WaveIP GAOFDM900-RSU Indoor Transmitter Unit User Manual Part 1
WaveIP Ltd. Indoor Transmitter Unit Users Manual Part 1
WaveIP >
Contents
- 1. Users Manual Part 1
- 2. Users Manual Part 2
Users Manual Part 1
August 2005
GigAccess
GigAccessGigAccess
GigAccess
TM
TM TM
TM
OFDM 900
OFDM 900 OFDM 900
OFDM 900
Self
SelfSelf
Self-
--
-Install RSU
Install RSU Install RSU
Install RSU
User Guide
User GuideUser Guide
User Guide
Page
2 of 2
Table of Contents
1. INTRODUCTION ...........................................................................................................3
1.1. G
ENERAL
.............................................................................................................................3
1.2. G
IG
A
CCESS
TM
OFDM 900 S
YSTEM
O
VERVIEW
......................................................................3
2. PACKING LIST..............................................................................................................4
3. INSTALLATION PROCESS ..........................................................................................5
3.1. G
ENERAL
.............................................................................................................................5
3.2. B
EFORE
Y
OU
S
TART
.............................................................................................................6
3.3. I
NSTALLATION
.......................................................................................................................6
3.4. R
ADIO
C
HANNEL
S
ELECTION
.................................................................................................7
3.5. U
SER
PC S
ETUP
..................................................................................................................7
3.6. S
AFETY
................................................................................................................................7
3.7. FCC I
NFORMATION
...............................................................................................................8
4. GIGACCESS
TM
OFDM 900 RSU TECHNICAL SPECIFICATIONS ..............................9
Table of Figures
Figure
1-1: General Description of typical sector in GigAccess™ OFDM 900 System ................... 3
Figure
2-1: RSU package contents ................................................................................................ 4
Figure
3-1: Description of Self Install GigAccess™ OFDM 900 RSU ............................................. 5
Figure
3-2: GigAccess™ RSU - Installation Scheme...................................................................... 7
Page
3 of 3
1. Introduction
1.1. General
Congratulations on your purchase of the WaveIP GigAccess™ OFDM 900 self-install
Business/Residential Subscriber Unit (RSU).
This document describes how to install and use your subscriber unit to obtain wireless high-speed
Internet access. You can connect your RSU both to a computer and to a local area network (LAN)
through the integrated two ports.
1.2. GigAccess
TM
OFDM 900 System Overview
GigAccess
TM
OFDM 900 is WaveIP’s wireless point-to-multipoint broadband communication
system. The basic subsystem – a Sector, consists of an AU (Access Unit) and up to 128
Subscriber Units (SUs) Each with full-duplex communication SUs and the WAN via the AU.
Figure
1-1 depicts a general description of a typical sector in the GigAccess™ OFDM 900 system.
Base Controller
(Option)
AU
AU
Switch/Router
SU
SU
WAN
RSU
BSU
Figure 1-1: General Description of typical sector in GigAccess™ OFDM 900 System
Page
4 of 4
2. Packing List
When you first open the package, verify that the unit is complete and consists:
• RSU Unit
• Power Supply
• Quick Start Guide
Figure 2-1 illustrates the RSU package contents.
GiAccess
TM
Self-Install RSU
User Guide
Quick Start
Guide
Figure 2-1: RSU package contents
Page
5 of 5
3. Installation Process
3.1. General
The RSU is a self-installed, plug and play unit, which requires minimum operation from the user.
A description of the RSU is given in the figure below.
1. Polarization Indication
2. Air link led (Green)
3. ETH link led (Yellow)
4. Received Signal Indicator Lights
5. ETH Connector
6. Power led
7. DC Power Jack
Figure 3-1: Description of Self Install GigAccess™ OFDM 900 RSU
1
4
7
6
5
3
2
Page
6 of 6
3.2. Before You Start
1) Make sure your computer is equipped with an Ethernet Network Interface (NIC)
2) Make sure your computer is set up to automatically obtain an IP address (See 0).
3) Select the appropriate location for the RSU:
• Make sure you are operating the RSU in a room near an outside window.
• Locate the RSU in such a way that the antenna side will be directed towards your
service provider (AU direction).
• Obtain a clear line of site to the AU as much as possible - avoid any physical
obstacles, which may block the signal.
