Jack Sealey Limited. 1. SAFETY. INSTRUCTIONS FOR: SUpER MIG WELDER. MODEL NO: SUpERMIG 180.V3. Refer to instruction manual. Wear a welding.
INSTRUCTIONS FOR
SUPERMIG WELDER
MODEL No: SUPERMIG180.V3
© Jack Sealey Limited
Original Language Version
SUPERMIG180.V3 Issue No:5(D) - 11/11/16
InstructionS For:
SUPER MIG WELDER model No: SUPERMIG 180.V3
Thank you for purchasing a Sealey Welder. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance.
IMPORTANT: BEFORE USING THIS PRODUCT, PLEASE READ THE INSTRUCTIONS CAREFULLY. MAKE CAREFUL NOTE OF SAFETY iNSTRUCTIONS, WARNINGS AND CAUTIONS. THIS PRODUCT SHOULD ONLY BE USED FOR ITS INTENDED PURPOSE. FAILURE TO DO SO MAY CAUSE DAMAGE OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY.
Refer to instruction manual
Wear a welding mask
Wear protective gloves
1.sAfeTy
1.1.
1.1.1.
1.1.2.
1.1.3.
1.1.4. 1.1.5. 1.1.6. 1.1.7. 1.1.8. 1.1.9. 1.1.10.
1.1.11.
1.2.
1.3.
ELECTRICAL SAFETY WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following: You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also recommend that a Residual Current Device (RCD) is used. It is particularly important to use an RCD with portable products that are plugged into a supply which is not protected by an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual Current Device by contacting your Sealey dealer. You must also read and understand the following instructions concerning electrical safety. The Electricity at Work Act 1989 requires that all portable electrical appliances, if used on business premises, are tested by a qualified electrician, using a Portable Appliance Tester (PAT), at least once a year. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those appliances and the safety of the appliance operators. If in any doubt about electrical safety, contact a qualified electrician. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. See 1.1.1. and 1.1.2. and use a Portable Appliance Tester. Ensure that cables are always protected against short circuit and overload. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that none is loose. Important: Ensure that the voltage marked on the appliance matches the power supply to be used and that the supply is correctly fused. DONOT pull or carry the appliance by the power cable. DONOT pull the plug from the socket by the cable. DONOTuse worn or damaged cables, plugs or connectors. Immediately have any faulty item repaired or replaced by a qualified electrician. Supermig180.V3 is a single phase machine and must be run from a minimum 16Amp supply. To achieve maximum output this model will require a 30Amp fused supply. We recommend you discuss the installation of an industrial round pin plug and socket with your electrician. Fit a plug according to the following instructions (UK only). a) Connect the GREEN/YELLOW earth wire to the earth terminal `E'. b) Connect the BROWN live wire to the live terminal `L'. c) Connect the BLUE neutral wire to the neutral terminal `N'. d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable outer insulation extends beyond the cable restraint and that the restraint is tight. When a cable extension reel is used it should be fully unwound before connection. A cable reel with an RCD fitted is recommended since any product which is plugged into the cable reel will be protected. The cross-section of the cable on the cable reel must be suitable for the unit and never lower than the cross-section of the mains cable supplied with the unit. GENERAL SAFETY DANGER! Unplug the welder from the mains power supply before performing maintenance or service. Keep the welder and cables in good condition. Take immediate action to repair or replace damaged parts. Use genuine parts and accessories only. Unapproved parts may be dangerous and will invalidate the warranty. Use an air hose to regularly blow out any dirt from the liner and keep the welder clean for best and safest performance. Check and spray the gas cup and contact tip regularly with anti-spatter spray which is available from your Sealey dealer. Locate the welder in a suitable work area. Ensure that the area has adequate ventilation as welding fumes are harmful. Keep work area clean, tidy and free from unrelated materials. Also ensure that the work area has adequate lighting and that a fire extinguisher is at hand. WARNING! Use welding head shield to protect eyes and avoid exposing skin to ultraviolet rays given off by electric arc. Wear safety welding gauntlets. Remove ill fitting clothing, remove ties, watches, rings and other loose jewellery and contain long hair. Ensure that the workpiece is correctly secured before operating the welder. Avoid unintentional contact with workpiece. Accidental or uncontrolled use of the torch may be dangerous and will wear the nozzle. Keep unauthorised persons away from the work area. Any persons