Universal Electronics 5300 (Helix) UEI Z-wave 5 Device Remote 2007 User Manual Part 1

Universal Electronics Inc (Helix) UEI Z-wave 5 Device Remote 2007 Users Manual Part 1

UserManual.wiki >

Universal Electronics >

5300 User Manual >

Users Manual Part 1 HTML Version

1. Users Manual Part 1
2. Users Manual Part 2

Users Manual Part 1

Helix Z-wave 5-Device

Remote Control with Learning

Users Guide

Helix 5 Device.fm Page 1 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

TABLE OF CONTENTS

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Features and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Key Charts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Device Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Installing Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Programming Device Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Setting Up a Combo Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Searching for Your Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Checking the Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Using Learning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Learning Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Programming a Learned Key . . . . . . . . . . . . . . . . . . . . . . . . . 14

Deleting a Single Learning Key. . . . . . . . . . . . . . . . . . . . . . . . 15

Deleting All Learned Keys in a Specific Mode . . . . . . . . . . . . 16

Programming Channel Control Lock . . . . . . . . . . . . . . . . . . . . . . . . 16

Unlocking Channel Control. . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Locking Channel Control to SAT . . . . . . . . . . . . . . . . . . . . . . . 17

Changing Volume Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Unlocking Volume Control for a Single Device (Individual

Volume Unlock) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Unlocking All Volume Control (Global Volume Unlock) . . . . . 18

Locking Volume Control To One Mode (Global Volume Lock) 18

Programming ID Lock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Programming a Macro Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Programming a Macro Key. . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Clearing a Macro Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Using the Master Power Key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Programming the Master Power Key . . . . . . . . . . . . . . . . . . . 21

Using the Master Power Key. . . . . . . . . . . . . . . . . . . . . . . . . . 21

Clearing the Master Power Key . . . . . . . . . . . . . . . . . . . . . . . 22

Re-Assigning Device Keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Adding a Node to Your Z-wave Network . . . . . . . . . . . . . . . . . . . . . . 23

Adding a Node to the Network . . . . . . . . . . . . . . . . . . . . . . . . 23

Deleting a Node from the Network. . . . . . . . . . . . . . . . . . . . . 24

Setting Up Scenes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Adding a Node to a Scene. . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Removing a Node from a Scene . . . . . . . . . . . . . . . . . . . . . . . 25

Deleting a Scene. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Controlling Scenes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Helix 5 Device.fm Page 2 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

Transferring Node and Network Information to a Secondary remote .

Transferring Network Information to a Secondary remote . . . . . . . 27

Primary Controller Shift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Controller Copy Receipt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Network Reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Network Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Network Recovery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Removing a Failed Node from the Network . . . . . . . . . . . . . . . . . . . 30

Clearing Custom Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

FCC Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Additional Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Manufacturer’s Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Setup Codes for Audio Amplifiers. . . . . . . . . . . . . . . . . . . . . . 34

Setup Codes for Audio Receivers. . . . . . . . . . . . . . . . . . . . . . 35

Setup Codes for Audio Accessories . . . . . . . . . . . . . . . . . . . . 38

Setup Codes for Cable Boxes/Converters . . . . . . . . . . . . . . . 38

Setup Codes for CD Players . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Setup Codes for DBS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Setup Codes for DVD Players . . . . . . . . . . . . . . . . . . . . . . . . . 41

Setup Codes for DVD/PVR Combos. . . . . . . . . . . . . . . . . . . . . 44

Setup Codes for DVR/PVR Systems . . . . . . . . . . . . . . . . . . . . 49

Setup Codes for Home Automation . . . . . . . . . . . . . . . . . . . . 46

Setup Codes for Satellite Receivers . . . . . . . . . . . . . . . . . . . 46

Setup Codes for TVs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Setup Codes for TVs (DLP) . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Setup Codes for TVs (LCD) . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Setup Codes for TV/DVD Combos . . . . . . . . . . . . . . . . . . . . . . 62

Setup Codes for TV/VCR Combos . . . . . . . . . . . . . . . . . . . . . . 64

Setup Codes for VCRs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Helix 5 Device.fm Page 3 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

INTRODUCTION

The Helix Z-wave 5-Device Remote Control with

Learning by Universal Electronics is our latest

generation universal remote control. Its sophisticated

technology allows you to consolidate up to five of your

original home entertainment remote controls into one

easy-to-use product.

Your remote lets you control individual Z-wave devices

with one easy-to-use, compact unit. You can also set up

and control different groups and scenes.

You can control your electric lights, turning them on or

off, or making them brighter or dimmer.

Moreover, its packed with advanced features such as:

• Preprogrammed control to operate thes satellite

receiver supplied by your service provider

• Dedicated keys to control popular functions on your

DVR/PVR (Digital/Personal Video Recorder)

• Programmable Master Power key for master on/off

control of your home entertainment equipment with

a single keystroke

• Programmable Macro Keys to allow you to activate

certain keys in a specific order

• Channel Lock to lock channel selection only to the

cable converter

• Volume Lock to lock volume controls to one mode or

individual modes

• Device Key Re-Assignment to remotely control a

second (duplicate) device

• Code Search to help program control of older or

discontinued components

• Color-coded keys to quickly locate popular

functions

• Code library for popular video and audio devices

Before using the product, you will need to install the

enclosed batteries and also perform some programming

to operate the specific home entertainment devices you

wish to control.

Please follow the instructions detailed in this manual to

set up the unit and then start enjoying your new remote

control and cable service.

Helix 5 Device.fm Page 4 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

FEATURES AND FUNCTIONS

Use the illustration below to locate features on the Helix

Z-wave 5-Device Remote Control with Learning and

then study the Key Charts (on the next three pages) to

learn how they function.

To find out what type of devices can be controlled by

each device key after programming, see “Device Table”

on page 7 .

Helix 5 Device.fm Page 5 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

Key Charts

Key Function

Use SETUP for all programming

sequences. Also use to turn

backlighting on and off, if applicable.

Press POWER once to turn on or off a

home entertainment device. For

MASTER POWER control, see “Using the

Master Power Key” on page 21.

Press TV, DVD/VCR, SAT, or AUX once to

select a home entertainment device to

control. Also see “Device Table” on

page 7.

Each device key has an embedded LED

(red light) that blinks upon selection

and indicates the remote control is

working and (after programming) is

sending signals.

Use ALL/GUIDE to display the program

guide.

Use INFO to display the current channel

and program information.

Use the Cursor keys to move the cursor

in the program guide and menu screens

and to navigate within the interactive

service.

Use OK to choose options, PPV events,

and to tune to programs from the

program guide.

Use EXIT to exit out of your cable

converters menu and guide.

Use VOL+ (or VOL-) to raise (or lower)

the audio volume.

Use BRIGHT or DIM to control the

brightness level of your lights.

Use CH+ (or CH-) to select the next

higher (or lower) channel.

For DVD players, use these keys to skip

forward (or reverse) through chapters.

For amplifiers/receivers, use these keys

to select the next higher (or lower)

preset station.

Use ON or OFF to turn your Z-wave

compatible devices on or off.

Helix 5 Device.fm Page 6 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

Device Table

NOTE: Please refer to the table below when

performing the instructions in

“Programming Device Control” on page 9 or

“Setting Up a Combo Unit” on page 11.

Press MUTE once to turn the sound off

or on.

Press CANCEL to

Press LAST once to recall the last

channel.

Use to command your PVR/DVR

to instantly skip forward 7 seconds in

the program you are watching.

Use to command your PVR/DVR

cable box to instantly replay the last 7

seconds of a program you are watching.

Press LIVE TV to command your PVR/

DVR cable box to return to watching live

TV.

In all modes except SAT, use REW, PLAY,

FFWD, STOP, and PAUSE to control a

VCR, DVD player, or a PVR (after

selecting a desired device). To record in

the VCR mode, press REC twice.

In the SAT mode, use these keys to

control the DVR/PVR functions of the

set-top box.

Use the keypad numbers (1-9, and 0) to

directly tune channels (e.g., 09).

For amplifiers/receivers, use the keypad

numbers to select inputs 1 through 10.

Use TV/VID to select an input source.

Use ADD, REMOVE, DELETE, or SCENE to

control your Z-wave compatible devices.

Key Function

Helix 5 Device.fm Page 7 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

After programming, the Helix Z-wave 5-Device Remote

Control with Learning will be able to control the

following types of devices:

INSTALLING BATTERIES

1. On the back of the remote control, push the

tab and lift off the battery cover.

2. Locate the four (4) enclosed AAA batteries.

Match the + and - marks with those in the

battery case, then insert them.

Device Key Controls these types of devices

Audio Amplifier, Tuner, Receiver, CD

Player, Home Automation, or

Miscellaneous Audio

Tele v ision

DVD Player, VCR, PVR

Satellite Receiver, Cable Box

(Converter), or Video Accessory

Dedicated to Z-Wave controls

Helix 5 Device.fm Page 8 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

3. Align the covers keys with the cases holes and

press the cover back into place. The tab should

click when the cover is locked.

NOTE: When batteries need replacement, the remote

control will cease to operate. Replace the

batteries and the unit will be restored to its

full functionality, complete with your favorite

settings.

PROGRAMMING DEVICE CONTROL

The Helix Z-wave 5-Device Remote Control with

Learning is preprogrammed to operate an RCA satellite

receiver, TV, DVD player, and VCR, and a Pioneer audio

receiver. It can also control Z-wave compatible devices,

such as your home lighting system. To control devices

other than the default brands, perform the following

steps; otherwise skip this section.

NOTES: For control of a Combo device (for example, a

TV/VCR combo), skip this section and per-

form the instructions on “Setting Up a Combo

Unit” on page 11. Also refer to “Device Table”

on page 7 to find out which devices can be

programmed onto each device key.

If you have another brand of cable converter

or a satellite receiver you would like to control,

you’ll need to unlock the cable ID Lock before

changing the converter code (see “Program-

ming ID Lock” on page 19).

1. Turn on a device and, if applicable, insert

video media, (e.g., cassette or disc).

NOTE: Please read steps 2 through 4 completely

before proceeding. Highlight or write down

the codes and device you wish to program

before moving on to step 2.

3. Use the “Manufacturer’s Codes” starting on

page 34) to locate the type of device and

brand name and then enter the first four-digit

code for your device. If performed correctly,

the selected mode key will blink twice.

4. Test the remote control by pressing any mode

key (e.g., TV). If the batteries are inserted

correctly, the LED (red light) will blink once.

2. On the remote control, press a device key once

(i.e., TV, DVD/VCR, SAT, or AUX); it will blink

once. Then press and hold SETUP until the

selected mode key blinks twice.

Helix 5 Device.fm Page 9 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

NOTE: If the selected mode key emits a long blink,

the entry is invalid. Repeat steps 2 through 3

and try entering the same code again.

