ASRock H510 Pro BTC+ LGA 1200 Intel H510 for Cryptocurrency Mining (BTC) Intel Motherboard User Manual

Copyright Notice: Disclaimer

English 1 H510 Pro TC Motherboard Layout 4 7 8 13 2 16 18 14 15 22 24 AT XPWR2 5 A N I 1 HDLED R ESET PLED PWRBT N PANEL1 1 RoHS M 1 USB 3.1 Gen1 T: USB1 B: USB2 A T 1 A A A B B C C D E E Mining Port

Global

ASRock > H510 Pro BTC

Full PDF Document

If the viewer doesn’t load, open the file directly.

Extracted Text

Version 1.0 Published May 2021 Copyright�2021 ASRock INC. All rights reserved.
Copyright Notice:
No part of this documentation may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc.
Products and corporate names appearing in this documentation may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe.
Disclaimer:
Specifications and information contained in this documentation are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this documentation.
With respect to the contents of this documentation, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or fitness for a particular purpose.
In no event shall ASRock, its directors, officers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of profits, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the documentation or product.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
CALIFORNIA, USA ONLY
The Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance controlled in Perchlorate Best Management Practices (BMP) regulations passed by the California Legislature. When you discard the Lithium battery in California, USA, please follow the related regulations in advance. "Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/ perchlorate"
ASRock Website: http://www.asrock.com

AUSTRALIA ONLY
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage caused by our goods. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. If you require assistance please call ASRock Tel : +886-2-28965588 ext.123 (Standard International call charges apply)
The terms HDMI� and HDMI High-Definition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
INTEL END USER SOFTWARE LICENSE AGREEMENT IMPORTANT - READ BEFORE COPYING, INSTALLING OR USING.
LICENSE. Licensee has a license under Intel's copyrights to reproduce Intel's Software only in its unmodified and binary form, (with the accompanying documentation, the "Software") for Licensee's personal use only, and not commercial use, in connection with Intel-based products for which the Software has been provided, subject to the following conditions:
(a) Licensee may not disclose, distribute or transfer any part of the Software, and You agree to prevent unauthorized copying of the Software.
(b) Licensee may not reverse engineer, decompile, or disassemble the Software.
(c) Licensee may not sublicense the Software.
(d) The Software may contain the software and other intellectual property of third party suppliers, some of which may be identified in, and licensed in accordance with, an enclosed license.txt file or other text or file.
(e) Intel has no obligation to provide any support, technical assistance or updates for the Software.
OWNERSHIP OF SOFTWARE AND COPYRIGHTS. Title to all copies of the Software remains with Intel or its licensors or suppliers. The Software is copyrighted and protected by the laws of the United States and other countries, and international treaty provisions. Licensee may not remove any copyright notices from the Software. Except as otherwise expressly provided above, Intel grants no express or implied right under Intel patents, copyrights, trademarks, or other intellectual property rights. Transfer of the license terminates Licensee's right to use the Software.
DISCLAIMER OF WARRANTY. The Software is provided "AS IS" without warranty of any kind, EITHER EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
LIMITATION OF LIABILITY. NEITHER INTEL NOR ITS LICENSORS OR SUPPLIERS WILL BE LIABLE FOR ANY LOSS OF PROFITS, LOSS OF USE, INTERRUPTION OF BUSINESS, OR INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAG

ES OF ANY KIND WHETHER UNDER THIS AGREEMENT OR OTHERWISE, EVEN IF INTEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
LICENSE TO USE COMMENTS AND SUGGESTIONS. This Agreement does NOT obligate Licensee to provide Intel with comments or suggestions regarding the Software. However, if Licensee provides Intel with comments or suggestions for the modification, correction, improvement or enhancement of (a) the Software or (b) Intel products or processes that work with the Software, Licensee grants to Intel a non-exclusive, worldwide, perpetual, irrevocable, transferable, royalty-free license, with the right to sublicense, under Licensee's intellectual property rights, to incorporate or otherwise utilize those comments and suggestions.
TERMINATION OF THIS LICENSE. Intel or the sublicensor may terminate this license at any time if Licensee is in breach of any of its terms or conditions. Upon termination, Licensee will immediately destroy or return to Intel all copies of the Software.
THIRD PARTY BENEFICIARY. Intel is an intended beneficiary of the End User License Agreement and has the right to enforce all of its terms.
U.S. GOVERNMENT RESTRICTED RIGHTS. The Software is a commercial item (as defined in 48 C.F.R. 2.101) consisting of commercial computer software and commercial computer software documentation (as those terms are used in 48 C.F.R. 12.212), consistent with 48 C.F.R. 12.212 and 48 C.F.R 227.7202-1 through 227.7202-4. You will not provide the Software to the U.S. Government. Contractor or Manufacturer is Intel Corporation, 2200 Mission College Blvd., Santa Clara, CA 95054.
EXPORT LAWS. Licensee agrees that neither Licensee nor Licensee's subsidiaries will export/re-export the Software, directly or indirectly, to any country for which the U.S. Department of Commerce or any other agency or department of the U.S. Government or the foreign government from where it is shipping requires an export license, or other governmental approval, without first obtaining any such required license or approval. In the event the Software is exported from the U.S.A. or re-exported from a foreign destination by Licensee, Licensee will ensure that the distribution and export/re-export or import of the Software complies with all laws, regulations, orders, or other restrictions of the U.S. Export Administration Regulations and the appropriate foreign government.
APPLICABLE LAWS. This Agreement and any dispute arising out of or relating to it will be governed by the laws of the U.S.A. and Delaware, without regard to conflict of laws principles. The Parties to this Agreement exclude the application of the United Nations Convention on Contracts for the International Sale of Goods (1980). The state and federal courts sitting in Delaware, U.S.A. will have exclusive jurisdiction over any dispute arising out of or relating to this Agreement. The Parties consent to personal jurisdiction and venue in those courts. A Party that obtains a judgment against the other Party in the courts identified in this section may enforce that judgment in any court that has jurisdiction over the Parties.
Licensee's specific rights may vary from country to country.

Motherboard Layout
1 23

27

USB 2.0 T: USB1 B: USB2
PS2 Keyboard
/Mouse

CPU_FAN1

1 CLRMOS1

DDR4 (64 bit, 288-pin module)

ATX12V1

4 56
PWRBTN1 RSTBTN1 CHA_FAN1

H510 Pro BTC+
7

ATXPWR2

ATXPWR1

HDMI1

RJ-45 LAN

26

USB 3.1 Gen1 T: USB1 B: USB2
CHA_FAN3
A

PCIE1

25

CHA_FAN4

A

PCIE2

M2_1

8

A
USB_3_4

SPK_ PANEL1 PLED1

1 CHA_FAN2

1

1

PLED PWRBTN HDLED RESET

9
10 11 12

SATA3_1

13
Intel
H510

SPI_TPM_J1 1

M_PORT1

Mining Port

14 15

B

16

PWR_PCIE3

B

PCIE3

CHA_FAN5

Mining Port

H510 Pro BTC+

24

CHA_FAN6

C

PCIE4

PWR_PCIE4

Mining Port
17 C
18
Mining Port

BUZZER1

D

PCIE5

Mining Port
D 19

PWR_PCIE5

CHA_FAN7

20

21

ATXPWR3

RoHS

23

CHA_FAN8
E

CMOS Battery
PCIE6

Mining Port
E 22

PWR_PCIE6

1

English

No. Description 1 CPU Fan Connector (CPU_FAN1) 2 288-pin DDR4 DIMM Slot (DDR4) 3 Clear CMOS Jumper (CLRMOS1) 4 Chassis Fan Connector (CHA_FAN1) 5 Power Button (PWRBTN1) 6 Reset Button (RSTBTN1) 7 ATX Power Connector (ATXPWR2) 8 ATX Power Connector (ATXPWR1) 9 USB 2.0 Header (USB_3_4) 10 System Panel Header (PANEL1) 11 Power LED and Speaker Header (SPK_PLED1) 12 Chassis Fan Connector (CHA_FAN2) 13 SATA3 Connector (SATA3_1) 14 SPI TPM Header (SPI_TPM_J1) 15 Mining Port (M_Port1) 16 PCIe Power Connector (PWR_PCIE3) 17 Chassis Fan Connector (CHA_FAN5) 18 PCIe Power Connector (PWR_PCIE4) 19 PCIe Power Connector (PWR_PCIE5) 20 Chassis Fan Connector (CHA_FAN7) 21 ATX Power Connector (ATXPWR3) 22 PCIe Power Connector (PWR_PCIE6) 23 Chassis Fan Connector (CHA_FAN8) 24 Chassis Fan Connector (CHA_FAN6) 25 Chassis Fan Connector (CHA_FAN4) 26 Chassis Fan Connector (CHA_FAN3) 27 ATX 12V Power Connector (ATX12V1)
2

English

I/O Panel
1

H510 Pro BTC+
2

5

4

3

No. Description

No. Description

1 USB 2.0 Ports (USB_1_2)

4 HDMI Port

2 LAN RJ-45 Port*

5 PS/2 Mouse/Keyboard Port

3 USB 3.2 Gen1 Ports (USB3_1_2)

* There are two LEDs on each LAN port. Please refer to the table below for the LAN port LED indications.
ACT/LINK LED SPEED LED

LAN Port

Activity / Link LED

Status
Off Blinking On

Description
No Link Data Activity Link

Speed LED
Status Off Orange Green

Description
10Mbps connection 100Mbps connection 1Gbps connection

English

3

Chapter 1 Introduction
Thank you for purchasing ASRock H510 Pro BTC+ motherboard, a reliable motherboard produced under ASRock's consistently stringent quality control. It delivers excellent performance with robust design conforming to ASRock's commitment to quality and endurance.
Because the motherboard specifications and the BIOS software might be updated, the content of this documentation will be subject to change without notice. In case any modifications of this documentation occur, the updated version will be available on ASRock's website without further notice. If you require technical support related to this motherboard, please visit our website for specific information about the model you are using. You may find the latest VGA cards and CPU support list on ASRock's website as well. ASRock website http://www.asrock.com.
1.1 Package Contents
� ASRock H510 Pro BTC+ Motherboard � ASRock H510 Pro BTC+ Quick Installation Guide � ASRock H510 Pro BTC+ Support CD � 1 x Serial ATA (SATA) Data Cable (Optional) � 1 x Screw for M.2 Socket (Optional)
4

English

H510 Pro BTC+

1.2 Specifications

Platform

� Solid Capacitor design

CPU

� Supports 10th Gen Intel� CoreTM Processors and 11th Gen Intel� CoreTM Processors (LGA1200)
� Digi Power design � 4 Power Phase design � Supports Intel� Turbo Boost Max 3.0 Technology

Chipset

� Intel� H510

Memory

� 1 x DDR4 DIMM Slot
* 2GB DRAM per module is not supported. � Supports DDR4 3200/2933/2800/2666/2400/2133 non-ECC,
un-buffered memory * 11th Gen Intel� CoreTM (i9/i7/i5) support DDR4 up to 3200; CoreTM (i3), Pentium� and Celeron� support DDR4 up to 2666. * 10th Gen Intel� CoreTM (i9/i7) support DDR4 up to 2933; CoreTM (i5/i3), Pentium� and Celeron� support DDR4 up to 2666.
* Please refer to Memory Support List on ASRock's website for
more information. (http://www.asrock.com/) � Supports ECC UDIMM memory modules (operate in non-
ECC mode) � Max. capacity of system memory: 32GB � Supports Intel� Extreme Memory Profile (XMP) 2.0

Expansion Slot

� 6 x PCI Express 3.0 x16 Slots (PCIE1 at x16 / PCIE2~6 at x1) � 1 x Mining Port (M_Port1 at x1)*
* Support USB Type Riser kit

Graphics

� Intel� UHD Graphics Built-in Visuals and the VGA outputs can be supported only with processors which are GPU integrated.
� 11th Gen Intel� CoreTM Processors support Intel� Xe Graphics Architecture (Gen 12). 10th Gen Intel� CoreTM Processors support Gen 9 Graphics

English

5

� Supports HDMI 1.4 with max. resolution up to 4K x 2K (4096x2160) @ 30Hz
� Supports Auto Lip Sync, Deep Color (12bpc), xvYCC and HBR (High Bit Rate Audio) with HDMI 1.4 Port (Compliant HDMI monitor is required)
� Supports HDCP 2.3 with and HDMI 1.4 Port

LAN

� Gigabit LAN 10/100/1000 Mb/s � Giga PHY Intel� I219V � Supports Wake-On-LAN � Supports Lightning/ESD Protection � Supports Energy Efficient Ethernet 802.3az � Supports PXE

Rear Panel I/O

� 1 x PS/2 Mouse/Keyboard Port � 1 x HDMI Port � 2 x USB 2.0 Ports (Supports ESD Protection) � 2 x USB 3.2 Gen1 Ports (Supports ESD Protection) � 1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED
LED)

Storage

� 1 x SATA3 6.0 Gb/s Connector, supports NCQ, AHCI and Hot Plug
� 1 x M.2 Socket, supports M Key type 2260/2280/22110 M.2 SATA3 6.0 Gb/s module

Connector

� 1 x System Panel Header � 1 x SPI TPM Header � 1 x Power LED and Speaker Header � 1 x CPU Fan Connector (4-pin) * The CPU Fan Connector supports the CPU fan of maximum 1A (12W) fan power. � 8 x Chassis Fan Connectors (4-pin) * CHA_FAN3~CHA_FAN8 supports the chassis fan of maximum 2.5A (30W) fan power. * CPU_FAN1, CHA_FAN1 and CHA_FAN2 can adjust 4-pin fan speed.

English

6

H510 Pro BTC+

BIOS Feature
Hardware Monitor
OS
Certifications

� 3 x 24 pin ATX Power Connectors � 1 x 8 pin PCIe 12V Power Connector � 4 x 4 pin PCIe Power Connectors � 1 x USB 2.0 Header (Supports 2 USB 2.0 ports) (Supports
ESD Protection) � 1 x Power Button � 1 x Reset Button
� AMI UEFI Legal BIOS with multilingual GUI support � ACPI 6.0 Compliant wake up events � SMBIOS 2.7 Support � CPU Core/Cache, CPU GT, VCCSA, DRAM, VCCIO,
VCCIN AUX Voltage Multi-adjustment
� Fan Tachometer: CPU, Chassis Fans � Quiet Fan (Auto adjust chassis fan speed by CPU tempera-
ture): CPU, Chassis Fans � Fan Multi-Speed Control: CPU, Chassis Fans � Voltage monitoring: CPU Vcore, +12V, +5V, +3.3V
� Microsoft� Windows� 10 64-bit � Linux: Ubuntu 16.04 LTS / Fedora 25 * Linux O/S basic function support only, due to the compatibility of the Liunx system itself, there is no guarantee that all functions are supported.
� FCC, CE � ErP/EuP Ready (ErP/EuP ready power supply is required)

* For detailed product information, please visit our website: http://www.asrock.com
Please realize that there is a certain risk involved with overclocking, including adjusting the setting in the BIOS, applying Untied Overclocking Technology, or using third-party overclocking tools. Overclocking may affect your system's stability, or even cause damage to the components and devices of your system. It should be done at your own risk and expense. We are not responsible for possible damage caused by overclocking.
7

English

Chapter 2 Installation
Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it.
Pre-installation Precautions
Take note of the following precautions before you install motherboard components or change any motherboard settings. � Make sure to unplug the power cord before installing or removing the motherboard.
Failure to do so may cause physical injuries to you and damages to motherboard components. � In order to avoid damage from static electricity to the motherboard's components, NEVER place your motherboard directly on a carpet. Also remember to use a grounded wrist strap or touch a safety grounded object before you handle the components. � Hold components by the edges and do not touch the ICs. � Whenever you uninstall any components, place them on a grounded anti-static pad or in the bag that comes with the components. � When placing screws to secure the motherboard to the chassis, please do not overtighten the screws! Doing so may damage the motherboard.
8

English

H510 Pro BTC+
2.1 Installing the CPU
1. Before you insert the 1200-Pin CPU into the socket, please check if the PnP cap is on the socket, if the CPU surface is unclean, or if there are any bent pins in the socket. Do not force to insert the CPU into the socket if above situation is found. Otherwise, the CPU will be seriously damaged.
2. Unplug all power cables before installing the CPU.
1 A B
2
9

English

4

5 10

3

English

H510 Pro BTC+
Please save and replace the cover if the processor is removed. The cover must be placed if you wish to return the motherboard for after service.
11

English

2.2 Installing the CPU Fan and Heatsink

1
12

2
CPU_FAN

English

H510 Pro BTC+
2.3 Installing Memory Module (DIMM)
This motherboard provides one 288-pin DDR4 (Double Data Rate 4) DIMM slot.
It is not allowed to install a DDR, DDR2 or DDR3 memory module into a DDR4 slot; otherwise, this motherboard and DIMM may be damaged. The DIMM only fits in one correct orientation. It will cause permanent damage to the motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation.
13

English

1 2 3 14

English

H510 Pro BTC+
2.4 Expansion Slots (PCI Express Slots and Mining Ports)
There are 6 PCI Express slots and 1 Mining port on the motherboard.
Before installing an expansion card, please make sure that the power supply is switched off or the power cord is unplugged. Please read the documentation of the expansion card and make necessary hardware settings for the card before you start the installation.
PCIe slots: PCIE1 (PCIe 3.0 x16 slot) is used for PCI Express x16 lane width card. PCIE2/PCIE3/PCIE4/PCIE5/PCIE6 (PCIe 3.0 x16 slot) is used for PCI Express x1 lane width cards. Mining Port: M_Port1 is used for riser kit (at x1 mode).
15

English

2.5 Jumpers Setup
The illustration shows how jumpers are setup. When the jumper cap is placed on the pins, the jumper is "Short". If no jumper cap is placed on the pins, the jumper is "Open".

Clear CMOS Jumper (CLRMOS1) (see p.1, No. 3)

2-pin Jumper

CLRMOS1 allows you to clear the data in CMOS. To clear and reset the system parameters to default setup, please turn off the computer and unplug the power cord from the power supply. After waiting for 15 seconds, use a jumper cap to short the pins on CLRMOS1 for 5 seconds. However, please do not clear the CMOS right after you update the BIOS. If you need to clear the CMOS when you just finish updating the BIOS, you must boot up the system first, and then shut it down before you do the clear-CMOS action. Please be noted that the password, date, time, and user default profile will be cleared only if the CMOS battery is removed. Please remember toremove the jumper cap after clearing the CMOS.

English

16

H510 Pro BTC+

2.6 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage to the motherboard.

System Panel Header (9-pin PANEL1) (see p.1, No. 10)

GND PWRBTN#
PLEDPLED+

GND RESET# GND HDLEDHDLED+ 1

Connect the power button, reset button and system status indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables.

PWRBTN (Power Button): Connect to the power button on the chassis front panel. You may configure the way to turn off your system using the power button.
RESET (Reset Button): Connect to the reset button on the chassis front panel. Press the reset button to restart the computer if the computer freezes and fails to perform a normal restart.
PLED (System Power LED): Connect to the power status indicator on the chassis front panel. The LED is on when the system is operating. The LED keeps blinking when the system is in S1/S3 sleep state. The LED is off when the system is in S4 sleep state or powered off (S5).
HDLED (Hard Drive Activity LED): Connect to the hard drive activity LED on the chassis front panel. The LED is on when the hard drive is reading or writing data.
The front panel design may differ by chassis. A front panel module mainly consists of power button, reset button, power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this header, make sure the wire assignments and the pin assignments are matched correctly.

English

17

Power LED and Speaker Header (7-pin SPK_PLED1) (see p.1, No. 11)

SPEAKER DUMMY DUMMY +5V

PLEDPLED+ PLED+
1

Please connect the chassis power LED and the chassis speaker to this header.

Serial ATA3 Connector Right Angle: (SATA_1: see p.1, No. 13)

USB 2.0 Header (9-pin USB_3_4) (see p.1, No. 9)

DUMMY GND P+ P-
USB_PWR

GND P+ PUSB_PWR 1

This SATA3 connector supports SATA data cables for internal storage devices with up to 6.0 Gb/s data transfer rate.
There is one header on this motherboard. This USB 2.0 header can support two ports.

Chassis Fan Connectors (4-pin CHA_FAN1)

4 3 21

(see p.1, No. 4)

FAN_SPEED_CONTROL CHA_FAN_SPEED FAN_VOLTAGE GND

(4-pin CHA_FAN2) 1

2

(see p.1, No. 12)

3

4

GND FAN_VOLTAGE CHA_FAN_SPEED FAN_SPEED_CONTROL

Please connect fan cables to the fan connectors and match the black wire to the ground pin.

English

18

H510 Pro BTC+

(4-pin CHA_FAN3) (see p.1, No. 26) (4-pin CHA_FAN4) (see p.1, No. 25) (4-pin CHA_FAN5) (see p.1, No. 17) (4-pin CHA_FAN6) (see p.1, No. 24) (4-pin CHA_FAN7) (see p.1, No. 20) (4-pin CHA_FAN8) (see p.1, No. 23)

4 3 21
FAN_SPEED_CONTROL CHA_FAN_SPEED +12V GND

CPU Fan Connector (4-pin CPU_FAN1) (see p.1, No. 1)
ATX Power Connectors (24-pin ATXPWR1) (see p.1, No. 8) (24-pin ATXPWR2) (see p.1, No. 7) (24-pin ATXPWR3) (see p.1, No. 21)
ATX 12V Power Connector (8-pin ATX12V1) (see p.1, No. 27)

FAN_SPEED_CONTROL CPU_FAN_SPEED
+12V GND
1 2 34

This motherboard provides a 4-Pin CPU fan (Quiet Fan) connector. If you plan to connect a 3-Pin CPU fan, please connect it to Pin 1-3.

