VTech Telecommunications 80-5125-B01 900MHz/2.4GHz 30 Channel Analog Modulation Cordles User Manual Pt1 1yr Eng China 3ATT

Download:
Mirror Download [FCC.gov]
Document ID	163701
Application ID	pFmsVXWPsVM4/3dBLHBCbQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	21.69kB (271144 bits)
Date Submitted	2001-08-09 00:00:00
Date Available	2002-09-12 00:00:00
Creation Date	2001-07-18 10:26:23
Producing Software	Acrobat Distiller 3.01 for Power Macintosh
Document Lastmod	2001-07-18 10:30:13
Document Title	Pt1_1yr_Eng_China_3ATT
Document Creator	QuarkXPressª 4.1: LaserWriter 8 8.1.1

Pt1_1yr_Eng_China_3ATT
7/18/01
10:25 AM
Page 1
Part 1
IMPORTANT PRODUCT INFORMATION
Safety Information
This symbol is to alert you to important operating
or servicing instructions that may appear in this
user’s manual. Always follow basic safety precautions when
using this product to reduce the risk of injury, fire, or
electric shock.
1 Read and understand all instructions in the user’s
manual. Observe all markings on the product.
2 Avoid using a telephone during a thunderstorm.
There may be a slight chance of electric shock from
lightning.
3 Do not use a telephone in the vicinity of a gas leak.
If you suspect a gas leak, report it immediately, but use a
telephone away from the area where gas is leaking. If this
product is a cordless model, make sure the base is also
away from the area.
4 Do not use this product near water, or when you
are wet. For example, do not use it in a wet basement or
shower, or next to a swimming pool, bathtub, kitchen
sink, or laundry tub. Do not use liquids or aerosol sprays
for cleaning. If the product comes in contact with any
liquids, unplug any line or power cord immediately. Do
not plug the product back in until it has dried thoroughly.
5 Install this product in a protected location where no
one can trip over any line or power cords. Protect cords
from damage or abrasion.
6 If this product does not operate normally, read “In
Case of Difficulty” in the user’s manual. If you cannot
solve the problem, or if the product is damaged, refer to
the Limited Warranty. Do not open this product except
(Continued)
AT&T and the globe symbol are registered trademarks of AT&T Corp.
licensed to Advanced American Telephones.
Pt1_1yr_Eng_China_3ATT
7/18/01
10:25 AM
Page 2
as may be directed in your user’s manual. Opening the
product or reassembling it incorrectly may expose you
to hazardous voltages or other risks.
7 If this product has user-replaceable batteries,
replace batteries only as described in your user’s
manual. Do not burn or puncture batteries — they
contain caustic chemicals.
8 If this product has a three-prong (grounding) plug
or a polarized plug with one wide prong, it may not
fit in non-polarized outlets. Do not defeat the purpose of
these plugs. If they do not fit in your outlet, the outlet
should be replaced by an electrician.
CAUTION: Use only the power adapter provided
with this product. To obtain a replacement,
call 1 800 222–3111.
SAVE THESE INSTRUCTIONS
Especially About Cordless Telephones
Privacy: The same features that make a cordless phone
convenient create some limitations. Telephone calls are
transmitted between the base and the handset by radio
waves, so there is a possibility that your cordless phone
conversations could be intercepted by radio receiving
equipment within range of the cordless handset. For this
reason, you should not think of cordless phone
conversations as being as private as those on corded
phones.
Electrical Power: The base unit of this cordless telephone
must be connected to a working electrical outlet. The
electrical outlet should not be controlled by a wall switch.
Calls cannot be made from the handset if the base
unit is unplugged or switched off, or if the electrical
power is interrupted.
Potential TV Interference: Some cordless telephones
operate at frequencies that may cause interference to TVs
and VCRs. To minimize or prevent such interference, do
not place the base unit of the cordless telephone near or on
top of a TV or VCR. If interference is experienced, moving
the cordless telephone farther away from the TV or VCR
will often reduce or eliminate the interference. (Applies to
25-channel cordless phones only.)
Pt1_1yr_Eng_China_3ATT
7/18/01
10:25 AM
Page 3
Rechargeable Batteries: This product contains either
Nickel-Cadmium or Nickel-Metal Hydride rechargeable
batteries. Exercise care in handling batteries in order not to
short the battery with conducting material such as rings,
bracelets, and keys. The battery or conductor may overheat
and cause harm. Observe proper polarity between the
battery and the battery charger.
