWKÂŠRIÂŠ0+]
â˘ 8 MHz 7KHÂŠFKDQQHOÂŠVSHFWUXPÂŠZLWKÂŠWKHÂŠZLGWKÂŠRIÂŠ0+]
â˘ 10 MHz The channel spectrum with the width of
0+]ÂŠ NQRZQÂŠDVÂŠ+DOIĂľ5DWHÂŠPRGH
â˘ 14 MHz The channel spectrum with the width of
0+]
â˘ 20 MHz The standard channel spectrum width of
0+]ÂŠ VHOHFWHGÂŠE\ÂŠGHIDXOW
Note: To connect standard Wi-Fi devices that use
WKHÂŠÂŠ*+]ÂŠEDQGÂŠHQVXUHÂŠWKDWÂŠ20 MHz is selected.
â˘ 25 MHz The channel spectrum with the width of
0+]
â˘ 28 MHz The channel spectrum with the width of
0+]
â˘ 30 MHz The channel spectrum with the width of
0+]ÂŠ
â˘ 40 MHz The channel spectrum with the width of
0+]
â˘ Auto 20/40 MHz (Available in Station mode only.)
Offers better compatibility.
Channel Shifting 1RWÂŠDYDLODEOHÂŠIRUÂŠÂŠ*+]ÂŠSURGXFWV ÂŠ
Enables special channels with a frequency offset regarding
standard 802.11b/g/n channels. This is a proprietary
feature developed by Ubiquiti Networks. Channel shifting
uses non-standard (non-802.11) channels offset from the
standard channels. All the channels can be shifted by
0+]ÂŠ LQÂŠEJQ ÂŠIURPÂŠWKHÂŠGHIDXOWÂŠFHQWUDOÂŠFKDQQHOÂŠ
frequency.
Note: Channel Shifting is not compatible with legacy
products.
The benefits of Channel Shifting include private
networking and inherent security, so your network is less
likely to be detected by other Wi-Fi devices.
Ubiquiti Networks, Inc.
25
Chapter 4: Wireless
Frequency, MHz The default, auto, allows the device
to automatically select the frequency. You can specify a
frequency from the drop-down list. You can change the list
using the Frequency List option if it is enabled.
,IÂŠ')6ÂŠIUHTXHQFLHVÂŠLQÂŠWKHÂŠ81,,ĂľÂŠEDQGÂŠ ÂŠĂľÂŠÂŠ*+] ÂŠ
should be available for your device but are not displayed
in the drop-down list, then the DFS frequencies are locked.
For information on how to unlock the DFS frequencies,
refer to this option, âUNII-2 Bandâ on page 55.
airOSÂŽ v5.6 User Guide
Calculate EIRP Limit (Not applicable to the
NanoStationM900 loco.) Mandatory for all US products
with fixed antennas, this option should remain enabled
so it forces the transmit output power to comply with the
regulations of the selected country. If enabled, you cannot
set EIRP above the amount allowed per regulatory domain
(different maximum output power levels and antenna
gains are allowed for each IEEE 802.11b/g/n regulatory
domain or country).
Extension Channel (Available in Access Point or
AP-Repeater mode only with 40 MHz channel width
HQDEOHG ÂŠ$ÂŠÂŠ0+]ÂŠFKDQQHOÂŠLVÂŠWZRÂŠÂŠ0+]ÂŠFKDQQHOVÂŠ
bonded together. The Extension Channel tells the radio
to append an additional channel either above or below
the existing standard channel. For example, if you select
5805 MHzÂŠ ÂŠ0+]ÂŠFKDQQHO ÂŠDQGÂŠLower, the radio will use
ÂŠWRÂŠÂŠ0+] ÂŠÂŠ ÂŠWRÂŠÂŠ0+] ÂŠEXWÂŠLIÂŠ\RXÂŠVHOHFWÂŠ
5805 MHzÂŠ ÂŠ0+]ÂŠFKDQQHO ÂŠDQGÂŠUpper, the radio will use
ÂŠWRÂŠÂŠ0+] ÂŠÂŠ ÂŠWRÂŠÂŠ0+]
To disable EIRP Limit calculation, you must enable the
Installer EIRP Control setting on the Advanced page.
Frequency List, MHz (Available in Access Point or
AP-Repeater mode only.) Multiple frequencies are available
to avoid interference between nearby APs. The frequency
list varies depending on the selected Country Code, IEEE
802.11 Mode, Channel Width, and Channel Shifting options.
This restricts AP operation to the selected frequencies
when the auto option is enabled.
â˘ airGridM2/M2 HP 6HOHFWÂŠWKHÂŠVL]HÂŠRIÂŠWKHÂŠJULGÂŠUHIOHFWRUÂŠ
11x14 Âą 16dBi or 17x24 â 20 dBi. For no gain, selectÂŠ
Not specified. If you are not using a grid reflector, thenÂŠ
keep the default, Feed only - 3 dBi.
Once enabled, click Edit to open the Frequency List
window.
Antenna (Available for devices with multiple antenna
gain options.) Devices that have internal antennas do not
offer the Antenna field; however, their default settings (if
applicable) are still listed for your reference.
Note: NanoBeam with dish antenna models are
now renamed as PowerBeam.
)ROORZÂŠWKHÂŠLQVWUXFWLRQVÂŠIRUÂŠ\RXUÂŠ0ÂŠPRGHOGHYLFH
â˘ airGridM5/M5 HP 6HOHFWÂŠWKHÂŠVL]HÂŠRIÂŠWKHÂŠJULGÂŠUHIOHFWRUÂŠ
11x14 â 23dBi, 17x24 - 28 dBi (M5), or 17x24 â 27 dBiÂŤ
0ÂŠ+3 ÂŠ)RUÂŠQRÂŠJDLQÂŠVHOHFWÂŠNot specified. If you are notÂŠ
using a grid reflector, then keep the default, Feed only 3 dBi.
â˘ LiteStationM5 Select the appropriate option,ÂŠ
Horizontal (6 dBi) or Vertical (6 dBi). The default isÂŠ
Horizontal.
â˘ NanoBeamM5 16 The default is 16 dBi.
â˘ NanoBeamM5 19 The default is 19 dBi.
â˘ NanoBridgeM2 If you are not using a dish reflector,ÂŠ
then select Feed only - 3 dBi. Otherwise, keep theÂŠ
default, 18 dBi.
Select the frequencies and click OK, or click Close to close
the window without any selections.
Frequency Scan List, MHz (Available in Station mode
only.) This restricts scanning to only the selected
frequencies. The benefits are faster scanning as well as
filtering out unwanted APs in the results. The Site Survey
tool will look for APs in selected frequencies only. Once
enabled, click Edit to open the Frequency List window.
â˘ NanoBridgeM3/M365 The default is 19 dBi.
â˘ NanoBridgeM5 6HOHFWÂŠWKHÂŠVL]HÂŠRIÂŠWKHÂŠGLVKÂŠUHIOHFWRUÂŠ
300 - 22 dBi or 400 - 25 dBi. For no gain, select NotÂŤ
specified. The default is Feed only - 3 dBi. If you are notÂŠ
using a grid reflector, then keep the default, Feed only 3 dBi.
â˘ NanoBridgeM900 The default is 13 dBi.
â˘ NanoStationM2 The default is 11 dBi.
â˘ NanoStationM3/M365 The default is 12 dBi.
â˘ NanoStationM5/M6 The default is 16 dBi.
â˘ NanoStationM900 The default is Internal (2x2) for
ÂŠG%L
â˘ NanoStationORFRM2 The default is 8 dBi.
â˘ NanoStationORFRM5 The default is 13 dBi.
Select the frequencies that you want to scan and click OK,
or click Close to close the window without any selections.
26
Ubiquiti Networks, Inc.
airOSÂŽ v5.6 User Guide
â˘ NanoStationORFRM900 Select the appropriate option:ÂŠ
Internal (2x2) for 8 dBi, External (1x1), or External +ÂŤ
Internal (2x2). The external RP-SMA maps to chain 0,ÂŠ
ZKLFKÂŠLVÂŠWKHÂŠKRUL]RQWDOÂŠSRODULW\ÂŠLQWHUQDOO\ÂŠ7KHÂŠGHIDXOWÂŠLVÂŠ
Internal (2x2).
Chapter 4: Wireless
For example, if a problematic link has traffic stability issues
and uses the Default, you may want to try the Alternative
to see if it improves the situation.
Note: The Data Rate Module affects the TX rate only,
not the RX rate. You can select Default or Alternative
on a single device; this option does not depend
on which algorithm is selected on the AP or its
stations.
â˘ PowerBeamM2 400 If you are not using a dish reflector,ÂŠ
then select Feed only - 3 dBi. Otherwise, keep theÂŠ
default, 400 - 18 dBi.
â˘ PowerBeamM5 300 If you are not using a dish reflector,ÂŠ
then select Feed only - 3 dBi. Otherwise, keep theÂŠ
default, 300 - 22 dBi.
â˘ PowerBeamM5 400 If you are not using a dish reflector,
then select Feed only - 3 dBi. Otherwise, keep the
default, 400 - 25 dBi.
â˘ PowerBeamM5 620 If you are not using a dish reflector,
then select Feed only - 3 dBi. Otherwise, keep the
default, 620 - 29 dBi.
â˘ PowerBridgeM3/M365 The default is 18 dBi.
â˘ PowerBridgeM5 The default is 24 dBi.
â˘ PowerBridgeM10 The default is 18 dBi.
Antenna Gain (Not available if the device uses an
integrated antenna.) Enter the antenna gain in dBi. With
Calculate EIRP Limit enabled, Antenna Gain calculates the
TX power backoff needed to remain in compliance with
local regulations. The Antenna Gain setting complements
the Cable Loss setting; they both affect the TX power of
the device.
Cable Loss (Only applicable to devices with external
antenna connectors.) Enter the cable loss in dB. With
Calculate EIRP Limit enabled, Cable Loss affects the TX
power of the device. In case you have high amounts of
cable loss, you may increase the TX power while remaining
in compliance with local regulations. The Cable Loss
setting complements the Antenna Gain setting; they both
affect the TX power of the device.
Output Power Defines the maximum average transmit
output power (in dBm) of the device. To specify the output
power, use the slider or manually enter the output power
value. The transmit power level maximum is limited
according to country regulations. (If the device has an
internal antenna, then Output Power is the output power
delivered to the internal antenna.)
Data Rate Module (Not applicable to the airGateway.)
You have a choice of data rate algorithms to use for your
link, Default or Alternative. If the Default is not working
well for your link, you can try the Alternative to determine
which is the best data rate algorithm for your individual
situation. The Alternative tries to move the link to a higher
data rate but continuously monitors the packet failure
counters. You should get more stable data rates when
using the Alternative; however, results will vary depending
on the linkâs specific environment and configuration.
Ubiquiti Networks, Inc.
Max TX Rate, Mbps Defines the maximum data rate
range (in Mbps) at which the device should transmit
wireless packets. You can fix a specific data rate between
0&6ÂŠÂŠDQGÂŠ0&6ÂŠ RUÂŠ0&6ÂŠÂŠIRUÂŠ[ÂŠFKDLQÂŠGHYLFHV ÂŠ:HÂŠ
recommend that you use the automatic option, especially
if you are having trouble getting connected or losing data
at a higher rate. In this case, the lower data rates will be
used automatically. If you select 20 MHz for the Channel
Width, the maximum data rate is MCS 7 - 65/72.2 0ESV ÂŠ
or MCS 15 - 130/144.4 0ESV ÂŠ,IÂŠ\RXÂŠVHOHFWÂŠ40 MHz for the
Channel Width, the maximum data rate is MCS 7 - 135/150
(Mbps) or MCS 15 - 270/300 (Mbps).
â˘ Automatic If enabled, the rate algorithm selects the
best data rate, depending on link quality conditions. We
recommend that you use this option, especially if you
are having trouble getting connected or losing data at a
higher rate. For more information about data rates, refer
to âAdvanced Wireless Settingsâ on page 45.
Note: The Max TX Rate is a range because it varies,
depending on which guard interval value is
automatically selected by the rate algorithm. If the
normal guard interval (800 ns) is used, then the
GDWDÂŠUDWHÂŠLVÂŠORZHUÂŠ,IÂŠWKHÂŠVKRUWÂŠJXDUGÂŠLQWHUYDOÂŠ QV ÂŠ
is used, then the data rate is higher.
Wireless Security
In Access Point or AP-Repeater mode, configure the wireless
security settings that will be used by the devices on your
wireless network.
In Station mode, enter the security settings of the AP that
the device is associated with.
The following table lists the wireless security methods
available for each wireless mode:
Security Method
none
Access Point
AP-Repeater
â
â
Station
â
â
WEP
WPA-AES
â
â
WPA2-AES
â
â
Âš If you select none as your security method, then this may compromise the
security of your network; however, you have the options of using RADIUS MAC
Authentication and MAC ACL.
