Home › CISCO › CISCO Cisco Catalyst Series Wireless Access Points User Guide

CISCO Cisco Catalyst Series Wireless Access Points User Guide

File info: application/pdf · 40 pages · 2.37MB

Cisco Catalyst Series 9105AXW Access Point Getting Started Guide

Cisco Catalyst Series 9105AXW Access Point Getting Started ...

C9105AXWT-B - Cisco Catalyst 9105axw Dual Band 802.11ax 1.49 Gbit/s Wireless Access Point - 2.40 Ghz, 5 Ghz - Internal - Mimo Technology - 4 X Network (rj-45) - 2.5 Gigabit Ethernet, Gigabit Ethernet - Bluetooth 5 - Wal…

Full PDF Document

If the inline viewer fails, it will open the original document in compatibility mode automatically. You can also open the file directly.

Extracted Text

GETTIN G STA RTED GU ID E
Cisco Catalyst Series 9105AXW and 9105AXWT Wireless Access Points
First Published: August 11, 2020 Last Updated: April 1, 2021
Cisco Systems, Inc. www.cisco.com 1

Cisco Catalyst Series 9105AXW and 9105AXWT Wireless Access Points
1 About this Guide 2 About the Cisco Catalyst Series 9105AXW and 9105AXWT Wireless Access Points 3 Safety Instructions 4 Unpacking 5 AP View s, Ports, and Connectors 6 Preparing the AP for Installation 7 Installation Overview 8 Perform ing a Pre-Installation Configuration 9 M ounting the Access Point 1 0 Pow ering the Access Point 1 1 Configuring and Deploying the Access Point 1 2 Checking the Access Point LEDs 1 3 M iscellaneous Usage and Configuration Guidelines 1 4 FAQs 1 5 Related Docum entation 1 6 Declarations of Conform ity and Regulatory Inform ation
Com m unications, Services, and Additional Inform ation Cisco Bug Search Tool
2

Cisco Catalyst Series 9105AXW and 9105AXWT Wireless Access Points

1 About this Guide
This guide provides instructions on how to install your Cisco Catalyst Series 9105AXW and 9105AXWT access points and provides links to resources that can help you configure it. This guide also provides mounting instructions and troubleshooting information.
Note that the C9105AXW and C9105AXWT access points are referred to as the access point or the AP in this document.

Note The documentation set for this product strives to use bias-free language. For purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product.
2 About the Cisco Catalyst Series 9105AXW and 9105AXW T W ireless
Access Points
The Cisco Catalyst 9105AXW and 9105AXWT series wireless access points are advanced dual-band, dual-concurrent, enterprise 802.11ax (Wi-Fi 6) APs with integrated antennas. These wall-mounted APs support 2x2:2 SS MU-MIMO applications and are designed to use both 2.4 GHz and the 5 GHz bands. The APs support full interoperability with leading 802.11ax and 802.11ac clients, along with a mixed deployment with other APs and controllers.
A full listing of the AP's features and specifications are provided in the Cisco Catalyst 9105AXW and 9105AXWT Series Access Point Data Sheet, at the following URL: https://www.cisco.com/c/en/us/products/collateral/wireless/catalyst-9100ax-access-points/datasheet-c78-744062. html
Cisco Catalyst Series 9105AXW and 9105AXW T W ireless Access Point Features
The C9105AXW and C9105AXWT wireless APs are wireless controller-based products and support the following features:
Two dual-band internal antennas and one single-band internal IoT (BLE or ZigBee) antenna in both the C9105AXW and C9105AXWT-x AP models

Note The `x ' in the model numbers represents the regulatory domain. For information on supported regulatory domains, see the " AP M odel N umbers and Regulatory Domains" section on page 5.
Integrated antennas that are directional in azimuth, for both 2.4 GHz (peak gain 3dBi) and 5 GHz (peak gain 5dBi) bands.
The following hardware external interfaces:
-- 1x100/1000/2500 Multigigabit Ethernet (RJ-45)
-- 3x10/100/1000 BASE-T Ethernet (RJ-45)

N ote

One of these Ethernet ports serves as a PoE-Out port. However, this PoE-Out port does not provide any power output when the AP is powered by 802.3af power.

Cisco Catalyst Series 9105AXW and 9105AXWT Wireless Access Points

-- RS-232 console interface through RJ-45 -- Pass-through port (RJ-45)

N ote

The C9105AXWT does not have pass-through functionality as it is connected to the WAN port on the back of the AP using the jumper cable available in the teleworker kit. For more information, see the Mounting the Kit C9105AXWT_COVER= to the AP section.

-- Passive pass-through port (RJ-45)
-- Mode button (enables partial or full system configuration recovery)
-- USB 2.0 Port
One multi-color LED Status indicator. see the "Checking the Access Point LEDs" section on page 25 for information on the colors of the LED status indicator.
Simultaneous 2x2 Multiple-Input Multiple-Output (MIMO) with 2 spatial streams for both 2.4 GHz and 5 GHz bands.
Multiuser (MU) MIMO technology with 2 spatial streams for downlink.
MIMO equalization capabilities, which optimize uplink performance and reliability by reducing the impact of signal fade.
Orthogonal Frequency Division Multiple Access (OFDMA)-based scheduling for both uplink and downlink.
Spatial Reuse (also known as Basic Service Set (BSS) coloring) which allows APs and their clients to differentiate between BSSs, thus permitting more simultaneous transmissions.
New power savings mode called Target Wake Time (TWT) which allows the client to stay asleep and wake up only at pre-scheduled (target) times to exchange data with the AP. This provides significant energy savings for battery-operated devices.
Cisco Digital Network Architecture (DNA) support enables Cisco DNA Spaces, Apple FastLane and Cisco Identity Services Engine.
Cross-AP Noise Reduction, a Cisco innovation that enables APs to intelligently collaborate in real time about RF conditions so that users connect with optimized signal quality and performance.
Optimized AP Roaming for ensuring that client devices associate with the AP in their coverage range that offers the fastest data rate available.
Cisco CleanAir delivers proactive, high-speed spectrum intelligence across 20-, 40-, and 80-MHz-wide channels to combat performance problems arising from wireless interference.
This AP supports both lightweight deployments (using Cisco Wireless Controllers) and Cisco Embedded Wireless Controller deployments. The AP can operate in the following modes:
Local--This is the default mode for the Cisco AP. In this mode, the AP serves clients. In local mode, the AP creates two CAPWAP tunnels to the Cisco WLC, one for management and the other for data traffic. This is known as central switching because the data traffic is switched (bridged) from the AP to the controller where it is then routed.
FlexConnect--In FlexConnect mode (previously known as HREAP), the data traffic is switched locally and is not sent to the controller. In this mode, the Cisco AP behaves like an autonomous AP, but is managed by the Cisco WLC. Here, the AP continues to function even if connection to the controller is lost.