NOTE: If the device does not have a PWR key, press

the(Play) key.

5. Repeat steps 1 through 4 for each device you

want the remote control to operate. For future

reference, write down each working device

code in the boxes on the following page.

VCR Code

Device Type:___________________

DVD Code

Device Type:___________________

AMP Code

Device Type:___________________

SAT Code

Device Type:___________________

TV Code

Device Type:___________________

4. Aim the remote control at the device and

press PWR once. The device should turn off. If

it does not, repeat steps 2 through 3, trying

each code for your brand until you find one

that works. If it still does not respond, try

searching for the code (see “Searching for

Your Code” on page 12).

Helix 5 Device.fm Page 10 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

SETTING UP A COMBO UNIT

If you own a combo unit such as a TV/VCR Combo or a

TV/DVD Combo, you need to follow special steps to set

it up. Perform the following instructions to control

combo device:

1. For a TV/VCR Combo, turn on your TV/VCR

Combo and insert a video cassette. (For a TV/

DVD Combo, insert a DVD).

3. Use the “Manufacturer’s Codes” starting on

page 34 to locate the brand name and enter

the first four-digit code for your combo device

(for example, TV/VCR). If you perform this

procedure correctly, the DVD/VCR key will

blink twice.

NOTE: If the DVD/VCR key did not blink twice after

entering the codes last digit, repeat steps 2

through 3 and try entering the same code

again.

If you’ve located a setup code that works for

your combo device (for example, a TV/VCR

Combo) and a separate TV code is also listed,

you’ll need to program this code into the

remote control to access volume control (see

“Programming Device Control” starting on

page 9).

5. For future reference, write down each working

device code in the boxes below:

TV/VCR or TV/DVD Code

TV Code (if used)

2. On the remote control, press DVD/VCR once; it

will blink once. Then press and hold SETUP

until the DVD/VCR key blinks twice.

4. Aim the remote control at your combo device

(for example, TV/VCR Combo) and press

PWR once. The device should turn off. If it

does not respond, repeat steps 2 through 3,

trying each code listed for your brand until

you find one that works. If it still does not

respond, try searching for the code

(“Searching for Your Code” starting on

page 12).

Helix 5 Device.fm Page 11 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

SEARCHING FOR YOUR CODE

If your home entertainment device does not respond to

the Helix Z-wave 5-Device Remote Control with

Learning after trying all of the codes listed for your

brand, or if your brand is not listed at all, try searching

for your code.

For example, to search for a code for your TV:

1. Turn on your TV.

7. To search for the codes of your other devices,

repeat steps 1 through 6, but substitute the

appropriate key (e.g., VCR, DVD, AMP, or SAT)

for the device you are searching for.

2. On the remote control, press TV once; it will

blink once. Then press and hold SETUP until

the TV key blinks twice.

3. Enter 9 9 1. The TV key will blink twice.

4. Aim the remote control at the TV and press

PWR once.

5. Press and release the CH+ key continuously,

then stop when the TV turns off.

NOTE: In the search mode, the remote control will

send IR codes from its library to the selected

device, starting with the most popular code

first.

6. Press PWR. The TV should turn on, then press

SETUP to lock in the code.

NOTE: If the TV does not turn on during step 6, then

slowly press and release CH- to go back

through the codes, then press SETUP when the

TV turns on.

Helix 5 Device.fm Page 12 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

CHECKING THE CODES

If you have set up the Helix Z-wave 5-Device Remote

Control with Learning by searching for your device code

(on the previous page), you may need to find out which

four-digit code is operating your equipment.

or example, to find out which code is operating your TV

5. To check for other device codes, repeat steps 1

through 4, but substitute the appropriate key

(e.g., VCR, DVD, AMP, or SAT) for the device

you are checking. Write down the codes in the

appropriate boxes on page 10.

USING LEARNING

The Helix Z-wave 5-Device Remote Control with

Learning includes a Learning feature so you can add

functions that are unique to your home entertainment

devices (e.g.,VCR T

racking Up or Down). However, there

are some considerations

Learning Precautions

• Your original remote controls must be in working

order for learning to work properly.

• Learned keys are mode-specific, so each one can

store a unique function for each mode.

• Do not use the following keys for learning: Device

Keys, SETUP, Record (•), Tune-In Keys.

1. On the remote control, press TV once; it will

blink once. Then press and hold SETUP until

the TV key blinks twice.

2. Enter 9 9 0. The TV key will blink twice.

3. To view the code for the first digit, press 1

once. Count the number of times the TV key

blinks (e.g., 3 blinks = 3) and write down the

number in the leftmost TV Code box on

page 10.

NOTE: If a code digit is 0, the selected mode key will

not blink.

4. Repeat step 3 three more times for the

remaining digits. Use 2 for the second digit, 3

for the third digit, and 4 for the fourth digit.

Finish writing down the code in the TV Code

boxes on page 10.

Helix 5 Device.fm Page 13 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

• Learning capacity is approximately 16 to 25 keys,

depending on the code being learned.

• Certain device functions are not learnable including

multi-frequency types, some high frequency ones,

and other unusual formats.

• For optimum learning, avoid high levels of ambient

light such as natural sunlight or energy-efficient

fluorescent lights.

NOTE: Please have your original remote controls

handy before programming learning.

Programming a Learned Key

NOTE: If more than 15 seconds pass between key

presses, the remote exits programming.

3. Then press the key on your Helix Remote

Control that learns the new code.

4. Place the Helix Z-wave 5-Device Remote

Control with Learning head-to-head (about 2"

apart) from your original remote control. Also

locate the key (on your original remote

control) that you want the Helix Z-wave 5-

Device Remote Control with Learning to

learn.

5. On the original remote, press and hold the key

to be learned. The Helix Z-wave 5-Device

Remote Control with Learning’s LED will

blink rapidly, then turn off. Continue holding

1. Press and hold SETUP until the last-selected

mode key blinks twice, then press 9 7 5.

NOTE: If the LED displays one long flash instead,

either your batteries are low, or the Helix Z-

wave 5-Device Remote Control with Learning

has a memory fault.

2. Press a mode key once (i.e., TV, DVD/VCR, SAT,

or AUX) to assign a mode for learning.

Helix 5 Device.fm Page 14 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

the key on the original remote until the Helix

Z-wave 5-Device Remote Control with

Learning’s LED blinks twice.

NOTE: If the LED displays one long blink, a learning

error has occurred. Try repeating this step

again until a successful capture occurs. If the

function is still not captured, press and hold

SETUP to exit programming and review the

“Learning Precautions” on the previous page.

If needed, also see “Troubleshooting” on

page 31. After review, start programming

again at step 1.

Deleting a Single Learning Key

his process returns the key to its original programmin

for the mode you select. You can also delete learned

programming by teaching a different function to the key

(see “Programming a Learned Key” on page 14)

NOTE: If more than 15 seconds pass between key

presses, the remote exits programming.

3. Press the key containing the learned function

to be deleted twice. The remote will blink

twice.

6. Repeat steps 2 through 5 for another mode

and/or key or press and hold SETUP to exit

programming.

1. Press and hold SETUP until the last-selected

mode key blinks twice, then press 9 7 6.

2. Press a mode key once (i.e., TV, DVD/VCR, SAT,

or AUX).

4. Repeat steps 2 through 3 for another key or

press and hold SETUP to exit programming.

Helix 5 Device.fm Page 15 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

Deleting All Learned Keys in a Specific Mode

NOTE: If more than 15 seconds pass between key

presses, the remote exits programming.

PROGRAMMING CHANNEL CONTROL LOCK

By default, the remote control’s channel-control

capabilities are locked to the cable converter. The

affected keys* are 1 through 0, CH+, CH-, and LAST. This

will guarantee that you do not inadvertently change a

channel on your TV or VCR. However, you can de-

activate this feature to allow full access to these keys in

the TV and VCR modes.

*NOTE: This feature does not affect the AMP mode.

Unlocking Channel Control

Now the remote control will provide TV and VCR

channel-control capabilities while in the TV or VCR

mode.

1. Press and hold SETUP until the last-selected

mode key blinks twice, then press 9 7 6.

2. Press a mode key twice (i.e., TV, DVD/VCR, SAT,

or AUX) to clear all the learned keys for that

mode. The LED blinks twice.

3. Repeat step 2 for another mode or press and

hold SETUP to exit programming.

1. On the remote control, press SAT once; it will

blink once. Press and hold SETUP until the SAT

key blinks twice.

2. Enter 9 7 3. The SAT key will blink twice.

3. Press CH- once. The SATSAT key will blink four

times.

Helix 5 Device.fm Page 16 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

Locking Channel Control to SAT

Now, regardless of what mode you select (except AMP),

the channel keys will only change channels on your cable

converter.

CHANGING VOLUME LOCK

Volume Lock allows you to control the volume through

the device identified as having your primary speaker(s),

regardless of which mode you are using. On the Helix Z-

wave 5-Device Remote Control with Learning, Global

Volume Lock is set to TV, so you can control TV volume

while in the VCR, DVD, TV or SAT mode. You can perform

Individual Volume Unlock on a selected device to set its

volume control for independent operation.

NOTE: The audio mode’s (AMP) volume controls are

active regardless of Volume Lock settings.

However, if you lock the volume controls to

the AMP mode, you will have control of the

audio device’s volume in all other modes (i.e.,

VCR, DVD, TV, and SAT). This can be an advan-

tage if, for example, you always listen to home

entertainment devices through your receiver’s

speakers.

Unlocking Volume Control for a Single Device

(Individual Volume Unlock)

1. On the remote control, press SAT once; it will

blink once. Press and hold SETUP until the SAT

key blinks twice.

2. Enter 9 7 3.The SAT key will blink twice.

3. Press CH+ once. The SAT key will blink twice.

1. Assuming Global Volume Lock is active, select

a mode on the remote control that you want to

unlock (e.g., SAT) and press it once. Next,

press and hold SETUP until the device key

blinks twice.

2. Enter 9 9 3. The last-selected device key will

blink twice.

Helix 5 Device.fm Page 17 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

4. Repeat steps 1 through 3 for each device you

want volume to be unlocked.

Now, after you select a device that has volume unlocked

(e.g., SAT), pressing VOL+, VOL-,or MUTE, will control

only that device’s volume.

Unlocking All Volume Control (Global Volume Unlock)

NOTE: Performing these instructions will set inde-

pendent volume control for all programmed

devices.

Locking Volume Control To One Mode (Global

Volume Lock)

NOTE: The audio mode’s volume controls are active

regardless of Volume Lock settings. However,

if you lock the volume controls to the AMP

mode, you will control the audio device’s vol-

ume in all other modes (i.e., VCR, DVD, TV, or

CBL). This can be an advantage if, for exam-

ple, you always listen to home entertainment

devices through your receiver’s speakers.

