UNISTRONG SCIENCE and TECHNOLOGY UT30 Rugged Tablet User Manual user manual

Shenzhen UniStrong Science & Technology Co.,Ltd. Rugged Tablet user manual

Contents

user_manual

UT30 Quickstart guide
2.Battery Charging
• Charge with travel charger
Insert the small plug end of the USB data cable into the TYPE-C port
of the device, insert the large plug end of the USB data cable into the
travel charger plug, and then insert the travel charger plug into a
power outlet to charge.
Charge with USB data cable
Connect the cable and the device with USB type-c interface, and plug
in the other end with adapter.
Note: During normal charging, the home screen status bar will display
the charging icon when screen is on.
When the charging is completed, the home screen status bar will display
the full battery icon when screen is on.
3. Insert SIM card, memory card and battery
Power off the device before installing or removing the SIM card, MicroSD
card or battery.
Flip the device to its rear, follow the directions shown in Figure 1 and
push the back cover lock to the open position, and remove the battery
cover. Install the SIM card and MicroSD card according to the battery
compartment label instructions, as shown in Figure 2.
Picture 1 Picture 2
Face the SIM card metal contacts downwards and push into the slot.
Take note on the direction of the notched corner.
Face the MicroSD card metal contacts downwards and push into the
slot. Take note on the direction of the notched corner.
Align the contacts of the battery with the terminals of the battery
compartment and put in the battery gently.
After the battery is installed, replace the battery compartment
cover and push the back cover lock to locked position to secure the
battery compartment cover.
4. Turning the device on and off
To turn on the device, firmly press and hold the bottom right【Power
Button】until the boot screen appears.
To turn off the device, firmly press and hold the 【Power Button】 to
display the options menu. Select the Power off option to shutdown.
With the device turned on, press the 【Power Button】to turn off the
screen and go into sleep mode; Press the 【Power Button】 again to
wake the device, swipe upwards on the screen to unlock; If the device
has been idle for a period of time, the screen will automatically turn off
and go into sleep mode.
5. Home screen operation
From the home screen, you can view the device status and access the
applications. The home screen can have multiple panels; Swipe left or
right on the screen to view each panel.
At the top of the home screen is the status bar, which contains the
notification area, the status area and the display area; the shortcut panel
is at the bottom.
Using the notification panel
When new notification icons appear in the notification area of the status
bar, hold the status bar and drag down to open the notification panel; To
hide the panel, drag the bottom border of the panel upwards.
Customize the shortcut panel
You can customize the shortcuts at the bottom of the home screen by
adding or removing “Shortcut Icons”.
To remove the “Shortcut icon”, press and hold the “Shortcut icon” and
drag it to the “Delete icon”. To add a “Shortcut icon”, press and hold the
icon on the home screen and drag it to the Shortcut panel.
Using applications
Slide the screen left and right to see all the included applications.
Touch the [Home button] below the screen to close it and return to the
home screen.
Expanding the home screen
Swipe your finger horizontally on the home screen to expand to the left
or right of the home screen.
Adding an icon on the home screen
Press and hold any application or widget icon and drag it to an empty
area on the home screen.
Moving icons on the home screen
Press and hold the icon on the home screen and drag the icon to the
desired location on the screen.
Removing icons on the home screen
Press and hold the home screen icon and drag the icon to the "Delete"
icon until the icon turns red.
Create folder
On the home screen, folders are automatically formed when you drag an
icon onto another icon.
Touch the new folder on the screen to open it.
Click on the folder’s label to rename it.
Changing the home screen wallpaper
Press and hold a blank area on the home screen or touch the [Menu
button] → "Wallpaper" to change the home screen wallpaper by
selecting options such as wallpaper, live wallpaper, gallery, etc.
6. Connecting to a computer
Use the USB data cable to connect the device to the computer, pull down
the top status bar, and you can see the message "Connected as a media
device" in the notification area. Clicking on that notification bar will bring
up 3 options "Media device", "Camera" and "Charging mode", which can
be selected according to your needs. Select "Media device" mode to
transfer files between the device and the computer.
If you need to remove the MicroSD card when the device is turned on,
slide the screen to the left or right "→ Settings, or touch the [Menu
button] → "System Settings", go into the Settings panel, scroll down
the screen, and then select "Save"→"Uninstall SD Card".
7. Installation and management of applications
Users can enter the applications store to download and install related
application programs.
Slide the screen left or right → "Settings", select "Apps", or touch the
