Wistron NeWeb DNUBAT1 802.11 a/b/g/n 2x2 USB Dongle User Manual

Wistron NeWeb Corporation 802.11 a/b/g/n 2x2 USB Dongle

a href="https://usermanual.wiki/Wistron-NeWeb" itemprop="url"> Wistron NeWeb >

User Manual

English   - 1 -ConnectivityWired ConnectivityTo Connect to a Wired Network• You must have a modem/router connected to an active broadband connection.• Connect your TV to your modem/router via an ethernet cable. There is a LAN port at the rear (back) of your TV.Broadband ISP connectionLAN (ethernet) cableLAN input on the rear side of the TVTo configure wired settings please refer to the Network/Internet Settings section in the System>Settings Menu.• You might be able to connect your TV to your LAN dependingonyournetwork’sconguration.Insucha case, use an ethernet cable to connect your TV directly to the network wall outlet.LAN input on the rear side of the TVnetwork  wall socketConguring Wired Device SettingsNetwork TypeThe Network Type can be selected as Wired Device, Wireless Device  or Disabled, in accordance with the active connection to the TV set. Select this as Wired Device if you are connecting via an ethernet cable.Internet Speed TestHighlight  Internet Speed Test and press the OK button. TV will check the internet connection bandwidth and display the result when complete. Advanced SettingsHighlight  Advanced Settings  and press the OK button. On the next screen you can change the IP and DNS settings of the TV. Highlight the desired one and press Left or Right button to change the setting from Automatic to Manual. Now you can enter the Manual IP and / or Manual DNS values. Select the related item in the drop down menu and enter the new values using the numeric buttons of the remote. Press the OK button to save settings when complete. Wireless Connectivity To Connect to a Wireless NetworkIMPORTANT: “Veezy 200” USB dongle is required to use wireless network features.The TV cannot connect to the networks with a hidden SSID. To make your modem’s SSID visible, you should change your SSID settings via the modem’s software. To Connect to a wireless LAN, you should perform the following steps:1.  Then connect the wireless adaptor to one of the USB inputs of the TV.2.  Tocongure yourwirelesssettingspleasereferto the Network/Internet Settings section in the System>Settings Menu.Broadband ISP connectionWireless LAN adaptorUSB inputs on the rear left side of the TVA Wireless-N router (IEEE 802.11a/b/g/n) with simultaneous 2.4 and 5 GHz bands is designed to increase bandwidth. These are optimized for smoother and faster HD video streaming, le transfers andwireless gaming.• The frequency and channel differ depending on the area.• The transmission speed differs depending on the distance and number of obstructions between the transmission products, the conguration of theseproducts,theradiowaveconditions,thelinetrafcand the products that you use. The transmission may also be cut off or may get disconnected depending on the radio wave conditions, DECT phones or any other WiFi 11b appliances. The standard values of the transmission speed are the theoretical maximum
English   - 2 -values for the wireless standards. They are not the actual speeds of data transmission.• The location where the transmission is most effective differs depending on the usage environment.• The Wireless LAN adaptor should be connected directly to the TV’s USB port. USB hubs are not supported. You can plug your wi dongle into thesupplied dock in cases where network quality is poor andthewidongleneedstobeplacedtoalocationwith better signal quality.• The Wireless LAN adaptor supports 802.11 a,b,g & n type modems. It is highly recommended that you should use the IEEE 802.11n communication protocol in order to avoid any possible problems while watching videos.• Use the other USB input, if you experience problems with audio/video performance.• You must change your modem’s SSID when there are any other modems around with the same SSID. You can encounter connection problems otherwise. Use a wired connection if you experience problems with a wireless connection. Conguring Wireless Device SettingsTo enable Wi-Fi features, plug in the Wi-Fi dongle to one of the USB ports. Open the Network/Internet Settings menu and select Network Type as Wireless Device to start connection process.The TV will scan the wireless networks automatically. A list of available networks will be displayed. Please select your desired network from the list. Note: If the modem supports N mode, you should set N mode settings.If the selected network is protected with a password, please enter the correct key by using the virtual keyboard. You can use this keyboard via the directional buttons and the OK button on the remote control. Wait until the IP address is shown on the screen.This means that the connection is now established. To disconnect from a wireless network, highlight Network Type  and press Left or Right buttons to set as Disabled.Highlight Internet Speed Test and press the OK button to check your internet connection speed. Highlight Advanced Settings and press the OK button to open the advanced setting menu. Use directional and numeric buttons to set. Press the OK button to save settings when complete. Other InformationThe status of the connection will be displayed as Connected or Not Connected and the current IP address, if a connection is established.Connecting to your mobile device via WiFi• If your mobile device has WiFi feature, you can connect it to your TV via a router, in order to access the content in your device. For this, your mobile device must have an appropriate sharing software.• Connect to your router following the steps stated above in the Wireless Connectivity section.• Afterwards, engage your mobile device with the router and then activate the sharing software on your mobile device. Then,selectlesthatyouwanttosharewithyourTV.• If the connection is established correctly, you will be abletoaccessthesharedlesfromyourmobiledevicevia the Media Browser of your TV.• Enter the Media Browser menu and the playback device selection OSD will be displayed. Select your mobile device and press the OK button to continue.• If available, you can download a virtual remote controller application from the server of your mobile device application provider. Note: This feature may not be supported on all mobile devices.Wake ONWake-on-LAN (WoL) and Wake-on-Wireless LAN (WoWLAN) are standards that allow a device to be turned on or woken up by a network message. The message is sent to the device by a program executed on a remote device connected to the same local area network, such as a smartphone. Your TV is WoL and WoWLAN compatible. To enable this feature set the Wake On option in the Network/Internet Settings menu as On. It is necessary that both the device, from which the network message will be sent to the TV, and the TV are connected to the same network. Wake On feature is only supported for Android OS devices and can only be used via YouTube andNetixapplications.In order to use this feature the TV and the remote device should be connected at least once while the TV is on. If the TV is powered off, the connection should be reestablished, the next time it is switched on. Otherwise this feature will be unavailable. This does not apply, when the TV is switched into the standby mode.The performance of some devices in the market, may vary due to the software architecture. In order to use Wake On feature with a better performance, please makesurethatyourdevicehaslatestrmwareversion.Wireless DisplayWireless Display is a standard for streaming video and sound content by Wi-Fi Alliance. This feature provides the ability to use your TV as wireless display device.
Download:
Mirror Download [FCC.gov]
Document ID3643741
Application ID5LMiYv6eGYPyAKRqD5cZVg==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize16.14kB (201790 bits)
Date Submitted2017-11-17 00:00:00
Date Available2017-11-20 00:00:00
Creation Date2017-11-14 16:52:15
Producing SoftwareAdobe PDF Library 10.0.1
Document Lastmod2017-11-16 13:51:54
Document TitleUser Manual
Document CreatorAdobe InDesign CS6 (Windows)
FCC ID Filing: NKR-DNUBAT1

Navigation menu