Cisco Catalyst Series 9105AXW and 9105AXWT Wireless Access Points

Monitor--In the monitor mode, specified Cisco APs can exclude themselves from handling data traffic between clients and the infrastructure. These APs act as dedicated sensors for location based services (LBS), rogue AP detection, and intrusion detection (IDS). When APs are in monitor mode, they actively monitor the airwaves and typically do not serve clients.
Sniffer--In the wireless sniffer mode, the AP starts sniffing the air on a given channel. It captures and forwards all the packets from the clients on that channel to a remote machine that runs Airopeek or Wireshark (packet analyzers for IEEE 802.11 wireless LANs). This includes information on the time stamp, signal strength, packet size, etc.

Note In the sniffer mode, the server to which the data is sent should be on the same VLAN as the wireless controller management VLAN otherwise an error will be displayed.
OEAP--This is the office extend mode for the Cisco AP.

AP M odel Numbers and Regulatory Domains

AP Type
Access point (wall-plate) for indoor environments, with internal antennas

M odel Number C9105AXW-x C9105AXW-EWC-x
C9105AXWT-x

Details
Dual-band, controller-based 802.11ax
C9105AXW-x with a Cisco Embedded Wireless Controller software image
Dual-band, teleworker, controller-based 802.11ax

You need to verify whether the AP model you have is approved for use in your country. The x in the model number is a placeholder for the regulatory domain. To verify approval and to identify the regulatory domain that corresponds to a particular country, visit http://www.cisco.com/go/aironet/compliance. Not all regulatory domains have been approved. As and when they are approved, this compliance list will be updated.

Antennas and Radios
The C9105AXW and C9105AXWT AP models have two internal dual-band antennas with a dedicated 2.4 GHz radio and a 5 GHz radio, and one internal single-band antenna with a dedicated 2.4 GHz IOT radio that supports BLE and Zigbee.
The AP can be vertically mounted on a wall or on a standard junction box. Physical security is offered with the included Torx screw and the option to add a Kensington lock.

Cisco Catalyst Series 9105AXW and 9105AXWT Wireless Access Points
Access Point Antenna Radiation Patterns
Figure 1 C9105AXW and C9105AXWT -- Dual-band Antenna (2.4 GHz) -- Azimuth
6

Cisco Catalyst Series 9105AXW and 9105AXWT Wireless Access Points Figure 2 C9105AXW and C9105AXWT -- Dual-band Antenna (2.4 GHz) -- Elevation
7

Cisco Catalyst Series 9105AXW and 9105AXWT Wireless Access Points Figure 3 C9105AXW and C9105AXWT -- Dual-band Antenna (5 GHz) -- Azimuth
8

Cisco Catalyst Series 9105AXW and 9105AXWT Wireless Access Points Figure 4 C9105AXW and C9105AXWT -- Dual-band Antenna (5 GHz) -- Elevation
9

Cisco Catalyst Series 9105AXW and 9105AXWT Wireless Access Points Figure 5 C9105AXW and C9105AXWT -- BLE Antenna -- Azimuth
10

Cisco Catalyst Series 9105AXW and 9105AXWT Wireless Access Points Figure 6 C9105AXW and C9105AXWT -- BLE Antenna -- Elevation
11

Cisco Catalyst Series 9105AXW and 9105AXWT Wireless Access Points

3 Safety Instructions
Translated versions of the following safety warnings are provided in the translated safety warnings document that is shipped with your access point.

W arning

IM PORTAN T SAFETY IN STRUCTION S
This w arning symbol means danger. You are in a situation that could cause bodily injury. Before you w ork on any equipment, be aw are of the hazards involved w ith electrical circuitry and be familiar w ith standard practices for preventing accidents. Use the statement number provided at the end of each w arning to locate its translation in the translated safety w arnings that accompanied this device.
SAVE THESE IN STRUCTION S Statement 1071

W arning

Read the installation instructions before using, installing or connecting the system to the pow er source. Statement 1004

W arning

This product relies on the building's installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than 20A. Statement 1005

W arning Installation of the equipment must comply w ith local and national electrical codes. Statement 1074

W arning

In order to comply w ith FCC radio frequency (RF) exposure limits, antennas should be located at a minimum of 12 inches (30 cm) or more from the body of all persons. Statement 332

W arning

Ultimate disposal of this product should be handled according to all national law s and regulations. Statement 1040

W arning

Ultimate disposal of this product should be handled according to all national law s and regulations. Statement 1047

W arning

This equipment is suitable for use in environment air spaces (plenums) in accordance w ith Section 300.22 (C) of the N ational Electrical Code, and Sections 2-128, 12-010(3) and 12-100 of the Canadian Electrical Code, Part 1, CSA C22.2. External pow er supply, pow er adapter and/or pow er injector, if provided, are not suitable for installation in air spaces. Statement 440

Cisco Catalyst Series 9105AXW and 9105AXWT Wireless Access Points
4 Unpacking
To unpack the access point, follow these steps: Step 1 Unpack and remove the access point and the accessory kit from the shipping box. Step 2 Return any packing material to the shipping container and save it for future use. Step 3 Verify that you have received the items listed below. If any item is missing or damaged, contact your Cisco
representative or reseller for instructions. � The access point � Torx security screw and mylar label to cover the screw. The following accessories can be ordered separately from Cisco: Mid-span power injector (AIR-PWRINJ6=) when PoE is not available For the C9105AXWT-x, the teleworker cradle kit (C9105AXWT-COVER=) which includes one back cover (with four rubber feet), one Ethernet cable, and one RJ-45 jumper cable
13

Cisco Catalyst Series 9105AXW and 9105AXWT Wireless Access Points
5 AP View s, Ports, and Connectors
Figure 7 Face of the 9105AXW and C9105AXWT M odels
1 Security screw hole location under a mylar cover The security screw locks the AP to its mounting bracket (AIR-AP-BRACKET-4).
2 USB 2.0 port 3 Location of the Kensington lock slot 4 Status LED1 5 Location of the ports and connectors, on the base of the AP 1. For more information on the status LED, see "Checking the Access Point LEDs" section on page 25.
14

Cisco Catalyst Series 9105AXW and 9105AXWT Wireless Access Points Figure 8 Ports and Connectors on the 9105AXW and C9105AXWT M odels

1 Mode button1 2 Location of the Kensington lock slot

6 RJ-45 console port 7 Pass-through port2

3 1GbE port (LAN port 3)

8 USB 2.0 port

4 PoE-In1GbE port (LAN port 2)

9 Passive pass-through (RJ-45) port from the back of the AP to the base of the AP.3

PSE (LAN port 1) 5 This port provides 802.3af Power Sourcing Equipment
(PSE) PoE-O ut power on the LAN 1 Ethernet interface, when powered by 802.3at power.

2.5GbE mGig uplink port4 which supports the 10 following:
� Inline power capability
� 10/100/1000/2500 mGig capability

� Auto-M DIX (automatically supports either straight-through or crossover cables)

� 802.3af/at power over Ethernet interface.