Â˛ If you select WEP as your security method, then this may compromise the
security of your network; however, you have the option of using MAC ACL.
27
Chapter 4: Wireless
airOSÂŽ v5.6 User Guide
Security airOS supports the following wireless security
methods:
Acct Server IP/Port If the Accounting Server is enabled,
enter the IP address of the accounting server.
â˘ none If you want an open network without wireless
security, select none. You still have the option of using
RADIUS MAC authentication and MAC ACL.
In the second field, enter the UDP port of the RADIUS
accounting server. The most commonly used port is the
default, 1813, but this may vary depending on the RADIUS
server you are using.
â˘ WEP WEP (Wired Equivalent Privacy) is the oldest and
least secure security algorithm.
â˘ WPA-AES WPA (Wi-Fi Protected Access) security mode
with AES (Advanced Encryption Standard) support only.
AES is also known as CCMP (Counter Mode with Cipher
Block Chaining Message Authentication Code Protocol),
which uses the AES algorithm.
â˘ WPA2-AES WPA2 security mode with AES support only.
WPA2 was developed to strengthen wireless encryption
security and is stronger than WPA, so WPA2-AES is the
strongest security option available. If all of the wireless
devices on your network support this option, we
recommend that you select it.
Acct Server Secret If the Accounting Server is enabled,
enter the password. A shared secret is a case-sensitive text
string used to validate communication between an Access
Point and RADIUS server.
Show Check the box if you want to view the characters of
the Acct Server Secret.
Mac ACL This option enables the MAC address Access
Control List. For details, refer to âMAC ACLâ on page 30.
WEP
None
Authentication Type Select one of the following
authentication methods:
â˘ Open This option is selected by default. The station is
authenticated automatically by the AP.
â˘ Shared Key The station is authenticated after the
challenge, which is generated by the AP.
RADIUS MAC Authentication You can authenticate
devices using their MAC addresses.
MAC Format Select the appropriate format of the MAC
address.
Use Empty Password To submit the MAC address
without a password, check the Enable box.
Auth Server IP/Port In the first field, enter the IP
address of the RADIUS authentication server. RADIUS is a
QHWZRUNLQJÂŠSURWRFROÂŠSURYLGLQJÂŠFHQWUDOL]HGÂŠ$XWKHQWLFDWLRQÂŠ
$XWKRUL]DWLRQÂŠDQGÂŠ$FFRXQWLQJÂŠ $$$ ÂŠPDQDJHPHQWÂŠIRUÂŠ
computers to connect to and use a network service.
In the second field, enter the UDP port of the RADIUS
authentication server. The most commonly used port is
the default, 1812, but this may vary depending on the
RADIUS server you are using.
Auth Server Secret Enter the password. A shared
secret is a case-sensitive text string used to validate
communication between an Access Point and RADIUS
server.
Show Check the box if you want to view the characters of
the Auth Server Secret.
Accounting Server If you are using an accounting server,
check the Enable box.
28
WEP Key Length Specifies the length of the WEP security
key. Select one of the two options:
â˘ 64-bit This option is selected by default. A 64-bit key is
ÂŠ+(;ÂŠRUÂŠÂŠ$6&,,ÂŠFKDUDFWHUVÂŠLQÂŠOHQJWK
â˘ 128-bit The 128-bit option provides more security and
LVÂŠÂŠ+(;ÂŠRUÂŠÂŠ$6&,,ÂŠFKDUDFWHUVÂŠLQÂŠOHQJWK
Key Type Specifies the character format of the WEP key:
â˘ HEX By default, this option uses hexadecimal
characters. 0-9, A-F, or a-f are valid characters.
â˘ ASCII ASCII uses the standard English alphabet and
numeric characters.
WEP Key Enter the appropriate WEP encryption key:
Type
HEX
ASCII
64-bit
10 hexadecimal characters
(0-9, A-F or a-f )
Example: 00112233AA
5 ASCII characters
Example:
ubnt1
128-bit
26 hexadecimal characters
(0-9, A-F or a-f )
Example:
00112233445566778899AABBCC
13 ASCII characters
Example:
ubntproducts1
Key Index Specifies the index of the WEP key used. Four
different WEP keys can be configured at the same time,
but only one is used. To set the effective key, select 1, 2, 3,
or 4.
Ubiquiti Networks, Inc.
airOSÂŽ v5.6 User Guide
Chapter 4: Wireless
Mac ACL This option enables the MAC address Access
Control List. For details, refer to âMAC ACLâ on page 30.
WPA User Password Enter the password credential used
by the supplicant for EAP authentication.
WPA-AES or WPA2-AES
Show Check the box if you want to view the characters of
the WPA User Password.
The configuration options are the same. WPA2-AES is the
strongest security method. If all of the wireless devices on
your network support this option, we recommend that
you select it.
EAP- Access Point Mode
The options below apply in Access Point or AP-Repeater
mode only.
WPA Authentication Specify one of the following WPA
key selection methods:
â˘ PSK Pre-shared Key method (selected by default).
â˘ EAP EAP (Extensible Authentication Protocol)
IEEE 802.1x authentication method. This method is
commonly used in enterprise networks.
PSK
Auth Server IP/Port In the first field, enter the IP
address of the RADIUS authentication server. RADIUS is a
QHWZRUNLQJÂŠSURWRFROÂŠSURYLGLQJÂŠFHQWUDOL]HGÂŠ$XWKHQWLFDWLRQÂŠ
$XWKRUL]DWLRQÂŠDQGÂŠ$FFRXQWLQJÂŠ $$$ ÂŠPDQDJHPHQWÂŠIRUÂŠ
computers to connect to and use a network service.
In the second field, enter the UDP port of the RADIUS
authentication server. The most commonly used port is
1812, but this may vary depending on the RADIUS server
you are using.
WPA Preshared Key Specify a passphrase. The preshared
key is an alpha-numeric password between 8 and 63
characters long.
Show Check the box if you want to view the characters of
the WEP Preshared Key.
EAP
EAP - Station Mode
The options below apply in Station mode only.
Auth Server Secret Enter the password. A shared
secret is a case-sensitive text string used to validate
communication between an Access Point and RADIUS
server.
Show Check the box if you want to view the characters of
the Auth Server Secret.
Accounting Server If you are using an accounting server,
check the Enable box.
Acct Server IP/Port If the Accounting Server is enabled,
enter the IP address of the accounting server.
In the second field, enter the UDP port of the RADIUS
accounting server. The most commonly used port is 1813,
but this may vary depending on the RADIUS server you
are using.
Acct Server Secret If the Accounting Server is enabled,
enter the password. A shared secret is a case-sensitive text
string used to validate communication between an Access
Point and RADIUS server.
EAP-TTLS / EAP-PEAP Select the authentication protocol
used by your AP. The inner authentication protocol is set
to MSCHAPV2 by default.
WPA Anonymous Identity Enter the identification
credential used by the supplicant for EAP authentication
in unencrypted form.
Show Check the box if you want to view the characters of
the Acct Server Secret.
Mac ACL This option enables the MAC address Access
Control List. For details, refer to âMAC ACLâ on page 30.
WPA User Name Enter the identification credential used
by the supplicant for EAP authentication.
Ubiquiti Networks, Inc.
29
Chapter 4: Wireless
airOSÂŽ v5.6 User Guide
MAC ACL
The options below apply in Access Point or AP-Repeater
mode only.
MAC ACL The MAC address Access Control List (ACL) lets
you allow or deny clients connectivity to the device. When
enabled, you have the following options:
Policy Select one of the policy types:
â˘ Allow Wireless clients on the list can access the device.
Any wireless client that is not on the list is denied access
to the device.
â˘ Deny Wireless clients on the list are denied access to
the device. Any wireless client that is not on the list can
access the device.
â˘ ACL To add MAC addresses of wireless clients, click ACL.
- Enabled The policy is applied to this wireless client.
- MAC Enter the MAC address in this format:
XX:XX:XX:XX:XX:XX (each X represents a valid
hexadecimal character: 0-9, A-F, or a-f ).
- Comment Enter a description of the wireless client.
- Action Click Add to add the MAC address of a
wireless client. Click Del to remove the MAC address
of a wireless client. Click Edit to make changes to an
entry.
Note: MAC ACL should be used in combination
with a security method such as WPA or WPA2.
It should not be used as the only method of
security on your network.
30
Ubiquiti Networks, Inc.
airOSÂŽ v5.6 User Guide
Chapter 5: Network
The Network page allows you to configure bridge or
routing functionality and IP settings.
Chapter 5: Network
â˘ Bridge The device acts as a transparent bridge, operates
in Layer 2 (like a managed switch), and usually has only
one IP address (for management purposes only).
Change To save or test your changes, click Change.
A new message appears. You have three options:
â˘ Apply To immediately save your changes, click Apply.
â˘ Test To try the changes without saving them, click
Test. To keep the changes, click Apply. If you do not
click Apply within 180 seconds (the countdown is
displayed), the device times out and resumes its earlier
configuration.
â˘ Discard To cancel your changes, click Discard.
â˘ Router The device is usually separated into two
networks or subnets (one WAN and one LAN). The
WLAN functions as the Wide Area Network (WAN). The
Ethernet ports function as the LAN. Each wireless or
wired interface on the WAN or LAN has an IP address (for
management purposes only).
Network Role
airOS supports Bridge, Router, and SOHO Router modes.
Only the routers can support the router modes.
Network Mode Specify the Network Mode of the device.
The default setting is device-specific. The mode depends
on the network topology requirements.
Bridge mode is adequate if you have a very small network.
However, a larger network has significantly more traffic
that requires management by a device using Router or
SOHO Router mode. Router or SOHO Router mode keeps
broadcast traffic within its respective broadcast domain,
so that broadcast traffic will not overload the overall traffic
in the network.
Ubiquiti Networks, Inc.
â˘ SOHO Router SOHO (Small Office/Home Office) Router
mode is derived from Router mode. The main Ethernet
port labeled <ÂˇÂˇÂˇ> functions as the WAN port. The WLAN
and other Ethernet ports function as the LAN. Each
wireless or wired interface on the WAN or LAN has an IP
address (for management purposes only).
31
Chapter 5: Network
airOSÂŽ v5.6 User Guide
The following summarizes the differences between Bridge,
Router, and SOHO Router modes:
Bridge Mode
â˘ The device forwards all network management and
data packets from one network interface to the other
without any intelligent routing. For simple applications,
this provides an efficient and fully transparent network
solution.
â˘ There is no network segmentation, and the broadcast
domain is the same. Bridge mode does not block
any broadcast or multicast traffic. You can configure
additional firewall settings for Layer 2 packet filtering
and access control.
â˘ WLAN and LAN interfaces belong to the same network
segment and share the same IP address space. They
form the virtual bridge interface while acting as bridge
ports. The device features IP settings for management
purposes.
Router Mode
â˘ The device operates in Layer 3 to perform routing and
enable network segmentation â wireless clients and
the WAN interface are on a different IP subnet. Router
mode blocks broadcasts and can pass through multicast
packet traffic. You can configure additional firewall
settings for Layer 3 packet filtering and access control.
â˘ The device can act as a DHCP server and use Network
Address Translation (Masquerading), which is widely
used by APs. NAT acts as the firewall between the LAN
DQG:$1
â˘ For example, Router mode is used in a typical Customer
Premises Equipment (CPE) installation. The device acts
as the demarcation (demarc) point between the CPE
and Wireless Internet Service Provider (WISP), with the
wireless interface of the device connecting to the WISP.
SOHO Router Mode
â˘ The device operates in Layer 3 to perform routing and
enable network segmentation â wireless clients and the
WAN interface are on a different IP subnet. SOHO Router
mode blocks broadcasts and can pass through multicast
packet traffic. You can configure additional firewall
settings for Layer 3 packet filtering and access control.
â˘ The device can act as a DHCP server and use Network
Address Translation (Masquerading), which is widely
used by APs. NAT acts as the firewall between the LAN
DQG:$1
â˘ For example, SOHO Router mode is used in an
installation where the main Ethernet port connects to
the Internet Service Provider (ISP) via a modem.
â˘ In devices with one Ethernet port (while operating in
Access Point or AP-Repeater mode), SOHO Router mode
works like Router mode, except that the LAN port
works as a WAN port, and the WLAN works as the local
network. In devices with two or more Ethernet ports,
the main Ethernet port becomes the WAN port, and the
WLAN and other LAN ports become the local network.
Note: Do not use the SOHO Router mode in
combination with Station wireless mode; this may
cause the device to become inaccessible. If this
did happen, reset the device to defaults; press and
hold the Reset button for eight seconds and then
release it.
Disable Network Disables the WLAN, LAN0, or LAN1
interface(s). Use this setting with caution as you cannot
establish any Layer 2 or Layer 3 connection through the
disabled interface. You cannot access the device from
the wireless or wired network that is connected to the
disabled interface.
