White Conveyors 6500-60-AA Remote Control User Manual users manual
White Conveyors, Inc. Remote Control users manual
Contents
- 1. users manual
- 2. advertising literature
users manual
1
IMPORTANT MANUAL
Do Not Throw Away
Save These Instructions
Wardrobe valet
Owners Manual
Models CW-100- CW-200
Closet Conveyor
WARNING: Read this Manual and follow all Warnings and Safety
Instructions. Failure to do so can result in Injury.
2
ATTENTION!
YOUR WARDROBE VALET CONVEYOR DOES NOT
HAVE ANY USER SERVICEABLE PARTS.
YOUR WARDROBE VALET CONVEYOR SHOULD
NOT BE ADJUSTED OR REPAIRED BY ANYONE
EXCEPT PROPERLY QUALIFIED SERVICE
PERSONNEL.
For help with your conveyor, please call White Conveyors, Inc., Field
Service Department toll-free, at:
1-800-524-0273
3
TABLE OF CONTENTS
DESCRIPTION PAGE
Important Safety Instructions 4-6
Product Specifications 7
Installation Instructions 8-17
Operation Instructions 17
Troubleshooting 18
Limited Warranty 19
Contact Information 19
ETL Certification 20
FCC Certification and Guidelines 22
4
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING YOUR
WARDROBE VALET CONVEYOR
SAVE THESE INSTRUCTIONS
Your Wardrobe valet Conveyor can be used as household appliance. Read this
manual carefully. Be thoroughly familiar with the controls and the proper use of
Wardrobe valet Conveyor. Know how to stop the Wardrobe valet Conveyor
quickly.
Never allow children to operate the Wardrobe valet Conveyor without
supervision. Never allow adults to operate the Wardrobe valet Conveyor without
proper instructions.
Do Not Operate Wardrobe valet Conveyor if it is damaged. Disconnect power
cord immediately if Wardrobe valet Conveyor is damaged.
Do Not Operate Wardrobe valet Conveyor if it has a damaged power cord or plug.
Do Not Operate Wardrobe valet Conveyor if Remote control is damaged or does
not function properly, for example if conveyor chain does not move when button
on Remote is pressed, or does not Stop immediately when button on remote is
Released.
DISCONNECT POWER CORD IMMEDIATELY IF CONVEYOR DOES NOT
STOP WHEN BUTTON ON REMOTE CONTROL RELEASED.
To disconnect conveyor, make sure that conveyor chain does not move, than
remove plug from outlet.
Do Not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
WARNING: Do Not wash conveyor. Wipe with dry cloth only. Unplug
conveyor from outlet before cleaning.
WARNING: Conveyor must be installed so the distance from floor to the lowest
point of conveyor chain must be 6 Ft or greater
Do Not place any objects or clothes on tubes or on sprocket, it could damage
your conveyor and your items.
Do Not load Wardrobe valet Conveyor with anything other than goods on
hangers.
5
Do Not obstruct Conveyor chain movement.
Do Not touch any Wardrobe valet Conveyor parts when conveyor is moving.
Do Not allow anyone to hang or climb on Wardrobe valet Conveyor chain. Keep
fingers out of the “pinch point” areas; the distance between sprocket and chain is
necessary small, and the rollers riding over the tube. Those areas must be
protected by location – the minimal distance from the floor to the bottom of chain
must be 6 Ft or greater.
Do Not use this product near water – for example, in wet basement, near a
swimming pool.
Stay away at least 2 ft from conveyor chain when conveyor is moving.
Install or locate your Wardrobe valet Conveyor only in accordance with provided
Installation instruction.
Use your Wardrobe valet Conveyor only for its intended use as described in this
manual.
Keep power cord away from heated surfaces.
Do not immerse power cord or plug in water.
Your Wardrobe valet Conveyor must be grounded. Connect only to properly
grounded outlet.
DO NOT any circumstances, cut or remove the third (ground) prong from power
cord. SEE GROUNDING INSTRUCTIONS on page ???