1. For more information on how to use the Mode button, see "Using the Mode Button" section on page 26.
2. The pass-through port on the C9105AXWT functions like an mGig uplink port. This behavior is observed since the passive pass-through port is connected to the uplink port on the back of the AP through the RJ-45 jumper cable available in the teleworker kit. For more information on this behavior change in the C9105AXWT, see the Mounting the Kit C9105AXWT_COVER= to the AP section.
3. See 2.
4. See 2.

Note When the AP is in RLAN mode, it supports up to four wired clients on the LAN ports.

Cisco Catalyst Series 9105AXW and 9105AXWT Wireless Access Points 16

Cisco Catalyst Series 9105AXW and 9105AXWT Wireless Access Points

6 Preparing the AP for Installation
Before you mount and deploy your access point, we recommend that you perform a site survey (or use the site planning tool) to determine the best location to install your access point.
You should have the following information about your wireless network available:
Access point locations.
Access point mounting options: below a suspended ceiling, on a flat horizontal surface, or on a desk top.

Note You can mount the access point above a suspended ceiling but you must purchase additional mounting hardware: See " M ounting the Access Point" section on page 20 for additional information.
Access point power options: 802.3at (PoE+) (Cisco Power Injector AIR-PWRINJ6=), 802.3af (Cisco Power Injector AIR-PWRINJ5=), Cisco Universal PoE (Cisco UPOE), or hub (usually located in a wiring closet).

Note � Access points mounted in a building environmental airspace must be powered using PoE to comply with safety regulations.
� If 802.3af is used, the USB port and LAN PSE1 port will be off.
Operating temperature: 32�--122�F (0�--50�C)

Note When installing the AP in an environment where the ambient temperature is in the range of 104�--122�F (>40�--50�C), the access point configuration will change from 8x8 to 4x4 on the 5 GH z radios and the uplink Ethernet will downgrade to 1GbE. H owever, the USB port will remain enabled.
Cisco recommends that you make a site map showing access point locations so that you can record the device MAC addresses from each location and return them to the person who is planning or managing your wireless network.

7 Installation Overview
Installing the access point involves these operations:

Step 1 Step 2 Step 3 Step 4

Performing a Pre-Installation Configuration, page 18 (optional) M ounting the Access Point, page 20 Powering the Access Point, page 23 Preparing the AP for Installation, page 17

Cisco Catalyst Series 9105AXW and 9105AXWT Wireless Access Points
8 Performing a Pre-Installation Configuration
Note Performing a pre-installation configuration is an optional procedure. H owever, performing this procedure ensures that your access point installation and initial operation go as expected. If your network controller is properly configured, you can install your access point in its final location and connect it to the network from there. See the " Deploying the Access Point on the Wireless N etwork" section on page 24 for details.
The pre-installation configuration setup is illustrated in Figure 9. Figure 9 Pre-Installation Configuration Setup

For pre-installation configuration, perform the following steps:

Step 1

M ake sure that the Cisco Wireless Controller DS port is connected to the network. Use the procedure for CLI or web-browser interface as described in the appropriate Cisco Wireless Controller guide.
a. M ake sure that access points have Layer 3 connectivity to the Cisco Wireless Controller M anagement and AP-M anager Interface.
b. Configure the switch to which your access point is to attach. See the Cisco W ireless Controller Configuration G uide for the release you are using, for additional information.
c. Set the Cisco Wireless Controller as the primary so that new access points always join with it.

Cisco Catalyst Series 9105AXW and 9105AXWT Wireless Access Points

d. M ake sure DH CP is enabled on the network. The access point must receive its IP address through DH CP.

Note An 802.11ax Cisco AP will be assigned an IP address from the DH CP server only if a default router (gateway) is configured on the DH CP server (enabling the AP to receive its gateway IP address) and the gateway ARP is resolved.
e. CAPWAP UDP ports must not be blocked in the network. f. The access point must be able to find the IP address of the controller. This can be accomplished using DH CP,
DN S, or IP subnet broadcast. This guide describes the DH CP method to convey the controller IP address. For other methods, refer to the product documentation. See also the " Configuring DH CP O ption 43" section on page 27 for more information.

Note The access point requires a gigabit Ethernet (GbE) link to prevent the Ethernet port from becoming a bottleneck for traffic because wireless traffic speeds exceed transmit speeds of a 10/100 Ethernet port.

Step 2

Apply power to the access point. See Powering the Access Point, page 23.
a. As the access point attempts to connect to the controller, the status LED alternates between red and green. This can take up to 5 minutes.

Note If the access point remains in this mode for more than five minutes, it indicates that the access point is unable to find the primary Cisco Wireless Controller. Check the connection between the access point and the Cisco Wireless Controller and be sure that they are on the same subnet.

Step 3 Step 4 Step 5

b. If the access point shuts down, check the power source.
c. After the access point finds the Cisco Wireless Controller, it attempts to download the new operating system code if the access point code version differs from the Cisco Wireless Controller code version. While this is happening, the Status LED blinks blue.
d. If the operating system download is successful, the access point reboots.
Configure the access point if required. Use the controller CLI, controller GUI, or Cisco Prime Infrastructure to customize the access-point-specific 802.11ax network settings.
If the pre-installation configuration is successful, the Status LED is green indicating normal operation. Disconnect the access point and mount it at the location at which you intend to deploy it on the wireless network.
If your AP does not indicate normal operation, turn it off and repeat the pre-installation configuration.

Note When you are installing a Layer 3 access point on a different subnet than the Cisco Wireless Controller, be sure that a DH CP server is reachable from the subnet on which you will be installing the access point, and that the subnet has a route back to the Cisco Wireless Controller. Also be sure that the route back to the Cisco Wireless Controller has destination UDP ports 5246 and 5247 open for CAPWAP communications. Ensure that the route back to the primary, secondary, and tertiary controller allows IP packet fragments. Finally, be sure that if address translation is used, that the access point and the Cisco Wireless Controller have a static 1-to-1 N AT to an outside address. (Port Address Translation is not supported.)

Cisco Catalyst Series 9105AXW and 9105AXWT Wireless Access Points

9 M ounting the Access Point
Cisco Catalyst 9105AXW series access points can be mounted directly on a wall or on an electrical or network box, to numerous global wall junction standards.

Table 1

Access Point M ounting Options

Type of M ounting M ounting the AP directly on a Wall, page 20 M ounting the AP on an Electrical Junction Box, page 20 M ounting the AP on a Wall using the Spacer, page 21 M ounting the AP on an Electrical Junction Box using the Spacer, page 21
1. Mount the AP using no less than four screw holes on a bracket.

M ounting Bracket and Kit AIR -AP-BR AC KET -W 4 1
AIR -AP-BR AC KET -W 4 C9105AXW-KIT spacer kit.

When mounting the AP in areas where there is a possibility of the AP being knocked off the mounting bracket, use the lock hasp on the back of the AP to lock it to the bracket.