The following diagram shows the NanoBeam at a
residence wirelessly connecting to a WISP tower.
Configuration Mode
WISP Tower
The Network page has two views, Simple and Advanced.
NanoBeam
Configuration Mode Select the appropriate mode for
your application:
â˘ Simple The following basic configuration settings are
available:
â˘ âNetwork Roleâ on page 31
â˘ âConfiguration Modeâ on page 32
The following settings are available in Bridge mode only:
â˘ âManagement Network Settings â Bridge Modeâ on
page 33
32
Ubiquiti Networks, Inc.
airOSÂŽ v5.6 User Guide
Chapter 5: Network
The following settings are available in Router or SOHO
Router mode only:
- DHCP Fallback IP Specify the IP address for the
device to use if a DHCP server is not found.
â˘ âWAN Network Settingsâ on page 34
- DHCP Fallback Netmask Specify the netmask for the
device to use if a DHCP server is not found.
â˘ âLAN Network Settingsâ on page 38
â˘ âPort Forwardingâ on page 40
â˘ âMulticast Routing Settingsâ on page 40
The following settings are available in SOHO Router
PRGHRQO\
â˘ Static Assign static IP settings to the device.
Note: IP settings should be consistent with the
address space of the deviceâs network segment.
â˘ âDHCP Address Reservationâ on page 40
â˘ Advanced Displays the advanced configuration
settings, in addition to the basic configuration settings:
â˘ âInterfacesâ on page 41
â˘ âIP Aliasesâ on page 41
â˘ âVLAN Networkâ on page 41
â˘ âBridge Networkâ on page 42
â˘ âFirewallâ on page 42
â˘ âIPv6 Firewallâ on page 43
â˘ âStatic Routesâ on page 43
â˘ âTraffic Shapingâ on page 44
The following settings are available in Router or SOHO
Router mode only:
â˘ âManagement Network Settings â Router or SOHO
Modeâ on page 34
â˘ âIPv6 Static Routesâ on page 44
Management Network Settings â
Bridge Mode
- IP Address Specify the IP address of the device. This
IP will be used for device management purposes.
- Netmask Enter the netmask of the device. The
netmask defines the address space of the deviceâs
network segment. The netmask 255.255.255.0 is
typically used for Class C networks.
- Gateway IP Typically, this is the IP address of the host
router, which provides the point of connection to the
Internet. This can be a DSL modem, cable modem, or
WISP gateway router. The device directs data packets
to the gateway if the destination host is not within the
local network.
Note: In Bridge mode, the gateway IP address
should be from the same address space (on the
same network segment) as the device.
Management Interface (Available in Advanced view.)
Select the interface used for management.
Management IP Address The device can use a static IP
address or obtain an IP address from its DHCP server.
â˘ DHCP The local DHCP server assigns a dynamic IP
address, gateway IP address, and DNS address to the
device.
Ubiquiti Networks, Inc.
- Primary DNS IP Specify the IP address of the primary
DNS (Domain Name System) server for management
purposes only.
- Secondary DNS Specify the IP address of the
secondary DNS server for management purposes only.
This entry is optional and used only if the primary DNS
server is not responding.
MTU (Available in Simple view.) The Maximum
Transmission Unit (MTU) is the maximum frame size (in
bytes) that a network interface can transmit or receive. The
default is 1500.
33
Chapter 5: Network
Management VLAN (Available in Simple view.) If enabled,
automatically creates a management Virtual Local Area
Network (VLAN).
airOSÂŽ v5.6 User Guide
â˘ SLAAC If IPv6 is enabled, then SLAAC (StateLess Address
Auto-Configuration) is enabled by default; the device
assign itself an IPv6 address.
â˘ VLAN ID Enter a unique VLAN ID from 2 to 4094.
Note: If Management VLAN is enabled, then the
device will not be accessible from other VLANs,
including the untagged VLAN.
Auto IP Aliasing If enabled, automatically generates an
IP address for the corresponding WLAN/LAN interface.
The generated IP address is a unique Class B IP address
from the 169.254.X.Y range (netmask 255.255.0.0), which
is intended for use within the same network segment only.
The Auto IP always starts with 169.254.X.Y, with X and Y
as the last two octets from the MAC address of the device.
For example, if the MAC is 00:15:6D:A3:04:FB, then the
generated unique Auto IP will be 169.254.4.251.
The Auto IP Aliasing setting can be useful because you
can still access and manage devices even if you lose,
misconfigure, or forget their IP addresses. Because an
Auto IP address is based on the last two octets of the MAC
address, you can determine the IP address of a device if
you know its MAC address.
Management Network Settings â
Router or SOHO Mode
Management Interface (Available in Advanced view.)
Select the interface used for management.
WAN Network Settings
(Available in Router or SOHO Router mode only)
STP Multiple interconnected bridges create larger
networks. Spanning Tree Protocol (STP) eliminates loops
from the topology while finding the shortest path within a
network.
If enabled, the device bridge communicates with other
network devices by sending and receiving Bridge Protocol
Data Units (BPDU). STP should be disabled (default setting)
when the device is the only bridge on the LAN or when
there are no loops in the topology, as there is no need for
the bridge to use STP in this case.
IPv6 Disabled by default. Select IPv6 if you want to use
IPv6 addressing.
WAN Interface Select the interface used for connection
to the external network (Internet).
WAN IP Address The IP address of the WAN interface
connected to the external network. You can use this IP
address for routing and device management purposes.
The device can use one of the following:
â˘ âDHCPâ on page 34
â˘ âStaticâ on page 35
â˘ âPPPoEâ on page 36
â˘ Static Select Static to manually define the IPv6 settings
of the device. Complete the following:
- IPv6 Address Enter the IPv6 address of the device.
DHCP
The external DHCP server assigns a dynamic IP address,
gateway IP address, and DNS address to the device.
- IPv6 Netmask Enter the IPv6 netmask of the device.
The default is 64.
34
Ubiquiti Networks, Inc.
airOSÂŽ v5.6 User Guide
Chapter 5: Network
DHCP Fallback IP Specify the IP address for the device to
use if an external DHCP server is not found.
DHCP Fallback Netmask Specify the netmask for the
device to use if an external DHCP server is not found.
MTU (Available in Simple view.) The Maximum
Transmission Unit (MTU) is the maximum frame size (in
bytes) that a network interface can transmit or receive. The
default is 1500.
NAT Network Address Translation (NAT) is an IP
masquerading technique that hides private network IP
address space (on LAN interface) behind a single public IP
address (on WAN interface).
NAT is implemented using the masquerade type firewall
rules. NAT firewall entries are stored in the iptables
nat table. Specify static routes to allow packets to pass
through the airOS device if NAT is disabled.
â˘ NAT Protocol Devices on the LAN side behind a NATâed
router have no transparent connectivity with devices
on WAN side; this may be critical for some Internet
protocols. For this purpose NAT Protocol has NAT helpers
that enable NAT traversal for various protocols: SIP, PPTP,
FTP, and RTSP.
If NAT is enabled, you can modify data packets to allow
them to pass through the device. To avoid modification
of some specific types of packets, such as SIP, PPTP, FTP,
or RTSP, then uncheck the respective box(es).
Block management access To block device management
from the WAN interface, check this box. This feature makes
Router or SOHO Router mode more secure if the device has
a public IP address.
â˘ DMZ IP Specify the IP address of the local host network
device. The DMZ host device will be completely exposed
to the external network.
Auto IP Aliasing If enabled, automatically generates an
IP address for the corresponding WLAN/LAN interface.
The generated IP address is a unique Class B IP address
from the 169.254.X.Y range (netmask 255.255.0.0), which
is intended for use within the same network segment only.
The Auto IP always starts with 169.254.X.Y, with X and Y
as the last two octets from the MAC address of the device.
For example, if the MAC is 00:15:6D:A3:04:FB, then the
generated unique Auto IP will be 169.254.4.251.
The Auto IP Aliasing setting can be useful because you
can still access and manage devices even if you lose,
misconfigure, or forget their IP addresses. Because an
Auto IP address is based on the last two octets of the MAC
address, you can determine the IP address of a device if
you know its MAC address.
MAC Address Cloning When enabled, you can change
the MAC address of the respective interface. This is
especially useful if your ISP only assigns one valid IP
address and it is associated to a specific MAC address. This
is usually used by cable operators or some WISPs.
â˘ MAC Address Enter the MAC address you want to clone
to the respective interface. This becomes the new MAC
address of the interface.
Static
Assign static IP settings to the device.
Note: IP settings should be consistent with the
address space of the deviceâs network segment.
DMZ DMZ (Demilitarized Zone) specifically allows one
computer/device behind NAT to become âdemilitarizedâ,
so all ports from the public network are forwarded to the
ports of this private network, similar to a 1:1 NAT.
â˘ DMZ Management Ports The airOS device responds to
requests from the external network as if it were the host
device that is specified with the DMZ IP address. DMZ
Management Ports is disabled by default; the device is
accessible from the WAN port. If DMZ Management Ports
is enabled, all management ports will be forwarded to
the device, so youâll only be able to access the device
from the LAN side.
The default values of the management ports are:
Management Method
Management Port
HTTP/HTTPS
80/443 TCP
SSH
22 TCP
Telnet
23 TCP
SNMP
161 UDP
Discovery
10001 UDP
airView
18888 TCP
Ubiquiti Networks, Inc.
IP Address Specify the IP address of the device. This IP
will be used for device management purposes.
Netmask Enter the netmask of the device. The netmask
defines the address space of the deviceâs network
segment. The netmask 255.255.255.0 is typically used for
Class C networks.
35
Chapter 5: Network
Gateway IP Typically, this is the IP address of the host
router, which provides the point of connection to the
Internet. This can be a DSL modem, cable modem, or
WISP gateway router. The device directs data packets to
the gateway if the destination host is not within the local
network.
airOSÂŽ v5.6 User Guide
The default values of the management ports are:
Primary DNS IP Specify the IP address of the primary
DNS (Domain Name System) server for management
SXUSRVHVRQO\
Secondary DNS IP Specify the IP address of the
secondary DNS server for management purposes only.
This entry is optional and used only if the primary DNS
server is not responding.
MTU (Available in Simple view.) The Maximum
Transmission Unit (MTU) is the maximum frame size (in
bytes) that a network interface can transmit or receive. The
default is 1500.
NAT Network Address Translation (NAT) is an IP
masquerading technique that hides private network IP
address space (on LAN interface) behind a single public IP
address (on WAN interface).
NAT is implemented using the masquerade type firewall
rules. NAT firewall entries are stored in the iptables
nat table. Specify static routes to allow packets to pass
through the airOS device if NAT is disabled.
â˘ NAT Protocol Devices on the LAN side behind a NATâed
router have no transparent connectivity with devices
on WAN side; this may be critical for some Internet
protocols. For this purpose NAT Protocol has NAT helpers
that enable NAT traversal for various protocols: SIP, PPTP,
FTP, and RTSP.
If NAT is enabled, you can modify data packets to allow
them to pass through the device. To avoid modification
of some specific types of packets, such as SIP, PPTP, FTP,
or RTSP, then uncheck the respective box(es).
Block management access To block device management
from the WAN interface, check this box. This feature makes
Router mode more secure if the device has a public IP
address.
Management Method
Management Port
HTTP/HTTPS
80/443 TCP
SSH
22 TCP
Telnet
23 TCP
SNMP
161 UDP
Discovery
10001 UDP
airView
18888 TCP
â˘ DMZ IP Specify the IP address of the local host network
device. The DMZ host device will be completely exposed
to the external network.
Auto IP Aliasing If enabled, automatically generates an
IP address for the corresponding WLAN/LAN interface.
The generated IP address is a unique Class B IP address
from the 169.254.X.Y range (netmask 255.255.0.0), which
is intended for use within the same network segment only.
The Auto IP always starts with 169.254.X.Y, with X and Y
as the last two octets from the MAC address of the device.
For example, if the MAC is 00:15:6D:A3:04:FB, then the
generated unique Auto IP will be 169.254.4.251.
The Auto IP Aliasing setting can be useful because you
can still access and manage devices even if you lose,
misconfigure, or forget their IP addresses. Because an
Auto IP address is based on the last two octets of the MAC
address, you can determine the IP address of a device if
you know its MAC address.
MAC Address Cloning When enabled, you can change
the MAC address of the respective interface. This is
especially useful if your ISP only assigns one valid IP
address and it is associated to a specific MAC address. This
is usually used by cable operators or some WISPs.
â˘ MAC Address Enter the MAC address you want to clone
to the respective interface. This becomes the new MAC
address of the interface.
PPPoE
DMZ DMZ (Demilitarized Zone) specifically allows one
computer/device behind NAT to become âdemilitarizedâ,
so all ports from the public network are forwarded to the
ports of this private network, similar to a 1:1 NAT.