3. Press VOL- once. The last-selected device key

will blink four times.

1. On the remote control, press and hold SETUP

until the last-selected device key blinks twice.

2. Enter 9 9 3. The last-selected device key will

blink twice.

3. Press VOL+ once. The last-selected device key

will blink four times.

1. On the remote control, press and hold SETUP

until the last-selected device key blinks twice.

2. Enter 9 9 3. The last-selected device key will

blink twice.

3. Select a mode (e.g., TV or AMP) which you

want to use to control the volume. The

selected device key will blink twice.

Helix 5 Device.fm Page 18 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

Now, when you press VOL+, VOL-,or MUTE, the volume of

the selected device (e.g., TV) is controlled regardless of

mode.

PROGRAMMING ID LOCK

The Helix Z-wave 5-Device Remote Control with

Learning is locked at the factory to operate your

provider’s set top box. However, if you have another

brand or model of cable converter or satellite service

that you would like to control, then you’ll need to

perform the following steps to unlock the ID Lock, enter

a new manufacturer’s code, and lock the ID Lock again.

1. Turn on the cable converter.

4. Perform the instructions under

“Programming Device Control” on page 9 to

program device control for the desired cable

converter or satellite receiver.

When you are done, perform steps 5 and 6 on

this page to again lock the cable ID Lock.

PROGRAMMING A MACRO KEY

The Helix Z-wave 5-Device Remote Control with

Learning includes a macro key feature. Macro keys allow

you to set up key macros to activate certain keys in a

specific order. For example, you can set up a key macro

to change the channels on your TV, raise or lower the

volume, and start recording on your VCR, all with the

touch of one key. If you want to change the macros

stored in a previously-programmed macro key, you’ll

2. On the remote control, press SAT once; it will

blink once. Then press and hold SETUP until

the SAT key blinks twice.

3. Enter 9 8 2. The SAT key will blink four

times, indicating ID Lock is unlocked.

5. On the remote control, press SAT once; it will

blink once. Then press and hold SETUP until

the SAT key blinks twice.

6. Enter 9 8 2. The SAT key will blink twice,

indicating ID Lock is again locked.

Helix 5 Device.fm Page 19 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

need to clear the key first (see “Clearing a Macro Key” on

page 20).

Programming a Macro Key

3. Select a macro key (for example, 1) and press

it once.

NOTE: You can program up to 15 key presses into one

macro.

6. To add another macro, repeat steps 1 through

5, substituting the new key sequence to be

added in step 4.

NOTE: Programming more than five macros on the

same macro key overwrites previous settings.

Clearing a Macro Key

3. Press the macro key you want to clear once.

This macro key is now clear and ready for

reprogramming (see “Programming a Macro Key” on

page 20). If desired, repeat these to clear another Tune-

In key.

1. On the remote control, press and hold SETUP

until it blinks twice.

2. Enter 9 9 5. The SETUP key blinks twice.

4. Press the key sequence you want to program

into the macro. For example, to turn on your

TV and raise its volume, press TV followed by

VOL+.

5. Press and hold SETUP until it blinks twice.

1. On the remote control, press and hold SETUP

until it blinks twice.

2. Enter 9 9 5. The SETUP key blinks twice.

4. Press and hold SETUP until it blinks twice.

Helix 5 Device.fm Page 20 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

USING THE MASTER POWER KEY

The Helix Z-wave 5-Device Remote Control with

Learning has a unique feature that allows you to

sequentially turn up to five of your home entertainment

devices on or off with a single key press.

NOTE: MASTER POWER (PWR) only works in the SAT

mode. If it is not programmed, only the cable

converter will turn on or off. In any other

mode, pressing MASTER POWER (PWR) once

will turn the selected device on or off.

Programming the Master Power Key

5. Repeat step 4 up to four more times to add the

second, third, fourth, and fifth device, as

desired.

6. To save the settings and exit the program:

Using the Master Power Key

You will see the devices turn on or off according to the

programmed sequence.

1. On the remote control, press and hold SETUP

until the last-selected device key blinks twice.

2. Enter 9 9 5. The last-selected device key

blinks twice.

3. Press PWR once.

4. For the first device you want in the power on

sequence, press a device key (e.g., SAT) once.

Then press PWR once. For the second device

in the power sequence, press its key once (e.g,

TV). Then press PWR.

a. Press SAT once.

b. Press and hold SETUP until the SAT key blinks

twice.

1. After programming, point the remote control

at the devices. Press SAT once.

Press

PWR

once to sequentially turn the

programmed home entertainment devices on

or off.

Helix 5 Device.fm Page 21 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

Clearing the Master Power Key

RE-ASSIGNING DEVICE KEYS

The Helix Z-wave 5-Device Remote Control with

Learning can be set up to control a second device of an

already-assigned type. For example, to have the unit

control a TV, a Cable Converter, and two audio devices

(for example, two audio receivers), re-assign the unused

DVD/VCR key to operate the second audio device as

follows:

NOTE: DVD/VCR is preset at the factory to control an

RCA DVD. Performing the steps below will

overwrite those settings.

The DVD/VCR key is now ready to be programmed for

your second audio device. See “Programming Device

Control” on page 9. To re-assign other device keys,

repeat these and substitute the key sequence using the

following chart:

1. On the remote control, press and hold SETUP

until the last-selected device key blinks twice.

2. Enter 9 9 5. The last-selected device key

blinks twice.

3. Press and release PWR.

4. Press and hold SETUP until the SAT key blinks

twice.

1. On the remote control, press DVD/VCR once; it

will blink once. Then press and hold SETUP

until the DVD/VCR key blinks twice.

2. Enter 9 9 2. The DVD/VCR key will blink

twice.

3. Press AMP once, then press DVD/VCR once.

The DVD/VCR key will blink twice.

Helix 5 Device.fm Page 22 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

NOTE: Only one device can be assigned to an unused

device key at a time.

To re-assign another unused device key, substitute it for

the DVD/VCR key above and then perform the sequence.

For example, to re-assign an unused AMP key as a

second DVD key, perform

AMPÆSETUPÆ9Æ9Æ2ÆDVDÆAMP.

When a re-assignment is done, the selected device key

(e.g., AMP) will blink twice to confirm your choice. At

that time, you will need to program device control (see

“Programming Device Control” on page 9).

ADDING A NODE TO YOUR Z-WAVE NETWORK

The Helix Z-wave 5-Device Remote Control with

Learning allows you to control lights around your home.

In order to control the lights, they must be Z-wave

compatible and you must first add them to your home

network.

Adding a Node to the Network

To add a node to your home network, perform the

following steps:

NOTE: If the Home red LED emits one long, steady

blink, you have pressed an invalid key or the

node has not been successfully added the

To Re-Assign Perform Key Sequence

DVD/VCR as

2nd AMP key

DVD/

VCRÆSETUPÆ9Æ9Æ2ÆAMPÆDVD

/VCR

DVD/VCR as

2nd TV key

DVD/

VCRÆSETUPÆ9Æ9Æ2ÆTVÆDVD/

VCR

DVD/VCR as

2nd SAT key

DVD/

VCRÆSETUPÆ9Æ9Æ2ÆSATÆDVD/

VCR

DVD/VCR

back to VCR

DVD/VCRÆSETUPÆ9Æ9Æ2ÆDVD/

VCRÆDVD/VCR

1. Press HOME once.

2. Press and release ADD twice. The red LED

blinks rapidly.

3. Press the button on the node so that it sends

its information to the remote and receives

information from the remote.

4. The HOME LED blinks green twice.

Helix 5 Device.fm Page 23 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

node to your home network. Please make sure

the remote is close to the node and try again.

Deleting a Node from the Network

To remove a node from your home network, you must

delete it from the network. To delete the node from your

network, perform the following steps:

NOTE: If the Home red LED emits one long, steady

blink, you have pressed an invalid key or the

node has not been successfully added the

node to your home network. Please make sure

the remote is close to the node and try again.

SETTING UP SCENES

A scene is a single node or group of nodes that can be

preset to turn to a previously specified setting

(brightness level). You can set up a maximum of 20

scenes, containing up to 64 nodes per scene.

Adding a Node to a Scene

NOTE: If the red LED emits one long, steady blink,

you have pressed an invalid key or the node

has not been successfully added the node to

your home network. Please make sure the

remote is close to the node and try again.

1. Press HOME once.

2. Press and release DEL twice. The red LED

blinks rapidly.

3. Press the button on the node so that it sends

its information to the remote and receives

information from the remote.

4. The HOME LED blinks green twice.

1. Press HOME once.

2. Press ADD once.

3. Press SCENE once.

4. Press a digit (1-9) for the scene you wish to

add the node to. The red LED blinks rapidly.

5. Press the button on the node so that it sends

its information to the remote and receives

information from the remote.

6. The green LED blinks twice, then the red LED

blinks rapidly. Adjust the brightness on the

node within 30 seconds.

Helix 5 Device.fm Page 24 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

Removing a Node from a Scene

NOTE: If the red LED emits one long, steady blink, you

have pressed an invalid key or the node has not

been successfully removed from the scene.

Deleting a Scene

NOTE: If the red LED emits one long, steady blink, you

have pressed an invalid key or the scene has not

been successfully deleted.

CONTROLLING SCENES

To control a scene, perform the following steps:

NOTE: If the red LED emits one long, steady blink, the

remote has not successfully communicated with the

node.

Turning All Nodes On or Off

1. Press HOME once.

2. Press REMOVE once.

3. Press SCENE once.

4. Press a digit (1-9) for the node location you

wish to remove. The red LED blinks rapidly.

5. Press the button on the node so that it sends

its information to the remote and receives

information from the remote.

6. The green LED blinks twice, then the red LED

blinks rapidly.

1. Press HOME once.

2. Press DELETE once.

3. Press SCENE once.

4. Press a digit (1-9) for the scene you wish to

remove.

5. Press the button on the node so that it sends

its information to the remote and receives

information from the remote.

6. The green LED blinks twice. The scene has

been removed successfully.

1. Press HOME once.

2. Press the digit key for the scene you wish to

control (1-9).

3. Press the ON, OFF, DIM, or BRIGHT key. The

green LED blinks once.

If ON or OFF is pressed, all nodes associated

to the scene turn on or off. If DIM or BRIGHT

is pressed, all nodes associated with a scene

dim or brighten with each key press.

Helix 5 Device.fm Page 25 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

To turn all nodes either on or off, perform the following

steps:

NOTE: If the red LED emits one long, steady blink, you

have pressed an invalid key or the All-On/All-Off

command was not successful. Repeat the steps

above to try again.