M ounting the AP directly on a W all
To mount the AP on a wall, follow these steps:

Step 1 Step 2
Step 3 Step 4

Fasten the wall-mount bracket (AIR-AP-BRACKET-W4) to the wall, using two M 3.5X32mm screws. Ensure that the side having the Mount Arrows Up label is facing outwards, and the bracket is oriented vertically as indicated by the arrows.
Connect the power and network cables to the AP.
If you are unable to connect a PoE cable to the port on the back of the AP, then: a. O n the back of the AP, use an RJ45 jumper cable to connect the PoE port to the Pass-Through port. This
jumper cable is available as part of the spacer kit (C9105AXW-KIT=). b. Connect the PoE supply cable to the Pass-Through port on the base of the AP.
This connection sends power internally from the Pass-Through port on the base, to the Pass-Through port on the back, and then though the jumper cable into the PoE port on the back.
M ount the AP onto the wall-mount bracket. For this, align the AP with the bracket and then offset the AP around � inch above the bracket.
Fasten the AP to the bracket using the M 2 x 5.5mm Torx security screw. Cover it with the mylar label.

M ounting the AP on an Electrical Junction Box
To mount the AP on an electrical junction box, follow these steps:

Step 1 Step 2

Fasten the wall-mount bracket (AIR-AP-BRACKET-W4), using two #6-32 x 0.81 inch machine screws, to the electrical junction box. Ensure that the side having the Mount Arrows Up label is facing outwards, and the bracket is oriented vertically as indicated by the arrows.
Connect the power and network cables to the AP.

Cisco Catalyst Series 9105AXW and 9105AXWT Wireless Access Points

Step 3 Step 4

If you are unable to connect a PoE cable to the port on the back of the AP, then: a. O n the back of the AP, use an RJ45 jumper cable to connect the PoE port to the Pass-Through port. This
jumper cable is available as part of the spacer kit (C9105AXW-KIT=). b. Connect the PoE supply cable to the Pass-Through port on the base of the AP.
This connection sends power internally from the Pass-Through port on the base, to the Pass-Through port on the back, and then though the jumper cable into the PoE port on the back.
M ount the AP onto the wall-mount bracket. For this, align the AP with the bracket and then offset the AP around � inch above the bracket.
Fasten the AP to the bracket using the M 2 x 5.5mm Torx security screw. Cover it with the mylar label.

M ounting the AP on a W all using the Spacer
To mount the AP on a wall, using a spacer box, follow these steps:

Step 1 Step 2 Step 3

Fasten the spacer box to the wall, using four M 3.5 x 32mm screws. Ensure that the side having the Mount Arrows Up label is facing outwards, and the box is oriented vertically as indicated by the arrows.
Fasten the wall-mount bracket (AIR-AP-BRACKET-W4) to the spacer box, using two M 3X8mm tapping screws. Ensure that the side having the Mount Arrows Up label is facing outwards, and the bracket is oriented vertically as indicated by the arrows.
Connect the power and network cables to the AP.
If you are unable to connect a PoE cable to the port on the back of the AP, then:
a. O n the back of the AP, use an RJ45 jumper cable to connect the PoE port to the Pass-Through port. This jumper cable is available as part of the spacer kit (C9105AXW-KIT).
b. Connect the PoE supply cable to the Pass-Through port on the base of the AP.
This connection sends power internally from the Pass-Through port on the base, to the Pass-Through port on the back, and then though the jumper cable into the PoE port on the back.

Note The punch-out holes on the spacer box can be used for routing cables. H owever, an RJ45 connector will not fit through these holes. If this is required, you must first route a cable through the hole and then crimp an RJ45 connector on to the cable.

Step 4 Step 5

M ount the AP onto the wall-mount bracket. For this, align the AP with the bracket and then offset the AP around � inch above the bracket.
Fasten the AP to the bracket using the M 2 x 5.5mm Torx security screw. Cover it with the mylar label.

M ounting the AP on an Electrical Junction Box using the Spacer
To mount the AP on an electrical junction box, using a spacer box, follow these steps:
Step 1 Fasten the wall-mount bracket (AIR-AP-BRACKET-W4) to the spacer box, using two M 3X8mm pan head tapping screws. Ensure that the side having the Mount Arrows Up label facing outwards, and the bracket oriented vertically as indicated by the arrows.

Cisco Catalyst Series 9105AXW and 9105AXWT Wireless Access Points

Step 2 Step 3

Fasten the wall-mount bracket and spacer box assembly to the electrical junction box, using two #6-32X1.62 inch machine screws. Ensure that the side having the Mount Arrows Up label is facing outwards, and the box is oriented vertically as indicated by the arrows.
Connect the power and network cables to the AP.
If you are unable to connect a PoE cable to the port on the back of the AP, then:
a. O n the back of the AP, use an RJ45 jumper cable to connect the PoE port to the Pass-Through port. This jumper cable is available as part of the spacer kit C9105AXW-KIT.
b. Connect the PoE supply cable to the Pass-Through port on the base of the AP.
This connection sends power internally from the Pass-Through port on the base, to the Pass-Through port on the back, and then though the jumper cable into the PoE port on the back.

Step 4 Step 5

M ounting the Kit C9105AXW T_COVER= to the AP
To mount the Kit C9105AXWT_CO VER= to the AP, follow these steps:

Step 1
Step 2 Step 3

Connect the power and network cables to the AP.
a. O n the back of the AP, use an RJ45 jumper cable to connect the PoE port to the Pass-Through port. This jumper cable is available as part of the teleworker kit (C9105AXWT_CO VER=). Bend the cable as shown in Figure 10.
b. Connect the PoE supply cable to the pass-through port on the base of the AP.
This connection sends power internally from the Pass-Through port on the base, to the Pass-Through port on the back, and then though the jumper cable into the PoE port on the back.
M ount the AP onto the bottom cover. For this, align the AP with the bottom cover and then offset the AP around � inch above the cover. Push the cover upwards to align with the AP.
Fasten the AP to the bracket using the M 2 x 5.5mm Torx security screw. Cover it with the mylar label.

Cisco Catalyst Series 9105AXW and 9105AXWT Wireless Access Points Figure 10 M ounting the C9105AXWT_COVER to the AP

1 M ylar cover to cover the Philips screw slot 2 M 2 x 5.5mm Philips screw

3 RJ-45 jumper cable 4 Bottom cover with rubber feet

1 0 Pow ering the Access Point
The AP can be powered only through Power-over-Ethernet (PoE) using the following: 802.3at (PoE+): Any 802.3at (30.0 W) compliant switch port or Cisco Power Injector AIR-PWRINJ6= 802.3af: Any 802.3af (15.4 W) compliant switch port or Cisco Power Injector AIR-PWRINJ5=

Note If 802.3af is used, the USB port and LAN PSE1 port will be off.
802.3bt: Any 802.3bt compliant switch port Cisco Universal PoE (Cisco UPOE)
1 1 Configuring and Deploying the Access Point
This section describes how to connect the access point to a controller. Because the configuration process takes place on the controller, see the Cisco Wireless Controller Configuration Guide for additional information.

