WISOL ATM100 AUDIO TRANSCEIVER User Manual

WISOL CO., LTD AUDIO TRANSCEIVER ATM100

a href="https://usermanual.wiki/WISOL" itemprop="url"> WISOL >

User Manual

                                                                                                                                ATM100  Version 1.0    page 1 of 14   OEM Integrators / User Manual  1. Introduction  The ATM100 module offers customers fast time to market with a mono, or stereo, wireless audio connection. The module is optimized for low-cost, high-quality, easy-to-use wireless audio solutions for wireless subwoofer or wireless rear speaker applications. Avnera’s proprietary wireless system takes a new approach to wireless audio. The wireless protocol was designed from the ground up and delivers uncompressed mono or stereo audio, with fixed latency over the air, without interference issues, and with industry leading WiFi coexistence – even at close proximities to a WiFi device. Avnera-enabled wireless modules offer a low-touch, easy-to-integrate wireless audio solution and enables fast time to market by eliminating concerns about compliance, antenna tuning, and board optimization. Modules based on Avnera’s AV6210 silicon provide breakthrough wireless audio functionality with fixed low-latency point-to-point transport of uncompressed mono/stereo PCM audio data supporting a wide range of input sample rates. A single I2S digital audio port is used for the module audio input/output.   2. Feature   Product Size ‐ Module Size (mm): 40.4 (W) X 26.0 (L) X 3.2 (H) ‐ Antenna Type : PCB Printed Antenna   Audio Interfaces ‐ I2S Digital Input/Output interface with  >94dB end-to-end digital audio path   2.4 GHz ISM band, continuous dynamic channel selection  Forward error correction coding, error detection, and audio-specific error concealment   Dual onboard printed PCB antennas for multipath and fading mitigation  Auto-search/synch and dynamic channel selection  Low, fixed latency of less than 20ms for typical audio applications  24 pin FPC or pin header connector  Sample rate converter: Support for 32 - 96kHz input sample rates  Over-the-air upgrade capability  Customizable firmware for simple, low-cost, sub-woofer amplifier implementations  General purpose over-the-air (OTA) serial interface:  > 11 kbps, bi-directional, full duplex  Support for amplifier control data, meta-data data, and remote commands
                                                                                                                                ATM100  Version 1.0    page 2 of 14         3. General Function  The ATM100 module is available in 2 variations; digital input transmitter module or digital output receiver module. There is a separate I2S port for digital audio input and output functions and either of these can be configured to be a master or a slave – only the input or output port can be active at any time. In addition, MCLK can be generated from the module, or input to the module as required by the system application.  The highly integrated nature of the AV6210 transceiver IC results in few external components being required for the ATM100 module design. 2 PCB antennas are used to achieve increased range, and to offer diversity, and the simple RF path consists only of the antennas, associated tuning components, the RF switch and a LC balun connected to the AV6210 IC. A 16MHz crystal generates the AV6210 system clock signal used as the basis for all RF and digital audio signals. In addition, a 2Mb flash memory stores the factory based firmware, as well as firmware upgrade images and configuration parameters. The module firmware enables upgrades to be performed by the I2C slave interface or over-the-air. The module can be controlled from an external host device via the I2C interface. The I2C master port allows the module to control other system audio devices such as a sub-woofer amplifier system without having to add another MCU to the product design. Up to a maximum of 17 GPIOs are supported with the ATM100 module including I2C and I2S signals. This large number of GPIOs can be leveraged to Implement low cost sub-woofer designs as outlined below.  The ATM100 module offers a standard and low latency firmware with different over the air sample rate. While the standard 22.2KSps over the air sample rate optimizes audio quality and WiFi coexistence performance; Lower audio latency can be achieved by using the low-latency 44.4KSps over the air sample rate.
Download:
Mirror Download [FCC.gov]
Document ID3684490
Application IDEEapBrb0SQ7AdKGnbdch2A==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize33.5kB (418735 bits)
Date Submitted2017-12-19 00:00:00
Date Available2017-12-19 00:00:00
Creation Date2017-12-19 14:10:20
Producing SoftwareAcrobat Distiller 11.0 (Windows)
Document Lastmod2017-12-19 14:10:20
Document TitleMicrosoft Word - ATM100_User manual_수정
Document CreatorPScript5.dll Version 5.2.2
Document Author: hwj
FCC ID Filing: 2ABA2ATM100

Navigation menu