for NOYAFA models including: NF-8209, NOYAFA,SHENZHEN NOYAFA ELECTRONIC CO.,LTD,NOYAFA,Advanced,Network,Cable,Tester,With,PoE&,NCV,&,Lamp,For,CAT5e/CAT6/CAT6a,,Multifunction,Wire,Tracker,Cable,Tester,For,Tracker,Underground,Telephone,Line,Finder,Home,Repair,,
User manual 1pc 1pc. 1Your excellent helper in cable test! Your excellent helper in cable test! 2 Diagram of Series Products NF-911 NF-5120 NF-2030 NF-8601S NF-488 NF-711F NF-272L NF-858C NF-198 NF-511 NF-707 NF-309 9.FAQ Result Reason or solution Different testing results for
MODEL:NF-8209. VER: V2. INSTRUCTION MANUAL. Network Cable Tester. ORIGINAL. AUTHENTIC. Page 2. Your excellent helper in cable test! Table of ...
User manual 1pc 1pc. 1Your excellent helper in cable test! Your excellent helper in cable test! 2 Diagram of Series Products NF-911 NF-5120 NF-2030 NF-8601S NF-488
MODEL:NF-8209 Network Cable Tester INSTRUCTION MANUAL ORIGINAL AUTHENTIC VER: V2 Read the precautions before your operation Please do not place the device in a location that is dusty, humid, or hot (above 40°C). Please use a battery that meets the specifications, otherwise the device may be damaged. Please do not disassemble the device. Repair and maintenance should be done by a professional staff. When not using the device for a long time, please remove the battery inside the test terminal to prevent the battery liquid from leaking out. Please do not use this device to detect live power lines (such as 220V power supply lines), the device may be damaged and personal safety may be influenced. Please do not perform related operations on the communication line during thunderstorms to prevent lightning strikes and personal safety. Table of Contents Overview...................................................................0 1 Keypard display and features..............................01 Product Operation................................................03 1.Continuity testing.............................................03 2.Length measurement........................................05 3.Cable scan...........................................................05 4.PoE testing.....................................................06 5.Port Flash & Switch details testing.......................07 6.Setting.............................................................08 7.Spefication........................................................09 8.Accessories.........................................................10 9.FAQ..................................................................... 11 Diagram of Series Products.....................................12 Your excellent helper in cable test! Your excellent helper in cable test! Overview NF-8209 is a new generation to offer digital and analog signaling all in one network toner and probe. It has three modes for options to track cable like digital mode, analog mode and PoE mode. That means it's equipped with the most powerful cable location technologies for any work environment. Also, it includes cable length measurement , cable faults testing, PoE testing, hub blink and NCV function, all these makes it a must-tool for cabling engineers. Keyparddisplayandfeatures POE Length/flash CONT SCAN Earphone RJ45-CONTtesting EMITTER RECEIVER REMOTE 1 Your excellent helper in cable test! Lamp Lampcontrol Left/Up Back Power Right/Down Confirm Lamp Power Analog Digtal EMITTER NCV SEN Lamp Power/Set RECEIVER Your excellent helper in cable test! 2 Product Operation Turn on the device and enter the below main Menu CONT Lenght SCAN POE Fiash Setting 1. CONT-- Test open, short, cross,ect for STP, UTP cable. 2. Length--measure length of lan cable, range is 2.5m~200m. 3. Scan--Analog/Digital/ PoE mode to locate lan cables. 4. PoE-- available for standard or non-standard PoE switch (5~60V), identify AT or AF standard of PSE type. 5. Flash--locate network port by the flashing port light on switch/ router. 6. Setting--Set Language, backlight time, auto-off time, contrast and version. 1. Continuity testing Connect one end of cable to "CONT" port of tranmistter on the left side, the other end to the RJ45 port of remote, Press "OK" to start testing. If the cable is a good one, the result will be as below. C R : 1 2 3 4 5 6 7 8 M: 1 2 3 4 5 6 7 8 UTP lan cable C R : 1 2 3 4 5 6 7 8 G M: 1 2 3 4 5 6 7 8 G STP lan cable 3 Your excellent helper in cable test! 1.1 Possible results Only if a cable exsits short circuit, no matter it exsits cross, breakage or not,the testing result will only display "Short" information. If it doesn't exsit short circuit, then it would display what actually it is. C short R : M: 1 2 3 4 5 6 7 8 C R : 1 2 3 4 X 6 7 X M: 1 2 3 4 X 6 7 X Pin12,Pin45arebothshorted Pin5&Pin8arebroken C R : 1 2 3 4 5 6 7 8 M: 1 2 3 4 5 6 7 8 Pin56,Pin18arecross C R : 1 2 3 4 5 6 7 8 M: 1 2 3 4 5 6 7 8 Goodcondition 1.2 Cable Open If the LCD screen display "Cable Open!", there are several reasons for this. 1. all the pins are open indeed. 2. no cable is connected. 3. the remote is not connected. 4. Connect with wrong port. C Cable open! Your excellent helper in cable test! 4 2. Length measurement Connect one end of cable to "Length/Port flash" port, disconnect the cable at far end, choose "Length" on the main menu, and select the preferred unit (meter/ yard/ feet ) before testing. then press start to measure and the result will come out soon on the screen. 1280.8meter 3612.1meter 4580.8meter 7880.8meter From the image, it means there exsits problem at 12.1m. To make sure it is short or broke there, you can test its continuity to know details. Kind reminds when measuring cable length. 1. the lan cable to be tested must be de-energized. 