Nickel-Cadmium Rechargeable Batteries: Must be
recycled or disposed of properly. Do not dispose of in
household garbage. Do not burn or puncture. Like other
batteries of this type, if burned or punctured, they could
release caustic material which could cause injury.
The RBRC™ Seal means that the manufacturer
is voluntarily participating in an industry
program to collect and recycle NickelCadmium rechargeable batteries when taken
out of service within the United States. These
batteries may be taken to a participating local retailer of
replacement batteries or recycling center. Or you may call
1 800 8BATTERY for locations accepting spent NickelCadmium Batteries.
Nickel-Metal Hydride Rechargeable Batteries: Dispose of
these batteries in a safe manner. Do not burn or puncture.
Like other batteries of this type, if burned or punctured, they
could release caustic material which could cause injury.
Precautions for Users of
Implanted Cardiac Pacemakers
Cardiac Pacemakers (applies only to 900 MHz Digital
Cordless Telephones):
Wireless Technology Research, LLC (WTR), an independent
research entity, led a multidisciplinary evaluation of the
interference between portable wireless telephones and
implanted cardiac pacemakers. Supported by the U.S.
Food and Drug Administration, WTR had recommended to
physicians that:
PACEMAKER PATIENTS
• Should keep wireless phones at least six inches from the
pacemaker
• Should NOT place wireless phones directly over the
pacemaker, such as in a breast pocket, when it is turned ON
• Should use the wireless phone at the ear opposite the
pacemaker
WTR’s evaluation did not identify any risk to bystanders with
pacemakers from other persons using wireless phones.
Pt1_1yr_Eng_China_3ATT
7/18/01
10:25 AM
Page 4
Especially About
Telephone Answering Systems
Two-Way Recording: This unit does not sound warning
beeps to let the other party know that the call is being
recorded. To ensure that you are in compliance with any
federal or state regulations regarding recording a telephone
call, you should start the recording process and then inform
the other party that you are recording the call.
FCC Registration and Repair Information
This telephone product has been registered with the
Federal Communications Commission (FCC) in accordance
with Part 68 of its rules. The FCC requires us to tell you the
following information.
1 Connection and use with the nationwide
telephone network
An FCC compliant telephone cord and modular plug
is provided with this product. This product is designed
to be connected to the telephone network or premises
wiring using a compatible modular jack which is
Part 68 compliant; for a single line use jack RJ11, for
two lines use RJ14. See Installation instructions in the
user’s manual.
This equipment may not be used with Coin
Telephone Lines or with Party Lines.
2 Notification to the telephone company
Upon request of your local telephone company, you
are required to provide them with the following
information:
a The “line” to which you will connect the telephone
equipment (that is, your phone number), and
b The telephone equipment’s FCC registration number
and ringer equivalence number (REN). These numbers
are on the back or bottom of your telephone
equipment.
The REN is useful to determine how many devices
you may connect to your telephone line and still
have them ring when you are called. In most, but not
all areas, the sum of all RENs should be five or fewer.
You may want to contact your local telephone
company for more information.
3 Repair instructions
If it is determined that your telephone equipment is
malfunctioning, the FCC requires that it not be used and
Pt1_1yr_Eng_China_3ATT
7/18/01
10:25 AM
Page 5
that it be unplugged from the modular jack until the
problem has been corrected. Repairs to this telephone
equipment can only be made by the manufacturer or its
authorized agents or by others who may be authorized
by the FCC. For repair procedures, follow the instructions
outlined under the Limited Warranty.
4 Rights of the telephone company
If this telephone product is causing harm to the telephone
network, the telephone company may temporarily
discontinue your telephone service. The telephone
company is required to notify you before interrupting
service. If advance notice is not practical, you will be
notified as soon as possible.
You will be given the opportunity to correct the problem
and the telephone company is required to inform you of
your right to file a complaint with the FCC.
Your telephone company may make changes in its
facilities, equipment, operation, or procedures that
could affect the proper functioning of this product. The
telephone company is required to notify you if such
changes are planned.
5 This telephone is compatible with inductively
coupled hearing aids. (NOTE: This applies only if this
product is equipped with a corded or cordless handset.)
