Wooyoung WTN-17WE2 LCD Monitor With TV Function User Manual WTN 17WE2 UsrMan
Wooyoung Co., Ltd. LCD Monitor With TV Function WTN 17WE2 UsrMan
Wooyoung >
Contents
- 1. User Manual 1 of 2
- 2. User Manual 2 of 2
User Manual 1 of 2
LCD TV
User’s Manual
MODEL : WTN-15B2, WTN-17WE2
ENGLI
ENGLISH
SH
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
WARNING : FCC Regulations state that any unauthorized
changes or modifications to this equipment not expressly
approved by the manufacturer could void the user’s
authority to operate this equipment.
U.S.A. ONLY
Note to CATV system installer : This reminder is provided to
call the CATV system installer’s attention to Article 820-40
of the National Electrical Code that provides guidelines for
proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the
building, as close to the point of cable entry as practical.
This product utilizes tin-lead solder, and fluorescent lamp
containing a small amount of mercury. Disposal of these
materials may be regulated due to environmental
considerations. For disposal or recycling information,
please contact your local authorities or the Electronic
Industries Alliance : www.eia.org
CAUTION : TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the user
to the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
1
IMPORTANT
INFORMATION
CAUTION : TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE COVER
(OR BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK,
DO NOT OPEN.
The exclamation point within a triangle is intended
to alert the user to the presence of important
operating and maintenance (servicing) instructions
in the literature accompanying the product.
SAFETY
PRECAUTIONS
This set has been designed and manufactured to
assure personal safety. Improper use can result in
electric shock or fire hazard. The safeguards
incorporated in this unit will protect you if you
observe the following procedures for installation,
use and servicing. This unit is fully transistorized
and does not contain any parts that can be
repaired by the user.
• Read instructions —All operating instructions
must be read and understood before the
product is operated.
• Keep this manual in a safe place —These safety
and operating instructions must be kept in a
safe place for future reference.
• Observe warnings —All warnings on the
product and in the instructions must be
observed closely.
• Follow instructions —All operating instructions
must be followed.
• Attachments —Do not use attachments not
recommended by the manufacturer. Use of
inadequate attachments can result in
accidents.
• Power source —This
product must operate on a
power source specified on
the specification label. If
you are not sure of the type
of power supply used in
your home, consult your
dealer or local power company. For units
designed to operate on batteries or another
power source, refer to the operating
instructions.
• Power cord protection —
The AC cords must be
routed properly to prevent
people from stepping on them or objects from
resting on them. Check the cords at the plugs
and product.
• Overloading —Do not
overload AC outlets or
extension cords.
Overloading can cause fire or electric shock.
• Entering of objects and
liquids —Never insert an
object into the product
through vents or openings.
High voltage flows in the
product, and inserting an
object can cause electric shock and/or short
internal parts. For the same reason, do not spill
water or liquid on the product.
• Servicing —Do not
attempt to service the
product yourself.
Removing covers can
expose you to high
voltage and other dangerous conditions.
Request a qualified service person to perform
servicing.
• Repair —If any of the
following conditions
occurs, unplug the AC cord
from the AC outlet, and
request a qualified service
person to perform repairs.
a. When the power cord or plug is damaged.
b. When a liquid was
spilled on the product or
when objects have
fallen into the product.
c. When the product has been
exposed to rain or water.
d. When the
product does not
operate properly
as described in
the operating
instructions. Do not touch the controls other
than those described in the operating
instructions. Improper adjustment of
controls not described in the instructions
can cause damage, which often requires
extensive adjustment work by a qualified
technician.
e. When the product has been dropped or
2
damaged.
f. When the product displays an abnormal
condition. Any noticeable abnormality in the
product indicates that the product needs
servicing.
• Replacement parts —In
case the product needs
replacement parts, make
sure that the service
person uses replacement
parts specified by the
manufacturer, or those
with the same characteristics and performance
as the original parts. Use of unauthorized parts
can result in fire, electric shock and/or other
danger.
• Safety checks —Upon completion of service or
repair work, request the service technician to
perform safety checks to ensure that the
product is in proper operating condition.
• Wall or ceiling mounting —When mounting the
product on a wall or ceiling, be sure to install
the product according to the method
recommended by the manufacturer.
• Polarization —The product may be equipped
with a polarized alternating current line plug (a
plug having one blade wider than the other).
This plug will fit into the AC outlet only one
way.
This is a safety feature. If you are unable to
insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail
to fit, contact your electrician to replace your
obsolete outlet. Do not defeat the safety
purpose of the polarized plug.