Cisco Catalyst Series 9105AXW and 9105AXWT Wireless Access Points

The Controller Discovery Process

Note � The controller must be running release 8.10.105.0 or IO S-XE 17.3.x to support C9105AXW models. For more information, visit the access point data sheet available on Cisco.com at https://www.cisco.com/c/en/us/products/collateral/wireless/catalyst-9100ax-access-points/datasheet-c78-744 062.html.
� You cannot edit or query any access point using the controller CLI if the name of the access point contains a space.
� M ake sure that the controller is set to the current time. If the controller is set to a time that has already occurred, the access point might not join the controller because its certificate may not be valid for that time.

Access points must be discovered by a controller before they can become an active part of the network. The access point supports these controller discovery processes:
Locally stored controller IP address discovery--If the access point was previously joined to a controller, the IP addresses of the primary, secondary, and tertiary controllers are stored in the access point non-volatile memory. This process of storing controller IP addresses on an access point for later deployment is called priming the access point. For more information about priming, see the "Performing a Pre-Installation Configuration" section on page 18.
DHCP server discovery--This feature uses DHCP option 43 to provide controller IP addresses to the access points. Cisco switches support a DHCP server option that is typically used for this capability. For more information about DHCP option 43, see the "Configuring DHCP Option 43" section on page 27.
DNS discovery--The access point can discover controllers through your domain name server (DNS). For the access point to do so, you must configure your DNS to return controller IP addresses in response to CISCO-CAPWAP-CONTROLLER.localdomain, where localdomain is the access point domain name. Configuring the CISCO-CAPWAP-CONTROLLER provides backwards compatibility in an existing customer deployment. When an access point receives an IP address and DNS information from a DHCP server, it contacts the DNS to resolve CISCO-CAPWAP-CONTROLLER.localdomain. When the DNS sends a list of controller IP addresses, the access point sends discovery requests to the controllers.

Deploying the Access Point on the W ireless Netw ork
After you have mounted the access point, follow these steps to deploy it on the wireless network:

Step 1 Step 2

Connect and power up the access point.
O bserve the access point LED (for LED descriptions, see " Checking the Access Point LEDs" section on page 25).
a. When you power up the access point, it begins a power-up sequence that you can verify by observing the access point LED. If the power-up sequence is successful, the discovery and join process begins. During this process, the LED blinks sequentially green, red, and off. When the access point has joined a controller, the LED is green if no clients are associated or blue if one or more clients are associated.
b. If the LED is not on, the access point is most likely not receiving power.
c. If the LED blinks sequentially for more than 5 minutes, the access point is unable to find its primary, secondary, and tertiary Cisco Wireless Controller. Check the connection between the access point and the Cisco Wireless Controller, and be sure the access point and the Cisco Wireless Controller are either on the same subnet or that the access point has a route back to its primary, secondary, and tertiary Cisco Wireless Controller. Also, if the access point is not on the same subnet as the Cisco Wireless Controller, be sure that there is a properly configured DH CP server on the same subnet as the access point. See the " Configuring DH CP O ption 43" section on page 27 for additional information.

Cisco Catalyst Series 9105AXW and 9105AXWT Wireless Access Points

Step 3 Reconfigure the Cisco Wireless Controller so that it is not the primary controller.
Note A primary Cisco Wireless Controller should be used only for configuring access points and not in a working network.

1 2 Checking the Access Point LEDs
The location of the access point status LED is shown in Figure 7.

Note Regarding LED status colors, it is expected that there will be small variations in color intensity and hue from unit to unit. This is within the normal range of the LED manufacturer's specifications and is not a defect. H owever, the intensity of the LED can be changed through the controller.

The access point status LED indicates various conditions and are described in Table 2.

Table 2

LED Status Indications

M essage Type Association status
Boot loader status Boot loader error Operating status
Access point operating system errors

LED State

M essage M eaning

Green

Normal operating condition, but no wireless client associated

Blue

Normal operating condition, at least one wireless client association

Green

Executing boot loader

Blinking Green

Boot loader signing verification failure

Blinking Blue

Software upgrade in progress

Alternating between Green and Discovery/join process in progress Red

Cycling through

General warning; insufficient inline power

Red-Off-Green-Off-Blue-Off

Cisco Catalyst Series 9105AXW and 9105AXWT Wireless Access Points
1 3 M iscellaneous Usage and Configuration Guidelines
Using the M ode Button
Using the Mode button (see Figure 8) you can: Reset the AP to the default factory-shipped configuration. Clear the AP internal storage, including all configuration files. To use the mode button, press, and keep pressed, the mode button on the access point during the AP boot cycle. Wait until the AP console shows a seconds counter. Once the counter indicates the number of seconds the mode button is pressed, the AP status LED changes to blinking red. Then: To reset the AP to the default factory-shipped configuration, keep the mode button pressed for less than 20
seconds. The AP configuration files are cleared. This resets all configuration settings to factory defaults, including passwords, the IP address, and the SSID. To clear the AP internal storage, including all configuration files, keep the mode button pressed for more than 20 seconds, but less than 60 seconds.
Note If the mode button is pressed for more than 30 seconds but less than 60 seconds, the FIPS mode flag is also cleared during the full factory reset of the AP. The FIPS flag when set disables console access.
The AP status LED changes from Blue to Red, and all the files in the AP storage directory are cleared. If you keep the mode button pressed for more than 60 seconds, the mode button is assumed faulty and no changes are made.
Troubleshooting the Access Point to Cisco Controller Join Process
Note As specified in the Cisco W ireless Solutions Softw are Com patibility M atrix , ensure that your controller is running controller software release 8.10.105.0 or IO S-XE 17.3.x or later to support C9105AXW.
Access points can fail to join a controller for many reasons: a RADIUS authorization is pending; self-signed certificates are not enabled on the controller; the access point and the controller regulatory domains don't match, and so on. Controller software enables you to configure the access points to send all CAPWAP-related errors to a syslog server. You do not need to enable any debug commands on the controller because all of the CAPWAP error messages can be viewed from the syslog server itself. The state of the access point is not maintained on the controller until it receives a CAPWAP join request from the access point. Therefore, it can be difficult to determine why the CAPWAP discovery request from a certain access point was rejected. In order to troubleshoot such joining problems without enabling CAPWAP debug commands on the controller, the controller collects information for all access points that send a discovery message to it and maintains information for any access points that have successfully joined it. The controller collects all join-related information for each access point that sends a CAPWAP discovery request to the controller. Collection begins with the first discovery message received from the access point and ends with the last configuration payload sent from the controller to the access point. When the controller is maintaining join-related information for the maximum number of access points, it does not collect information for any more access points.
26