Point-to-Point Protocol over Ethernet (PPPoE) is a virtual
private and secure connection between two systems
that enables encapsulated data transport. Subscribers
sometimes use PPPoE to connect to Internet Service
Providers (ISPs), typically DSL providers.
â˘ DMZ Management Ports The airOS device responds to
requests from the external network as if it were the host
device that is specified with the DMZ IP address. DMZ
Management Ports is disabled by default; the device is
accessible from the WAN port. If DMZ Management Ports
is enabled, all management ports will be forwarded to
the device, so youâll only be able to access the device
from the LAN side.
Select PPPoE to configure a PPPoE tunnel. You can
configure only the WAN interface as a PPPoE client
because all the traffic will be sent via this tunnel. After the
PPPoE connection is established, the device will obtain the
IP address, default gateway IP, and DNS server IP address
from the PPPoE server. The broadcast address is used to
discover the PPPoE server and establish the tunnel.
36
If there is a PPPoE connection established, then the IP
address of the PPP interface will be displayed on the
Main page next to the PPP interface statistics; otherwise
a Not Connected message and Reconnect button will be
displayed. To re-connect a PPPoE tunnel, click Reconnect.
Ubiquiti Networks, Inc.
airOSÂŽ v5.6 User Guide
Chapter 5: Network
Block management access To block device management
from the WAN interface, check this box. This feature makes
Router mode more secure if the device has a public IP
address.
DMZ DMZ (Demilitarized Zone) specifically allows one
computer/device behind NAT to become âdemilitarizedâ,
so all ports from the public network are forwarded to the
ports of this private network, similar to a 1:1 NAT.
â˘ DMZ Management Ports The airOS device responds to
requests from the external network as if it were the host
device that is specified with the DMZ IP address. DMZ
Management Ports is disabled by default; the device is
accessible from the WAN port. If DMZ Management Ports
is enabled, all management ports will be forwarded to
the device, so youâll only be able to access the device
from the LAN side.
The default values of the management ports are:
Username Specify the username to connect to the PPPoE
server; this must match the username configured on the
PPPoE server.
Password Specify the password to connect to the PPPoE
server; this must match the password configured on the
PPPoE server.
Show Check the box if you want to view the characters of
the password.
Management Method
Management Port
HTTP/HTTPS
80/443 TCP
SSH
22 TCP
Telnet
23 TCP
SNMP
161 UDP
Discovery
10001 UDP
airView
18888 TCP
Service Name Specify the name of the PPPoE service.
Fallback IP Specify the IP address for the device to use if
the PPPoE server does not assign an IP address.
Fallback Netmask Specify the netmask for the device to
use if the PPPoE server does not assign a netmask.
MTU/MRU The size (in bytes) of the Maximum
Transmission Unit (MTU) and Maximum Receive Unit
(MRU) used for data encapsulation during transfer through
the PPP tunnel. The default value is 1492.
Encryption Enables the use of Microsoft Point-to-Point
Encryption (MPPE).
NAT Network Address Translation (NAT) is an IP
masquerading technique that hides private network IP
address space (on LAN interface) behind a single public IP
address (on WAN interface).
NAT is implemented using the masquerade type firewall
rules. NAT firewall entries are stored in the iptables
nat table. Specify static routes to allow packets to pass
through the airOS device if NAT is disabled.
â˘ NAT Protocol Devices on the LAN side behind a NATâed
router have no transparent connectivity with devices
on WAN side; this may be critical for some Internet
protocols. For this purpose NAT Protocol has NAT helpers
that enable NAT traversal for various protocols: SIP, PPTP,
FTP, and RTSP.
If NAT is enabled, you can modify data packets to allow
them to pass through the device. To avoid modification
of some specific types of packets, such as SIP, PPTP, FTP,
or RTSP, then uncheck the respective box(es).
Ubiquiti Networks, Inc.
â˘ DMZ IP Specify the IP address of the local host network
device. The DMZ host device will be completely exposed
to the external network.
Auto IP Aliasing If enabled, automatically generates an
IP address for the corresponding WLAN/LAN interface.
The generated IP address is a unique Class B IP address
from the 169.254.X.Y range (netmask 255.255.0.0), which
is intended for use within the same network segment only.
The Auto IP always starts with 169.254.X.Y, with X and Y
as the last two octets from the MAC address of the device.
For example, if the MAC is 00:15:6D:A3:04:FB, then the
generated unique Auto IP will be 169.254.4.251.
The Auto IP Aliasing setting can be useful because you
can still access and manage devices even if you lose,
misconfigure, or forget their IP addresses. Because an
Auto IP address is based on the last two octets of the MAC
address, you can determine the IP address of a device if
you know its MAC address.
MAC Address Cloning When enabled, you can change
the MAC address of the respective interface. This is
especially useful if your ISP only assigns one valid IP
address and it is associated to a specific MAC address. This
is usually used by cable operators or some WISPs.
â˘ MAC Address Enter the MAC address you want to clone
to the respective interface. This becomes the new MAC
address of the interface.
37
Chapter 5: Network
IPv6 Disabled by default. Select IPv6 if you want to use
IPv6 addressing.
â˘ Static (Not available for PPPoE) Select Static to
manually define the IPv6 settings of the device.
Complete the following:
- IPv6 Address Enter the IPv6 address of the device.
- IPv6 Netmask Enter the IPv6 netmask of the device.
The default is 64.
- IPv6 Gateway Enter the IPv6 address of the local
gateway, which is typically the host router.
airOSÂŽ v5.6 User Guide
Netmask Enter the netmask of the device. The netmask
defines the address space of the deviceâs network
segment. The netmask 255.255.255.0 is typically used for
Class C networks.
MTU (Available in Simple view.) The Maximum
Transmission Unit (MTU) is the maximum frame size (in
bytes) that a network interface can transmit or receive. The
default is 1500.
DHCP Server The built-in DHCP server assigns IP
addresses to clients connected to the LAN interface.
â˘ Disabled The device does not assign local IP addresses.
â˘ SLAAC Select SLAAC (StateLess Address
Auto-Configuration) to have the device assign itself an
IPv6 address.
â˘ Enabled The device assigns IP addresses to client
devices on the local network.
â˘ DHCPv6 Select DHCPv6 to have an external DHCP
server assign a dynamic IP address, gateway IP address,
and DNS address to the device.
LAN Network Settings
(Available in Router or SOHO Router mode only)
- Range Start and End Determines the range of IP
addresses assigned by the DHCP server.
LAN Interface In Simple view the LAN interface is
displayed. Select the interface used for LAN connection.
Click Del to delete the interface. If there is no interface
selected, select an interface from the Add LAN drop-down
OLVWÂŠDQGÂŠFOLFNAdd.
IP Address The IP address of the LAN interface. If the LAN
interface is the Bridge, all the bridge ports (for example,
the Ethernet and WLAN interfaces) will be considered as
local network interfaces. This IP will be used for routing
of the local network; it will be the gateway IP for all the
devices on the local network. This IP address can be used
for management of the device.
38
- Netmask Enter the netmask of the device. The
netmask defines the address space of the deviceâs
network segment. The netmask 255.255.255.0 is
typically used for Class C networks.
- Lease Time The IP addresses assigned by the DHCP
server are valid only for the duration specified by
the lease time. Increasing the time ensures client
operation without interruption, but could introduce
potential conflicts. Decreasing the lease time avoids
potential address conflicts, but might cause more
slight interruptions to the client while it acquires a
new IP address from the DHCP server. The time is
expressed in seconds.
Ubiquiti Networks, Inc.
airOSÂŽ v5.6 User Guide
- DNS Proxy The Domain Name System (DNS) proxy
server forwards the DNS requests from the hosts on
the local network to the DNS server. If enabled, the
device (LAN port) will act as the DNS proxy server
and forward DNS requests from the hosts on the local
network to the real DNS server.
- Primary DNS If DNS Proxy is disabled, then specify
the IP address of the primary DNS server for DHCP
clients.
Chapter 5: Network
- Stateless The DHCP clients select their own IPv6
addresses (also known as SLAAC). (The DHCPv6 server
assigns network settings except for the IP addresses to
DHCP clients.) A /64 mask on the LAN is required.
â˘ DNS Proxy If Stateless or Stateful is selected, then
DNS Proxy is enabled by default. The Domain
Name System (DNS) proxy server forwards the DNS
requests from the hosts on the local network to the
DNS server.
- Secondary DNS If DNS Proxy is disabled, then specify
the IP address of the secondary DNS server. This entry
is optional and used only if the primary DNS server is
not responding.
â˘ Relay Relays DHCP messages between DHCP clients
and DHCP servers on different IP networks.
â˘ Preferred DNS If DNS Proxy is disabled, then specify
the IP address of the preferred DNS server.
- Stateful The DHCPv6 server assigns IPv6 addresses
and other network settings to DHCP clients.
â˘ DNS Proxy If Stateless or Stateful is selected, then
DNS Proxy is enabled by default. The Domain
Name System (DNS) proxy server forwards the DNS
requests from the hosts on the local network to the
DNS server.
- DHCP Server IP Specify the IP address of the DHCP
server that should get the DHCP messages.
- Agent-ID Specify the identifier of the DHCP relay
agent.
â˘ Preferred DNS If DNS Proxy is disabled, then specify
the IP address of the preferred DNS server.
UPnP Allows the use of Universal Plug-and-Play (UPnP)
network protocol for gaming, videos, chat, conferencing,
and other applications.
Add LAN (Available in Advanced view.) Select an interface,
and then click Add.
IPv6 Disabled by default. Select IPv6 if you want to use
IPv6 addressing.
â˘ IPv6 Address (Available if DHCPv6 is enabled for IPv6
in the WAN Network Settings.) Select the appropriate
addressing method, Static or Prefix Delegation:
- Static Select Static to manually define the IPv6
settings of the device. Complete the following:
â˘ IPv6 Address Enter the IPv6 address of the device.
â˘ IPv6 DHCP Server The built-in DHCPv6 server
assigns IPv6 addresses to clients connected to the
wireless interface and LAN interface while the device is
operating in Access Point or AP-Repeater wireless mode.
The built-in DHCP server assigns IPv6 addresses to
clients connected to the LAN interface while the device
is operating in Station mode.
â˘ IPv6 Netmask Enter the IPv6 netmask of the
device. The default is 64.
â˘ IPv6 DHCP Server Refer to the IPv6 DHCP Server
description in the previous column.
- Disabled The device does not assign local IPv6
addresses and other network settings.
Ubiquiti Networks, Inc.
39
Chapter 5: Network
- Prefix Delegation Select this option to delegate a
pool of IPv6 addresses. Then configure the following:
â˘ IPv6 Prefix Length Enter the delegated prefix
length provided by the DHCPv6 server and typically
specified by the WISP. The default is 64.
â˘ IPv6 DHCP Server Refer to âIPv6 DHCP Serverâ on
page 39.
airOSÂŽ v5.6 User Guide
Enabled Enables the specific port forwarding rule. All
the added port forwarding rules are saved in the system
configuration file; however, only the enabled port
forwarding rules are active on the device.
Interface Select the appropriate interface.
Private IP The IP address of the local host that needs to
be accessible from the external network.
Private Port The TCP or UDP port of the application
running on the local host. The specified port will be
accessible from the external network.
Type The Layer 3 protocol (IP) type that needs to be
forwarded from the local network.
DHCP Address Reservation
(Available in SOHO Router or Router mode with the DHCP
server enabled)
The DHCP server assigns dynamic IP addresses to its
DHCP clients; however, you can map a static IP address
to a specific DHCP client using its unique MAC address.
Click the + button to display the DHCP Address Reservation
section.
Source IP/mask The IP address and netmask of the
source device.
Public IP/mask The public IP address and netmask of the
device that will accept and forward the connections from
the external network to the local host.
Public Port The TCP or UDP port of the device that will
accept and forward the connections from the external
network to the local host.
Comment Enter a brief description of the port
forwarding functionality, such as FTP server, web server, or
game server.
Action You have the following options:
Enabled Enables the specific DHCP address reservation.
â˘ Add Add a port forwarding rule.
Interface Select the appropriate interface.
â˘ Edit Make changes to a port forwarding rule. Click Save
to save your changes.
MAC Address Enter the MAC address of the DHCP client.
IP Address Enter the IP address that should be assigned.
â˘ Del Delete a port forwarding rule.
Comment You can enter a brief description of the
purpose for the DHCP address reservation.
Multicast Routing Settings
Action You have the following options:
With a multicast design, applications can send one copy
of each packet and address it to a group of computers
that want to receive it. This technique addresses packets
to a group of receivers rather than to a single receiver. It
relies on the network to forward the packets to the hosts
that need to receive them. Common routers isolate all the
broadcast (thus multicast) traffic between the local and
external networks; however, the device provides multicast
traffic pass-through functionality.
â˘ Add Add a DHCP address reservation.
â˘ Edit Make changes to a DHCP address reservation. Click
Save to save your changes.
â˘ Del Delete a DHCP address reservation.