12

24

1

13

This motherboard provides three 24-pin ATX power connectors. To use a 20-pin ATX power supply, please plug it along Pin 1 and Pin 13.

5

1

This motherboard

provides a 8-pin ATX 12V

power connector. To use a

8

4

4-pin ATX power supply,

please plug it along Pin 1

and Pin 5.

English

19

PCIe Power Connectors (4-pin PCIE_PWR3) (see p.1, No. 16) (4-pin PCIE_PWR4) (see p.1, No. 18) (4-pin PCIE_PWR5) (see p.1, No. 19) (4-pin PCIE_PWR6) (see p.1, No. 22)

Please connect these connectors to the power supplies.
Important: Make sure the 4-pin PCIe power connector and the external power connector on the graphics card are connected to the same PSU; otherwise, the motherboard and the graphics card may be damaged.

Mining Port (M_Port1: see p.1, No. 15)

9 PERXN PERXP 8
GND 7 PETXP 6 PETXN 5

1 WAKE# 2 CLKN 3 CLKP 4 RST

Please connect this port to the riser kit. Note: DO NOT install USB device on Mining Port (M_Port1), it is designed for x1 USB riser kit only.

SPI TPM Header (13-pin SPI_TPM_J1) (see p.1, No. 14)

SPI_DQ3 SPI_PWR Dummy CLK SPI_MOSI RST# TPM_PIRQ
1
SPI_TPM_CS# GND RSMRST# SPI_MISO SPI_CS0 SPI_DQ2

This connector supports SPI Trusted Platform Module (TPM) system, which can securely store keys, digital certificates, passwords, and data. A TPM system also helps enhance network security, protects digital identities, and ensures platform integrity.

English

20

H510 Pro BTC+

2.7 Smart Switches
The motherboard has two smart switches: Power Button and Reset Button.

Power Button (PWRBTN1) (see p.1, No. 5)

Power Button allows users to quickly turn on/off the system.

Reset Button (RSTBTN1) (see p.1, No. 6)

Reset Button allows users to quickly reset the system.

English

21

2.8 M.2_SSD (NGFF) Module Installation Guide
The M.2, also known as the Next Generation Form Factor (NGFF), is a small size and versatile card edge connector that aims to replace mPCIe and mSATA. The M.2 Socket supports type 2260/2280/22110 M.2 SATA3 6.0 Gb/s module.
Installing the M.2_SSD (NGFF) Module
Step 1 Prepare a M.2_SSD (NGFF) module and the screw.

3 2 1

Step 2
Depending on the PCB type and length of your M.2_SSD (NGFF) module, find the corresponding nut location to be used.

C

B

A

No. Nut Location PCB Length Module Type

1 A 4.2cm Type 2242

2 B 6cm Type2260

3 C 8cm Type 2280

4 D 11cm Type 22110

English

22

D

C

B

A

D

C

B

A

D

C

B

A

H510 Pro BTC+
Step 3 Move the standoff based on the module type and length. The standoff is placed at the nut location C by default. Skip Step 3 and 4 and go straight to Step 5 if you are going to use the default nut. Otherwise, release the standoff by hand.
Step 4 Peel off the yellow protective film on the nut to be used. Hand tighten the standoff into the desired nut location on the motherboard.
Step 5 Gently insert the M.2 (NGFF) SSD module into the M.2 slot. Please be aware that the M.2 (NGFF) SSD module only fits in one orientation.

D

C

B

A

20o

English

23

D

C

NUT2

NUT1

Step 6
Tighten the screw with a screwdriver to secure the module into place. Please do not overtighten the screw as this might damage the module.

M.2_SSD (NGFF) Module Support List

Vendor ADATA Crucial EZLINK Intel Kingston Kingston LITEON PLEXTOR PLEXTOR SanDisk SanDisk SanDisk Transcend Transcend V-Color V-Color WD WD

Interface SATA SATA SATA SATA SATA SATA SATA SATA SATA SATA SATA SATA SATA SATA SATA SATA SATA SATA

P/N ADATA - AXNS381E-128GM-B Crucial-CT240M500SSD4-240GB EZLINK P51B-80-120GB INTEL 540S-SSDSCKKW240H6-240GB Kingston-RBU-SNS8400S3 / 180GD Kingston SM2280S3G2/120G - Win8.1 LITEON LJH-256V2G-256GB (2260) PLEXTOR PX-128M7VG-128GB PLEXTOR PX-128M6G-2260-128GB SanDisk-SD6SN1M-128G SanDisk X400-SD8SN8U-128G Sandisk Z400s-SD8SNAT-128G-1122 Transcend TS256GMTS800-256GB Transcend TS64GMTS400-64GB V-Color 120G V-Color 240G WD BLUE WDS100T1B0B-00AS40 WD GREEN WDS240G1G0B-00RC30

For the latest updates of M.2_SSD (NFGG) module support list, please visit our website for details: http://www.asrock.com

English

24

H510 Pro BTC+
2.9 Installing the 4-pin PCIe Power Connectors
The extra 4-pin PCIe power connectors on this motherboard offer more power for your graphics cards. They provide stable voltages and greatly reduce the risks of burning your motherboard or graphics cards. When the graphics cards are installed, be sure to install the PSU's 4-pin power cables to the corresponding 4-pin PCIe power connectors (PCIE_ PWR) on your motherboard; otherwise, the cards may be damaged.
Make sure the 4-pin PCIe power connector and the external power connector on the graphics card are connected to the same PSU; otherwise, the motherboard and the graphics card may be damaged.
25

English

2.10 Special Features 2.10.1 Smart PCIe State Detection
This motherboard has included a smart way to show the status of every graphics card. While the system is booting, the Power-On, Self-Test (POST) screen will show the status of the graphics cards that were installed on the motherboard.
26

English

H510 Pro BTC+

2.10.2 Graphics Card Indicator LED
ASRock also placed a faulty graphics card indicator LED behind every mining ports and PCIe slots so you may monitor the status even without a screen.

USB 2.0 T: USB1 B: USB2
PS2 Keyboard
/Mouse

CPU_FAN1

1 CLRMOS1

DDR4 (64 bit, 288-pin module)

ATX12V1

PWRBTN1 RSTBTN1 CHA_FAN1

ATXPWR2

ATXPWR1

HDMI1

RJ-45 LAN

USB 3.1 Gen1 T: USB1 B: USB2
CHA_FAN3
A

PCIE1

CHA_FAN4
A

PCIE2

B

PCIE3

CHA_FAN6
C

H510 Pro BTC+
PCIE4

D
CHA_FAN8
E

BUZZER1
PCIE5 RoHS
CMOS Battery
PCIE6

M2_1

PLED PWRBTN HDLED RESET

A
USB_3_4

SPK_ PANEL1 PLED1

1 CHA_FAN2

1

1

SATA3_1

Intel H510

SPI_TPM_J1 1

M_PORT1

Mining Port

B

PWR_PCIE3

CHA_FAN5

Mining Port Mining Port
C

PWR_PCIE4

CHA_FAN7

Mining Port
Mining Port
D

PWR_PCIE5

ATXPWR3

Mining Port
E

PWR_PCIE6

Graphics Card Indicator LED 27

English

1 Einleitung
Vielen Dank, dass Sie sich f�r das H510 Pro BTC+ von ASRock entschieden haben � ein zuverl�ssiges Motherboard, das konsequent unter der strengen Qualit�tskontrolle von ASRock hergestellt wurde. Es liefert ausgezeichnete Leistung mit robustem Design, das ASRock Streben nach Qualit�t und Best�ndigkeit erf�llt.
Da die technischen Daten des Motherboards sowie die BIOS-Software aktualisiert werden k�nnen, kann der Inhalt dieser Dokumentation ohne Ank�ndigung ge�ndert werden. Falls diese Dokumentation irgendwelchen �nderungen unterliegt, wird die aktualisierte Version ohne weitere Hinweise auf der ASRock-Webseite zur Verf�gung gestellt. Sollten Sie technische Hilfe in Bezug auf dieses Motherboard ben�tigen, erhalten Sie auf unserer Webseite spezifischen Informationen �ber das von Ihnen verwendete Modell. Auch finden Sie eine aktuelle Liste unterst�tzter VGA-Karten und Prozessoren auf der ASRock-Webseite. ASRock-Webseite http://www.asrock.com.
1.1 Lieferumfang
� ASRock H510 Pro BTC+-Motherboard � ASRock H510 Pro BTC+-Schnellinstallationsanleitung � ASRock H510 Pro BTC+-Support-CD � 1 x Serial-ATA- (SATA) Datenkabel (optional) � 1 x Schraube f�r M.2-Sockel (optional)
28

Deutsch

H510 Pro BTC+

1.2 Technische Daten

Plattform

� Feststoffkondensator-Design

Prozessor

� Unterst�tzt Intel� CoreTM-Prozessoren der 10. Generation und Intel� CoreTM-Prozessoren der 11. Generation (LGA1200)
� Digi Power design � 4-Leistungsphasendesign � Unterst�tzt Intel� Turbo Boost Max Technology 3.0

Chipsatz

� Intel� H510

Speicher

� 1 x DDR4-DIMM-Steckplatz
* 2 GB DRAM pro Modul werden nicht unterst�tzt. � Unterst�tzt ungepufferten DDR4-3200/2933/2800/2666/2400/2133-
Non-ECC-Speicher* * 11. Generation Intel� CoreTM (i9/i7/i5) unterst�tzen DDR4 bis 3200; CoreTM (i3), Pentium� und Celeron� unterst�tzen DDR4 bis 2666. 10. Generation Intel� CoreTM (i9/i7) unterst�tzen DDR4 bis 2933; CoreTM (i5/i3), Pentium� und Celeron� unterst�tzen DDR4 bis 2666.
* Weitere Informationen finden Sie in der Speicherkompatibilit�tsliste
auf der ASRock-Webseite. (http://www.asrock.com/) � Unterst�tzt ECC-UDIMM-Speichermodule (Betrieb im non-ECC-
Modus) � Systemspeicher, max. Kapazit�t: 32 GB � Unterst�tzt Intel� Extreme Memory Profile (XMP) 2.0

Erweiterungssteckplatz

� 6 x PCI-Express 3.0-x16-Steckpl�tze (PCIE1 bei x16 / PCIE2~6 bei x1)
� 1 x Mining-Port (M_Port1 bei x1)* * Unterst�tzt USB-Riser-Kit

Grafikkarte

� Integrierte Intel� UHD Graphics-Visualisierung und VGAAusg�nge k�nnen nur mit Prozessoren unterst�tzt werden, die GPU-integriert sind.
� 11. Generation Intel� CoreTM-Prozessoren unterst�tzen Intel� Xe Graphics Architecture (Gen. 12). 10. Generation Intel� CoreTMProzessoren unterst�tzen Gen 9 Graphics

Deutsch

29

� Unterst�tzt HDMI 1,4 mit maximaler Aufl�sung von 4K x 2K (4096 x 2160) bei 30Hz
� Unterst�tzt Auto-Lippensynchronizit�t, hohe Farbtiefe (12 bpc), xvYCC und HBR (Audio mit hoher Bitrate) mit HDMI 1.4-Port (konformer HDMI-Monitor erforderlich)
� Unterst�tzt HDCP 2.3 mit HDMI 1.4-Port

LAN

� Gigabit LAN 10/100/1000 Mb/s � Giga PHY Intel� I219V � Unterst�tzt Wake-On-LAN � Unterst�tzt Schutz gegen Blitzschlag/elektrostatische Entladung � Unterst�tzt energieeffizientes Ethernet 802.3az � Unterst�tzt PXE

R�ckblende, E/A
Speicher

� 1 x PS/2-Maus-/Tastaturanschluss � 1 x HDMI-Port � 2 x USB-2.0-Ports (unterst�tzt Schutz gegen elektrostatische
Entladung) � 2 x USB-3.2-Gen1-Ports (unterst�tzt Schutz gegen elektrostatische
Entladung) � 1 x RJ-45-LAN-Port mit LED (Aktivit�t/Verbindung-LED und
Geschwindigkeit-LED)
� 1 x SATA-III-6,0-Gb/s-Anschluss, unterst�tzt NCQ, AHCI und Hot-Plugging
� 1 x M.2-Sockel, unterst�tzt M-Key-2260/2280/22110-M.2-SATAIII-6,0-Gb/s-Modul

Anschluss

� 1 x Systemblendenstiftleiste � 1 x SPI-TPM-Stiftleiste � 1 x Betrieb-LED- und Lautsprecher-Stiftleiste � 1 x CPU-L�fteranschluss (4-polig) * Der CPU-L�fteranschluss unterst�tzt einen CPU-L�fter mit einer maximalen L�fterleistung von 1 A (12 W). � 8 x Geh�usel�fteranschl�sse (4-polig) * CHA_FAN3~CHA_FAN8 unterst�tzen einen Geh�usel�fter mit einer maximalen L�fterleistung von 2,5A (30 W). * CPU_FAN1, CHA_FAN1 und CHA_FAN2 k�nnen Geschwindigkeit des 4-poligen L�fters anpassen. � 3 x 24-poliger ATX-Netzanschl�sse

Deutsch

30

H510 Pro BTC+

� 1 x 8-poliger PCIe-12-V-Netzanschluss � 4 x 4-poliger PCIe-Netzanschl�sse � 1 x USB 2.0-Stiftleiste (unterst�tzt zwei USB 2.0-Ports) (unterst�tzt
Schutz gegen elektrostatische Entladung) � 1 x Ein-/Austaste � 1 x Reset-Taste

BIOS-Funktion

� AMI-UEFI-Legal-BIOS mit Unterst�tzung mehrsprachiger grafi-
scher Benutzerschnittstellen � ACPI 6.0-konforme Aufweckereignisse � SMBIOS 2.7-Unterst�tzung � CPU-Kern/Cache, CPU GT, VCCSA, DRAM, VCCIO, VCCIN
AUX-Mehrfachspannungsanpassung

Hardware�berwachung

� L�ftertachometer: CPU, Geh�usel�fter � Lautloser L�fter (automatische Anpassung der Geh�usel�fterge-
schwindigkeit durch CPU-Temperatur): CPU, Geh�usel�fter � Mehrfachgeschwindigkeitssteuerung: CPU, Geh�usel�fter � Spannungs�berwachung: CPU Vcore, +12V, +5V, +3,3V

Betriebssystem

� Microsoft� Windows� 10, 64 Bit � Linux: Ubuntu 16.04 LTS / Fedora 25 * Unterst�tzt nur Linux-OS-Basisfunktion aufgrund der Kompatibilit�t mit dem Linux-System selbst. Es wird nicht garantiert, dass alle Funktionen unterst�tzt werden.

Zertifizierun- � FCC, CE

gen

� ErP/EuP ready (ErP/EuP ready-Netzteil erforderlich)

* Detaillierte Produktinformationen finden Sie auf unserer Webseite: http://www.asrock.com
Bitte beachten Sie, dass mit einer �bertaktung, zu der die Anpassung von BIOS-Einstellungen, die Anwendung der Untied Overclocking Technology oder die Nutzung von �bertaktungswerkzeugen von Drittanbietern z�hlen, bestimmte Risiken verbunden sind. Eine �bertaktung kann sich auf die Stabilit�t Ihres Systems auswirken und sogar Komponenten und Ger�te Ihres Systems besch�digen. Sie sollte auf eigene Gefahr und eigene Kosten durchgef�hrt werden. Wir �bernehmen keine Verantwortung f�r m�gliche Sch�den, die durch eine �bertaktung verursacht wurden.
31

Deutsch

1.3 Jumpereinstellung
Die Abbildung zeigt, wie die Jumper eingestellt werden. Wenn die Jumper-Kappe auf den Kontakten angebracht ist, ist der Jumper ,,kurzgeschlossen". Wenn keine Jumper-Kappe auf den Kontakten angebracht ist, ist der Jumper ,,offen".

CMOS-l�schen-Jumper (CLRMOS1) (siehe S. 1, Nr. 3)

2-poliger Jumper

CLRMOS1 erm�glicht Ihnen die L�schung der Daten im CMOS. Zum L�schen und R�cksetzen der Systemparameter auf die Standardeinrichtung schalten Sie den Computer bitte ab und ziehen das Netzkabel aus der Steckdose. Warten Sie 15 Sekunde, schlie�en Sie dann die Kontakte an CLRMOS1 5 Sekunden lang mit einer Jumper-Kappe kurz. L�schen Sie den CMOS jedoch nicht direkt nach der BIOS-Aktualisierung. Falls Sie den CMOS direkt nach Abschluss der BIOS-Aktualisierung l�schen m�ssen, starten Sie das System zun�chst; fahren Sie es dann vor der CMOS-L�schung herunter. Bitte beachten Sie, dass Kennwort, Datum, Zeit und Benutzerstandardprofil nur gel�scht werden, wenn die CMOS-Batterie entfernt wird. Bitte denken Sie daran, die Jumper-Kappe nach der CMOSL�schung zu entfernen.

Deutsch

32

H510 Pro BTC+

1.4 Integrierte Stiftleisten und Anschl�sse
Integrierte Stiftleisten und Anschl�sse sind KEINE Jumper. Bringen Sie KEINE Jumper-Kappen an diesen Stiftleisten und Anschl�ssen an. Durch Anbringen von Jumper-Kappen an diesen Stiftleisten und Anschl�ssen k�nnen Sie das Motherboard dauerhaft besch�digen.

Systemblende-Stiftleiste (9-polig, PANEL1) (siehe S. 1, Nr. 10)

GND PWRBTN#
PLEDPLED+

GND RESET# GND HDLEDHDLED+ 1

Verbinden Sie Ein-/ Austaste, Reset-Taste und Systemstatusanzeige am Geh�use entsprechend der nachstehenden Pinbelegung mit dieser Stiftleiste. Beachten Sie vor Anschlie�en der Kabel die positiven und negativen Kontakte.

PWRBTN (Ein-/Austaste): Mit der Ein-/Austaste an der Frontblende des Geh�uses verbinden. Sie k�nnen die Abschaltung Ihres Systems �ber die Ein-/Austaste konfigurieren.
RESET (Reset-Taste): Mit der Reset-Taste an der Frontblende des Geh�uses verbinden. Starten Sie den Computer �ber die Reset-Taste neu, wenn er abst�rzt oder sich nicht normal neu starten l�sst.
PLED (Systembetriebs-LED): Mit der Betriebsstatusanzeige an der Frontblende des Geh�uses verbinden. Die LED leuchtet, wenn das System l�uft. Die LED blinkt, wenn sich das System im S1/S3-Ruhezustand befindet. Die LED ist aus, wenn sich das System im S4-Ruhezustand befindet oder ausgeschaltet ist (S5).
HDLED (Festplattenaktivit�ts-LED): Mit der Festplattenaktivit�ts-LED an der Frontblende des Geh�uses verbinden. Die LED leuchtet, wenn die Festplatte Daten liest oder schreibt.
Das Design der Frontblende kann je nach Geh�use variieren. Ein Frontblendenmodul besteht haupts�chlich aus Ein-/Austaste, Reset-Taste, Betrieb-LED, Festplattenaktivit�t-LED, Lautsprecher etc. Stellen Sie beim Anschlie�en Ihres Frontblendenmoduls an diese Stiftleiste sicher, dass Kabel- und Pinbelegung richtig abgestimmt sind.

Deutsch

33

Betrieb-LED- und Lautsprecher-Stiftleiste (7-polig, SPK_PLED1) (siehe S. 1, Nr. 11)

SPEAKER DUMMY DUMMY +5V

PLEDPLED+ PLED+
1

Bitte verbinden Sie die Betrieb-LED des Geh�uses und den Geh�uselautsprecher mit dieser Stiftleiste.

Serial-ATA-III-Anschluss Winkel rechts: (SATA_1: siehe S. 1, Nr. 13)

Dieser SATA-III-Anschluss nimmt SATA-Datenkabel zum Anschluss interner Speicherger�te mit einer Daten�bertragungsgeschwindigkeit bis 6,0 Gb/s auf.

USB 2.0-Stiftleiste (9-polig, USB_3_4) (siehe S. 1, Nr. 9)

DUMMY GND P+ P-
USB_PWR

GND P+ PUSB_PWR 1

Es gibt eine Stiftleiste an diesem Motherboard. Diese USB 2.0-Stiftleiste unterst�tzt zwei Ports.

Geh�usel�fteranschl�sse (4-polig, CHA_FAN1) (siehe S. 1, Nr. 4)

4 3 21
FAN_SPEED_CONTROL CHA_FAN_SPEED FAN_VOLTAGE GND

Bitte verbinden Sie die L�fterkabel mit den L�fteranschl�ssen; der schwarze Draht geh�rt zum Erdungskontakt.

(4-polig, CHA_FAN2) (siehe S. 1, Nr. 12)

1

GND

2

FAN_VOLTAGE

3

CHA_FAN_SPEED

4

FAN_SPEED_CONTROL

Deutsch

34

H510 Pro BTC+

(4-polig, CHA_FAN3) (siehe S. 1, Nr. 26) (4-polig, CHA_FAN4) (siehe S. 1, Nr. 25) (4-polig, CHA_FAN5) (siehe S. 1, Nr. 17) (4-polig, CHA_FAN6) (siehe S. 1, Nr. 24) (4-polig, CHA_FAN7) (siehe S. 1, Nr. 20) (4-polig, CHA_FAN8) (siehe S. 1, Nr. 23)

4 3 21
FAN_SPEED_CONTROL CHA_FAN_SPEED +12V GND

CPU-L�fteranschluss (4-polig, CPU_FAN1) (siehe S. 1, Nr. 1)
ATX-Netzanschl�sse (24-polig, ATXPWR1) (siehe S. 1, Nr. 8) (24-polig, ATXPWR2) (siehe S. 1, Nr. 7) (24-polig, ATXPWR3) (siehe S. 1, Nr. 21)
ATX-12-V-Netzanschluss (8-polig, ATX12V1) (siehe S. 1, Nr. 27)

FAN_SPEED_CONTROL CPU_FAN_SPEED
+12V GND
1 2 34

Dieses Motherboard bietet einen 4-poligen CPU-L�fteranschluss (lautloser L�fter). Falls Sie einen 3-poligen CPU-L�fter anschlie�en m�chten, verbinden Sie ihn bitte mit Kontakt 1 bis 3.