Cisco Catalyst Series 9105AXW and 9105AXWT Wireless Access Points
An access point sends all syslog messages to IP address 255.255.255.255 by default. You can also configure a DHCP server to return a syslog server IP address to the access point using option 7 on the server. The access point then starts sending all syslog messages to this IP address. When the access point joins a controller for the first time, the controller sends the global syslog server IP address (the default is 255.255.255.255) to the access point. After that, the access point sends all syslog messages to this IP address until it is overridden by one of the following scenarios: The access point is still connected to the same controller, and the global syslog server IP address configuration on
the controller has been changed using the config ap syslog host global syslog_server_IP_address command. In this case, the controller sends the new global syslog server IP address to the access point. The access point is still connected to the same controller, and a specific syslog server IP address has been configured for the access point on the controller using the config ap syslog host specific Cisco_AP syslog_server_IP_address command. In this case, the controller sends the new specific syslog server IP address to the access point. The access point is disconnected from the controller and joins another controller. In this case, the new controller sends its global syslog server IP address to the access point. Whenever a new syslog server IP address overrides the existing syslog server IP address, the old address is erased from persistent storage, and the new address is stored in its place. The access point also starts sending all syslog messages to the new IP address provided the access point can reach the syslog server IP address. You can configure the syslog server for access points and view the access point join information from the controller CLI.
Important Information for Controller-based Deployments
Keep these guidelines in mind when you use C9105AXW series access point: The access point can only communicate with Cisco wireless controllers. The access point does not support Wireless Domain Services (WDS) and cannot communicate with WDS devices.
However, the controller provides functionality equivalent to WDS when the access point joins it. CAPWAP does not support Layer 2. The access point must get an IP address and discover the controller using Layer
3, DHCP, DNS, or IP subnet broadcast. The access point console port is enabled for monitoring and debug purposes. All configuration commands are
disabled when the access point is connected to a controller.
Configuring DHCP Option 43
You can use DHCP Option 43 to provide a list of controller IP addresses to the access points, enabling them to find and join a controller. The following is a DHCP Option 43 configuration example on a Windows 2003 Enterprise DHCP server for use with Cisco Catalyst lightweight access points. For other DHCP server implementations, consult product documentation for configuring DHCP Option 43. In Option 43, you should use the IP address of the controller management interface.
Note DH CP O ption 43 is limited to one access point type per DH CP pool. You must configure a separate DH CP pool for each access point type.
27

Cisco Catalyst Series 9105AXW and 9105AXWT Wireless Access Points

The C9105AXW series access point uses the type-length-value (TLV) format for DHCP Option 43. DHCP servers must be programmed to return the option based on the access point DHCP Vendor Class Identifier (VCI) string (DHCP Option 43). The VCI string for the C9105AXW series access point is:
Cisco AP C9105AXW
The format of the TLV block is listed below: Type--0xf1 (decimal 241) Length--Number of controller IP addresses * 4 Value--IP addresses of the WLC management interfaces listed sequentially in hex
To configure DHCP Option 43 in the embedded Cisco IOS DHCP server, follow these steps:

Step 1 Step 2

Enter configuration mode at the Cisco IO S CLI.
Create the DH CP pool, including the necessary parameters such as default router and name server. A DH CP scope example is as follows:
ip dhcp pool <pool name> network <IP Network> <Netmask> default-router <Default router> dns-server <DNS Server>

Where:

<pool name> is the name of the DHCP pool, such as AP9105AXW <IP Network> is the network IP address where the controller resides, such as 10.0.15.1 <Netmask> is the subnet mask, such as 255.255.255.0 <Default router> is the IP address of the default router, such as 10.0.0.1 <DNS Server> is the IP address of the DNS server, such as 10.0.10.2

Step 3 Add the option 43 line using the following syntax:
option 43 hex <hex string>

The hex string is assembled by concatenating the TLV values shown below:

Type + Length + Value

For example, suppose that there are two controllers with management interface IP addresses, 10.126.126.2 and 10.127.127.2. The type is f1(hex). The length is 2 * 4 = 8 = 08 (hex). The IP addresses translate to 0a7e7e02 and 0a7f7f02. Assembling the string then yields f1080a7e7e020a7f7f02. The resulting Cisco IOS command added to the DHCP scope is option 43 hex f1080a7e7e020a7f7f02.

Cisco Catalyst Series 9105AXW and 9105AXWT Wireless Access Points
1 4 FAQs
W hat is 802.11ax?
The IEEE 802.11ax standard, also known as the High-Efficiency Wireless (HEW) or Wi-Fi 6, builds off of the 802.11ac and delivers a better experience in typical environments, and a more predictable performance for advanced applications such as 4K or 8K video, high-density high-definition collaboration applications, all-wireless offices and Internet-of-Things (IoT). 802.11ax is designed to use both 2.4Ghz and the 5GHz bands, unlike prior standards.
W hat is Cisco M ultigigabit Ethernet?
Cisco Multigigabit Ethernet (mGig) is a unique Cisco innovation also available in the Cisco Catalyst 9105AXW series access point. With the increasing popularity of 802.11ax and new wireless applications, wireless devices now require more network bandwidth. Hence, there is a need for a technology that supports speeds higher than 1 Gbps on all cabling infrastructure. Cisco Multigigabit technology allows you to achieve bandwidth speeds from 1 to 10 Gbps over traditional Cat 5e cabling or newer. The C9105AXW AP supports up to 2.5 Gbps using mGig. For more information see the following Cisco Multigigabit FAQ document: http://www.cisco.com/c/dam/en/us/solutions/collateral/enterprise-networks/catalyst-multigigabit-switching/multigiga bit-ethernet-technology.pdf
1 5 Related Documentation
All user documentation for the Cisco Catalyst 9105AXW series access point is available at the following URL: https://www.cisco.com/c/en/us/support/wireless/catalyst-9100ax-access-points/series.html For detailed information and guidelines for configuring and deploying your access point in a wireless network, see the following documentation: Cisco Catalyst 9105AXW Series Access Point Deployment Guide, at the following URL:
https://www.cisco.com/c/en/us/products/wireless/catalyst-9100ax-access-points/datasheet-listing.html Cisco Wireless Controller Configuration Guide, Release 8.10, at the following URL:
http://www.cisco.com/c/en/us/td/docs/wireless/controller/8-10/config-guide/b_cg810.html Cisco Catalyst 9800 Series Wireless Controller Software Configuration Guide, Cisco IOS XE Amsterdam 17.3.x, at
the following URL: https://www.cisco.com/c/en/us/td/docs/wireless/controller/9800/17-3/config-guide/b_wl_17_3_cg.html
29

Cisco Catalyst Series 9105AXW and 9105AXWT Wireless Access Points
1 6 Declarations of Conformity and Regulatory Information
This section provides declarations of conformity and regulatory information for the Cisco Catalyst 9105AXW Series Access Points. You can find additional information at this URL: www.cisco.com/go/aironet/compliance
M anufacturers Federal Communication Commission Declaration of Conformity Statement

Access Point M odels C9105AXW-B C9105AXW-EWC-B C9105AXWT-B

Certification Number LDK-SMST9105AXW LDK-SMST9105AXW LDK-SMST9105AXW

Manufacturer:
Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA
This device complies with Part 15 rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and radiates radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference. However, there is no guarantee that interference will not occur. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from which the receiver is connected.
Consult the dealer or an experienced radio/TV technician.

Cisco Catalyst Series 9105AXW and 9105AXWT Wireless Access Points

Caution

The Part 15 radio device operates on a non-interference basis with other devices operating at this frequency when using the integrated antennas. Any changes or modification to the product not expressly approved by Cisco could void the user's authority to operate this device.