Port Forwarding
(Available in Router or SOHO Router mode only)
Port forwarding allows specific ports of the hosts on the
local network to be forwarded to the external network
(WAN). This is useful for a number of applications (such
as FTP servers, VoIP, gaming) that require different host
systems to be seen using a single common IP address/
port. Click the + button to display the Port Forwarding
section.
40
(Available in Router or SOHO Router mode only)
Ubiquiti Networks, Inc.
airOSÂŽ v5.6 User Guide
Chapter 5: Network
Interface Select the appropriate interface.
Multicast Routing Enables multicast packet pass-through
between local and external networks while the device is
operating in Router mode. Multicast intercommunication
is based on Internet Group Management Protocol (IGMP).
IP Address The alternative IP address for the interface.
This can be used for routing or device management
purposes.
Multicast Upstream Specify the source of multicast
traffic.
Netmask The network address space identifier for the IP
alias.
Multicast Downstream Specify the destination(s) of
multicast traffic.
Comment You can enter a brief description of the
purpose for the IP alias.
Add Add a destination.
Action You have the following options:
Del Delete a destination.
â˘ Add Adds a IP alias.
Interfaces
â˘ Edit Make changes to an IP alias. Click Save to save your
changes.
(Available in Advanced view.) The Maximum Transmission
Unit (MTU) is the maximum frame size (in bytes) that
a network interface can transmit or receive. You can
configure a different MTU value for each of the interfaces.
Click the + button to display the Interfaces section.
â˘ Del Delete an IP alias.
VLAN Network
(Available in Advanced view.) You can create multiple
Virtual Local Area Networks (VLANs). Click the + button to
display the VLAN Network section.
Enabled Enables the specific VLAN. All the added VLANs
are saved in the system configuration file; however, only
the enabled VLANs are active on the device.
Interface Displays the name of the interface.
Interface Select the appropriate interface.
MTU Limited by the hardware capabilities of the specific
product, the maximum MTU value is typically 2024. The
default is 1500.
VLAN ID The VLAN ID is a unique value assigned to
each VLAN at a single device; every VLAN ID represents a
different VLAN. The VLAN ID range is 2 to 4094.
Action Click Edit to change the MTU. Then click Save to
apply your change.
Comment You can enter a brief description of the
purpose for the VLAN.
IP Aliases
Action You have the following options:
(Available in Advanced view.) You can configure IP aliases
for the network interfaces for management purposes. For
example, you may need multiple IP addresses (one private
IP address and one public IP address) for a single device. If
a CPE uses PPPoE, the CPE obtains a public PPPoE address,
but the network administrator assigns an internal IP alias
to the device. This way the network administrator can
manage the device internally without going through the
PPPoE server.
â˘ Add Add a VLAN.
â˘ Edit Make changes to a VLAN. Click Save to save your
changes.
â˘ Del Delete a VLAN.
Note: A VLAN cannot be deleted if it is selected as
the management interface.
Click the + button to display the IP Aliases section.
Enabled Enables the specific IP alias. All the added IP
aliases are saved in the system configuration file; however,
only the enabled IP aliases are active on the device.
Ubiquiti Networks, Inc.
41
Chapter 5: Network
airOSÂŽ v5.6 User Guide
Bridge Network
Firewall
(Available in Advanced view.) You can create one or
more bridge networks if you need complete Layer 2
transparency. This is similar to using a switch â all traffic
flows through a bridge, in one port and out another
port, regardless of VLANs or IP addresses. For example,
if you want to use the same IP subnet on both sides of a
device, then you create a bridge network. There are many
different scenarios that could require bridged interfaces,
so the Bridge Network section is designed to allow
flexibility.
(Available in Advanced view.) You can configure firewall
rules for the network interfaces. Click the + button to
display the Firewall section.
Click the + button to display the Bridge Network section.
Enabled Enables the specific firewall rule. All the added
firewall rules are saved in the system configuration file;
however, only the enabled firewall rules are active on the
device.
Enable Enables firewall functionality.
Target To allow packets to pass through the firewall
unmodified, select ACCEPT. To block packets, select
DROP.
Enabled Enables the specific bridge network. All
the added bridge networks are saved in the system
configuration file; however, only the enabled bridge
networks are active on the device.
Interface The interface is automatically displayed.
STP Multiple interconnected bridges create larger
networks using IEEE 802.1d Spanning Tree Protocol
(STP), which is used for finding the shortest path within a
network and eliminating loops from the topology.
If enabled, the device bridge communicates with other
network devices by sending and receiving Bridge Protocol
Data Units (BPDU). STP should be disabled (default setting)
when the device is the only bridge on the LAN or when
there are no loops in the topology, as there is no need for
the bridge to use STP in this case.
Ports Select the appropriate ports for your bridge
network. (Virtual ports are available if you have created
VLANs.)
â˘ Add Select a port.
â˘ Del Delete a port.
Comment You can enter a brief description of the
purpose for the bridge network.
Action You have the following options:
â˘ Add Add a bridge network.
â˘ Del Delete a bridge network.
Note: A bridge network cannot be deleted if it is
selected as the management interface.
Interface Select the appropriate interface where the
firewall rule is applied. To apply the firewall rule to all
interfaces, select ANY.
IP Type Sets which specific Layer 3 protocol type (IP, ICMP,
TCP, UDP, P2P) should be filtered.
! Can be used to invert the Source IP/Mask, Source Port,
Destination IP/Mask, and/or Destination Port filtering
criteria. For example, if you enable ! (Not) for the specified
Destination Port value 443, then the filtering criteria will
be applied to all the packets sent to any Destination Port
except port 443, which is commonly used by HTTPS.
Source IP/Mask Specify the source IP of the packet
(specified within the packet header). Usually it is the
IP of the host system that sends the packets. The mask
is in CIDR or slash notation. For example, if you enter
192.168.1.0/24, you are entering the range of 192.168.1.0
to 192.168.1.255.
Source Port Check the box and specify the source port of
the packet (specified within the packet header). Usually it
is the port of the host system application that sends the
packets.
Destination IP/Mask Specify the destination IP of the
packet (specified within the packet header). Usually it is
the IP of the system which the packet is addressed to. The
mask is in CIDR or slash notation. For example, if you enter
192.168.1.0/24, you are entering the range of 192.168.1.0
to 192.168.1.255.
Destination Port Specify the destination port of the
packet (specified within the packet header). Usually it is
the port of the host system application which the packet is
addressed to.
Comment You can enter a brief description of the
purpose for the firewall rule.
42
Ubiquiti Networks, Inc.
airOSÂŽ v5.6 User Guide
In Bridge mode, all active firewall entries are stored in
the FIREWALL chain of the ebtables filter table. (Ebtables
is a transparent link-layer filtering tool used on bridge
interfaces; this allows the filtering of network traffic
passing through a bridge.)
In Router or SOHO Router mode, all active firewall entries
are stored in the FIREWALL chain of the iptables filter
table.
Action You have the following options:
â˘ Add Add a firewall rule.
â˘ Edit Make changes to a firewall rule. Click Save to save
your changes.
â˘ Del Delete a firewall rule.
Note: Packets are processed by sequentially
traversing the firewall rules.
IPv6 Firewall
(Available in Advanced view.) You can configure IPv6
firewall rules for the local and external network interfaces.
Click the + button to display the IPv6 Firewall section.
Chapter 5: Network
is in CIDR or slash notation. For example, if you enter
2001:db8::/64, you are entering the range of
2001:0db8:0000:0000:0000:0000:0000:0000 to
2001:0db8:0000:0000:ffff:ffff:ffff:ffff.
Source Port Specify the source port of the packet
(specified within the packet header). Usually it is the port
of the host system application that sends the packets.
Destination IP/Mask Specify the destination IP of the
packet (specified within the packet header). Usually it is
the IP of the system which the packet is addressed to. The
mask is in CIDR or slash notation. For example, if you enter
2001:db8::/64, you are entering the range of
2001:0db8:0000:0000:0000:0000:0000:0000 to
2001:0db8:0000:0000:ffff:ffff:ffff:ffff.
Destination Port Specify the destination port of the
packet (specified within the packet header). Usually it is
the port of the host system application which the packet is
addressed to.
Comment You can enter a brief description of the
purpose for the firewall rule.
All active firewall entries are stored in the FIREWALL6
chain of the ebtables filter table.
Action You have the following options:
â˘ Add Add a firewall rule.
Enable Enables firewall functionality.
Enabled Enables the specific firewall rule. All the added
firewall rules are saved in the system configuration file;
however, only the enabled firewall rules are active on the
device.
Target To allow packets to pass through the firewall
unmodified, select ACCEPT. To block packets, select
DROP.
Interface Select the appropriate interface where the
firewall rule is applied. To apply the firewall rule to all
interfaces, select ANY.
IP Type Sets which specific Layer 3 protocol type (IP, ICMP,
TCP, UDP) should be filtered.
â˘ Edit Make changes to a firewall rule. Click Save to save
your changes.
â˘ Del Delete a firewall rule.
Static Routes
(Available in Advanced view.) You can manually add
static routing rules to the system routing table; you can
set a rule that a specific target IP address (or range of IP
addresses) passes through a specific gateway. Click the +
button to display the Static Routes section.
Enabled Enables the specific static route. All the added
static routes are saved in the system configuration file;
however, only the enabled static routes are active on the
device.
Target Network IP Specify the IP address of the
destination.
Netmask Specify the netmask of the destination.
! Can be used to invert the Source IP/Mask, Source Port,
Destination IP/Mask, and/or Destination Port filtering
criteria. For example, if you enable ! (Not) for the specified
Destination Port value 443, then the filtering criteria will
be applied to all the packets sent to any Destination Port
except port 443, which is commonly used by HTTPS.
Comment You can enter a brief description of the
purpose for the static route.
Source IP/Mask Specify the source IP of the packet
(specified within the packet header). Usually it is the
IP of the host system that sends the packets. The mask
â˘ Edit Make changes to a static route. Click Save to save
your changes.
Ubiquiti Networks, Inc.
Gateway IP Specify the IP address of the gateway.
Action You have the following options:
â˘ Add Add a static route.
â˘ Del Delete a static route.
43
Chapter 5: Network
IPv6 Static Routes
(Available in Router or SOHO Router mode only)
(Available in Advanced view.) You can manually add IPv6
static routing rules to the system routing table; you can
set a rule that a specific target IP address (or range of IP
addresses) passes through a specific gateway. Click the +
button to display the IPv6 Static Routes section.
airOSÂŽ v5.6 User Guide
Bursting allows the bandwidth to spike higher than the
maximum bandwidth you configure in the Ingress and
Egress Rate settings â for a short period of time. Once the
Ingress or Egress Burst (volume of data) is used up, the
throughput drops back down to the corresponding Ingress
or Egress Rate setting (maximum bandwidth) you have set.
For example, you have the following conditions:
â˘ Egress Burst is set to 2048 kBytes.
â˘ Egress Rate is set to 512 kbit/s.
â˘ Actual maximum bandwidth is 1024 kbit/s.
Enabled Enables the specific static route. All the added
static routes are saved in the system configuration file;
however, only the enabled static routes are active on the
device.
Bursting allows 2048 kBytes to pass at 1024 kbit/s before
throttling down to 512 kbit/s.
Target Network IP Specify the IP address of the
destination.
Netmask Specify the netmask of the destination. The
mask is in CIDR or slash notation. For example, if you enter
2001:db8::/64, you are entering the range of
2001:0db8:0000:0000:0000:0000:0000:0000 to
2001:0db8:0000:0000:ffff:ffff:ffff:ffff.
Gateway IP Specify the IP address of the gateway.
Comment You can enter a brief description of the
purpose for the static route.
Action You have the following options:
â˘ Add Add a static route.
â˘ Edit Make changes to a static route. Click Save to save
your changes.
â˘ Del Delete a static route.
Enable Enables bandwidth control on the device.
Enabled Enables the specific rule. All the added rules are
saved in the system configuration file; however, only the
enabled rules are active on the device.
Interface Select the appropriate interface.
Ingress
â˘ Enable Enables the ingress values.
â˘ Rate, kbit/s Specify the maximum bandwidth value
(in kilobits per second) for traffic entering the specified
interface.
â˘ Burst, kBytes Specify the data volume (in kilobytes)
that is allowed before the ingress maximum bandwidth
applies.
Traffic Shaping
Egress
(Available in Advanced view.) Traffic Shaping controls
bandwidth from the perspective of the client. In Station
mode only, bursting allows fast downloads when a user
downloads small files (for example, viewing different
pages of a website), but prevents a user from using
excessive bandwidth when downloading large files (for
example, streaming a movie).
â˘ Enable Enables the egress values.
As Layer 3 QoS, you can limit the traffic at the device at
the interface level, based on a rate limit you define. Each
interface has two types of traffic:
â˘ Ingress traffic entering the interface
â˘ Egress traffic exiting the interface
We recommend using Traffic Shaping to control egress
traffic, because it is more efficient in the egress direction.