Adding Nodes to All Control

NOTE: If the red LED emits one long, steady blink, the

node has not been successfully added to the group.

Deleting Nodes from All Control

NOTE: If the red LED emits one long, steady blink,

the node has not been successfully added to

the group.

TRANSFERRING NODE AND NETWORK

INFORMATION TO A SECONDARY REMOTE

You can add a secondary remote to your network, and

transfer your primary remote’s node and network

information to it. To transfer node and network

information to a secondary remote, perform the

following steps:

1. Place the two remotes near each other.

2. Press HOME.

1. Press HOME once.

2. Press ALL once.

3. Press either ON to turn the nodes on, or OFF to

turn the nodes off. Any ON or OFF can be

pressed. The green LED blinks once.

1. Press HOME once.

1. Press ADD once.

2. Press ALL once. The red LED blinks rapidly.

3. Press the button on the node so that it sends

its information to the remote and receives

information from the remote.

4. The green LED blinks twice. The node has

been successfully added.

1. Press HOME once.

1. Press REMOVE once.

2. Press ALL once. The red LED blinks rapidly.

3. Press the button on the node so that it sends

its information to the remote and receives

information from the remote.

4. The green LED blinks twice. The node has

been successfully deleted.

Helix 5 Device.fm Page 26 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

3. Press and hold SETUP until the red LED blinks

twice.

4. Enter 9 6 6 on the numeric keypad. The red

LED blinks twice.

5. Press CH+. The red LED blinks rapidly.

6. Put the target (secondary) remote into

programming mode so that it sends its

information to the primary remote, as well as

receives information from the remote. The

remote then transfers the network and node

information to the new secondary remote.

Refer to the user manual for the secondary

remote for more information.

7. The green LED blinks twice. You have

successfully transferred the information.

NOTE: If the red LED emits one long, steady blink,

the information has not been successfully

transferred.

8. Add nodes, groups, and scenes to the new

secondary remote as needed.

TRANSFERRING NETWORK INFORMATION TO A

SECONDARY REMOTE

You can add a secondary remote to your network, and

transfer your primary remote’s network information to

it. To transfer network information to a secondary

remote, perform the following steps:

1. Place the two remotes near each other.

2. Press HOME.

3. Press and hold SETUP until the red LED blinks

twice.

4. Enter 9 6 6 on the numeric keypad. The red

LED blinks twice.

5. Press CH-. The red LED blinks rapidly.

6. Put the target (secondary) remote into

programming mode so that it sends its

information to the primary remote, as well as

receives information from the remote. The

remote then transfers the network and node

information to the new secondary remote.

Refer to the user manual for the secondary

remote for more information.

7. The green LED blinks twice. You have

successfully transferred the information.

NOTE: If the red LED emits one long, steady blink, the

information has not been successfully transferred.

8. Add nodes, groups, and scenes to the new

secondary remote as needed.

Helix 5 Device.fm Page 27 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

PRIMARY CONTROLLER SHIFT

You can transfer all of your remote’s information to

another remote, so it becomes the new primary remote.

You can do this in two ways: either transferring all

information, or just transferring network information.

Transferring All Network and Remote Information

1. Place the two remotes near each other.

2. Press HOME.

3. Press and hold SETUP until the red LED blinks

twice.

4. Enter 9 6 8 on the numeric keypad. The red

LED blinks twice.

5. Press CH+. The red LED blinks rapidly.

6. Put the target (secondary) remote into

programming mode so that it sends its

information to the primary remote, as well as

receives information from the remote. The

remote then transfers the network and node

information to the new secondary remote.

Refer to the user manual for the secondary

remote for more information.

7. The green LED blinks twice. You have

successfully transferred the information.

NOTE: If the red LED emits one long, steady blink, the

information has not been successfully transferred.

8. Add nodes, groups, and scenes to the new primary

remote as needed.

Transferring Only Network Information

1. Place the two remotes near each other.

2. Press HOME.

3. Press and hold SETUP until the red LED blinks

twice.

4. Enter 9 6 6 on the numeric keypad. The red

LED blinks twice.

5. Press CH-. The red LED blinks rapidly.

6. Put the target (secondary) remote into

programming mode so that it sends its

information to the primary remote, as well as

receives information from the remote. The

remote then transfers the network and node

information to the new secondary remote.

Refer to the user manual for the secondary

remote for more information.

7. The green LED blinks twice. You have

successfully transferred the information.

Helix 5 Device.fm Page 28 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

NOTE: If the red LED emits one long, steady blink,

the information has not been successfully

transferred.

8. Add nodes, groups, and scenes to the new

primary remote as needed.

CONTROLLER COPY RECEIPT

Controller Copy Receipt allows your controller to receive

information from another controller. This would then

allow the unit to become a new primary or secondary

controller.

Copying Information from Another Controller

1. Place the two remotes near each other.

2. Press HOME.

3. Press and hold SETUP until the red LED blinks

twice.

4. Enter 9 6 7 on the numeric keypad. The red

LED blinks twice.

5. Press CH-. The red LED blinks rapidly.

6. Put the target (secondary) remote into

programming mode so that it sends its

information to the primary remote, as well as

receives information from the remote. The

remote then transfers the network and node

information to the new secondary remote.

Refer to the user manual for the secondary

remote for more information.

7. The green LED blinks twice. You have

successfully transferred the information.

NOTE: If the red LED emits one long, steady blink,

the information has not been successfully

transferred.

8. Add nodes, groups, and scenes to the new

primary remote as needed.

NETWORK RESET

Network Reset clears all Node and Network features.

The remote resets to the default setting for the Z-wave

network and node information.

Resetting the Network

1. Press HOME.

2. Press and hold SETUP until the red LED blinks

twice.

3. Enter 9 6 9 on the numeric keypad. The red

LED blinks continuously.

Helix 5 Device.fm Page 29 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

4. The green LED blinks twice. The network has

been successfully reset.

NOTE: If the red LED emits one long, steady blink,

the network has not been successfully reset.

NETWORK UPDATE

Network Update allows your controller to update the

entire Z-wave network.

Updating the Network

1. Press HOME.

2. Press and hold SETUP until the red LED blinks

twice.

3. Enter 9 6 3 on the numeric keypad. The red

LED blinks continuously.

4. The green LED blinks twice. The network has

been successfully reset.

NOTE: If the red LED emits one long, steady blink, the

network has not been successfully updated.

NETWORK RECOVERY

Network Recovery allows your controller to recover

network information.

Recovering Network Information

1. Press HOME.

2. Press and hold SETUP until the red LED blinks

twice.

3. Enter 9 6 1 on the numeric keypad. The red

LED blinks continuously.

4. The green LED blinks twice. The network has

been successfully reset.

NOTE: If the red LED emits one long, steady blink,

the network has not been successfully

updated.

REMOVING A FAILED NODE FROM THE

NETWORK

You can remove a failed node from the network. If a

node fails in the network the controller’s LED emits a

long blink when trying to access that node.

If the nodes fails, make sure that the node is properly

plugged in. If the node still fails to respond, you can

remove the from the network. The failed node is

permanently removed from the network and scene. In

case, the node responds, then the node is not removed.

Helix 5 Device.fm Page 30 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

Removing a Failed Node

1. Press and hold SETUP until the red LED blinks

twice.

2. Press 9 7 2. The green LED blinks

continuously.

3. The node has been successfully removed from

the network.

NOTE: If the red LED emits one long, steady blink,

the network has not been successfully

updated.

CLEARING CUSTOM PROGRAMMING

The Helix Z-wave 5-Device Remote Control with

Learning contains a Custom Programming Reset

program. You can use it to remove all custom

programming, except your setup codes and reassigned

device keys.

IMPORTANT: Executing this program will erase all cus-

tom settings for Volume Lock, Learned Keys,

Tune-In Keys, and Channel Lock. However,

your device programming remains.

TROUBLESHOOTING

PROBLEM: Device key does not blink when you press a

key.

SOLUTION: Replace the batteries with two (2) new AA

batteries (see “Installing Batteries” on page 8).

PROBLEM: Device key blinks when you press a key, but

home entertainment device does not respond.

SOLUTION: Make sure you are aiming the remote control

at your home entertainment device and that you are

within 15 feet of the device you are trying to control.

PROBLEM: The remote control does not control home

entertainment devices or commands are not performing

properly.

SOLUTION: Try all listed codes for the device brand

being set up. Make sure all devices can be operated with

an infrared remote control.

1. On the remote control, press and hold SETUP

until the last-selected device key blinks twice.

2. Enter 9 8 0. The last-selected device key

blinks twice, pauses, and blinks twice again to

confirm that all custom programming is

cleared.

Helix 5 Device.fm Page 31 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

PROBLEM: TV/VCR Combo does not respond properly.

SOLUTION: Use the VCR codes for your brand. Some

combo units may require both a TV code and a VCR

code for full operation (see page 11).

PROBLEM: No volume on a second TV.

SOLUTION: Follow instructions under “Changing

Volume Lock” on page 17.

PROBLEM: PLAY and STOP keys do not work on a

Motorola DCT-2000 cable converter.

SOLUTION: Re-program the SAT key for cable code 0476

(see “Programming Device Control” on page 9).

PROBLEM: Tried Search Method and still could not find

a working code.

SOLUTION: Try the Search Method again after clearing

out the device key as follows:

a. Press and hold SETUP until device key blinks twice.

b. Enter 9 9 2.

c. Press and release the device key to be cleared twice.

PROBLEM: Remote control does not turn on Sony or

Sharp TV/VCR Combo.

SOLUTION: For power on, these products require

programming TV codes on the remote control. For Sony,

use TV code 0000 and VCR code 0032. For Sharp, use

TV code 0093 and VCR code 0048.

FCC NOTICE

This equipment has been tested and found to comply

with the limits for a class B digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful

interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy

and if not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications.

However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does

cause harmful interference to radio or television

reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit

different from that to which the receiver is

connected.

Helix 5 Device.fm Page 32 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

• Consult the dealer or an experienced radio/TV

technician for help.

This equipment has been verified to comply with the

limits for a class B computing device, pursuant to FCC

Rules. In order to maintain compliance with FCC

regulations, shielded cables must be used with this

equipment. Operation with non-approved equipment or

unshielded cables is likely to result in interference to

radio and TV reception. The user is cautioned that

changes and modifications made to the equipment

without the approval of manufacturer could void the

user’s authority to operate this equipment.

FCC ID: MG35300

ADDITIONAL INFORMATION

This product does not have any user-serviceable parts.

Opening the case, except for the battery cover, may cause

permanent damage to your Helix Z-wave 5-Device Remote

Control with Learning.