VCCI Statement for Japan

W arning

This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual.

Guidelines for Operating Cisco Catalyst Access Points in Japan
This section provides guidelines for avoiding interference when operating Cisco Catalyst access points in Japan. These guidelines are provided in both Japanese and English.
Japanese Translation

208697

03-6434-6500
31

Cisco Catalyst Series 9105AXW and 9105AXWT Wireless Access Points
English Translation
This equipment operates in the same frequency bandwidth as industrial, scientific, and medical devices such as microwave ovens and mobile object identification (RF-ID) systems (licensed premises radio stations and unlicensed specified low-power radio stations) used in factory production lines.
1. Before using this equipment, make sure that no premises radio stations or specified low-power radio stations of RF-ID are used in the vicinity.
2. If this equipment causes RF interference to a premises radio station of RF-ID, promptly change the frequency or stop using the device; contact the number below and ask for recommendations on avoiding radio interference, such as setting partitions.
3. If this equipment causes RF interference to a specified low-power radio station of RF-ID, contact the number below. Contact Number: 03-6434-6500
Statement 371-- Pow er Cable and AC Adapter

English Translation
When installing the product, please use the provided or designated connection cables/power cables/AC adaptors. Using any other cables/adaptors could cause a malfunction or a fire. Electrical Appliance and Material Safety Law prohibits the use of UL-certified cables (that have the "UL" shown on the code) for any other electrical devices than products designated by CISCO. The use of cables that are certified by Electrical Appliance and Material Safety Law (that have "PSE" shown on the code) is not limited to CISCO-designated products.

Industry Canada
Access Point M odels C9105AXW-A C9105AXW-EWC-A C9105AXWT-A

Certification Number 2461N-SMST9105AXW 2461N-SMST9105AXW 2461N-SMST9105AXW

Canadian Compliance Statement
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le pr�sent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autoris�e aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radio�lectrique subi, m�me si le brouillage est susceptible d'en compromettre le fonctionnement.

Cisco Catalyst Series 9105AXW and 9105AXWT Wireless Access Points

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conform�ment � la r�glementation d'Industrie Canada, le pr�sent �metteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inf�rieur) approuv� pour l'�metteur par Industrie Canada. Dans le but de r�duire les risques de brouillage radio�lectrique � l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonn�e �quivalente (p.i.r.e.) ne d�passe pas l'intensit� n�cessaire � l'�tablissement d'une communication satisfaisante.
This radio transmitter has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le pr�sent �metteur radio a �t� approuv� par Industrie Canada pour fonctionner avec les types d'antenne �num�r�s ci-dessous et ayant un gain admissible maximal et l'imp�dance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est sup�rieur au gain maximal indiqu�, sont strictement interdits pour l'exploitation de l'�metteur.

Table 3

List of Internal Antennas Supported on C9105AXW and 9105AXWT

Antenna Type

Antenna Gain

Antenna Impedance

Dual-Band Omni

2.4 GHz--3 dBi 5 GHz--5 dBi

50 ohms

Single-Band Omni

3 dBi

50 ohms

Operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems. La bande 5 150-5 250 MHz est r�serv�s uniquement pour une utilisation � l'int�rieur afin de r�duire les risques de brouillage pr�judiciable aux syst�mes de satellites mobiles utilisant les m�mes canaux.
Users are advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Les utilisateurs �tes avis�s que les utilisateurs de radars de haute puissance sont d�sign�s utilisateurs principaux (c.-�-d., qu'ils ont la priorit�) pour les bandes 5 250-5 350 MHz et 5 650-5 850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.

European Community, Sw itzerland, Norw ay, Iceland, and Liechtenstein
Access Point Models:
C9105AXW-E C9105AXW-EWC-E C9105AXWT-E

Note This equipment is intended to be used in all EU and EFTA countries. O utdoor use may be restricted to certain frequencies and/or may require a license for operation. For more details, contact Cisco Corporate Compliance.
The product carries the CE Mark:

Cisco Catalyst Series 9105AXW and 9105AXWT Wireless Access Points

Declaration of Conformity for RF Exposure
This section contains information on compliance with guidelines related to RF exposure.
Generic Discussion on RF Exposure
The Cisco products are designed to comply with the following national and international standards on Human Exposure to Radio Frequencies:
US 47 Code of Federal Regulations Part 2 Subpart J
American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers / IEEE C 95.1 (99)
International Commission on Non Ionizing Radiation Protection (ICNIRP) 98
Ministry of Health (Canada) Safety Code 6. Limits on Human Exposure to Radio Frequency Fields in the range from 3kHz to 300 GHz
Australia Radiation Protection Standard
To ensure compliance with various national and international Electromagnetic Field (EMF) standards, the system should only be operated with Cisco approved antennas and accessories.
This Device M eets International Guidelines for Exposure to Radio Waves
The C9105AXW series device includes a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves (radio frequency electromagnetic fields) recommended by international guidelines. The guidelines were developed by an independent scientific organization (ICNIRP) and include a substantial safety margin designed to ensure the safety of all persons, regardless of age and health.
As such the systems are designed to be operated as to avoid contact with the antennas by the end user. It is recommended to set the system in a location where the antennas can remain at least a minimum distance as specified from the user in accordance to the regulatory guidelines which are designed to reduce the overall exposure of the user or operator.

MPE 0.25 mW/cm2

Separation Distance Distance 30 cm (12 inches)

Limit 1.00 mW/cm2

The World Health Organization has stated that present scientific information does not indicate the need for any special precautions for the use of wireless devices. They recommend that if you are interested in further reducing your exposure then you can easily do so by reorienting antennas away from the user or placing he antennas at a greater separation distance then recommended.
This Device M eets FCC Guidelines for Exposure to Radio Waves
The C9105AXW series device includes a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves (radio frequency electromagnetic fields) as referenced in FCC Part 1.1310. The guidelines are based on IEEE ANSI C 95.1 (92) and include a substantial safety margin designed to ensure the safety of all persons, regardless of age and health.

Cisco Catalyst Series 9105AXW and 9105AXWT Wireless Access Points

As such the systems are designed to be operated as to avoid contact with the antennas by the end user. It is recommended to set the system in a location where the antennas can remain at least a minimum distance as specified from the user in accordance to the regulatory guidelines which are designed to reduce the overall exposure of the user or operator.
The device has been tested and found compliant with the applicable regulations as part of the radio certification process.

MPE 0.246 mW/cm2

Separation Distance Distance 20 cm (7.87 inches)

Limit 1.00 mW/cm2

The US Food and Drug Administration has stated that present scientific information does not indicate the need for any special precautions for the use of wireless devices. The FCC recommends that if you are interested in further reducing your exposure then you can easily do so by reorienting antennas away from the user or placing the antennas at a greater separation distance then recommended or lowering the transmitter power output.
This Device M eets the Industry Canada Guidelines for Exposure to Radio Waves
The C9105AXW series device includes a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves (radio frequency electromagnetic fields) as referenced in Health Canada Safety Code 6. The guidelines include a substantial safety margin designed into the limit to ensure the safety of all persons, regardless of age and health.
As such the systems are designed to be operated as to avoid contact with the antennas by the end user. It is recommended to set the system in a location where the antennas can remain at least a minimum distance as specified from the user in accordance to the regulatory guidelines which are designed to reduce the overall exposure of the user or operator.

