Wistron MS2140BG Laptop with Wireless LAN + Bluetooth User Manual manuT60M665

Download:
Mirror Download [FCC.gov]
Document ID	396811
Application ID	pt3RD9B09y9oIBD/wgBf0A==
Document Description	Bluetooth Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	177.35kB (2216927 bits)
Date Submitted	2004-02-13 00:00:00
Date Available	2004-02-13 00:00:00
Creation Date	2004-01-16 14:17:11
Producing Software	Acrobat PDFWriter 4.0 for Windows
Document Lastmod	0000-00-00 00:00:00
Document Title	穨manuT60M665.PDF
Document Creator	穨Microsoft Word
Document Author:	穨Daphne Liu

INSTALLATION MANUAL
T60M665
Bluetooth Modem Combo Module
Ambit Microsystems Corporation國碁電子(股)公司
5F-1, 5 Hsin-An Rd., Hsinchu Science-Based Industrial Park, Hsinchu, Taiwan, R.O.C.
TEL: 886-3-5784975, FAX: 886-3-5782924, Internet: http:\\www.ambit.com.tw\
中華民國臺灣省新竹縣新竹科學園區新安路5號5樓之1
電話886-3-5784975，傳真：886-3-5782924
Contents
SECTION ONE:
1.1
INTRODUCTION...........................................................................................................1
FEATURES ............................................................................................................................................. 1
1.1.1 BLUETOOTH FUNCTION............................................................................................................................ 1
1.1.2 M ODEM FUNCTION .................................................................................................................................... 1
1.2 HARDWARE REQUIREMENTS....................................................................................................................... 2
SECTION TWO: BLUETOOTH INSTALLATION............................................................................................3
2.1
BLUETOOTH INSTALLATION ............................................................................................................ 3
SECTION THREE: MODEM INSTALLATION ..................................................................................................8
3.1
DRIVER INSTALLATION ...................................................................................................................... 8
3.2
AT COMMANDS.................................................................................................................................. 11
SECTION FOUR:
FCC NOTICE................................................................................................................19
4.1
FCC COMPLIANCE ............................................................................................................................. 19
4.2
FCC CLASS B STATEMENT .............................................................................................................. 19
The information contained in this manual has been verified at the time of this manual printing. The
manufacturer reserves the right to make any changes and improvements in the product described in this
manual at any time and without notice.
All registered trademarks are the property of their respective owners.
Ambit Microsystems Corporation國碁電子(股)公司
5F-1, 5 Hsin-An Rd., Hsinchu Science-Based Industrial Park, Hsinchu, Taiwan, R.O.C.
TEL: 886-3-5784975, FAX: 886-3-5782924, Internet: http:\\www.ambit.com.tw\
中華民國臺灣省新竹縣新竹科學園區新安路5號5樓之1
電話886-3-5784975，傳真：886-3-5782924
Section One:
Introduction
The Bluetooth Modem Combo Module is a cost-effective wireless access. The Bluetooth circuit of this
module is compliant to Bluetooth 1.1 standard. With V.92 technology, the modem part can achieve internet
connection rates up to 56 kbits/s with backward compatibility. The V.92 Feature include PCM Upstream,
Modem On Hold, Quick Connection and V.44 Data compression. The Audio CODEC will be placed on the
notebook and contact with Modem Codec by AC-Link Interface. The combo card complies with MDC
Domestic form factor.
1.1 Features
1.1.1 Bluetooth Function
Bluetooth radio firmware is upgradeable for bug fixes, initial version compatible with Bluetooth
specification version 1.1.
Fully compliant to Bluetooth SIG (BQB) compatibility testing.
USB Pin assignment is to use MDC reserve pin to communicate with Host.interface
Bluetooth Profile Support
- General Access Profile
- Service Discovery Application Profile
- Serial Port Profile
- Dial-up Networking Profile
- LAN Access Profile
- Generic Object Exchange Profile
- File Transfer Profile
- Object Push Profile
- Synchronization Profile
Drivers support Windows 98, 98SE, ME, 2000, XP.
Supports Power Management ACPI 1.94 (or later)
o Bluetooth performance must exceed 500 kbps, using OBEX.
