Zalman Tech TNN400APF-V2 Power Supply User Manual TNN400APF V2 Spec

Zalman Tech Co., Ltd. Power Supply TNN400APF V2 Spec

Users Manual

User ManualTNN400APF-V2Zalman Tech Co., Ltd.Note: This equipment has been tested and found to comply with the limits for a Class B digitaldevice, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonableprotection against harmful interference in a residential installation. This equipment generates, usesand can radiate radio frequency energy and, if not installed and used in accordance with theinstructions, may cause harmful interference to radio communications. However, there is noguarantee that interference will not occur in a particular installation. If this equipment does causeharmful interference to radio or television reception, which can be determined by turning theequipment off and on, the user is encouraged to try to correct the interference by one or more ofthe following measures:◎ Reorient or relocate the receiving antenna.◎ Increase the separation between the equipment and receiver.◎ Connect the equipment into an outlet on a circuit different from that to which the receiver isconnected.◎ Consult the dealer or an experienced radio/TV technician for help.Modifications not expressly approved by the manufacturer could void the user's authority tooperated the equipment under FCC rules.
0A-5VDC ±10% 0.3AZALMAN SPECIFICATIONfactor switching Power Supply. Especially, It is applied to the line input capability, 2.1 AC INPUT LINE REQUIREMENTS+3.3VDC-12VDC+5VSB±5%Efficiency400. Watt max ContinuousForm-factor 1. INTRODUCTIONThe "TNN400APF-V2" is a Power Supply designed to be used "ATX/ATX12V" form factorThe scope of this document is limited to the requirements of "ATX/ATX12V" PC form±5%±5%MODEL NO: TNN400APF-V2 REV.0POWERVin FREQUENCYMINVin(230VAC)Vin(115VAC)NOM5 2. ELECTRICAL SPECIFICATIONVin(230VAC)9018047Vin(115VAC)ParameterVACrmsVACrmsAAHzUNIT115230MAXPAGE: 1/7Outputvoltage Requla-tion+12V2DC+5VDC±5%±5%+12V1DC ±5%2.5AMin load(Amps)27.0A0.8A2AMax load(Amps)1826.0A0APeak current(Amps)≥75% at Full load1 16 180Apersonal computers. 1.1 SCOPEDATE: 2004. 04. 3010.5A0.5AATX/ATX12V440. Watt max peakremote ON/OFF, cooling, standby voltage("VSB") and electrical characteristics.-1352656310
Amps+12V1DC 1.0-5VDC"+12.6 Volts-10---11.50.50.50.00.3--5VDC 0.0+12V2DC+5VSB10-5V ±10% -4.75 -5.00+5VDC+3.3VDC0.0-"-1.0-Load)-0.5"3.0"-1.0""--1.00.00.0-"0.3""16-+12.6 Volts+12V2DC 1.0-MAX4) It shall not exceed 17 seconds in duration at peak +12VDC output power, 234Watts.PEAK+5VSB1) Maximum continuous total DC output power shall not exceed 400Watts.±5% +5.00 Volts+4.752.2.2 DC output CURRENT+12.00+12V1DC+5VDC+12V2DC ±5%+11.4 +12.00±5% +11.4-12VDC ±10%+4.75 +5.00+3.3VDC +3.30-12.00-10.80+3.14±5%+5.25 Volts-13.20+5.25-5.25 VoltsVolts+3.47""(normal -5.0+5VSBMODEL NO: TNN400APF-V2 REV.0--12VDCZALMAN SPECIFICATION PAGE: 2/70.0DATE: 2004. 04. 30"--0.3Load)Range 21.00.5+3.3VDC-12VDC0.52) Maximum +5V and +3.3V output power shall not exceed 180Watts.Parameter+12V1DC Amps3) Maximum Peak Total DC output power shall not exceed 440Watts.5) Output voltage of +5VSB shall be maintained within the power shut down.-NOMMIN(high 7.018-18+5VDCRangeRange 1±5%UNITTEST POINT : OUTPUT CONNECTOR LOAD TERMINALS.Parameter MIN NOMRange MAX UNITVolts2.1.1 INRUSH CURRENT Max. inrush current shall not exceed 90A(Peak to Peak).2.2 DC OUTPUT REQUIREMENTS2.2.1 OUTPUT REQUIREMENTS
AC INPUT PSU LOAD±1.0% -120 mVp-p50 "-5VDC - 20MHz. a 0.1㎌ Ceramic capacitors at each output with measuring band width from DC toMAXNOR"-±1.0%+5VDC ±1.0%+12V1DC2.2.3 EFFICIENCY+12V2DC ±1.0% -50+3.3VDCAC GROUND. Load Slew Rate : 0.2A/㎲2.2.5 OUTPUT TRANSIENT RESPONESE & OVERSHOOT AT TURN ON/OFFMAX step -12VDC -5V0.1AAC NEUTRAL-12VDCAC LIVE+5VSB ±1.0%±1.0% -±1.0%-Parameter Range MIN. The measurements should be made by crossing a 10㎌ electrolytic capacitor andV returnVoltage range -SCOPE"1) The power supply at full load provide AC/DC conversion efficiency 75% minimum.Parameter +5VSB0.1A+5VDC +3.3VDC120502.2.4 OUTPUT RIPPLE/NOISEUNIT""-20010㎌V OUT 0.1㎌50 "±3% ±3%Shoot rangeDATE: 2004. 04. 30-9A 7.8A 8.1A 0.1A±10%±3% ±3% ±3%+12VPAGE: 3/7ZALMAN SPECIFICATION±10% ±10%MODEL NO: TNN400APF-V2 REV.0±10% ±10%