working within the area must wear protective head shield and gloves. Operators must receive adequate training before using the welder. Stand correctly, keeping a good footing and balance, and ensure that the floor is not slippery. Wear non-slip shoes. Turn voltage switch to 'OFF' when not in use. DO NOT operate the welder if it or its cables are damaged and DO NOT attempt to fit any unapproved torch or other parts to the welder unit. DO NOT get welder wet or use in damp or wet locations or areas where there is condensation. DANGER! DO NOT weld near inflammable materials, solids, liquids, or gases, and DONOTweld containers or pipes which have held flammable materials or gases, liquids or solids. Avoid operating on materials cleaned with chlorinated solvents or near such solvents. DO NOT stand welder on a metal workbench, car bodywork or similar object. DO NOT touch any live metal parts of the torch or electrode while the machine is switched on. DO NOT pull the welder by the cable or the torch and DONOTbend or strain cables. Protect cables from sharp or abrasive items and DO NOT stand on them. Protect from heat. Long lengths of slack must be gathered and neatly coiled. DONOTplace cables where they could endanger other people. DO NOT touch the torch or workpiece immediately after welding as they will be very hot. Allow to cool. DO NOT operate welder while under the influence of drugs, alcohol or intoxicating medication, or if tired. When not in use store the welder in a safe, dry, childproof area. GAS SAFETY Store gas cylinders in a vertical position only and ensure that the storage area is correctly secured. DO NOT store gas cylinders in areas where temperature exceeds 50°C. DO NOT use direct heat on a cylinder. Always keep gas cylinders cool. DO NOT attempt to repair or modify any part of a gas cylinder or valve and DO NOT puncture or damage a cylinder. DO NOT obscure or remove any official cylinder labels. Always check the gas identity before use. Avoid getting gas cylinders oily or greasy. DO NOT lift a cylinder by the cap, guard or valve. Always keep caps and guards in place and close valve when not in use.
© Jack Sealey Limited
Original Language Version
SUPERMIG180.V3 Issue No:5(D) - 11/11/16
2.introduction
2.1. All our Supermig® models are suitable for welding with CO², Argon or CO2/Argon mix. Each uses a Forced Air Cooling System to slow transformer heating in order to increase duty cycle and a non-live torch to prevent the risk of accidentally striking an arc. All models are supplied with an industrial Argon/CO² regulator. Welders are illustrated with gas bottles to give an indication of size only; gas is not included. A contract for the supply of gas should be arranged with your local gas distributor.
2.2. IMPORTANT: These instructions contain information you require to prepare your machine for welding, together with a maintenance and trouble shooting section. If you have no previous experience the instructions are not intended to show you how to become a welder . Should you have no experience, we recommend that you seek training from an expert source. MIG welding is relatively easy to perform, but does require a steady hand and time practising under supervision with scrap metal as it is only with continued practice that you will achieve the desired results.
3.specification
Model No:................................................................................. Supermig180.V3 Welding Current:...................................................................................... 30 - 180A Wire Capacity - steel:................................................................................. 5 - 15kg Duty Cycle:..............100%@56Amps, 75%@65Amps, 60%@73Amps, 15%@145Amps Cooling System:...................................................................................... Forced Air Spot Welding timer.............................................................................................Yes TGoarschT:y..p..e..:.....................................................................................................................................C..O. E²u, rAorgNoonn&LiCveO-²/ABrINgoZnELm®ix Power Input.............................................................................................. 230V 1ph Absorbed power............................................................................................ 5.7kW Case size....................................................................................................... Large Weight..............................................................................................................45kg
4. assembly/PREPARATION
4.1. ASSEMBLING GAS PLATFORM: (Refer to 'P' in figs.1 & 2) Turn the welder upside down on a smooth non-abrasive surface. The welder should be turned over
by two people as it is very heavy.