1.1.2 Modem Function
AC’97/MC’97 2.2 compliant
Support Modem Digital Line Guard: The product shall incorporate circuitry to sense whenever the
Ambit Microsystems Corporation國碁電子(股)公司
5F-1, 5 Hsin-An Rd., Hsinchu Science-Based Industrial Park, Hsinchu, Taiwan, R.O.C.
TEL: 886-3-5784975, FAX: 886-3-5782924, Internet: http:\\www.ambit.com.tw\
中華民國臺灣省新竹縣新竹科學園區新安路5號5樓之1
電話886-3-5784975，傳真：886-3-5782924
current on the line exceeds approximately 130mA, and should immediately go back on hook.
The call progress signal shall be scaled digitally according to the speaker level setting (ATL1, L2,
L3)
ITU-T V.92 PCM Upstream and V.90 data rates with auto-fallback to V.34, V.32terbo, V.32bis and
fallbacks
TIA/EIA 602 standard for AT Command set
Supports V.42 error correction and V.44, V.42bis/MNP5 data compression
FAX capabilities: ITU-T V.17, V.29, V.27ter, V.21 Ch2 and TIA/EIA 578 Class1 FAX
o Support Wake up on Ring and meet WHQL test requirement..
1.2 Hardware Requirements
Supply Voltage
3.3V & 1.8V
Frequency Range
2.400-2.4835 GHz
Antenna Load
50 Ohm
Receive Sensitivity
–80 dBm@0.1% BER
Maximum Receiver Signal
-20 dBm
TX Power
4 dBm maximum (class 2)
RF Power Control Step Size
2 dB
Range
10 meters at 0 dBm TX power (class 2)
Radio
Compliant with Bluetooth standard version 1.1
Pico Net
1 master to 7 slaves
Operating Channels
79 channels of 1 MHz BW
Security
Full support of Bluetooth security provisions including hardware
support for full length 128 bit encryption keys.
Host Interface (USB)
USB specification 1.1 compliant and using MDC reserve pin to
communicate with Host
Software Requirements
Windows 98SE, ME, 2000, XP.
Mechanical Requirements
27mm x 45mm x 4.7mm(1.2/0.8/2.7mm)
Ambit Microsystems Corporation國碁電子(股)公司
5F-1, 5 Hsin-An Rd., Hsinchu Science-Based Industrial Park, Hsinchu, Taiwan, R.O.C.
TEL: 886-3-5784975, FAX: 886-3-5782924, Internet: http:\\www.ambit.com.tw\
中華民國臺灣省新竹縣新竹科學園區新安路5號5樓之1
電話886-3-5784975，傳真：886-3-5782924
Section Two: Bluetooth Installation
The following steps provide instructions for installing Bluetooth.
1. Make sure your MDC BT/Modem Combo card already insert into your notebook.
2. Make sure your notebook operating system support Windows 98SE or ME or 2000 or XP.
2.1 Bluetooth Installation
Proceed to the following section.
1. Execute the program ‘Setup.exe’ in the CD. Windows displays the dialog as below. Click ‘Next’ to begin
the process.
Ambit Microsystems Corporation國碁電子(股)公司
5F-1, 5 Hsin-An Rd., Hsinchu Science-Based Industrial Park, Hsinchu, Taiwan, R.O.C.
TEL: 886-3-5784975, FAX: 886-3-5782924, Internet: http:\\www.ambit.com.tw\
中華民國臺灣省新竹縣新竹科學園區新安路5號5樓之1
電話886-3-5784975，傳真：886-3-5782924
2.The “License Agreement” windows will pop up, please read it carefully. If you agree it, and choose ‘I agree
the terms in the license agreement’ and click on ‘Next’.
3. “Destination Folder” appears, specify the location of the driver and software to be installed then press
‘Next’ bottom.
Ambit Microsystems Corporation國碁電子(股)公司
5F-1, 5 Hsin-An Rd., Hsinchu Science-Based Industrial Park, Hsinchu, Taiwan, R.O.C.