• For help via the Internet, visit us at:

www.urcsupport.com

publication may be reproduced, transmitted, transcribed,

stored in any retrieval system, or translated to any language, in

any form or by any means, electronic, mechanical, magnetic,

optical, manual, or otherwise, without prior written

permission of Universal Electronics Inc.

URC-5300 07/07

Helix 5 Device.fm Page 33 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

MANUFACTURER’S CODES

Setup Codes for Audio Amplifiers

Adcom 30577, 31100

Aiwa 30406

Bose 30674

Carver 30269

Denon 30160

Durabrand 31561

Elan 30647

GE 30078

Harman/Kardon 30892

JVC 30331

Left Coast 30892

Lenoxx 31561

Linn 30269

Luxman 30165

Magnavox 30269

Marantz 30892, 30321, 30269

McIntosh 30251

Nakamichi 30321

NEC 30264

Optimus 30395, 30823

Panasonic 30308, 30521

Parasound 30246

Philips 30892, 30269

Pioneer 30823

Polk Audio 30892, 30269

RCA 30823

Realistic 30395

Sansui 30321

Shure 30264

Sony 30689, 30220, 30815, 31126

Soundesign 30078, 30211

Technics 30308, 30521

Victor 30331

Wards 30078, 30211

Yamaha 30354, 30133, 30143

Helix 5 Device.fm Page 34 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

Setup Codes for Audio Receivers

ADC 30531

Aiwa 31405, 30158, 30189,

30121, 30405, 31243,

31388, 31641

Akai 31512

Alco 31390

Amphion Media Works 31563, 31615

AMW 31563, 31615

Anam 31609, 31074

Apex Digital 31257, 31430, 31774

Arcam 31120

Audiotronic 31189

Audiovox 31390, 31627

B & K 30701, 30820, 30840

BK 30702

Bose 31229, 30639, 31253,

31629, 31841, 31933

Brix 31602

Cambridge Soundworks 31370

Capetronic 30531

Carver 31189, 30189, 30042

Classic 31352

Coby 31263, 31389

Criterion 31420

Curtis Mathes 30080

Daewoo 31250

Dell 31383

Delphi 31414

Denon 31360, 30004, 31142

Fisher 30042, 31801

Garrard 30463

Gateway 31517

Glory Horse 31263

Go Video 31532

Harman/Kardon 30110, 30189, 30891,

31304, 31306

Hewlett Packard 31181

Hitachi 31273, 31801

Initial 31426

Insignia 31030

Helix 5 Device.fm Page 35 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

Integra 30135, 31298, 31320

JBL 30110, 31306

JVC 30074, 31263, 31374,

31495, 31811, 31871

Kenwood 31313, 31570, 31569,

30027, 31916, 31670,

31262, 31261, 31052,

31032, 30569, 30337,

30314, 30313, 30239,

30186, 30077, 30042

KLH 31390, 31412, 31428

Koss 31366, 31497

Lasonic 31798

Lenoxx 31437

LG 31293

Linn 30189

Liquid Video 31497

LXI 30181

Magnavox 31189, 31269, 30189,

30391, 30531, 31514

Marantz 31189, 31269, 30039,

30189, 31289

MCS 30039, 30346

Mitsubishi 31393

NAD 30320, 30845

Nakamichi 30097, 30876, 31555

Norcent 31389

Nova 31389

Onkyo 30135, 30380, 30842,

31298, 31320, 31531

Optimus 31023, 30042, 30080,

30181, 30186, 30531,

30670, 30738, 30801, 31074

Oritron 31366, 31497

Panasonic 31308, 31518, 30039,

30309, 30367, 31288,

31316, 31548, 31633,

31763, 31764

Philips 31189, 31269, 30189,

30391, 31120, 31266

Pioneer 31023, 30014, 30080,

30150, 30244, 30531,

30630, 31384

Polaroid 31508

Polk Audio 30189, 31289, 31414

Helix 5 Device.fm Page 36 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

Proscan 31254

Quasar 30039

RadioShack 31263

RCA 31023, 31609, 31254,

30054, 30080, 30346,

30530, 30531, 31074,

31154, 31390, 31511

Realistic 30181

Regent 31437

Rio 31383, 31869

Saba 31519

Samsung 31295, 31500

Sansui 30189, 30346

Sanyo 30801, 31251, 31469, 31801

Sharp 30186, 31286

Sharper Image 31263, 31556

Sherwood 30491, 30502, 31077,

31423, 31517, 31653, 31905

Shinsonic 31426

Sirius 31602, 31627, 31811, 31987

Sonic Blue 31383, 31532, 31869

Sony 31058, 31441, 31258,

31759, 31622, 30158,

30168, 31349, 31406,

31442, 31558, 31658,

31758, 31858, 31958

Soundesign 30670

Stereophonics 31023

Sunfire 31313, 30313, 30314, 31052

Teac 30463, 31074, 31390, 31528

Technics 31308, 31518, 30039, 30309

Thorens 31189

Toshiba 31788

Venturer 31390

Victor 30074

Wards 30158, 30189, 30014,

30054, 30080

XM 31406, 31414

Yamaha 30176, 30186, 31176,

31276, 31331, 31375, 31476

Zenith 30857, 31293

Helix 5 Device.fm Page 37 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

Setup Codes for Audio Accessories

Setup Codes for Cable Boxes/Converters

Accurian 31106

Aiwa 30159

Altec Lansing 31056, 31485

Apple 31115, 31644

Cambridge Soundworks 31530

Creative 30872

iDeck 31106

Marantz 31491

Monitor Audio 31106

Motorola 31464

NaviPod 31644

Netgear 31785

Omnifi 31605

Roku 31828

Russound 31302

Slim Devices 31844

Sony 30159

Yamaha 31809, 31810

ABC 00003, 00008

Americast 00899

Bell South 00899

Digeo 01187

Director 00476

General Instrument 00476, 00810, 00276, 00003

GoldStar 00144

Hamlin 00273

Jerrold 00476, 00810, 00276, 00003

Memorex 00000

Motorola 01376, 00476, 00810,

00276, 01187

Pace 01877, 00237, 00008

Panasonic 00000, 00107

Paragon 00000

Philips 01305, 00317

Pioneer 01877, 00877, 00144, 00533

Pulsar 00000

Quasar 00000

RCA 01256

Helix 5 Device.fm Page 38 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

Setup Codes for CD Players

Regal 00273

Runco 00000

Samsung 00144

Scientific Atlanta 01877, 00877, 00477, 00008

Sony 01006

Starcom 00003

Supercable 00276

Thomson 01256

Torx 00003

Toshiba 00000

Zenith 00000, 00525, 00899

Aiwa 30157

Burmester 30420

California Audio Labs 30029, 30303

Carver 30157, 30179

Denon 30873, 30003, 30034

DKK 30000

DMX Electronics 30157

Fisher 30179

Garrard 30420

Genexxa 30032

Harman/Kardon 30157, 30173

Hitachi 30032

Integra 30101

JVC 30072

Kenwood 30681, 30626, 30028,

30037, 30190

KLH 31318, 31372, 31373, 31711

Krell 30157

Linn 30157

Magnavox 30157

Marantz 30626, 30029, 30157

MCS 30029

Miro 30000

Mission 30157

MTC 30420

NSM 30157

Onkyo 30868, 30101

Helix 5 Device.fm Page 39 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

Setup Codes for DBS

Optimus 31063, 30000, 30032,

30037, 30087, 30145,

30179, 30420, 30468, 31075

Panasonic 30029, 30303, 30388, 30752

Parasound 30420

Philips 30626, 30157

Pioneer 31063, 31062, 30032,

31087, 30468

Polk Audio 30157

Proton 30157

QED 30157

Quad 30157

Quasar 30029

RadioShack 31075

RCA 31062, 30032, 30053,

30179, 30420, 30468

Realistic 30179, 30420

Rotel 30157, 30420

SAE 30157

Sansui 30157

Sanyo 30087, 30179

Sharp 30861, 30037

Sherwood 31067

Sonic Frontiers 30157

Sony 30490, 30000, 30100,

31364, 30185

Soundesign 30145

TAG McLaren 30157

Tascam 30420

Teac 30420

Technics 30029, 30303

Victor 30072

Wards 30157, 30053

Yamaha 30490, 30888, 30036, 31292

AlphaStar 00772

Coolsat 01806

DirecTV 01377, 00392

Dishpro 01505, 01005, 00775, 01775

Echostar 01505, 01005

Hitachi 00819

Helix 5 Device.fm Page 40 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

Setup Codes for DVD Players

HTS 00775, 01775

Hughes Network Systems 00749, 01749

JVC 00775, 01775

LG 01414

Magnavox 00724, 00722

Memorex 00724

Motorola 00869

Panasonic 00247, 00701

Philips 00724, 01076, 00722, 00099

RCA 00566, 00855, 00143, 01392

Samsung 01276, 01109

Sony 01639

Star Choice 00869

Toshiba 00749, 00790, 01285

Uniden 00724, 00722

Zenith 01856

Accurian 21072, 21416

Adcom 21094

Advent 21016

Aiwa 20641

Akai 20695, 20770, 20899, 21089

Alco 20790

Allegro 20869

Amphion Media Works 20872

AMW 20872

Apex Digital 20672, 20717, 20755,

20794, 20796, 20797,

20830, 21004, 21020,

21056, 21061, 21100

Arrgo 21023

Aspire Digital 21168, 21407

Audiovox 20790, 21071, 21072,

21121, 21122

Axion 21071, 21072

Bel Canto Design 21571

Blaupunkt 20717

Blue Parade 20571

Broksonic 20695, 20868

Cinea 20831

Helix 5 Device.fm Page 41 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

CineVision 20876, 20833, 20869

Citizen 20695, 21277

Coby 20778, 21086, 21107, 21177

Craig 20831

Curtis Mathes 21087

CyberHome 20816, 20874, 21023,

21024, 21117, 21129, 21502

Daewoo 20784, 20705, 20833,

20869, 21169, 21172,

21234, 21242

Denon 20490, 20634

Desay 21407

DigitalMax 21738

