Westell CSI610-S9 Single Band Bidirectional Amplifier User Manual

Westell, Inc. Single Band Bidirectional Amplifier Manual Morph Rev2

a href="https://usermanual.wiki/Westell" itemprop="url"> Westell >

Exhibit D Users Manual per 2 1033 c3

MORPH MANUAL WORD FORMAT Table of Contents Product Registration/Certification Information................1 Safety Guidelines.....................................................…..1 Product Information....................................................…2 Pin-Out Chart..............................................…..2 LED Indicators.............................................…..2 Mechanical Outline Drawing..........................…3 Installation..............................................................…….4 Important Safety Information....................................…..5 Amplifier Adjustment.................................................….6-9 Troubleshooting........................................................….10 Product Warranty.....................................................…..11 Product Certification/Registration Information The serial number may be found on the label on the rear panel of the unit. For your convenience, note this number below. Retain this manual, along with proof of purchase, to serve as a permanent record of your purchase for future reference or in the event of theft. Safety Guidelines The general safety information in this guideline applies to both operating and service personnel. Specific warnings and cautions will be found in other parts of this manual where they apply, but may not appear in this summary. Failure to comply with these precautions or specific warnings elsewhere in the manual violates safety standards of design, manufacture, and intended use of equipment. Cellular Specialties, Inc. assumes no liability for the customer’s failure to comply with these requirements. Grounding This amplifier system is designed to operate from 120 Vac @ 1.3A maxpower and should always be operated with the ground wire properly connected. Do not remove or otherwise alter the grounding lug on the power cord. Explosive Atmospheres This product has an integral circuit breaker, which may cause an electrical flash if the breaker should reset. To avoid explosion or fire, do not operate this product in the presence of flammable gases or fumes.
Lightning Danger Do not install or make adjustments to this unit during an electrical storm. No User Serviceable Parts Inside HAZARDOUS VOLTAGES ARE PRESENT WHEN THE COVER IS REMOVED. Opening the chassis will void your warranty. If you suspect a malfunction with this product, call your dealer or the Cellular Specialties Support Line at (603) 626-6677. DISCLAIMER: All information and statements contained herein are accurate to the best of the knowledge of Cellular Specialties, Inc. (CSI), but Cellular Specialties makes no warranty with respect there to, including without limitation any results which may be obtained from the products described herein or the infringement by such products of any proprietary rights of any persons. Use or application of such information or statements is at the users sole risk, without any liability on the part of Cellular Specialties, Inc. Nothing herein shall be construed as license or of recommendation for use, which infringes upon any proprietary rights of any person. Product material and specifications are subject to change without notice. Specialties’ standard terms of sale and the specific terms of any particular sale. Product Description Cellular Specialties, Inc. (CSI) developed the LCD Model Bi-Directional Amplifier (BDA) for use in enclosed structures where sufficient signal from local cell sites to operate cell phones was unavailable within the building. It is necessary that sufficient signal be available on the roof of the structure. The BDA is connected to an external antenna, usually on the roof, and to one or more internal antennas placed strategically throughout the area where phone service is desired. The external antenna is usually a directional type such as a “Yagi”. Internal antennas are usually omni directional, although various other types may be used for certain installations. The BDA amplifies both the “uplink” (phone to tower) and “downlink” (tower to phone) signals thus facilitating communications to and from the local cell site. There are seven amplification stages on the downlink and seven on the uplink for a total of +80dB nominal gain for each link. Gain can be set using the LCD display and select/up/down switches. There are also LED indicators on the top cover for power overload and gain reduction to prevent oscillation. LED Indicators Warning: The unit has sensed instability due to insufficient isolation between the inside antenna and the outside antenna, and has reduced the gain of the amplifier. This is done to prevent oscillation, which can interfere with the handsets in the covered area and/or the wireless service provider’s base station. Fault: The gain of the unit has been reduced to a minimum in order (Red) to prevent very strong input signals from overloading the amplifier. The amplifier will attempt to recover from this condition, initially at fifteen-second intervals and then at four-minute intervals. An automatic amplifier safety shutdown circuit is also incorporated that will disable the transmitters should the uplink or downlink overloads be reached to prevent excessive intermodulation and oscillation. The amplifier will periodically attempt to recover from this condition. The BDA is also equipped with an interface connector (RJ-15) designed for use with an optional remote monitor. A second Connector (RJ-11) is used for remote monitoring and shutdown. The RJ-11 pin-out is listed below. Pin-Out Chart Pin Description 1 Alarm Relay - Common 2 N/C 3 Shutdown (Input TTL) 4 Uplink Power 5 Alarm Relay – Active Open 6 N/C
Download:
Mirror Download [FCC.gov]
Document ID540953
Application IDVf0Dx6JjbZENcc7/1C+kPQ==
Document DescriptionExhibit D Users Manual per 2 1033 c3
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize23.96kB (299494 bits)
Date Submitted2005-05-11 00:00:00
Date Available2005-05-10 00:00:00
Creation Date2004-11-15 15:39:39
Producing SoftwareAcrobat Distiller 5.0 (Windows)
Document Lastmod2004-11-15 15:39:39
Document TitleMicrosoft Word - Manual Morph Rev2.doc
Document CreatorPScript5.dll Version 5.2
Document Author: Burton
FCC ID Filing: NVRCSI610-S9

Navigation menu