Home › boahaus › Boahaus Model 1609 Dressing Table with Mirror Assembly Instructions PDF
ℹ️ Document Conversion Notice: This page was converted from the original file for easier reading. Diagrams/images may appear only in the original PDF below.
Document preview
File info: application/pdf · 27 pages · 2.72MB

Boahaus

Model 1609

Dressing Table with Mirror - Assembly Instructions

Contact Information

For any inquiries or replacement parts, please contact Boahaus directly:

Email: contact@boahaus.com

Phone: +1 (832) 479-1709 / (646) 491-8149 / (415) 594-5401

Website: www.boahaus.com

General Safety Information

⚠️ ATTENTION!!! Please read all instructions carefully before assembly.

1. Read the Assembly Instructions prior to assembling this product.

2. Remove all hardware from the box and sort by type.

3. Verify that all hardware and parts are present BEFORE assembling.

4. To avoid damage, assemble the product on a sturdy, level, and protective surface.

5. Wait until all steps are completed before fully tightening bolts.

6. Ensure all bolts are tightly fastened before the unit is used.

7. To move the product, you must lift it. DO NOT drag it, as dragging can cause overturning.

8. This product includes a hardware kit for wall fixing. Install this kit to prevent accidents or damages. When properly installed, this restraint can provide protection against unexpected tipping due to tremors, bumps, or climbing. The restraint is a deterrent and not a substitute for proper adult supervision. Use of tip-over restraints may reduce, but not eliminate, the risk of tip-over.

Spanish Summary: Lea las instrucciones de armado antes de ensamblar. Verifique todas las piezas. Arme sobre una superficie protegida. Espere a apretar tornillos al final. Levante el producto para moverlo, no lo arrastre. Instale el kit de fijación a la pared para prevenir volcamiento.

Product Specifications

General Dimensions

Width: 1202mm (47")

Height: 1480mm (58")

Depth: 450mm (18")

Maximum Weight Supported

Component A: 20 kg (44 lbs)

Component B: 3 kg (6.6 lbs)

Note: Weight must be evenly distributed.

Weight

Approximate product weight: 105.02 lbs. / 47.71 Kg. (Weight may vary +/- 5%)

You Will Need

  • Tools not included
  • 2 people recommended for assembly

Recommended Space for Assembly

Minimum space: 1.5m x 1.5m

Note: Place a carpet or blanket in the assembly area to avoid damage to parts during the process.

Parts Identification

Refer to the diagrams for part numbers. Key parts include:

  • Top tray (1)
  • Top base (2)
  • Side tray (5)
  • Left side (7)
  • Right side (10)
  • Mirror (11)
  • Crossbeam (12)
  • Large footer (13)
  • Small footer (14)
  • Front of large drawer (17)
  • Front of small drawer (18)
  • Rear of small drawer (20)
  • Rear of large drawer (21)
  • Bottom of drawer (22)
  • Backboard (23)
  • Drawer divide support (24)
  • Division (25)
  • Side of small right drawer (26)
  • Side of small left drawer (27)
  • Right side of large drawer (30)
  • Left side of large drawer (31)

Accessories Identification

Refer to the diagrams for accessory numbers. Key accessories include:

  • Wooden dowel (A, AS)
  • Allen key (AZ)
  • Simple minifix screw (B)
  • Drum lock (C)
  • Metallic slides (CR1, CR2)
  • Drawer slides (CR3, CR4)
  • Flat head screw (D)
  • Screw (DE)
  • Structural screw (DZ)
  • Nail (EN, H)
  • Adhesive bore patch (FM, Y)
  • Drywall Anchor (L)
  • Handle (PX)
  • Metallic angle plates (Q)
  • Mounting bracket (V)
  • Small plastic foot (X)
  • Clamp (E)
  • Flanged head screw (F)

Assembly Instructions

Note: To facilitate assembly, separate and organize all boards before you start.

Step 1: Pre-Assembly

Fix wooden dowel (A) to crossbeam (12) and large footer (13).

Fix wooden dowel (A) to small footer (14) x2.

Step 2: Base Assembly

Fix simple minifix screw (B) to top base (2).

Fix wooden dowel (A), metallic left slide (CR1), and plastic foot (X) to left side (7). Ensure the two upper holes face upwards.

Step 3: Drawer Components

Fix wooden dowel (A) to drawer sides (30/31) x8 and drawer sides (26/27) x6.

Fix wooden dowel (A) to the rear of the large drawer (21) and the rear of the small drawer (20).

Step 4: Drawer Fronts and Slides

Fix simple minifix screw (B) to the front of the large drawer (17) x4 and the front of the small drawer (18) x3.

Fix wooden dowel (A), metallic right slide (CR2) to drawer divide support (24). Flip the support (24) and fix metallic left slide (CR1).

Step 5: Side Trays and Right Side

Fix wooden dowel (A) to side tray (5) x2.

Fix wooden dowel (A), metallic right slide (CR2), and plastic foot (X) to the right side (10). Ensure the two upper holes face upwards.