4.1.1 The gas platform is held in place with 7 M6 x 10mm bolts requiring a 10mm spanner. The casing has pre-prepared threaded inserts ready to take the fixings.
Place the platform onto the base of the welder with the axle uppermost and fix in place with 3 bolts. See (X) in fig.1 below.
4.1.2 Insert the remaining four bolts through the two fixing flanges laying on the back of the welder. See (X) in fig.2. Finally, tighten all 7 bolts.
4.2. ASSEMBLING THE WHEELS: (Refer to fig.1)
4.2.1 Slide a wheel (Y) over each end of the solid axle attached to the gas platform. Slide a washer over each end of the axle and insert a split pin (Z) through the
hole in each end of the axle and bend it over to retain the wheels.
4.2.2 Bolt the two castors (W) to the front end of the base using the 8 bolts provided. The casing has pre-prepared threaded inserts ready to take the fixings. See fig.1.
4.2.3 With the assistance of another person turn the welder the right way up onto its wheels.
4.2.4 The Gas Cylinder Bracket (Item 36) can be found stored inside the wire feed compartment, in the top corner above the wire feed assembly. Remove from this
location and fix to the rear of the machine.
4.3. ASSEMBLING THE EARTH CLAMP: (Refer to fig.3) Feed the eyelet on the end of the earth lead through the hole in the clamp arm as shown in fig.3A.
4.3.1 Drop the eyelet over the terminal and firmly fix with the bolt provided as shown in fig.3B.
4.4. installing the gas cylinder. The welder is designed to accommodate small or medium sized gas cylinders up to a maximum height of 1000mm.
Contact your local Gas dealer for supply.
4.4.1 Place the gas cylinder onto the rear platform of the welder. See fig.2-P. Place one end of the fixing chain into one side of the retaining bracket. Draw the
chain around the cylinder and place it into the slot on the other side of the bracket leaving as little slack in the chain as possible.
4.5
ATTACHING THE REGULATOR. Whichever gas you are using it is advisable to 'crack' the cylinder valve before attaching the regulator.
This means opening and closing the valve very quickly in order to blow away any dust and dirt that may have accumulated in the gas outlet. Stand to one
side whilst doing this.
4.5.1 CO² gas. Ensure that the threads on the gas bottle are undamaged and free of oil and grease before attaching the regulator. (Oil or grease in the presence
of high pressure gases can be explosive). Ensure that the regulator has an undamaged gasket fitted. The regulator will screw directly to the threads on the
gas bottle. Tighten with a spanner.
4.5.2 argon gas or argon mixtures. Cylinders containing Argon gas and Argon mixtures have a female thread and will require the use of a Bull Nose
Adaptor to attach the regulator to the cylinder as indicated in fig.4. Ensure that the threads on the gas bottle are undamaged and free of oil and grease before
attaching the regulator. (Oil or grease in the presence of high pressure gases is explosive). Fit the Bull Nose Adaptor to the cylinder first and tighten with a
spanner. Ensure that the regulator has an undamaged gasket before fitting onto the Bull Nose Adaptor. Tighten with a spanner.
4.5.3 Slide a clip over each end of the gas hose supplied. Push one end of the hose onto the regulator outlet and the other end over the gas inlet spigot
on the back of the welder. See fig.2G. Tighten the clips to ensure a good seal.
4.5.4 Close the regulator valve by turning it anticlockwise before opening the cylinder valve. Stand to one side when opening the cylinder valve.
4.5.5 Set the regulator flow rate to 5-8 litres/min depending on the material to be welded, and whether there are draughts which are strong enough to disturb the
gas flow.
fig.1
fig.2
fig.3
fig.4
© Jack Sealey Limited
Original Language Version
SUPERMIG180.V3 Issue No:5(D) - 11/11/16
fig.5
fig.9
fig.6
4.8.
Fitting a 5kg reel of wire. Ensure that the wire diameter
used, is matched by the correct groove size in the drive wheel and
the correct tip size on the torch as well as the correct torch liner.
Failure to do this could cause the wire to slip and/or bind.
4.8.1. Unscrew the locking knob from the end of the spool holder (see
4.6.