12

24

1

13

Dieses Motherboard bietet drei 24-polige ATX-Netzanschl�sse. Bitte schlie�en Sie es zur Nutzung eines 20-poligen ATX-Netzteils entlang Kontakt 1 und Kontakt 13 an.

5

1

Dieses Motherboard bietet einen

8-poligen ATX-12-V-Netzan-

schluss. Bitte schlie�en Sie es

zur Nutzung eines 4-poligen

8

4

ATX-Netzteils entlang Kontakt 1

und Kontakt 5 an.

Deutsch

35

PCIe-Netzanschl�sse (4-polig, PCIE_PWR3) (siehe S. 1, Nr. 16) (4-polig, PCIE_PWR4) (siehe S. 1, Nr. 18) (4-polig, PCIE_PWR5) (siehe S. 1, Nr. 19) (4-polig, PCIE_PWR6) (siehe S. 1, Nr. 22)

Bitte verbinden Sie diese Anschl�sse mit den Netzteilen.
Wichtig: Stellen Sie sicher, dass der 4-polige Stromanschluss und der externe Stromanschluss an der Grafikkarte mit demselben Netzteil verbunden sind; andernfalls k�nnten Motherboard un Grafikkarte besch�digt werden.

Mining-Port (M_Port1:siehe S. 1, Nr. 15)

Bitte verbinden Sie diesen Anschluss mit dem Riser-Set.

9 PERXN PERXP 8
GND 7 PETXP 6 PETXN 5

1 WAKE# 2 CLKN 3 CLKP 4 RST

SPI-TPM-Stiftleiste (13-polig, SPI_TPM_J1) (siehe S. 1, Nr. 14)

SPI_DQ3 +3.3V Dummy CLK SPI_MOSI RST# TPM_PIRQ
1
SPI_TPM_CS# GND RSMRST# SPI_MISO SPI_CS0 SPI_DQ2

Dieser Anschluss unterst�tzt das SPI Trusted Platform Module- (TPM) System, das Schl�ssel, digitale Zertifikate, Kennw�rter und Daten sicher aufbewahren kann. Ein TPMSystem hilft zudem bei der St�rkung der Netzwerksicherheit, sch�tzt digitale Identit�ten und gew�hrleistet die Plattformintegrit�t.

Deutsch

36

H510 Pro BTC+

1.5 Intelligente Schalter
Das Motherboard hat zwei intelligente Schalter: Ein-/Austaste und Reset-Taste.

Ein-/Austaste (PWRBTN1) (siehe S. 1, Nr. 5)

Mit der Ein-/Austaste kann der Benutzer das System schnell ein-/ abschalten.

Reset-Taste (RSTBTN1) (siehe S. 1, Nr. 6)

Der Reset-Taste erm�glicht das schnelle R�cksetzen des Systems.

Deutsch

37

1 Introduction
Nous vous remercions d'avoir achet� cette carte m�re ASRock H510 Pro BTC+, une carte m�re fiable fabriqu�e conform�ment au contr�le de qualit� rigoureux et constant appliqu� par ASRock. Fid�le � son engagement de qualit� et de durabilit�, ASRock vous garantit une carte m�re de conception robuste aux performances �lev�es.
Les sp�cifications de la carte m�re et du logiciel BIOS pouvant �tre mises � jour, le contenu de ce document est soumis � modification sans pr�avis. En cas de modifications du pr�sent document, la version mise � jour sera disponible sur le site Internet ASRock sans notification pr�alable. Si vous avez besoin d'une assistance technique pour votre carte m�re, veuillez visiter notre site Internet pour plus de d�tails sur le mod�le que vous utilisez. La liste la plus r�cente des cartes VGA et des processeurs pris en charge est �galement disponible sur le site Internet de ASRock. Site Internet ASRock http://www.asrock.com.
1.1 Contenu de l'emballage
� Carte m�re ASRock H510 Pro BTC+ � Guide d'installation rapide ASRock H510 Pro BTC+ � CD d'assistance ASRock H510 Pro BTC+ � 1 x c�ble de donn�es Serial ATA (SATA) (Optionnel) � 1 x vis pour socket M.2 (Optionnel)
38

Fran�ais

H510 Pro BTC+

1.2 Sp�cifications

Plateforme � Conception � condensateurs solides

Processeur

� Prend en charge les processeurs Intel� CoreTM 10�me G�n et les processeurs Intel� CoreTM 11�me G�n (LGA1200)
� Digi Power design � Alimentation � 4 phases � Prend en charge la technologie Intel� Turbo Boost Max 3.0

Chipset

� Intel� H510

M�moire
Fente d'expansion

� 1 x fente DIMM DDR4 * 2 Go de DRAM par module ne sont pas pris en charge. � Prend en charge les m�moires sans tampon non ECC DDR4
3200/2933/2800/2666/2400/2133 * 11�me G�n Intel� CoreTM (i9/i7/i5) prend en charge DDR4 jusqu'� 3200 ; CoreTM (i3), Pentium� et Celeron� prennent en charge DDR4 jusqu'� 2666. *10�me G�n Intel� CoreTM (i9/i7) prend en charge DDR4 jusqu'� 2933 ; CoreTM (i5/i3), Pentium� et Celeron� prennent en charge DDR4 jusqu'� 2666. * Veuillez consulter la liste de prise en charge des m�moires sur le site Web d'ASRock pour de plus amples informations. (http://www.asrock. com/) � Prend en charge les modules m�moire UDIMM ECC (fonctionne
en mode non-ECC) � Capacit� max. de la m�moire syst�me : 32Go � Prend en charge Intel� Extreme Memory Profile (XMP) 2.0
� 6 x fentes PCI Express 3.0 x16 (PCIE1 � x16 / PCIE2~6 � x1) � 1 x port de minage (M_Port1 � x1)* * Prend en charge le kit rehausseur type USB

Graphiques

� La technologie Intel� UHD Graphics Built-in Visuals et les
sorties VGA sont uniquement prises en charge par les processeurs
int�grant un contr�leur graphique. � 11�me G�n de processeurs Intel� CoreTM prennent en charge
l'architecture graphique Intel� Xe (G�n 12). 10�me G�n de processeurs Intel� CoreTM prennent en charge les graphiques G�n 9

39

Fran�ais

� Prend en charge la technologie HDMI 1,4 avec r�solution maximale de 4K x 2K (4096x2160) @ 30Hz
� Prend en charge les technologies Auto Lip Sync, Deep Color (12bpc), xvYCC et HBR (High Bit Rate Audio) avec port HDMI 1.4 (un �cran compatible HDMI est requis)
� Prend en charge HDCP 2.3 via port HDMI 1.4

R�seau

� Gigabit LAN 10/100/1000 Mo/s � Giga PHY Intel� I219V � Prend en charge la fonction Wake-On-LAN � Prend en charge la protection contre la foudre/les d�charges �lec-
trostatiques � Prend en charge la fonction d'�conomie d'�nergie Ethernet 802.3az � Prend en charge PXE

Connectique du panneau arri�re

� 1 x port souris/clavier PS/2 � 1 x port HDMI � 2 x ports USB 2.0 (Protection contre les d�charges �lectrostatiques) � 2 x ports USB 3.2 Gen1 (Protection contre les d�charges
�lectrostatiques) � 1 x port RJ-45 LAN avec LED (LED ACT/LIEN et LED VITESSE)

Stockage

� 1 x connecteur SATA3 6,0 Go/s, compatibles avec les fonctions NCQ, AHCI et � Hot Plug �
� 1 x socket M.2, prend en charge les modules M.2 SATA3 6,0 Go/s type 2260/2280/22110 touche M

Connecteur

� 1 x embase de panneau syst�me � 1 x embase SPI TPM � 1 x prise DEL d'alimentation et haut-parleur � 1 x connecteur pour ventilateur de CPU (4 broches) * Le connecteur pour ventilateur de CPU prend en charge un ventilateur de CPU d'une puissance maximale de 1 A (12 W). � 8 x connecteurs pour ventilateur de ch�ssis (4 broches) * CHA_FAN3~CHA_FAN8 prend en charge un ventilateur de ch�ssis d'une puissance maximale de 2,5A (30 W). * CPU_FAN1, CHA_FAN1 et CHA_FAN2 peuvent r�gler la vitesse du ventilateur 4 broches.

Fran�ais

40

H510 Pro BTC+

Caract�ristiques du BIOS

� 3 x connecteurs d'alimentation ATX 24 broches � 1 x connecteur d'alimentation 12 V PCIe 8 broches � 4 x connecteurs d'alimentation PCIe 4 broches � 1 x embase USB 2.0 (2 ports USB 2.0 pris en charge) (Protection
contre les d�charges �lectrostatiques) � 1 x bouton d'alimentation � 1 x bouton de r�initialisation
� BIOS UEFI AMI avec prise en charge d'interface graphique multilingue
� Compatible ACPI 6.0 Wake Up Events � Compatible SMBIOS 2.7 � R�glage de la tension CPU Coeur/Cache, CPU GT, VCCSA, DRAM,
VCCIO, VCCIN AUX

Surveillance du mat�riel

� Tachym�tre de ventilateur : CPU, Ventilateur du ch�ssis � Ventilateur silencieux (r�glage automatique de la vitesse du ventila-
teur du ch�ssis d'apr�s la temp�rature du CPU) : CPU, Ventilateur du ch�ssis � Contr�le simultan� des vitesses du ventilateur : CPU, Ventilateur du ch�ssis � Surveillance de la tension d'alimentation : CPU Vcore, +12V, +5V, +3,3V

Syst�me d'exploitation

� Microsoft� Windows� 10 64 bits � Linux : Ubuntu 16.04 LTS / Fedora 25 * Prise en charge des fonctions de base du syst�me d'exploitation Linux uniquement, en raison de la compatibilit� du syst�me Liunx lui-m�me, il n'existe aucune garantie que toutes les fonctions soient prises en charge.

Certifications � FCC, CE � ErP/EuP Ready (alimentation ErP/EuP ready requise)

Fran�ais

41

* pour des informations d�taill�es de nos produits, veuillez visiter notre site : http://www.asrock.com Il est important de signaler que l'overclocking pr�sente certains risques, incluant des modifications du BIOS, l'application d'une technologie d'overclocking d�li�e et l'utilisation d'outils d'overclocking d�velopp�s par des tiers. La stabilit� de votre syst�me peut �tre affect�e par ces pratiques, voire provoquer des dommages aux composants et aux p�riph�riques du syst�me. L'overclocking se fait � vos risques et p�rils. Nous ne pourrons en aucun cas �tre tenus pour responsables des dommages �ventuels provoqu�s par l'overclocking.
42

Fran�ais

H510 Pro BTC+
1.3 Configuration des cavaliers (jumpers)
L'illustration ci-dessous vous renseigne sur la configuration des cavaliers (jumpers). Lorsque le capuchon du cavalier est install� sur les broches, le cavalier est � court-circuit� �. Si le capuchon du cavalier n'est pas install� sur les broches, le cavalier est � ouvert �.

Cavalier Clear CMOS (CLRMOS1) (voir p.1, No. 3)

Cavalier (jumper) � 2 broches

CLRMOS1 vous permet d'effacer les donn�s de la CMOS. Pour effacer les param�tres du syst�me et r�tablir les valeurs par d�faut, veuillez �teindre votre ordinateur et d�brancher son cordon d'alimentation. Patientez 15 secondes, puis utilisez un capuchon de cavalier pour court-circuiter les broches sur CLRMOS1 pendant 5 secondes. Toutefois, n'effacez pas la CMOS imm�diatement apr�s avoir mis � jour le BIOS. Si vous avez besoin d'effacer les donn�es CMOS apr�s une mise � jour du BIOS, vous devez tout d'abord red�marrer le syst�me, puis l'�teindre avant de proc�der � l'effacement de la CMOS. Veuillez noter que les param�tres mot de passe, date, heure et profil de l'utilisateur seront uniquement effac�s en cas de retrait de la pile de la CMOS. N'oubliez pas de retirer le capuchon du cavalier une fois les donn�es CMOS effac�es.

Fran�ais

43

1.4 Embases et connecteurs de la carte m�re
Les embases et connecteurs situ�s sur la carte NE SONT PAS des cavaliers. Ne placez JAMAIS de capuchons de cavaliers sur ces embases ou connecteurs. Placer un capuchon de cavalier sur ces embases ou connecteurs endommagera irr�m�diablement votre carte m�re.

Embase du panneau syst�me (PANNEAU1 � 9 broches) (voir p.1, No. 10)

GND PWRBTN#
PLEDPLED+

GND RESET# GND HDLEDHDLED+ 1

Branchez le bouton de mise en marche, le bouton de r�initialisation et le t�moin d'�tat du syst�me pr�sents sur le ch�ssis sur cette embase en respectant la configuration des broches illustr�e ci-dessous. Rep�rez les broches positive et n�gative avant de brancher les c�bles.

PWRBTN (bouton d'alimentation) : pour brancher le bouton d'alimentation du panneau frontal du ch�ssis. Vous pouvez configurer la fa�on dont votre syst�me doit s'arr�ter � l'aide du bouton d'alimentation.
RESET (bouton de r�initialisation) : pour brancher le bouton de r�initialisation du panneau frontal du ch�ssis. Appuyez sur le bouton de r�initialisation pour red�marrer l'ordinateur en cas de plantage ou de dysfonctionnement au d�marrage.
PLED (LED d'alimentation du syst�me) : pour brancher le t�moin d'�tat de l'alimentation du panneau frontal du ch�ssis. Le LED est allum� lorsque le syst�me fonctionne. Le LED clignote lorsque le syst�me se trouve en mode veille S1/S3. Le LED est �teint lorsque le syst�me se trouve en mode veille S4 ou hors tension (S5).
HDLED (LED d'activit� du disque dur) : pour brancher le t�moin LED d'activit� du disque dur du panneau frontal du ch�ssis. Le LED est allum� lorsque le disque dur lit ou �crit des donn�es.
La conception du panneau frontal peut varier en fonction du ch�ssis. Un module de panneau frontal est principalement compos� d'un bouton d'alimentation, d'un bouton de r�initialisation, d'un t�moin LED d'alimentation, d'un t�moin LED d'activit� du disque dur, d'un haut-parleur etc. Lorsque vous reliez le module du panneau frontal de votre ch�ssis sur cette embase, veillez � parfaitement faire correspondre les fils et les broches.

Fran�ais

44

H510 Pro BTC+

Prise DEL d'alimentation et haut-parleur (SPK_PLED1 � 7 broches) (voir p.1, No. 11)

SPEAKER DUMMY DUMMY +5V

PLEDPLED+ PLED+
1

Veuillez brancher la DEL d'alimentation du ch�ssis et le haut-parleur du ch�ssis sur ce connecteur.

Connecteur Serial ATA3 Angle droit: (SATA_1: voir p.1, No. 13)

Ce connecteur SATA3 prend en charge les c�bles de donn�es SATA pour les p�riph�riques de stockage internes avec un taux de transfert maximal de 6,0 Go/s.

Embase USB 2.0 (USB_3_4 � 9 broches) (voir p.1, No. 9)

DUMMY GND P+ P-
USB_PWR

GND P+ PUSB_PWR 1

Cette carte m�re comprend un connecteur. Cette embase USB 2.0 peut prendre en charge deux ports.

Connecteurs du ventilateur du ch�ssis (CHA_FAN1 � 4 broches) (voir p.1, No. 4)

4 3 21
FAN_SPEED_CONTROL CHA_FAN_SPEED FAN_VOLTAGE GND

Veuillez brancher les c�bles du ventilateur sur les connecteurs du ventilateur, puis reliez le fil noir � la broche de mise � terre.

1

(CHA_FAN2 � 4 broches) 2

3

(voir p.1, No. 12)

4

GND FAN_VOLTAGE CHA_FAN_SPEED FAN_SPEED_CONTROL

Fran�ais

45

(CHA_FAN3 � 4 broches) (voir p.1, No. 26) (CHA_FAN4 4 broches) (voir p.1, No. 25) (CHA_FAN5 � 4 broches) (voir p.1, No. 17) (CHA_FAN6 � 4 broches) (voir p.1, No. 24) (CHA_FAN7 � 4 broches) (voir p.1, No. 20) (CHA_FAN8 � 4 broches) (voir p.1, No. 23)

4 3 21
FAN_SPEED_CONTROL CHA_FAN_SPEED +12V GND

Connecteur du ventilateur du processeur (CPU_FAN1 � 4 broches) (voir p.1, No. 1)
Connecteurs d'alimentation ATX (ATXPWR1 � 24 broches) (voir p.1, No. 8) (ATXPWR2 � 24 broches) (voir p.1, No. 7) (ATXPWR3 � 24 broches) (voir p.1, No. 21)
Connecteur d'alimentation ATX 12 V (ATX12V1 � 8 broches) (voir p.1, No. 27)

FAN_SPEED_CONTROL CPU_FAN_SPEED
+12V GND
1 2 34

12

24

1

13

5

1

8

4

Cette carte m�re est dot�e d'un connecteur pour ventilateur de processeur (Quiet Fan) � 4 broches. Si vous envisagez de connecter un ventilateur de processeur � 3 broches, veuillez le brancher sur la broche 1-3.
Cette carte m�re est dot�e de trois connecteurs d'alimentation ATX � 24 broches. Pour utiliser une alimentation ATX � 20 broches, veuillez effectuer les branchements sur la Broche 1 et la Broche 13.
Cette carte m�re est dot�e d'un connecteur d'alimentation ATX 12 V � 8 broches. Pour utiliser une alimentation ATX � 4 broches, veuillez effectuer les branchements sur la Broche 1 et la Broche 5.

Fran�ais

46

H510 Pro BTC+

Connecteurs d'alimentation PCIe (PCIE_PWR3 � 4 broches) (voir p.1, No. 16) (PCIE_PWR4 � 4 broches) (voir p.1, No. 18) (PCIE_PWR5 � 4 broches) (voir p.1, No. 19) (PCIE_PWR6 � 4 broches) (voir p.1, No. 22)
Port de minage (M_Port1:voir p.1, No. 15)

Veuillez raccorder ces connecteurs aux alimentations �lectriques.
Important : Assurez-vous que le connecteur d'alimentation PCIe 4 broches et le connecteur d'alimentation externe de la carte graphique sont raccord�s au m�me bloc d'alimentation �lectrique. Dans le cas contraire, la carte m�re et la carte graphique peuvent �tre endommag�es.
Veuillez raccorder ce port au kit �l�vateur.

9 PERXN PERXP 8
GND 7 PETXP 6 PETXN 5

1 WAKE# 2 CLKN 3 CLKP 4 RST

Embase SPI TPM (SPI_TPM_J1 � 13 broches) (voir p.1, No. 14)

SPI_DQ3 +3.3V Dummy CLK SPI_MOSI RST# TPM_PIRQ
1
SPI_TPM_CS# GND RSMRST# SPI_MISO SPI_CS0 SPI_DQ2

Ce connecteur prend en charge un module SPI TPM (Trusted Platform Module � Module de plateforme s�curis�e), qui permet de sauvegarder cl�s, certificats num�riques, mots de passe et donn�es en toute s�curit�. Le syst�me TPM permet �galement de renforcer la s�curit� du r�seau, de prot�ger les identit�s num�riques et de pr�server l'int�grit� de la plateforme.

Fran�ais

47

1.5 Boutons intelligents
La carte m�re dispose de deux boutons intelligents : Bouton d'alimentation et bouton de r�initialisation.

Bouton d'alimentation (PWRBTN1) (voir p.1, No. 5)

Le bouton d'alimentation permet aux utilisateurs d'allumer/�teindre le syst�me rapidement.

Bouton de r�initialisation (RSTBTN1) (voir p.1, No. 6)

Le bouton de r�initialisation permet aux utilisateurs de r�initialiser le syst�me rapidement.