Frequency 2.4 GHz 5 GHz

Separation Distance

MPE 2.46 W/m2

Distance 20 cm (7.87 inches)

3.05 W/m2

Limit 5.4 W/m2 9.76 W/m2

Health Canada states that present scientific information does not indicate the need for any special precautions for the use of wireless devices. They recommend that if you are interested in further reducing your exposure you can easily do so by reorienting antennas away from the user, placing the antennas at a greater separation distance than recommended, or lowering the transmitter power output.
Cet appareil est conforme aux directives internationales en mati�re d'exposition aux fr�quences radio�lectriques
Cet appareil de la gamme C9105AXW comprend un �metteur-r�cepteur radio. Il a �t� con�u de mani�re � respecter les limites en mati�re d'exposition aux fr�quences radio�lectriques (champs �lectromagn�tiques de fr�quence radio), recommand�es dans le code de s�curit� 6 de Sant� Canada. Ces directives int�grent une marge de s�curit� importante destin�e � assurer la s�curit� de tous, ind�pendamment de l'�ge et de la sant�.

Cisco Catalyst Series 9105AXW and 9105AXWT Wireless Access Points

Par cons�quent, les syst�mes sont con�us pour �tre exploit�s en �vitant que l'utilisateur n'entre en contact avec les antennes. Il est recommand� de poser le syst�me l� o� les antennes sont � une distance minimale telle que pr�cis�e par l'utilisateur conform�ment aux directives r�glementaires qui sont con�ues pour r�duire l'exposition g�n�rale de l'utilisateur ou de l'op�rateur.

Fr�quence 2.4 GHz 5 GHz

Distance d'�loignement

MPE 2.46 W/m2 3.05 W/m2

Distance 20 cm (7.87 inches)

Limite 5.4 W/m2 9.76 W/m2

Sant� Canada affirme que la litt�rature scientifique actuelle n'indique pas qu'il faille prendre des pr�cautions particuli�res lors de l'utilisation d'un appareil sans fil. Si vous voulez r�duire votre exposition encore davantage, selon l'agence, vous pouvez facilement le faire en r�orientant les antennes afin qu'elles soient dirig�es � l'�cart de l'utilisateur, en les pla�ant � une distance d'�loignement sup�rieure � celle recommand�e ou en r�duisant la puissance de sortie de l'�metteur.
Additional Information on RF Exposure
You can find additional information on the subject at the following links:
Cisco Systems Spread Spectrum Radios and RF Safety white paper at this URL: http://www.cisco.com/warp/public/cc/pd/witc/ao340ap/prodlit/rfhr_wi.htm
FCC Bulletin 56: Questions and Answers about Biological Effects and Potential Hazards of Radio Frequency Electromagnetic Fields
FCC Bulletin 65: Evaluating Compliance with the FCC guidelines for Human Exposure to Radio Frequency Electromagnetic Fields
You can obtain additional information from the following organizations:
World Health Organization Internal Commission on Non-Ionizing Radiation Protection at this URL: www.who.int/emf
United Kingdom, National Radiological Protection Board at this URL: www.nrpb.org.uk
Cellular Telecommunications Association at this URL: www.wow-com.com
The Mobile Manufacturers Forum at this URL: www.mmfai.org

Cisco Catalyst Series 9105AXW and 9105AXWT Wireless Access Points
Administrative Rules for Cisco Catalyst Access Points in Taiw an
This section provides administrative rules for operating Cisco Catalyst access points in Taiwan. The rules for all access points are provided in both Chinese and English.
Chinese Translation
English Translation
Administrative Rules for Low-power Radio-Frequency Devices Article 12 For those low-power radio-frequency devices that have already received a type-approval, companies, business units or users should not change its frequencies, increase its power or change its original features and functions. Article 14 The operation of the low-power radio-frequency devices is subject to the conditions that no harmful interference is caused to aviation safety and authorized radio station; and if interference is caused, the user must stop operating the device immediately and can't re-operate it until the harmful interference is clear. The authorized radio station means a radio-communication service operating in accordance with the Communication Act. The operation of the low-power radio-frequency devices is subject to the interference caused by the operation of an authorized radio station, by another intentional or unintentional radiator, by industrial, scientific and medical (ISM) equipment, or by an incidental radiator.
37

Cisco Catalyst Series 9105AXW and 9105AXWT Wireless Access Points
Chinese Translation

English Translation
Low-power Radio-frequency Devices Technical Specifications

4.7 4.7.5 4.7.6
4.7.7

Unlicensed National Information Infrastructure
Within the 5.25-5.35 GHz band, U-NII devices will be restricted to indoor operations to reduce any potential for harmful interference to co-channel MSS operations.
The U-NII devices shall accept any interference from legal communications and shall not interfere the legal communications. If interference is caused, the user must stop operating the device immediately and can't re-operate it until the harmful interference is clear.
Manufacturers of U-NII devices are responsible for ensuring frequency stability such that an emission is maintained within the band of operation under all conditions of normal operation as specified in the user manual.

Operation of Cisco Catalyst Access Points in Brazil

This section contains special information for operation of Cisco Catalyst access points in Brazil.

Access Point M odels C9105AXW-Z C9105AXW-EWC-Z C9105AXWT-Z

Certification Number 02828-21-01086

Cisco Catalyst Series 9105AXW and 9105AXWT Wireless Access Points Communications, Services, and Additional Information
Figure 11 Brazil Regulatory Information
Portuguese Translation
Este equipamento n�o tem direito � prote��o contra interfer�ncia prejudicial e n�o pode causar interfer�ncia em sistemas devidamente autorizados.
English Translation
This equipment is not entitled to the protection from harmful interference and may not cause interference with duly authorized systems.
Declaration of Conformity Statements
All the Declaration of Conformity statements related to this product can be found at the following location: http://www.ciscofax.com
Communications, Services, and Additional Information
To receive timely, relevant information from Cisco, sign up at Cisco Profile Manager. To get the business impact you're looking for with the technologies that matter, visit Cisco Services. To submit a service request, visit Cisco Support. To discover and browse secure, validated enterprise-class apps, products, solutions and services, visit Cisco
Marketplace. To obtain general networking, training, and certification titles, visit Cisco Press. To find warranty information for a specific product or product family, access Cisco Warranty Finder.
Cisco Bug Search Tool
Cisco Bug Search Tool (BST) is a web-based tool that acts as a gateway to the Cisco bug tracking system that maintains a comprehensive list of defects and vulnerabilities in Cisco products and software. BST provides you with detailed defect information about your products and software. � 2021 Cisco Systems, Inc. All rights reserved.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1721R)
39

Cisco Catalyst Series 9105AXW and 9105AXWT Wireless Access Points 40