TEL: 886-3-5784975, FAX: 886-3-5782924, Internet: http:\\www.ambit.com.tw\
中華民國臺灣省新竹縣新竹科學園區新安路5號5樓之1
電話886-3-5784975，傳真：886-3-5782924
4. When all the above process are done, it will show ‘Ready to Install the Program” window. Make sure the
driver software is ready to be installed, click ‘Install’.
Ambit Microsystems Corporation國碁電子(股)公司
5F-1, 5 Hsin-An Rd., Hsinchu Science-Based Industrial Park, Hsinchu, Taiwan, R.O.C.
TEL: 886-3-5784975, FAX: 886-3-5782924, Internet: http:\\www.ambit.com.tw\
中華民國臺灣省新竹縣新竹科學園區新安路5號5樓之1
電話886-3-5784975，傳真：886-3-5782924
5.Choose ‘Install the software automatically [Recommened]’, then Click ‘Next’ to continue.
6. Congratulations! Bluetooth has been installed successfully.
Please click ‘Finish’ to confirm the completion of installation.
Ambit Microsystems Corporation國碁電子(股)公司
5F-1, 5 Hsin-An Rd., Hsinchu Science-Based Industrial Park, Hsinchu, Taiwan, R.O.C.
TEL: 886-3-5784975, FAX: 886-3-5782924, Internet: http:\\www.ambit.com.tw\
中華民國臺灣省新竹縣新竹科學園區新安路5號5樓之1
電話886-3-5784975，傳真：886-3-5782924
7. Then click ‘Finish’ to exit the InstallShield Wizard.
Ambit Microsystems Corporation國碁電子(股)公司
5F-1, 5 Hsin-An Rd., Hsinchu Science-Based Industrial Park, Hsinchu, Taiwan, R.O.C.
TEL: 886-3-5784975, FAX: 886-3-5782924, Internet: http:\\www.ambit.com.tw\
中華民國臺灣省新竹縣新竹科學園區新安路5號5樓之1
電話886-3-5784975，傳真：886-3-5782924
Section Three: Modem Installation
The following steps provide instructions for installing your 56K Internal modem.
1. Check the BT/modem Module already inserted into the slot.
2. Insert the connector of RJ-11 cable into the female connector of modem. The connector is keyed and will
no allow incorrect insertion. Plug the other end of the RJ-11 cable into an available phone jack.
3.1 Driver Installation
Your modem is using the Plug and Play (PnP) capabilities of you computer. PnP is a set of specifications that
define the ability for the computer hardware and operating system to automatically configure all compliant
devices that are installed, relieving the user of the need to determine which addresses and interrupts to user for
each device.
Proceed to the following section.
1. Start Windows 98, an “PCI Card” dialog with drive selected will appear. Click “Next”
2.
Search for the best driver for Modem card and click Next to continue.
Ambit Microsystems Corporation國碁電子(股)公司
5F-1, 5 Hsin-An Rd., Hsinchu Science-Based Industrial Park, Hsinchu, Taiwan, R.O.C.
TEL: 886-3-5784975, FAX: 886-3-5782924, Internet: http:\\www.ambit.com.tw\
中華民國臺灣省新竹縣新竹科學園區新安路5號5樓之1
電話886-3-5784975，傳真：886-3-5782924
3 Please release your driver to “c:\driver” or any specific location you want.
Ambit Microsystems Corporation國碁電子(股)公司
5F-1, 5 Hsin-An Rd., Hsinchu Science-Based Industrial Park, Hsinchu, Taiwan, R.O.C.
TEL: 886-3-5784975, FAX: 886-3-5782924, Internet: http:\\www.ambit.com.tw\
中華民國臺灣省新竹縣新竹科學園區新安路5號5樓之1
電話886-3-5784975，傳真：886-3-5782924
4. After Windows finishes loading, select My Computer\Control Panel\System\Device Manager. If you can
see the modem device on this Device Manager, then you already complete the Modem Driver installation.
Ambit Microsystems Corporation國碁電子(股)公司
5F-1, 5 Hsin-An Rd., Hsinchu Science-Based Industrial Park, Hsinchu, Taiwan, R.O.C.