Fran�ais

48

H510 Pro BTC+
1 Introduzione
Congratulazioni per l'acquisto della scheda madre ASRock H510 Pro BTC+, una scheda madre affidabile prodotta secondo i severissimi controlli di qualit� ASRock. La scheda madre offre eccellenti prestazioni con un design robusto che si adatta all'impegno di ASRock di offrire sempre qualit� e durata.
Dato che le specifiche della scheda madre e del software BIOS possono essere aggiornate, il contenuto di questa documentazione sar� soggetto a variazioni senza preavviso. Nel caso di eventuali modifiche della presente documentazione, la versione aggiornata sar� disponibile sul sito Web di ASRock senza ulteriore preavviso. Per il supporto tecnico correlato a questa scheda madre, visitare il nostro sito Web per informazioni specifiche relative al modello attualmente in uso. � possibile trovare l'elenco di schede VGA pi� recenti e di supporto di CPU anche sul sito Web di ASRock. Sito Web di ASRock http:// www.asrock.com.
1.1 Contenuto della confezione
� Scheda madre ASRock H510 Pro BTC+ � Guida all'installazione rapida di ASRock H510 Pro BTC+ � CD di supporto ASRock H510 Pro BTC+ � 1 x cavo dati Serial ATA (SATA) (opzionali) � 1 x viti per Socket M.2 (opzionali)
49

Italiano

1.2 Specifiche

Piattaforma � Design condensatore solido

CPU

� Supporta processori 10� Gen Intel� CoreTM e processori 11� Gen Intel� CoreTM (LGA1200)
� Digi Power design � Potenza a 4 fasi � Supporta la tecnologia Intel� Turbo Boost Max 3.0

Chipset

� Intel� H510

Memoria

� 1 x alloggio DIMM DDR4 * Non sono supportati 2GB DRAM per modulo. � Supporto di memoria DDR4 3200/2933/2800/2666/2400/2133 non-
ECC, un-buffered * 11� Gen Intel� CoreTM (i9/i7/i5) supportano DDR4 fino a 3200; CoreTM (i3), Pentium� e Celeron� supportano DDR4 fino a 2666. * 10� Gen Intel� CoreTM (i9/i7) supportano DDR4 fino a 2933; CoreTM
(i5/i3), Pentium� e Celeron� supportano DDR4 fino a 2666.
* Per maggiori informazioni fare riferimento all'elenco dei supporti di
memoria sul sito di ASRock. (http://www.asrock.com/) � Supporta moduli di memoria ECC UDIMM (funziona in modalit�
non ECC) � Capacit� max. della memoria di sistema: 32 GB � Supporto di XMP (Extreme Memory Profile) Intel� 2.0

Alloggio d'espansione

� 6 x Alloggi PCI Express 3.0 x16 (PCIE1 a x16 / PCIE2~6 a x1) � 1 x Port mining (M_Port1 a x1)*
* Supporto di kit Riser di tipo USB

Grafica

� La videografica integrata della scheda video UHD Intel� e le uscite VGA possono essere supportate soltanto con processori con GPU integrata.
� I processori 11� Gen Intel� CoreTM supportano architettura grafica Intel� Xe (Gen 12). processori 10� Gen Intel� CoreTM supportano grafica Gen 9

Italiano

50

H510 Pro BTC+

� Supporta HDMI 1,4 con risoluzione massima fino a 4K x 2K (4096 x 2160) a 30Hz
� Supporto delle funzioni Auto Lip Sync, Deep Color (12bpc), xvYCC e HBR (High Bit Rate Audio) con porta HDMI 1.4 (� necessario un monitor compatibile HDMI)
� Supporta HDCP 2.3 con porta HDMI 1.4

LAN

� LAN Gigabit 10/100/1000 Mb/s

� Giga PHY Intel� I219V

� Supporto WOL (Wake-On-LAN)

� Supporta protezione da fulmini/scariche elettrostatiche

� Supporto Energy Efficient Ethernet 802.3az

� Supporto PXE

I/O pannello posteriore

� 1 x porta mouse/tastiera PS/2 � 1 x porta HDMI � 2 x porte USB 2.0 (supporto protezione da scariche elettrostatiche) � 2 x porte USB 3.2 Gen1 (supporto protezione da scariche
elettrostatiche) � 1 x porta LAN RJ-45 con LED (ACT/LINK LED e SPEED LED)

Archiviazione

� 1 x connettore SATA3 6.0 Gb/s supportano NCQ, AHCI e Hot Plug � 1 x M.2 Socket, supporto modulo M.2 SATA3 6,0 Gb/s tipo
2260/2280/22110

Connettore

� 1 x Connettore pannello frontale � 1 x connettore SPI TPM � 1 x connettore LED alimentazione e altoparlante � 1 x connettore ventola CPU (4-pin)
* Il connettore ventola CPU supporta ventole CPU con potenza massi-
ma di 1 A (12 W). � 8 x connettori ventola chassis (4 pin)
* CHA_FAN3~CHA_FAN8 supporta ventole telaio con potenza massi-
ma di 2,5A (30W).
* CPU_FAN1, CHA_FAN1 e CHA_FAN2 possono regolare la velocit�
della ventola 4 pin. � 3 x connettori alimentazione ATX 24 pin � 1 x Connettore alimentazione PCIe 12V 8 pin

Italiano

51

� 4 x Connettore alimentazione PCIe 4 pin � 1 x connettore USB 2.0 (supporto di 2 porte USB 2.0) (supporto
protezione da scariche elettrostatiche) � 1 x Tasto d'alimentazione � 1 x Tasto Ripristino

Funzionalit� BIOS

� AMI UEFI Legal BIOS con interfaccia di supporto multilingue � Eventi di riattivazione conformi a ACPI 6.0 � Supporto di SMBIOS 2.7 � Regolazione multipla tensione CPU Core/Cache, CPU GT, VCCSA,
DRAM, VCCIO, VCCIN AUX

Hardware Monitor

� Tachimetro ventola: CPU, Ventola chassis � Ventola silenziosa (regolazione automatica velocit� in base alla
temperatura della CPU): CPU, Ventola chassis � Controllo velocit� ventola: CPU, Ventola chassis � Monitoraggio tensione: CPU Vcore, +12V, +5V, +3,3V

SO

� Microsoft� Windows� 10 64 bit

� Linux: Ubuntu 16.04 LTS / Fedora 25

* Supporto solo per le funzioni di base del sistema operativo Linux, a

causa della compatibilit� del sistema Linux stesso, non � garantito che

tutte le funzioni siano supportate.

Certificazioni � FCC, CE � ErP/EuP Ready (� necessaria alimentazione ErP/EuP ready)

* Per informazioni dettagliate sul prodotto, visitare il nostro sito Web: http://www.asrock.com
Prestare attenzione al potenziale rischio previsto nella pratica di overclocking, inclusa la regolazione delle impostazioni nel BIOS, l'applicazione di tecnologia di Untied Overclocking o l'utilizzo di strumenti di overclocking di terze parti. L'overclocking pu� influenzare la stabilit� del sistema o perfino provocare danni ai componenti e ai dispositivi del sistema. Occorre eseguirlo a proprio rischio e spese. Non ci riterremo responsabili per possibili danni provocati da overclocking.

Italiano

52

H510 Pro BTC+
1.3 Impostazione jumper
L'illustrazione mostra in che modo vengono impostati i jumper. Quando il cappuccio del jumper � posizionato sui pin, il jumper � "cortocircuitato". Se sui pin non � posizionato alcun cappuccio del jumper, il jumper � "aperto".

Jumper per azzerare la CMOS (CLRMOS1) (vedere pag. 1, n. 3)

Jumper a 2 pin

CLRMOS1 permette si azzerare i dati nella CMOS. Per azzerare e reimpostare i parametri del sistema alla configurazione predefinita, spegnere il computer e scollegare il cavo di alimentazione dalla rete. Attendere 15 secondi, quindi usare un cappuccio jumper per cortocircuitare i di CLRMOS1 per 5 secondi. Tuttavia, non azzerare la CMOS subito dopo aver aggiornato il BIOS. Se � necessario azzerare la CMOS dopo l'aggiornamento del BIOS, � necessario riavviare prima il sistema e in seguito spegnerlo prima di eseguire l'operazione di azzeramento della CMOS. La password, la data, l'ora e il profilo predefinito dell'utente saranno azzerati solo se viene rimossa la batteria della CMOS. Ricordarsi di rimuovere il cappuccio jumper prima di cancellare la CMOS.

Italiano

53

1.4 Header e connettori su scheda
Gli header e i connettori sulla scheda NON sono jumper. NON posizionare cappucci del jumper su questi header e connettori. Il posizionamento di cappucci del jumper su header e connettori provocher� danni permanenti alla scheda madre.

Header sul pannello del sistema (PANEL1 a 9 pin) (vedere pag. 1, n. 10)

GND PWRBTN#
PLEDPLED+

GND RESET# GND HDLEDHDLED+ 1

Collegare il tasto d'alimentazione, il tasto di ripristino e l'indicatore di stato del sistema del telaio a questa basetta in base all'assegnazione dei pin definita di seguito. Annotare i pin positivi e negativi prima di collegare i cavi.

PWRBTN (tasto d'alimentazione): Collegare al tasto d'alimentazione del pannello frontale del telaio. Utilizzando il tasto d'alimentazione � possibile configurare il modo in cui si spegne il sistema.
RESET (tasto di ripristino): Collegare all'interruttore di ripristino del pannello frontale del telaio. Premere il tasto di ripristino per riavviare il sistema se il computer si blocca e non riesce ad eseguire un normale riavvio.
PLED (LED alimentazione del sistema): collegare all'indicatore di stato dell'alimentazione sul pannello anteriore dello chassis. Il LED � acceso quando il sistema � in funzione. Il LED continua a lampeggiare quando il sistema si trova nello stato di sospensione S1/S3. Il LED � spento quando il sistema si trova nello stato di sospensione S4 o quando � spento (S5).
HDLED (LED di attivit� disco rigido): collegare al LED di attivit� disco rigido sul pannello anteriore dello chassis. Il LED � acceso quando il disco rigido sta leggendo o scrivendo dati.
Il design del pannello anteriore pu� cambiare a seconda dello chassis. Un modulo del pannello frontale consiste principalmente di tasto d'alimentazione, tasto di ripristino, LED d'alimentazione, LED attivit� del disco rigido, altoparlanti e cos� via. Quando si collega il modulo del pannello frontale del telaio a questa basetta, assicurarsi che l'assegnazione dei cavi e l'assegnazione dei pin siano corrette.

Italiano

54

H510 Pro BTC+

Connettore LED alimentazione e altoparlante (SPK_PLED1 a 7 pin) (vedere pag. 1, n. 11)

SPEAKER DUMMY DUMMY +5V

PLEDPLED+ PLED+
1

Collegare i LED alimentazione e l'altoparlante a questo connettore.

Connettore Serial ATA3 Angolo destroy: (SATA_1: vedere pag.1, n. 13)
Connettore USB 2.0 (USB_3_4 a 9 pin) (vedere pag. 1, n. 9)

Questo connettore SATA3 supporta i cavi dati SATA per dispositivi di archiviazione interna, con una velocit� di trasferimento dati fino a 6,0 Gb/s.

DUMMY GND P+ P-
USB_PWR

GND P+ PUSB_PWR 1

Su questa scheda madre c'� un connettore. Questo connettore USB 2.0 pu� supportare due porte.

Connettori ventola telaio (CHA_FAN1 a 4 pin) (vedere pag. 1, n. 4)

4 3 21
FAN_SPEED_CONTROL CHA_FAN_SPEED FAN_VOLTAGE GND

Collegare i cavi della ventola ai connettori della ventola e far corrispondere il filo nero al pin di terra.

(CHA_FAN2 a 4 pin) (vedere pag. 1, n. 12)

1

GND

2

FAN_VOLTAGE

3

CHA_FAN_SPEED

4

FAN_SPEED_CONTROL

Italiano

55

(CHA_FAN3 a 4 pin) (vedere pag. 1, n. 26) (CHA_FAN4 a 4 pin) (vedere pag. 1, n. 25) (CHA_FAN5 a 4 pin) (vedere pag. 1, n. 17) (CHA_FAN6 a 4 pin) (vedere pag. 1, n. 24) (CHA_FAN7 a 4 pin) (vedere pag. 1, n. 20) (CHA_FAN8 a 4 pin) (vedere pag. 1, n. 23)

4 3 21
FAN_SPEED_CONTROL CHA_FAN_SPEED +12V GND

Connettore ventola CPU (CPU_FAN1 a 4 pin) (vedere pag. 1, n. 1)

FAN_SPEED_CONTROL CPU_FAN_SPEED
+12V GND
1 2 34

Questa scheda madre � dotata di un connettore per la ventola della CPU (Ventola silenziosa) a 4 pin. Se si decide di collegare una ventola della CPU a 3 pin, collegarla al pin 1-3.

Connettori di alimentazione ATX (ATXPWR1 a 24 pin) (vedere pag. 1, n. 8) (ATXPWR2 a 24 pin) (vedere pag. 1, n. 7) (ATXPWR3 a 24 pin) (vedere pag. 1, n. 21)
Connettore di alimentazione ATX da 12 V (ATX12V1 a 8 pin) (vedere pag. 1, n. 27)

12

24

1

13

Questa scheda madre � dotata di tre connettori di alimentazione ATX a 24 pin. Per utilizzare un'alimentazione ATX a 20 pin, collegarla lungo il pin 1 e il pin 13.

5

1

Questa scheda madre � dotata di

un connettore di alimentazione

ATX da 12 V a 8 pin. Per utilizza-

re un'alimentazione ATX a 4 pin,

8

4

collegarla lungo il pin 1 e il pin 5.

Italiano

56

H510 Pro BTC+

Connettori alimentazione PCIe (PCIE_PWR3 a 4 pin) (vedere pag. 1, n. 16) (PCIE_PWR4 a 4 pin) (vedere pag. 1, n. 18) (PCIE_PWR5 a 4 pin) (vedere pag. 1, n. 19) (PCIE_PWR6 a 4 pin) (vedere pag. 1, n. 22)

Collegare questi connettori agli alimentatori.
Importante: Assicurarsi che il connettore di alimentazione PCIe 4 pic ed il conntettore di alimentazione esterno della scheda grafica siano collegati alla stessa PSU; diversamente la scheda madre e la scheda grafica possono subire danni.

Port mining (M_Port1:(vedere pag.1, n. 15)
9 PERXN PERXP 8
GND 7 PETXP 6 PETXN 5

1 WAKE# 2 CLKN 3 CLKP 4 RST

Collegare questa porta al kit riser.

Connettore SPI TPM (SPI_TPM_J1 a 13 pin) (vedere pag. 1, n. 14)

SPI_DQ3 +3.3V Dummy CLK SPI_MOSI RST# TPM_PIRQ
1
SPI_TPM_CS# GND RSMRST# SPI_MISO SPI_CS0 SPI_DQ2

Questo connettore supporta il sistema SPI Trusted Platform Module (TPM), che pu� archiviare in modo sicuro chiavi, certificati digitali, password e dati. Un sistema TPM permette anche di potenziare la sicurezza della rete, di proteggere identit� digitali e di garantire l'integrit� della piattaforma.

Italiano

57

1.5 Interruttori intuitivi
La scheda madre � dotata di due interruttori intuitivi: Tasto di alimentazione e di ripristino.

Tasto d'alimentazione (PWRBTN1) (vedere pag. 1, n. 5)

Il tasto d'alimentazione consente di accendere/spegnere rapidamente il sistema.

Tasto di ripristino (RSTBTN1) (vedere pag. 1, n. 6)

Il tasto di ripristino consente di ripristinare rapidamente il sistema.

Italiano

58

H510 Pro BTC+
1 Introducci�n
Gracias por comprar la placa base ASRock H510 Pro BTC+, una placa base fiable fabricada seg�n el riguros�simo control de calidad de ASRock. Ofrece un rendimiento excelente con un dise�o resistente de acuerdo con el compromiso de calidad y resistencia de ASRock.
Ya que las especificaciones de la placa base y el software de la BIOS podr�n ser actualizados, el contenido que aparece en esta documentaci�n estar� sujeto a modificaciones sin previo aviso. Si esta documentaci�n sufre alguna modificaci�n, la versi�n actualizada estar� disponible en el sitio web de ASRock sin previo aviso. Si necesita asistencia t�cnica relacionada con esta placa base, visite nuestro sitio web para obtener informaci�n espec�fica sobre el modelo que est� utilizando. Podr� encontrar las �ltimas tarjetas VGA, as� como la lista de compatibilidad de la CPU, en el sitio web de ASRock. Sitio web de ASRock http://www.asrock.com.
1.1 Contenido del paquete
� Placa base ASRock H510 Pro BTC+ � Gu�a de instalaci�n r�pida de ASRock H510 Pro BTC+ � CD de soporte de ASRock H510 Pro BTC+ � 1 x Cable de datos Serie ATA (SATA) (Opcional) � 1 x tornillo para socket M.2 (opcional)
59

Espa�ol

1.2 Especificaciones

Plataforma � Dise�o de condensador s�lido

CPU

� Admite procesadores Intel� CoreTM de la 10� generaci�n y procesadores Gen Intel� CoreTM de la 11� generaci�n (LGA1200)
� Digi Power design � Dise�o de 4 fases de alimentaci�n � Admite Intel� Turbo Boost Technology 3.0

Conjunto de chips

� Intel� H510

Memoria

� 1 x ranura DIMM DDR4 * 2GB DRAM por m�dulo no es compatible. � Admite memoria DDR4 3200/2933/2800/2666/2400/2133 no ECC,
sin b�fer * Intel� CoreTM (i9/i7/i5) de la 11� generaci�n admiten DDR4 de hasta 3200; CoreTM (i3), Pentium� y Celeron� compatible con DDR4 de hasta
2666. Intel� CoreTM (i9/i7) de la 10� generaci�n admiten DDR4 de hasta 2933; CoreTM (i5/i3), Pentium� y Celeron� compatible con DDR4 de hasta
2666.
* Para obtener m�s informaci�n, consulte la lista de memorias
compatibles en el sitio web de ASRock. (http://www.asrock.com/) � Admite m�dulos de memoria UDIMM ECC (funcionamiento en
modo no ECC) � Capacidad m�xima de memoria del sistema: 32GB � Admite Perfil de memoria extremo de Intel� (XMP) 2.0

Ranura de expansi�n

� 6 ranuras PCI Express 3.0 x16 (PCIE1 a x16/PCIE2 ~ 6 a x1) � 1 x Puertos de miner�a (M_Port1 a x1)*
* Compatibilidad con kit USB tipo Riser

Gr�ficos

� Intel� UHD Graphics Built-in Visuals y las salidas de VGA son
compatibles �nicamente con procesadores con GPU integrado. � Los procesadores Gen Intel� CoreTM de la 11� generaci�n admiten la
arquitectura de gr�ficos Intel� Xe (Gen 12). Los procesadores Intel� CoreTM de la 10� generaci�n admiten gr�ficos de la 9� generaci�n.

Espa�ol

60

H510 Pro BTC+

� Compatible con HDMI 1,4 con una resoluci�n m�xima de 4K x 2K (4096x2160) a 30Hz
� Admite Sincronizaci�n autom�tica entre audio y v�deo, color profundo (12 bpc), xvYCC y HBR (audio de alta tasa de bits) con puerto HDMI 1.4 (se necesita un monitor compatible con HDMI)
� Admite HDCP 2.3 con puerto HDMI 1.4

LAN

� Gigabit LAN 10/100/1000 Mb/s

� Giga PHY Intel� I219V

� Admite la funci�n Reactivaci�n de LAN

� Admite protecci�n contra rayos y descargas electrost�ticas (ESD)

� Admite Ethernet 802.3az de eficiencia energ�tica

� Admite PXE

E/S en panel posterior

� 1 x puerto de rat�n/teclado PS/2 � 1 x puerto HDMI � 2 x Puertos USB 2.0 (admite protecci�n contra descargas
electrost�ticas) � 2 x Puertos USB 3.2 Gen1 (admite protecci�n contra descargas
electrost�ticas) � 1 x Puerto LAN RJ-45 con LED (LED DE ACTIVIDAD/ENLACE y
LED DE VELOCIDAD)

Almacenamiento

� 1 x Conector SATA3 de 6,0 Gb/s, compatible con las funciones NCQ, AHCI y Conexi�n en caliente
� 1 x Z�calo M.2, admite el m�dulo SATA3 6,0 Gb/s M.2 de tipo 2260/2280/22110 con clave M

Conector

� 1 x Base de conexiones en el panel del sistema � 1 x Conector SPI TPM � 1 x LED de alimentaci�n y base de conexiones para el altavoz � 1 x Conector para ventilador de la CPU (4 contactos) * El conector para ventilador de la CPU admite ventilador de la CPU con una potencia de ventilador de 1 A (12 W) m�xima. � 8 x conectores de ventilador del chasis (de 4 contactos) * CHA_FAN3~CHA_FAN8 admite el ventilador del chasis con una potencia de ventilador m�xima de 2,5A (30 W). * CPU_FAN1, CHA_FAN1 y CHA_FAN2 pueden ajustar la velocidad del ventilador de 4 contactos.

Espa�ol

61

� 3 x conectores de alimentaci�n ATX de 24 contactos � 1 x Conector de alimentaci�n de 12 V PCIe de 8 contactos � 4 x Conectores de alimentaci�n PCIe de 4 contactos � 1 x Base de conexiones USB 2.0 (admite 2 puertos USB 2.0) (admite
protecci�n contra descargas electrost�ticas) � 1 x Bot�n de alimentaci�n � 1 x Bot�n Restablecer

Funci�n de la BIOS

� BIOS legal UEFI AMI compatible con interfaz gr�fica de usuario
multiling�e � Eventos de reactivaci�n compatibles con ACPI 6.0 � Admite SMBIOS 2.7 � Varios ajustes de voltaje de n�cleo y cach� de CPU, GT de CPU,
VCCSA, DRAM, VCCIO y VCCIN AUX

Monitor de hardware
SO

� Tac�metro del ventilador: CPU, ventiladores del chasis � Ventilador silencioso (ajuste autom�tico de la velocidad del venti-
lador del chasis por temperatura de la CPU): CPU, ventiladores del chasis � Control de varias velocidades del ventilador: CPU, ventiladores del chasis � Supervisi�n del voltaje: Vcore de CPU, +12 V, +5 V, +3,3 V
� Microsoft� Windows� 10 64 bits � Linux: Ubuntu 16.04 LTS / Fedora 25 * Solamente admite funciones b�sicas del sistema operativo Linux. Debido a la compatibilidad del propio sistema Linux, no hay garant�a de que todas las funciones se admitan.