CONNECT THE TORCH CABLE TO THE WELDER. Align the pins
fig.7C) and remove the spacer. Slide the reel of wire onto the spool
on the Euro connector with the socket on the welder front panel as
holder and ensure that the clutch pin at the back of the spool holder
shown in fig.5. Push the connector into the socket and rotate the
(E) engages into the guide hole in the wire reel moulding. This will
locking ring (A) clockwise so that it draws the plug into the socket
prevent the wire reel from freewheeling on the spool holder. Slide
as shown in fig.6.
the spacer onto the spool holder and retain it by screwing the knob
Note: damage to torches and cables is not covered by warranty.
into place as shown above in fig.9. Ensure that the wire is coming
off the bottom of the reel in the direction of the wire drive unit as
shown in fig.10.
fig.7
fig.10
4.7. 4.7.1
Fitting a 15kg reel of wire. Ensure that the wire diameter used, is matched by the correct groove size in the drive wheel and the correct tip size on the torch as well as the correct torch liner. Failure to do this could cause the wire to slip and/or bind. Unscrew the locking knob from the end of the spool holder (see fig.7C) and remove the spacer (B). The spacer is not required for 15kg reels of wire. Slide the reel of wire onto the spool holder and ensure that the clutch pin at the back of the spool holder (E) engages into the guide hole in the wire reel moulding. This will prevent the wire reel from freewheeling on the spool holder. Ensure that the wire is coming off the bottom of the reel in the direction of the wire drive unit as shown in fig.8 below.
fig.8
4.9.
4.9.1 4.9.2 4.9.3 4.9.4
4.9.5
FEED WIRE THROUGH TO TORCH. Referring to fig.12 open the wire feed mechanism by pushing the locking/wire tension knob (1) down to the right allowing the pressure roller carrier (2) to spring up revealing the feed roller. Ensure that the required feed groove (0.6 or 0.8) is in line with the wire path. See Section 4.12 on how to reverse or change the roller. Release the wire from the reel and cut off any bent portion ensuring that there are no burrs left on the end of the wire. Keep the wire under tension at all times to prevent it uncoiling. Straighten about 40-50mm of wire and gently push it through the flexible metal sheathed cable (3) and through the 6 or 8mm feed roller groove and on into the torch cable liner. Push down the pressure roller carrier onto the wire feed roller and hold it down. Lift up the locking/wire tension knob so that it enters the slot in the pressure roller carrier and snaps into the indent in its top surface. See fig.13. Rotate the tension knob to a medium setting i.e. between 2 and 3. Remove gas cup (fig.11-2) and contact tip (1) from end of torch as follows: a) Take torch in left hand with the torch tip facing to the right. b) Grasp gas cup firmly in your right hand. c) Turn gas cup clockwise only and pull it off end of torch tip. WARNING! do not turn gas cup anti-clockwise, as this will damage the internal spring. d) Unscrew copper contact tip (right hand thread) to remove. Check welder is switched off "0", and that the earth clamp is away from the torch tip. Connect the welder to the mains power supply and set the voltage switch to one.
© Jack Sealey Limited
Original Language Version
fig.11
SUPERMIG180.V3 Issue No:5(D) - 11/11/16
fig.12
4.12.3
4.12.4 4.12.5 4.12.6 4.12.7
The roller carrier (A) is keyed to the main drive shaft and the drive roller (B) is keyed to the carrier, see below. Place a finger onto the end of the drive shaft to prevent the carrier moving and slide the drive roller off the carrier with your other hand. The size of each wire feed groove is printed on the edge of the roller on the same side as the groove. Turn the roller over to use the other groove or use a roller with different sized grooves as required. The groove to be used should be positioned furthest away from you to be in line with the drive path. Check that the key in the carrier (A) is properly seated in its slot. Ensure that the slot on the inside face of the drive roller (B) is aligned with the key and slide the roller back onto the carrier. Screw the black roller retaining knob (C) back on to the end of the drive shaft and tighten.
fig.14
4.9.6 4.9.7
Set the wire speed knob to position 5 or 6. Keep the torch cable as straight as possible and press the torch switch. The wire will feed through the torch. When the wire has fed through, switch welder off, unplug from mains. a) Take torch in left hand, slide the contact tip over the wire and
screw back into place. b) Grasp gas cup in right hand, push onto torch head and turn
clockwise only. Do not turn gas cup anti-clockwise, as this will damage the internal spring. c) Cut wire so that it is just protruding from the cup.
fig.13
5. MIG/MAG WELDING
4.10.