When an interface accepts ingress traffic, it cannot control
how quickly the traffic arrives â the sending device
controls that traffic. However, when an interface sends out
egress traffic, it can control how quickly the traffic exits.
44
â˘ Rate, kbit/s Specify the maximum bandwidth value
(in kilobits per second) for traffic exiting the specified
interface.
â˘ Burst, kBytes Specify the data volume (in kilobytes)
that is allowed before the egress maximum bandwidth
applies.
Action You have the following options:
â˘ Add Add a rule.
â˘ Edit Make changes to a traffic shaping rule. Click Save
to save your changes.
â˘ Del Deletes a traffic shaping rule.
Ubiquiti Networks, Inc.
airOSÂŽ v5.6 User Guide
Chapter 6: Advanced
Chapter 6: Advanced
The Advanced page handles advanced routing and
wireless settings. Only technically advanced users who
have sufficient knowledge about WLAN technology
should use the advanced wireless settings. These settings
should not be changed unless you know the effects the
changes will have on the device.
Change To save or test your changes, click Change.
A new message appears. You have three options:
â˘ Apply To immediately save your changes, click Apply.
â˘ Test To try the changes without saving them, click
Test. To keep the changes, click Apply. If you do not
click Apply within 180 seconds (the countdown is
displayed), the device times out and resumes its earlier
configuration.
â˘ Discard To cancel your changes, click Discard.
Advanced Wireless Settings
The table displays the available 802.11n data rates:
Chains
Data Rates
1x1
0&6ÂŠÂŠ0&6ÂŠÂŠ0&6ÂŠÂŠ0&6ÂŠ0&6ÂŠÂŠ0&6ÂŠÂŠ0&6ÂŠ
2x2
0&6ÂŠÂŠ0&6ÂŠÂŠ0&6ÂŠÂŠ0&6ÂŠ
MCS 12, MCS 13, MCS 14, MCS 15
Ubiquiti Networks, Inc.
RTS Threshold (If airMAX is enabled, RTS Threshold is not
required.) Determines the packet size of a transmission
and, through the use of an AP, helps control traffic flow.
The range is 0-2346 bytes. The default setting is the value
2346; this means that RTS is disabled.
Note: As an alternative, you can select Off to disable
this option.
The 802.11 wireless networking protocol uses the 802.11
wireless networking Request to Send (RTS)/Clear to Send
(CTS) mechanisms to reduce frame collisions introduced
by the hidden terminal problem. The RTS/CTS packet size
threshold is 0-2346 bytes. If the packet size that the device
wants to transmit is larger than the threshold, then the
RTS/CTS handshake is triggered. If the packet size is equal
to or less than the threshold, then the data frame is sent
immediately.
45
Chapter 6: Advanced
The system uses RTS/CTS frames for the handshake;
this reduces collisions for APs with hidden stations. The
station sends an RTS frame first; the AP responds with a
CTS frame. After the handshake with the AP is completed,
the station sends data. CTS collision control management
has a time interval defined; during this interval, all other
stations do not transmit and wait until the requesting
station finishes transmission.
airOSÂŽ v5.6 User Guide
Multicast Enhancement (Available in Access Point or
AP-Repeater mode only.) If clients do not send IGMP
(Internet Group Management Protocol) messages, then
they are not registered as receivers of your multicast
traffic. Using IGMP snooping, the Multicast Enhancement
option isolates multicast traffic from unregistered
clients and allows the device to send multicast traffic to
registered clients using higher data rates. This lessens the
risk of traffic overload on PtMP links and increases the
reliability of multicast traffic since packets are transmitted
again if the first transmission fails. If clients do not send
IGMP messages but should receive multicast traffic, then
you may need to disable the Multicast Enhancement
option. By default this option is enabled.
Installer EIRP Control (Not available for US products with
fixed antennas.) Allows you to control the Calculate EIRP
Limit setting on the Wireless page.
Distance To specify the distance value in miles (or
kilometers), use the slider or manually enter the value.
The signal strength and throughput fall off with range.
Changing the distance value will change the ACK
(Acknowledgement) timeout value accordingly.
Auto Adjust We recommend enabling the Auto Adjust
option. Every time the station receives a data frame, it
sends an ACK frame to the AP (if transmission errors are
absent). If the station does not receive an ACK frame
from the AP within the set timeout, then it re-sends the
frame. If too many data frames are re-sent (whether the
ACK timeout is too short or too long), then there is a poor
connection, and throughput performance drops.
The device has a new auto-acknowledgement
timeout algorithm, which dynamically optimizes the
frame acknowledgement timeout value without user
intervention. This critical feature is required for stabilizing
long-distance 802.11n outdoor links.
Extra Reporting Reports additional information, such
as device name, in the 802.11 management frames. This
information is commonly used for system identification
and status reporting in discovery utilities and router
operating systems.
Client Isolation (Available in Access Point or AP-Repeater
mode only.) Allows packets to be sent only from the
external network to the CPE and vice versa. If Client
Isolation is enabled, wireless stations connected to the
same AP will not be able to interconnect on both the Layer
2 (MAC) and Layer 3 (IP) levels. This also affects associated
stations and WDS peers as well.
Sensitivity Threshold, dBm Defines the minimum client
signal level accepted by the AP for the client to connect.
If the client signal level subsequently drops, the client
remains connected to the AP.
Advanced Ethernet Settings
If two or more stations are located at considerably
different distances from the AP they are associated with,
the distance to the farthest station should be set on the
AP side.
Aggregation A part of the 802.11n standard that allows
sending multiple frames per single access to the medium
by combining frames together into one larger frame. It
creates the larger frame by combining smaller frames with
the same physical source, destination end points, and
traffic class (QoS) into one large frame with a common
MAC header.
â˘ Frames Determines the number of frames combined in
the new larger frame.
â˘ Bytes Determines the size (in bytes) of the larger frame.
â˘ Enable Check the box to use the Aggregation option.
Multicast Data Allows multicast packets to pass through.
By default this option is enabled.
46
LAN0/1 Speed By default, the option is Auto. The device
automatically negotiates transmission parameters, such as
speed and duplex, with its counterpart. In this process, the
networked devices first share their capabilities and then
choose the fastest transmission mode they both support.
To manually specify the maximum transmission link
speed and duplex mode, select one of the following
options: 100 Mbps-Full, 100Mbps-Half, 10 Mbps-Full,
or 10Mbps-Half. If you are running extra long Ethernet
cables, a link speed of 100ESVÂŠFRXOGÂŠKHOSÂŠWRÂŠDFKLHYHÂŠ
better stability.
Full-duplex mode allows communication in both
directions simultaneously. Half-duplex mode allows
communication in both directions, but not simultaneously
and only in one direction at a time.
Ubiquiti Networks, Inc.
airOSÂŽ v5.6 User Guide
Chapter 6: Advanced
POE Passthrough (Availability is device-specific.) When
enabled, the device allows Power over Ethernet (PoE)
power to pass from the main port to the secondary
port, thereby powering an additional device, such as a
compatible IP camera.
Four LEDs
LED
Default Threshold Value
-94 dBm
-80 dBm
ĂľÂŠG%P
-65 dBm
LED
Default Threshold Value
-94 dBm
Signal (Available if the device supports GPS.) The type of
signal, such as wireless or GPS.
-88 dBm
Thresholds, dBm The number of LEDs is device-specific,
and the default values vary depending on the number of
LEDs. The specified LED will light up if the signal strength
reaches the value set in the field.
-82 dBm
ĂľÂŠG%P
For example, if the device has four LEDs and the signal
strength (on the Main page) fluctuates around -63 dBm,
then the LED threshold values can be set to the following:
ĂľÂŠĂľÂŠĂľÂŠDQGÂŠĂľ
ĂľÂŠG%P
-65 dBm
Signal LED Thresholds
(This feature is not available on all devices.) You can
configure the LEDs on the device to light up when
received signal levels reach the values defined in the
following fields. This allows a technician to easily deploy
an airOS CPE without logging into the device (for example,
for antenna alignment operation).
Six LEDs
Note: The â-â character is outside of the field and
should not be used for the signal strength value
specification.
The following tables list the default threshold values for
devices with two, three, four, or six LEDs.
Two LEDs
LED
Default Threshold Value
-94 dBm
-65 dBm
LED
Default Threshold Value
- 94 dBm
ĂľÂŠG%P
-65 dBm
Three LEDs
Ubiquiti Networks, Inc.

Chapter 6: Advanced
airOSÂŽ v5.6 User Guide
48
Ubiquiti Networks, Inc.
airOSÂŽ v5.6 User Guide
Chapter 7: Services
The Services tab configures system management services:
Ping Watchdog, SNMP, servers (web, SSH, Telnet), NTP,
DDNS, system log, and device discovery.
Change To save or test your changes, click Change.
A new message appears. You have three options:
â˘ Apply To immediately save your changes, click Apply.
â˘ Test To try the changes without saving them, click
Test. To keep the changes, click Apply. If you do not
click Apply within 180 seconds (the countdown is
displayed), the device times out and resumes its earlier
configuration.
Chapter 7: Services
Ping Watchdog
Ping Watchdog sets the device to continuously ping a
user-defined IP address (it can be the Internet gateway,
for example). If it is unable to ping under the user-defined
constraints, then the device will automatically reboot. This
option creates a kind of âfail-proofâ mechanism.
Ping Watchdog is dedicated to continuous monitoring of
the specific connection to the remote host using the Ping
tool. The Ping tool works by sending ICMP echo request
packets to the target host and listening for ICMP echo
response replies. If the defined number of replies is not
received, the tool reboots the device.
â˘ Discard To cancel your changes, click Discard.
Ubiquiti Networks, Inc.
49
Chapter 7: Services
airOSÂŽ v5.6 User Guide
For the purpose of equipment identification, configure the
SNMP agent with contact and location information:
SNMP Agent Enables the SNMP agent.
Ping Watchdog Enables use of Ping Watchdog.
â˘ IP Address To Ping Specify the IP address of the target
host to be monitored by Ping Watchdog.
â˘ SNMP Community Specify the SNMP community
string. It is required to authenticate access to
Management Information Base (MIB) objects and
functions as an embedded password. The device
supports a read-only community string; authorized
management stations have read access to all the objects
in the MIB except the community strings, but do not
have write access. The device supports SNMP v1. The
default SNMP Community is public.
â˘ Ping Interval Specify the time interval (in seconds)
between the ICMP echo requests that are sent by Ping
Watchdog. The default value is 300 seconds.
â˘ Contact Specify the contact who should be notified in
case of emergency.
â˘ Startup Delay Specify the initial time delay (in
seconds) until the first ICMP echo request is sent by Ping
Watchdog. The default value is 300 seconds.
Web Server
â˘ Location Specify the physical location of the device.
The Startup Delay value should be at least 60 seconds
as the network interface and wireless connection
initialization takes a considerable amount of time if the
device is rebooted.
â˘ Failure Count to Reboot Specify the number of ICMP
echo response replies. If the specified number of ICMP
echo response packets is not received continuously,
Ping Watchdog will reboot the device. The default value
is 3.
â˘ Save Support Info This generates a support
information file in case Ping Watchdog reboots the
device.
SNMP Agent
Simple Network Management Protocol (SNMP) is an
application layer protocol that facilitates the exchange
of management information between network
devices. Network administrators use SNMP to monitor
network-attached devices for issues that warrant
attention.
The device contains an SNMP agent, which does the
following:
â˘ Provides an interface for device monitoring using SNMP
The following Web Server parameters can be set:
Web Server By default, HTTP service is enabled.
Secure Connection (HTTPS) By default, the web server
uses secure HTTPS mode.
â˘ Secure Server Port If secure HTTPS mode is used,
specify the TCP/IP port of the web server. The default is
443.
Server Port If HTTP mode is used, specify the TCP/IP port
of the web server. The default is 80.
Session Timeout Specifies the maximum timeout before
the session expires. Once a session expires, you must log
in again using the username and password. The default is
15 minutes.
SSH Server
â˘ Communicates with SNMP management applications
for network provisioning
â˘ Allows network administrators to monitor network
performance and troubleshoot network problems
The following SSH Server parameters can be set:
SSH Server This option enables SSH access to the device.
â˘ Server Port Specify the TCP/IP port of the SSH server.
â˘ Password Authentication If enabled, you must
authenticate using administrator credentials to grant
SSH access to the device; otherwise, an authorized key is
required.
50
Ubiquiti Networks, Inc.
airOSÂŽ v5.6 User Guide
â˘ Authorized Keys Click Edit to import a public key file
for SSH access to the device instead of using an admin
password.
Chapter 7: Services
NTP Client Enables the device to obtain the system time
from a time server on the Internet.
â˘ NTP Server Specify the IP address or domain name of
the NTP server.
Dynamic DNS
- Choose File Click Choose File to locate the new key
file. Select the file and click Open.