T2 T3ZALMAN SPECIFICATION* PW-OK sense level : 95% of nominal2.3.1 REMOTE ON/OFF CONTROLPAGE: 4/7MODEL NO: TNN400APF-V2 REV.0 DATE: 2004. 04. 302.3.2 POWER UP DELAYPS_ONPS_OFF an active-low, TTL-compatible signal("PS-ON"). The +5VSB is on whenever the AC power is present.DC Enable95%10%T4 . When PS-ON is pulled to TTL low, the DC outputs are to be enabled. . When PS-ON is pulled to TTL high or open circuited, the DC outputs are to be disabled. Turn ON/OFF delay ≥ 1000mS The power supply DC outputs (with the exception of +5VSB) shall be enabled withPWR-OK2.3 TIMING / HOUSE KEEPINGThe output voltages shall rise from <10% of nominal to within the regulation ranges specified in sec 2.2.1 within 2 to 30ms.
Max UnitMin157.0. Power Down Warning : T4>1ms2.4 OUTPUT PROTECTION2.4.1. OVER VOLTAGE PROTECTION15.6VV+5VDC 5.74 6.3+12VDC4.3. +12V2 : 19A~ at 12V2 at no loadZALMAN SPECIFICATION4.2+3.3VDC13.43.76MODEL NO: TNN400APF-V2 REV.0. Logic level Low : <0.4V 4mADATE: 2004. 04. 30. +5V : 29A~ Test Condition : Output Full Load. +3.3V : 30A~. +12V1 : 19A~ at 12V1 at no loadPAGE: 5/7VV*Change latch mode at above voltage in power supply unit.2.4.2. SHORT CIRCUIT PROTECTION. Shutdown or latch at short +3.3, +5V and +12V.. No damage in compenents, PCB trace connector at continous shout.. The maximum short circuit current shall not exceed 240VA.2.4.3. OVER POWER PROTECTION. Logic level High :Between 2.4VDC and 5VDC output while sourcing current, 200㎂. Signal Type : Open Collector +5VDC, TTL compatible.. POK Delay : 100mS<T3<500ms2.3.4 VOLTAGE HOLD-UP TIMEThe power supply shall maintain output regulation per section 2.2.1 despiteParametera loss of input power at the low-end nominal range at maximum continuousNomoutput load as specified in section 1.1 for a minimum 16ms.2.3.3 POWER GOOD SIGNAL, POK
Primary lot is output full load at 55℃ 24HR. Primary to Secondary : 500VDC 100㏁. Primary to FG : 500VDC 100㏁. UL19502.4.4 DC INPUT PROTECTION2.4.7. This power supply shall comply with the followings.On2.4.10. INSULATION VOLTAGE WITHSTAND. IEC950Output Status2.4.9. POWER SWITCH On/Off TEST. VDE 0871/6.78 Class B2.4.5. BURN-IN2.4.11. LEAKAGE CURRENT(IEC950). The Maximum Leakage Current Following The Frame / AC Sine ConductorPAGE: 6/7MODEL NO: TNN400APF-V2 REV.0ZALMAN SPECIFICATION Shall be 1.0mA Maximum at 220VAC Input2.4.6. MEAN TIME BETWEEN FAILURES. Operating Time 50,000HR at 25℃.OffLogic " High"DATE: 2004. 04. 30Logic " Low". CSA C22.2 NO220 & CSA Bulletin 1402C, Level3Control Signal. VDE 0806, EN60950 A3. Use proper fuse for DC input over current protection.. FCC Part 15 Sub Part B, Class B2.4.8. EMI
. Between Input and Output : 1500VAC 10mA 1min or 1800VAC 10mA 3sec. Storage : -20℃ ~ 85℃ 2.4.12. DIELECTRIC STRENGTH. Phase : 0 - 360˚. Between Input and FG : 1500VAC 10mA 1min or 1800VAC 10mA 3sec. Operating : 5℃ ~ 25℃2.4.13. TEMPRATURE RANGE. Polarity : +, -. Mode : Common, Normal2.4.14. HUMIDITY RANGE. Operating : 20% ~ 80%. Storage : 10% ~ 95%. The power Supply Must not generate Acoustic Noise in excess of 30dB at a2.4.15. VIBRATION TEST. Non Operation : Sweep Test. Frequency : 5 ⇒ 20 ⇒ 500 ⇒ 5Hz. Acceleration :0.02G2.4.16. ACOUSTIC NOISE. Airection : X, Y, Z. Period : 6 Minutes. Cycie : 10 Distance of 1 Meter from any Point on The requirments Surface.MODEL NO: TNN400APF-V2 REV.0 DATE: 2004. 04. 30ZALMAN SPECIFICATION PAGE: 7/72.4.18. AC LINE NOISE. The Power Supply Shall Operate Normally When AC Line Noise is Applied. Noise Crest Value : 1000VAC. Pulse Width : 1㎲. Time : 3Minutes

Navigation menu