[Menu button] → "Manage apps" to view and manage application
programs on your device.
8. Using Beidou/GPS positioning function
Slide the screen left and right → "Settings", select "Location
Information" to go into the location service panel, turn on the location
information switch.
In the "Satellite Positioning Mode" option, select GPS + BDS or GPS +
GLONASS or BDS options as needed.
The meaning of the following 2 options:
The NMEA switch turns on the NMEA data output function, which
requires the use of a dedicated data line.
SBAS: To use differential positioning.
The user can view the status of the BeiDou Satellite, GPS satellites and
GLONASS satellites at the current position through an application with
the corresponding functions. The program can display real-time
information such as the serial number, signal strength, position of the
satellite, etc. at the current position.
After the location service is turned on, the applications downloaded and
installed from the applications store can obtain the current location
information and provide location-related services and applications
through the corresponding service interfaces.
Note: "Satellite Positioning Mode" "SBAS" is only supported in certain
models.
9. Camera and videos
Slide the screen left and right → ”Camera”, to turn on the camera, the
screen orientation will change according to how the device is held.
Use two fingers to make a gesture of zooming in or zooming out on the
subject.
Touch the camera switch icon on the top middle part of the screen to
select the front or rear camera.
Touch the button at the bottom right of the screen to switch between
taking photos and videos.
After taking a photo or video, tap the gallery button at the bottom left of
the screen to share, delete, edit or other operations.
9. Mobile network connection (WLAN/Bluetooth)
• WLAN connection
Slide the screen left or right → "Settings" to go into the settings panel,
go to the WLAN options and turn the "On" switch to activate WLAN.
After WLAN is turned on, the WLAN icon will be displayed in the status
bar. Select the connection to be used from the list of available networks
and follow the prompts to enter the network key to connect.
• Bluetooth connection
(1) Activate Bluetooth Slide the screen left or right → "Settings", go into
the Settings panel, go to the Bluetooth option and turn on the "on"
switch to activate Bluetooth. After Bluetooth is turned on, a Bluetooth
icon is displayed in the status bar.
(2) Bluetooth pairing The system will search for connectable Bluetooth
devices in the list of available devices. Click on the Bluetooth device you
want to connect to, enter the Bluetooth password when "Bluetooth
pairing request" pops up, and select pairing. When the owner of the
external Bluetooth device accepts the connection or enters the same
password, the connection to the external device is completed.
(3) Bluetooth transmission Photos, videos and music files can be shared
with family members and friends via Bluetooth.
• Mobile network connection
Slide the screen left or right → "Settings", "More", go to Wireless and
Network panel. Select "VPN" to make the relevant settings.
Notice
This device is restricted to indoor use where operated in the European
Community using frequency in 5150MHz ~ 5250MHz to reduce the potential
for interference. Restriction in BE, BG, CZ, DK, DE, EE, IE,
ES, FR, HR, IT, CY,LV,LT,LU,HU,MT,NL,AT, PL, PT, RO, SI, SK, FI, SE,
UK.
Do not change antenna types ,just only allowed to use Original configuration antenna (FPC)
PRODUCT SAFETY WARNINGS
Use responsibly. Read all instructions and safety information before use to avoid injury. The
maximum operating ambient temperature of the equipment is 55°C .
①Battery safety
Battery works at ambient temperatures ranging from -20°C to 55°C .
(1)CAUTION: Risk of explosion if battery is replaced incorrectly. Replace with the same or
equivalent type of battery as recommended by the manufacturer. Dispose used batteries
according to battery manufacturer’s instructions.
Note: Charging temperature specifications is from 0°C to 45°C .
②Charger safety
Please place the device in an environment that has a normal room temperature with good
ventilation when charging. It is recommended to charge the device in an environment with an
ambient temperature that ranges from 5°C ~40°C
③Wi-Fi Safety
Turn Wi-Fi off in areas where Wi-Fi use is prohibited or when it may cause interference or danger,
such as in airplanes while flying.
④Avoid damage to your hearing
Exposure to loud volumes from earphones and headphones over prolonged periods can cause
hearing loss.
Notice
1. Some special places, such as airports, hospitals, gas stations and other places, do not
allow the use of electronic equipment. Please comply with the rules and do not use this product
in these places.
2. For your safety and the safety of others, please do not use this product while driving
a vehicle.
3. In order to avoid potential safety problems, do not put this product near the vehicle's
airbag.
4. For your safety, please do not use this product during thunderstorms.
5. Although this product is waterproof, do not leave this product for long periods of time in
areas with water or moisture.
6. This product has an operating temperature range of -20°C~+55°C and a storage