Disney 20675, 21270

Dual 21068, 21085

Durabrand 21127

DVD2000 20521

Emerson 20591, 20675, 20821, 21268

Enterprise 20591

ESA 20821, 21268

Fisher 20670

Funai 20675, 21268, 21334

Gateway 21073, 21077, 21158, 21194

GE 20522, 20815, 20717

Go Video 20744, 20715, 20741,

20783, 20833, 20869,

21044, 21075, 21099,

21158, 21304, 21730

Go Vision 21071, 21072

GoldStar 20741

Greenhill 20717

Harman/Kardon 20582, 20702

Hitachi 20573, 20664, 21247

Hiteker 20672

Humax 21588

iLo 21348

Initial 20717

Insignia 21268

Integra 20627

JBL 20702

Jensen 21016

Helix 5 Device.fm Page 42 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

JVC 20558, 20623, 20867,

21164, 21275, 21602, 21863

Kawasaki 20790

Kenwood 20490, 20534

KLH 20717, 20790, 21020, 21149

Koss 20651

Lasonic 20798

Lenoxx 21127

LG 20591, 20741, 20801, 20869

LiteOn 21058, 21158, 21416,

21440, 21738

Loewe 20511

Magnavox 20503, 20539, 20646,

20675, 20821, 21268, 21506

Malata 20782

Marantz 20539

McIntosh 21273

Memorex 20695, 20831, 21270

Microsoft 20522, 21708

Mintek 20839, 20717

Mitsubishi 21521, 20521

NAD 20741

Nakamichi 21222

NEC 20785

Nesa 20717

NexxTech 21402

Norcent 21003, 20872, 21107, 21265

Onkyo 20503, 20627, 20792

Oritron 20651

Panasonic 20490, 20632, 20703,

21362, 21462, 21490, 21762

Philips 20503, 20539, 20646,

20675, 20854, 21260,

21267, 21354

Pioneer 20525, 20571, 20631, 20632

Polaroid 21020, 21061, 21086

Polk Audio 20539

Portland 20770

Presidian 20675, 21072, 21738

Prima 21016

Proscan 20522

ProVision 20778

Helix 5 Device.fm Page 43 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

Setup Codes for DVD/PVR Combos

Qwestar 20651

RCA 20522, 20571, 20717,

20790, 20822, 21022,

21132, 21769

Rio 20869

Rotel 20623, 21178

Rowa 20823

Sampo 20698, 20752

Samsung 20490, 20573, 20199,

20820, 20899, 21044, 21075

Sansui 20695

Sanyo 20670, 20695, 20873

Sensory Science 21158

Sharp 20630, 20675, 20752, 21256

Sharper Image 21117

Sherwood 20633, 20770, 21043, 21077

Shinsonic 20533, 20839

Sonic Blue 20869, 21099

Sony 20533, 21533, 20864,

21033, 21070, 21431, 21892

Sova 21122

Superscan 20821

Sylvania 20675, 20821, 21268

Symphonic 20675, 20821

TAG McLaren 20894

Teac 20790

Technics 20490, 20703

Theta Digital 20571

Tivo 21503

Toshiba 20503, 20695, 21045,

21154, 21503, 21588, 21769

Tredex 20800

Urban Concepts 20503

US Logic 20839

Venturer 20790

Vizio 21064, 21226

Xbox 20522, 21708

Yamaha 20490, 20539, 20545

Zenith 20503, 20591, 20741, 20869

Zoece 21265

Helix 5 Device.fm Page 44 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

Controlled by the DVD

Controlled by the VCR

Go Video 21730

Humax 21588

Panasonic 20490

Pioneer 20631

RCA 20522

Sharp 21256

Sylvania 20675

Toshiba 21503, 21588

RCA 20880

Sylvania 20000

Toshiba 21008, 21996

Helix 5 Device.fm Page 45 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

Setup Codes for Home Automation

Setup Codes for Satellite Receivers

Accutek 31215

Amana 31716

Audio Access 30154

Bionaire 30846, 31215

Comfortex 30400

Da-Lite 30780

Frigidaire 31333, 31845

GE 30240

GoldStar 31537

Holmes 31215

Hunter Douglas 30433

Kenmore 31537

Lasko 30846

LG 31537

Lightolier 30184

LiteTouch 30084

Lutron 30597, 30318, 31239, 31597

One For All 30167

PCS 30184

RadioShack 30240

Royal Sovereign 31651

Russound 31232, 31233

Security System 30167

Sharper Image 30846

SmartLinc 30184

Somfy 30780

Universal X10 30167

Whirlpool 31332

Windmere 31215

X10 30167

AlphaStar 00772

Bell ExpressVu 00775, 01170

Chaparral 00216

Coolsat 01806

Crossdigital 01109

Helix 5 Device.fm Page 46 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

DirecTV 01377, 00392, 00566,

00639, 01639, 01142,

00247, 00749, 01749,

00724, 00819, 01856,

01076, 01108, 00099,

01109, 01392, 01414,

01442, 01443, 01444,

01609, 01640

Dish Network System 01505, 01005, 00775,

01170, 01775

Dishpro 01505, 01005, 00775, 01775

Echostar 01505, 01005, 00775,

01170, 01775

Expressvu 00775, 01775

GE 00566

General Instrument 00869

GOI 00775, 01775

Hisense 01535

Hitachi 00819, 01250

HTS 00775, 01775

Hughes Network Systems 01142, 00749, 01749,

01442, 01443, 01444

Humax 01790

iLo 01535

JVC 00775, 01170, 01775

LG 01226, 01414

Magnavox 00724, 00722

Memorex 00724

Mitsubishi 00749

Motorola 00869

Next Level 00869

Panasonic 00247, 00701

Pansat 01807

Paysat 00724

Philips 01142, 00749, 01749,

00724, 01076, 00722,

00099, 01442, 00856

Proscan 00392, 00566

Proton 01535

RadioShack 00869

RCA 00566, 00855, 00143, 01392

Samsung 01377, 01276, 01108,

01109, 01442, 01609

Sony 00639, 01639, 01640

Helix 5 Device.fm Page 47 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

Star Choice 00869

Tivo 01142, 01442, 01443, 01444

Toshiba 00749, 01749, 00790, 01285

UltimateTV 01392, 01640

Ultrasat 01806

Uniden 00724, 00722

US Digital 01535

USDTV 01535

Voom 00869

Zenith 01856, 00856

Helix 5 Device.fm Page 48 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

Setup Codes for DVR/PVR Systems

Setup Codes for TVs

ABS 21972

Alienware 21972

CyberPower 21972

Dell 21972

DirecTV 20739

Gateway 21972

Go Video 20614

Hewlett Packard 21972

Howard Computers 21972

HP 21972

Hughes Network Systems 20739

Humax 20739

Hush 21972

iBUYPOWER 21972

Linksys 21972

Media Center PC 21972

Microsoft 21972

Mind 21972

Niveus Media 21972

Northgate 21972

Panasonic 20614, 20616

Philips 20618, 20739

RCA 20880

ReplayTV 20614, 20616

Samsung 20739

Sonic Blue 20614, 20616

Sony 20636, 21972

Stack 9 21972

Systemax 21972

Tagar Systems 21972

Tivo 20618, 20636, 20739

Toshiba 21008, 21972, 21996

Touch 21972

Viewsonic 21972

Voodoo 21972

ZT Group 21972

A-Mark 10003

Helix 5 Device.fm Page 49 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

Abex 10032

Accurian 11803

Action 10873

Admiral 10093, 10463

Advent 10761, 10783, 10815,

10817, 10842, 11933

Adventura 10046

Aiko 10092

Akai 10812, 10702, 10030,

10672, 11207, 11675,

11676, 11903, 11935

Alaron 10179

Albatron 10700, 10843

Ambassador 10177

America Action 10180

Ampro 10751

Anam 10180

AOC 10030, 10003, 10052, 11365

Apex Digital 10748, 10879, 10765,

10767, 10890, 11217, 11943

Archer 10003

Astar 11531, 11548

Audiovox 10451, 10180, 10092,

10003, 10623, 10710,

10802, 10846, 10875,

11284, 11937, 11951, 11952

Aventura 10171

Axion 11937

Bell & Howell 10154, 10016

BenQ 11032, 11315

Bradford 10180

Broksonic 10236, 10463, 10003,

11911, 11929, 11935, 11938

Byd:sign 11309, 11311

Cadia 11283

Candle 10030, 10046, 10056

Carnivale 10030

Carver 10054

Celebrity 10000

Celera 10765

Champion 11362

Changhong 10765

Helix 5 Device.fm Page 50 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

Cinego 11986

Citizen 10060, 10030, 10092,

10039, 10046, 10056,

10280, 11928, 11935

Clarion 10180

Commercial Solutions 11447, 10047

Concerto 10056

Contec 10180

Craig 10180

Crosley 10054

Crown 10180, 10039

Curtis Mathes 10047, 10054, 10154,

10451, 10093, 10060,

10702, 10030, 10145,

10166, 11919, 11347,

11147, 10466, 10056,

10039, 10016

CXC 10180

CyberHome 10794

Cytron 11326

Daewoo 10451, 10092, 11661,

10039, 10623, 10661,

10672, 11928

Dell 11080, 11178, 11264, 11403

Denon 10145, 10511

Denstar 10628

Diamond Vision 11996, 11997

Dumont 10017

Durabrand 10463, 10180, 10178,

10171, 11034, 10003

Dwin 10720, 10774

Electroband 10000

Electrograph 11623, 11755

Electrohome 10463

Emerson 10154, 10236, 10463,

10180, 10178, 10171,

11963, 11944, 11929,

11928, 11911, 11394,

10623, 10280, 10179,

10177, 10039, 10038

Emprex 11422, 11546

Envision 10030, 10813, 11365

Epson 10833, 10840, 11290

ESA 10812, 10171, 11944, 11963

Helix 5 Device.fm Page 51 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

Fisher 10154

FlexVision 10710

Fujitsu 10179, 10683, 10809, 10853

Funai 10180, 10171, 10179,

11271, 11904, 11963

Futuretech 10180