TEL: 886-3-5784975, FAX: 886-3-5782924, Internet: http:\\www.ambit.com.tw\
中華民國臺灣省新竹縣新竹科學園區新安路5號5樓之1
電話886-3-5784975，傳真：886-3-5782924
3.2 AT Commands
Basic AT Commands
A summary of the commands implemented by the modem are shown in Table1. Commands may be executed
when the modem is in COMMAND mode. COMMAND mode is entered upon one of the following conditions:
After power up.
At the termination of a connection.
After the execution of a command other than dial or answer commands (ATO or AT&T).
Upon the receipt of the ESCAPE SEQUENCE (three consecutive characters matching the contents of S register 2)
while online mode.
Upon the on-to-off transition of DTR if D1, &D2, or &D3 has been set.
AT Commands
Basic AT Commands
Command
A/
B0
C1
Function
Re-execute command
Select V.22 connect @1200 bps
Return OK message
Command
B1
Dn
Function
Go off-hook and attempt to answer a call
Select Bell 212A connect @1200 bps
Dial modifier
Ambit Microsystems Corporation國碁電子(股)公司
5F-1, 5 Hsin-An Rd., Hsinchu Science-Based Industrial Park, Hsinchu, Taiwan, R.O.C.
TEL: 886-3-5784975, FAX: 886-3-5782924, Internet: http:\\www.ambit.com.tw\
中華民國臺灣省新竹縣新竹科學園區新安路5號5樓之1
電話886-3-5784975，傳真：886-3-5782924
E0
H0
I0
I1
I3
I4
I6
L1
L3
M1
N0
N1
Q1
Sn?
V0
W0
W2
X0
X2
X4
Z1
&C1
&D0
Turn off command echo
Initiate a hang-up sequence
Report product code
Report pre-computed checksum
Report firmware revision, model,
and interface type
Report response programmed by OEM
Report modem data pump model
and code revision
Set low speaker volume
Set high speaker volume
Turn speaker on during handshaking
and turn speaker off while receiving
carrier
Turn off auto mode detection
Turn on auto mode detection
Force pulse dialing
Inhibit result codes to DTE
Return the value of S-Register n
Force DTMF dialing
Report short form result codes
Report DTE speed only
Report DCE speed only
Report basic call progress result codes,
i.e., Ok, Connect, Ring, No Carrier
(also, for busy, if enabled, and dial tone
not detected), No Answer and Error
Report basic call progress result codes
and connections speeds, i.e., Ok,
Connect, Ring, No Carrier (also, for
busy, if enabled, and dial tone not
detected), No Answer, Connect XXXX,
and Error
Report all call progress result codes
and connections rate, i.e., Ok, Connect,
Ring, No Carrier, No Answer, Connect
XXXX, Busy, No Dial Tone and Error
Soft reset and restore stored profile 1
after warm reset
Allow RLSD to follow the carrier state
Interpret DTR On-to-OFF transition
per &Qn
E1
H1
I2
I5
I7
L0
L2
M0
M2
M3
Q0
Sn
Sn=v
V1
W1
Report long form result codes
Report line speed, EC protocol and DTE
speed
X1
Report basic call progress result codes
and connections speeds (Ok, Connect,
Ring, No Carrier (also, for busy, if
enabled, and dial tone not detected), No
Answer, Connect XXXX, and Error
X3
Report basic call progress result codes
and connections rate, i.e., Ok, Connect,
Ring, No Carrier, No Answer, Connect
XXXX, Busy, and Error
Y0
Disable long space disconnect before onhook
Z0
&C0
Restore stored profile 0 after warm reset
Soft reset and force RLSD active
regardless of the carrier state
&D1
Interpret DTR On-to-OFF transition
per &Qn
&Q0, &Q5, &Q6 The modem ignores DTR
&Q1, &Q4
The modem hangs up
&Q2, &Q3
The modem hangs up
&D2
Interpret DTR On-to-OFF transition
per &Qn
&Q0, &Q1, &Q4, &Q5, &Q6 Asynchronous escape
&Q2, &Q3
The modem hangs up
&D1
&Q0 through &Q6 The modem hangs up
&F0
&G0
&G2
Restore factory configuration 0
Disable guard tone
Enable 1800 Hz guard tone
&K0
Disable DTE/DCE flow control
Turn on command echo
If on-hook, go off-hook and enter
command mode
Report “OK” if the calculated checksum
equals the prestored checksum or if the
prestored checksum value is FFh
Report the country code parameter
Report the DAA code
Set low speaker volume
Set medium speaker volume
Turn speaker off
Turn speaker on during handshaking and
while receiving carrier
Turn speaker off during dialing and
receiving carrier and turn speaker on
during answering
Allow result codes to DTE
Select S-Register n as default
Set default S-Register n to value v
Interpret DTR On-to-OFF transition
per &Qn
&Q0, &Q1, &Q4, &Q5, &Q6 Soft reset
&Q2, &Q3
The modem hangs up
&G1
&J0
Disable guard tone
Set S-Register response only for compatibility
Ambit Microsystems Corporation國碁電子(股)公司
5F-1, 5 Hsin-An Rd., Hsinchu Science-Based Industrial Park, Hsinchu, Taiwan, R.O.C.