To reduce the risk of injury, close supervision is necessary when Wardrobe valet
Conveyor is used near children.
CAUTION: Items of interest to children should not be stored on shelves or in
cabinets above your Wardrobe valet Conveyor – children climbing on conveyor to
reach items could be seriously injured.
Your Wardrobe valet Conveyor is intended for indoor usage only.
The conveyor does not use or produce hazardous materials, and or
grinding/lubricant exhaust. It does not require special ventilation.
Your Wardrobe valet Conveyor must be loaded and unloaded when conveyor
chain is not moving (completely stopped).
6
GROUNDING INSTRUCTIONS
Your Wardrobe valet Conveyor must be grounded. In the event of malfunction
or breakdown, grounding provides a path of least resistance for electronic current
to reduce the risk of electric shock. Your Wardrobe valet Conveyor is equipped
with cord having an equipment grounding conductor and grounding plug. The
plug must be plugged into an appropriate outlet that is properly installed and
grounded in accordance with all local codes and ordinances.
DANGER: Improper connection of the equipment-grounding conductor can
result in a risk of electric shock.
The conductor with insulation having an outer surface that is green with or
without yellow stripes is the equipment-grounding conductor. Check with
qualified electrician or serviceman if the grounding instructions are not
completely understood, or if in doubt as to whether the appliance is properly
grounded. DO NOT modify the plug provided with your Wardrobe valet
Conveyor – if it will not fit the outlet, have a proper outlet installed by a qualified
electrician.
Your Wardrobe valet Conveyor is cord connected appliance rated less than 15 A
and intended for use on nominal 120 V supply circuit and has a grounding plug
that looks like the plug illustrated in sketch below.
DO NOT use an adaptor plug with this appliance.
For best operation, plug this appliance into its own electrical outlet to prevent
flickering of light, blowing of fuse or tripping of circuit breaker.
GROUNDING PLUG AND
GROUNDED OUTLET BOX
GROUNDING PIN
COVER OF GROUNDED
OUTLET BOX
PLUG
7
Product Specifications
Hanging Over
all
Overal
l
Capacity Lengt
h
Width
Product 1-Tier Empty w/Garmen
ts
with Shipping
Number Lengt
h
(Ft.) garme
nts
Weigh
t
CW-100 10 feet 4 Ft 6.00 Ft. 4 Ft. 150 Lbs
.
CW-120 12 feet 6 Ft 8.00 Ft. 4 FT. 160 Lbs
.
CW-140 14 feet 7 Ft 9.00 Ft. 4 FT. 180 Lbs
.
CW-160 16 feet 8 Ft 10.00 Ft. 4 FT. 200 Lbs
.
CW-180 18 feet 9 Ft 11.00 Ft. 4 FT. 220 Lbs
.
CW-200 20 feet 10 Ft 12.00 Ft. 4 FT. 260 Lbs
.
8
INSTALLATION INSTRUCTIONS
1.) Open and inspect the package upon arrival
The package should include the following components:
• Conveyor with motor and chain frames assembled.
• 2 legs
• Leg clips
• Plastic strip to cover holes in legs
9
2.) Carefully remove the conveyor from the packaging. This operation
would normally be performed by two persons.
CAUTION :.
The conveyor is heavy and the machine is heavier on the sprocket side
3.) Remove the legs from the packaging. Also strip the plastic covering
off the package.
10
4.) Stand up the legs and insert the top section in the bottom section.
Insert the locking pins in both legs. Once the legs are positioned this will
be released to raise the conveyor.
5.) Position the conveyor to be able to mount the legs.
11
Example of the proper positioning of the leg in the upper assembly
and proper pin placement.
Side view of pin placement in the upper assembly.
12
Example: This is the lower view of the drive sprocket.
6. Conveyor should then be lifted by two men and both legs should be
positioned and secured.
WARNING: Conveyor must be installed so the distance from floor to the lowest
point of conveyor chain must be 6 Ft or greater.
13
Example: View of the wheel and chain assembly on the conveyor.
Example: Proper hanging position of the drop rods.