Certificaciones

� FCC y CE � Preparado para ErP/EuP (se necesita una fuente de alimentaci�n
preparada para ErP/EuP)

Espa�ol

62

H510 Pro BTC+
* Para obtener informaci�n detallada del producto, visite nuestro sitio Web: http://www.asrock.com Tenga en cuenta que hay un cierto riesgo impl�cito en las operaciones de overclocking, incluido el ajuste de la BIOS, aplicando la tecnolog�a de overclocking liberada o utilizando las herramientas de overclocking de otros fabricantes. El overclocking puede afectar a la estabilidad del sistema e, incluso, da�ar los componentes y dispositivos del sistema. Esta operaci�n se debe realizar bajo su propia responsabilidad y usted debe asumir los costos. No asumimos ninguna responsabilidad por los posibles da�os causados por el overclocking.
63

Espa�ol

1.3 Instalaci�n de los puentes
La instalaci�n muestra c�mo deben instalarse los puentes. Cuando la tapa de puente se coloca en los contactos, el puente queda "Corto". Si no coloca la tapa de puente en los contactos, el puente queda "Abierto".

Puente de borrado de CMOS (CLRMOS1) (consulte la p�g. 1, n� 3)

Puente de 2 contactos

CLRMOS1 le permite borrar los datos del CMOS. Para borrar y restablecer los par�metros del sistema a los valores predeterminados de instalaci�n, apague el ordenador y desenchufe el cable de alimentaci�n de la toma de alimentaci�n. Despu�s de esperar 15 segundos, utilice una tapa de puente para acortar los contactos en el CLRMOS1 durante 5 segundos. Sin embargo, no borre el CMOS justo despu�s de que haya actualizado la BIOS. Si necesita borrar el CMOS cuando acabe de actualizar la BIOS, deber� arrancar el sistema primero y, a continuaci�n, deber� apagarlo antes de que realice el borrado del CMOS. Tenga en cuenta que la contrase�a, la fecha, la hora y el perfil de usuario predeterminado ser�n eliminados �nicamente si se retira la pila del CMOS. Acu�rdese de retirar la tapa de puente despu�s de borrar el CMOS.

Espa�ol

64

H510 Pro BTC+

1.4 Conectores y cabezales incorporados
Los cabezales y conectores incorporados NO son puentes. NO coloque tapas de puente sobre estos cabezales y conectores. Si coloca tapas de puente sobre los cabezales y conectores da�ar� de forma permanente la placa base.

Cabezal del panel del sistema (PANEL1 de 9 contactos) (consulte la p�g. 1, n� 10)

GND PWRBTN#
PLEDPLED+

GND RESET# GND HDLEDHDLED+ 1

Conecte el bot�n de alimentaci�n, el bot�n de restablecimiento y el indicador de estado del sistema que se encuentran en el chasis a esta base de conexiones seg�n las asignaciones de contactos que se indica a continuaci�n. Cerci�rese de cu�les son los contactos positivos y los negativos antes de conectar los cables.

PWRBTN (bot�n de alimentaci�n): Con�ctelo al bot�n de alimentaci�n del panel frontal del chasis. Deber� configurar la forma en la que su sistema se apagar� mediante el bot�n de alimentaci�n.
RESET (bot�n de restablecimiento): Con�ctelo al bot�n de restablecimiento del panel frontal del chasis. Pulse el bot�n de restablecimiento para resetear el ordenador si �ste est� bloqueado y no se puede reiniciar de forma normal.
PLED (Indicador LED de la alimentaci�n del sistema): Con�ctelo al indicador de estado de la alimentaci�n del panel frontal del chasis. El indicador LED permanece encendido cuando el sistema est� funcionando. El indicador LED parpadea cuando el sistema se encuentra en estado de suspensi�n S1/S3. El indicador LED se apaga cuando el sistema se encuentra en estado de suspensi�n S4 o est� apagado (S5).
HDLED (Indicador LED de actividad en el disco duro): Con�ctelo al indicador LED de actividad en el disco duro del panel frontal del chasis. El indicador LED permanece encendido cuando el disco duro est� leyendo o escribiendo datos.
El dise�o del panel frontal puede ser diferente dependiendo del chasis. Un m�dulo de panel frontal consta principalmente de: bot�n de alimentaci�n, bot�n de restablecimiento, indicador LED de alimentaci�n, indicador LED de actividad en el disco duro, altavoz, etc. Cuando conecte su m�dulo del panel frontal del chasis a este cabezal, aseg�rese de que las asignaciones de los cables y los contactos coinciden correctamente.

Espa�ol

65

LED de alimentaci�n y base de conexiones para la altavoz (SPK_PLED1 de 7 contactos) (consulte la p�g. 1, n� 11)

SPEAKER DUMMY DUMMY +5V

PLEDPLED+ PLED+
1

Conecte el LED de alimentaci�n del chasis y el altavoz del chasis a esta base de conexiones.

Conector Serie ATA3 �ngulo recto: (SATA_1: consulte la p�g. 1, n� 13)

Este conector SATA3 es compatible con cables de datos SATA para dispositivos de almacenamiento interno con una velocidad de transferencia de datos de hasta 6,0 Gb/s.

Cabezal USB 2.0 (USB_3_4 de 9 contactos) (consulte la p�g. 1, n� 9)

DUMMY GND P+ P-
USB_PWR

GND P+ PUSB_PWR 1

Esta placa base tiene otra base de conexiones. Cada base de conexiones USB 2.0 admite dos puertos.

Conectores para el ventilador del chasis (CHA_FAN1 de 4 contactos) (consulte la p�g. 1, n� 4)

4 3 21
FAN_SPEED_CONTROL CHA_FAN_SPEED FAN_VOLTAGE GND

Conecte los cables del ventilador a los conectores del ventilador y haga coincidir el cable negro con el contacto de conexi�n a tierra.

(CHA_FAN2 de 4 contac-

tos)

1 2

(consulte la p�g. 1, n� 12) 3 4

GND FAN_VOLTAGE CHA_FAN_SPEED FAN_SPEED_CONTROL

Espa�ol

66

H510 Pro BTC+

(CHA_FAN3 de 4 contactos) (consulte la p�g. 1, n� 26) (CHA_FAN4 de 4 pines) (consulte la p�g. 1, n� 25) (CHA_FAN5 de 4 contactos) (consulte la p�g. 1, n� 17) (CHA_FAN6 de 4 contactos) (consulte la p�g. 1, n� 24) (CHA_FAN7 de 4 contactos) (consulte la p�g. 1, n� 20) (CHA_FAN8 de 4 contactos) (consulte la p�g. 1, n� 23)

4 3 21
FAN_SPEED_CONTROL CHA_FAN_SPEED +12V GND

Conector del ventilador de la CPU (CPU_FAN1 de 4-pines) (consulte la p�g. 1, n� 1)
Conectores de alimentaci�n ATX (ATXPWR1 de 24 contactos) (consulte la p�g. 1, n� 8) (ATXPWR2 de 24 contactos) (consulte la p�g. 1, n� 7) (ATXPWR3 de 24 contactos) (consulte la p�g. 1, n� 21)

FAN_SPEED_CONTROL CPU_FAN_SPEED
+12V GND
1 2 34

12

24

1

13

Esta placa base contiene un conector de ventilador (ventilador silencioso) de CPU de 4 contactos. Si tiene pensando conectar un ventilador de CPU de 3 contactos, con�ctelo al contacto 1-3.
Esta placa base contiene tres conectores de alimentaci�n ATX de 24 contactos. Para utilizar una toma de alimentaci�n ATX de 20 contactos, con�ctela en los contactos del 1 al 13.

Espa�ol

67

Conector de alimentaci�n

5

1

ATX de 12 V

(ATX12V1 de 8 contactos)

(consulte la p�g. 1, n� 27)

8

4

Conectores de alimentaci�n PCIe (PCIE_PWR3 de 4 contactos) (consulte la p�g. 1, n� 16) (PCIE_PWR4 de 4 contactos) (consulte la p�g. 1, n� 18) (PCIE_PWR5 de 4 contactos) (consulte la p�g. 1, n� 19) (PCIE_PWR6 de 4 contactos) (consulte la p�g. 1, n� 22)
Puerto de miner�a (M_Port1:consulte la p�g. 1, n� 15)

Esta placa base contiene un conector de alimentaci�n ATX de 12 V y 8 contactos. Para utilizar una toma de alimentaci�n ATX de 4 contactos, con�ctela en los contactos del 1 al 5.
Conecte estos conectores a los suministros de alimentaci�n.
Importante: Aseg�rese de que el conector de alimentaci�n PCIe de 4 contactos y el conector de alimentaci�n externo de la tarjeta gr�fica est�n conectados a la misma fuente de alimentaci�n; de lo contrario, la placa base y la tarjeta gr�fica pueden da�arse.
Conecte este puerto al kit elevador.

Espa�ol

PERXN 9 PERXP 8
GND 7 PETXP 6 PETXN 5

1 WAKE# 2 CLKN 3 CLKP 4 RST

Conector SPI TPM (SPI_TPM_J1 de 13 contactos) (consulte la p�g. 1, n� 14)

SPI_DQ3 +3.3V Dummy CLK SPI_MOSI RST# TPM_PIRQ
1
SPI_TPM_CS# GND RSMRST# SPI_MISO SPI_CS0 SPI_DQ2

Este conector es compatible con el sistema SPI M�dulo de Plataforma Segura (TPM, en ingl�s), que puede almacenar de forma segura claves, certificados digitales, contrase�as y datos. Un sistema TPM tambi�n ayuda a aumentar la seguridad en la red, protege las identidades digitales y garantiza la integridad de la plataforma.

68

H510 Pro BTC+

1.5 Interruptores inteligentes
La placa base contiene dos conmutadores inteligentes: Bot�n Alimentaci�n y Restablecer.

Bot�n Alimentaci�n (PWRBTN1) (consulte la p�g. 1, n� 5)

El bot�n Alimentaci�n permite a los usuarios encender y apagar r�pidamente el sistema.

Bot�n Restablecer (RSTBTN1) (consulte la p�g. 1, n� 6)

El bot�n Restablecer permite a los usuarios restablecer r�pidamente el sistema.

Espa�ol

69

1 
       ASRock H510 Pro BTC+,       ASRock.                ASRock     .
         BIOS         .            - ASRock   .    ,    ,  -           .  - ASRock        VGA-  . - ASRock http://www.asrock.com.
1.1  
�   ASRock H510 Pro BTC+ �     ASRock H510 Pro BTC+ �     ASRock H510 Pro BTC+ � 1    Serial ATA (SATA) ( ) � 1    M.2 ( )
70



H510 Pro BTC+

1.2  

 �     



�   Gen Intel� CoreTM 10  

 Gen Intel� CoreTM 11  (LGA1200)

� Digi Power design

�   4

�   Intel� Turbo Boost Max 3.0



� Intel� H510



� 1 x  DDR4 DIMM
*    DRAM  2 . �     DDR4
3200/2933/2800/2666/2400/2133  ECC. *  11  Intel� CoreTM (i9/i7/i5)   DDR4    3200; CoreTM (i3), Pentium�  Celeron�
  DDR4    2666. *  10  Intel� CoreTM (i9/i7)   DDR4    2933; CoreTM (i5/i3), Pentium�  Celeron�
  DDR4    2666.
*     
  (Memory Support List )  - ASRock.
(http://www.asrock.com/) �    ECC UDIMM (  ,
  ) �   : 32  �  Intel� Extreme Memory Profile (XMP) 2.0

 

� 6 x  PCI Express 3.0 x16 (PCIE1  x16 / PCIE2~6  x1) � 1   (M_Port1  x1)*
*    USB

 

�   Intel� UHD Graphics  
VGA      
  . �  11  Intel� CoreTM 
  Intel� Xe ( 12).  10  Intel� CoreTM   9 



71

LAN

�  HDMI 1.4     4K � 2K (4096x2160)  30 
�  Auto Lip Sync, Deep Color (12 /), xvYCC  HBR (High Bit Rate Audio)   HDMI 1.4 (  HDMI-)
�  HDCP 2.3   HDMI 1.4.
� Gigabit Ethernet 10/100/1000 / � Giga PHY Intel� I219V �     �       �  Energy Efficient Ethernet 802.3az �  PXE

  -

� 1 x  PS/2  / � 1 x  HDMI � 2 x  USB 2.0 (    ) � 2 x  USB 3.2 Gen1 (   
) � 1 x   RJ-45   (/
 )

 

� 1  SATA3 6.0 /,  NCQ, AHCI  �� 
� 1  M.2,   M.2 SATA3     2260/2280/22110     6,0 /





� 1      � 1 x  SPI  � 1 x      
 � 1 x      (4-)
*      
    1  (12 ). � 8    , 4-
* CHA_FAN3~CHA_FAN8    
    2,5  (30 ).
* CPU_FAN1, CHA_FAN1  CHA_FAN2   
  4- . � 3   , 24- � 1   PCIe 12 , 8- � 4   PCIe, 4-

72

H510 Pro BTC+

� 1  USB 2.0 (2  USB 2.0    -
 ) � 1   � 1  

 BIOS
 

� AMI UEFI Legal BIOS     
�      ACPI 6.0 �  SMBIOS 2.7 �   / , GT, VCCSA, DRAM,
VCCIO, VCCIN AUX
� : CPU,   �   (   
     ): CPU,   �   : CPU,   �  : Vcore , +12 , +5 , +3,3 

 

� Microsoft� Windows� 10 (64-) � Linux: Ubuntu 16.04 LTS / Fedora 25 *     Linux O/S. -    Linux     .



� FCC, CE �   ErP/EuP (  , -
  ErP/EuP)

*         -: http://www.asrock.com

 ,   ,    BIOS,   Untied Overclocking      ,    .               .           .       ,   .



73

1.3  
    .   -    ��.  -    ,  ��.

   CMOS (CLRMOS1) (. . 1,  3)

2- 

CLRMOS1     CMOS.          ,          .  15        CLRMOS1  5 .    CMOS    BIOS.     CMOS    BIOS   ,        CMOS. ,  , ,           ,    CMOS.    CMOS     .



74

H510 Pro BTC+

1.4   ,    
         .        -.  -           .

   (9-, PANEL1) (. . 1,  10)

GND PWRBTN#
PLEDPLED+

GND RESET# GND HDLEDHDLED+ 1

     ,              ,  .        .

PWRBTN ( ):   ,     .         .
RESET ( ):   ,     .   ,   ,       .
PLED (   ):   ,     .   ,   .       S1/S3,  .       S4   (S5),   .
HDLED (    ):      ,    .   ,        .
       .      ,  ,  ,    ,   ..            .



75

       (7-, SPK_ PLED1) (. . 1,  11)

SPEAKER DUMMY DUMMY +5V

PLEDPLED+ PLED+
1

        .

 Serial ATA3  : (SATA_1: . .1,  13)

  SATA3      SATA          6,0 /.

 USB 2.0 (9-, USB_3_4) (. . 1,  9)

DUMMY GND P+ P-
USB_PWR

GND P+ PUSB_PWR 1

     .   USB 2.0    .

   (4-, CHA_ FAN1) (. . 1,  4)

4 3 21
FAN_SPEED_CONTROL CHA_FAN_SPEED FAN_VOLTAGE GND

           .

(4 , CHA_ FAN2) (. . 1,  12)

1

GND

2

FAN_VOLTAGE

3

CHA_FAN_SPEED

4

FAN_SPEED_CONTROL



76

H510 Pro BTC+

(4-, CHA_ FAN3) (. . 1,  26) (4-, CHA_ FAN4) (. . 1,  25) (4 , CHA_ FAN5) (. . 1,  17) (4 , CHA_ FAN6) (. . 1,  24) (4 , CHA_ FAN7) (. . 1,  20) (4 , CHA_ FAN8) (. . 1,  23)

4 3 21
FAN_SPEED_CONTROL CHA_FAN_SPEED +12V GND

    (4-, CPU_FAN1) (. . 1,  1)

FAN_SPEED_CONTROL CPU_FAN_SPEED
+12V GND
1 2 34

    4-     .     3-   ,     1-3.

   (24-, ATXPWR1) (. . 1,  8) (24-, ATXPWR2) (. . 1,  7) (24-, ATXPWR3) (. . 1,  21)

12

24

1

13

     24-   .   20-   ATX,     1   13.



77

   12  (8-, ATX12V1) (. . 1,  27)
  PCIe (4- PCIE_ PWR3) (. . 1,  16) (4- PCIE_ PWR4) (. . 1,  18) (4- PCIE_ PWR5) (. . 1,  19) (4- PCIE_ PWR6) (. . 1,  22)
  (M_Port1:. .1, 15)

5

1

8

4

    8-    12 .   4-   ATX,     1   5.
      .
 . ,  4-   PCIe           ;         .

       .

9 PERXN PERXP 8
GND 7 PETXP 6 PETXN 5

1 WAKE# 2 CLKN 3 CLKP 4 RST

 SPI  (13-, SPI_ TPM_J1) (. . 1,  14)

SPI_DQ3 +3.3V Dummy CLK SPI_MOSI RST# TPM_PIRQ
1
SPI_TPM_CS# GND RSMRST# SPI_MISO SPI_CS0 SPI_DQ2

     SPI Trusted Platform Module (TPM),      ,  ,   .       ,       .



78

H510 Pro BTC+

1.5 -
     -:      .

  (PWRBTN1) (. . 1,  5)

        .

  (RSTBTN1) (. . 1,  6)

      .



79

Portugu�s

1 Introdu��o
Obrigado por comprar a placa-m�e ASRock H510 Pro BTC+, uma placa-m�e confi�vel produzida sob o controle de qualidade altamente consistente da ASRock. Esta placa principal oferece um excelente desempenho com um design robusto em conformidade com o compromisso da ASRock em fabricar produtos de qualidade e resistentes.
Como as especifica�es da placa-m�e e do software do BIOS podem ser atualizadas, o conte�do desta documenta��o estar� sujeito a altera�es sem aviso pr�vio. Caso ocorram modifica�es a esta documenta��o, a vers�o atualizada estar� dispon�vel no site da ASRock sem aviso pr�vio. Se precisar de assist�ncia t�cnica relacionada a esta placa principal, visite o nosso site para obter informa�es espec�ficas sobre o modelo que estiver utilizando. Voc� tamb�m poder� encontrar a lista de placas VGA e CPU mais recentes suportadas no site da ASRock. Site da ASRock http://www.asrock.com.
1.1 Conte�do da embalagem
� Placa M�e ASRock H510 Pro BTC+ � Guia de Instala��o R�pida da ASRock H510 Pro BTC+ � CD de Suporte do ASRock H510 Pro BTC+ � 1 x Cabo de dados Serial ATA (SATA) (Opcional) � 1 x Parafuso para Soquete M.2 (Opcional)
80

H510 Pro BTC+

1.2 Especifica�es

Plataforma � Design de condensador s�lido

CPU

� Suporta Processadores de 10� Gen Intel� CoreTM e Processadores 11th Gen Intel� CoreTM (LGA1200)
� Digi Power design � Design com 4 fases de alimenta��o � Suporta Tecnologia Intel� Turbo Boost Max 3.0

Chipset

� Intel� H510

Mem�ria

� 1 x Slot DIMM DDR4 * 2GB de DRAM por m�dulo n�o � suportado. � Suporta mem�ria DDR4 3200/2933/2800/2666/2400/2133, n�o
ECC, sem mem�ria interm�dia* * 11� Gen Intel� CoreTM (i9/i7/i5) suporta DDR4 at� 3200; CoreTM (i3), Pentium� e Celeron� suporta DDR4 at� 2666. * 10� Gen Intel� CoreTM (i9/i7) suporta DDR4 at� 2933; CoreTM (i5/i3), Pentium� e Celeron� suportam DDR4 at� 2666. * Por favor, consulte a Lista de Suporte de Mem�ria no site da ASRock para obter mais informa��o. (http://www.asrock.com/) � Suporta m�dulos de mem�ria ECC UDIMM (opera em modo n�o-
ECC) � Capacidade m�xima da mem�ria do sistema: 32GB � Suporta Extreme Memory Profile (XMP) 2.0 da Intel�

Slot de expans�o

� 6 x Slots PCI Express 3.0 x16 (PCIE1 a x16 / PCIE2~6 a x1) � 1 x Porta de Mining (M_Porta1 a x1) * * Suporta kit Riser tipo USB

Gr�ficos

� Os gr�ficos incorporados Intel� UHD e as sa�das VGA s� podem ser suportados com processadores com GPU integrada.
� Processadores 11� Gen Intel� CoreTM suporta Arquitetura Gr�ficos Intel� Xe (Gen 12). Processadores 10� Gen Intel� CoreTM suportam Gr�ficos Gen 9

Portugu�s

81

� Suporta HDMI 1,4 com resolu��o m�x. at� 4K x 2K (4096x2160) @ 30Hz
� Suporta Auto sincroniza��o labial, Deep Color (12bpc), xvYCC e HBR (High Bit Rate Audio) com porta HDMI 1.4 (� necess�rio um monitor compat�vel com HDMI)
� Suporta HDCP 2.3 com Porta HDMI 1.4

LAN

� LAN Gigabit a 10/100/1000 Mb/s � Giga PHY Intel� I219V � Suporta Wake-On-LAN � Oferece Suporte � Prote��o de Rel�mpago/ESD � Suporta Energy Efficient Ethernet 802.3az � Suporta PXE

E/S do painel posterior

� 1 x Porta PS/2 para mouse/teclado � 1 x Porta HDMI � 2 x Portas USB 2.0 (Suporta Prote��o ESD) � 2 x Portas USB 3.2 Gen1 (Suporta Prote��o ESD) � 1 x Porta LAN RJ-45 com LED (LED ACT/LINK e LED DE
VELOCIDADE)

Armazenamento

� 1 x Conector SATA3 6,0 Gb/s, suporte NCQ, AHCI, Conector a Quente
� 1 x Soquete M.2 , suporta m�dulo Chave tipo 2260/2280/22110 M.2 SATA3 6,0 Gb/s

Conector

� 1 x Cabe�ote do Painel do Sistema � 1 x Plataforma SPI TPM � 1 x LED de alimenta��o e Cabe�ote de Autofalante � 1 x Conector da ventoinha da CPU (4 pinos)
* O Conector do Ventilador de CPU suporta o ventilador de CPU de
alimenta��o m�xima 1A do ventilador (12W). � 8 x Conectores da ventoinha do Gabinete (4 pinos)
* CHA_FAN3~CHA_FAN8 suporta o ventilador de chassis de alimen-
ta��o m�xima 2,5A do ventilador (30W).
* CPU_FAN1, CHA_FAN1 e CHA_FAN2 podem ajustar a velocidade
do ventilador de 4 pinos. � 3 x Conectores alimenta��o ATX 24 pinos � 1 x Conector principal de energia x 8-pinos PCIe 12V

Portugu�s

82

H510 Pro BTC+

Fun�es da BIOS

� 4 x Conectores Alimenta��o PCIe 4 pinos � 1 x Plataforma USB 2.0 (Suporta 2 portas USB 2.0) (Suporta Prote-
��o ESD) � 1 x bot�o Liga/Desliga � 1 x Bot�o de Reset
� AMI Legal UEFI BIOS com suporte multilingue GUI � ACPI 6.0 compat�vel com eventos de despertar � Suporte SMBIOS 2.7 � CPU Core/Cache, CPU GT, VCCSA, DRAM, VCCIO, VCCIN AUX
Multi-ajuste de Tens�o

Monitor de hardware

� Tac�metro da ventoinha: CPU, Ventoinha do Chassi � Ventoinha Silenciosa (Auto ajusta velocidade da ventoinha do chas-
si pela temperatura da CPU): CPU, Ventoinha do Chassi � Controle multi-velocidade da ventoinha: CPU, Ventoinha do Chassi � Monitoramento da tens�o: CPU Vcore, +12V, +5V, +3,3V

SO

� Microsoft� Windows� 10 64-bit

� Linux: Ubuntu 16.04 LTS / Fedora 25

* A fun��o b�sica do SO Linux confere, devido � compatibilidade do

pr�prio Sistema Linux, que n�o existe garantia que todas as fun�es

sejam suportadas.