6 Programming/testing of emergency numbers
If this product has memory dialing locations, you may
choose to store police, fire department and emergency
medical service telephone numbers in these locations. If
you do, please keep three things in mind:
a We recommend that you also write the telephone
number on the directory card, so that you can still
dial the emergency number manually if the memory
dialing feature doesn’t work.
b This feature is provided only as a convenience, and
the manufacturer assumes no responsibility for
customer reliance upon the memory feature.
c Testing the emergency telephone numbers you have
stored is not recommended. However, if you do
make a call to an emergency number:
• You must remain on the line and briefly explain
the reason for the call before hanging up.
• Programming/testing of emergency numbers
should be performed during off-peak hours, such
as in the early morning or late evening, when the
emergency services tend to be less busy.
Pt1_1yr_Eng_China_3ATT
7/18/01
10:25 AM
Page 6
Interference Information:
Part 15 of FCC Rules
Some telephone equipment generates, uses, and can
radiate radio-frequency energy and, if not installed and
used properly, may cause interference to radio and
television reception.
This product has been tested and found to meet the
standards for a Class B digital device, as specified in Part 15
of the FCC Rules. These specifications are designed to
provide against such interference in a residential installation.
However, there is no guarantee that interference will not
occur in a particular installation.
If this product causes interference to radio, VCR or
television reception when it’s in use, you might correct the
interference with any one or all of these measures:
— Where it can be done safely, re-orient the receiving
radio, VCR or television antenna.
— To the extent possible, relocate the radio, VCR,
television or other receiver with respect to the
telephone equipment.
— If this telephone product runs on AC power, plug your
product into an AC outlet that’s not on the same circuit
as one used by your radio, VCR or television.
Modifications to this product, not expressly
approved by the manufacturer, could void the user’s
authority to operate the equipment.
Pt1_1yr_Eng_China_3ATT
7/18/01
10:25 AM
Page 7
Limited Warranty
1 WHAT DOES THIS LIMITED WARRANTY COVER?
The manufacturer of this AT&T-branded product,
Advanced American Telephones (“AAT”), warrants to the
holder of a valid proof of purchase (“CONSUMER” or
“YOU”) that the product and all accessories provided by
AAT in the sales package (“PRODUCT”) are free from
material defects in material and workmanship, pursuant to
the following terms and conditions, when installed and
used normally and in accordance with operation
instructions. This limited warranty extends only to the
CONSUMER for PRODUCTS purchased and used in the
United States of America.
2 WHAT WILL AAT DO IF THE PRODUCT IS NOT FREE
FROM MATERIAL DEFECTS IN MATERIALS AND WORKMANSHIP
DURING THE LIMITED WARRANTY PERIOD (“MATERIALLY
DEFECTIVE PRODUCT”)?
During the limited warranty period, AAT’s authorized
service representative will repair or replace, at AAT’s
option, without charge, a MATERIALLY DEFECTIVE
PRODUCT. If AAT repairs this PRODUCT, AAT may use
new or refurbished replacement parts. If AAT chooses to
replace this PRODUCT, AAT may replace it with a new or
refurbished PRODUCT of the same or similar design. AAT
will return repaired or replacement PRODUCTS to YOU
in working condition.
AAT will retain defective parts, modules, or equipment.
Repair or replacement of PRODUCT, at AAT’s option, is
your exclusive remedy. YOU should expect the repair or
replacement to take approximately 30 days.
3 HOW LONG IS THE LIMITED WARRANTY PERIOD?
The limited warranty period for the PRODUCT extends
for ONE (1) YEAR from the date of purchase.
If AAT repairs or replaces a MATERIALLY DEFECTIVE
PRODUCT under the terms of this limited warranty, this
limited warranty also applies to repaired or replacement
PRODUCTS for a period of either (a) 90 days from the
date the repaired or replacement PRODUCT is shipped to
YOU or (b) the time remaining on the original one-year
limited warranty, whichever is longer.