TEL: 886-3-5784975, FAX: 886-3-5782924, Internet: http:\\www.ambit.com.tw\
中華民國臺灣省新竹縣新竹科學園區新安路5號5樓之1
電話886-3-5784975，傳真：886-3-5782924
&K3
&K6
Enable RTS/CTS DTE/DCE flow
&K4
control
Enable both RTS/CTS and XON/XOFF&M0
flow control
&P0
&P1
Enable XON/XOFF DTE/DCE flow
control
Select direct asynchronous mode
Set 10 pps pulse dial with 39%/61%
make/break
Set 20 pps pulse dial with 39%/61%
make/break
Set 10 pps pulse dial with 33%/67%
&P2
make/break
&Q0
Select direct asynchronous mode
&Q5
Modem negotiates an error corrected &Q6
Select asynchronous operation in normal
link
mode
&R0
CTS tracks RTS (sync) or CTS is
&R1
CTS is always active (sync) or CTS is
normally ON and will turn OFF
normally ON and will turn OFF
only if required by flow control (async)
only if required by flow control (async)
&S0
DSR is always active
&S1
DSR will become active after answer
&T0
Terminate any test in progress
tone has been detected and inactive after
&T1
Initiate local analog loop back
the carrier has been lost
&T2
Returns ERROR result code
&T3
Initiate local digital loop back
&V
Display current configuration and
&W0
Store the current configuration as
stored profiles
profile 0
&Y0
Recall stored profile 0 upon power up
&Zn=x Store dial string x (up to 34 digits)
%E0
Disable line quality monitor and auto
to location n (0 to 3)
retrain
%E1
Enable line quality monitor and auto
%E2
Enable line quality monitor and fallback/
retrain
fall forward
When modem receives a break from the DTE:
\K0,2,4 Enter on-line command mode, no
\K1
Clear buffers and send break to remote
break sent to the remote modem
modem
\K3
Send break to remote modem
\K5
Send break to remote modem in sequence
immediately
with transmitted data
When modem receives \B in on-line command state:
\K0,1
Clear buffers and send break to remote \K2,3
Send break to remote modem immediately
modem
\K4,5
Send break to remote modem in sequence with transmitted data
When modem receives break from the remote modem:
\K0,1
Clear data buffers and send break to
\K2,3
DTE
\K4,5
\N0
\N2
\N4
\V0
+MS
+H1
+H3
**0
-SDR=0
Select normal speed buffered mode
\N1
Select reliable link mode
\N3
Force LAPM mode
\N5
Connect messages are controlled
\V1
by the command settings X, W, and S95
Select modulation
+H0
Enable RPI and set DTE speed to
19200 bps
+H2
Enable RPI and set DTE speed to
+H11
57600 bps
+H16
Download to flash memory at last
**1
sensed speed
**2
Disable distinctive ring
-SDR=1
Send a break immediately to DTE
Send a break with received data to the
DTE
Select direct mode
Select auto reliable mode
Force MNP mode
Connect messages are displayed in the
single line format
Disable Rockwell Protocol Interface (RPI)
/Video ready mode
Enable RPI and set DTE speed to 38400 bps
Enable RPI+ mode
Enable Video Ready mode
Download to flash memory at 38.4 kbps
Download to flash memory at 57.6 kbps
Enable distinctive ring type 1
Ambit Microsystems Corporation國碁電子(股)公司
5F-1, 5 Hsin-An Rd., Hsinchu Science-Based Industrial Park, Hsinchu, Taiwan, R.O.C.