• Unplug the AC cord from the AC outlet before
installing the speakers.
• Cleaning—Unplug the
AC cord from the AC
outlet before cleaning
the product. Use a
damp cloth to clean the
product. Do not use
liquid cleaners or aerosol cleaners.
• Water and moisture—Do not use the product
near water, such as
bathtub, washbasin,
kitchen sink and laundry
tub, swimming pool and in
a wet basement.
• Stand—Do not place the
product on an unstable
cart, stand, tripod or
table. Placing the product
on an unstable base can
cause the product to fall,
resulting in serious personal injuries as well as
damage to the product. Use only a cart, stand,
tripod, bracket or table recommended by the
manufacturer or sold with the product. When
mounting the product on a wall, be sure to
follow the manufacturer’s instructions. Use only
the mounting hardware recommended by the
manufacturer.
• When relocating the
product placed on a cart,
it must be moved with
utmost care. Sudden
stops, excessively force
and uneven floor surface
can cause the product to fall from the cart.
• Ventilation—The vents
and other openings in the
cabinet are designed for
ventilation. Do not cover
or block these vents and
openings since insufficient
ventilation can cause overheating and/or
shorten the life of the product. Do not place
the product on a bed, sofa, rug or other similar
surface, since they can block ventilation
openings. This product is not designed for
built-in installation; do not place the product
in an enclosed place such as a bookcase or
rack, unless proper ventilation is provided or
the manufacturer’s instructions are followed.
• The LCD panel used in this product is made of
glass. Therefore, it can break when the product
is dropped or applied with impact. Be careful
not to be injured by broken glass pieces in case
the panel breaks.
• Heat sources—Keep the product away from
safety precautions
3
6(59,&('(37
$//6(765(&(,9(
2852.
6$)(7<&+(&.
safety precautions
heat sources such as
radiators, heaters, stoves
and other heat-
generating products
(including amplifiers).
• The LCD panel is a very high technology
product with 2,359,296 (15”)/ 2,949,120
(17”Wide) thin film transistors, giving you fine
picture details. Occasionally, a few non-active
pixels may appear on the screen as a fixed
point of blue, green or red. Please note that
this does not affect the performance of your
product.
• If an outside antenna is connected to the
television equipment, be sure the antenna
system is grounded so as to provide some
protection against voltage surges and built-up
static charges.
Section 810 of the National Electrical Code
provides information with respect to proper
grounding of the mast and supporting
structure, grounding of the lead-in wire to an
antenna discharge unit, size of grounding
conductors, location of antenna-discharge unit,
connection to grounding electrodes,and
requirements for the grounding electrode.
• For added protection for
this television equipment
during a lightning storm,
or when it is left
unattended and unused
for long periods of time,
unplug it from the wall
outlet and disconnect the antenna. This will
prevent damage to the equipment due to
lightning and power-line surges.
• An outside antenna system should not be
located in the vicinity of overhead power lines
or other electric light or power circuits, or
where it can fall into such power lines or
circuits. When installing an outside antenna
system, extreme care should be taken to keep
from touching such power lines or circuits as
contact with them might be fatal.
4
ANTENNA DISCHARGE UNIT
(NEC SECTION 810-20)
ANTENNA LEAD
IN WIRE
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250 PART H)
GROUND CLAMP
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
EXAMPLE OF ANTENNA
GROUNDING
NEC - NATIONAL ELECTRICAL CODE
5
1
2
5
6
9
11
16
18
29
31
IMPORTANT INFORMATION
SAFETY PRECAUTIONS
TABLE OF CONTENTS
FUNCTIONAL OVERVIEW
FRONT VIEW
REAR VIEW
REMOTE CONTROL
PREPARATION
CONNECTIONS
MAINS CONNECTION
ANTENNA CONNECTION
CONNECTING EXTERNAL EQUIPMENT
BASIC OPERATIONS
SWITCHING ON/OFF
TV/AV MODE SELECTION
VOLUME CONTROL
CHANNEL SELECTION
MENU ADJUSTMENT
CHANNEL ADJUSTMENT
PICTURE ADJUSTMENT
SOUND ADJUSTMENT
PC ADJUSTMENT
FUNCTIONS ADJUSTMENT
TROUBLESHOOTING GUIDE
SPECIFICATION
TABLE OF
CONTENTS
FUNCTIONAL
OVERVIEW
FRONT VIEW
6
POWER indicator
Remote
Sensor
WTN-17WE2
17”
WTN-15B2
15”
92/
&+
0(18
799,'(2
32:(5
Volume up/down buttons
Channel up/down buttons
MENU button
TV/VIDEO button
POWER button
REAR VIEW
7
3&$8',2
'&9
3&5*%
!