2. disconnect the cable at the far end, no remote, no other devices connected! 3. The range must be 2.5m~200m, otherwise, it would be display 0 meter. 3. Cable scan Connect the cable to be tested to "SCAN" port of tranmistter on the left side, enter "SCAN" on the main menu, press ok to choose scan mode you prefer, the default is digital mode, the other modes is Analog & PoE. then set the corresponding 5 Your excellent helper in cable test! mode on receiver accordingly. After that, hold the receiver to locate cable at the other end, the loudest voice is the correct one. SCAN SCAN SCAN Digital mode Analog mode PoE mode 3.1. Attention: If the tranmistter is in PoE scan and digital scan mode, the receiver must be in digital mode. the analog scan in transmitter matches analog mode in receiver. If the modes are not matched correctly, even the receiver touch the correct cable, it won't generate tone, either. 3.2. Non-contact voltage detecting: press the "Power/Set" button on the receiver, if the "NCV" indicator is lit on, then you can use the receiver to detect AC voltage presence. 4. PoE Testing 4.1 Standard PoE device It can test the information of standard PoE device, such as POE voltage, power supply polarity, power supply mode and also the type of PSE(af or at standard). Connect the cable into "PoE" port, the testing result display as below image. Pins providing power type - -Polarity 12345678 PoE Endspan IEEE 802.3at -53.6VDC Mode Voltage Your excellent helper in cable test! 6 4.2 Non-standard PoE device If the PoE device is non-standard, it can also test POE voltage, power supply polarity, power supply mode, but it can't tell the type of PSE, just display "Non standard". Connect the cable into "PoE" port, the testing result display as below image. Pins providing power Type Polarity 12345678 PoE 8pins Non Standard 53.6VDC Mode Voltage Attention: If all the 8 pins are providing power, it won't display polarity. 4.3 If connected with PoE device, the result can be displayed after a few secs, it there is no result displayed after 30secs, then the device connected may not be PoE device. 5. Port Flash & Switch details testing Connect a lan cable to "Length/Flash" port on the main unit, choose "Flash" on the main menu to start testing. The 2 indicators on the "Length / Flash" port will be lit and flash. Then observe the ports on switch, if there is a port whose flash frequency is 3 secs, and slower than all the other ports, it tells you the port is the target one you're looking for. Also, the device can tell you the connected switch's information, such as its speed (10M/100M/1000M), transmitting modes (FDX: full duplex / HDX: half duplex) Protocol (Auto-Nego / Non-AutoNego). See the graph for ref. as below. Flash 1000M FDX P: Auto-Nego Testing...... 7 Your excellent helper in cable test! 6. Setting 6.1. Backlight setting Adjust the backlight time among 15s, 30s, 60s, on, and off. Setting LangEnglish -> BackLight30s AutoOFF15min 6.2. Auto-off time adjust the backlight time among 15mins, 30mins, 1h, OFF. Setting LangEnglish BackLight30s -> AutoOFF15min 6.3. Contrast setting Press the left and right keys to adjust the contrast to suit yourself. Setting Contrast 28 Your excellent helper in cable test! 8 6.5. Version information To check version information of software and hardware . Setting Hardware:V1.0 Software:V1.0 7. Specification EMITTER Cable type CAT5e,CAT6, CAT6a (STP & UTP) Wiremap Test with switch directly Yes Max range Cable type 600m CAT5e,CAT6, CAT6a (STP & UTP) Length Test range Accuracy 2.5~200m ±1.6m Breakage location Cable type Yes CAT5e,CAT6, CAT6a (STP & UTP) Scan Max. signal voltage 9±1Vp-p Frequency 130KHz Analog / Digital mode Yes Max range 600m Test range DC 5~60V standard / non-standard PoE switch POE Voltage display PSE type Yes Standard : IEEE 802.3af/at ; Non standard LCD display Power supply Low battary warning EMITTER Auto-off time Voltage protection Max working current Size Sentivity adjustable AC Voltage detecting Lamp RECEIVER Battary type Low battary warning Max working current Size REMOTE Wiremap Port Voltage protection Size 128*64 Dot-matrix with backlight AAA battary *3 2.7V 15min/ 30min/ 60min/ OFF DC48V 5mA <150mA 130*70*28mm Yes Yes Yes 9V*1pc 6± 0.5V <100mA 210*43*27mm RJ45 DC48V 5mA 65*37*23mm 8. Accessories Emitter Receiver Remote User manual 1pc Earphone 1pc Cable adaptors 1pc Carry bag 1pc Quality certificate 1pc 1 set 1pc 1pc 09 Your excellent helper in cable test! Your excellent helper in cable test! 10 9.FAQ Result Different testing results for one same cable Length measured 0.0m No results display when test PoE No flashing port when use port flash Reason or solution Check whether the cable ends are connected well Keeps the ports clean Connects to wrong port, "Length/Flash" is the correct one. Make sure the tested cable length is 2.5m~200m Connects to wrong port, "PoE" is the correct one Test the cable's continuity to make sure it is a good cable Check the PoE device is poweron Connects to wrong port, "Length/Flash" is the correct one Test the cable's continuity to make sure it is a good cable Check the router or switch is on Connects to wrong port, "SCAN" is the correct one No tone when track cable The mode of transmitter and receiver must keep the same Check whether the battary is low Turn up the sensitivity The text on screen is blurry Adjust the contrast to suit yourself Turn on the device and autoReplace a new battary off soon 11 Your excellent helper in cable test! Diagram of Series Products NF-8601S NF-309 NF-198 NF-511 NF-2030 NF-488 NF-858C NF-911 NF-707 NF-711F NF-5120 NF-272L Your excellent helper in cable test! 12Corel PDF Engine Version 21.0.0.593 CorelDRAW 2019