Domain Name System (DNS) translates domain names
to IP addresses; each DNS server on the Internet holds
these mappings in its respective DNS database. Dynamic
Domain Name System (DDNS) is a network service that
notifies the DNS server in real time of any changes in the
deviceâs IP settings. Even if the deviceâs IP address changes,
you can still access the device through its domain name.
- Import Imports the file for SSH access.
- Enabled Enables the specific key. All the added keys
are saved in the system configuration file; however,
only the enabled keys are active on the device.
- Type Displays the type of key.
- Key Displays the key.
- Comment You can enter a brief description of the
key.
- Action You have the following option:
â˘ Remove Removes a public key file.
Dynamic DNS If enabled, the device allows
communications with the DDNS server.
â˘ Service Select the appropriate service from the
drop-down menu:
- Save Saves your changes.
â˘ dyndns.org (default)
- Close Discards your changes.
â˘ changeip.com
Telnet Server
â˘ zoneedit.com
â˘ free.editdns.net
â˘ no-ip.com
â˘ noip.com
â˘ freedns.afraid.org
The following Telnet Server parameters can be set:
Telnet Server This option activates Telnet access to the
device.
â˘ dnsmax.com
â˘ thatip.com
â˘ he.net
â˘ Server Port Specify the TCP/IP port of the Telnet server.
â˘ dnsdynamic.org
NTP Client
â˘ ovh.com
Network Time Protocol (NTP) is a protocol for
synchronizing the clocks of computer systems over
packet-switched, variable-latency data networks. You
can use it to set the system time on the device. If the
System Log option is enabled, then the real system time
is reported next to every log entry that registers a system
event.
â˘ dnsexit.com
â˘ dnsomatic.com
â˘ 3322.org
â˘ namecheap.com
â˘ easydns.com
â˘ Host Name Enter the host name of the device to
update it on the DDNS server.
â˘ Username Enter the user name of the DDNS account.
â˘ Password Enter the password of the DDNS account.
â˘ Show Check the box to display the password
characters.
Ubiquiti Networks, Inc.
51
Chapter 7: Services
airOSÂŽ v5.6 User Guide
System Log
Every logged message contains at least the system time
and name of the specific service that generates the
V\VWHPHYHQW
Messages from different services have different contexts
and different levels of detail. Usually error, warning, or
informational system service messages are reported;
however, more detailed debug level messages can also
be reported. The more detailed the system messages
reported, the greater the volume of log messages
generated.
System Log This option enables the registration routine
of system log (syslog) messages. By default it is disabled.
â˘ Remote Log Enables the syslog remote sending
function. System log messages are sent to a remote
server, which is specified in the Remote Log IP Address
and Remote Log Port fields.
- Remote Log IP Address The host IP address that
receives syslog messages. Properly configure the
remote host to receive syslog protocol messages.
- Remote Log Port The TCP/IP port that receives syslog
messages. 514 is the default port for the commonly
used system message logging utilities.
- TCP Protocol Send the system log messages using
the TCP protocol.
Device Discovery
Discovery Enables device discovery, so the device can be
discovered by other Ubiquiti devices through the Device
Discovery tool available through the airOS Configuration
(refer to âDiscoveryâ on page 58) or as a separate
download at: downloads.ubnt.com
CDP Enables Cisco Discovery Protocol (CDP)
communications, so the device can send out CDP packets
to share its information.
52
Ubiquiti Networks, Inc.
airOSÂŽ v5.6 User Guide
Chapter 8: System
The System page contains administrative options. This
page enables the administrator to reboot the device, reset
it to factory defaults, upload new firmware, back up or
update the configuration, and configure the administrator
account.
Chapter 8: System
Firmware Update
This section manages the firmware maintenance.
Change To save or test your changes, click Change.
Firmware Version Displays the current firmware version.
A new message appears. You have three options:
Build Number Displays the build number of the firmware
version.
â˘ Apply To immediately save your changes, click Apply.
â˘ Test To try the changes without saving them, click
Test. To keep the changes, click Apply. If you do not
click Apply within 180 seconds (the countdown is
displayed), the device times out and resumes its earlier
configuration.
â˘ Discard To cancel your changes, click Discard.
Ubiquiti Networks, Inc.
Check for Updates By default, the firmware automatically
checks for updates. To manually check for an update, click
Check Now.
Upload Firmware Click this button to update the device
with new firmware.
The device firmware update is compatible with all
configuration settings. The system configuration is
preserved while the device is updated with a new
firmware version. However, we recommend that you back
up your current system configuration before updating the
firmware.
53
Chapter 8: System
This is a three-step procedure:
1. Click Choose File to locate the new firmware file. Select
the file and click Open.
2. Click Upload to upload the new firmware to the device.
3. The Uploaded Firmware Version is displayed. Click
Update to confirm.
airOSÂŽ v5.6 User Guide
System Accounts
You can change the administrator password to protect
your device from unauthorized changes. We recommend
that you change the default administrator password on
the very first system setup:
If the firmware update is in process, you can close the
firmware update window, but this does not cancel the
firmware update. Please be patient, as the firmware
update routine can take three to seven minutes. You
cannot access the device until the firmware update
routine is completed.
Note: Do not power off, do not reboot, and do
not disconnect the device from the power supply
during the firmware update process as these
actions will damage the device!
Device
The Device Name (host name) is the system-wide device
identifier. The SNMP agent reports it to authorized
management stations. The Device Name will be used in
popular router operating systems, registration screens,
and discovery tools.
Device Name Specifies the host name.
Interface Language Allows you to select the language
displayed in the web management interface. English is the
default language.
You may upload additional language profiles. Refer to our
wiki page at the following URL:
http://wiki.ubnt.com/How_to_import_Language_Profile
Date Settings
Administrator User Name Specifies the name of the
administrator.
Key button Click this button to change the administrator
password.
â˘ Current Password Enter the current password for
the administrator account. It is required to change the
Password or Administrator User Name.
â˘ New Password Enter the new password for the
administrator account. airOS will indicate that the
password is Too Short (text color: brown) if it has fewer
than four characters. As you enter the new password,
airOS will indicate its strength: Weak (red), Normal
(orange), or Strong (green).
Note: The password length is 4 characters minimum
and 63 characters maximum; we recommend using
DWÂŠOHDVWÂŠFKDUDFWHUV
â˘ Verify New Password Re-enter the new password for
the administrator account.
Read-Only Account Check the box to enable the
read-only account, which can only view the Main page.
Configure the username and password to protect your
device from unauthorized changes.
â˘ Read-Only Account Name Specifies the name of the
system user.
â˘ Key button Click this button to change the read-only
password.
- New Password Enter the new password for the
read-only account.
Time Zone Specifies the time zone according to
Greenwich Mean Time (GMT).
- Show Check the box to display the read-only
password characters.
Startup Date When enabled, you are able to change the
deviceâs startup date.
â˘ Startup Date Specifies the deviceâs startup date. Click
the Calendar icon or manually enter the date in the
format determined by the browser locale.
54
Ubiquiti Networks, Inc.
airOSÂŽ v5.6 User Guide
Miscellaneous
Chapter 8: System
Device Maintenance
The controls in this section manage the device
maintenance routines: reboot and support information
reports.
Reset Button To allow use of the reset button, check the
box. To prevent an accidental reset to default settings,
uncheck the box (this also disables the remote POE reset
functionality).
Note: You can reset the device to default settings
through System > Reset to Defaults.
UNII-2 Band This option is available if DFS (Dynamic
Frequency Selection) frequencies in the UNII-2 band
(5.25 - 5.725 GHz) should be available for your device but
are locked. To unlock the DFS frequencies, follow these
instructions:
1. Visit www.ubnt.com/fcclabelrequest and follow the
online instructions to request the activation key and
FCC labels.
2. After you have received your activation key and FCC
labels, check the box next to UNII-2 Band.
3. In the Company Name field, enter the company name
you provided when you requested the activation key.
4. In the Key field, enter the activation key.
Reboot Device Initiates a full reboot cycle of the device.
Reboot is the same as the hardware reboot, which is
similar to the power-off and power-on cycle. The system
configuration stays the same after the reboot cycle
completes. Any changes that have not been applied are
lost.
Support Info This generates a support information
file that the Ubiquiti support engineers can use when
providing customer support. This file only needs to be
generated at their request.
Configuration Management
The controls in this section manage the device
configuration routines and the option to reset the device
to factory default settings.
The device configuration is stored in plain text file (cfg
file). You can back up, restore, or update the system
configuration file:
5. Apply the FCC labels to the appropriate device(s).
airMAX Technology Features (Available on the System
page if the Ubiquiti logo page is not displayed.) airMAX
is Ubiquitiâs proprietary Time Division Multiple Access
(TDMA) polling technology. airMAX offers better tolerance
against interference and increases the maximum number
of users that can associate with an AP that is airMAXcapable.
After you have enabled this setting on the System page,
the Ubiquiti logo page appears. For more information, see
âairMAX Settingsâ on page 15.
Location
Latitude and longitude define the deviceâs coordinates;
they are used to automatically update the deviceâs
location for airOS management.
Latitude The latitude of the deviceâs location is displayed.
Valid values for latitude are -90 to +90.
Back Up Configuration Click Download to download the
current system configuration file.
Note: We strongly recommend that you save
the configuration file in a secure location. The
configuration file includes confidential information,
such as WPA keys in plain text.
Upload Configuration Click Choose File to locate the
new configuration file. Select the file and click Open.
We recommend that you back up your current system
configuration before uploading the new configuration.
Note: Use only configuration files for the same
type of the device. Behavior may be unpredictable
if you mix configuration files from different types
of devices. (For example, upload a RocketM5
configuration file to a RocketM5; do NOT upload a
BulletM5 configuration file to a RocketM5.)
Longitude The longitude of the deviceâs location is
displayed. Valid values for longitude are -180 to +180.
Ubiquiti Networks, Inc.
55
Chapter 8: System
airOSÂŽ v5.6 User Guide
Upload Click this button to upload the new configuration
file to the device. Click Apply to confirm.
After the device reboots, the settings of the new
configuration are displayed in the Wireless, Network,
Advanced, Services, and System tabs of the web
management interface.
Reset to Factory Defaults Resets the device to the
factory default settings. This option will reboot the
device, and all factory default settings will be restored.
We recommend that you back up your current system
configuration before resetting the device to its defaults.
56
Ubiquiti Networks, Inc.
airOSÂŽ v5.6 User Guide
Chapter 9: Tools
Each page of the airOS interface contains network
administration and monitoring tools. Click the Tools
drop-down list at the top right corner of the page.
Align Antenna
Use the Align Antenna tool to point and optimize the
antenna in the direction of maximum link signal. The
Antenna Alignment window reloads every second.
Chapter 9: Tools
Alignment Beep You can enable the audio option so
a technician can easily align the antenna of an airMAX
device without looking at the airOS Configuration
Interface. The higher the pitch, the stronger the signal
strength. Each rise in pitch correlates to an increase in the
received signal level, which is represented by a color in the
airOS Configuration Interface:
â˘ Red (weakest received signal level)
â˘ Yellow
â˘ Green
â˘ Blue (strongest received signal level)
Site Survey
The Site Survey tool searches for wireless networks in range
on all supported frequencies.
Signal Level Displays the signal strength of the last
received packet.
Vertical/Horizontal Displays the wireless signal level (in
dBm) of each polarity, if there is more than one polarity.
(The number of polarities is device-specific.)
Noise Level Displays the background noise level (in dBm)
when the wireless signal is received.
Max Signal Displays the maximum signal strength (in
dBm). Use the slider to adjust the range of the Signal
Level meter to be more sensitive to signal fluctuations (it
changes an offset of the maximum indicator value).
Scanned Frequencies In Station mode, you can change
the frequency list; for details, see âFrequency Scan List,
MHzâ on page 26.
After the search is completed, the Site Survey tool reports
the following for each result:
MAC Address Displays the MAC address of the wireless
interface of the device.
SSID Displays the wireless network name.
Device Name Displays the host name or identifier of the
device.
Ubiquiti Networks, Inc.
57
Chapter 9: Tools
Radio Mode Displays the technology used by the device.
Encryption Displays the encryption method used by the
device (if any).
Signal/Noise, dBm Displays the signal strength and noise
levels, in dBm.
airOSÂŽ v5.6 User Guide
Ping
You can ping other devices on the network directly from
the device. The Ping tool uses ICMP packets to check the
preliminary link quality and packet latency estimation
between two network devices.
Frequency, GHz/Channel Displays the frequency in GHz
and channel in use.
To refresh the window, click Scan.
Discovery
The Device Discovery tool searches for all Ubiquiti devices
on your network.
Network Ping
Select Destination IP You have two options:
Search As you enter keywords, the Search field
automatically filters devices containing specified names or
numbers.
After the search is completed, the Discovery tool reports
the following for each result:
MAC Address Displays the MAC address or hardware
identifier of the device.