• Your RSU comes with a 1.5m category-5 Ethernet cable. If you choose to place the
RSU. If you purchase a longer cable, make sure the cable is a category-5 Ethernet
cable with RJ-45 connector on each side.
3.3. Installation
The installation process should follow the following steps:
1) Connect the CAT5 Ethernet cable from the RSU data port to your PC NIC. Note that your
RSU consists two Ethernet ports, so you can connect your PC to either of them, or to
connect two PCs each PC to different Ethernet connector.
2) Connect the power supply to the AC wall socket and to the RSU DC power port.
WARNING! Use only with the supplied Power Supply adapter
3) Align the RSU until you get the maximum receive signal from your service provider. Best
received indication when maximum “Received Power Indication leds” are light. Check both
vertical and horizontal polarization and select the polarization that gives you the best
receiving power. The RSU antenna polarization must be the same as in the AU antenna.
In most applications, the preferred orientation is vertical polarization. (Above ground
propagation of the signal is better when it is polarized vertically).
4) The RSU will automatically acquire the radio channel of the AU.
• Verify that the Air link led flashes (green led on the Ethernet connector), which
indicated reception from the AU.
• Verify that the Ethernet link led light (yellow led on the Ethernet connector) when the
PC is connected. This led will flash in case of Ethernet data transaction between the
RSU and the PC.
Now you are ready to surf into the Internet.
WARNING! Do not put any obstacle in front antenna. A minimum separation distance of 20 cm
(8 inches) must be maintained between the device in operation and all persons.
Page
7 of 7
AU
Direction
Ethernet
Data Cable
CAT5
Power
Supply
100-240V AC
RSU
Figure 3-2: GigAccess™ RSU - Installation Scheme
3.4. Radio Channel Selection
The radio channel is defined at the AU side.
The RSU is pre-configured to scan all channels. Therefore it will acquire the AU channel
automatically.
3.5. User PC Setup
Configure the PC NIC to obtain an IP address from DHCP server.
For this configuration follow the following steps:
• Press right click on the Network Neighborhood Icon.
• Select the Protocol tab and press properties.
• Choose Obtain an IP address from DHCP server.
3.6. Safety
1. Do not immerse the equipment in any type of liquid.
2. Only operate the equipment from the power source(s) Supplied by Manufacturer! Any other
type of input power source may cause damage to the equipment and voids the warranty.
3. Do not place the equipment on an unstable surface.
4. Do not disassemble the equipment. Removing covers voids the warranty.
5.
Do not expose the equipment to extreme hot or cold temperatures.
Page
8 of 8
3.7. FCC Information
Notice: This device has been tested and found to comply with Radio Frequency Exposure Limits.
A minimum separation distance of 30 cm must be maintained between the device in operation and
all persons.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
This device Complies With FCC Standards
FOR HOME OR OFFICE USE
FCC Notice, USA
This equipment has been tested and found to comply with the limits for Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient the relocate-receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device must accept any interference received including interference that may cause
undesired operation. Any unauthorized modification or changes to this device without the express
approval of WaveIP may void the user’s authority to operate this device. Furthermore, this device
intended to be used only when installed in accordance with the instructions outlined in this
manual. Failure to comply with these instructions may also void the user’s authority to operate this
device and/or the manufacturer’s warranty
Page
9 of 9
4. GigAccess
TM
OFDM 900 RSU Technical Specifications
Operating Frequency 902 – 928MHz ISM band
Number of Channels 7 (912 – 918) in step of 1MHz
Access technology TDMA (Time division multiple access)
Duplexing schemes TDD (Time division duplex)
RF Waveform OFDM
Raw Data Rates 6, 18 Mbps
Data Throughput Up to 5.0 Mbps for RSU
Radio Sensitivity @18 Mbps: -80 dBm, IE-2 PER1
@6 Mbps: -82 dBm, IE-2 PER
EIRP 36 dBm (max)
Antenna Gain 6.5 dBi
Antenna Polarization Vertical or Horizontal
Wireless MAC Interface Proprietary based on IEEE 802.16a
Physical Interface 2 x 10/100 Base-T (RJ-45)
Protocol Supported IP, ICMP, ARP, TCP, UDP, DHCP, and HTTP
Software Update Over the Air Download via TFTP
Operating Temperature 0°C - +40°C
Power 3.3 VDC, < 5 Watt
AC Input Voltage 100 – 240 VAC, 47 – 63 Hz
Mechanical 160 mm x 160 mm x 45 mm