@
#
$ ^% & * (
!PC AUDIO input
@Power (DC 12V) input
#PC RGB input
$MONITOR OUTPUT
%DTV/DVD input
^Audio/Video input
&S-VIDEO input
*Headphone jack
*Antenna input
TV set can be watched most comfortably with changing the angle of
the LCD TV set. You can adjust the angle up to 5° forward,
horizontally 90° backward.
8
REMOTE CONTROL
32:(5
',63/$<
0(18
087(
799,'(2
076 &+
&+3,3 ,1387
326,7,21
6/((3
&$37,21
3&
&20321(17
3,&02'(
&+
&+
92/
92/
DISPLAY button
MENU button
Volume Up/Down button
MUTE button
PC input mode button
Number buttons
+100 button
PIP picture display button
POWER button
Channel Up/Down buttons
Picture mode selection button
CAPTION button
COMPONENT input mode button
Sleep timer setting button
PIP channel Up/Down buttons
PIP position selection button
PIP source (TV/VIDEO/S-
VIDEO) selection button
TV/VIDEO/S-VIDEO input mode
selection button
Sound mode (Mono/
Stereo/SAP) selection button
1) DISPLAY button displays the current channel number, broadcasting
sound mode (or external input mode) and time.
2)PIP button works only when main picture is PC mode or
COMPONENT input (480p, 720p, 1080i) mode.
3) SLEEP button allows you to set a time when the TV automatically
switches to standby: OFF ➔ 30 MINUTES ➔ 60 MINUTES ➔ 90
MINUTES ➔ 120 MINUTES
9
INSERTING BATTERIES INTO THE REMOTE CONTROLLER
To load the batteries, turn the remote controller over and open
the battery compartment.
Insert the batteries supplied (two 1.5V, type AAA).
Make sure that the polarity matches with the (+) and (-) marks
inside of the battery compartment.
To avoid damage from possible battery leakage, remove the batteries if
you do not plan to use the remote controller for an extended period of
time.
USING THE REMOTE CONTROL UNIT
Use the remote control unit by pointing it towards the remote
control sensor on the Display. Objects between the remote
control unit and the remote control sensor may prevent proper
operation.
CAUTIONS REGARDING REMOTE CONTROL UNIT
• Do not expose the remote control unit to shock. In
addition, do not expose the remote control unit to liquids,
and do not place in an area with high humidity.
• Do not install or place the remote control unit under direct
sunlight. The heat may cause deformation of the remote
control unit.
• The remote control unit may not work properly if the
remote control sensor on the Display is under direct
sunlight or strong lighting. In such cases, change the angle
of the lighting or the Display, or operate the remote control
unit closer to the remote control sensor.
PREPARATION
preparation
10
SUPPLIED ACCESSORIES
Make sure the following accessories are provided with the
product.
AAA Batteries
PC signal cable (D-sub 15pin)
32:(5
',63/$<
0(18
087(
799,'(2
076 &+
&+
3,3 ,1387
326,7,21
6/((3
&$37,21
3&
&20321(17
3,&02'(
&+
&+
92/
92/
Remote control unit
LCD TV
User’s Manual
MODEL : WTN-15B2, WTN-17WE2
ENGLI
ENGLISH
SH
Operation manual
AC Adaptor
PC Audio cable
AC cord
11
CONNECTIONS
MAINS CONNECTION
Plug the mains cable into the power socket with 100V - 240V
AC, 50/60Hz .
TO CABLE TV (CATV)
ANTENNA CONNECTION
• A 75-ohm coaxial cable connector is built into the set for
easy hookup.When connecting the 75- ohm coaxial cable to
the set,screw the 75-ohm cable to the ANT.terminal.
• Some cable TV companies offer “premium pay channels”.
Since the signals of these premium pay channels are
scrambled, a cable TV converter/descrambler is generally
provided to the subscriber by the cable TV company. This
converter/descrambler is necessary for normal viewing of
the scrambled channels. (Set your TV to channel 3 or 4,
typically one of these channels is used. If this is unknown,
consult your cable TV company.) For more specific
instructions on installing cable TV, consult your cable TV
company. One possible method of utilizing the
converter/descrambler provided by your cable TV company
is explained next page. Please note: An RF switch provided
with two inputs (A and B) is required (not supplied).
Incoming cable
RF Switch
Two-set signal
SPLITTER
Cable TV Converter/
Descrambler