SOUNDPEATS TrueAir2 Wireless Earbuds User Guide

Product Information

Manufacturer: Shenzhen SoundSOUL Information Technology Company Limited

Address: Room 1308-1309, Building B, Huihai Square, Chuangye Road, Longhua District, Shenzhen, China. 518109

Website: www.soundpeatsaudio.com

Support Email: support@soundpeatsaudio.com

FCC ID: 2AFTU-DD012

Model: TrueAir2

Getting Started

Pairing

1. The earbuds automatically pair to each other after being taken out from the charging case. The light on the main earbud flashes in white and red, while the second earbud stays in white.
2. Activate Bluetooth on your device and select "SOUNDPEATS TrueAir2" from the Bluetooth list to pair.

Reset

If you experience issues connecting the earbuds to each other or to your device, follow these steps:

1. Clear the pairing record between the earbuds and all your devices.
2. Place both earbuds back into the charging case and ensure they are charging. Press and hold both Multifunction Buttons (MFBs) for 10 seconds until both indicators flash white twice.

Wearing

Refer to the diagram for proper wearing instructions. [Diagram showing how to wear earbuds]

Product Diagram

[Diagram of the SOUNDPEATS TrueAir2 earbuds and charging case with labeled parts]

Button Controls

• Power On: Auto (take out from charging case) or Manually (press and hold MFB for 1.5s)
• Power Off: Auto (place back into charging case) or Manually (press and hold MFB for 10s)
• Play/Pause: Double tap the MFB
• Volume Down: Single tap the left MFB
• Volume Up: Single tap the right MFB
• Previous Track: Press and hold the left MFB for 1.5s
• Next Track: Press and hold the right MFB for 1.5s
• Answer/Hang Up Call: Double tap the touch button
• Reject Phone Call: Press and hold the MFB for 1.5s
• Switch Between Two Calls: Press and hold the MFB for 2s
• Activate Voice Assistant: Triple tap the MFB
• Manually Enter Pairing Mode: Press and hold the MFB for 6s

Q&A

• Q1: What do the charging LEDs tell while charging the case?
  The LEDs stay on while charging and turn off after fully charged.
• Q2: Why are the earbuds still connected to my phone after placing them back in the case?
  1. The charging case might be out of battery. The case will not turn off the earbuds if its battery is dead.
  2. Ensure the earbuds are properly seated in the charging case and that the charging contacts on both the earbuds and the case are clean. If not, clean the contacts with a microfiber cloth.
• Q3: The battery life is not as advertised?
  A single charge provides approximately 5 hours of playtime with average use. The charging case provides an additional 4 recharges, for a total of up to 25 hours.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.