4.10.1 4.11. 4.11.1 4.11.2 4.11.3
4.12.
4.12.1 4.12.2
Setting wire tension. Adjust the wire tension by rotating the wire tension knob. Turn clockwise to increase the tension and anticlockwise to decrease the tension. See (1) in fig13. IMPORTANT: Too little or too much tension will cause problematic wire feed and result in poor welding. Tension between rollers is checked by slowing down the wire between gloved fingers. If top feed roller skids the tension is correct. Use as low a tension as possible, too high a tension will disfigure wire and result in a blown fuse. Clutch adjustment. Note: It is essential that the clutch is adjusted correctly. Once the wire is fed through the torch, switch on the machine and set the wire speed to maximum. Depress torch switch and release quickly. If the spool overruns it indicates that the clutch is too loose. Tighten the clutch nut located in the centre of the wire spool holder with a spanner (fig.7-D) and test the machine as above until the wire stops over running. Note: DO NOT over tighten the clutch as this will cause wire feed problems and strain the motor. TURNING/CHANGING THE DRIVE Roller. (See fig.14) Ensure that the wire diameter used, is matched by the correct groove size in the drive wheel and the correct tip size on the torch as well as the correct torch liner. Failure to do this could cause the wire to slip and/ or bind. Referring to fig.12, open the wire feed mechanism by pushing the locking/wire tension knob (1) down to the right allowing the pressure roller carrier (2) to spring up revealing the feed roller. Referring to fig.14, loosen and unscrew the black feed roller retaining knob (C) and put to one side.
A spool of welding wire is positioned on the welder's spool holder and automatically fed through an insulated liner in the torch to the tip. The torch assembly consists of a switch, liner, gas hose, and control cable. The switch activates the wire feed roller and the gas flow. Conversely, releasing the switch stops the wire feed and gas flow. The weld current is transferred to the electrode (the wire) from the contact tip at the end of the torch. A gas cup fits over the contact tip to direct the gas flow towards the weld ensuring that the arc welding process is shielded from oxidising air contaminates. The shielding gas also assists heating of the weld materials. The torch is connected to the positive side of a DC rectifier, and the negative clamp is attached to the workpiece.
IMPORTANT: Should you have no welding experience, we recommend you seek training from an expert source to ensure your personal health & safety. Good Mig welding may be achieved only with continued, supervised practice.
5. 1.PREPARATION FOR WELDING IMPORTANT: BEFORE YOU COMMENCE, MAKE SURE THE MACHINE IS SWITCHED OFF AT THE MAINS. IF WELDING A CAR, DISCONNECT THE BATTERY OR FIT AN ELECTRONIC CIRCUIT PROTECTOR. WE STRONGLY RECOMMEND THE USE OF A Sealey "PROSAF/12V OR 24V IN ORDER TO PROTECT SOPHISTICATED ELECTRONICS. ENSURE YOU HAVE READ & UNDERSTOOD THE ELECTRICAL SAFETY INSTRUCTIONS IN CHAPTER 1.
5.1.1 Connecting the Earth Lead. To ensure a complete circuit, the earth lead must be securely attached to the work piece that is to be welded. a) Best connection is obtained by grinding clean the point of contact on the workpiece before connecting the earth clamp. b) The weld area must also be free of paint, rust, grease, etc. c) When welding a vehicle, be sure the vehicle battery is disconnected or fit an Electronic Circuit Protector available from your Sealey dealer.
© Jack Sealey Limited
Original Language Version
SUPERMIG180.V3 Issue No:5(D) - 11/11/16
5.1.2 5.1.3 5.1.4
5.1.5 5.1.6 5.1.7
5.1.8
Power Output switch. Set the switch to position 1 or 2 for welding
up to 2mm thickness. Use settings 3,4,5,6. for thicker welds.