Gateway 11001, 11002, 11003,

11004, 11755, 11756

GE 11447, 10047, 10051,

10451, 10178, 10021,

10027, 11347, 11917,

11919, 11922

Gibralter 10017, 10030

Go Video 10886

GoldStar 10178, 10030, 10032, 11926

Grunpy 10180, 10179

Haier 11034, 10768

Hallmark 10178

Hannspree 11348, 11351, 11352

Harley Davidson 10179, 11904

Harman/Kardon 10054

Harvard 10180

Havermy 10093

Helios 10865

Hello Kitty 10451

Hewlett Packard 11088, 11089, 11101,

11494, 11502, 11642

Hisense 10748

Hitachi 11145, 10145, 10016,

10032, 10038, 10056,

10797, 11904, 11960

HP 11088, 11089, 11101,

11494, 11502, 11642

Hyundai 10849, 11219, 11294

iLo 11286, 11603, 11990

Infinity 10054

Initial 11603, 11990

Insignia 10171, 11204, 11326,

11517, 11564, 11963, 12002

Inteq 10017

Janeil 10046

JBL 10054

JCB 10000

Helix 5 Device.fm Page 52 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

Jensen 10761, 10815, 10817,

11299, 11933

JVC 10053, 10731, 11253, 11923

Kaypani 10052

KDS 11498

KEC 10180

Kenwood 10030

KLH 10765, 10767, 11962

Kloss 10024, 10046

Konka 10628, 10632, 10638,

10703, 10707

Kost 11262, 11483

KTV 10180, 10030, 10039, 10280

LG 11265, 10178, 10700,

10823, 10829, 10856,

11178, 11325, 11423,

11758, 11993

Lloyd's 11904

Logik 10016

Luxman 10056

LXI 10047, 10054, 10154,

10156, 10178

MAG 11498

Magnasonic 11928

Magnavox 11454, 10054, 10030,

10706, 11990, 11963,

11944, 11931, 11904,

11525, 11365, 11254,

11198, 10802, 10386,

10187, 10179, 10096,

10024, 10020

Majestic 10016

Marantz 10054, 10030, 10704,

10854, 10855, 11154, 11398

Matsushita 10250, 10650

Maxent 10762, 11211, 11755

Megapower 10700

Megatron 10178, 10145, 10003

Memorex 10154, 10463, 10150,

10178, 10016, 10179,

11911, 11926

MGA 10150, 10178, 10030

Midland 10047, 10017, 10051,

10032, 10039

Helix 5 Device.fm Page 53 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

Mintek 11603, 11990

Minutz 10021

Mitsubishi 10093, 11250, 10150,

10178, 10836, 10868,

11550, 11917

Monivision 10700, 10843

Motorola 10093, 10835

Moxell 10835

MTC 10060, 10030, 10056

Multitech 10180

NAD 10156, 10178, 10056,

10866, 11156

NEC 10030, 10056, 10497,

10882, 11398, 11704

NetTV 10762, 11755

Nikko 10178, 10030, 10092

Norcent 10748, 10824, 11089,

11365, 11589, 11590, 11591

Norwood Micro 11286, 11296, 11303

Noshi 10018

NTC 10092

Olevia 11144, 11240, 11331, 11610

Olympus 11342

Onwa 10180

Optimus 10154, 10250, 10166, 10650

Optoma 10887

Optonica 10093

Orion 10236, 10463, 11463,

10179, 11911, 11929

Panasonic 10250, 10051, 10650,

11291, 11410, 11480,

11919, 11941, 11946, 11947

Penney 10047, 10156, 10051,

10060, 10178, 10030,

10003, 10018, 10021,

10027, 10032, 10039,

11347, 11919, 11926

Petters 11523

Philco 10054, 10030, 10020, 10096

Philips 11454, 10054, 10690,

11154, 11483, 11961

Pilot 10030, 10039

Pioneer 10166, 10038, 10679,

10866, 11260, 11398

Helix 5 Device.fm Page 54 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

Polaroid 10765, 10865, 11262,

11276, 11314, 11316,

11326, 11327, 11328,

11341, 11498, 11523,

11962, 11991, 11992

Portland 10092, 10039

Prima 10761, 10783, 10815,

10817, 11933

Princeton 10700, 10717

Prism 10051

Proscan 11447, 10047, 11347, 11922

Proton 10178, 10003, 10052, 10466

Protron 11320, 11323

Proview 10835, 11401, 11498

Pulsar 10017

Quasar 10250, 10051, 10650, 11919

RadioShack 10047, 10154, 10180,

10178, 10030, 10032,

10039, 10056, 11904

RCA 11447, 10047, 12002,

11958, 11953, 11948,

11922, 11919, 11917,

11547, 11347, 11247,

11147, 11047, 10679,

10090, 10038, 10018

Realistic 10154, 10180, 10178,

10030, 10032, 10039, 10056

Runco 10017, 10030, 10497,

10603, 11398

Sampo 10030, 10032, 10039,

10052, 10762, 11755

Samsung 10060, 10812, 10702,

10178, 10030, 10032,

10056, 10766, 10814,

11060, 11312, 11395,

11575, 11903, 11959

Samsux 10039

Sansui 10463, 11409, 11904,

11911, 11929, 11935

Sanyo 10154, 10088, 10146,

10799, 10893, 11142

Sceptre 10878, 11217, 11360, 11599

Scotch 10178

Scott 10236, 10180, 10178, 10179

Helix 5 Device.fm Page 55 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

Sears 10047, 10054, 10154,

10156, 10178, 10171,

10056, 10146, 10179,

11904, 11926

Sharp 10093, 10039, 10386,

10491, 10688, 10689,

10818, 10851, 11602,

11917, 11393

Sheng Chia 10093

Sherwood 11399

Signature 10016

Signet 11262

SIM2 Multimedia 11297

Simpson 10187

Sony 11100, 10000, 10834,

11317, 11685, 11904, 11925

Soundesign 10180, 10178, 10179

Sova 11320, 11952

Soyo 11520

Spectricon 10003

Spectroniq 11498

Squareview 10171

SSS 10180

Starlite 10180

Studio Experience 10843

Superscan 10093, 10864

Supre-Macy 10046

Supreme 10000

SVA 10748, 10587, 10768,

10865, 10870, 10871, 10872

Sylvania 10054, 10030, 10171,

10020, 10096, 11271,

11314, 11394, 11931,

11944, 11963

Symphonic 10180, 10171, 11904, 11944

Syntax 11144, 11240, 11331

Tandy 10093

Tatung 10003, 11101, 11285,

11286, 11287, 11288,

11361, 11756

Technics 10250, 10051

Technol Ace 10179

Techview 10847

Techwood 10051, 10003, 10056

Helix 5 Device.fm Page 56 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

Teknika 10054, 10180, 10150,

10060, 10092, 10016,

10039, 10056, 10179

Telefunken 10702, 10056

Thomas 11904

TMK 10178, 10056, 10177

TNCi 10017

Toshiba 10154, 11256, 10156,

11265, 10060, 11945,

11936, 11935, 11918,

11704, 11656, 11635,

11524, 11356, 11343,

11325, 11306, 11156,

10845, 10832, 10650, 11971

Totevision 10039

TVS 10463

Ultra 11323

Universal 10027

US Logic 11286, 11303

Vector Research 10030

Victor 10053

Vidikron 10054, 11398

Vidtech 10178

Viewsonic 10797, 10857, 10864,

10885, 11330, 11342,

11578, 11627, 11640, 11755

Viking 10046

Viore 11207

Visart 11336

Vizio 10864, 10885, 11499,

11756, 11758

Wards 10054, 10178, 10030,

10016, 10020, 10021,

10027, 10056, 10096,

10179, 10866, 11156

Waycon 10156

Westinghouse 10885, 10889, 10890,

11282, 11577

White Westinghouse 10463, 10623

Wyse 11365

Yamaha 10030, 10769, 10797,

10833, 10839

Zenith 10017, 10463, 11265,

10178, 10092, 10016,

11904, 11911, 11929

Helix 5 Device.fm Page 57 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

Setup Codes for TVs (DLP)

Setup Codes for TVs (LCD)

Zonda 10003

Hewlett Packard 11494

HP 11494

LG 11265

Magnavox 11525

Mitsubishi 11250

Optoma 10887

Panasonic 11291

RCA 11447

Samsung 10812, 11060, 11312

SVA 10872

Toshiba 11265, 11306

Vizio 11499

Accurian 11803

Action 10873

Akai 11675, 11676, 11935

AOC 11365

Apex Digital 10890, 11217

Astar 11531, 11548

Audiovox 10180, 10710, 10802,

10846, 10875, 11284,

11937, 11951, 11952

BenQ 11315

Byd:sign 11309, 11311

Cadia 11283

Citizen 11935

CyberHome 10794

Dell 11080, 11178, 11264

Emprex 11422, 11546

Envision 10813, 11365

FlexVision 10710

Funai 10171

Go Video 10886

Hannspree 11348, 11351

Hewlett Packard 11088, 11642

Helix 5 Device.fm Page 58 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

HP 11088, 11642

Hyundai 10849, 11219, 11294

iLo 11286, 11603, 11990

Initial 11603, 11990

Insignia 11204, 11517, 11564, 12002

Jensen 11299

Kost 11262

LG 10856, 11178, 11993

Magnavox 10802, 11198, 11365, 11990

Marantz 10855

Maxent 10762, 11211, 11755

Mintek 11603, 11990

Mitsubishi 11250

NetTV 10762

Norcent 11365, 11589, 11591

Norwood Micro 11286, 11296

Olevia 11144, 11240, 11331, 11610

Panasonic 10650, 11941

Petters 11523

Philips 11454, 11483

Polaroid 11262, 11276, 11316,

11341, 11498, 11523

Protron 11320, 11323

Proview 11401

RCA 10047, 11958

Sampo 10762, 11755

Samsung 10812, 10766, 10814,

11395, 11575

Sansui 11409

Sanyo 11142

Sceptre 10878, 11217, 11360, 11599

Sharp 10093, 10818, 11602

Sherwood 11399

Signet 11262

Sony 11685

Sova 11320

Soyo 11520

Superscan 10864

SVA 10587, 10870, 10871

Sylvania 10171, 11271, 11314, 11394

Symphonic 10171

Helix 5 Device.fm Page 59 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

Setup Codes for TVs (Plasma)