TEL: 886-3-5784975, FAX: 886-3-5782924, Internet: http:\\www.ambit.com.tw\
中華民國臺灣省新竹縣新竹科學園區新安路5號5樓之1
電話886-3-5784975，傳真：886-3-5782924
-SDR=2
-SDR=4
-SDR=6
Enable distinctive ring type 2
Enable distinctive ring type 3
Enable distinctive ring type 2 and 3
-SDR=3
-SDR=5
-SDR=7
Enable distinctive ring type 1 and 2
Enable distinctive ring type 1 and 3
Enable distinctive ring type 1, 2 and 3
%C1
\A1
\A3
Enable MNP 5 data compression
Set maximum block size in MNP to 128
Set maximum block size in MNP to 256
ECC Commands
%C0
\A0
\A2
\Bn
Disable data compression
Set maximum block size in MNP to 64
Set maximum block size in MNP to 192
Send break of n x 100 ms
MNP 10 Commands
-K0
-K2
Disable MNP 10 extended services
-K1
Enable MNP 10 extended services
Disable MNP 10 extended services
-SEC=0 Disable MNP 10-EC
detection only
-SEC=1, [] Enable MNP 10-EC and set transmit level 0 to 30 (0 dBm to -30 dBm)
FAX Class 1
+Fclass=1 Service class
+FAE=1 Enable data/fax auto answer
+FRM=n Receive data
+FTH=n Transmit data with HDLC framing
+FTS=n Stop transmission and wait, nx10 ms
+FAE=0
+FRH=n
+FRS=n
+FTM=n
Disable data/fax auto answer
Receive data with HDLC framing
Receive silence, nx10 ms
Transmit data
V.92 Command set
1.AT%TT61 V.92 generate V.92 PCM upstream signal for PTT testing.
2.AT+PQC=255 to clear all stored fast connect profiles.
Ambit Microsystems Corporation國碁電子(股)公司
5F-1, 5 Hsin-An Rd., Hsinchu Science-Based Industrial Park, Hsinchu, Taiwan, R.O.C.
TEL: 886-3-5784975, FAX: 886-3-5782924, Internet: http:\\www.ambit.com.tw\
中華民國臺灣省新竹縣新竹科學園區新安路5號5樓之1
電話886-3-5784975，傳真：886-3-5782924
Ambit Microsystems Corporation國碁電子(股)公司
5F-1, 5 Hsin-An Rd., Hsinchu Science-Based Industrial Park, Hsinchu, Taiwan, R.O.C.
TEL: 886-3-5784975, FAX: 886-3-5782924, Internet: http:\\www.ambit.com.tw\
中華民國臺灣省新竹縣新竹科學園區新安路5號5樓之1
電話886-3-5784975，傳真：886-3-5782924
S-Registers
Register Function
Range/units
S0 Rings to auto-answer
0-255/rings
S1 Ring counter
0-255/rings
S2 Escape character
0-255/ASCII
S3 Carriage return character
0-127/ASCII
S4 Line feed character
0-127/ASCII
S5 Backspace character
0-255/ASCII
S6 Wait time for dial tone
2-255/s
S7 Wait time for carrier
1-255/s
S8 Pause time for dial delay modifier
0-255/s
S9 Carrier detect response time
1-255/.1 s
S10 Carrier loss disconnect time
1-255/.1 s
S11 DTMF tone duration
50-255/.001 s
S12 Escape prompt delay
0-255/.02 s
S14 General bit mapped options status
S16 Test mode bit mapped options status (&T)
S18 Test timer
0-255/s
S19 Auto Sync options
S20 Auto Sync HDLC address or BSC
0-255
Sync character
S21 V.24/general bit mapped options status
S22 Speaker/results bit mapped options status
S23 General bit mapped options status
S24 Sleep inactivity timer
0-255/s
S25 Delay to DTR off
0-255/s or .01s
S26 RTS-to-CTS delay
0-255/.01 s
S27 General bit mapped options status
S28 General bit mapped options status
S29 Flash dial modifier time
0-255/10 ms
S30 Disconnect inactivity timer
0-255/10 s
S31 General bit mapped options status
S32 XON character
0-255/ASCII
S33 XOFF character
0-255/ASCII
S36 LAPM failure control
S37 Line connection speed
S38 Delay before forced hang-up
0-255/s
S39 Flow control bit mapped options status
S40 General bit mapped options status
S41 General bit mapped options status
S46 Data compression control
S48 V.42 negotiation control
S82 LAPM break control
S86 Call failure reason code
0-255
S91 PSTN transmit attenuation level
0-15/dBm
S92 Fax transmit attenuation level
0-15/dBm
S95 Result code messages control
Default
43
13
10
50
20
95
50
8 (8h)
48 (30h)
112 (70h)
10
10 (Ah)
10 (country dependent)
10 (country dependent)
150
Ambit Microsystems Corporation國碁電子(股)公司
5F-1, 5 Hsin-An Rd., Hsinchu Science-Based Industrial Park, Hsinchu, Taiwan, R.O.C.