Setting the welder controls. In principle, the lower the amperage
required, the slower the wire speed. See setting chart below for
voltage and corresponding wire speeds. Note: these settings are only
a guide and will vary according to the operator's experience.
Welding mild steel.
To weld and the
mild high
steel build
yuopuocf awneuldsedoCnOo²t
gas for pose a
most tasks where problem. Welding
spatter with a
long arc reduces penetration and widens the arc. This in turn results
in more spatter. A long welding arc can be appropriate for welding butt
joints in thin materials. Welding with a short arc, at the same weld
settings, results in greater penetration and a narrower weld and
reduces the amount of spatter. To achieve a consistent spatter free
and flat weld, you must use To weld aluminium use:
an
Argon/CO²
mixture.
Argon gas,
0.8mm Contact Tip,
0.8mm Aluminium Wire,
Overload Protection. Thermostatic overload protection is provided.
When an overload has occurred, leave the unit to cool. The
thermostat will automatically reset the unit when the temperature has
returned within limits
Spot Welding. Spot welding may be carried out as shown in fig.16.
It will be necessary to fit a spot welding gas cup.
(a) Overlapping metal sheets with a
maximum thickness of 0.8 mm may be welded as indicated. (b) Alternatively they may be welded
SETTINGS SHOWN AS GUIDE ONLY
edge to surface as indicated. (c) For thicker sheet pre drilled holes holes may be employed.
Wire 0.6mm Steel Argon / CO2 Mix
Use the wire feed control in conjunction with the spot weld timer beside it. To
Voltage Step:
1
2 3 4
5 66
activate the timer turn the knob clockwise. The settings indicated in the black portion
Wire Speed:
10 5 6 7 8 9 10
of the chart are for guidance only and
may vary with operators experience.
Spot Welding Timer 6
fig.15
fig.16
6. RATINGS PLATE
On the front of the welder is the ratings plate, giving the
following data:
1 - The standard relating to the safety and construction
of arc welding and associated equipment.
2 - Single phase transformer - rectifier.
3 - Welding with a continuous flow of welding wire.
4 - Single-phase AC supply.
5 - Rating of internal protection provided by casing.
6 - Output
U0: Rated minimum & maximum no load voltage.
I2, U2: Current and corresponding voltage.
X: Welding ratio based on a 10 minute cycle. 20% indicates 2 minutes welding and 8 minutes rest, 100% indicates continuous welding.
7 - Mains Supply
U1: Rated supply voltage and frequency. Imax: Maximum current.
I1eff: Maximum effective current.
8 - Welding current range.
9 - Serial Number. Specifically identifies each welder.
7.maintenance
7.1. Wire feed unit Check the wire feed unit at regular intervals. The feed roller wire guide plays an important part in obtaining consistent results. Poor wire feed affects welding. Clean the rollers weekly, especially the feed roller groove, removing all dust deposits.
7.2. Torch Protect the torch cable assembly from mechanical wear. Clean the liner from the machine forwards by using compressed air. If the liner is clogged it must be replaced.
7.3. Changing Feed Roller (See Section 4.12) 7.4. contact tip The contact tip is a consumable item and must be replaced when the hole becomes enlarged or oval. The contact tip MUSTbe kept free
from spatter to ensure an unimpeded flow of gas. Refer to fig.11 and section 3.9 for removal and replacement. 7.5. Gas Cup The gas cup must also be kept clean and free from spatter. Build up of spatter inside the gas cup can cause a short circuit at the contact tip
which will result in either the fuse blowing on the printed circuit card, or expensive machine repairs. To keep the contact tip free from spatter, we recommend the use of Sealey anti-spatter spray (MIG/722308) available from your Sealey Dealer. Refer to fig.12 and section 4.9 for removal and replacement. 7.6. Replacing the Liner Wind the wire back on to the spool and secure it. Unscrew the torch from the machine and undo the brass nut. The liner should now be visible. Pull it out and replace with a new one.