Syntax 11144, 11240, 11331

Tatung 11286

Techview 10847

Toshiba 10845, 11343, 11524,

11635, 11656

Ultra 11323

US Logic 11286

Vidikron 11398

Viewsonic 10857, 10864, 10885,

11330, 11578, 11627, 11640

Visart 11336

Vizio 10864, 10885, 11756, 11758

Westinghouse 10885, 10889, 10890,

11282, 11577

Wyse 11365

Zenith 11265

Akai 10812, 11207, 11675

Albatron 10843

BenQ 11032

Byd:sign 11311

Daewoo 10661

Dell 11264

Electrograph 11623, 11755

ESA 10812

Fujitsu 10683, 10809, 10853

Funai 11271

Gateway 11001, 11002, 11003,

11004, 11755, 11756

Helios 10865

Hewlett Packard 11089, 11502

Hitachi 10797

HP 11089, 11502

Insignia 11564

JVC 10731

LG 10178, 10829, 10856,

11423, 11758

Marantz 10704, 11398

Maxent 11755

Mitsubishi 10836

Helix 5 Device.fm Page 60 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

Monivision 10843

Motorola 10835

Moxell 10835

NEC 11398, 11704

NetTV 11755

Norcent 10824, 11089, 11590

Norwood Micro 11303

Panasonic 10250, 10650, 11480

Philips 10690

Pioneer 10679, 11260, 11398

Polaroid 10865, 11276, 11327, 11328

Proview 10835

Runco 11398

Sampo 11755

Samsung 10812, 11312

Sony 10000, 11317

Studio Experience 10843

SVA 10865

Sylvania 11271, 11394

Tatung 11101, 11285, 11287,

11288, 11756

Toshiba 10650, 11704

US Logic 11303

Viewsonic 10797, 11755

Viore 11207

Vizio 11756, 11758

Yamaha 10797

Zenith 10178

Helix 5 Device.fm Page 61 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

Setup Codes for TV/DVD Combos

Controlled by the TV

Controlled by the DVD

Accurian 11803

Advent 11933

Akai 11675, 11935

Apex Digital 11943

Audiovox 11937, 11951, 11952

Axion 11937

Broksonic 11935

Cinego 11986

Citizen 11935

Diamond Vision 11997

Emerson 11394, 11963

ESA 11963

Funai 11963

Hitachi 11960

iLo 11990

Initial 11990

Insignia 11963, 12002

Jensen 11933

KLH 11962

LG 11993

Magnavox 11963, 11990

Mintek 11990

Panasonic 11941

Philips 11961

Polaroid 11962, 11991

Prima 11933

RCA 11948, 11958, 12002

Samsung 11903

Sansui 11935

Sova 11952

Sylvania 11394, 11963

Toshiba 11635, 11935

Advent 21016

Akai 20695

Apex Digital 20830

Audiovox 21071, 21121, 21122

Helix 5 Device.fm Page 62 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

Axion 21071

Broksonic 20695

Citizen 20695

Emerson 20675, 21268

ESA 21268

Funai 21268

Go Vision 21071

Hitachi 21247

Insignia 21268

Jensen 21016

Magnavox 21268

Panasonic 21490

Philips 20854, 21260

Prima 21016

RCA 21022

Samsung 20899

Sansui 20695

Sova 21122

Sylvania 20675, 21268

Toshiba 20695

Helix 5 Device.fm Page 63 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

Setup Codes for TV/VCR Combos

Controlled by the TV

Controlled by the VCR

America Action 10180

Audiovox 10180

Broksonic 11911, 11929

Citizen 11928

Curtis Mathes 11919

Daewoo 11928

Emerson 10236, 11911, 11928, 11929

Funai 11904

GE 11917, 11919, 11922

GoldStar 11926

Harley Davidson 11904

Hitachi 11904

JVC 11923

Lloyd's 11904

Magnasonic 11928

Magnavox 11904, 11931

Memorex 11926

Mitsubishi 11917

Orion 11911, 11929

Panasonic 11919

Penney 11919, 11926

Quasar 11919

RadioShack 11904

RCA 11917, 11919, 11922

Samsung 11959

Sansui 11904, 11911, 11929

Sears 11904, 11926

Sony 11904, 11925

Sylvania 11931

Symphonic 11904

Thomas 11904

Toshiba 11918, 11936

Zenith 11904, 11911, 11929

America Action 20278

Audiovox 20278

Broksonic 20002, 20479, 21479

Helix 5 Device.fm Page 64 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

Citizen 21278

Colt 20072

Curtis Mathes 21035

Daewoo 21278

Emerson 20002, 20479, 20593,

21278, 21479

Funai 20000

GE 20240, 20807, 21035, 21060

GoldStar 21237

Harley Davidson 20000

Hitachi 20000

LG 21037

Lloyd's 20000

Magnasonic 20593, 21278

Magnavox 20000, 20593, 21781

Magnin 20240

Memorex 20162, 21037, 21162,

21237, 21262

MGA 20240

Mitsubishi 20807

Optimus 20162, 20593, 21162, 21262

Orion 20002, 20479, 21479

Panasonic 20162, 21035, 21162, 21262

Penney 20240, 21035, 21237

Quasar 20162, 21035, 21162

RadioShack 20000, 21037

RCA 20240, 20807, 21035, 21060

Samsung 21014

Sansui 20000, 20479, 21479

Sanyo 20240

Sears 20000, 21237

Sony 20000, 21232

Sylvania 21781

Symphonic 20000, 20593

Thomas 20000

Toshiba 20845, 21145

Zenith 20000, 20479, 21479

Helix 5 Device.fm Page 65 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

Setup Codes for VCRs

ABS 21972

Admiral 20048, 20209

Adventura 20000

Aiko 20278

Aiwa 20037, 20000, 20124

Alienware 21972

America Action 20278

American High 20035

Asha 20240

Audiovox 20037, 20278

Beaumark 20240

Bell & Howell 20104

Broksonic 20184, 20121, 20209,

20002, 20479, 21479

Calix 20037

Canon 20035

Carver 20081

CCE 20072, 20278

Citizen 20037, 20278, 21278

Colt 20072

Craig 20037, 20047, 20240, 20072

Curtis Mathes 20060, 20035, 20162, 21035

Cybernex 20240

CyberPower 21972

Daewoo 20045, 20278, 21278

Dell 21972

Denon 20042

DirecTV 20739

Durabrand 20039, 20038

Dynatech 20000

Electrohome 20037

Electrophonic 20037

Emerex 20032

Emerson 20037, 20184, 20000,

20121, 20043, 20209,

20002, 20278, 20479,

20593, 21278, 21479, 21593

Fisher 20047, 20104

Fuji 20035, 20033

Funai 20000, 20593, 21593

Helix 5 Device.fm Page 66 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

Garrard 20000

Gateway 21972

GE 20060, 20035, 20240,

20807, 21035, 21060

Go Video 20432, 20614

GoldStar 20037, 20038, 21237

Gradiente 20000

Harley Davidson 20000

Harman/Kardon 20081, 20038

Harwood 20072

Hewlett Packard 21972

HI-Q 20047

Hitachi 20000, 20042, 20089

Howard Computers 21972

HP 21972

Hughes Network Systems 20042, 20739

Humax 20739

Hush 21972

iBUYPOWER 21972

JVC 20067

KEC 20037, 20278

Kenwood 20067, 20038

KLH 20072

Kodak 20035, 20037

LG 21037

Linksys 21972

Lloyd's 20000

Logik 20072

LXI 20037

Magnasonic 20593, 21278

Magnavox 20035, 20039, 20081,

20000, 20149, 20563,

20593, 21593, 21781

Magnin 20240

Marantz 20035, 20081

Marta 20037

Matsushita 20035, 20162, 21162

Media Center PC 21972

MEI 20035

Helix 5 Device.fm Page 67 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

Memorex 20035, 20162, 20037,

20048, 20039, 20047,

20240, 20000, 20104,

20209, 20479, 21037,

21162, 21237, 21262

MGA 20240, 20043

MGN Technology 20240

Microsoft 21972

Mind 21972

Minolta 20042

Mitsubishi 20067, 20043, 20807

Motorola 20035, 20048

MTC 20240, 20000

Multitech 20000, 20072

NEC 20104, 20067, 20038

Nikko 20037

Niveus Media 21972

Noblex 20240

Northgate 21972

Olympus 20035

Optimus 21062, 20162, 20037,

20048, 20104, 20432,

20593, 21162, 21262

Orion 20184, 20209, 20002,

20479, 21479

Panasonic 21062, 20035, 20162,

20225, 20614, 20616,

21035, 21162, 21262

Penney 20035, 20037, 20240,

20042, 20038, 21035, 21237

Pentax 20042

Philco 20035

Philips 20035, 20081, 20618,

20739, 21081, 21181

Pilot 20037

Pioneer 20067

Polk Audio 20081

Presidian 21593

Profitronic 20240

Proscan 20060, 21060

Protec 20072

Pulsar 20039

Quasar 20035, 20162, 21035, 21162

Helix 5 Device.fm Page 68 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

RadioShack 20000, 21037

Radix 20037

Randex 20037

RCA 20060, 20240, 20042,

20149, 20807, 20880,

21035, 21060

Realistic 20035, 20037, 20048,

20047, 20000, 20104

ReplayTV 20614, 20616

Ricavision 21972

Runco 20039

Samsung 20240, 20045, 20739, 21014

Sanky 20048, 20039

Sansui 20000, 20067, 20209,

20479, 21479

Sanyo 20047, 20240, 20104

Scott 20184, 20045, 20121, 20043

Sears 20035, 20037, 20047,

20000, 20042, 20104, 21237

Sharp 20048, 20807, 20848

Shintom 20072

Shogun 20240

Singer 20072

Sonic Blue 20614, 20616

Sony 20035, 20032, 20033,

20000, 20636, 21032,

21232, 21972

Stack 9 21972

STS 20042

Sylvania 20035, 20081, 20000,

20043, 20593, 21593, 21781

Symphonic 20000, 20593, 21593

Systemax 21972

Tagar Systems 21972

Teac 20000

Technics 20035, 20162

Teknika 20035, 20037, 20000

Thomas 20000

Tivo 20618, 20636, 20739, 21996

TMK 20240

Toshiba 20045, 20043, 20845,

21008, 21145, 21972, 21996

Totevision 20037, 20240

Helix 5 Device.fm Page 69 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

Setup Codes for Video Accessories

Touch 21972

Unitech 20240

Vector 20045

Vector Research 20038

Video Concepts 20045

Videomagic 20037

Videosonic 20240

Viewsonic 21972

Villain 20000

Voodoo 21972

Wards 20060, 20035, 20048,

20047, 20081, 20240,

20000, 20042, 20072, 20149

White Westinghouse 20209, 20072

XR-1000 20035, 20000, 20072

Yamaha 20038

Zenith 20039, 20033, 20000,

20209, 20479, 21479

ZT Group 21972

ABS 01272

Accurian 01653

Alienware 01272

CyberPower 01272

D-Link 01554, 01731

Epson 01563

Escient 01151, 01370, 01371

Gateway 01272

Hewlett Packard 01272, 01267

Howard Computers 01272

HP 01272

Hush 01272

iBUYPOWER 01272

JVC 01384

LG 01415

Linksys 01272, 01365

Media Center PC 01272

Microsoft 01272

Mind 01272

Motorola 01363

Helix 5 Device.fm Page 70 Tuesday, June 5, 2007 5:24 PM

www.urcsupport.com

Niveus Media 01272

Northgate 01272

Panasonic 01120

Pioneer 01010

Ricavision 01272

Roku 01486

Samsung 01190, 01490

Sensory Science 01126

Sharp 01010

Sony 01272, 01324, 01364

Stack 9 01272

Sylvania 01563

Systemax 01272

Tagar Systems 01272

Toshiba 01272

Touch 01272

Viewsonic 01272, 01329

Vizio 01126

Voodoo 01272

ZT Group 01272

Helix 5 Device.fm Page 71 Tuesday, June 5, 2007 5:24 PM

URC-5300

Revision 1.0

Helix 5 Device.fm Page 72 Tuesday, June 5, 2007 5:24 PM

Universal Electronics 5300 (Helix) UEI Z-wave 5 Device Remote 2007 User Manual Part 1

Universal Electronics Inc (Helix) UEI Z-wave 5 Device Remote 2007 Users Manual Part 1

Contents

Users Manual Part 1

Navigation menu

Namespaces

Views

Navigation