Step 6: Division and Mirror Support

Fix wooden dowel (A), metallic left slide (CR1) to division (25). Flip division (25) and fix metallic right slide (CR2) and plastic foot (X). Ensure the two upper holes face upwards.

Fix wooden dowel (A) and mirror support.

Step 7: Mirror Frame Assembly

Fix side tray (5) x2 to mirror (11).

Fix top tray (1) to the previous assembly.

Note: Use allen key (AZ) to adjust structural screws (DZ).

Step 8: Main Frame Assembly

Fix top base (2) and drawer divide support (24) to the previous assembly.

Fix crossbeam (12) and large footer (13) to the left side (7) and division (25).

Note: Use allen key (AZ) to adjust structural screws (DZ).

Step 9: Footer and Side Attachment

Fix small footer (14) x2 and right side (10) to the previous assembly.

Fix both previous assemblies (14 and 17) together.

Note: Use allen key (AZ) to adjust structural screws (DZ).

Step 10: Backboard and Angle Plates

Fix backboard (23) and metallic angle plates (Q) to the previous assembly.

Note: Missing holes may need to be made with a screwdriver and screw.

Step 11: Drawer Construction (Large)

Fix side of drawer (30/31) and bottom of drawer (22) to the rear of drawer (21).

Fix front large drawer (17) x4 and handle (PX) x4 to the previous assembly.

Fix left drawer slide (CR3) x4 and right drawer slide (CR4) x4 to the large drawer x4.

Note: Missing holes may need to be made with a screwdriver and screw.

Step 12: Drawer Construction (Small)

Attach the side of the small drawer (26/27) x6 to the rear of the small drawer (20) x3.

Fix front of small drawer (18) x3 and handle (PX) x3 to the previous assembly.

Fix left drawer slide (CR3) x3 and right drawer slide (CR4) x3 to the small drawer x3.

Note: Missing holes may need to be made with a screwdriver and screw.

Step 13: Place Drawers

Place the assembled drawers into the main unit.

Step 14: Wall Mounting

WARNING: For security, it is recommended to fix the furniture to the wall to avoid overturning, which can cause serious or fatal injuries.

1. Fix mounting bracket (V) on the back of the furniture using screws (F).

2. Locate a post on the wall for the mounting bracket (V), approximately 1” below the bracket attached to the furniture. Use wall anchors (L) and screws (DE).

3. Move the furniture to its final position, aligning the wall bracket with the cabinet bracket. Pass the clamp (E) through each bracket and tighten.

4. Ensure all parts are tight.

Spanish Summary: Fije el soporte de montaje (V) en la parte posterior del mueble con tornillos (F). Localice un poste en la pared para el soporte (V), aproximadamente 1" por debajo del soporte del mueble. Use anclajes (L) y tornillos (DE). Alinee los soportes y pase la abrazadera (E). Asegure que todo esté ajustado.

Congratulations!

You have assembled your DRESSING TABLE WITH MIRROR!!!

Warranty Information

6-Months Limited Warranty

Boahaus, LLC provides a limited warranty for six months from the date of purchase against defects in materials or workmanship for furniture components. This warranty gives you specific legal rights.

Exclusions: This warranty does not cover defects resulting from:

  • Failure to follow assembly instructions, misuse, abuse, or intentional damage.
  • Fire, flood, alteration, or modification of the product.
  • Use inconsistent with intended use.
  • Incorrect or inadequate maintenance, cleaning, or care.
  • Rented products, or products purchased "used" or "as is".

Remedy: Boahaus will, at its sole option, repair, replace, or refund the value of any defective component. Replacement parts are warranted for the remaining period of the original warranty.

Limitations: Boahaus shall have no liability for incidental or consequential damages (e.g., loss of use, transportation, labor). Some states do not allow these limitations.

Transferability: This warranty applies only to the original purchaser and is void if the product is resold or transferred.

Other Warranties: No other warranties, express or implied, are applicable. Any implied warranties are limited in duration to this express warranty.

For Warranty Inquiries: Visit www.boahaus.com or contact Boahaus at +1 (832) 479-1709 / (646) 491-8149 / (415) 594-5401 or email contact@boahaus.com.

Claims may need to be submitted in writing to:

Boahaus LLC.
1250-1252 Ave. Franklin Delano Roosevelt,
San Juan, PR 00926.

Include your sales receipt or proof of purchase and a specific description of the defect.

Spanish Summary: Garantía limitada de 6 meses contra defectos de materiales o mano de obra. No cubre daños por mal uso, instalación incorrecta, etc. Boahaus reparará, reemplazará o reembolsará a su discreción. No hay responsabilidad por daños incidentales o consecuentes. La garantía es para el comprador original. Visite www.boahaus.com o contacte para consultas.

Models: 1609 Dressing Table with Mirror, 1609, Dressing Table with Mirror

Full PDF Document

Loading PDF...
Download PDF

If the inline viewer fails, it will open the original document in compatibility mode automatically. You can also open the file directly.