Certifica�es

� FCC, CE � Preparada para ErP/EuP (� necess�ria uma fonte de alimenta��o
preparada para ErP/EuP)

* Para obter informa�es detalhadas sobre o produto, por favor, visite o nosso site: http://www.asrock.com

Por favor, observe que existe um certo risco envolvendo overclocking, incluindo o ajuste das defini�es na BIOS, a aplica��o de tecnologia Untied Overclocking ou a utiliza��o de ferramentas de overclocking de terceiros. O overclocking poder� afetar a estabilidade do sistema ou mesmo causar danos nos componentes e dispositivos do seu sistema. Ele deve ser realizado por sua conta e risco. N�o nos responsabilizamos por poss�veis danos causados pelo overclocking.

Portugu�s

83

1.3 Configura��o dos jumpers
A imagem abaixo mostra como os jumpers s�o configurados. Quando a tampa do jumper � colocada nos pinos, o jumper � "Curto". Se n�o for colocada uma tampa de jumper nos pinos, o jumper � "Aberto".

Apagar o Jumper CMOS (CLRMOS1) (ver p.1, N.� 3)

Jumper de 2 pinos

CLRMOS1 permite que voc� limpe os dados do CMOS. Para apagar e reinicializar os par�metros do sistema nos valores predefinidos, desligue o computador e desplugue a tomada da alimenta��o. Depois de aguardar 15 segundos, use uma capa de jumper para fazer curto dos pinos no CLRMOS1 por 5 segundos. No entanto, n�o apague o CMOS logo ap�s ter realizado a atualiza��o da BIOS. Se voc� precisar apagar o CMOS logo ap�s ter terminado uma atualiza��o da BIOS, dever� primeiro iniciar o sistema e voltar a encerr�lo antes de apagar o CMOS. Por favor, observe que a senha, data, hora e perfil padr�o do usu�rio ser�o apagados s� se a bateria CMOS for removida. Por favor, n�o se esque�a de retirar a tampa do jumper depois de apagar o CMOS.

Portugu�s

84

H510 Pro BTC+

1.4 Suportes e conectores onboard
Os conectores e suportes onboard N�O s�o jumpers. N�O coloque tampas de jumpers sobre estes terminais e conectores. Colocar tampas de jumpers sobre os terminais e conectores ir� causar danos permanentes � placa-m�e.

Suporte do painel de sistema (PAINEL1 de 9 pinos) (ver p.1, N.� 10)

GND PWRBTN#
PLEDPLED+

GND RESET# GND HDLEDHDLED+ 1

Ligue o bot�o de alimenta��o, o bot�o de reinicializa��o e o indicador do estado do sistema no chassi deste suporte, de acordo com a descri��o abaixo. Observe os pinos positivos e negativos antes de conectar os cabos.

PWRBTN (Bot�o de alimenta��o): Conecte o bot�o de alimenta��o no painel frontal do chassi. Voc� pode configurar a forma para desligar o seu sistema atrav�s do bot�o de alimenta��o.
RESET (Bot�o de reinicializa��o): Conecte o bot�o de reinicializa��o no painel frontal do chassi. Pressione o bot�o de reinicializa��o para reiniciar o computador, se ele congela e falha ao realizar um rein�cio normal.
PLED (LED de alimenta��o do sistema): Conecte o indicador do estado da alimenta��o no painel frontal do chassi. O LED ficar� aceso quando o sistema estiver em funcionamento. O LED ficar� piscando quando o sistema estiver nos estados de suspens�o S1/S3. O LED ficar� desligado quando o sistema estiver no estado de suspens�o S4 ou desligado (S5).
HDLED (LED de atividade do disco r�gido): Conecte o LED de atividade do disco r�gido no painel frontal do chassi. O LED ficar� aceso quando o disco r�gido estiver lendo ou registrando dados.
O design do painel frontal poder� variar dependendo do chassi. Um m�dulo de painel frontal consiste principalmente em um bot�o de alimenta��o, um bot�o de reinicializa��o, um LED de alimenta��o, um LED de atividade do disco r�gido, um alto-falante, etc. Ao conectar seu m�dulo de painel frontal do chassi a este conector, certifique-se de que os fios e os pinos correspondem de forma correta.

Portugu�s

85

LED de alimenta��o e Cabe�ote de Autofalante (SPK_PLED1 de 7 pinos) (ver p.1, N.� 11)

SPEAKER DUMMY DUMMY +5V

PLEDPLED+ PLED+
1

Conecte o LED de alimenta��o do chassi e o autofalante do chassi a este cabe�ote.

Conector Serial ATA3 �ngulo reto: (SATA_1: ver p.1, N.� 13)
Suporte USB 2.0 (USB_3_4 de 9 pinos) (ver p.1, N.� 9)

Este conector SATA3 suporta cabos de dados SATA para dispositivos de armazenamento interno com uma taxa de transfer�ncia de dados de at� 6.0 Gb/s.

DUMMY GND P+ P-
USB_PWR

GND P+ PUSB_PWR 1

H� um cabe�ote nesta placa-m�e. Cada suporte USB 2.0 pode ter duas portas.

Conectores da Ventoinha do Chassi (CHA_FAN1 de 4 pinos) (ver p.1, N.� 4)

4 3 21
FAN_SPEED_CONTROL CHA_FAN_SPEED FAN_VOLTAGE GND

Por favor, conecte os cabos do ventilador aos conectores do ventilador e corresponda o fio preto no pino terra.

(CHA_FAN2 de 4 pinos) 1

2

(ver p.1, N.� 12)

3

4

GND FAN_VOLTAGE CHA_FAN_SPEED FAN_SPEED_CONTROL

Portugu�s

86

H510 Pro BTC+

(CHA_FAN3 de 4 pinos) (ver p.1, N.� 26) (CHA_FAN4 de 4 pinos) (ver p.1, N.� 25) (CHA_FAN5 de 4 pinos) (ver p.1, N.� 17) (CHA_FAN6 de 4 pinos) (ver p.1, N.� 24) (CHA_FAN7 de 4 pinos) (ver p.1, N.� 20) (CHA_FAN8 de 4 pinos) (ver p.1, N.� 23)

4 3 21
FAN_SPEED_CONTROL CHA_FAN_SPEED +12V GND

Conector da Ventoinha da CPU (CPU_FAN1 de 4 pinos) (ver p.1, N.� 1)

FAN_SPEED_CONTROL CPU_FAN_SPEED
+12V GND
1 2 34

Esta placa m�e inclui um conector de ventilador da CPU (Ventilador silencioso) de 4 pinos. Se voc� pretende conectar um ventilador da CPU de 3 pinos, por favor, conecte-o ao Pino 1-3.

Conectores de alimenta��o ATX (ATXPWR1 de 24 pinos) (ver p.1, N.� 8) (ATXPWR2 de 24 pinos) (ver p.1, N.� 7) (ATXPWR3 de 24 pinos) (ver p.1, N.� 21)
Conector de alimenta��o de 12V ATX (ATX12V1 de 8 pinos) (ver p.1, N.� 27)

12

24

1

13

5

1

8

4

Esta placa-m�e inclui tr�s conectores de alimenta��o de ATX de 24 pinos. Para utilizar uma fonte de alimenta��o ATX de 20 pinos, introduza-a no Pino 1 e Pino 13.
Esta placa-m�e inclui um conector de alimenta��o de 12V ATX de 8 pinos. Para utilizar uma fonte de alimenta��o ATX de 4 pinos, introduza-a no Pino 1 e Pino 5.

Portugu�s

87

Conectores de Energia PCIe (PCIE_PWR3 de 4 pinos) (ver p.1, N.� 16) (PCIE_PWR4 de 4 pinos) (ver p.1, N.� 18) (PCIE_PWR5 de 4 pinos) (ver p.1, N.� 19) (PCIE_PWR6 de 4 pinos) (ver p.1, N.� 22)

Conecte esses conectores �s fontes de alimenta��o.
Importante: Verifique se o conector de alimenta��o PCIe de 4 pinos e conector de alimenta��o externa na placa de v�deo est�o conectados � mesma fonte de alimenta��o; caso contr�rio, a placa-m�e e placa de v�deo podem ser danificadas.

Porta Mining (M_Port1:ver p.1, N.� 15)

Conecte esta porta ao kit do elevador.

9 PERXN PERXP 8
GND 7 PETXP 6 PETXN 5

1 WAKE# 2 CLKN 3 CLKP 4 RST

Plataforma SPI TPM (SPI_TPM_J1 de 13 pinos) (ver p.1, N.� 14)

SPI_DQ3 +3.3V Dummy CLK SPI_MOSI RST# TPM_PIRQ
1
SPI_TPM_CS# GND RSMRST# SPI_MISO SPI_CS0 SPI_DQ2

Este conector suporta um sistema com SPI M�dulo de Plataforma Confi�vel (TPM), que pode armazenar com seguran�a chaves, certificados digitais, senhas e dados. Um sistema TPM tamb�m ajuda a melhorar a seguran�a de rede, a proteger identidades digitais e a garantir a integridade da plataforma.

Portugu�s

88

H510 Pro BTC+

1.5 Interruptores inteligentes
A placa-m�e tem duas chaves inteligentes: Bot�o de Energia e Bot�o de Reinicializa��o.

Bot�o de alimenta��o (PWRBTN1) (ver p.1, N.� 5)

O Bot�o de alimenta��o permite aos usu�rios ligar/desligar o sistema rapidamente.

Bot�o Reset (Reiniciar) (RSTBTN1) (ver p.1, N.� 6)

O Bot�o Reset permite aos usu�rios reinicializar o sistema rapidamente.

Portugu�s

89

Polski

1 Wprowadzenie
Dzikujemy za zakupienie plyty gl�wnej ASRock H510 Pro BTC+, niezawodnej plyty gl�wnej produkowanej z konsekwentnie wykonywan przez firm ASRock, rygorystyczn kontrol jakoci. Plyta ta zapewnia doskonal jako dzialania i solidn konstrukcj, spelniajc zobowizanie firmy ASRock do dostarczania produkt�w o wysokiej jakoci i wytrzymaloci.
Poniewa specyfikacje plyty gl�wnej i oprogramowanie BIOS mog zosta zaktualizowane, zawarto tej dokumentacji moe zosta zmieniona bez powiadomienia. W przypadku jakichkolwiek modyfikacji tej dokumentacji, zaktualizowana wersja bdzie dostpna na stronie internetowej ASRock, bez dalszego powiadomienia. Jeli wymagana jest pomoc techniczna w odniesieniu do tej plyty gl�wnej, naley odwiedzi stron internetow w celu uzyskania specyficznych informacji o uywanym modelu. Na stronie internetowej ASRock, mona take pobra list najnowszych kart VGA i obslugiwanych CPU. Strona internetowa ASRock http://www.asrock.com.
1.1 Zawarto opakowania
� Plyta gl�wna ASRock H510 Pro BTC+ � Skr�cona instrukcja instalacji ASRock H510 Pro BTC+ � Pomocnicza plyta CD ASRock H510 Pro BTC+ � 1 x kabel danych Serial ATA (SATA) (Opcjonalne) � 1 x ruba do gniazda M.2 (opcjonalna)
90

H510 Pro BTC+

1.2 Specyfikacje

Platforma

� Konstrukcja kondensatorami stalymi

CPU

� Obsluga 10-tej generacji procesor�w Intel� CoreTM i 11-tejgeneracji procesor�w Intel� CoreTM (LGA1200)
� Digi Power design � Sekcja zasilania 4 Power Phase Design � Obsluga technologii Intel� Turbo Boost Max 3.0

Chipset

� Intel� H510

Pami

� 1 x gniazdo DDR4 DIMM
* 2GB DRAM na modul nie s obslugiwane. � Obsluga pamici DDR4 3200/2933/2800/2666/2400/2133 non-
ECC, pami niebuforowana * 11-tej generacji Intel� CoreTM (i9/i7/i5) obsluguj DDR4 do 3200; CoreTM (i3), Pentium� i Celeron� obsluguj DDR4 do 2666. * 10-tej generacji Intel� CoreTM (i9/i7) obsluguj DDR4 do 2933; CoreTM (i5/i3), Pentium� i Celeron� obsluguj DDR4 do 2666.
* Sprawd list obslugiwanej pamici na stronie internetowej ASRock
w celu uzyskania dalszych informacji. (http://www.asrock.com/) � Obsluga modul�w pamici ECC UDIMM (dzialanie w trybie non-
ECC) � Maks. wielko pamici systemowej: 32GB � Obsluga Intel� Extreme Memory Profile (XMP) 2.0

Gniazdo rozszerzenia

� 6 x gniazdo PCI Express x16 (PCIE1 w x16 / PCIE2~6 w x1) � 1 x porty do kopania kryptowalut (M_Port1 w x1)*
* Obsluga zestawu Riser typu USB

Grafika

� Wbudowana grafika Intel� UHD i wyjcia VGA s obslugiwane wylcznie z procesorami, kt�re maj zintegrowane GPU.
� 11-tej generacji procesory Intel� CoreTM obsluguj Intel� Xe Graphics Architecture (generacja 12). 10-tej generacji procesory Intel� CoreTM obsluguj grafik generacji 9

Polski

91

� Obsluga HDMI 1,4 z maks. rozdzielczoci do 4K x 2K (4096x2160) przy 30Hz
� Obsluga Auto Lip Sync, Deep Color (12bpc), xvYCC i HBR (High Bit Rate Audio) z portami HDMI 1.4 (Wymagany monitor zgodny z HDMI)
� Obsluga HDCP 2.3 z portem HDMI 1.4

LAN

� Gigabit LAN 10/100/1000 Mb/s � Giga PHY Intel� I219V � Obsluga Wake-On-LAN � Obsluga zabezpieczenia przed wyladowaniami atmosferycznymi/
ESD � Obsluga Energy Efficient Ethernet 802.3az � Obsluga PXE

Tylny panel Wejcia/Wyjcia

� 1 x port myszy/klawiatury PS/2 � 1 x port HDMI � 2 x porty USB 2.0 (Obsluga zabezpieczenia ESD) � 2 x porty USB 3.2 Gen1 (Obsluga zabezpieczenia ESD) � 1 x port LAN RJ-45 z LED (LED ACT/LINK i LED SPEED)

Przechowywanie

� 1 x zlcze SATA3 6,0 Gb/s, obsluga NCQ, AHCI i Hot Plug � 1 x gniazdo M.2, obsluga Key M typu 2260/2280/22110 modulu M.2
SATA3 6,0 Gb/s

Zlcze

� 1 x zlcze gl�wkowe na panelu systemu � 1 x zlcze gl�wkowe SPI TPM � 1 x dioda LED zasilania i zlcze gl�wkowe glonika � 1 x zlcze wentylatora CPU (4-pinowe) * Zlcze wentylatora CPU obsluguje wentylator CPU maksymalnym prdem zasilania wentylatora 1A (12W). � 8 x zlcze wentylatora obudowy (4-pinowe) * CHA_FAN3~CHA_FAN8 obsluguje wentylator obudowy z maksymalnym prdem zasilania wentylatora 2,5A (30W). * CPU_FAN1, CHA_FAN1 i CHA_FAN2 moe dostosowa prdko wentylatora 4-pinowego.

Polski

92

H510 Pro BTC+

Polsk i

� 3 x 24 pinowe zlcze zasilania ATX � 1 x 8 pinowe zlcze zasilania PCIe 12 V � 4 x 4 pinowe zlcze zasilania PCIe � 1 x zlcza gl�wkowe USB 2.0 (obsluguje 2 porty USB 2.0) (Obsluga
zabezpieczenia ESD) � 1 x Przycisk zasilania � 1 x Przycisk resetowania

Funkcja BIOS

� Obsluga starszych wersji BIOS AMI UEFI z wielojzycznym GUI � Zgodno zdarze wybudzania z ACPI 6.0 � Obsluga SMBIOS 2.7 � Wiele regulacji napicia CPU Core/Cache, CPU GT, VCCSA,
DRAM, VCCIO, VCCIN AUX

Monitor sprztu

� Obrotomierz wentylatora: CPU, Zlcza wentylatora obudowy � Cichy wentylator (Automatyczna regulacja prdkoci obrotowej
wentylatora obudowy przez temperatur CPU): CPU, Zlcza wentylatora obudowy � Kontrola wielu prdkoci obrotowych wentylatora: CPU, Zlcza wentylatora obudowy � Monitorowanie napicia: Napicie rdzenia CPU Vcore +12 V, +5 V, +3,3 V

System operacyjny

� Microsoft� Windows� 10 64-bitowy � Linux: Ubuntu 16.04 LTS / Fedora 25 * Obslugiwana wylcznie podstawowa funkcja systemu operacyjnego Linux, z powodu kompatybilnoci samego systemu Linux, nie gwarantuje si obslugi wszystkich funkcji.

Certyfikaty

� FCC, CE � Gotowo do obslugi ErP/EuP (Wymagane zasilanie z gotowoci
obslugi ErP/EuP)

* Dla uzyskania szczeg�lowej informacji o produkcie, naley odwiedzi nasz stron internetow: http://www.asrock.com

Naley pamita, e przetaktowywanie jest zwizane z pewnym ryzykiem, wlcznie z regulacj ustawie w BIOS, zastosowaniem Untied Overclocking Technology lub uywaniem narzdzi przetaktowywania innych firm. Przetaktowywanie moe wplywa na stabilno systemu lub nawet powodowa uszkodzenie komponent�w i urzdze systemu. Powinno to zosta zrobione na wlasne ryzyko i koszt. Nie odpowiadamy za moliwe uszkodzenia spowodowane przetaktowywaniem.
93

1.3 Ustawienia zworek
Ta ilustracja pokazuje ustawienia zworek. Po umieszczeniu nasadki zworki na pinach, zworka jest "Zwarta". Jeli nasadka zworki nie jest umieszczona na pinach, zworka jest "Otwarta".

Zworka usuwania danych z pamici CMOS (CLRMOS1) (sprawd s.1, Nr 3)

2-pinowa zworka

CLRMOS1 umoliwia usunicie wszystkich danych z pamici CMOS. Aby usun i zresetowa parametry systemu do ustawie domylnych, wylcz komputer i odlcz przew�d zasilajcy od zasilania. Po odczekaniu 15 sekund, uyj nasadk zworki do zwarcia pin�w CLRMOS1 na 5 sekund. Jednak, nie naley usuwa danych z pamici CMOS zaraz po wykonaniu aktualizacji BIOS. Jeli wymagane jest usunicie danych z pamici CMOS po zakoczeniu aktualizacji BIOS, przed rozpoczciem usuwania danych z pamici CMOS naley najpierw uruchomi system, a nastpnie wylczy go. Naley pamita, e haslo, data, czas i domylny profil uytkownika zostan usunite tylko po wyjciu baterii CMOS. Naley pamita, aby po usuniciu danych z pamici CMOS, usun nasadk zworki.

Polski

94

H510 Pro BTC+

1.4 Wbudowane zlcza gl�wkowe i inne zlcza
Wbudowane zlcza gl�wkowe i inne zlcza s bezzworkowe. NIE naley umieszcza zworek nad tymi zlczami gl�wkowymi i zlczami. Umieszczanie zworek nad zlczami gl�wkowymi i zlczami spowoduje trwale uszkodzenie plyty gl�wnej.