TEL: 886-3-5784975, FAX: 886-3-5782924, Internet: http:\\www.ambit.com.tw\
中華民國臺灣省新竹縣新竹科學園區新安路5號5樓之1
電話886-3-5784975，傳真：886-3-5782924
Ambit Microsystems Corporation國碁電子(股)公司
5F-1, 5 Hsin-An Rd., Hsinchu Science-Based Industrial Park, Hsinchu, Taiwan, R.O.C.
TEL: 886-3-5784975, FAX: 886-3-5782924, Internet: http:\\www.ambit.com.tw\
中華民國臺灣省新竹縣新竹科學園區新安路5號5樓之1
電話886-3-5784975，傳真：886-3-5782924
Result Code Summary
OK
RING
ERROR
NO DIAL TONE
NO ANSWER
CONNECT 2400
CONNECT 9600
CONNECT 12000
CONNECT 19200
CONNECT 57600
CONNECT 230400
CONNECT 1200TX/75RX
BLACKLISTED
DATA
CARRIER 1200/75
CARRIER 1200
CARRIER 4800
CARRIER 9600
CARRIER 14400
CARRIER 19200
CARRIER 24000
CARRIER 28800
CONNECT 21600
CONNECT 26400
COMPRESSION: CLASS 5
COMPRESSION: NONE
PROTOCOL: LAPM
CARRIER 33600
CONNECT 31200
CARRIER 34000
CARRIER 38000
CARRIER 42000
CARRIER 46000
CARRIER 50000
CARRIER 54000
CONNECT 32000
CONNECT 36000
CONNECT 40000
CONNECT 44000
CONNECT 48000
CONNECT 52000
CONNECT 56000
10
12
14
16
18
20
23
32
35
44
46
48
50
52
54
56
58
61
63
66
69
77
79
91
151
153
155
157
159
161
165
167
169
171
173
175
177
CONNECT
NO CARRIER
CONNECT 1200
BUSY
CONNECT 0600
CONNECT 4800
CONNECT 7200
CONNECT 14400
15
CONNECT 38400
17
CONNECT 115200
CONNECT 75TX/1200RX
DELAYED
FAX
CARRIER 300
CARRIER 75/1200
CARRIER 2400
CARRIER 7200
CARRIER 12000
CARRIER 16800
CARRIER 21600
CARRIER 26400
CONNECT 16800
CONNECT 24000
62
CONNECT 28800
64
COMPRESSION: V.42 bis
PROTOCOL: NONE
CARRIER 31200
CONNECT 33600
CARRIER 32000
CARRIER 36000
CARRIER 40000
CARRIER 44000
CARRIER 48000
CARRIER 52000
CARRIER 56000
CONNECT 34000
166
CONNECT 38000
168
CONNECT 42000
170
CONNECT 46000
172
CONNECT 50000
174
CONNECT 54000
176
+FCERROR
+F4
11
13
19
22
24
33
40
45
47
49
51
53
55
57
59
67
70
78
84
150
152
154
156
158
160
162
Ambit Microsystems Corporation國碁電子(股)公司
5F-1, 5 Hsin-An Rd., Hsinchu Science-Based Industrial Park, Hsinchu, Taiwan, R.O.C.