14
Example: Left Side view of proper locking pin placement
Example: Right side view of proper locking pin placement
Example: View of rear sway brace for machine. Should be positioned against the
wall and secured with a lag screw.
15
View of drop rods being attached to the Wardrobe valet
Attachment of lower garment rods
16
Finished conveyor
OPERATION INSTRUCTIONS
WARNING: Carefully review Important Safety Instructions in this Manual before
operating your Wardrobe valet closet conveyor.
To move conveyor chain, press the right hand button on your wireless control
and the conveyor will rotate to the right. To stop release the button.
To move the conveyor in the left direction, press and hold the left button. To stop
release the button.
If you need to reverse direction press the opposite button and the conveyor will
move after short time delay. Conveyor will stop when either button is released.
17
TROUBLESHOOTING
YOUR WARDROBE VALET CONVEYOR DOES NOT HAVE ANY USER
SERVICEABLE PARTS.
YOUR WARDROBE VALET CONVEYOR SHOULD NOT BE ADJUSTED OR
REPAIRED BY ANYONE EXCEPT PROPERLY QUALIFIED SERVICE
PERSONNEL.
If you Wardrobe valet Conveyor chain does not move:
Make sure that conveyor chain and sprocket are not jammed by foreign objects.
Make sure that there is power in your grounded outlet box
Make sure that conveyor electrical grounded plug is connected to grounded
outlet box.
WARNING: Do Not Operate Wardrobe valet Conveyor if Remote control is
damaged or does not function properly, for example if conveyor chain does not
move when button on Remote is pressed, or does not Stop immediately when
button on remote is Released.
18
LIMITED EQUIPMENT WARRANTY
New WCI equipment is warranted against defective workmanship and material
for one year from the date of shipment. This includes a 90-day labor (for jobs
sold with installation) and one-year parts warranty.
WCI shall not be responsible for defective installation or erection when
performed by any other than WCI employees, or its authorized installers, nor for
any parts that fail as a result.
WCI shall not be liable for customs duties, brokerage fees, or other costs related
to obtaining warranted replacement parts.
WCI shall, at its discretion, either repair or replace the defective component.
When WCI authorizes a warranty replacement, a Return Authorization Number
(RAN) will be issued to you. All components return shipped to WCI must display
the RAN Number on the exterior of the package. Components returned without
prior authorization and/or the RAN number displayed on the package cannot be
processed. All returns must be shipped to WCI freight prepaid. Other than UPS,
all warranty replacements will be returned to the customer freight collect. Please
contact our Customer Service Department at 1-800-524-0273 to request an RAN
number.
This limited warranty does not cover parts failure due to the customer's
negligence, abuse/misuse, or lack of use of the recommended maintenance
procedures.
This limited warranty will not apply to customers whose payment accounts are
more than thirty (30) days past due.
There are no warranties that extend beyond the face hereof. WCI expressly
disclaims any other warranties including, without limitation, the implied warranty
of merchantability or fitness for a particular purpose. In addition, WCI shall not be
liable for incidental or consequential damages arising from or relating to claims
brought pursuant to this limited warranty or claims under any agreement between
WCI and customer.
Contact Information
Wardrobe valet
c/o White Conveyors Inc.
10 Boright Avenue
Kenilworth, NJ 07033
908-686-5700
1-800-
info@wardrobevalet.com
www.wardrobevalet.com
19
20
FCC Certification Page
Combined FCC and Canada Label
FCC ID:TG26500-60-AA
Model: 6500-60-AA
IC:5989A-650060AA
Country Of Origin USA
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: 1) This device may not cause harmful
interference and 2) This device must accept any
interference that may be received, including
interference that may cause undesired operation.
FCC Guidelines
Changes or modifications not expressly approved by White Conveyors, Inc. could
void the user's authority to operate the equipment. This product has been tested
and complies with the specifications for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and
used according to the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur
in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which is found by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna Increase the separation
between the equipment or devices.
Connect the equipment to an outlet other than the receiver's.
Consult a dealer or an experienced radio/TV technician for assistance".