© Jack Sealey Limited
Original Language Version
SUPERMIG180.V3 Issue No:5(D) - 11/11/16
8.troubleshooting
PROBLEM
1. Power source stops 2. No weld current 3. No weld current
4. Feed motor not working, lamp is on
5. Wire does not feed, feed roller rotates
POSSIBLE CAUSE
Overheating protection activated due to overload Rectifier blown Bad connection between clamp & workpiece Break in earth lead Break in torch lead Gear damaged or worn Motor defective Pressure roller improperly adjusted Dirt, copper, dust, etc, has collected in torch liner
6. Wire feeds unevenly
7. Unstable arc 8. Porous weld
Gas cup (Nozzle) or tip defective Deformed wire Dirt, etc, in liner Gas cup (Nozzle) or Tip defective Gas cup (Nozzle) spattered Feed roller groove clogged Feed roller groove deformed Pressure roller tension improper Incorrect settings Impurities in weld area Worn or defective gas cup (nozzle) No gas Gas cup clogged Draft blowing away shielding gas Rusty or dirty joints Torch too far from or at wrong angle to work
REMEDY
Protection automatically resets when transformer has cooled (about 15 min) Replace rectifier Clean or grind contact surface and weld area Repair or replace earth lead. Repair or replace torch Replace gears. (Contact service agent) Replace motor (Contact service agent) Adjust tension Clean the liner from the machine forward. Use compressed air. If too much dirt, replace the liner. Replace gas cup (nozzle) and/or tip. (Section 3.9.4 to 3.9.7) Check roller tension and adjust it if necessary (Section 3.10) Clean the liner from the machine forward. Use compressed air Replace gas cup (nozzle) and/or tip. (Section 3.9.4 to 3.9.7) Clean or replace gas cup (nozzle) (Section 3.9.4 to 3.9.7) Clean feed roller. (Section 3.12). Replace feed roller. (Section 3.12) Adjust tension. (Section 3.10) Check settings. (Section 4) Clean and/or grind workpiece. (Section 4.1.1) Replace gas cup (nozzle). (Section 3.9.4 to 3.9.7) Open gas cylinder, regulate gas flow Clean or replace cup. (nozzle) (Section 3.9.4 to 3.9.7) Screen off welding site or increase gas flow Clean and/or grind workpiece. (Section 4.1.1) The distance from gas cup to workpiece should be 8 to 10mm
9. Electrode sticking in gas cup (nozzle)
10. Irregular weld bead 11. Weld bead too narrow and raised 12. Weld bead too wide 13. Poor penetration 14. Excessive penetration
Gas leak
Faulty Electrovalve Worn or defective gas cup (nozzle) Electrode deformed Wire speed too slow
Torch incorrectly held
Wire weaving in weld pool Weld current too low Weld speed too high Weld current too high Weld speed too low Arc too long Weld current too low Arc too long Weld current too high Weld speed too slow incorrect distance of torch to workpiece
Check hoses, connections and torch assembly. (Section 3.5). Press the gas cup in correction position Clean out or replace Replace gas cup (nozzle). (Section 3.9.4 to 3.9.7) Check roller tension. (Section 3.10) See recommendations for wire speed
Use correct torch angle
Check roller tension and adjust as needed. (Section 3.10) Increase power and wire speed. (Section 4) Move torch slower and weave a little more Decrease power and wire speed. (Section 4) Move torch faster and weave less Bring torch closer to workpiece Increase power and wire speed. (Section 4) Bring torch closer to workpiece Decrease power and wire speed. (Section 4) Move torch faster Torch distance should be 8-10mm
Environmental Protection
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable) into approved containers and dispose of the product and the fluids according to local regulations.
WEEE Regulations Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid waste authority for recycling information.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of this product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
Sole UKDistributor, Sealey Group, Kempson Way, Suffolk Business Park, Bury St. Edmunds, Suffolk,
IP32 7AR
01284 757500 01284 703534
www.sealey.co.uk
Web
email sales@sealey.co.uk
© Jack Sealey Limited
Original Language Version
SUPERMIG180.V3 Issue No:5(D) - 11/11/16
Adobe InDesign CS6 (Windows) Adobe PDF Library 10.0.1