Zlcze gl�wkowe na panelu systemu (9-pinowe PANEL1) (sprawd s.1, Nr 10)

GND PWRBTN#
PLEDPLED+

GND RESET# GND HDLEDHDLED+ 1

Do tego zlcza gl�wkowego mona podlcza przycisk zasilania, przycisk reset i wskanik stanu systemu na obudowie, zgodnie z przydzialem pin�w poniej. Przed podlczeniem kabli naley zapisa pozycj pin�w plus i minus.

PWRBTN (Przycisk zasilania): Podlczenie do przycisk�w zasilania na panelu przednim obudowy. Uytkownik moe skonfigurowa spos�b wylczania systemu z uyciem przycisku zasilania.
RESET (Przycisk resetowania): Podlczenie do przycisku resetowania na panelu przednim obudowy. Nacinij przycisk resetowania, aby ponownie uruchomi komputer, przy jego zawieszeniu i braku moliwoci wykonania normalnego ponownego uruchomienia.
PLED (Dioda LED zasilania systemu): Podlczenie do wskanika stanu zasilania na panelu przednim obudowy. Ta dioda LED jest wlczona podczas dzialania systemu. Ta dioda LED miga, gdy system znajduje si w stanie upienia S1/S3. Ta dioda LED jest wylczona, gdy system znajduje si w stanie upienia S4 lub wylczenia zasilania (S5).
HDLED (Dioda LED aktywnoci dysku twardego): Podlczenie do diody LED aktywnoci dysku twardego na panelu przednim obudowy. Dioda LED jest wlczona, podczas odczytu lub zapisu danych przez dysk twardy.
Konstrukcja panelu przedniego zaley od obudowy. Modul panelu przedniego gl�wnie sklada si z przycisku zasilania, przycisku resetowania, diody LED zasilania, diody LED aktywnoci dysku twardego, glonika, itd. Po podlczeniu do tego zlcza gl�wkowego modulu panelu przedniego obudowy, naley si upewni, e jest prawidlowo dopasowany przydzial przewod�w i pin�w.

Polski

95

Dioda LED zasilania i zlcze gl�wkowe glonika (7-pinowe SPK_PLED1) (sprawd s.1, Nr 11)

SPEAKER DUMMY DUMMY +5V

PLEDPLED+ PLED+
1

Podlcz to tego zlcza gl�wkowego diod LED zasilania obudowy i glonik obudowy .

Zlcze Serial ATA3 Kt prosty: (SATA_1: sprawd s.1, Nr 13)

To zlcze SATA3 obsluguj kable danych SATA dla wewntrznych urzdze pamici z szybkoci transferu danych do 6,0 Gb/s.

Zlcza gl�wkowe USB 2.0 (9-pinowe USB_3_4) (sprawd s.1, Nr 9)

DUMMY GND P+ P-
USB_PWR

GND P+ PUSB_PWR 1

Na tej plycie gl�wnej znajduje si jedno zlcze gl�wkowe. Zlcze gl�wkowe USB 2.0 moe obslugiwa dwa porty.

Zlcza wentylatora obudowy (4-pinowe CHA_FAN1) (sprawd s.1, Nr 4)

4 3 21
FAN_SPEED_CONTROL CHA_FAN_SPEED FAN_VOLTAGE GND

Podlcz przewody wentylatora do zlczy wentylatora i dopasuj czarny przew�d do styku masy.

1

(4-pinowe CHA_FAN2)

2

3

(sprawd s.1, Nr 12)

4

GND FAN_VOLTAGE CHA_FAN_SPEED FAN_SPEED_CONTROL

Polski

96

H510 Pro BTC+

(4-pinowe CHA_FAN3) (sprawd s.1, Nr 26) (4-pinowe CHA_FAN4) (sprawd s.1, Nr 25) (4-pinowe CHA_FAN5) (sprawd s.1, Nr 17) (4-pinowe CHA_FAN6) (sprawd s.1, Nr 24) (4-pinowe CHA_FAN7) (sprawd s.1, Nr 20) (4-pinowe CHA_FAN8) (sprawd s.1, Nr 23)

4 3 21
FAN_SPEED_CONTROL CHA_FAN_SPEED +12V GND

Zlcze wentylatora CPU (4-pinowe CPU_FAN1) (sprawd s.1, Nr 1)
Zlcza zasilania ATX (24-pinowe ATXPWR1) (sprawd s.1, Nr 8) (24-pinowe ATXPWR2) (sprawd s.1, Nr 7) (24-pinowe ATXPWR3) (sprawd s.1, Nr 21)
Zlcze zasilania ATX 12V (8-pinowe ATX12V1) (sprawd s.1, Nr 27)

FAN_SPEED_CONTROL CPU_FAN_SPEED
+12V GND
1 2 34

Ta plyta gl�wna udostpnia 4-pinowe zlcze wentylatora CPU (Cichy wentylator). Jeli planowane jest podlczenie 3-pinowego wentylatora CPU, naley je podlczy do pin�w 1-3.

12

24

1

13

Ta plyta gl�wna udostpnia trzy 24-pinowe zlcza zasilania ATX. W celu uycia 20-pinowego zasilacza ATX, naley podlczy je wzdlu pinu 1 i pinu 13.

5

1

Ta plyta gl�wna udostpnia

8-pinowe zlcze zasilania ATX

12 V. W celu uycia 4-pinowego

zasilacza ATX, naley podlczy

8

4

je wzdlu pinu 1 i pinu 5.

Polski

97

Zlcza zasilania PCIe (4-pinowe PCIE_PWR3) (sprawd s.1, Nr 16) (4-pinowe PCIE_PWR4) (sprawd s.1, Nr 18) (4-pinowe PCIE_PWR5) (sprawd s.1, Nr 19) (4-pinowe PCIE_PWR6) (sprawd s.1, Nr 22)

Podlcz te zlcza do zasilacza.
Wane: Upewnij si, czy 4-pinowe zlcze zasilania PCIe i zlcze zasilania zewntrznego karty graficznej s podlczone do tego samego zasilacza; w przeciwnym razie moe doj do uszkodzenia plyty gl�wnej i karty graficznej.

Porty do kopania kryptowalut (M_Port1:sprawd s.1, Nr 15)

9 PERXN PERXP 8
GND 7 PETXP 6 PETXN 5

1 WAKE# 2 CLKN 3 CLKP 4 RST

Podlcz ten port do zestawu rozszerze.

zlcze gl�wkowe SPI TPM (13-pinowe SPI_TPM_J1) (sprawd s.1, Nr 14)

SPI_DQ3 +3.3V Dummy CLK SPI_MOSI RST# TPM_PIRQ
1
SPI_TPM_CS# GND RSMRST# SPI_MISO SPI_CS0 SPI_DQ2

To zlcze obsluguje system SPI Trusted Platform Module (TPM), kt�ry moe bezpiecznie przechowywa klucze, certyfikaty cyfrowe, hasla i dane. System TPM pomaga take w zwikszeniu zabezpieczenia sieci, ochronie cyfrowych danych osobowych i zapewnieniu integralnoci platformy.

Polski

98

H510 Pro BTC+

1.5 Inteligentne przelczniki
Plyta gl�wna ma dwa inteligentne przelczniki: przycisk zasilania i przycisk resetowania

Przycisk zasilania (PWRBTN1) (sprawd s.1, Nr 5)

Przycisk zasilania umoliwia uytkownikom szybkie wlczanie/ wylczanie systemu.

Przycisk resetowania (RSTBTN1) (sprawd s.1, Nr 6)

Przycisk resetowania umoliwia uytkownikom szybkie resetowanie systemu.

Polski

99

  

1 
ASRock H510 Pro BTC+     .   ASRock         .    ASRock         .
  BIOS      ,         .     ,    ASRock       .         ,            . ASRock    VGA   CPU      . ASRock  http://www.asrock.com.
1.1  
� ASRock H510 Pro BTC+  � ASRock H510 Pro BTC+    � ASRock H510 Pro BTC+  CD �  ATA (SATA)   1  (   ) � M.2   1  (   )
100



H510 Pro BTC+

1.2 
 CPU
 
  

�   
� 10th Gen Intel� CoreTM   11th Gen Intel� CoreTM   (LGA1200) 
� Digi Power design � 4     � Intel� Turbo Boost Max Technology 3.0 
� Intel� H510
� DDR4 DIMM  1  *  2GB DRAM    . � DDR4 3200/2933/2800/2666/2400/2133  ECC,  
 * 11th Gen Intel� CoreTM(i9/i7/i5)  DDR4  3200  , CoreTM(i3), Pentium�  Celeron�  DDR4  2666   . * 10th Gen Intel� CoreTM(i9/i7)  DDR4  2933  , CoreTM (i5/ i3), Pentium�  Celeron�  DDR4  2666   . *    ASRock        . (http://www.asrock.com/) � ECC UDIMM   (  -ECC   )  �     : 32GB � Intel� Extreme Memory Profile (XMP) 2.0 
� PCI Express 3.0 x16  6  (PCIE1 @ x16 / PCIE2~6 @ x1) �   1  (x1  M_Port1)* * USB    
� Intel� UHD   -   VGA  GPU       .
� 11th Gen Intel� CoreTM  Intel� Xe Graphics Architecture(Gen 12)   . 10th Gen Intel� CoreTM   Gen 9 Graphics   .
� HDMI 1.4  (   4K x 2K (4096x2160) @ 30Hz) � Auto Lip Sync, Deep Color (12bpc), xvYCC  HBR (High Bit Rate
Audio)(HDMI 1.4   )  (HDMI    ) � HDMI 1.4   HDCP 2.3 

101

  

LAN

� Gigabit LAN 10/100/1000 Mb/s � Giga PHY Intel� I219V � Wake-On-LAN  �  /ESD   �   802.3az  � PXE 

  I/O

� PS/2  /   1  � HDMI  1  � USB 2.0  2  (ESD   ) � USB 3.2 Gen1  2  (ESD   ) � LED  RJ-45 LAN  1  (ACT/LINK LED  SPEED LED)

 

� SATA3 6.0 Gb/s  1  , NCQ, AHCI  " "  
� M.2  1  , M   2260/2280/22110 M.2 SATA3 6.0 Gb/s  



�    1  � SPI TPM  1  �  LED    1  � CPU   (4  ) 1  * CPU      1A(12W)  CPU  
 . �    8  (4  ) * CHA_FAN3~CHA_FAN8     2.5A(30W)   
  .
* CPU_FAN1, CHA_FAN1  CHA_FAN2  4    
  . � 24  ATX   3  � 8  PCIe 12V   1  � 4  PCIe   4  � USB 2.0  1  (USB 2.0  2   ) (ESD   ) �   1  �   1 

102

H510 Pro BTC+

BIOS 

�  GUI   AMI UEFI  BIOS � ACPI 6.0     � SMBIOS 2.7  � CPU Core/Cache, CPU GT, VCCSA, DRAM, VCCIO, VCCIN AUX
  

  

�   : CPU,  �   (CPU        ): CPU, 

�     : CPU,  �   : CPU Vcore, +12V, +5V, +3.3V

OS

� Microsoft� Windows� 10 64- 

� Linux: Ubuntu 16.04 LTS/Fedora 25

* Liunx     Linux O/S    .

     .



� FCC, CE � ErP/EuP   (ErP/EuP     )

*        : http://www.asrock.com
BIOS   Untied Overclocking Technology                  .                .          .            .



103

1.3  
     .     ""  .       "" .

Clear CMOS  (CLRMOS1) (1  , 3    )

2  

CLRMOS1   CMOS       .            
  . 15        CLRMOS1   5    .  BIOS   CMOS    . BIOS    CMOS     ,          CMOS     . CMOS     ,  ,  ,     . CMOS        .

  

104

H510 Pro BTC+

1.4    
     .        .           .

   (9  PANEL1) (1  , 10    )

GND PWRBTN#
PLEDPLED+

GND RESET# GND HDLEDHDLED+ 1

   ,   ,            .           .

PWRBTN(   ):       .          .
RESET(   ):       .              .
PLED(   LED):        .     LED    .  S1/S3     LED    .   S4      (S5)    LED    .
HDLED(    LED):       LED   .        LED    .
       .       ,   ,  LED,    LED,     .                .



105

  

 LED    (7  SPK_PLED1) (1  , 11    )

SPEAKER DUMMY DUMMY +5V

PLEDPLED+ PLED+
1

  LED        .

 ATA3    : (SATA_1: 1  , 13    )

 SATA3   6.0 Gb/ s        SATA    .

USB 2.0  (9  USB_3_4) (1  , 9    )

DUMMY GND P+ P-
USB_PWR

GND P+ PUSB_PWR 1

      .  USB 2.0        .

   (4  CHA_FAN1) (1  , 4    )

4 3 21
FAN_SPEED_CONTROL CHA_FAN_SPEED FAN_VOLTAGE GND

           .

1

(4  CHA_FAN2)

2

3
(1  , 12    4

)

GND FAN_VOLTAGE CHA_FAN_SPEED FAN_SPEED_CONTROL

106



H510 Pro BTC+

(4  CHA_FAN3) (1  , 26    ) (4-  CHA_FAN4) (1  , 25    ) (4  CHA_FAN5) (1  , 17    ) (4  CHA_FAN6) (1  , 24    ) (4  CHA_FAN7) (1  , 20    ) (4  CHA_FAN8) (1  , 23    )
CPU   (4  CPU_FAN1) (1  , 1    )

4 3 21
FAN_SPEED_CONTROL CHA_FAN_SPEED +12V GND

FAN_SPEED_CONTROL CPU_FAN_SPEED
+12V GND
1 2 34

  4  CPU  (   )     . 3  CPU      1-3    .

ATX   (24  ATXPWR1) (1  , 8    ) (24  ATXPWR2) (1  , 7    ) (24  ATXPWR3) (1  , 21    )

12

24

1

13

  24  ATX         . 20  ATX     1   13    .

107

ATX 12V   (8  ATX12V1) (1  , 27    )

5

1

8

4

  8  ATX 12V      . 4  ATX     1   5    .

  

PCIe   (4  PCIE_PWR3) (1  , 16    ) (4  PCIE_PWR4) (1  , 18    ) (4  PCIE_PWR5) (1  , 19    ) (4  PCIE_PWR6) (1  , 22    )
  (M_Port1:1  ,15    )
9 PERXN PERXP 8
GND 7 PETXP 6
PETXN 5

1 WAKE# 2 CLKN 3 CLKP 4 RST

     .   : 4  PCIe          PSU     .           .
      .

SPI TPM  (13  SPI_TPM_J1) (1  , 14    )

SPI_DQ3 +3.3V Dummy CLK SPI_MOSI RST# TPM_PIRQ
1
SPI_TPM_CS# GND RSMRST# SPI_MISO SPI_CS0 SPI_DQ2

   ,   ,         SPI TPM(Trusted Platform Module)    . TPM      ,         .

108

H510 Pro BTC+

1.5  
   2    :      .

  (PWRBTN1) (1  , 5    )

        .

  (RSTBTN1) (1  , 6    )

       .



109



1 
ASRock H510 Pro BTC+  ASRock  
 BIOS   ASRock    ASRock  VGA  CPU  ASRock  http://www.asrock.com.
1.1 
� ASRock H510 Pro BTC+  � ASRock H510 Pro BTC+  � ASRock H510 Pro BTC+  CD �  ATASATAx1 � 1 x M.2 
110



H510 Pro BTC+

1.2 
 � 

CPU

�  10  Intel� CoreTM  11 Gen Intel� CoreTM  (LGA1200) 
�  � 4  � Intel�  Max  3.0 



� Intel� H510

 

� 1 x DDR4 DIMM  *  2GB DRAM  � DDR4 3200/2933/2800/2666/2400/2133  ECC
 *  11  Intel� CoreTM (i9/i7/i5)  3200  DDR4 CoreTM (i3)Pentium�  Celeron�  2666  DDR4  *  10  Intel� CoreTM (i9/i7)  2933  DDR4  CoreTM (i5/i3)Pentium�  Celeron�  2666  DDR4  * ASRock  (http://www.asrock.com/) � ECC UDIMM non-ECC 
 � 32GB � Intel� XMP2.0 
� 6 x PCI Express 3.0 x16 x16  PCIE1/x1  PCIE2  6 � 1 x  M_Port1 @ x1* * USB 



� Intel� UHD  VGA  GPU 
�  11  Intel� CoreTM Intel� Xe   (Gen 12)  10  Intel� CoreTM Gen 9 

111



� HDMI 1.4  4K x 2K (4096x2160) @ 30Hz
� HDMI 1.4 12bpc xvYCCHBRHDMI
 � HDMI 1.4  HDCP 2.3 

LAN

�  LAN 10/100/1000 Mb/s �  PHY Intel� I219V � Wake-On-LAN   �  /  (ESD)  �  802.3az  � PXE 

 I/O

� 1 x PS/2  /  � 1 x HDMI  � 2 x USB 2.0  (ESD)  � 2 x USB 3.2 Gen1  (ESD)  � LED  1 x RJ-45 LAN ACT/LINK LED  SPEED
LED



� 1 x SATA3 6.0 Gb/s NCQAHCI 
� 1 x M.2 M Key  2260/2280/22110 M.2 SATA3 6.0 Gb/s 



� 1 x  � 1 x SPI TPM  � 1 x  LED  � 1 x CPU 4  * CPU  1A (12W)  CPU 
 � 8 x 4  * CHA_FAN3~CHA_FAN8  2.5A (30W) 

* CPU_FAN1CHA_FAN1CHA_FAN2  4 
 � 3 x 24  ATX  � 1 x 8  PCIe 12V 

112



H510 Pro BTC+

BIOS 

� 4 x 4  PCIe  � 1 x USB 2.0 2  USB 2.0 
ESD � 1 x  � 1 x 
� AMI UEFI Legal BIOS GUI  � ACPI 6.0  � SMBIOS 2.7  � CPU  / CPU GTVCCSADRAMVCCIO
VCCIN AUX 

 

�  : CPU,  � CPU :
CPU,  �  : CPU,  �  : CPU Vcore+12V+5V+3.3V

OS

� Microsoft� Windows� 10 64-bit

� Linux: Ubuntu 16.04 LTS / Fedora 25

* Linux O/S Linux 







� FCCCE � ErP/EuP Ready ErP/EuP 

* http://www.asrock.com
BIOS      

113

1.3 
  

CMOS  (CLRMOS1) p.1No. 3 

2 

CLRMOS1  CMOS   15  CLRMOS1  5 BIOS CMOS  BIOS CMOS   CMOS  CMOS  CMOS  



114



H510 Pro BTC+

1.4 
  

 9  PANEL1 p.1No. 10 

GND PWRBTN#
PLEDPLED+

GND RESET# GND HDLEDHDLED+ 1

      

PWRBTN  
RESET   
PLED LED  LED  S1/S3LED   S4 S5LED 
HDLED LED  LED  LED 
  LED LED  

115



 LED   7  SPK_PLED1 p.1No. 11 

SPEAKER DUMMY DUMMY +5V

PLEDPLED+ PLED+
1

 LED   

 ATA3   : (SATA_1: p.1No. 13 

 SATA3  6.0 Gb/s   SATA 

USB 2.0  9  USB_3_4 p.1No. 9 

DUMMY GND P+ P-
USB_PWR

GND P+ PUSB_PWR 1

 1    USB 2.0  2  

 4  CHA_FAN1 p.1No. 4 

4 3 21
FAN_SPEED_CONTROL CHA_FAN_SPEED FAN_VOLTAGE GND

  

4  CHA_FAN2

1

GND

p.1No. 12 

2

FAN_VOLTAGE

3

CHA_FAN_SPEED

4

FAN_SPEED_CONTROL

116



H510 Pro BTC+

4  CHA_FAN3 p.1No. 26  4  CHA_FAN4 p.1No. 25  4  CHA_FAN5 p.1No. 17  4  CHA_FAN6 p.1No. 24  4  CHA_FAN7 p.1No. 20  4  CHA_FAN8 p.1No. 23 

4 3 21
FAN_SPEED_CONTROL CHA_FAN_SPEED +12V GND

CPU  4  CPU_FAN1 p.1No. 1 

FAN_SPEED_CONTROL CPU_FAN_SPEED
+12V GND
1 2 34

 4  CPU  3  CPU   1-3 

ATX  24  ATXPWR1 p.1No. 8  24  ATXPWR2 p.1No. 7  24  ATXPWR3 p.1No. 21 
ATX 12V  8  ATX12V1 p.1No. 27 

12

24

1

13

 3  24  ATX  20  ATX   1  13  

5

1

 8 

ATX12V 

4  ATX 

 1  5

8

4



117



PCIe  4  PCIE_PWR3 p.1No. 16  4  PCIE_PWR4 p.1No. 18  4  PCIE_PWR5 p.1No. 19  4  PCIE_PWR6 p.1No. 22 

 
 :  4  PCIe   PSU    PSU    

 (M_Port1:p.1No. 15 

 

9 PERXN PERXP 8
GND 7 PETXP 6 PETXN 5

1 WAKE# 2 CLKN 3 CLKP 4 RST

SPI TPM  13  SPI_TPM_J1 p.1No. 14 

SPI_DQ3 +3.3V Dummy CLK SPI_MOSI RST# TPM_PIRQ
1
SPI_TPM_CS# GND RSMRST# SPI_MISO SPI_CS0 SPI_DQ2

 SPI   TPM   TPM    

118

H510 Pro BTC+

1.5 
 2  :  

 (PWRBTN1) p.1No. 5 

  / 

 (RSTBTN1) p.1No. 6 

 



119



1 
 H510 Pro BTC+  
 BIOS     VGA  CPU  http://www.asrock.com
1.1 
�  H510 Pro BTC+  �  H510 Pro BTC+  �  H510 Pro BTC+  � 1 x  ATA (SATA)  � 1 x  M.2 
120