Device Name Displays the host name or identifier of the
device.
Mode Displays the operating mode of the wireless
device, AP or STA (Station). If the device is not wireless (for
example, a UniFi Video Camera), then â-â is displayed.
â˘ Select a remote system IP from the drop-down list,
which is generated automatically.
â˘ Select specify manually and enter the IP address in the
field displayed below.
Packet Count Enter the number of packets to send for
the ping test.
Packet Size Specify the size of the packet.
Start Click this button to start the test.
After the test is completed, the Ping tool reports the
following information for each packet sent:
Host Displays the host name or identifier.
SSID Displays the wireless network name.
Time Displays the round-trip time.
Product Displays the product name or type of the device.
TTL Displays the Time To Live (TTL), the number of hops
allowed before the ping test fails.
Firmware Displays the version number of the firmware.
IP Address Displays the IP address of the device.
To access a device configuration through its web
management interface, click the deviceâs IP address.
To refresh the window, click Scan.
The Ping tool reports packet loss statistics and round-trip
time evaluation:
Packets Received Displays the number of packets
received.
Loss Displays the percentage of packets lost.
Min. Displays the minimum round-trip time in
milliseconds.
Avg. Displays the average round-trip time in milliseconds.
Max. Displays the maximum round-trip time in
milliseconds.
58
Ubiquiti Networks, Inc.
airOSÂŽ v5.6 User Guide
Chapter 9: Tools
Traceroute
Speed Test
The Traceroute tool traces the hops from the device to
a specified IP address. Use this tool to find the route
taken by ICMP packets across the network to a specified
destination host name or IP address.
This utility allows you to test the connection speed
between two airOS devices that are using firmware
version 5.2 or above. You can use Speed Test to estimate a
preliminary throughput between two network devices.
Note: If traffic shaping is enabled on either
device, then the Speed Test results will be limited
accordingly.
Destination Host Enter the host name or IP address of
the destination host.
Resolve IP Addresses Select this option to resolve the
hop addresses symbolically rather than numerically.
Start Click this button to start the test.
After the test is completed, the Traceroute tool reports the
following information for each hop:
# Displays the hop number.
Host Displays the host name, identifier, or IP address of
the hop host.
IP Displays the IP address of the hop host.
Responses Displays the round-trip times from the device
to the hop host. There are three packets sent per hop, so
there should be three round-trip times displayed. If there
is no response from the hop host within the timeout
interval of 5 seconds, then â*â is displayed.
Select Destination IP You have two options:
â˘ Select a remote system IP from the drop-down list,
which is generated automatically.
â˘ Select specify manually and enter the IP address in the
field displayed below.
User Enter the administrator username.
Note: Enter the remote system access credentials
required for communication between two airOS
devices. Administrator username and password are
required to establish the TCP/IP-based throughput
test.
Password Enter the administrator password.
Remote WEB port Enter the remote web port of the
airOS device to establish a TCP/IP-based throughput test
(for example, specify port 443 if HTTPS is enabled in the
remote device). The default is 80.
Show Advanced Options Enables additional Speed Test
utility options.
Direction Select one of three directions:
â˘ duplex Estimates the incoming (RX) and outgoing (TX)
throughput at the same time.
â˘ receive Estimates the incoming (RX) throughput.
â˘ transmit Estimates the outgoing (TX) throughput.
Duration Enter the number of seconds the test should
last. The default is 30 seconds.
Run Test Click this button to start the test.
Test Results Displays three result categories:
â˘ RX Displays the estimated incoming throughput.
â˘ TX Displays the estimated outgoing throughput.
â˘ Total Displays the aggregate throughput.
Ubiquiti Networks, Inc.
59
Chapter 9: Tools
airView
Use the airView Spectrum Analyzer to analyze the noise
environment of the radio spectrum and intelligently select
the optimal frequency to install a PtP airMAX link.
There are two system requirements for the airView
Spectrum Analyzer:
â˘ Your system is connected to the device via Ethernet.
Launching airView will terminate all wireless
connections on the device.
â˘ Java Runtime Environment 1.6 (or above) is required on
your client machine to use airView.
On first use, the following window appears.
airOSÂŽ v5.6 User Guide
Main View
Device Displays the device name, MAC (Media Access
Control) address, and IP address of the device running
airView.
Total RF Frames Displays the total number of Radio
Frequency (RF) frames gathered since the start of the
airView session or since the Reset All Data button was last
clicked.
FPS Displays the total number of frames per second (FPS)
gathered since the start of the airView session or since
the Reset All Data button was last clicked. The wider the
interval amplitude, the fewer the FPS will be gathered.
Reset All Data Click to reset all gathered data. Use this
option to analyze the spectrum for another location or
address.
File Menu
Click Exit to end the airView session.
â˘ Do NOT warn me about this in the future Check the
box to bypass this window in future launches of the
airView Spectrum Analyzer.
View Menu
â˘ Launch airView Click Launch airView to download the
Java Network Launch Protocol (jnlp) file and complete
the launch of airView.
Enable Chart Panel 1 (top) Displays the Waterfall or
Channel Usage chart in Chart Panel 1, depending on
which option you have selected in Preferences. This
time-based graph shows the aggregate energy collected
or channel usage for each frequency since the start of the
airView session.
Enable Chart Panel 2 (middle) Displays the Waveform
chart in Chart Panel 2. This time-based graph shows the RF
signature of the noise environment since the start of the
airView session. The energy color designates its amplitude.
Cooler colors represent lower energy levels (with blue
representing the lowest levels) in that frequency bin, and
warmer colors (yellow, orange, or red) represent higher
energy levels in that frequency bin.
Enable Chart Panel 3 (bottom) Displays the Real-time
chart (traditional spectrum analyzer) in Chart Panel 3.
Energy (in dBm) is shown in real time as a function of
frequency.
Note: Energy is the power ratio in decibels (dB) of
the measured power referenced to one milliwatt
(mW).
Clear All Markers Resets all previously assigned
markers. Markers are assigned by clicking a point, which
corresponds with a frequency on the Real-time chart.
60
Ubiquiti Networks, Inc.
airOSÂŽ v5.6 User Guide
Preferences Changes airView settings, such as enabling
or disabling charts and traces, or specifying the frequency
interval.
Preferences
Select View > Preferences to display the Preferences airView Spectrum Analyzer window.
Charts
Chapter 9: Tools
â˘ Channel Usage For each Wi-Fi channel, a bar displays
a percentage showing the relative âcrowdednessâ of
that specific channel. To calculate this percentage, the
airView Spectrum Analyzer analyzes both the popularity
and strength of RF energy in that channel since the start
of an airView session.
Enable Waveform chart (middle) Check the box to
enable the middle chart. This time-based graph shows
the RF signature of the noise environment since the
start of the airView session. The energy color designates
its amplitude. Cooler colors represent lower energy
levels (with blue representing the lowest levels) in that
frequency bin, and warmer colors (yellow, orange, or red)
represent higher energy levels in that frequency bin.
The spectral view over time will display the steady-state RF
energy signature of a given environment.
Enable Real-time chart (bottom) Check the box to
enable the bottom chart. This graph displays a traditional
spectrum analyzer in which energy (in dBm) is shown in
real time as a function of frequency. There are three traces
in this view:
â˘ Current (Yellow) Shows the real-time energy seen by
the device as a function of frequency.
â˘ Average (Green) Shows the running average energy
across frequency.
â˘ Maximum (Blue) Shows updates and maximum power
levels across frequency.
Realtime Traces
Enable top chart Check the box to enable the top chart.
Select the desired chart to display in the top chart panel
on the main view. There are two options:
â˘ Waterfall This time-based graph shows the aggregate
energy collected for each frequency since the start
of the airView session. The energy color designates
its amplitude. Cooler colors represent lower energy
levels (with blue representing the lowest levels) in that
frequency bin, and warmer colors (yellow, orange, or
red) represent higher energy levels in that frequency
bin.
The Waterfall Viewâs legend (top-right corner) provides
a numerical guide associating the various colors to
power levels (in dBm). The low end of that legend (left)
is always adjusted to the calculated noise floor, and the
high end (right) is set to the highest detected power
level since the start of the airView session.
Ubiquiti Networks, Inc.
61
Chapter 9: Tools
airOSÂŽ v5.6 User Guide
The following settings apply only to the Real-time chart:
Current Real-time Trace Check the Enable box to enable
the real-time trace. When enabled, the yellow outline on
the Real-time chart represents the real-time power level of
each frequency. The refresh speed depends on the FPS.
Averages Trace Check the Enable box to enable the
averages trace. When enabled, the averages trace is
represented by the green area on the Real-time chart,
which displays the average received power level data
since the start of the airView session. To enable a shaded
green area, check the Shaded Area box. To display only
a green outline without the shaded area, uncheck the
Shaded Area box.
Maximum Power Levels Trace Check the Enable box to
enable the maximum power trace. When enabled, the
maximum power trace is represented by the blue area on
the Real-time chart, which displays the maximum received
power level data since the start of the airView session. To
enable a shaded blue area, check the Shaded Area box.
To display only a blue outline without the shaded area,
uncheck the Shaded Area box.
Frequency Range Select the amplitude of the
frequency interval to be scanned from the Frequency
Range drop-down list. Available frequencies are devicedependent. There are pre-defined ranges for the most
popular bands. You can enter a custom range; select
Custom Range from the Frequency Range drop-down list
and enter the desired values in the Start and End fields.
Help
Click About to view the version and build number of the
airView Spectrum Analyzer.
62
Ubiquiti Networks, Inc.
airOSâ˘ Controller User Guide
Appendix A: Contact Information
Appendix A: Contact
Information
Ubiquiti Networks Support
Ubiquiti Support Engineers are located around the world
and are dedicated to helping customers resolve software,
hardware compatibility, or field issues as quickly as
possible. We strive to respond to support inquiries within
a 24-hour period.
Ubiquiti Networks, Inc.
2580 Orchard Parkway
San Jose, CA 95131
www.ubnt.com
Online Resources
Support: support.ubnt.com
Community: community.ubnt.com
Downloads: downloads.ubnt.com
JL071515
Ubiquiti Networks, Inc.
63
ÂŠ 2012-2015 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, Ubiquiti Networks, the Ubiquiti U logo, the Ubiquiti beam logo, airControl, airGateway,
airGrid, airMAX, airOS, airRouter, airSelect, airSync, airView, Bullet, NanoBeam, NanoBridge, NanoStation, PicoStation, PowerBeam, PowerBridge, Rocket, and
WispStation are trademarks or registered trademarks of Ubiquiti Networks, Inc. in the United States and in other countries. WPA and WPA2 are trademarks of
WKHÂŠ:LĂľ)LÂŠ$OOLDQFHÂŠ$OOÂŠRWKHUÂŠWUDGHPDUNVÂŠDUHÂŠWKHÂŠSURSHUW\ÂŠRIÂŠWKHLUÂŠUHVSHFWLYHRZQHUVÂŠ

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : J Lee
Create Date                     : 2017:02:13 17:52:56+08:00
Modify Date                     : 2017:02:13 17:52:56+08:00
XMP Toolkit                     : Adobe XMP Core 5.6-c015 84.159810, 2016/09/10-02:41:30
Format                          : application/pdf
Title                           : airOS v5.6 User Guide
Creator                         : J Lee
Rights                          : © 2012-2015 Ubiquiti Networks, Inc. All rights reserved.
Subject                         : airMAX, airOS, Rocket, NanoBeam, NanoStation, NanoBridge, Bullet, PicoStation, PowerBridge, PowerBridge, airGrid, WispStation, Ubiquiti Networks
Metadata Date                   : 2016:10:25 09:57:14-07:00
Creator Tool                    : Adobe InDesign CC 2015 (Macintosh)
Instance ID                     : uuid:c6f9f3fe-26ce-4455-a8ff-b2a1c67d3737
Original Document ID            : xmp.did:0C619F54242068118C14B68B230AF762
Document ID                     : xmp.id:f38a5bb9-083c-4aa3-a0e6-74ab1ac775fa
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:c8ce0c88-5701-4cc5-bde3-2b9b8bb70c21
Derived From Document ID        : xmp.did:5D6B9DFD132068118C14F1B2898B6B19
Derived From Original Document ID: xmp.did:0C619F54242068118C14B68B230AF762
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 2015 (Macintosh)
History Changed                 : /
History When                    : 2015:07:23 15:40:26-07:00
Producer                        : Acrobat Distiller 15.0 (Windows)
Trapped                         : False
Page Count                      : 68

EXIF Metadata provided by EXIF.tools

Ubiquiti ISM5 IsoStation M5 User Manual airOS v5 6 User Guide

Ubiquiti Networks, Inc. IsoStation M5 airOS v5 6 User Guide

Contents

OSG

FCC ID Filing: SWX-ISM5

Navigation menu

Namespaces

Views

Navigation