temperature range of -40°C~+70°C. Extreme temperatures can affect the device's
performance and service life.
7. Please use an original rechargeable lithium battery. Low-quality batteries will affect the
performance and service life of the device, and may even have the danger of explosion.
8. Although the product has been tested to withstand harsh operating environments, do use
the product in an improper manner.
9. Please do not disassemble this product. In case of failure, please send to our authorized
service centres to proceed with repairs.
10. After the device has reached the end of its service life, please discard in a proper way to
avoid environmental pollution.
11. When replacing the battery or during the use of an external power supply, shut down the
device completely before removing the battery or disconnecting the external power supply to
prevent damage.
12. This product is a Class B product, which may cause radio interference. The user may be
required to take necessary preventive measures.
Battery Instructions
1. This product uses a rechargeable lithium battery as a power source. When the power is
low, please charge the battery. To maintain battery life, it is recommended to deplete the
battery's power before charging.
2. When the battery charger is not in use, please remove it from the power supply. Do not
connect the charger to the battery for more than one week. Excessive charging will shorten the
battery life.
3. Temperature affects the battery charging limit. Therefore, the battery may need to be
cooled or warmed up before charging.
4. Please use the battery for its original intended purpose to prevent short-circuiting the
battery. A short circuit will occur when a conductive material connects the battery’s positive and
negative terminals.
5. Do not use a battery that is damaged.
6. Placing the battery in extremely cold or hot places will lead to shortened battery life.
Exposing the battery to extreme temperatures may cause the phone to malfunction, even if the
battery is fully charged.
7. Do not put the battery in a fire. Please discard the battery in a proper manner or take the
battery to a battery recycling station. Please dispose waste batteries in accordance with local laws
and regulations.
NOTICE:
The SAR limit of Europe is 2.0 W/kg. Device types UT30 has also been tested against this SAR limit.
The highest SAR value reported under this standard during product certification for use on the
body is 0.977W/kg This device was tested for typical body - worn operations with the back of
the handset kept 0 cm from the body. To maintain compliance with RF exposure requirements,
use accessories that maintain a 0 cm separation distance between the user's body and the back
of the handset. The use of belt clips, holsters and similar accessories should not contain
metallic components in its assembly. The use of accessories that do not satisfy these
requirements may not comply with RF exposure requirements, and should be avoided.
Working Temperature: -20℃ ~ +55℃
Storage Temperature: -40℃ ~ +70℃
Charging mode need to operate indoors, please pay attention to the environment temperature
should be 0℃ ~ +45℃
CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED
BATTERIES ACCORDING TO THE INSTRUCTIONS
Hereby, [Shenzhen UniStrong Science & Technology Co.,Ltd.] declares that the radio equipment
type [UT30] is in compliance with Directive 2014 / 53 /EU.
The full text of the EU declaration of conformity is available at the following internet address:
http://en.unistrong.com/declaration.html
This device complies with Part 22 & 24 and Part 27 of the FCC Rules.
SAR INFORMATION
The SAR limit of FCC and ISED is 1.6 W/kg averaged over one gram of tissue. Device types UT30
( FCC ID:2AOPD-UT30 and IC: 11546A-UT30 ) has also been tested against this SAR limit. The
highest SAR value reported under this standard during product certification for use on the body is
1.047 W/kg. This device was tested for typical body -worn operations with the back of the
handset kept 0 cm from the body. To maintain compliance with FCC and ISED RF exposure
requirements, use accessories that maintain a 0 cm separation distance between the user's body
and the back of the handset. The use of belt clips, holsters and similar accessories should not
contain metallic components in its assembly. The use of accessories that do not satisfy these
requirements may not comply with FCC and ISED RF exposure requirements, and should be
avoided.
NOTICE:
This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne
doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radio électrique subi, m ême si le brouillage est susceptible d'en compromettre le
fonctionnement.
NOTICE:
Changes or modifications made to this equipment not expressly approved by Shenzhen UniStrong
Science & Technology Co.,Ltd. may void the FCC authorization to operate this equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installe d and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
NOTICE:
This Class [B] digital apparatus complies with Canadian ICES -003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB - 003 du Canada.
RF mode and power tune-up refer to appendix A
UniStrong APAC Pte Ltd
51 Ubi Ave 1 #01-22 Paya Ubi Industrial Park Singapore 408933 +65 62968238

Navigation menu