H510 Pro BTC+



1.2 
 CPU  
 

� 
�  10  Intel� CoreTM  11  Intel� CoreTM  (LGA1200)
� Digi Power design � 4  �  Intel� Turbo Boost Max Technology 3.0
� Intel� H510
� 1 x DDR4 DIMM  *  2GB DRAM �  DDR4 3200/2933/2800/2666/2400/2133  ECC
 *  11  Intel� CoreTM (i9/i7/i5)  DDR4  3200CoreTM (i3)Pentium�  Celeron�  DDR4   2666 *  10  Intel� CoreTM (i9/i7)  DDR4  2933CoreTM (i5/i3)Pentium�  Celeron�  DDR4   2666 *  Memory Support List (http://www.asrock.com/) �  ECC UDIMM  ECC  � 32GB �  Intel� Extreme Memory Profile (XMP) 2.0
� 6 x PCI Express 3.0 x16 PCIE1  x16/PCIE2~6  x1) � 1 x Mining M_Port1  x1* *  USB 
�  GPU  Intel� UHD Graphics   VGA 
�  11  Intel� CoreTM  Intel� Xe  (Gen 12)  10  Intel� CoreTM  Gen 9 
�  HDMI 1.430Hz  4K x 2K (4096x2160) �  HDMI 1.4  HDMI  Auto
Lip SyncDeep Color (12bpc)xvYCC  HBR �  HDMI 1.4  HDCP 2.3
121



LAN  I/O 

� Gigabit LAN 10/100/1000 Mb/s � Giga PHY Intel� I219V �  Wake-On-LAN �  /ESD  �  802.3az �  PXE
� 1 x PS/2  /  � 1 x HDMI  � 2 x USB 2.0  ESD  � 2 x USB 3.2 Gen1  ESD  � 1 x RJ-45 LAN  LEDACT/LINK LED  SPEED
LED
� 1 x SATA3 6.0 Gb/s  NCQAHCI  � 1 x M.2 M Key  2260/2280/22110 M.2 SATA3 6.0 Gb/s




� 1 x  � 1 x SPI TPM  � 1 x  LED  � 1 x CPU 4  * CPU  1A (12W)  CPU  � 8 x  (4  ) * CHA_FAN3~CHA_FAN8  2.5A (30W) 

* CPU_FAN1CHA_FAN1  CHA_FAN2  4  � 3 x 24  ATX  � 1 x 8  PCIe 12V  � 4 x 4  PCIe  � 1 x USB 2.0  2  USB 2.0  ESD  � 1 x  � 1 x 

122



H510 Pro BTC+

BIOS  

� AMI UEFI Legal BIOS GUI � ACPI 6.0  �  SMBIOS 2.7 � CPU  / CPU GTVCCSADRAMVCCIO
VCCIN AUX 



� CPU �  CPU CPU

� CPU � CPU Vcore+12V+5V+3.3V



� Microsoft� Windows� 10 64-bit � LinuxUbuntu 16.04 LTS / Fedora 25 *  Linux O/S  Linux 




� FCCCE � ErP/EuP  ErP/EuP 

* http://www.asrock.com

 BIOS ""   

123



1.3 
 ""  ""

 CMOS  (CLRMOS1)  1  3 

2 

CLRMOS1  CMOS   15  CLRMOS1   5  BIOS  CMOS BIOS  CMOS CMOS   CMOS   CMOS 

124



H510 Pro BTC+
1.4 
 

 (9  PANEL1)  1   10 

GND PWRBTN#
PLEDPLED+

GND RESET# GND HDLEDHDLED+ 1

    

PWRBTN: 
RESET:  
PLED LED:  LED  S1/ S3  LED  S4  (S5)  LED 
HDLED LED:  LED  LED  
  LED LED  

125



 LED  (7  SPK_PLED1)  1  11 

SPEAKER DUMMY DUMMY +5V

PLEDPLED+ PLED+
1

 LED  

 ATA3   : (SATA_1:  1  13 

 SATA3   6.0 Gb/s   SATA 

USB 2.0  9  USB_3_4  1  9 

DUMMY GND P+ P-
USB_PWR

GND P+ PUSB_PWR 1

 USB 2.0 

 4  CHA_FAN1  1  4 

4 3 21
FAN_SPEED_CONTROL CHA_FAN_SPEED FAN_VOLTAGE GND

 

(4  CHA_FAN2) 1
 1  12  2 3
4

GND FAN_VOLTAGE CHA_FAN_SPEED FAN_SPEED_CONTROL

126



H510 Pro BTC+

(4  CHA_FAN3)  1  26  4  CHA_FAN4  1  25  (4  CHA_FAN5)  1  17  (4  CHA_FAN6)  1  24  (4  CHA_FAN7)  1  20  (4  CHA_FAN8)  1  23 

4 3 21
FAN_SPEED_CONTROL CHA_FAN_SPEED +12V GND

CPU  (4  CPU_FAN1)  1   1 

FAN_SPEED_CONTROL CPU_FAN_SPEED
+12V GND
1 2 34

 4  CPU    3  CPU   1-3

ATX  (24  ATXPWR1)  1  8  (24  ATXPWR2)  1  7  (24  ATXPWR3)  1  21 
ATX 12V  (8  ATX12V1)  1  27 

12

24

1

13

 3  24  ATX   20  ATX   1  13  

5

1

 8  ATX 12V 

 4  ATX 

 1  5 

8

4

127



PCIe  4  PCIE_PWR3  1  16  4  PCIE_PWR4  1  18  4  PCIE_PWR5  1  19  4  PCIE_PWR6  1  22 


 4  PCIe    PSU 

Mining  (M_Port1:  1  15 
9 PERXN PERXP 8
GND 7 PETXP 6 PETXN 5

1 WAKE# 2 CLKN 3 CLKP 4 RST

 Riser  

SPI TPM  13  SPI_TPM_J1  1  14 

SPI_DQ3 +3.3V Dummy CLK SPI_MOSI RST# TPM_PIRQ
1
SPI_TPM_CS# GND RSMRST# SPI_MISO SPI_CS0 SPI_DQ2

 SPI Trusted Platform Module TPM  TPM   

128

H510 Pro BTC+

1.5 


 (PWRBTN1)  1  5 

 / 

 (RSTBTN1)  1  6 

 



129




 SJ/T 11364-2006      10 




 


 

  (Pb)  (Cd)  (Hg)  (Cr(VI))  (PBB)  (PBDE)

X O O

O

O

O





X

O

O

O

O

O

O:  SJ/T 11363-2006  
X:  SJ/T 11363-2006   2002/95/EC   : 

130



H510 Pro BTC+
1 
 H510 Pro BTC+   
 BIOS     VGA  CPU   http://www.asrock.com
1.1 
�  H510 Pro BTC+  �  H510 Pro BTC+  �  H510 Pro BTC+  � 1 x Serial ATA (SATA)  � 1 x  M.2 
131



1.2 
 CPU  
 

� 
�  10  Intel� CoreTM  11  Intel� CoreTM   (LGA1200)
� Digi Power design � 4  �  Intel� Turbo Boost Max  3.0
� Intel� H510
� 1 x DDR4 DIMM  *  2GB DRAM �  DDR4 3200/2933/2800/2666/2400/2133  ECC 
 *  11  Intel� CoreTM (i9/i7/i5)  3200 DDR4CoreTM (i3) Pentium�  Celeron�  2666 DDR4  10  Intel� CoreTM (i9/i7/i5)  2933 DDR4CoreTM (i3) Pentium�  Celeron�  2666 DDR4 * (http:// www.asrock.com/) �  ECC UDIMM  (  ECC  ) � 32GB �  Intel� Extreme Memory Profile (XMP) 2.0
� 6 x PCI Express 3.0 x16  (PCIE1 x16 / PCIE2~6 x1) � 1 x  (M_Port1 x1)* *  USB 
�  GPU  Intel� UHD Graphics Built-in Visuals  VGA 
�  11  Intel� CoreTM  Intel� Xe  (  12  ) 10  Intel� CoreTM  9 
� Microsoft DirectX 12OpenGL 4.5 Intel� Built In VisualsIntel� Quick Sync Video OpenCL 2.1

132



H510 Pro BTC+

LAN  I/O  

�  HDMI 1.4  HDMI  Auto Lip SyncDeep Color (12bpc)xvYCC  HBR
�  HDMI 1.4  HDCP 2.3
� Gigabit LAN 10/100/1000 Mb/s � Giga PHY Intel� I219V �  �  �  802.3az EEE  �  PXE
� 1 x PS/2  � 1 x HDMI  � 2 x USB 2.0  � 2 x USB 3.2 Gen1  � 1 x RJ-45 LAN  LEDACT/LINK LED  SPEED
LED
� 1 x SATA3 6.0 Gb/s  NCQAHCI  � 1 x M.2  ,  M Key  2260/2280/22110 M.2 SATA3 6.0
Gb/s 
� 1 x  � 1 x SPI TPM  � 1 x  LED  � 1 x CPU  (4-pin) * CPU  1A (12W)  CPU  � 8 x  (4-pin) * CHA_FAN3~CHA_FAN8  2.5A (30W)  
* CPU_FAN1CHA_FAN1  CHA_FAN2  4-pin  � 3 x 24 pin ATX  � 1 x 8 pin PCIe 12V  � 4 x 4 pin PCIe  � 1 x USB 2.0  2  USB 2.0  � 1 x  � 1 x 

133



BIOS 

� AMI UEFI Legal BIOS  GUI  � ACPI 6.0  �  SMBIOS 2.7 � CPU  / CPU GTVCCSADRAMVCCIO
VCCIN AUX 



� CPU �  CPU CPU

� CPU � CPU Vcore+12V+5V+3.3V



� Microsoft� Windows� 10 64-bit � LinuxUbuntu 16.04 LTS / Fedora 25 *  Linux  Liunx 




� FCCCE � ErP/EuP Ready ErP/EuP ready 

* http://www.asrock.com

 BIOS    

134



H510 Pro BTC+
1.3 
 

 CMOS  (CLRMOS1)  1  3

2-pin 

 CLRMOS1  CMOS   15   CLRMOS1  pin  5  BIOS  CMOS  BIOS  CMOS CMOS  CMOS   CMOS 

135



1.4 
 


(9-pin PANEL1)  1   10

GND PWRBTN#
PLEDPLED+

GND RESET# GND HDLEDHDLED+ 1

    

PWRBTN (  ) 
RESET (  )  
PLED (  LED)  LED  S1/S3 LED  S4  (S5) LED  
HDLED (  LED)  LEDLED 
 LED LED 

136



H510 Pro BTC+

 LED  (7-pin SPK_PLED1)  1  11

SPEAKER DUMMY DUMMY +5V

PLEDPLED+ PLED+
1

 LED  

Serial ATA3   : (SATA_1:  1  13

 SATA3   SATA   6.0 Gb/s 

USB 2.0  9-pin USB_3_4)  1  9

DUMMY GND P+ P-
USB_PWR

GND P+ PUSB_PWR 1

 USB 2.0  


(4-pin CHA_FAN1)  1  4

4 3 21
FAN_SPEED_CONTROL CHA_FAN_SPEED FAN_VOLTAGE GND

 

1

(4-pin CHA_FAN2)

2

3
 1  4

12

GND FAN_VOLTAGE CHA_FAN_SPEED FAN_SPEED_CONTROL

137



(4-pin CHA_FAN3)  1  26 (4-pin CHA_FAN4)  1  25 (4-pin CHA_FAN5)  1  17 (4-pin CHA_FAN6)  1  24 (4-pin CHA_FAN7)  1  20 (4-pin CHA_FAN8)  1  23
CPU  (4-pin CPU_FAN1)  1   1

4 3 21
FAN_SPEED_CONTROL CHA_FAN_SPEED +12V GND

FAN_SPEED_CONTROL CPU_FAN_SPEED
+12V GND
1 2 34

 4-Pin CPU  (  )   3-Pin CPU  Pin 1-3

ATX  (24-pin ATXPWR1)  1  8 (24-pin ATXPWR2)  1  7 (24-pin ATXPWR3)  1  21

12

24

1

13

 24-pin ATX  20-pin ATX  Pin 1  Pin 13

138



H510 Pro BTC+

ATX 12V  (8-pin ATX12V1)  1  27

5

1

8

4

 8-pin ATX 12V  4-pin ATX  Pin 1  Pin 5

PCIe  (4-pin PCIE_PWR3)  1  16 (4-pin PCIE_PWR4)  1  18 (4-pin PCIE_PWR5)  1  19 (4-pin PCIE_PWR6)  1  22
 (M_Port1:(  1  15

9 PERXN PERXP 8
GND 7 PETXP 6 PETXN 5

1 WAKE# 2 CLKN 3 CLKP 4 RST

  4-pin PCIe   PSU 
 

SPI TPM  (13-pin SPI_TPM_J1)  1  14

SPI_DQ3 +3.3V Dummy CLK SPI_MOSI RST# TPM_PIRQ
1
SPI_TPM_CS# GND RSMRST# SPI_MISO SPI_CS0 SPI_DQ2

 SPI  (TPM)   TPM   

139

1.5 



(PWRBTN1)  1  5

 


(RSTBTN1)  1  6

 



140

Bahasa Indonesia

H510 Pro BTC+

Spesifikasi
Platform CPU

� Desain Kapasitor Solid
� Mendukung Prosesor Intel� CoreTM Gen 10 dan Prosesor Intel� CoreTM Gen 11 (LGA1200)
� Desain Digi Power � Desain 4 Fase Daya � Mendukung Teknologi Intel� Turbo Boost Max 3.0

Chipset

� Intel� H510

Memori

� 1 x Slot DIMM DDR4 * DRAM 2 GB per modul tidak didukung. � Mendukung DDR4 3200/2933/2800/2666/2400/2133 non-ECC,
memori tanpa buffer * Prosesor Intel� CoreTM Gen 11 (i9/i7/i5) mendukung DDR4 hingga 3200; CoreTM (i3), Pentium� dan Celeron� mendukung DDR4 hingga
2666. * Prosesor Intel� CoreTM Gen 10 (i9/i7) mendukung DDR4 hingga 2933; CoreTM (i5/i3), Pentium� dan Celeron� mendukung DDR4 hingga
2666.
* Lihat Daftar Dukungan Memori pada situs web ASRock untuk
informasi selengkapnya. (http://www.asrock.com/) � Mendukung modul memori ECC UDIMM (berjalan dalam mode
non-ECC) � Kapasitas maksimum memori sistem: 32GB � Mendukung Intel� Extreme Memory Profile (XMP) 2.0

Slot Ekspansi

� 6 x Slot PCI Express 3.0 x16 (PCIE1 pada x16 / PCIE2~6 pada x1) � 1 x Port Mining (M_Port1 pada x1)*
* Mendukung kit USB Type Riser

Grafis

� Intel� UHD Graphics Built-in Visuals dan output VGA hanya didukung dengan prosesor yang terintegrasi GPU.
� Prosesor Intel� CoreTM Gen 11 mendukung Arsitektur Grafis Intel� Xe (Gen 12). Prosesor Intel� CoreTM Gen 10 mendukung Grafis Gen 9

141

Bahasa Indonesia

� Mendukung HDMI 1,4 dengan resolusi maksimum hingga 4K x 2K (4096x2160) @ 30Hz
� Mendukung Auto Lip Sync, Kedalaman Warna (12bpc), xvYCC, dan HBR (Audio High Bit Rate) dengan Port HDMI 1.4 (memerlukan monitor yang kompatibel dengan HDMI)
� Mendukung fungsi HDCP 2.3 dengan Port HDMI 1.4

LAN

� Gigabit LAN 10/100/1000 Mb/s � Giga PHY Intel� I219V � Mendukung Wake-On-LAN � Mendukung Perlindungan dari Petir/ESD � Mendukung Ethernet 802.3az Hemat Energi � Mendukung PXE

I/O Panel Belakang

� 1 x Port Mouse/Keyboard PS/2 � 1 x Port HDMI � 2 x Port USB 2.0 (Mendukung Perlindungan dari ESD) � 2 x Port USB 3.2 Gen1 (Mendukung Perlindungan dari ESD) � 1 x Port LAN RJ-45 dengan LED (LED ACT/LINK dan LED
SPEED)

Penyimpanan

� 1 x Konektor SATA3 6.0 Gb/s, mendukung NCQ, AHCI, dan Hot Plug
� 1 x Soket M.2, mendukung modul tipe Kunci M 2260/2280/22110 M.2 SATA3 6,0 Gb/s

Konektor

� 1 x Header Panel Sistem � 1 x Header SPI TPM � 1 x Header LED Daya dan Speaker � 1 x Konektor Kipas CPU (4-pin)
* Konektor Kipas CPU mendukung kipas CPU dengan daya kipas
maksimum 1A (12W). � 8 x Konektor Kipas Chassis (4-pin)
* CHA_FAN3~CHA_FAN8 mendukung kipas sasis dengan daya kipas
maksimum 2,5A (30W).
* CPU_FAN1, CHA_FAN1, dan CHA_FAN2 dapat menyesuaikan
kecepatan kipas 4-pin. � 3 x Konektor Daya ATX 24 pin � 1 x Konektor Daya PCIe 8 pin 12V

142

Bahasa Indonesia

H510 Pro BTC+

Fitur BIOS

� 4 x Konektor Daya PCIe 4 pin � 1 x Header USB 2.0 (Mendukung 2 port USB 2.0) (Mendukung
Perlindungan dari ESD) � 1 x Tombol Daya � 1 x Tombol Atur Ulang
� AMI UEFI Legal BIOS dengan dukungan GUI multibahasa � ACPI 6.0 Kompatibel dengan aktivitas pengaktifan � Dukungan SMBIOS 2.7 � Multipengatur Tegangan CPU Core/Cache, CPU GT, VCCSA,
DRAM, VCCIO, VCCIN AUX

Monitor Perangkat Keras

� Takometer Kipas: CPU, Kipas Chassis � Kipas Hening (Penyesuaian otomatis kecepatan kipas sasis
berdasarkan suhu CPU): CPU, Kipas Chassis � Kontrol Multikecepatan Kipas: CPU, Kipas Chassis � Pemantauan tegangan: CPU Vcore, +12V, +5V, +3,3V

OS

� Microsoft� Windows� 10 64-bit

� Linux: Ubuntu 16.04 LTS / Fedora 25

* Hanya mendukung fungsi dasar O/S Linux, dikarenakan kompabilitas

sistem Linux sendiri, tidak ada jaminan bahwa semua fungsi didukung.

Sertifikasi

� FCC, CE � Mendukung ErP/EuP (Memerlukan catu daya untuk ErP/EuP)

* Untuk informasi rinci tentang produk, kunjungi situs web kami: http://www.asrock.com
Perlu diketahui, overclocking memiliki risiko tertentu, termasuk menyesuaikan pengaturan pada BIOS, menerapkan Teknologi Untied Overclocking, atau menggunakan alat bantu overclocking pihak ketiga. Overclocking dapat mempengaruhi stabilitas sistem, atau bahkan mengakibatkan kerusakan komponen dan perangkat sistem. Risiko dan biaya apa pun menjadi tanggungan Anda. Kami tidak bertanggung jawab atas kemungkinan kerusakan karena overclocking.

143

Contact Information
If you need to contact ASRock or want to know more about ASRock, you're welcome to visit ASRock's website at http://www.asrock.com; or you may contact your dealer for further information. For technical questions, please submit a support request form at https://event.asrock.com/tsd.asp ASRock Incorporation 2F., No.37, Sec. 2, Jhongyang S. Rd., Beitou District, Taipei City 112, Taiwan (R.O.C.) ASRock EUROPE B.V. Bijsterhuizen 11-11 6546 AR Nijmegen The Netherlands Phone: +31-24-345-44-33 Fax: +31-24-345-44-38 ASRock America, Inc. 13848 Magnolia Ave, Chino, CA91710 U.S.A. Phone: +1-909-590-8308 Fax: +1-909-590-1026

DECLARATION OF CONFORMITY
Per FCC Part 2 Section 2.1077(a)
Responsible Party Name: ASRock Incorporation Address: 13848 Magnolia Ave, Chino, CA91710
Phone/Fax No: +1-909-590-8308/+1-909-590-1026 hereby declares that the product
Product Name : Motherboard Model Number : H510 Pro BTC+ Conforms to the following specifications:
FCC Part15, SubpartB,Unintentional Radiators Supplementary Information:
is device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) is device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Representative Person's Name: James
Signature : Date : May 12, 2017

EU Declaration of Conformity

For the following equipment: Motherboard (Product Name)
H510 Pro BTC+ / ASRock (Model Designation / Trade Name)
ASRock Incorporation (Manufacturer Name)
2F., No.37, Sec. 2, Jhongyang S. Rd., Beitou District, Taipei City 112, Taiwan (R.O.C.) (Manufacturer Address)

 EMC --Directive 2014/30/EU (from April 20th, 2016)

 EN 55022:2010/AC:2011 Class B

 EN 55024:2010/A1:2015

 EN 55032:2012+AC:2013 Class B

 EN 61000-3-3:2013

 EN 61000-3-2:2014

 LVD --Directive 2014/35/EU (from April 20th, 2016)

 EN 60950-1 : 2011+ A2: 2013

 EN 60950-1 : 2006/A12: 2011

 RoHS -- Directive 2011/65/EU  CE marking

(EU conformity marking)

ASRock EUROPE B.V. (Company Name) Bijsterhuizen 1111 6546 AR Nijmegen The Netherlands (Company Address) Person responsible for making this declaration:
(Name, Surname) A.V.P (Position / Title) June 5, 2021 (Date) P/N: 15G062308000AK V1.0