TEL: 886-3-5784975, FAX: 886-3-5782924, Internet: http:\\www.ambit.com.tw\
中華民國臺灣省新竹縣新竹科學園區新安路5號5樓之1
電話886-3-5784975，傳真：886-3-5782924
Section Four: FCC Notice
4.1 FCC Compliance
This Equipment complies with Part 68 of the FCC Rules. On this equipment is a label that contains, among other information,
the FCC registration number and Ringer Equivalence Number (REN) for this equipment. You must, upon request, provide
this information to your telephone company.
If your telephone equipment causes harm to the telephone network, the Telephone Company may discontinue your service
temporarily. If posible, they will be notify in advience. But if advance notice isn’t practical, you will notified as soon as
possible. You will be informed of your right to file a complaint with the FCC.
Your telephone company may make changes in its facilities, equipment, operations or procedures that could affect proper
operation of your equipment. If they do, you will be notified in advance to give you an opportunity you maintain
uninterrupted telephone service.
The FCC prohibits this equipment’s should fail to operate properly, disconnect the equipment from the phone line to
determine if it is causing the problem. If the problem is with the equipment, discontinue use and contact your dealer or
vendor.
4.2 FCC Class B Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on , the user is encouraged to try to correct the interference by one or more of the following measures:
l Reorient or relocate the receiving antenna
l increase the separation between the equipment and the receiver
l Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
l Consult the dealer or an experienced radio/TV technician for help
Notice: (1)Shielded cables, if any, must be used in order to comply with the emission limits. (2) Any change or
modification not expressly approved by the grantee of the equipment authorized could void the user authority to operate the
equipment.
Caution: Please make sure you already disconnect the phone cable before you want to touch or remove modem module.
Ambit Microsystems Corporation國碁電子(股)公司
5F-1, 5 Hsin-An Rd., Hsinchu Science-Based Industrial Park, Hsinchu, Taiwan, R.O.C.
TEL: 886-3-5784975, FAX: 886-3-5782924, Internet: http:\\www.ambit.com.tw\
中華民國臺灣省新竹縣新竹科學園區新安路5號5樓之1
電話886-3-5784975，傳真：886-3-5782924
Appendix
Ambit Microsystems Corporation國碁電子(股)公司
5F-1, 5 Hsin-An Rd., Hsinchu Science-Based Industrial Park, Hsinchu, Taiwan, R.O.C.
TEL: 886-3-5784975, FAX: 886-3-5782924, Internet: http:\\www.ambit.com.tw\
中華民國臺灣省新竹縣新竹科學園區新安路5號5樓之1
電話886-3-5784975，傳真：886-3-5782924
Ambit Microsystems Corporation國碁電子(股)公司
5F-1, 5 Hsin-An Rd., Hsinchu Science-Based Industrial Park, Hsinchu, Taiwan, R.O.C.
TEL: 886-3-5784975, FAX: 886-3-5782924, Internet: http:\\www.ambit.com.tw\
中華民國臺灣省新竹縣新竹科學園區新安路5號5樓之1
電話886-3-5784975，傳真：886-3-5782924
Ambit Microsystems Corporation國碁電子(股)公司
5F-1, 5 Hsin-An Rd., Hsinchu Science-Based Industrial Park, Hsinchu, Taiwan, R.O.C.
TEL: 886-3-5784975, FAX: 886-3-5782924, Internet: http:\\www.ambit.com.tw\
中華民國臺灣省新竹縣新竹科學園區新安路5號5樓之1
電話886-3-5784975，傳真：886-3-5782924

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 24
Creator                         : .穨.Microsoft Word
Create Date                     : 2004:01:16 14:17:11
Title                           : .穨.manuT60M665.PDF
Author                          : .穨.Daphne Liu
Producer                        : Acrobat PDFWriter 4.0 for Windows

EXIF Metadata provided by EXIF.tools