4 WHAT IS NOT COVERED BY THIS LIMITED WARRANTY?
This limited warranty does not cover:
a PRODUCT that has been subjected to misuse,
accident, shipping or other physical damage, improper
installation, abnormal operation or handling, neglect,
inundation, fire, water, or other liquid intrusion; or
Pt1_1yr_Eng_China_3ATT
7/18/01
10:25 AM
Page 8
b PRODUCT that has been damaged due to repair,
alteration, or modification by anyone other than an
authorized service representative of AAT; or
c PRODUCT to the extent that the problem experienced
is caused by signal conditions, network reliability or
cable or antenna systems; or
d PRODUCT to the extent that the problem is caused by
use with non-AAT accessories; or
e PRODUCT whose warranty/quality stickers, product
serial number plates or electronic serial numbers have
been removed, altered or rendered illegible; or
f PRODUCT purchased, used, serviced, or shipped for
repair from outside the United States, or used for
commercial or institutional purposes (including but not
limited to PRODUCTS used for rental purposes); or
g PRODUCT returned without valid proof of purchase
(see 6 below); or
h charges for installation or setup, adjustment of
customer controls, and installation or repair of systems
outside the unit.
5 HOW DO YOU GET WARRANTY SERVICE?
To obtain warranty service in the United States of America,
call 1 800 222–3111 for instructions regarding where to
return the PRODUCT. Before calling for service, please
check the user’s manual. A check of the PRODUCT
controls and features may save YOU a service call.
Except as provided by applicable law, YOU assume the
risk of loss or damage during transit and transportation and
are responsible for delivery or handling charges incurred
in the transport of PRODUCT(S) to the service location.
AAT will return repaired or replaced PRODUCT under
this limited warranty to YOU, transportation, delivery or
handling charges prepaid. AAT assumes no risk for
damage or loss of the PRODUCT in transit.
If the PRODUCT failure is not covered by this limited
warranty, or proof of purchase does not meet the terms of
this limited warranty, AAT will notify YOU and will
request that YOU authorize the cost of repair prior to any
further repair activity. YOU must pay for the cost of repair
and return shipping costs for the repair of PRODUCTS
that are not covered by this limited warranty.
6 WHAT MUST YOU RETURN WITH THE PRODUCT TO GET
WARRANTY SERVICE?
YOU must:
a return the entire original package and contents
including the PRODUCT to the AAT service location
Pt1_1yr_Eng_China_3ATT
7/18/01
10:25 AM
Page 9
along with a description of the malfunction or
difficulty;
b include “valid proof of purchase” (sales receipt)
identifying the PRODUCT purchased (PRODUCT
model) and the date of purchase or receipt (keep a
copy for your records); and
c provide your name, complete and correct mailing
address, and telephone number.
7 OTHER LIMITATIONS
This warranty is the complete and exclusive agreement
between YOU and AAT. It supersedes all other written or
oral communications related to this PRODUCT. AAT
provides no other warranties for this PRODUCT. The
warranty exclusively describes all of AAT’s responsibilities
regarding the PRODUCT. There are no other express
warranties. No one is authorized to make modifications to
this limited warranty and YOU should not rely on any
such modification.
State Law Rights: This warranty gives YOU specific legal
rights, and YOU may also have other rights which vary
from state to state.
Limitations:
Implied warranties, including those of fitness for a
particular purpose and merchantability (an
unwritten warranty that the PRODUCT is fit for
ordinary use) are limited to one year from date of
purchase.
Some states do not allow limitations on how long an
implied warranty lasts, so the above limitation may not
apply to YOU.
In no event shall AAT be liable for any indirect,
special, incidental, consequential, or similar
damages (including, but not limited to lost profits or
revenue, inability to use the PRODUCT, or other
associated equipment, the cost of substitute
equipment, and claims by third parties) resulting
from the use of this PRODUCT.
Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above
limitation or exclusion may not apply to YOU.
Pt1_1yr_Eng_China_3ATT
7/18/01
10:25 AM
Page 10
Please retain your receipt as your proof of purchase.
© 2001 Advanced American Telephones.
All Rights Reserved.
Printed in China. Issue 3AT&T 07/01
10

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Create Date                     : 2001:07:18 10:26:23
Producer                        : Acrobat Distiller 3.01 for Power Macintosh
Author                          : 
Creator                         : QuarkXPressª 4.1: LaserWriter 8 8.1.1
Title                           : Pt1_1yr_Eng_China_3ATT
Modify Date                     : 2001:07:18 10:30:13
Page Count                      : 10

EXIF Metadata provided by EXIF.tools